diff options
Diffstat (limited to 'u-boot/board/bf548-ezkit/video.c')
| -rw-r--r-- | u-boot/board/bf548-ezkit/video.c | 333 |
1 files changed, 333 insertions, 0 deletions
diff --git a/u-boot/board/bf548-ezkit/video.c b/u-boot/board/bf548-ezkit/video.c new file mode 100644 index 0000000..9bcf935 --- /dev/null +++ b/u-boot/board/bf548-ezkit/video.c @@ -0,0 +1,333 @@ +/* + * video.c - run splash screen on lcd + * + * Copyright (c) 2007-2008 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include <stdarg.h> +#include <common.h> +#include <config.h> +#include <malloc.h> +#include <asm/blackfin.h> +#include <asm/gpio.h> +#include <asm/portmux.h> +#include <asm/mach-common/bits/dma.h> +#include <i2c.h> +#include <linux/types.h> +#include <stdio_dev.h> + +#define DMA_SIZE16 2 + +#include <asm/mach-common/bits/eppi.h> + +#include <asm/bfin_logo_230x230.h> + +#define LCD_X_RES 480 /*Horizontal Resolution */ +#define LCD_Y_RES 272 /* Vertical Resolution */ + +#define LCD_BPP 24 /* Bit Per Pixel */ +#define LCD_PIXEL_SIZE (LCD_BPP / 8) +#define DMA_BUS_SIZE 32 +#define ACTIVE_VIDEO_MEM_OFFSET 0 + +/* -- Horizontal synchronizing -- + * + * Timing characteristics taken from the SHARP LQ043T1DG01 datasheet + * (LCY-W-06602A Page 9 of 22) + * + * Clock Frequency 1/Tc Min 7.83 Typ 9.00 Max 9.26 MHz + * + * Period TH - 525 - Clock + * Pulse width THp - 41 - Clock + * Horizontal period THd - 480 - Clock + * Back porch THb - 2 - Clock + * Front porch THf - 2 - Clock + * + * -- Vertical synchronizing -- + * Period TV - 286 - Line + * Pulse width TVp - 10 - Line + * Vertical period TVd - 272 - Line + * Back porch TVb - 2 - Line + * Front porch TVf - 2 - Line + */ + +#define LCD_CLK (8*1000*1000) /* 8MHz */ + +/* # active data to transfer after Horizontal Delay clock */ +#define EPPI_HCOUNT LCD_X_RES + +/* # active lines to transfer after Vertical Delay clock */ +#define EPPI_VCOUNT LCD_Y_RES + +/* Samples per Line = 480 (active data) + 45 (padding) */ +#define EPPI_LINE 525 + +/* Lines per Frame = 272 (active data) + 14 (padding) */ +#define EPPI_FRAME 286 + +/* FS1 (Hsync) Width (Typical)*/ +#define EPPI_FS1W_HBL 41 + +/* FS1 (Hsync) Period (Typical) */ +#define EPPI_FS1P_AVPL EPPI_LINE + +/* Horizontal Delay clock after assertion of Hsync (Typical) */ +#define EPPI_HDELAY 43 + +/* FS2 (Vsync) Width = FS1 (Hsync) Period * 10 */ +#define EPPI_FS2W_LVB (EPPI_LINE * 10) + + /* FS2 (Vsync) Period = FS1 (Hsync) Period * Lines per Frame */ +#define EPPI_FS2P_LAVF (EPPI_LINE * EPPI_FRAME) + +/* Vertical Delay after assertion of Vsync (2 Lines) */ +#define EPPI_VDELAY 12 + +#define EPPI_CLIP 0xFF00FF00 + +/* EPPI Control register configuration value for RGB out + * - EPPI as Output + * GP 2 frame sync mode, + * Internal Clock generation disabled, Internal FS generation enabled, + * Receives samples on EPPI_CLK raising edge, Transmits samples on EPPI_CLK falling edge, + * FS1 & FS2 are active high, + * DLEN = 6 (24 bits for RGB888 out) or 5 (18 bits for RGB666 out) + * DMA Unpacking disabled when RGB Formating is enabled, otherwise DMA unpacking enabled + * Swapping Enabled, + * One (DMA) Channel Mode, + * RGB Formatting Enabled for RGB666 output, disabled for RGB888 output + * Regular watermark - when FIFO is 100% full, + * Urgent watermark - when FIFO is 75% full + */ + +#define EPPI_CONTROL (0x20136E2E) + +static inline u16 get_eppi_clkdiv(u32 target_ppi_clk) +{ + u32 sclk = get_sclk(); + + /* EPPI_CLK = (SCLK) / (2 * (EPPI_CLKDIV[15:0] + 1)) */ + + return (((sclk / target_ppi_clk) / 2) - 1); +} + +void Init_PPI(void) +{ + u16 eppi_clkdiv = get_eppi_clkdiv(LCD_CLK); + + bfin_write_EPPI0_FS1W_HBL(EPPI_FS1W_HBL); + bfin_write_EPPI0_FS1P_AVPL(EPPI_FS1P_AVPL); + bfin_write_EPPI0_FS2W_LVB(EPPI_FS2W_LVB); + bfin_write_EPPI0_FS2P_LAVF(EPPI_FS2P_LAVF); + bfin_write_EPPI0_CLIP(EPPI_CLIP); + + bfin_write_EPPI0_FRAME(EPPI_FRAME); + bfin_write_EPPI0_LINE(EPPI_LINE); + + bfin_write_EPPI0_HCOUNT(EPPI_HCOUNT); + bfin_write_EPPI0_HDELAY(EPPI_HDELAY); + bfin_write_EPPI0_VCOUNT(EPPI_VCOUNT); + bfin_write_EPPI0_VDELAY(EPPI_VDELAY); + + bfin_write_EPPI0_CLKDIV(eppi_clkdiv); + +/* + * DLEN = 6 (24 bits for RGB888 out) or 5 (18 bits for RGB666 out) + * RGB Formatting Enabled for RGB666 output, disabled for RGB888 output + */ +#if defined(CONFIG_VIDEO_RGB666) + bfin_write_EPPI0_CONTROL((EPPI_CONTROL & ~DLENGTH) | DLEN_18 | + RGB_FMT_EN); +#else + bfin_write_EPPI0_CONTROL(((EPPI_CONTROL & ~DLENGTH) | DLEN_24) & + ~RGB_FMT_EN); +#endif + +} + +#define DEB2_URGENT 0x2000 /* DEB2 Urgent */ + +void Init_DMA(void *dst) +{ + +#if defined(CONFIG_DEB_DMA_URGENT) + bfin_write_EBIU_DDRQUE(bfin_read_EBIU_DDRQUE() | DEB2_URGENT); +#endif + + bfin_write_DMA12_START_ADDR(dst); + + /* X count */ + bfin_write_DMA12_X_COUNT((LCD_X_RES * LCD_BPP) / DMA_BUS_SIZE); + bfin_write_DMA12_X_MODIFY(DMA_BUS_SIZE / 8); + + /* Y count */ + bfin_write_DMA12_Y_COUNT(LCD_Y_RES); + bfin_write_DMA12_Y_MODIFY(DMA_BUS_SIZE / 8); + + /* DMA Config */ + bfin_write_DMA12_CONFIG( + WDSIZE_32 | /* 32 bit DMA */ + DMA2D | /* 2D DMA */ + FLOW_AUTO /* autobuffer mode */ + ); +} + +void Init_Ports(void) +{ + const unsigned short pins[] = { + P_PPI0_D0, P_PPI0_D1, P_PPI0_D2, P_PPI0_D3, P_PPI0_D4, + P_PPI0_D5, P_PPI0_D6, P_PPI0_D7, P_PPI0_D8, P_PPI0_D9, + P_PPI0_D10, P_PPI0_D11, P_PPI0_D12, P_PPI0_D13, P_PPI0_D14, + P_PPI0_D15, P_PPI0_D16, P_PPI0_D17, +#if !defined(CONFIG_VIDEO_RGB666) + P_PPI0_D18, P_PPI0_D19, P_PPI0_D20, P_PPI0_D21, P_PPI0_D22, + P_PPI0_D23, +#endif + P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2, 0, + }; + peripheral_request_list(pins, "lcd"); + + gpio_request(GPIO_PE3, "lcd-disp"); + gpio_direction_output(GPIO_PE3, 1); +} + +void EnableDMA(void) +{ + bfin_write_DMA12_CONFIG(bfin_read_DMA12_CONFIG() | DMAEN); +} + +void DisableDMA(void) +{ + bfin_write_DMA12_CONFIG(bfin_read_DMA12_CONFIG() & ~DMAEN); +} + +/* enable and disable PPI functions */ +void EnablePPI(void) +{ + bfin_write_EPPI0_CONTROL(bfin_read_EPPI0_CONTROL() | EPPI_EN); +} + +void DisablePPI(void) +{ + bfin_write_EPPI0_CONTROL(bfin_read_EPPI0_CONTROL() & ~EPPI_EN); +} + +int video_init(void *dst) +{ + Init_Ports(); + Init_DMA(dst); + EnableDMA(); + Init_PPI(); + EnablePPI(); + + return 0; +} + +void video_stop(void) +{ + DisablePPI(); + DisableDMA(); +} + +static void dma_bitblit(void *dst, fastimage_t *logo, int x, int y) +{ + if (dcache_status()) + blackfin_dcache_flush_range(logo->data, logo->data + logo->size); + + bfin_write_MDMA_D0_IRQ_STATUS(DMA_DONE | DMA_ERR); + + /* Setup destination start address */ + bfin_write_MDMA_D0_START_ADDR(dst + ((x & -2) * LCD_PIXEL_SIZE) + + (y * LCD_X_RES * LCD_PIXEL_SIZE)); + /* Setup destination xcount */ + bfin_write_MDMA_D0_X_COUNT(logo->width * LCD_PIXEL_SIZE / DMA_SIZE16); + /* Setup destination xmodify */ + bfin_write_MDMA_D0_X_MODIFY(DMA_SIZE16); + + /* Setup destination ycount */ + bfin_write_MDMA_D0_Y_COUNT(logo->height); + /* Setup destination ymodify */ + bfin_write_MDMA_D0_Y_MODIFY((LCD_X_RES - logo->width) * LCD_PIXEL_SIZE + DMA_SIZE16); + + + /* Setup Source start address */ + bfin_write_MDMA_S0_START_ADDR(logo->data); + /* Setup Source xcount */ + bfin_write_MDMA_S0_X_COUNT(logo->width * LCD_PIXEL_SIZE / DMA_SIZE16); + /* Setup Source xmodify */ + bfin_write_MDMA_S0_X_MODIFY(DMA_SIZE16); + + /* Setup Source ycount */ + bfin_write_MDMA_S0_Y_COUNT(logo->height); + /* Setup Source ymodify */ + bfin_write_MDMA_S0_Y_MODIFY(DMA_SIZE16); + + + /* Enable source DMA */ + bfin_write_MDMA_S0_CONFIG(DMAEN | WDSIZE_16 | DMA2D); + SSYNC(); + bfin_write_MDMA_D0_CONFIG(WNR | DMAEN | WDSIZE_16 | DMA2D); + + while (bfin_read_MDMA_D0_IRQ_STATUS() & DMA_RUN); + + bfin_write_MDMA_S0_IRQ_STATUS(bfin_read_MDMA_S0_IRQ_STATUS() | DMA_DONE | DMA_ERR); + bfin_write_MDMA_D0_IRQ_STATUS(bfin_read_MDMA_D0_IRQ_STATUS() | DMA_DONE | DMA_ERR); + +} + +void video_putc(const char c) +{ +} + +void video_puts(const char *s) +{ +} + +int drv_video_init(void) +{ + int error, devices = 1; + struct stdio_dev videodev; + + u8 *dst; + u32 fbmem_size = LCD_X_RES * LCD_Y_RES * LCD_PIXEL_SIZE + ACTIVE_VIDEO_MEM_OFFSET; + + dst = malloc(fbmem_size); + + if (dst == NULL) { + printf("Failed to alloc FB memory\n"); + return -1; + } + +#ifdef EASYLOGO_ENABLE_GZIP + unsigned char *data = EASYLOGO_DECOMP_BUFFER; + unsigned long src_len = EASYLOGO_ENABLE_GZIP; + if (gunzip(data, bfin_logo.size, bfin_logo.data, &src_len)) { + puts("Failed to decompress logo\n"); + free(dst); + return -1; + } + bfin_logo.data = data; +#endif + + memset(dst + ACTIVE_VIDEO_MEM_OFFSET, bfin_logo.data[0], fbmem_size - ACTIVE_VIDEO_MEM_OFFSET); + + dma_bitblit(dst + ACTIVE_VIDEO_MEM_OFFSET, &bfin_logo, + (LCD_X_RES - bfin_logo.width) / 2, + (LCD_Y_RES - bfin_logo.height) / 2); + + video_init(dst); /* Video initialization */ + + memset(&videodev, 0, sizeof(videodev)); + + strcpy(videodev.name, "video"); + videodev.ext = DEV_EXT_VIDEO; /* Video extensions */ + videodev.flags = DEV_FLAGS_SYSTEM; /* No Output */ + videodev.putc = video_putc; /* 'putc' function */ + videodev.puts = video_puts; /* 'puts' function */ + + error = stdio_register(&videodev); + + return (error == 0) ? devices : error; +} |