diff options
Diffstat (limited to 'u-boot/include/configs/TQM85xx.h')
| -rw-r--r-- | u-boot/include/configs/TQM85xx.h | 701 |
1 files changed, 701 insertions, 0 deletions
diff --git a/u-boot/include/configs/TQM85xx.h b/u-boot/include/configs/TQM85xx.h new file mode 100644 index 0000000..79a958d --- /dev/null +++ b/u-boot/include/configs/TQM85xx.h @@ -0,0 +1,701 @@ +/* + * (C) Copyright 2007 + * Thomas Waehner, TQ-System GmbH, thomas.waehner@tqs.de. + * + * (C) Copyright 2005 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * Wolfgang Denk <wd@denx.de> + * Copyright 2004 Freescale Semiconductor. + * (C) Copyright 2002,2003 Motorola,Inc. + * Xianghua Xiao <X.Xiao@motorola.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * TQM85xx (8560/40/55/41/48) board configuration file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */ + +#if defined(CONFIG_TQM8548_BE) +#define CONFIG_SYS_TEXT_BASE 0xfff80000 +#else +#define CONFIG_SYS_TEXT_BASE 0xfffc0000 +#endif + +#if defined(CONFIG_TQM8548_AG) || defined(CONFIG_TQM8548_BE) +#define CONFIG_TQM8548 +#endif + +#define CONFIG_PCI +#ifndef CONFIG_TQM8548_AG +#define CONFIG_PCI1 /* PCI/PCI-X controller */ +#endif +#ifdef CONFIG_TQM8548 +#define CONFIG_PCIE1 /* PCI Express interface */ +#endif + +#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ +#define CONFIG_PCIX_CHECK /* PCIX olny works at 66 MHz */ +#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ + +#define CONFIG_TSEC_ENET /* tsec ethernet support */ + +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ + + /* + * Configuration for big NOR Flashes + * + * Define CONFIG_TQM_BIGFLASH for boards with more than 128 MiB NOR Flash. + * Please be aware, that this changes the whole memory map (new CCSRBAR + * address, etc). You have to use an adapted Linux kernel or FDT blob + * if this option is set. + */ +#undef CONFIG_TQM_BIGFLASH + +/* + * NAND flash support (disabled by default) + * + * Warning: NAND support will likely increase the U-Boot image size + * to more than 256 KB. Please adjust CONFIG_SYS_TEXT_BASE if necessary. + */ +#ifdef CONFIG_TQM8548_BE +#define CONFIG_NAND +#endif + +/* + * MPC8540 and MPC8548 don't have CPM module + */ +#if !defined(CONFIG_MPC8540) && !defined(CONFIG_MPC8548) +#define CONFIG_CPM2 1 /* has CPM2 */ +#endif + +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ + +#if defined(CONFIG_TQM8548_AG) || defined(CONFIG_TQM8548_BE) +#define CONFIG_CAN_DRIVER /* CAN Driver support */ +#endif + +/* + * sysclk for MPC85xx + * + * Two valid values are: + * 33333333 + * 66666666 + * + * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz + * is likely the desired value here, so that is now the default. + * The board, however, can run at 66MHz. In any event, this value + * must match the settings of some switches. Details can be found + * in the README.mpc85xxads. + */ + +#ifndef CONFIG_SYS_CLK_FREQ +#define CONFIG_SYS_CLK_FREQ 33333333 +#endif + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ + +#define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ + +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00000000 +#define CONFIG_SYS_MEMTEST_END 0x10000000 + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ +#ifdef CONFIG_TQM_BIGFLASH +#define CONFIG_SYS_CCSRBAR 0xA0000000 /* relocated CCSRBAR */ +#else /* !CONFIG_TQM_BIGFLASH */ +#define CONFIG_SYS_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ +#endif /* CONFIG_TQM_BIGFLASH */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ + +/* + * DDR Setup + */ +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ +#if defined(CONFIG_TQM_BIGFLASH) || \ + (!defined(CONFIG_TQM8548_AG) && !defined(CONFIG_TQM8548_BE)) +#define CONFIG_SYS_PPC_DDR_WIMGE (MAS2_I | MAS2_G) +#endif +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#ifdef CONFIG_TQM8548_AG +#define CONFIG_VERY_BIG_RAM +#endif + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 + +#if defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560) +/* TQM8540 & 8560 need DLL-override */ +#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN /* possible DLL fix needed */ +#define CONFIG_DDR_DEFAULT_CL 25 /* CAS latency 2,5 */ +#endif /* CONFIG_TQM8540 || CONFIG_TQM8560 */ + +#if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) || \ + defined(CONFIG_TQM8548) +#define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */ +#endif /* CONFIG_TQM8541 || CONFIG_TQM8555 || CONFIG_TQM8548 */ + +/* + * Flash on the Local Bus + */ +#ifdef CONFIG_TQM_BIGFLASH +#define CONFIG_SYS_FLASH0 0xE0000000 +#define CONFIG_SYS_FLASH1 0xC0000000 +#else /* !CONFIG_TQM_BIGFLASH */ +#define CONFIG_SYS_FLASH0 0xFC000000 +#define CONFIG_SYS_FLASH1 0xF8000000 +#endif /* CONFIG_TQM_BIGFLASH */ +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } + +#define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH1 /* Localbus flash start */ +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH */ + +/* Default ORx timings are for <= 41.7 MHz Local Bus Clock. + * + * Note: According to timing specifications external addr latch delay + * (EAD, bit #0) must be set if Local Bus Clock is > 83 MHz. + * + * For other Local Bus Clocks see following table: + * + * Clock/MHz CONFIG_SYS_ORx_PRELIM + * 166 0x.....CA5 + * 133 0x.....C85 + * 100 0x.....C65 + * 83 0x.....FA2 + * 66 0x.....C82 + * 50 0x.....C60 + * 42 0x.....040 + * 33 0x.....030 + * 25 0x.....020 + * + */ +#ifdef CONFIG_TQM_BIGFLASH +#define CONFIG_SYS_BR0_PRELIM 0xE0001801 /* port size 32bit */ +#define CONFIG_SYS_OR0_PRELIM 0xE0000040 /* 512MB Flash */ +#define CONFIG_SYS_BR1_PRELIM 0xC0001801 /* port size 32bit */ +#define CONFIG_SYS_OR1_PRELIM 0xE0000040 /* 512MB Flash */ +#else /* !CONFIG_TQM_BIGFLASH */ +#define CONFIG_SYS_BR0_PRELIM 0xfc001801 /* port size 32bit */ +#define CONFIG_SYS_OR0_PRELIM 0xfc000040 /* 64MB Flash */ +#define CONFIG_SYS_BR1_PRELIM 0xf8001801 /* port size 32bit */ +#define CONFIG_SYS_OR1_PRELIM 0xfc000040 /* 64MB Flash */ +#endif /* CONFIG_TQM_BIGFLASH */ + +#define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */ +#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector */ +#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* speed up output to Flash */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +/* + * Note: when changing the Local Bus clock divider you have to + * change the timing values in CONFIG_SYS_ORx_PRELIM. + * + * LCRR[00:03] CLKDIV: System (CCB) clock divider. Valid values are 2, 4, 8. + * LCRR[16:17] EADC : External address delay cycles. It should be set to 2 + * for Local Bus Clock > 83.3 MHz. + */ +#define CONFIG_SYS_LBC_LCRR 0x00030008 /* LB clock ratio reg */ +#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ +#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ +#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_CCSRBAR \ + + 0x04010000) /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (~CONFIG_SYS_TEXT_BASE + 1)/* Reserved for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (384 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#if defined(CONFIG_TQM8560) + +#define CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ + +#else /* !CONFIG_TQM8560 */ + +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) + +/* PS/2 Keyboard */ +#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */ +#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */ +#define CONFIG_PS2SERIAL 2 /* .. on DUART2 */ +#define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */ +#define CONFIG_BOARD_EARLY_INIT_R 1 + +#endif /* CONFIG_TQM8560 */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ +#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +/* CAN */ +#define CONFIG_SYS_CAN_BASE (CONFIG_SYS_CCSRBAR \ + + 0x03000000) /* CAN base address */ +#ifdef CONFIG_CAN_DRIVER +#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 KiB address mask */ +#define CONFIG_SYS_OR2_CAN (CONFIG_SYS_CAN_OR_AM | OR_UPM_BI) +#define CONFIG_SYS_BR2_CAN ((CONFIG_SYS_CAN_BASE & BR_BA) | \ + BR_PS_8 | BR_MS_UPMC | BR_V) +#endif /* CONFIG_CAN_DRIVER */ + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {0x48} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 + +/* I2C RTC */ +#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* I2C EEPROM */ +/* + * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work also). + */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 +#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ + +/* I2C SYSMON (LM75) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ +#define CONFIG_SYS_DTT_MAX_TEMP 70 +#define CONFIG_SYS_DTT_LOW_TEMP -30 +#define CONFIG_SYS_DTT_HYSTERESIS 3 + +#ifndef CONFIG_PCIE1 +/* RapidIO MMU */ +#ifdef CONFIG_TQM_BIGFLASH +#define CONFIG_SYS_RIO_MEM_BASE 0xb0000000 /* base address */ +#define CONFIG_SYS_RIO_MEM_SIZE 0x10000000 /* 256M */ +#else /* !CONFIG_TQM_BIGFLASH */ +#define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 /* base address */ +#define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 512M */ +#endif /* CONFIG_TQM_BIGFLASH */ +#define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE +#endif /* CONFIG_PCIE1 */ + +/* NAND FLASH */ +#ifdef CONFIG_NAND + +#define CONFIG_NAND_FSL_UPM 1 + +#define CONFIG_MTD_NAND_ECC_JFFS2 1 /* use JFFS2 ECC */ + +/* address distance between chip selects */ +#define CONFIG_SYS_NAND_SELECT_DEVICE 1 +#define CONFIG_SYS_NAND_CS_DIST 0x200 + +#define CONFIG_SYS_NAND_SIZE 0x8000 +#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_CCSRBAR + 0x03010000) + +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define CONFIG_SYS_NAND_MAX_CHIPS 2 /* Number of chips per device */ + +/* CS3 for NAND Flash */ +#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_NAND_BASE & BR_BA) | \ + BR_PS_8 | BR_MS_UPMB | BR_V) +#define CONFIG_SYS_OR3_PRELIM (P2SZ_TO_AM(CONFIG_SYS_NAND_SIZE) | OR_UPM_BI) + +#define NAND_BIG_DELAY_US 25 /* max tR for Samsung devices */ + +#endif /* CONFIG_NAND */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS +#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCI1_IO_BUS (CONFIG_SYS_CCSRBAR + 0x02000000) +#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BUS +#define CONFIG_SYS_PCI1_IO_SIZE 0x1000000 /* 16M */ + +#ifdef CONFIG_PCIE1 +/* + * General PCI express + * Addresses are mapped 1-1. + */ +#ifdef CONFIG_TQM_BIGFLASH +#define CONFIG_SYS_PCIE1_MEM_BUS 0xb0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_BUS 0xaf000000 +#else /* !CONFIG_TQM_BIGFLASH */ +#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_BUS 0xef000000 +#endif /* CONFIG_TQM_BIGFLASH */ +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS +#define CONFIG_SYS_PCIE1_IO_PHYS CONFIG_SYS_PCIE1_IO_BUS +#define CONFIG_SYS_PCIE1_IO_SIZE 0x1000000 /* 16M */ +#endif /* CONFIG_PCIE1 */ + +#if defined(CONFIG_PCI) + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#define CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ + +#endif /* CONFIG_PCI */ + +#define CONFIG_NET_MULTI 1 + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "TSEC0" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "TSEC1" +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT +#define FEC_PHY_ADDR 3 +#define FEC_PHYIDX 0 +#define FEC_FLAGS 0 +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#define CONFIG_HAS_ETH2 + +#ifdef CONFIG_TQM8548 +/* + * TQM8548 has 4 ethernet ports. 4 ETSEC's. + * + * On the STK85xx Starterkit the ETSEC3/4 ports are on an + * additional adapter (AIO) between module and Starterkit. + */ +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "TSEC2" +#define CONFIG_TSEC4 1 +#define CONFIG_TSEC4_NAME "TSEC3" +#define TSEC3_PHY_ADDR 4 +#define TSEC4_PHY_ADDR 5 +#define TSEC3_PHYIDX 0 +#define TSEC4_PHYIDX 0 +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define CONFIG_HAS_ETH3 +#define CONFIG_HAS_ETH4 +#endif /* CONFIG_TQM8548 */ + +/* Options are TSEC[0-1], FEC */ +#define CONFIG_ETHPRIME "TSEC0" + +#if defined(CONFIG_TQM8540) +/* + * TQM8540 has 3 ethernet ports. 2 TSEC's and one FEC. + * The FEC port is connected on the same signals as the FCC3 port + * of the TQM8560 to the baseboard (STK85xx Starterkit). + * + * On the STK85xx Starterkit the X47/X50 jumper has to be set to + * a - d (X50.2 - 3) to enable the FEC port. + */ +#define CONFIG_MPC85XX_FEC 1 +#define CONFIG_MPC85XX_FEC_NAME "FEC" +#endif + +#if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) +/* + * TQM8541/55 have 4 ethernet ports. 2 TSEC's and 2 FCC's. Only one FCC port + * can be used at once, since only one FCC port is available on the STK85xx + * Starterkit. + * + * To use this port you have to configure U-Boot to use the FCC port 1...2 + * and set the X47/X50 jumper to: + * FCC1: a - b (X47.2 - X50.2) + * FCC2: a - c (X50.2 - 1) + */ +#define CONFIG_ETHER_ON_FCC +#define CONFIG_ETHER_INDEX 1 /* FCC channel for ethernet */ +#endif + +#if defined(CONFIG_TQM8560) +/* + * TQM8560 has 5 ethernet ports. 2 TSEC's and 3 FCC's. Only one FCC port + * can be used at once, since only one FCC port is available on the STK85xx + * Starterkit. + * + * To use this port you have to configure U-Boot to use the FCC port 1...3 + * and set the X47/X50 jumper to: + * FCC1: a - b (X47.2 - X50.2) + * FCC2: a - c (X50.2 - 1) + * FCC3: a - d (X50.2 - 3) + */ +#define CONFIG_ETHER_ON_FCC +#define CONFIG_ETHER_INDEX 3 /* FCC channel for ethernet */ +#endif + +#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1) +#define CONFIG_ETHER_ON_FCC1 +#define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | \ + CMXFCR_TF1CS_MSK) +#define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12) +#define CONFIG_SYS_CPMFCR_RAMTYPE 0 +#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) +#endif + +#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) +#define CONFIG_ETHER_ON_FCC2 +#define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | \ + CMXFCR_TF2CS_MSK) +#define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK16 | CMXFCR_TF2CS_CLK13) +#define CONFIG_SYS_CPMFCR_RAMTYPE 0 +#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) +#endif + +#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3) +#define CONFIG_ETHER_ON_FCC3 +#define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | \ + CMXFCR_TF3CS_MSK) +#define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14) +#define CONFIG_SYS_CPMFCR_RAMTYPE 0 +#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) +#endif + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_FLASH 1 + +#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K (one sector) for env */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_TIMESTAMP /* Print image info with ts */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +#ifdef CONFIG_NAND +/* + * Use NAND-FLash as JFFS2 device + */ +#define CONFIG_CMD_NAND +#define CONFIG_CMD_JFFS2 + +#define CONFIG_JFFS2_NAND 1 + +#ifdef CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ +#define CONFIG_FLASH_CFI_MTD +#define MTDIDS_DEFAULT "nand0=TQM85xx-nand" +#define MTDPARTS_DEFAULT "mtdparts=TQM85xx-nand:-" +#else +#define CONFIG_JFFS2_DEV "nand0" /* NAND device jffs2 lives on */ +#define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */ +#define CONFIG_JFFS2_PART_SIZE 0x200000 /* size of jffs2 partition */ +#endif /* CONFIG_CMD_MTDPARTS */ + +#endif /* CONFIG_NAND */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NFS +#define CONFIG_CMD_SNTP +#ifndef CONFIG_TQM8548_AG +#define CONFIG_CMD_DATE +#endif +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_DTT +#define CONFIG_CMD_MII +#define CONFIG_CMD_REGINFO + +#if defined(CONFIG_PCI) +#define CONFIG_CMD_PCI +#endif + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buf Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +#define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/ + +#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + + +/* + * Setup some board specific values for the default environment variables + */ +#ifdef CONFIG_CPM2 +#define CONFIG_ENV_CONSDEV "consdev=ttyCPM0\0" +#else +#define CONFIG_ENV_CONSDEV "consdev=ttyS0\0" +#endif +#define CONFIG_ENV_FDT_FILE "fdt_file="MK_STR(CONFIG_HOSTNAME)"/" \ + MK_STR(CONFIG_HOSTNAME)".dtb\0" +#define CONFIG_ENV_BOOTFILE "bootfile="MK_STR(CONFIG_HOSTNAME)"/uImage\0" +#define CONFIG_ENV_UBOOT "uboot="MK_STR(CONFIG_HOSTNAME)"/u-boot.bin\0" \ + "uboot_addr="MK_STR(CONFIG_SYS_TEXT_BASE)"\0" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_ENV_BOOTFILE \ + CONFIG_ENV_FDT_FILE \ + CONFIG_ENV_CONSDEV \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs $bootargs " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask" \ + ":$hostname:$netdev:off panic=1\0" \ + "addcons=setenv bootargs $bootargs " \ + "console=$consdev,$baudrate\0" \ + "flash_nfs=run nfsargs addip addcons;" \ + "bootm $kernel_addr - $fdt_addr\0" \ + "flash_self=run ramargs addip addcons;" \ + "bootm $kernel_addr $ramdisk_addr $fdt_addr\0" \ + "net_nfs=tftp $kernel_addr_r $bootfile;" \ + "tftp $fdt_addr_r $fdt_file;" \ + "run nfsargs addip addcons;" \ + "bootm $kernel_addr_r - $fdt_addr_r\0" \ + "rootpath=/opt/eldk/ppc_85xx\0" \ + "fdt_addr_r=900000\0" \ + "kernel_addr_r=1000000\0" \ + "fdt_addr=ffec0000\0" \ + "kernel_addr=ffd00000\0" \ + "ramdisk_addr=ff800000\0" \ + CONFIG_ENV_UBOOT \ + "load=tftp 100000 $uboot\0" \ + "update=protect off $uboot_addr +$filesize;" \ + "erase $uboot_addr +$filesize;" \ + "cp.b 100000 $uboot_addr $filesize" \ + "upd=run load update\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#endif /* __CONFIG_H */ |