mv: seperate kirkwood and armada from common setting

Since there are lots of difference between kirkwood and armada series,
it is better to seperate them but still keep the most common file
shared by all marvell platform in the mv-common configure file.

This patch move the kirkwood only driver definitoin in mv-common to
the <soc_name>/config.h.

This patch is tested with compilation for armada100 and guruplug.

Signed-off-by: Lei Wen <leiwen@marvell.com>

1 files changed, 21 insertions, 126 deletions

diff --git a/include/configs/mv-common.h b/include/configs/mv-common.h
index 97b6971..a8937dd 100644
--- a/include/configs/mv-common.h
+++ b/include/configs/mv-common.h
@@ -37,54 +37,6 @@
  * High Level Configuration Options (easy to change)
  */
 #define CONFIG_MARVELL		1
-#define CONFIG_ARM926EJS	1	/* Basic Architecture */
-
-/* ====> Kirkwood Platform Common Definations */
-#if defined(CONFIG_KIRKWOOD)
-#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
-#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
-#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 for kernel */
-
-/*
- * By default kwbimage.cfg from board specific folder is used
- * If for some board, different configuration file need to be used,
- * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
- */
-#ifndef CONFIG_SYS_KWD_CONFIG
-#define	CONFIG_SYS_KWD_CONFIG	$(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg
-#endif /* CONFIG_SYS_KWD_CONFIG */
-
-/* Kirkwood has 2k of Security SRAM, use it for SP */
-#define CONFIG_SYS_INIT_SP_ADDR		0xC8012000
-#define CONFIG_NR_DRAM_BANKS_MAX	2
-
-#define CONFIG_I2C_MVTWSI_BASE	KW_TWSI_BASE
-#define MV_UART_CONSOLE_BASE	KW_UART0_BASE
-#define MV_SATA_BASE		KW_SATA_BASE
-#define MV_SATA_PORT0_OFFSET	KW_SATA_PORT0_OFFSET
-#define MV_SATA_PORT1_OFFSET	KW_SATA_PORT1_OFFSET
-
-/* ====> ARMADA100 Platform Common Definations */
-#elif defined (CONFIG_ARMADA100)
-
-#define CONFIG_SYS_TCLK		(14745600)	/* NS16550 clk config */
-#define CONFIG_SYS_HZ_CLOCK	(3250000)	/* Timer Freq. 3.25MHZ */
-#define CONFIG_MARVELL_MFP			/* Enable mvmfp driver */
-#define MV_MFPR_BASE		ARMD1_MFPR_BASE
-#define MV_UART_CONSOLE_BASE	ARMD1_UART1_BASE
-#define CONFIG_SYS_NS16550_IER	(1 << 6)	/* Bit 6 in UART_IER register
-						represents UART Unit Enable */
-/*
- * There is no internal RAM in ARMADA100, using DRAM
- * TBD: dcache to be used for this
- */
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE - 0x00200000)
-#define CONFIG_NR_DRAM_BANKS_MAX	2
-
-#else
-#error "Unsupported SoC Platform..."
-#endif
 
 /*
  * Custom CONFIG_SYS_TEXT_BASE can be done in <board>.h
@@ -138,31 +90,6 @@
 		+sizeof(CONFIG_SYS_PROMPT) + 16)	/* Print Buff */
 
 /*
- * NAND configuration
- */
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_KIRKWOOD
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define NAND_MAX_CHIPS			1
-#define CONFIG_SYS_NAND_BASE		0xD8000000	/* MV_DEFADR_NANDF */
-#define NAND_ALLOW_ERASE_ALL		1
-#define CONFIG_SYS_64BIT_VSPRINTF	/* needed for nand_util.c */
-#endif
-
-/*
- * SPI Flash configuration
- */
-#ifdef CONFIG_CMD_SF
-#define CONFIG_SPI_FLASH		1
-#define CONFIG_HARD_SPI			1
-#define CONFIG_KIRKWOOD_SPI		1
-#define CONFIG_SPI_FLASH_MACRONIX	1
-#define CONFIG_ENV_SPI_BUS		0
-#define CONFIG_ENV_SPI_CS		0
-#define CONFIG_ENV_SPI_MAX_HZ		50000000	/*50Mhz */
-#endif
-
-/*
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN	(1024 * 1024) /* 1MiB for malloc() */
@@ -176,9 +103,7 @@
 #define CONFIG_CMDLINE_EDITING
 #define CONFIG_CONSOLE_INFO_QUIET	/* some code reduction */
 #define CONFIG_ARCH_CPU_INIT	/* call arch_cpu_init() */
-#ifndef CONFIG_ARMADA100	/* will be removed latter */
 #define CONFIG_ARCH_MISC_INIT	/* call arch_misc_init() */
-#endif /* CONFIG_ARMADA100 */
 #define CONFIG_BOARD_EARLY_INIT_F /* call board_init_f for early inits */
 #define CONFIG_DISPLAY_CPUINFO	/* Display cpu info */
 #define CONFIG_STACKSIZE	0x00100000	/* regular stack- 1M */
@@ -199,27 +124,32 @@
 #endif
 #endif /* CONFIG_NR_DRAM_BANKS */
 
+/* ====> Include platform Common Definations */
+#include <asm/arch/config.h>
+
+/* ====> Include driver Common Definations */
 /*
- * Ethernet Driver configuration
+ * Common NAND configuration
  */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_CMD_MII
-#define CONFIG_NETCONSOLE	/* include NetConsole support   */
-#define CONFIG_NET_MULTI	/* specify more that one ports available */
-#define CONFIG_MII		/* expose smi ove miiphy interface */
-#define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
-#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
-#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
-#endif /* CONFIG_CMD_NET */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define NAND_MAX_CHIPS                 1
+#define CONFIG_SYS_64BIT_VSPRINTF      /* needed for nand_util.c */
+#endif
+
+/*
+ * Common SPI Flash configuration
+ */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH		1
+#define CONFIG_SPI_FLASH_MACRONIX	1
+#endif
 
 /*
- * USB/EHCI
+ * Common USB/EHCI configuration
  */
 #ifdef CONFIG_CMD_USB
 #define CONFIG_USB_EHCI		/* Enable EHCI USB support */
-#define CONFIG_USB_EHCI_KIRKWOOD
-#define CONFIG_EHCI_IS_TDI
 #define CONFIG_USB_STORAGE
 #define CONFIG_DOS_PARTITION
 #define CONFIG_ISO_PARTITION
@@ -227,44 +157,9 @@
 #endif /* CONFIG_CMD_USB */
 
 /*
- * IDE Support on SATA ports
- */
-#ifdef CONFIG_CMD_IDE
-#define __io
-#define CONFIG_CMD_EXT2
-#define CONFIG_MVSATA_IDE
-#define CONFIG_IDE_PREINIT
-#define CONFIG_MVSATA_IDE_USE_PORT1
-/* Needs byte-swapping for ATA data register */
-#define CONFIG_IDE_SWAP_IO
-/* Data, registers and alternate blocks are at the same offset */
-#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
-#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
-#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
-/* Each 8-bit ATA register is aligned to a 4-bytes address */
-#define CONFIG_SYS_ATA_STRIDE		4
-/* Controller supports 48-bits LBA addressing */
-#define CONFIG_LBA48
-/* CONFIG_CMD_IDE requires some #defines for ATA registers */
-#define CONFIG_SYS_IDE_MAXBUS		2
-#define CONFIG_SYS_IDE_MAXDEVICE	2
-/* ATA registers base is at SATA controller base */
-#define CONFIG_SYS_ATA_BASE_ADDR	MV_SATA_BASE
-#endif /* CONFIG_CMD_IDE */
-
-/*
- * I2C related stuff
- */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_I2C_MVTWSI
-#define CONFIG_SYS_I2C_SLAVE		0x0
-#define CONFIG_SYS_I2C_SPEED		100000
-#endif
-
-/*
  * File system
  */
-#ifndef CONFIG_ARMADA100	/* will be removed latter */
+#ifdef CONFIG_SYS_MVFS
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_FAT
@@ -275,6 +170,6 @@
 #define CONFIG_MTD_PARTITIONS
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_LZO
-#endif /* CONFIG_ARMADA100 */
+#endif
 
 #endif /* _MV_COMMON_H */