diff options
Diffstat (limited to 'u-boot/include/configs/VOH405.h')
| -rw-r--r-- | u-boot/include/configs/VOH405.h | 429 |
1 files changed, 429 insertions, 0 deletions
diff --git a/u-boot/include/configs/VOH405.h b/u-boot/include/configs/VOH405.h new file mode 100644 index 0000000..f0c0bd9 --- /dev/null +++ b/u-boot/include/configs/VOH405.h @@ -0,0 +1,429 @@ +/* + * (C) Copyright 2001-2003 + * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_405EP 1 /* This is a PPC405 CPU */ +#define CONFIG_4xx 1 /* ...member of PPC4xx family */ +#define CONFIG_VOH405 1 /* ...on a VOH405 board */ + +#define CONFIG_SYS_TEXT_BASE 0xFFF80000 + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ +#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ + +#define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */ + +#define CONFIG_BAUDRATE 9600 +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ + +#undef CONFIG_BOOTARGS +#undef CONFIG_BOOTCOMMAND + +#define CONFIG_PREBOOT /* enable preboot variable */ + +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_NET_MULTI 1 +#undef CONFIG_HAS_ETH1 + +#define CONFIG_PPC4xx_EMAC +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0 /* PHY address */ +#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ + +#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/ + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PCI +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_IDE +#define CONFIG_CMD_FAT +#define CONFIG_CMD_ELF +#define CONFIG_CMD_NAND +#define CONFIG_CMD_DATE +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_EEPROM + + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_SUPPORT_VFAT + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/ +#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */ + +#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ + +#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#endif + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ + +#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ + +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ + +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ +#define CONFIG_SYS_BASE_BAUD 691200 + +/* The following table includes the supported baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE \ + { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ + 57600, 115200, 230400, 460800, 921600 } + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ + +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ + +/*----------------------------------------------------------------------- + * NAND-FLASH stuff + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_BIG_DELAY_US 25 + +#define CONFIG_SYS_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ +#define CONFIG_SYS_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ +#define CONFIG_SYS_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ +#define CONFIG_SYS_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ + +#define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ +#define CONFIG_SYS_NAND_QUIET 1 + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + /* resource configuration */ + +#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ + +#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/ + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ +#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ +#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ +#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ +#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ +#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ + +/*----------------------------------------------------------------------- + * IDE/ATA stuff + *----------------------------------------------------------------------- + */ +#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ +#undef CONFIG_IDE_LED /* no led for ide supported */ +#define CONFIG_IDE_RESET 1 /* reset for ide supported */ + +#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */ +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */ + +#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_IDE1_OFFSET 0x0010 + +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ +#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ +#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ +/* + * The following defines are added for buggy IOP480 byte interface. + * All other boards should use the standard values (CPCI405 etc.) + */ +#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ +#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ +#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xFFF80000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (2 * 1024*1024) /* Reserve 2 MB for malloc() */ + +#if (CONFIG_SYS_MONITOR_BASE < FLASH_BASE0_PRELIM) +# define CONFIG_SYS_RAMBOOT 1 +#else +# undef CONFIG_SYS_RAMBOOT +#endif + +/*----------------------------------------------------------------------- + * Environment Variable setup + */ +#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CONFIG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */ +#define CONFIG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/ + /* total size of a CAT24WC16 is 2048 bytes */ + +#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */ +#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */ + +/*----------------------------------------------------------------------- + * I2C EEPROM (CAT24WC16) for environment + */ +#define CONFIG_HARD_I2C /* I2c with hardware support */ +#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ +#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */ +#define CONFIG_SYS_EEPROM_WREN 1 + +/* CAT24WC32/64... */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */ + /* 32 byte page write mode using*/ + /* last 5 bits of the address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + */ + +#define CAN_BA 0xF0000000 /* CAN Base Address */ +#define DUART0_BA 0xF0000400 /* DUART Base Address */ +#define DUART1_BA 0xF0000408 /* DUART Base Address */ +#define RTC_BA 0xF0000500 /* RTC Base Address */ +#define VGA_BA 0xF1000000 /* Epson VGA Base Address */ +#define CONFIG_SYS_NAND_BASE 0xF4000000 /* NAND FLASH Base Address */ + +/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ +#define CONFIG_SYS_EBC_PB0AP 0x92015480 +/*#define CONFIG_SYS_EBC_PB0AP 0x08055880 /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */ +#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ + +/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */ +#define CONFIG_SYS_EBC_PB1AP 0x92015480 +#define CONFIG_SYS_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */ + +/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */ +#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ + +/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */ +#define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CONFIG_SYS_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ + +/* Memory Bank 4 (Epson VGA) initialization */ +#define CONFIG_SYS_EBC_PB4AP 0x03805380 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=0 */ +#define CONFIG_SYS_EBC_PB4CR VGA_BA | 0x7A000 /* BAS=0xF10,BS=8MB,BU=R/W,BW=16bit */ + +/*----------------------------------------------------------------------- + * LCD Setup + */ + +#define CONFIG_SYS_LCD_BIG_MEM 0xF1200000 /* Epson S1D13806 Mem Base Address */ +#define CONFIG_SYS_LCD_BIG_REG 0xF1000000 /* Epson S1D13806 Reg Base Address */ +#define CONFIG_SYS_LCD_SMALL_MEM 0xF1400000 /* Epson S1D13704 Mem Base Address */ +#define CONFIG_SYS_LCD_SMALL_REG 0xF140FFE0 /* Epson S1D13704 Reg Base Address */ + +#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (1 << 20) + +/*----------------------------------------------------------------------- + * FPGA stuff + */ + +#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100 /* FPGA internal Base Address */ + +/* FPGA internal regs */ +#define CONFIG_SYS_FPGA_CTRL 0x000 + +/* FPGA Control Reg */ +#define CONFIG_SYS_FPGA_CTRL_CF_RESET 0x0001 +#define CONFIG_SYS_FPGA_CTRL_WDI 0x0002 +#define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020 + +#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ +#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/ + +/* FPGA program pin configuration */ +#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ +#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ +#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ +#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ +#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in data cache) + */ +/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ +#define CONFIG_SYS_TEMP_STACK_OCM 1 + +/* On Chip Memory location */ +#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ +#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Definitions for GPIO setup (PPC405EP specific) + * + * GPIO0[0] - External Bus Controller BLAST output + * GPIO0[1-9] - Instruction trace outputs -> GPIO + * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs + * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO + * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs + * GPIO0[24-27] - UART0 control signal inputs/outputs + * GPIO0[28-29] - UART1 data signal input/output + * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs -> GPIO + */ +#define CONFIG_SYS_GPIO0_OSRL 0x00000550 +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 +#define CONFIG_SYS_GPIO0_ISR1H 0x15555440 +#define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_TCR 0x777E0017 + +#define CONFIG_SYS_DUART_RST (0x80000000 >> 14) +#define CONFIG_SYS_LCD_ENDIAN (0x80000000 >> 7) +#define CONFIG_SYS_IIC_ON (0x80000000 >> 8) +#define CONFIG_SYS_LCD0_RST (0x80000000 >> 30) +#define CONFIG_SYS_LCD1_RST (0x80000000 >> 31) +#define CONFIG_SYS_EEPROM_WP (0x80000000 >> 0) + +/* + * Default speed selection (cpu_plb_opb_ebc) in mhz. + * This value will be set if iic boot eprom is disabled. + */ +#if 1 +#define PLLMR0_DEFAULT PLLMR0_266_133_66_33 +#define PLLMR1_DEFAULT PLLMR1_266_133_66_33 +#endif +#if 0 +#define PLLMR0_DEFAULT PLLMR0_200_100_50_33 +#define PLLMR1_DEFAULT PLLMR1_200_100_50_33 +#endif +#if 0 +#define PLLMR0_DEFAULT PLLMR0_133_66_66_33 +#define PLLMR1_DEFAULT PLLMR1_133_66_66_33 +#endif + +#endif /* __CONFIG_H */ |