From c562f9b26c9f5abfe5b89c1fbe816e24a705334f Mon Sep 17 00:00:00 2001 From: "H. Nikolaus Schaller" Date: Tue, 20 Nov 2012 13:01:02 +0100 Subject: choose correct I2C bus --- u-boot/board/goldelico/gta04/commands.c | 1 + u-boot/board/goldelico/gta04/systest.c | 9 +++++---- 2 files changed, 6 insertions(+), 4 deletions(-) diff --git a/u-boot/board/goldelico/gta04/commands.c b/u-boot/board/goldelico/gta04/commands.c index 45520d2..b65e463 100644 --- a/u-boot/board/goldelico/gta04/commands.c +++ b/u-boot/board/goldelico/gta04/commands.c @@ -595,6 +595,7 @@ static int do_systest(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) return wlanbttest(0); // just power on } if (strncmp ("ch", argv[1], 2) == 0) { + i2c_set_bus_num(TWL4030_I2C_BUS); // I2C1 return twl4030_init_battery_charging(); } if (strncmp ("gp", argv[1], 2) == 0) { diff --git a/u-boot/board/goldelico/gta04/systest.c b/u-boot/board/goldelico/gta04/systest.c index 473e9e4..18fde65 100644 --- a/u-boot/board/goldelico/gta04/systest.c +++ b/u-boot/board/goldelico/gta04/systest.c @@ -549,7 +549,7 @@ int irdatest(void) } #ifdef CONFIG_OMAP3_GTA04 -int wlabbtpower(void) +int wlanbtpower(void) { /* Bluetooth VAUX4 = 3.3V -- CHECKME: 3.3 V is not officially supported by TPS! We use 0x09 = 2.8V here*/ #define TCA6507_BUS (2-1) // I2C2 #define TCA6507_ADDRESS 0x45 @@ -564,7 +564,7 @@ int wlabbtpower(void) i2c_reg_write(TCA6507_ADDRESS, TCA6507_SELECT0, 0); i2c_reg_write(TCA6507_ADDRESS, TCA6507_SELECT1, 0); i2c_reg_write(TCA6507_ADDRESS, TCA6507_SELECT2, 0x40); // pull down reset for WLAN&BT chip - i2c_set_bus_num(0); // write I2C1 + i2c_set_bus_num(TWL4030_I2C_BUS); // write I2C1 printf("power on VAUX4\n"); twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX4_DEDICATED, /* 2.8V: */ 0x09 /* 3.15V: 0x0c */, @@ -576,7 +576,7 @@ int wlabbtpower(void) i2c_reg_write(TCA6507_ADDRESS, TCA6507_SELECT0, 0); i2c_reg_write(TCA6507_ADDRESS, TCA6507_SELECT1, 0); i2c_reg_write(TCA6507_ADDRESS, TCA6507_SELECT2, 0); // release reset for WLAN&BT chip - i2c_set_bus_num(0); // write I2C1 + i2c_set_bus_num(TWL4030_I2C_BUS); // write I2C1 return 0; } #endif @@ -584,7 +584,7 @@ int wlabbtpower(void) int wlanbttest(int test) { /* Bluetooth VAUX4 = 3.3V -- CHECKME: 3.3 V is not officially supported! We use 0x09 = 2.8V here*/ #ifdef CONFIG_OMAP3_GTA04 - wlabbtpower(); + wlanbtpower(); if(test) { // now, we should be able to test the UART for the BT part... @@ -599,6 +599,7 @@ int wlanbttest(int test) int OTGchargepump(int enable) { + i2c_set_bus_num(TWL4030_I2C_BUS); // I2C1 if(enable) twl4030_i2c_write_u8(TWL4030_CHIP_USB, 0x20, TWL4030_USB_OTG_CTRL_SET); else -- cgit v1.1