1 files changed, 0 insertions, 387 deletions
diff --git a/cpu/arm926ejs/kirkwood/cpu.c b/cpu/arm926ejs/kirkwood/cpu.c
deleted file mode 100644
index 6fc3902..0000000
--- a/cpu/arm926ejs/kirkwood/cpu.c
+++ /dev/null
@@ -1,387 +0,0 @@
-/*
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301 USA
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/cache.h>
-#include <u-boot/md5.h>
-#include <asm/arch/kirkwood.h>
-#include <hush.h>
-
-#define BUFLEN	16
-
-void reset_cpu(unsigned long ignored)
-{
-	struct kwcpu_registers *cpureg =
-	    (struct kwcpu_registers *)KW_CPU_REG_BASE;
-
-	writel(readl(&cpureg->rstoutn_mask) | (1 << 2),
-		&cpureg->rstoutn_mask);
-	writel(readl(&cpureg->sys_soft_rst) | 1,
-		&cpureg->sys_soft_rst);
-	while (1) ;
-}
-
-/*
- * Generates Ramdom hex number reading some time varient system registers
- * and using md5 algorithm
- */
-unsigned char get_random_hex(void)
-{
-	int i;
-	u32 inbuf[BUFLEN];
-	u8 outbuf[BUFLEN];
-
-	/*
-	 * in case of 88F6281/88F6192 A0,
-	 * Bit7 need to reset to generate random values in KW_REG_UNDOC_0x1470
-	 * Soc reg offsets KW_REG_UNDOC_0x1470 and KW_REG_UNDOC_0x1478 are reserved regs and
-	 * Does not have names at this moment (no errata available)
-	 */
-	writel(readl(KW_REG_UNDOC_0x1478) & ~(1 << 7), KW_REG_UNDOC_0x1478);
-	for (i = 0; i < BUFLEN; i++) {
-		inbuf[i] = readl(KW_REG_UNDOC_0x1470);
-	}
-	md5((u8 *) inbuf, (BUFLEN * sizeof(u32)), outbuf);
-	return outbuf[outbuf[7] % 0x0f];
-}
-
-/*
- * Window Size
- * Used with the Base register to set the address window size and location.
- * Must be programmed from LSB to MSB as sequence of ones followed by
- * sequence of zeros. The number of ones specifies the size of the window in
- * 64 KByte granularity (e.g., a value of 0x00FF specifies 256 = 16 MByte).
- * NOTE: A value of 0x0 specifies 64-KByte size.
- */
-unsigned int kw_winctrl_calcsize(unsigned int sizeval)
-{
-	int i;
-	unsigned int j = 0;
-	u32 val = sizeval >> 1;
-
-	for (i = 0; val > 0x10000; i++) {
-		j |= (1 << i);
-		val = val >> 1;
-	}
-	return (0x0000ffff & j);
-}
-
-/*
- * kw_config_adr_windows - Configure address Windows
- *
- * There are 8 address windows supported by Kirkwood Soc to addess different
- * devices. Each window can be configured for size, BAR and remap addr
- * Below configuration is standard for most of the cases
- *
- * If remap function not used, remap_lo must be set as base
- *
- * Reference Documentation:
- * Mbus-L to Mbus Bridge Registers Configuration.
- * (Sec 25.1 and 25.3 of Datasheet)
- */
-int kw_config_adr_windows(void)
-{
-	struct kwwin_registers *winregs =
-		(struct kwwin_registers *)KW_CPU_WIN_BASE;
-
-	/* Window 0: PCIE MEM address space */
-	writel(KWCPU_WIN_CTRL_DATA(1024 * 1024 * 256, KWCPU_TARGET_PCIE,
-		KWCPU_ATTR_PCIE_MEM, KWCPU_WIN_ENABLE), &winregs[0].ctrl);
-
-	writel(KW_DEFADR_PCI_MEM, &winregs[0].base);
-	writel(KW_DEFADR_PCI_MEM, &winregs[0].remap_lo);
-	writel(0x0, &winregs[0].remap_hi);
-
-	/* Window 1: PCIE IO address space */
-	writel(KWCPU_WIN_CTRL_DATA(1024 * 64, KWCPU_TARGET_PCIE,
-		KWCPU_ATTR_PCIE_IO, KWCPU_WIN_ENABLE), &winregs[1].ctrl);
-	writel(KW_DEFADR_PCI_IO, &winregs[1].base);
-	writel(KW_DEFADR_PCI_IO_REMAP, &winregs[1].remap_lo);
-	writel(0x0, &winregs[1].remap_hi);
-
-	/* Window 2: NAND Flash address space */
-	writel(KWCPU_WIN_CTRL_DATA(1024 * 1024 * 128, KWCPU_TARGET_MEMORY,
-		KWCPU_ATTR_NANDFLASH, KWCPU_WIN_ENABLE), &winregs[2].ctrl);
-	writel(KW_DEFADR_NANDF, &winregs[2].base);
-	writel(KW_DEFADR_NANDF, &winregs[2].remap_lo);
-	writel(0x0, &winregs[2].remap_hi);
-
-	/* Window 3: SPI Flash address space */
-	writel(KWCPU_WIN_CTRL_DATA(1024 * 1024 * 128, KWCPU_TARGET_MEMORY,
-		KWCPU_ATTR_SPIFLASH, KWCPU_WIN_ENABLE), &winregs[3].ctrl);
-	writel(KW_DEFADR_SPIF, &winregs[3].base);
-	writel(KW_DEFADR_SPIF, &winregs[3].remap_lo);
-	writel(0x0, &winregs[3].remap_hi);
-
-	/* Window 4: BOOT Memory address space */
-	writel(KWCPU_WIN_CTRL_DATA(1024 * 1024 * 128, KWCPU_TARGET_MEMORY,
-		KWCPU_ATTR_BOOTROM, KWCPU_WIN_ENABLE), &winregs[4].ctrl);
-	writel(KW_DEFADR_BOOTROM, &winregs[4].base);
-
-	/* Window 5: Security SRAM address space */
-	writel(KWCPU_WIN_CTRL_DATA(1024 * 64, KWCPU_TARGET_SASRAM,
-		KWCPU_ATTR_SASRAM, KWCPU_WIN_ENABLE), &winregs[5].ctrl);
-	writel(KW_DEFADR_SASRAM, &winregs[5].base);
-
-	/* Window 6-7: Disabled */
-	writel(KWCPU_WIN_DISABLE, &winregs[6].ctrl);
-	writel(KWCPU_WIN_DISABLE, &winregs[7].ctrl);
-
-	return 0;
-}
-
-/*
- * kw_config_gpio - GPIO configuration
- */
-void kw_config_gpio(u32 gpp0_oe_val, u32 gpp1_oe_val, u32 gpp0_oe, u32 gpp1_oe)
-{
-	struct kwgpio_registers *gpio0reg =
-		(struct kwgpio_registers *)KW_GPIO0_BASE;
-	struct kwgpio_registers *gpio1reg =
-		(struct kwgpio_registers *)KW_GPIO1_BASE;
-
-	/* Init GPIOS to default values as per board requirement */
-	writel(gpp0_oe_val, &gpio0reg->dout);
-	writel(gpp1_oe_val, &gpio1reg->dout);
-	writel(gpp0_oe, &gpio0reg->oe);
-	writel(gpp1_oe, &gpio1reg->oe);
-}
-
-/*
- * kw_config_mpp - Multi-Purpose Pins Functionality configuration
- *
- * Each MPP can be configured to different functionality through
- * MPP control register, ref (sec 6.1 of kirkwood h/w specification)
- *
- * There are maximum 64 Multi-Pourpose Pins on Kirkwood
- * Each MPP functionality can be configuration by a 4bit value
- * of MPP control reg, the value and associated functionality depends
- * upon used SoC varient
- */
-int kw_config_mpp(u32 mpp0_7, u32 mpp8_15, u32 mpp16_23, u32 mpp24_31,
-		u32 mpp32_39, u32 mpp40_47, u32 mpp48_55)
-{
-	u32 *mppreg = (u32 *) KW_MPP_BASE;
-
-	/* program mpp registers */
-	writel(mpp0_7, &mppreg[0]);
-	writel(mpp8_15, &mppreg[1]);
-	writel(mpp16_23, &mppreg[2]);
-	writel(mpp24_31, &mppreg[3]);
-	writel(mpp32_39, &mppreg[4]);
-	writel(mpp40_47, &mppreg[5]);
-	writel(mpp48_55, &mppreg[6]);
-	return 0;
-}
-
-/*
- * SYSRSTn Duration Counter Support
- *
- * Kirkwood SoC implements a hardware-based SYSRSTn duration counter.
- * When SYSRSTn is asserted low, a SYSRSTn duration counter is running.
- * The SYSRSTn duration counter is useful for implementing a manufacturer
- * or factory reset. Upon a long reset assertion that is greater than a
- * pre-configured environment variable value for sysrstdelay,
- * The counter value is stored in the SYSRSTn Length Counter Register
- * The counter is based on the 25-MHz reference clock (40ns)
- * It is a 29-bit counter, yielding a maximum counting duration of
- * 2^29/25 MHz (21.4 seconds). When the counter reach its maximum value,
- * it remains at this value until counter reset is triggered by setting
- * bit 31 of KW_REG_SYSRST_CNT
- */
-static void kw_sysrst_action(void)
-{
-	int ret;
-	char *s = getenv("sysrstcmd");
-
-	if (!s) {
-		debug("Error.. %s failed, check sysrstcmd\n",
-			__FUNCTION__);
-		return;
-	}
-
-	debug("Starting %s process...\n", __FUNCTION__);
-#if !defined(CONFIG_SYS_HUSH_PARSER)
-	ret = run_command (s, 0);
-#else
-	ret = parse_string_outer(s, FLAG_PARSE_SEMICOLON
-				  | FLAG_EXIT_FROM_LOOP);
-#endif
-	if (ret < 0)
-		debug("Error.. %s failed\n", __FUNCTION__);
-	else
-		debug("%s process finished\n", __FUNCTION__);
-}
-
-static void kw_sysrst_check(void)
-{
-	u32 sysrst_cnt, sysrst_dly;
-	char *s;
-
-	/*
-	 * no action if sysrstdelay environment variable is not defined
-	 */
-	s = getenv("sysrstdelay");
-	if (s == NULL)
-		return;
-
-	/* read sysrstdelay value */
-	sysrst_dly = (u32) simple_strtoul(s, NULL, 10);
-
-	/* read SysRst Length counter register (bits 28:0) */
-	sysrst_cnt = (0x1fffffff & readl(KW_REG_SYSRST_CNT));
-	debug("H/w Rst hold time: %d.%d secs\n",
-		sysrst_cnt / SYSRST_CNT_1SEC_VAL,
-		sysrst_cnt % SYSRST_CNT_1SEC_VAL);
-
-	/* clear the counter for next valid read*/
-	writel(1 << 31, KW_REG_SYSRST_CNT);
-
-	/*
-	 * sysrst_action:
-	 * if H/w Reset key is pressed and hold for time
-	 * more than sysrst_dly in seconds
-	 */
-	if (sysrst_cnt >= SYSRST_CNT_1SEC_VAL * sysrst_dly)
-		kw_sysrst_action();
-}
-
-#if defined(CONFIG_DISPLAY_CPUINFO)
-int print_cpuinfo(void)
-{
-	char *name = "Unknown";
-
-	switch (readl(KW_REG_DEVICE_ID) & 0x03) {
-	case 1:
-		name = "88F6192_A0";
-		break;
-	case 2:
-		name = "88F6281_A0";
-		break;
-	default:
-		printf("SoC:   Unsupported Kirkwood\n");
-		return -1;
-	}
-	printf("SoC:   Kirkwood %s\n", name);
-	return 0;
-}
-#endif /* CONFIG_DISPLAY_CPUINFO */
-
-#ifdef CONFIG_ARCH_CPU_INIT
-int arch_cpu_init(void)
-{
-	u32 reg;
-	struct kwcpu_registers *cpureg =
-		(struct kwcpu_registers *)KW_CPU_REG_BASE;
-
-	/* Linux expects` the internal registers to be at 0xf1000000 */
-	writel(KW_REGS_PHY_BASE, KW_OFFSET_REG);
-
-	/* Enable and invalidate L2 cache in write through mode */
-	writel(readl(&cpureg->l2_cfg) | 0x18, &cpureg->l2_cfg);
-	invalidate_l2_cache();
-
-	kw_config_adr_windows();
-
-#ifdef CONFIG_KIRKWOOD_RGMII_PAD_1V8
-	/*
-	 * Configures the I/O voltage of the pads connected to Egigabit
-	 * Ethernet interface to 1.8V
-	 * By defult it is set to 3.3V
-	 */
-	reg = readl(KW_REG_MPP_OUT_DRV_REG);
-	reg |= (1 << 7);
-	writel(reg, KW_REG_MPP_OUT_DRV_REG);
-#endif
-#ifdef CONFIG_KIRKWOOD_EGIGA_INIT
-	/*
-	 * Set egiga port0/1 in normal functional mode
-	 * This is required becasue on kirkwood by default ports are in reset mode
-	 * OS egiga driver may not have provision to set them in normal mode
-	 * and if u-boot is build without network support, network may fail at OS level
-	 */
-	reg = readl(KWGBE_PORT_SERIAL_CONTROL1_REG(0));
-	reg &= ~(1 << 4);	/* Clear PortReset Bit */
-	writel(reg, (KWGBE_PORT_SERIAL_CONTROL1_REG(0)));
-	reg = readl(KWGBE_PORT_SERIAL_CONTROL1_REG(1));
-	reg &= ~(1 << 4);	/* Clear PortReset Bit */
-	writel(reg, (KWGBE_PORT_SERIAL_CONTROL1_REG(1)));
-#endif
-#ifdef CONFIG_KIRKWOOD_PCIE_INIT
-	/*
-	 * Enable PCI Express Port0
-	 */
-	reg = readl(&cpureg->ctrl_stat);
-	reg |= (1 << 0);	/* Set PEX0En Bit */
-	writel(reg, &cpureg->ctrl_stat);
-#endif
-	return 0;
-}
-#endif /* CONFIG_ARCH_CPU_INIT */
-
-/*
- * SOC specific misc init
- */
-#if defined(CONFIG_ARCH_MISC_INIT)
-int arch_misc_init(void)
-{
-	volatile u32 temp;
-
-	/*CPU streaming & write allocate */
-	temp = readfr_extra_feature_reg();
-	temp &= ~(1 << 28);	/* disable wr alloc */
-	writefr_extra_feature_reg(temp);
-
-	temp = readfr_extra_feature_reg();
-	temp &= ~(1 << 29);	/* streaming disabled */
-	writefr_extra_feature_reg(temp);
-
-	/* L2Cache settings */
-	temp = readfr_extra_feature_reg();
-	/* Disable L2C pre fetch - Set bit 24 */
-	temp |= (1 << 24);
-	/* enable L2C - Set bit 22 */
-	temp |= (1 << 22);
-	writefr_extra_feature_reg(temp);
-
-	icache_enable();
-	/* Change reset vector to address 0x0 */
-	temp = get_cr();
-	set_cr(temp & ~CR_V);
-
-	/* checks and execute resset to factory event */
-	kw_sysrst_check();
-
-	return 0;
-}
-#endif /* CONFIG_ARCH_MISC_INIT */
-
-#ifdef CONFIG_KIRKWOOD_EGIGA
-int cpu_eth_init(bd_t *bis)
-{
-	kirkwood_egiga_initialize(bis);
-	return 0;
-}
-#endif