summaryrefslogtreecommitdiffstats
path: root/MAKEALL
Commit message (Collapse)AuthorAgeFilesLines
...
| * imx27lite: add support for imx27lite board from LogicPDIlya Yanok2009-09-011-0/+1
| | | | | | | | | | | | | | | | | | This patch adds support for i.MX27-LITEKIT development board from LogicPD. This board uses i.MX27 SoC and has 2MB NOR flash, 64MB NAND flash, FEC ethernet controller integrated into i.MX27. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Acked-by: Wolfgang Denk <wd@denx.de>
* | Blackfin: cm-bf537u: new board portHarald Krapfenbauer2009-09-021-0/+1
|/ | | | | | | | The CM-BF537U is similar to the CM-BF537E module, but enough to need its own board port. Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 85xx: Added support for P1011RDB and P2010RDBPoonam Aggrwal2009-08-281-0/+2
| | | | | | | | P1011 and P2010 are single core variants of P1010 and P2020 respectively. The board(RDB) will be same. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: P1020RDB Support AddedPoonam Aggrwal2009-08-281-0/+1
| | | | | Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Add support for P2020RDB boardPoonam Aggrwal2009-08-281-0/+1
| | | | | | | | | | | | | The code base adds P1 & P2 RDB platforms support. The folder and file names can cater to future SOCs of P1/P2 family. P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series. Tested following on P2020RDB: 1. eTSECs 2. DDR, NAND, NOR, I2C. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Add support for the galaxy5200Eric Millbrandt2009-08-251-0/+1
| | | | | | | | | Add support for the DEKA Research and Development galaxy5200 board The galaxy5200 is an Freescale mpc5200 based embedded industrial control board. Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
* Merge branch 'next' of git://git.denx.de/u-boot-coldfireWolfgang Denk2009-08-041-0/+1
|\
| * ColdFire: Add M5208EVB and MCF520x CPU supportTsiChung Liew2009-07-141-0/+1
| | | | | | | | Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk2009-07-291-0/+2
|\ \
| * | ppc4xx: Add GDsys CompactCenter board support.Dirk Eibach2009-07-281-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Board support for the Guntermann & Drunck CompactCenter and DevCon-Center. Based on the AMCC Canyonlands board support by Stefan Roese. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
* | | mpc83xx: Add esd VME8349 board supportReinhard Arlt2009-07-271-0/+1
|/ / | | | | | | | | | | | | | | | | | | This patch adds support for the esd VME8349 board equipped with the MPC8349. It's a VME PMC carrier board equipped with the Tundra TSI148 VME-bridge. Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | ppc4xx: Add 405EP based PMC405DE boardMatthias Fuchs2009-07-241-0/+1
| | | | | | | | | | Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
* | xpedite1k: Move to X-ES vendor directoryPeter Tyser2009-07-241-1/+1
| | | | | | | | | | | | | | | | | | | | The XPedite1000 is an X-ES product thus it can be put in board/xes along with other X-ES boards. Along with the move, the board was renamed to XPedite1000 from XPedite1K to fit X-ES's standard naming convention. Maintainership was also transfered to Peter Tyser. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
* | ppc4xx: Add DL-Vision 405EP board supportDirk Eibach2009-07-241-0/+1
| | | | | | | | | | | | | | Board support for the Guntermann & Drunck DL-Vision. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
* | Marvell RD6281A Board supportPrafulla Wadaskar2009-07-231-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | This is Marvell's 88F6281_A0 based reference design board This patch is tested for- 1. Boot from DRAM/NAND flash/NFS 2. File transfer using tftp and loadb 3. NAND flash read/write/erase Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* | Marvell MV88F6281GTW_GE Board supportPrafulla Wadaskar2009-07-181-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is Marvell's 88F6281_A0 based custom board developed for wireless access point product This patch is tested for- 1. Boot from DRAM/SPI flash/NFS 2. File transfer using tftp and loadb 3. SPI flash read/write/erase 4. Booting Linux kernel and RFS from SPI flash 5. Boot from USB supported Reviewed-by: Ronen Shitrit <rshitrit@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* | Marvell Sheevaplug Board supportPrafulla Wadaskar2009-07-181-0/+1
|/ | | | | | | | | | | | | | | | | | | Reference: http://plugcomputer.org/ http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support This patch is tested for- 1. Boot from DRAM/NAND flash 2. File transfer using tftp 3. NAND flash read/write/erase 4. Linux kernel and RFS Boot from NAND 5. Enabled USB PHY init for kernel need 6. Boot from USB supported Note: to boot Kirkwood kernel with USB support, you should add "usb start" in the boot sequence Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* Merge branch 'master' of /home/wd/git/u-boot/masterWolfgang Denk2009-07-141-18/+21
|\
| * Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2009-07-131-18/+20
| |\
| | * at91: Introduction of at91sam9g10 SOC.Sedji Gaouaou2009-07-121-1/+2
| | | | | | | | | | | | | | | | | | | | | AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a faster clock speed: 266/133MHz. Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
| | * at91: Introduction of at91sam9g45 SOC.Sedji Gaouaou2009-07-121-18/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz. It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of peripherals. The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES. On the board you can find 2 USART, USB high speed, a 480*272 LG lcd, ethernet, gpio/joystick/buttons. Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
| * | sh: Add support ESPT-GIGA boradNobuhiro Iwamatsu2009-07-111-0/+1
| |/ | | | | | | | | | | | | | | | | | | | | | | ESPT-Giga is SH7763-based reference board. Board support is relatively sparse, presently supporting serial, gigabit ethernet, USB host, and MTD. More information (in Japanese) available at: http://www.cente.jp/product/cente_hard/ESPT-Giga.html Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* | board support patch for phyCORE-MPC5200B-tinyJon Smirl2009-07-101-0/+1
|/ | | | | | | | | | Add support for the Phytec phyCORE-MPC5200B-tiny. Code originally from Pengutronix.de. Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on Timer 0/1 Signed-off-by: Jon Smirl <jonsmirl@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2009-07-071-1/+8
|\ | | | | | | | | | | | | Conflicts: drivers/spi/Makefile Signed-off-by: Wolfgang Denk <wd@denx.de>
| * nhk8815: fix MAKEALLJean-Christophe PLAGNIOL-VILLARD2009-07-061-1/+2
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * MX31: Add NAND SPL boot support to i.MX31 PDK board.Magnus Lilja2009-07-061-0/+1
| | | | | | | | Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
| * xscale: add support for the polaris boardStefano Babic2009-07-061-0/+2
| | | | | | | | | | | | | | The Polaris board is based on the TrizepsIV module of Keith & Koep (http://www.keith-koep.com). Signed-off-by: Stefano Babic <sbabic@denx.de>
| * at91: Add esd gmbh MEESC board supportDaniel Gorsulowski2009-07-061-0/+1
| | | | | | | | | | | | | | This patch adds support for esd gmbh MEESC board. The MEESC is based on an Atmel AT91SAM9263 SoC. Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
| * MX31: Add basic support for Freescale i.MX31 PDK board.Magnus Lilja2009-07-061-0/+1
| | | | | | | | | | | | | | | | | | | | | | Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board). This patch assumes that some other program performs the actual NAND boot. Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com> Acked-by: Fabio Estevam <fabioestevam@yahoo.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * at91: add support for the PM9261 board of Ronetix GmbHIlko Iliev2009-06-211-0/+1
| | | | | | | | | | | | | | | | | | | | The PM9261 board is based on the AT91SAM9261-EK board. Here is the page on Ronetix website: http://www.ronetix.at/starter_kit_9261.html Signed-off-by: Ilko Iliev <iliev@ronetix.at> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* | 86xx: XPedite5170 board supportPeter Tyser2009-07-011-0/+1
|/ | | | | | | | | Initial support for Extreme Engineering Solutions XPedite5170 - a MPC8640-based 3U VPX single board computer with a PMC/XMC site. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Blackfin: ibf-dsp561: new board portHoan Hoang2009-06-141-0/+1
| | | | | Signed-off-by: Hoan Hoang <hnhoan@i-syst.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: blackstamp: new board portMike Frysinger2009-06-141-0/+1
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf537-srv1: new board portMike Frysinger2009-06-141-0/+1
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf537-minotaur: new board portMike Frysinger2009-06-141-0/+1
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf537-pnav: new board portMike Frysinger2009-06-141-0/+1
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: cm-bf527: new board portMike Frysinger2009-06-141-0/+1
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: cm-bf548: new board portMike Frysinger2009-06-141-0/+1
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: tcm-bf537: new board portMike Frysinger2009-06-141-0/+1
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: cm-bf561: new board portMike Frysinger2009-06-141-0/+1
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: cm-bf537e: new board portMike Frysinger2009-06-141-0/+1
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: cm-bf533: new board portMike Frysinger2009-06-141-0/+1
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 85xx: Add P2020DS supportSrikanth Srinivasan2009-06-121-0/+2
| | | | | | | | | | | | | The patch adds support for P2020DS reference platform. DDR3 interface uses hard-coded initialization rather than SPD for now and was tested at 667Mhz. Some PIXIS register definitions and associated code sections need to be fixed. TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all tested under u-boot. Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com> Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc512x: Add esd gmbh mecp5123 board supportStefan Roese2009-06-121-0/+1
| | | | | | | MECP5123 is a MPC5121E based module by esd gmbh. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
* MPC512x: add support for ARIA boardWolfgang Denk2009-06-121-0/+1
| | | | | | | ARIA is a MPC5121E based COM Express module by Dave/DENX. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
* Rename ads5121 board into mpc5121adsWolfgang Denk2009-06-121-1/+1
| | | | | | | | | We rename the board so we use a consistent name in U-Boot and in Linux. Also, we use this opportunity to move the board into the Freecale vendor directory. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
* dm355 evm supportDavid Brownell2009-06-121-0/+1
| | | | | | | | | | | | | | | | | | | | | Initial U-Boot support for the DaVinci DM355 EVM. This is a board from Spectrum Digital. Board docs include schematic and firmware for its microcontroller: http://c6000.spectrumdigital.com/evmdm355/revd/ Most of the DM355 chip is fully documented by TI, the most notable exception being the MPEG/JPEG coprocessor (programmable using codecs available at no cost from TI), which is omitted from its DM335 sibling: http://focus.ti.com/docs/prod/folders/print/tms320dm355.html This version can boot from the on-board DM9000 Ethernet chip, after being loaded (from NAND, MMC/SD, or UART). In the near future, NAND and USB support could be added ... NAND support is being held back until the support for the 4-bit ECC hardware is ready. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ZOOM2 Add initial support for Zoom2Tom Rix2009-06-121-0/+1
| | | | | | | | | | | | | | | | | | | | | Zoom2 is a new board from Texas Instruments and LogicPD The logicpd web site is a good source for general information on this board. Please start looking here if the below links are broken. http://www.logicpd.com This is a pdf of the product http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf This is the product description web page http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp This patch provides a zoom2 base target by copying zoom1 and by making some obvious changes. To configure, run make omap3_zoom2_config Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* 82xx, ids8247: added ids8247 board to MAKEALL scriptHeiko Schocher2009-05-151-0/+1
| | | | Signed-off-by: Heiko Schocher <hs@denx.de>
* at91: add support for the PM9263 board of Ronetix GmbHIlko Iliev2009-04-161-0/+1
| | | | | | | | | | The PM9263 board is based on the AT91SAM9263-EK board. Here is the page on Ronetix website: http://www.ronetix.at/starter_kit_9263.html Signed-off-by: Ilko Iliev <iliev@ronetix.at> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>