Blackfin: unify common ADI board settings

Rather than duplicate the same ADI settings in every ADI board, create a
common ADI config header and have all ADI boards start using that.  This
will also make merging the ~10 boards I have to forward port a lot easier.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

1 files changed, 109 insertions, 186 deletions

diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h
index 320a8c6..ef2019f 100644
--- a/include/configs/bf561-ezkit.h
+++ b/include/configs/bf561-ezkit.h
@@ -2,229 +2,152 @@
  * U-boot - Configuration file for BF561 EZKIT board
  */
 
-#ifndef __CONFIG_EZKIT561_H__
-#define __CONFIG_EZKIT561_H__
+#ifndef __CONFIG_BF561_EZKIT_H__
+#define __CONFIG_BF561_EZKIT_H__
 
 #include <asm/blackfin-config-pre.h>
 
-#define CONFIG_SYS_LONGHELP		1
-#define CONFIG_CMDLINE_EDITING	1
-#define CONFIG_BAUDRATE		57600
-/* Set default serial console for bf537 */
-#define CONFIG_UART_CONSOLE	0
-#define CONFIG_EZKIT561		1
-#define CONFIG_BOOTDELAY	5
-
-#define CONFIG_PANIC_HANG 1
-
-#define CONFIG_BFIN_CPU	bf561-0.3
-#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-
-/* This sets the default state of the cache on U-Boot's boot */
-#define CONFIG_ICACHE_ON
-#define CONFIG_DCACHE_ON
 
 /*
- * Board settings
+ * Processor Settings
  */
-#define CONFIG_DRIVER_SMC91111	1
-#define CONFIG_SMC91111_BASE	0x2C010300
-#define CONFIG_ASYNC_EBIU_BASE	CONFIG_SMC91111_BASE & ~(4*1024*1024)
-#define CONFIG_SMC_USE_32_BIT	1
-#define CONFIG_MISC_INIT_R	1
-
-/*
- * Clock settings
- */
-
-/* CONFIG_CLKIN_HZ is any value in Hz				*/
-#define CONFIG_CLKIN_HZ		30000000
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN	*/
-/*						    1=CLKIN/2	*/
-#define CONFIG_CLKIN_HALF	0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass	*/
-/*						 1=bypass PLL	*/
-#define CONFIG_PLL_BYPASS	0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is	*/
-/* Values can range from 1-64					*/
-#define CONFIG_VCO_MULT		20
-/* CONFIG_CCLK_DIV controls what the core clock divider is	*/
-/* Values can be 1, 2, 4, or 8 ONLY				*/
-#define CONFIG_CCLK_DIV		1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
-/* Values can range from 1-15					*/
-#define CONFIG_SCLK_DIV		5
-/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider	*/
-/* Values can range from 2-65535				*/
-/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD)			*/
-#define CONFIG_SPI_BAUD		2
-#define CONFIG_SPI_BAUD_INITBLOCK	4
+#define CONFIG_BFIN_CPU             bf561-0.3
+#define CONFIG_BFIN_BOOT_MODE       BFIN_BOOT_BYPASS
 
-/*
- * Network settings
- */
-#if (CONFIG_DRIVER_SMC91111)
-#define CONFIG_IPADDR		192.168.0.15
-#define CONFIG_NETMASK		255.255.255.0
-#define CONFIG_GATEWAYIP	192.168.0.1
-#define CONFIG_SERVERIP		192.168.0.2
-#define CONFIG_HOSTNAME		ezkit561
-#define CONFIG_ROOTPATH		/arm-cross-build/BF561/uClinux-dist/romfs
-#endif				/* CONFIG_DRIVER_SMC91111 */
 
 /*
- * Flash settings
+ * Clock Settings
+ *	CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ *	SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
  */
+/* CONFIG_CLKIN_HZ is any value in Hz					*/
+#define CONFIG_CLKIN_HZ			30000000
+/* CLKIN_HALF controls the DF bit in PLL_CTL      0 = CLKIN		*/
+/*                                                1 = CLKIN / 2		*/
+#define CONFIG_CLKIN_HALF		0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL  0 = do not bypass	*/
+/*                                                1 = bypass PLL	*/
+#define CONFIG_PLL_BYPASS		0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL		*/
+/* Values can range from 0-63 (where 0 means 64)			*/
+#define CONFIG_VCO_MULT			20
+/* CCLK_DIV controls the core clock divider				*/
+/* Values can be 1, 2, 4, or 8 ONLY					*/
+#define CONFIG_CCLK_DIV			1
+/* SCLK_DIV controls the system clock divider				*/
+/* Values can range from 1-15						*/
+#define CONFIG_SCLK_DIV			6
 
-#define CONFIG_SYS_FLASH_CFI		/* The flash is CFI compatible */
-#define CONFIG_FLASH_CFI_DRIVER	/* Use common CFI driver */
-#define CONFIG_SYS_FLASH_CFI_AMD_RESET
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_SYS_FLASH_BASE		0x20000000
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	135	/* max number of sectors on one chip */
-#define CONFIG_ENV_ADDR		0x20020000
-#define	CONFIG_ENV_SECT_SIZE	0x10000	/* Total Size of Environment Sector */
-/* JFFS Partition offset set  */
-#define CONFIG_SYS_JFFS2_FIRST_BANK	0
-#define CONFIG_SYS_JFFS2_NUM_BANKS	1
-/* 512k reserved for u-boot */
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR	8
 
 /*
- * SDRAM settings & memory map
+ * Memory Settings
  */
+#define CONFIG_MEM_ADD_WDTH	9
+#define CONFIG_MEM_SIZE		64
 
-#define CONFIG_MEM_SIZE			64	/* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH		9	/* 8, 9, 10, 11    */
-#define CONFIG_MEM_MT48LC16M16A2TG_75	1
-
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_MAX_RAM_SIZE	(CONFIG_MEM_SIZE * 1024 * 1024)
-
-#define CONFIG_SYS_MEMTEST_START	0x0	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		( (CONFIG_MEM_SIZE - 1) * 1024*1024)	/* 1 ... 63 MB in DRAM */
+#define CONFIG_EBIU_SDRRC_VAL	0x306
+#define CONFIG_EBIU_SDGCTL_VAL	0x91114d
 
-#define	CONFIG_LOADADDR		0x01000000	/* default load address */
-#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor   */
-#define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_EBIU_AMGCTL_VAL	0x3F
+#define CONFIG_EBIU_AMBCTL0_VAL	0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL	0xFFC27BB0
 
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()  */
-#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
+#define CONFIG_SYS_MONITOR_LEN	(256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN	(128 * 1024)
 
-#define CONFIG_SYS_GBL_DATA_SIZE	0x4000
-#define CONFIG_SYS_GBL_DATA_ADDR	(CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE	(CONFIG_SYS_GBL_DATA_ADDR  - 4)
-#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ		( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
-#else
-#define CONFIG_VCO_HZ		(( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
-#endif
-
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ		( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ		( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ		CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ		CONFIG_CLKIN_HZ
-#endif
 
 /*
- * Command settings
+ * Network Settings
  */
+#define ADI_CMDS_NETWORK	1
+#define CONFIG_DRIVER_SMC91111	1
+#define CONFIG_SMC91111_BASE	0x2C010300
+#define CONFIG_SMC_USE_32_BIT	1
+#define CONFIG_HOSTNAME		bf561-ezkit
+/* Uncomment next line to use fixed MAC address */
+/* #define CONFIG_ETHADDR	02:80:ad:20:31:e8 */
 
-#define CONFIG_SYS_AUTOLOAD	"no"	/* rarpb, bootp, dhcp commands will	*/
-				/* only perform a configuration		*/
-				/* lookup from the BOOTP/DHCP server	*/
-				/* but not try to load any image	*/
-				/* using TFTP				*/
-#define CONFIG_BOOT_RETRY_TIME	-1	/* Enable this if bootretry required, */
-					/* currently its disabled */
-#define CONFIG_BOOTCOMMAND	"run ramboot"
-#define CONFIG_BOOTARGS		"root=/dev/mtdblock0 rw console=ttyBF0,57600"
-
-#if (CONFIG_DRIVER_SMC91111)
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0"	 \
-	"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):"	\
-		"$(rootpath) console=ttyBF0,57600\0"			\
-	"addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):"	\
-		"$(gatewayip):$(netmask):$(hostname):eth0:off\0"	\
-	"ramboot=tftpboot $(loadaddr) linux; "				\
-		"run ramargs; run addip; bootelf\0"			\
-	"nfsboot=tftpboot $(loadaddr) linux; "				\
-		"run nfsargs; run addip; bootelf\0"			\
-	"update=tftpboot $(loadaddr) u-boot.bin; "			\
-		"protect off 0x20000000 0x2003FFFF; "			\
-		"erase 0x20000000 0x2003FFFF; "				\
-		"cp.b $(loadaddr) 0x20000000 $(filesize)\0"		\
-	""
-#else
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0"	 \
-	"flashboot=bootm 0x20100000\0"					\
-	""
-#endif
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
 
 /*
- * Command line configuration.
+ * Flash Settings
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_JFFS2
-
-#if defined(CONFIG_DRIVER_SMC91111)
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
+#define CONFIG_SYS_FLASH_BASE		0x20000000
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+#define CONFIG_SYS_MAX_FLASH_SECT	135
+/* The BF561-EZKIT uses a top boot flash */
+#define CONFIG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_ADDR		0x20004000
+#define CONFIG_ENV_OFFSET	(CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x10000
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
+#define ENV_IS_EMBEDDED
+#else
+#define ENV_IS_EMBEDDED_CUSTOM
 #endif
 
+
 /*
- * Console settings
+ * I2C Settings
  */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
-#define	CONFIG_SYS_PROMPT		"bfin> "	/* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size */
-#else
-#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size */
+#define CONFIG_SOFT_I2C
+#ifdef CONFIG_SOFT_I2C
+#define PF_SCL PF0
+#define PF_SDA PF1
+#define I2C_INIT \
+	do { \
+		*pFIO0_DIR |= PF_SCL; \
+		SSYNC(); \
+	} while (0)
+#define I2C_ACTIVE \
+	do { \
+		*pFIO0_DIR |= PF_SDA; \
+		*pFIO0_INEN &= ~PF_SDA; \
+		SSYNC(); \
+	} while (0)
+#define I2C_TRISTATE \
+	do { \
+		*pFIO0_DIR &= ~PF_SDA; \
+		*pFIO0_INEN |= PF_SDA; \
+		SSYNC(); \
+	} while (0)
+#define I2C_READ ((*pFIO0_FLAG_D & PF_SDA) != 0)
+#define I2C_SDA(bit) \
+	do { \
+		if (bit) \
+			*pFIO0_FLAG_S = PF_SDA; \
+		else \
+			*pFIO0_FLAG_C = PF_SDA; \
+		SSYNC(); \
+	} while (0)
+#define I2C_SCL(bit) \
+	do { \
+		if (bit) \
+			*pFIO0_FLAG_S = PF_SCL; \
+		else \
+			*pFIO0_FLAG_C = PF_SCL; \
+		SSYNC(); \
+	} while (0)
+#define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
+
+#define CONFIG_SYS_I2C_SPEED		50000
+#define CONFIG_SYS_I2C_SLAVE		0
 #endif
-#define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16		/* max number of command args */
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
 
-#define CONFIG_LOADS_ECHO	1
 
 /*
- * Miscellaneous configurable options
+ * Misc Settings
  */
-#define	CONFIG_SYS_HZ			1000		/* decrementer freq: 10 ms ticks */
-#define CONFIG_SYS_BOOTM_LEN		0x4000000	/* Large Image Length, set to 64 Meg */
+#define CONFIG_UART_CONSOLE	0
+
 
 /*
- * FLASH organization and environment definitions
+ * Pull in common ADI header for remaining command/environment setup
  */
-#define CONFIG_EBIU_SDRRC_VAL  0x306
-#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
-#define CONFIG_EBIU_SDBCTL_VAL 0x15
-
-#define CONFIG_EBIU_AMGCTL_VAL		0x3F
-#define CONFIG_EBIU_AMBCTL0_VAL		0x7BB07BB0
-#define CONFIG_EBIU_AMBCTL1_VAL		0xFFC27BB0
+#include <configs/bfin_adi_common.h>
 
 #include <asm/blackfin-config-post.h>