summaryrefslogtreecommitdiffstats
path: root/drivers/usb/host
Commit message (Collapse)AuthorAgeFilesLines
* added boot script files to repositoryH. Nikolaus Schaller2012-03-2622-8914/+0
|
* Fix EHCI usb submit timeout and unify with OHCISimon Glass2011-02-192-7/+10
| | | | | | | | | | | | Changed both to use a common timeout for URB submission, since they were using different values and EHCI's was too short. Also fixed EHCI to actually check if urb submission succeeded, rather than silently continuing into the weeds. Change-Id: I7f71499ffaa05187d8e5618db2419e1606007b82 Signed-off-by: Simon Glass <sjg@chromium.org>
* usb: Remove usb_dev_init() from ehci-ppc4xx.cStefan Roese2010-11-261-1/+0
| | | | | | | | | Calling usb_dev_init() from within the EHCI host driver is wrong. The EHCI host driver should have no dependency/interconnection to the USB device driver. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Remy Bohmer <linux@bohmer.net>
* usb: Clear CMD_RUN while issuing CMD_RESET in ehci_reset()Stefan Roese2010-11-261-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | This patch fixes a problem noticed on lwmon5 (PPC440EPx) using the common EHCI driver, when "usb reset" is issued multiple times. Upon the 2nd (and further) "usb reset" command, the command fails with the following messages: => usb reset (Re)start USB... USB: Register 1111 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 5 USB Device(s) found scanning bus for storage devices... 2 Storage Device(s) found => usb reset (Re)start USB... USB: EHCI fail to reset Error, couldn't init Lowlevel part This patch fixes this problem. Now "usb reset" can be called multiple times. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Remy Bohmer <linux@bohmer.net>
* usb: Add WATCHDOG_RESET call to polling loopStefan Roese2010-11-261-0/+2
| | | | | | | | This watchdog reset call is needed here, otherwise the lwmon5 board (PPC440EPx based) will reset upon the "usb reset" command. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Remy Bohmer <linux@bohmer.net>
* usb: fix for USB_ST_STALLED status reporting in ehci_submit_async()Anatolij Gustschin2010-11-261-0/+2
| | | | | | | | | | | Checking the status field of the qTD token in the current code do not take into acount cases where endpoint stall (halted) bit is set together with XactErr status bit. As a result clearing stall on an endpoint won't be done if this status bit was also set. Check for halted bit and report USB_ST_STALLED status if the host controller also indicates endpoit stall condition. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* Switch from archive libraries to partial linkingSebastien Carlier2010-11-171-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Before this commit, weak symbols were not overridden by non-weak symbols found in archive libraries when linking with recent versions of binutils. As stated in the System V ABI, "the link editor does not extract archive members to resolve undefined weak symbols". This commit changes all Makefiles to use partial linking (ld -r) instead of creating library archives, which forces all symbols to participate in linking, allowing non-weak symbols to override weak symbols as intended. This approach is also used by Linux, from which the gmake function cmd_link_o_target (defined in config.mk and used in all Makefiles) is inspired. The name of each former library archive is preserved except for extensions which change from ".a" to ".o". This commit updates references accordingly where needed, in particular in some linker scripts. This commit reveals board configurations that exclude some features but include source files that depend these disabled features in the build, resulting in undefined symbols. Known such cases include: - disabling CMD_NET but not CMD_NFS; - enabling CONFIG_OF_LIBFDT but not CONFIG_QE. Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
* ehci-hcd.c: fix hanging under higher loadWolfgang Denk2010-10-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | This patch solves a problem with USB hanging under higher load on a i.MX31 board. It falls into class of typical USB problems and fixes: if you don't understand the real cause, add a delay somewhere. The problem appeared after introduction of ELF relocation, which results in smaller code, which appears to run faster (probably because it fits better in the cache); turning off the instruction cache, adding debug printf()s and increasing the delay have all been found to make the problem go away. Moving the original "udelay(1)" up in the code to it's new place made the problem appear much less frequently. Increasing the delay to 2 microseconds then made the code run reliably in all (hour-long) tests. To be on the safe side, we set it to 5 microseconds here. Signed-off-by: Heiko schocher <hs@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Stefano Babic <sbabic@denx.de>
* USB: fix Queue Element Transfer Descriptor changesWolfgang Denk2010-10-221-1/+1
| | | | | | | | | | | | | | | | Commit 3ed1607 "USB: sync Queue Element Transfer Descriptor against EHCI spec" added an "__attribute__ ((aligned (32)))" to the declaration of struct qTD, as used for example in the Linux kernel as well. However, it turns out that this attribute causes errors in "usb start" (like "ERROR: NOT USB_CONFIG_DESC 7b" and similar). Drop the attribute again. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Dan Lykowski <lykowdk@gmail.com> Cc: Remy Bohmer <linux@bohmer.net> Cc: Stefano Babic <sbabic@denx.de>
* ehci-pci: print hccr, hcor and hc_lenghtFlorian Fainelli2010-10-221-0/+4
| | | | | | | It is useful to know the EHCI-PCI hccr, hcor and hc_lenght to make sure it was successfully registered, and at the correct location. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* USB: sync Queue Element Transfer Descriptor against EHCI specWolfgang Denk2010-10-202-5/+10
| | | | | | | | | | | | | | | | | | | Appendix B "EHCI 64-Bit Data Structures" of the "Enhanced Host Controller Interface Specification for Universal Serial Bus" (Rev. 1.0, March 12, 2002) defines additional fields which were missing in U-Boot's struct qTD; as these are also present in recent versions of struct ehci_qtd in the Linux kernel, we add them here, too. This fixes some nasty memory corruption problems. Reported-by: Dan Lykowski <lykowdk@gmail.com> See http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/76942 Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Dan Lykowski <lykowdk@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Tested-by: Stefano Babic <sbabic@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-imxWolfgang Denk2010-10-191-0/+2
|\ | | | | | | | | | | | | | | Conflicts: board/logicpd/imx31_litekit/config.mk boards.cfg Signed-off-by: Wolfgang Denk <wd@denx.de>
| * MX31: add delay between USB port setup and resetStefano Babic2010-10-181-0/+2
| | | | | | | | | | | | | | | | Sometimes a usb tree is not popolated after a system reset. It seems a delay is required after setting the USB ports for the MX.31 before resetting the ehci controller. Signed-off-by: Stefano Babic <sbabic@denx.de>
* | MPC5121: Add USB EHCI supportDamien Dusha2010-10-184-1/+169
|/ | | | | | | | | | Signed-off-by: Francesco Rendine <francesco.rendine@valueteam.com> Signed-off-by: Damien Dusha <d.dusha@gmail.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Coding style cleanup; slight file restructuring. Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Remy Bohmer <linux@bohmer.net>
* Merge branch 'master' of git://git.denx.de/u-boot-imxWolfgang Denk2010-10-172-0/+131
|\
| * MX31: Add support for MXC EHCI controllerStefano Babic2010-10-132-0/+131
| | | | | | | | | | | | The patch adds the EHCI controller for the i.MX31 Soc. Signed-off-by: Stefano Babic <sbabic@denx.de>
* | USB: Make non-bulk delay longer in OHCIMarek Vasut2010-10-131-1/+1
|/ | | | | | | This fixes TIMEOUT with my Kingston 32GB USB3.0 flashdrive, which I experienced on my PXA270 (USB 1.1) Vpac270 board. Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
* drivers/usb/host/ohci-hcd: rename readl/writel to ohci_readl/ohci_writelBecky Bruce2010-06-302-80/+85
| | | | | | | | | This avoids a build warning that you see if anyone in the header chain has included io.h (which is coming shortly). The previous code redefined readl/writel; this patch renames it to be specific to ohci. The defines are also moved from ohci-hcd.c to ohci.h. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
* USB OHCI support for at91sam9g45 SoCSergey Matyukevich2010-06-301-0/+14
| | | | | | | | | | Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards. Note that according to errata from Atmel, OHCI is not operational on the first revision of at91sam9g45 chip. So this patch enables OHCI support for later revisions. Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
* EHCI: zero out QH transfer overlay in ehci_submit_async()Sergei Shtylyov2010-06-291-2/+1
| | | | | | | | | | | | | | | | | | | | | ehci_submit_async() doesn't really zero out the QH transfer overlay (as the EHCI specification suggests) which leads to the controller seeing the "token" field as the previous call has left it, i.e.: - if a timeout occured on the previous call (Active bit left as 1), controller incorrectly tries to complete a previous transaction on a newly programmed endpoint; - if a halt occured on the previous call (Halted bit set to 1), controller just ignores the newly programmed TD(s) and the function then keeps returning error ad infinitum. This turned out to be caused by the wrong orger of the arguments to the memset() call in ehci_alloc(), so the allocated TDs weren't cleared either. While at it, stop needlessly initializing the alternate next TD pointer in the QH transfer overlay... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Remy Bohmer <linux@bohmer.net>
* mips: Move cpu/mips/* to arch/mips/cpu/*Peter Tyser2010-04-131-1/+1
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* EHCI: add NEC PCI IDSergei Shtylyov2010-04-081-0/+1
| | | | | | | | | Add NEC EHCI controller to the list of the supported devices. Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com> drivers/usb/host/ehci-pci.c | 1 + 1 file changed, 1 insertion(+)
* EHCI: fix port reset reportingSergei Shtylyov2010-04-081-15/+17
| | | | | | | | | Commit b416191a14770c6bcc6fd67be7decf8159b2baee (Fix EHCI port reset.) didn't move the code that checked for successful clearing of the port reset bit from ehci_submit_root(), relying on wait_ms() call instead. The mentioned code also erroneously reported port reset state when the reset was already completed. Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
* EHCI: fix off-by-one error in ehci_submit_root()Sergei Shtylyov2010-04-081-1/+1
| | | | | | | | | | | USB devices on the 2nd port are not detected and I get the following message: The request port(1) is not configured That's with default CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS value of 2. 'req->index' is 1-based, so the comparison in ehci_submit_root() can't be correct. Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
* EHCI: fix root hub device descriptorSergei Shtylyov2010-04-081-2/+2
| | | | | | | | On little endian machines, EHCI root hub's USB revision is reported as 0.2 -- cpu_to_le16() was missed in the initializer for the 'bcdUSB' descriptor field. The same should be done for the 'bcdDevice' field. Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
* at91: use C structs for AT91 OHCI codeMatthias Fuchs2010-04-031-15/+13
| | | | | | | | | | | | This patch is part of migrating the AT91 support towards using C struct for all SOC access. It removes one more CONFIG_AT91_LEGACY warning. at91_pmc.h needs cleanup after migration of the drivers has been done. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
* convert common files to new SoC accessJens Scharsig2010-02-121-0/+5
| | | | | | | | * add's a warning to all files, which need update to new SoC access * convert common files in cpu/../at91 and a lot of drivers to use c stucture SoC access Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* Add ppc440epx USB ehci support.Chris Zhang2010-01-092-0/+49
| | | | | | | Currently ppc440epx uses OHCI for USB full-speed support. This change adds support for EHCI. Signed-off-by: Chris Zhang <chris@seamicro.com>
* Fix EHCI port reset.Chris Zhang2010-01-091-0/+3
| | | | | | | | | In USB ehci driver, the port reset is not terminated. EHCI spec says "A host controller must terminate the reset and stabilize the state of the port within 2 milliseconds". Without termination, a port stays at reset state. This is observed on ppc4xx(sequoia) boards. Signed-off-by: Chris Zhang <chris@seamicro.com>
* USB Consolidate descriptor definitionsTom Rix2009-12-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The header files usb.h and usbdescriptors.h have the same nameed structure definitions for usb_config_descriptor usb_interface_descriptor usb_endpoint_descriptor usb_device_descriptor usb_string_descriptor These are out right duplicates in usb.h usb_device_descriptor usb_string_descriptor This one has extra unused elements usb_endpoint_descriptor unsigned char bRefresh unsigned char bSynchAddress; These in usb.h have extra elements at the end of the usb 2.0 specified descriptor and are used. usb_config_descriptor usb_interface_descriptor The change is to consolidate the definition of the descriptors to usbdescriptors.h. The dublicates in usb.h are removed. The extra element structure will have their name shorted by removing the '_descriptor' suffix. So usb_config_descriptor -> usb_config usb_interface_descriptor -> usb_interface For these, the common descriptor elements are accessed now by an element 'desc'. As an example - if (iface->bInterfaceClass != USB_CLASS_HUB) + if (iface->desc.bInterfaceClass != USB_CLASS_HUB) This has been compile tested on MAKEALL arm, ppc and mips. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* Add a unified s3c24x0 header filekevin.morfitt@fearnside-systems.co.uk2009-11-271-2/+1
| | | | | | | | | | This patch adds a unified s3c24x0 cpu header file that selects the header file for the specific s3c24x0 cpu from the SOC and CPU configs defined in board config file. This removes the current chain of s3c24-type #ifdef's from the s3c24x0 code. Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* s3c64xx: move s3c64xx header files to asm-arm/arch-s3c64xxMinkyu Kang2009-11-271-1/+1
| | | | | | | This patch moves the s3c64xx header files from include/ to include/asm-arm/arch-s3c64xx Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* usb: bugfix driver/usb/host/ehci-hcd.c function ehci_submit_rootPrafulla Wadaskar2009-07-231-2/+2
| | | | | | | | | | | | This change is cheked in Linux source and fix found to be in sync. This patch is tested for USB host interface on Kirkwood based Sheevaplug platform (ARM little endian board) Risk: the impact of this patch is not validated on big endian board. This need to be checked... Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* Coding Style cleanup; update CHANGELOG.Wolfgang Denk2009-07-231-1/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* usb: Fix compiler warning with gcc4.4Kumar Gala2009-07-111-2/+2
| | | | | | | | | ehci-hcd.c: In function 'ehci_submit_root': ehci-hcd.c:719: warning: value computed is not used ehci-hcd.c:748: warning: value computed is not used Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* usb: add Marvell Kirkwood ehci host controller driverPrafulla Wadaskar2009-07-092-0/+109
| | | | | | | This driver is tested on Sheevaplug platform Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc8xxx: USB: fix: access of ehci struct elementsVivek Mahajan2009-07-091-9/+9
| | | | | | | | | This patch fixes the access to the 'ehci' struct elements which should have been taken care off in 4ef01010aa4799c759d75e67007fdd3a38c88c8a Sorry about that. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc83xx: USB: Reorganized its supportVivek Mahajan2009-06-121-35/+18
| | | | | | | | | | | | | | | | | The following patch reorganizes/reworks the USB support for mpc83xx as under:- * Moves the 83xx USB clock init from drivers/usb/host/ehci-fsl.c to cpu/mpx83xx/cpu_init.c * Board specific usb_phy_type is read from the environment * Adds USB EHCI specific structure in include/usb/ehci-fsl.h * Copyrights revamped in most of the following files Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc8xxx: USB: Relocates ehci-fsl.h to include/usbVivek Mahajan2009-06-122-87/+1
| | | | | | | | The following patch moves 8xxx-specifc USB #defines from drivers/usb/host/ehci-fsl.h to include/usb. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc8xxx: USB: Removed reenablement of its interfaceVivek Mahajan2009-06-121-4/+0
| | | | | | | | | | To prepare for the 85xx USB support, which requires interface enablement only once in (specified) order, no different than instructions for enabling the interface under 83xx. It is unknown why the original author enabled the interface twice (checked for references in errata, etc). Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* at91: fix a USB problem for AT91SAM9261RONETIX - Ilko Iliev2009-06-091-1/+2
| | | | | | | | | | | | This patch corrects the missing PLLB initialization in usb_cpu_init() for AT91SAM9261. Because of the missing PLLB initialization, the USB support for all AT91SAM9261 based boards will work only if the PLLB is configured by a precedent bootloader. Signed-off-by: Ilko Iliev <iliev@ronetix.at> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* Fix e-mail address of Gary Jennejohn.Detlev Zundel2009-05-152-2/+2
| | | | Signed-off-by: Detlev Zundel <dzu@denx.de>
* Replace __attribute references with __attribute__Peter Tyser2009-04-281-4/+4
| | | | | | | | __attribute__ follows gcc's documented syntax and is generally more common than __attribute. This change is only asthetic and should not affect functionality. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* at91sam9/at91cap: improve clock frameworkJean-Christophe PLAGNIOL-VILLARD2009-04-161-1/+2
| | | | | | calculate dynamically the clock rate and pllb setting for usb Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* drivers/usb: regorganisationJean-Christophe PLAGNIOL-VILLARD2009-04-0619-0/+8520
move to linux usb driver organisation as following drivers/usb/gadget drivers/usb/host drivers/usb/musb Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
generated by cgit v1.1 at 2024-09-18 13:17:45 +0000