diff options
Diffstat (limited to 'board/amcc/bamboo/bamboo.h')
-rw-r--r-- | board/amcc/bamboo/bamboo.h | 367 |
1 files changed, 0 insertions, 367 deletions
diff --git a/board/amcc/bamboo/bamboo.h b/board/amcc/bamboo/bamboo.h deleted file mode 100644 index f2b78a9..0000000 --- a/board/amcc/bamboo/bamboo.h +++ /dev/null @@ -1,367 +0,0 @@ -/* - * (C) Copyright 2005 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/*----------------------------------------------------------------------------+ - | FPGA registers and bit definitions - +----------------------------------------------------------------------------*/ -/* - * PowerPC 440EP Board FPGA is reached with physical address 0x80001FF0. - * TLB initialization makes it correspond to logical address 0x80001FF0. - * => Done init_chip.s in bootlib - */ -#define FPGA_BASE_ADDR 0x80002000 - -/*----------------------------------------------------------------------------+ - | Board Jumpers Setting Register - | Board Settings provided by jumpers - +----------------------------------------------------------------------------*/ -#define FPGA_SETTING_REG (FPGA_BASE_ADDR+0x3) -/* Boot from small flash */ -#define FPGA_SET_REG_BOOT_SMALL_FLASH 0x80 -/* Operational Flash versus SRAM position in Memory Map */ -#define FPGA_SET_REG_OP_CODE_SRAM_SEL_MASK 0x40 -#define FPGA_SET_REG_OP_CODE_FLASH_ABOVE 0x40 -#define FPGA_SET_REG_SRAM_ABOVE 0x00 -/* Boot From NAND Flash */ -#define FPGA_SET_REG_BOOT_NAND_FLASH_MASK 0x40 -#define FPGA_SET_REG_BOOT_NAND_FLASH_SELECT 0x00 -/* On Board PCI Arbiter Select */ -#define FPGA_SET_REG_PCI_EXT_ARBITER_SEL_MASK 0x10 -#define FPGA_SET_REG_PCI_EXT_ARBITER_SEL 0x00 - -/*----------------------------------------------------------------------------+ - | Functions Selection Register 1 - +----------------------------------------------------------------------------*/ -#define FPGA_SELECTION_1_REG (FPGA_BASE_ADDR+0x4) -#define FPGA_SEL_1_REG_PHY_MASK 0xE0 -#define FPGA_SEL_1_REG_MII 0x80 -#define FPGA_SEL_1_REG_RMII 0x40 -#define FPGA_SEL_1_REG_SMII 0x20 -#define FPGA_SEL_1_REG_USB2_DEV_SEL 0x10 /* USB2 Device Selection */ -#define FPGA_SEL_1_REG_USB2_HOST_SEL 0x08 /* USB2 Host Selection */ -#define FPGA_SEL_1_REG_NF_SELEC_MASK 0x07 /* NF Selection Mask */ -#define FPGA_SEL_1_REG_NF0_SEL_BY_NFCS1 0x04 /* NF0 Selected by NF_CS1 */ -#define FPGA_SEL_1_REG_NF1_SEL_BY_NFCS2 0x02 /* NF1 Selected by NF_CS2 */ -#define FPGA_SEL_1_REG_NF1_SEL_BY_NFCS3 0x01 /* NF1 Selected by NF_CS3 */ - -/*----------------------------------------------------------------------------+ - | Functions Selection Register 2 - +----------------------------------------------------------------------------*/ -#define FPGA_SELECTION_2_REG (FPGA_BASE_ADDR+0x5) -#define FPGA_SEL2_REG_IIC1_SCP_SEL_MASK 0x80 /* IIC1 / SCP Selection */ -#define FPGA_SEL2_REG_SEL_FRAM 0x80 /* FRAM on IIC1 bus selected - SCP Select */ -#define FPGA_SEL2_REG_SEL_SCP 0x80 /* Identical to SCP Selection */ -#define FPGA_SEL2_REG_SEL_IIC1 0x00 /* IIC1 Selection - Default Value */ -#define FPGA_SEL2_REG_SEL_DMA_A_B 0x40 /* DMA A & B channels selected */ -#define FPGA_SEL2_REG_SEL_DMA_C_D 0x20 /* DMA C & D channels selected */ -#define FPGA_SEL2_REG_DMA_EOT_TC_3_SEL 0x10 /* 0 = EOT - input to 440EP */ - /* 1 = TC - output from 440EP */ -#define FPGA_SEL2_REG_DMA_EOT_TC_2_SEL 0x08 /* 0 = EOT (input to 440EP) */ - /* 1 = TC (output from 440EP) */ -#define FPGA_SEL2_REG_SEL_GPIO_1 0x04 /* EBC_GPIO & USB2_GPIO selected */ -#define FPGA_SEL2_REG_SEL_GPIO_2 0x02 /* Ether._GPIO & UART_GPIO selected */ -#define FPGA_SEL2_REG_SEL_GPIO_3 0x01 /* DMA_GPIO & Trace_GPIO selected */ - -/*----------------------------------------------------------------------------+ - | Functions Selection Register 3 - +----------------------------------------------------------------------------*/ -#define FPGA_SELECTION_3_REG (FPGA_BASE_ADDR+0x6) -#define FPGA_SEL3_REG_EXP_SLOT_EN 0x80 /* Expansion Slot enabled */ -#define FPGA_SEL3_REG_SEL_UART_CONFIG_MASK 0x70 -#define FPGA_SEL3_REG_SEL_UART_CONFIG1 0x40 /* one 8_pin UART */ -#define FPGA_SEL3_REG_SEL_UART_CONFIG2 0x20 /* two 4_pin UARTs */ -#define FPGA_SEL3_REG_SEL_UART_CONFIG3 0x10 /* one 4_pin & two 2_pin UARTs */ -#define FPGA_SEL3_REG_SEL_UART_CONFIG4 0x08 /* four 2_pin UARTs */ -#define FPGA_SEL3_REG_DTR_DSR_MODE_4_PIN_UART 0x00 /* DTR/DSR mode for 4_pin_UART */ -#define FPGA_SEL3_REG_RTS_CTS_MODE_4_PIN_UART 0x04 /* RTS/CTS mode for 4_pin_UART */ - -/*----------------------------------------------------------------------------+ - | Soft Reset Register - +----------------------------------------------------------------------------*/ -#define FPGA_RESET_REG (FPGA_BASE_ADDR+0x7) -#define FPGA_RESET_REG_RESET_USB20_DEV 0x80 /* Hard Reset of the GT3200 */ -#define FPGA_RESET_REG_RESET_DISPLAY 0x40 /* Hard Reset on Display Device */ -#define FPGA_RESET_REG_STATUS_LED_0 0x08 /* 1 = Led On */ -#define FPGA_RESET_REG_STATUS_LED_1 0x04 /* 1 = Led On */ -#define FPGA_RESET_REG_STATUS_LED_2 0x02 /* 1 = Led On */ -#define FPGA_RESET_REG_STATUS_LED_3 0x01 /* 1 = Led On */ - - -/*----------------------------------------------------------------------------+ -| SDR Configuration registers -+----------------------------------------------------------------------------*/ -#define SDR0_SDSTP1_EBC_ROM_BS_MASK 0x00006000 /* EBC Boot Size Mask */ -#define SDR0_SDSTP1_EBC_ROM_BS_32BIT 0x00004000 /* EBC 32 bits */ -#define SDR0_SDSTP1_EBC_ROM_BS_16BIT 0x00002000 /* EBC 16 Bits */ -#define SDR0_SDSTP1_EBC_ROM_BS_8BIT 0x00000000 /* EBC 8 Bits */ - -#define SDR0_SDSTP1_BOOT_SEL_MASK 0x00001800 /* Boot device Selection Mask */ -#define SDR0_SDSTP1_BOOT_SEL_EBC 0x00000000 /* EBC */ -#define SDR0_SDSTP1_BOOT_SEL_PCI 0x00000800 /* PCI */ -#define SDR0_SDSTP1_BOOT_SEL_NDFC 0x00001000 /* NDFC */ - -/* Serial Device Enabled - Addr = 0xA8 */ -#define SDR0_PSTRP0_BOOTSTRAP_IIC_A8_EN SDR0_PSTRP0_BOOTSTRAP_SETTINGS5 -/* Serial Device Enabled - Addr = 0xA4 */ -#define SDR0_PSTRP0_BOOTSTRAP_IIC_A4_EN SDR0_PSTRP0_BOOTSTRAP_SETTINGS7 - -/* Pin Straps Reg */ -#define SDR0_PSTRP0 0x0040 -#define SDR0_PSTRP0_BOOTSTRAP_MASK 0xE0000000 /* Strap Bits */ - -#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS0 0x00000000 /* Default strap settings 0 */ -#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS1 0x20000000 /* Default strap settings 1 */ -#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS2 0x40000000 /* Default strap settings 2 */ -#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS3 0x60000000 /* Default strap settings 3 */ -#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS4 0x80000000 /* Default strap settings 4 */ -#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS5 0xA0000000 /* Default strap settings 5 */ -#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS6 0xC0000000 /* Default strap settings 6 */ -#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS7 0xE0000000 /* Default strap settings 7 */ - -/*----------------------------------------------------------------------------+ -| EBC Configuration Register - EBC0_CFG -+----------------------------------------------------------------------------*/ -/* External Bus Three-State Control */ -#define EBC0_CFG_EBTC_DRIVEN 0x80000000 -/* Device-Paced Time-out Disable */ -#define EBC0_CFG_PTD_ENABLED 0x00000000 -/* Ready Timeout Count */ -#define EBC0_CFG_RTC_MASK 0x38000000 -#define EBC0_CFG_RTC_16PERCLK 0x00000000 -#define EBC0_CFG_RTC_32PERCLK 0x08000000 -#define EBC0_CFG_RTC_64PERCLK 0x10000000 -#define EBC0_CFG_RTC_128PERCLK 0x18000000 -#define EBC0_CFG_RTC_256PERCLK 0x20000000 -#define EBC0_CFG_RTC_512PERCLK 0x28000000 -#define EBC0_CFG_RTC_1024PERCLK 0x30000000 -#define EBC0_CFG_RTC_2048PERCLK 0x38000000 -/* External Master Priority Low */ -#define EBC0_CFG_EMPL_LOW 0x00000000 -#define EBC0_CFG_EMPL_MEDIUM_LOW 0x02000000 -#define EBC0_CFG_EMPL_MEDIUM_HIGH 0x04000000 -#define EBC0_CFG_EMPL_HIGH 0x06000000 -/* External Master Priority High */ -#define EBC0_CFG_EMPH_LOW 0x00000000 -#define EBC0_CFG_EMPH_MEDIUM_LOW 0x00800000 -#define EBC0_CFG_EMPH_MEDIUM_HIGH 0x01000000 -#define EBC0_CFG_EMPH_HIGH 0x01800000 -/* Chip Select Three-State Control */ -#define EBC0_CFG_CSTC_DRIVEN 0x00400000 -/* Burst Prefetch */ -#define EBC0_CFG_BPF_ONEDW 0x00000000 -#define EBC0_CFG_BPF_TWODW 0x00100000 -#define EBC0_CFG_BPF_FOURDW 0x00200000 -/* External Master Size */ -#define EBC0_CFG_EMS_8BIT 0x00000000 -/* Power Management Enable */ -#define EBC0_CFG_PME_DISABLED 0x00000000 -#define EBC0_CFG_PME_ENABLED 0x00020000 -/* Power Management Timer */ -#define EBC0_CFG_PMT_ENCODE(n) ((((unsigned long)(n))&0x1F)<<12) - -/*----------------------------------------------------------------------------+ -| Peripheral Bank Configuration Register - EBC0_BnCR -+----------------------------------------------------------------------------*/ -/* BAS - Base Address Select */ -#define EBC0_BNCR_BAS_ENCODE(n) ((((unsigned long)(n))&0xFFF00000)<<0) -/* BS - Bank Size */ -#define EBC0_BNCR_BS_MASK 0x000E0000 -#define EBC0_BNCR_BS_1MB 0x00000000 -#define EBC0_BNCR_BS_2MB 0x00020000 -#define EBC0_BNCR_BS_4MB 0x00040000 -#define EBC0_BNCR_BS_8MB 0x00060000 -#define EBC0_BNCR_BS_16MB 0x00080000 -#define EBC0_BNCR_BS_32MB 0x000A0000 -#define EBC0_BNCR_BS_64MB 0x000C0000 -#define EBC0_BNCR_BS_128MB 0x000E0000 -/* BU - Bank Usage */ -#define EBC0_BNCR_BU_MASK 0x00018000 -#define EBC0_BNCR_BU_RO 0x00008000 -#define EBC0_BNCR_BU_WO 0x00010000 -#define EBC0_BNCR_BU_RW 0x00018000 -/* BW - Bus Width */ -#define EBC0_BNCR_BW_MASK 0x00006000 -#define EBC0_BNCR_BW_8BIT 0x00000000 -#define EBC0_BNCR_BW_16BIT 0x00002000 -#define EBC0_BNCR_BW_32BIT 0x00004000 - -/*----------------------------------------------------------------------------+ -| Peripheral Bank Access Parameters - EBC0_BnAP -+----------------------------------------------------------------------------*/ -/* Burst Mode Enable */ -#define EBC0_BNAP_BME_ENABLED 0x80000000 -#define EBC0_BNAP_BME_DISABLED 0x00000000 -/* Transfert Wait */ -#define EBC0_BNAP_TWT_ENCODE(n) ((((unsigned long)(n))&0xFF)<<23) /* Bits 1:8 */ -/* Chip Select On Timing */ -#define EBC0_BNAP_CSN_ENCODE(n) ((((unsigned long)(n))&0x3)<<18) /* Bits 12:13 */ -/* Output Enable On Timing */ -#define EBC0_BNAP_OEN_ENCODE(n) ((((unsigned long)(n))&0x3)<<16) /* Bits 14:15 */ -/* Write Back Enable On Timing */ -#define EBC0_BNAP_WBN_ENCODE(n) ((((unsigned long)(n))&0x3)<<14) /* Bits 16:17 */ -/* Write Back Enable Off Timing */ -#define EBC0_BNAP_WBF_ENCODE(n) ((((unsigned long)(n))&0x3)<<12) /* Bits 18:19 */ -/* Transfert Hold */ -#define EBC0_BNAP_TH_ENCODE(n) ((((unsigned long)(n))&0x7)<<9) /* Bits 20:22 */ -/* PerReady Enable */ -#define EBC0_BNAP_RE_ENABLED 0x00000100 -#define EBC0_BNAP_RE_DISABLED 0x00000000 -/* Sample On Ready */ -#define EBC0_BNAP_SOR_DELAYED 0x00000000 -#define EBC0_BNAP_SOR_NOT_DELAYED 0x00000080 -/* Byte Enable Mode */ -#define EBC0_BNAP_BEM_WRITEONLY 0x00000000 -#define EBC0_BNAP_BEM_RW 0x00000040 -/* Parity Enable */ -#define EBC0_BNAP_PEN_DISABLED 0x00000000 -#define EBC0_BNAP_PEN_ENABLED 0x00000020 - -/*----------------------------------------------------------------------------+ -| Define Boot devices -+----------------------------------------------------------------------------*/ -/* */ -#define BOOT_FROM_SMALL_FLASH 0x00 -#define BOOT_FROM_LARGE_FLASH_OR_SRAM 0x01 -#define BOOT_FROM_NAND_FLASH0 0x02 -#define BOOT_FROM_PCI 0x03 -#define BOOT_DEVICE_UNKNOWN 0x04 - - -#define PVR_POWERPC_440EP_PASS1 0x42221850 -#define PVR_POWERPC_440EP_PASS2 0x422218D3 - -#define TRUE 1 -#define FALSE 0 - -#define GPIO0 0 -#define GPIO1 1 - -/*#define MAX_SELECTION_NB CORE_NB */ -#define MAX_CORE_SELECT_NB 22 - -/*----------------------------------------------------------------------------+ - | PPC440EP GPIOs addresses. - +----------------------------------------------------------------------------*/ -#define GPIO0_REAL 0xEF600B00 - -#define GPIO1_REAL 0xEF600C00 - -/* Offsets */ -#define GPIOx_OR 0x00 /* GPIO Output Register */ -#define GPIOx_TCR 0x04 /* GPIO Three-State Control Register */ -#define GPIOx_OSL 0x08 /* GPIO Output Select Register (Bits 0-31) */ -#define GPIOx_OSH 0x0C /* GPIO Ouput Select Register (Bits 32-63) */ -#define GPIOx_TSL 0x10 /* GPIO Three-State Select Register (Bits 0-31) */ -#define GPIOx_TSH 0x14 /* GPIO Three-State Select Register (Bits 32-63) */ -#define GPIOx_ODR 0x18 /* GPIO Open drain Register */ -#define GPIOx_IR 0x1C /* GPIO Input Register */ -#define GPIOx_RR1 0x20 /* GPIO Receive Register 1 */ -#define GPIOx_RR2 0x24 /* GPIO Receive Register 2 */ -#define GPIOx_RR3 0x28 /* GPIO Receive Register 3 */ -#define GPIOx_IS1L 0x30 /* GPIO Input Select Register 1 (Bits 0-31) */ -#define GPIOx_IS1H 0x34 /* GPIO Input Select Register 1 (Bits 32-63) */ -#define GPIOx_IS2L 0x38 /* GPIO Input Select Register 2 (Bits 0-31) */ -#define GPIOx_IS2H 0x3C /* GPIO Input Select Register 2 (Bits 32-63) */ -#define GPIOx_IS3L 0x40 /* GPIO Input Select Register 3 (Bits 0-31) */ -#define GPIOx_IS3H 0x44 /* GPIO Input Select Register 3 (Bits 32-63) */ - -/* GPIO0 */ -#define GPIO0_IS1L (GPIO0_BASE+GPIOx_IS1L) -#define GPIO0_IS1H (GPIO0_BASE+GPIOx_IS1H) -#define GPIO0_IS2L (GPIO0_BASE+GPIOx_IS2L) -#define GPIO0_IS2H (GPIO0_BASE+GPIOx_IS2H) -#define GPIO0_IS3L (GPIO0_BASE+GPIOx_IS3L) -#define GPIO0_IS3H (GPIO0_BASE+GPIOx_IS3L) - -/* GPIO1 */ -#define GPIO1_IS1L (GPIO1_BASE+GPIOx_IS1L) -#define GPIO1_IS1H (GPIO1_BASE+GPIOx_IS1H) -#define GPIO1_IS2L (GPIO1_BASE+GPIOx_IS2L) -#define GPIO1_IS2H (GPIO1_BASE+GPIOx_IS2H) -#define GPIO1_IS3L (GPIO1_BASE+GPIOx_IS3L) -#define GPIO1_IS3H (GPIO1_BASE+GPIOx_IS3L) - -#define GPIO_OS(x) (x+GPIOx_OSL) /* GPIO Output Register High or Low */ -#define GPIO_TS(x) (x+GPIOx_TSL) /* GPIO Three-state Control Reg High or Low */ -#define GPIO_IS1(x) (x+GPIOx_IS1L) /* GPIO Input register1 High or Low */ -#define GPIO_IS2(x) (x+GPIOx_IS2L) /* GPIO Input register2 High or Low */ -#define GPIO_IS3(x) (x+GPIOx_IS3L) /* GPIO Input register3 High or Low */ - - -/*----------------------------------------------------------------------------+ - | XX XX - | - | XXXXXX XXX XX XXX XXX - | XX XX X XX XX XX - | XX XX X XX XX XX - | XX XX XX XX XX - | XXXXXX XXX XXX XXXX XXXX - +----------------------------------------------------------------------------*/ -/*----------------------------------------------------------------------------+ - | Defines - +----------------------------------------------------------------------------*/ -typedef enum zmii_config { ZMII_CONFIGURATION_UNKNOWN, - ZMII_CONFIGURATION_IS_MII, - ZMII_CONFIGURATION_IS_RMII, - ZMII_CONFIGURATION_IS_SMII -} zmii_config_t; - -/*----------------------------------------------------------------------------+ - | Declare Configuration values - +----------------------------------------------------------------------------*/ -typedef enum uart_config_nb { L1, L2, L3, L4 } uart_config_nb_t; -typedef enum core_selection { CORE_NOT_SELECTED, CORE_SELECTED} core_selection_t; -typedef enum config_list { IIC_CORE, - SCP_CORE, - DMA_CHANNEL_AB, - UIC_4_9, - USB2_HOST, - DMA_CHANNEL_CD, - USB2_DEVICE, - PACKET_REJ_FUNC_AVAIL, - USB1_DEVICE, - EBC_MASTER, - NAND_FLASH, - UART_CORE0, - UART_CORE1, - UART_CORE2, - UART_CORE3, - MII_SEL, - RMII_SEL, - SMII_SEL, - PACKET_REJ_FUNC_EN, - UIC_0_3, - USB1_HOST, - PCI_PATCH, - CORE_NB -} core_list_t; - -typedef enum block3_value { B3_V1, B3_V2, B3_V3, B3_V4, B3_V5, - B3_V6, B3_V7, B3_V8, B3_V9, B3_V10, - B3_V11, B3_V12, B3_V13, B3_V14, B3_V15, - B3_V16, B3_VALUE_UNKNOWN -} block3_value_t; - -typedef enum config_validity { CONFIG_IS_VALID, - CONFIG_IS_INVALID -} config_validity_t; |