From 3f0606ad0b5639f7f22848fe5b4574e754d0470f Mon Sep 17 00:00:00 2001 From: "Aubrey.Li" Date: Fri, 9 Mar 2007 13:38:44 +0800 Subject: [Blackfin]PATCH-1/2]: Remove obsolete blackfin port and add bf533 platform support --- include/configs/bf533-stamp.h | 475 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 475 insertions(+) create mode 100644 include/configs/bf533-stamp.h (limited to 'include/configs/bf533-stamp.h') diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h new file mode 100644 index 0000000..353a43c --- /dev/null +++ b/include/configs/bf533-stamp.h @@ -0,0 +1,475 @@ +/* + * U-boot - Configuration file for BF533 STAMP board + */ + +#ifndef __CONFIG_STAMP_H__ +#define __CONFIG_STAMP_H__ + +#define CONFIG_STAMP 1 +#define CONFIG_RTC_BFIN 1 +#define CONFIG_BF533 1 +/* + * Boot Mode Set + * Blackfin can support several boot modes + */ +#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */ +#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */ +#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */ +/* Define the boot mode */ +#define BFIN_BOOT_MODE BF533_BYPASS_BOOT +//#define BFIN_BOOT_MODE BF533_SPI_BOOT + +#define CONFIG_PANIC_HANG 1 + +#define ADSP_BF531 0x31 +#define ADSP_BF532 0x32 +#define ADSP_BF533 0x33 +#define BFIN_CPU ADSP_BF533 + +/* This sets the default state of the cache on U-Boot's boot */ +#define CONFIG_ICACHE_ON +#define CONFIG_DCACHE_ON + +/* Define where the uboot will be loaded by on-chip boot rom */ +#define APP_ENTRY 0x00001000 + +/* + * Stringize definitions - needed for environmental settings + */ +#define STRINGIZE2(x) #x +#define STRINGIZE(x) STRINGIZE2(x) + +/* + * Board settings + * + */ +#define CONFIG_DRIVER_SMC91111 1 +#define CONFIG_SMC91111_BASE 0x20300300 + +/* FLASH/ETHERNET uses the same address range */ +#define SHARED_RESOURCES 1 + +/* Is I2C bit-banged? */ +#define CONFIG_SOFT_I2C 1 + +/* + * Software (bit-bang) I2C driver configuration + */ +#define PF_SCL PF3 +#define PF_SDA PF2 + +/* + * Video splash screen support + */ +#define CONFIG_VIDEO 0 + +#define CONFIG_VDSP 1 + +/* + * Clock settings + * + */ + +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 11059200 +/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ +/* 1=CLKIN/2 */ +#define CONFIG_CLKIN_HALF 0 +/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ +/* 1=bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */ +/* Values can range from 1-64 */ +#define CONFIG_VCO_MULT 36 +/* CONFIG_CCLK_DIV controls what the core clock divider is */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 5 +/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ +/* Values can range from 2-65535 */ +/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ +#define CONFIG_SPI_BAUD 2 + +#if (BFIN_BOOT_MODE == BF533_SPI_BOOT) +#define CONFIG_SPI_BAUD_INITBLOCK 4 +#endif + + +/* + * Network settings + * + */ + +#if (CONFIG_DRIVER_SMC91111) +#if 0 +#define CONFIG_MII +#endif + +/* network support */ +#define CONFIG_IPADDR 192.168.0.15 +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_GATEWAYIP 192.168.0.1 +#define CONFIG_SERVERIP 192.168.0.2 +#define CONFIG_HOSTNAME STAMP +#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs + +/* To remove hardcoding and enable MAC storage in EEPROM */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */ +#endif /* CONFIG_DRIVER_SMC91111 */ + +/* + * Flash settings + * + */ + +#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ +#define CFG_FLASH_CFI_AMD_RESET + +#define CFG_FLASH_BASE 0x20000000 +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ + +#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT) +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR 0x20004000 +#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE) +#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT) +#define CFG_ENV_IS_IN_EEPROM 1 +#define CFG_ENV_OFFSET 0x4000 +#define CFG_ENV_HEADER (CFG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */ +#endif + +#define CFG_ENV_SIZE 0x2000 +#define CFG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */ +#define ENV_IS_EMBEDDED + +#define CFG_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */ +#define CFG_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */ + +/* JFFS Partition offset set */ +#define CFG_JFFS2_FIRST_BANK 0 +#define CFG_JFFS2_NUM_BANKS 1 +/* 512k reserved for u-boot */ +#define CFG_JFFS2_FIRST_SECTOR 11 + +/* + * following timeouts shall be used once the + * Flash real protection is enabled + */ +#define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */ +#define CFG_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */ + +/* + * SDRAM settings & memory map + * + */ + +#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */ +#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */ +#define CONFIG_MEM_MT48LC64M4A2FB_7E 1 + +#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT) +#define CFG_MEMTEST_START 0x00000000 /* memtest works on */ +#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT) +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#endif + +#define CFG_SDRAM_BASE 0x00000000 + +#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 *1024) +#define CFG_MEMTEST_END (CFG_MAX_RAM_SIZE - 0x80000 - 1) +#define CONFIG_LOADADDR 0x01000000 + +#define CFG_LOAD_ADDR CONFIG_LOADADDR +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CFG_GBL_DATA_SIZE 0x4000 /* Reserve 16k for Global Data */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ + +#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - 0x40000) +#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN) +#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE) +#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4) + +/* Check to make sure everything fits in SDRAM */ +#if ((CFG_MONITOR_BASE + CFG_MONITOR_LEN) > CFG_MAX_RAM_SIZE) + #error Memory Map does not fit into configuration +#endif + +#if ( CONFIG_CLKIN_HALF == 0 ) +#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) +#else +#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) +#endif + +#if (CONFIG_PLL_BYPASS == 0) +#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) +#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) +#else +#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ +#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ +#endif + +#if (BFIN_BOOT_MODE == BF533_SPI_BOOT) +#if (CONFIG_SCLK_HZ / (2*CONFIG_SPI_BAUD) > 20000000) +#define CONFIG_SPI_FLASH_FAST_READ 1 /* Needed if SPI_CLK > 20 MHz */ +#else +#undef CONFIG_SPI_FLASH_FAST_READ +#endif +#endif +/* + * Command settings + * + */ + +#define CFG_LONGHELP 1 +#define CONFIG_CMDLINE_EDITING 1 + +#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT) +#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */ +#endif + /* configuration lookup from the BOOTP/DHCP server, */ + /* but not try to load any image using TFTP */ + +#define CONFIG_BOOTDELAY 5 +#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */ +#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT) +#define CONFIG_BOOTCOMMAND "run ramboot" +#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT) +#define CONFIG_BOOTCOMMAND "eeprom read 0x1000000 0x100000 0x180000;icache on;dcache on;bootm 0x1000000" +#endif + +#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600" + +#if (CONFIG_DRIVER_SMC91111) +#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \ + CFG_CMD_PING | \ + CFG_CMD_ELF | \ + CFG_CMD_CACHE | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_EEPROM | \ + CFG_CMD_DATE) + +#else +#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \ + CFG_CMD_ELF | \ + CFG_CMD_CACHE | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_EEPROM | \ + CFG_CMD_DATE) + +#endif + +#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT) +#if (CONFIG_DRIVER_SMC91111) +#define CONFIG_EXTRA_ENV_SETTINGS \ + "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \ + "$(rootpath) console=ttyBF0,57600\0" \ + "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ + "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \ + "ramboot=tftpboot $(loadaddr) linux; " \ + "run ramargs;run addip;bootelf\0" \ + "nfsboot=tftpboot $(loadaddr) linux; " \ + "run nfsargs;run addip;bootelf\0" \ + "flashboot=bootm 0x20100000\0" \ + "update=tftpboot $(loadaddr) u-boot.bin; " \ + "protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \ + "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \ + "" +#else +#define CONFIG_EXTRA_ENV_SETTINGS \ + "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ + "flashboot=bootm 0x20100000\0" \ + "" +#endif + +#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT) +#define CONFIG_EXTRA_ENV_SETTINGS \ + "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \ + "$(rootpath) console=ttyBF0,57600\0" \ + "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ + "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \ + "ramboot=tftpboot $(loadaddr) linux; " \ + "run ramargs;run addip;bootelf\0" \ + "nfsboot=tftpboot $(loadaddr) linux; " \ + "run nfsargs;run addip;bootelf\0" \ + "flashboot=bootm 0x20100000\0" \ + "update=tftpboot $(loadaddr) u-boot.ldr;" \ + "eeprom write $(loadaddr) 0x0 $(filesize);\0"\ + "" +#endif + +#ifdef CONFIG_SOFT_I2C +#if (!CONFIG_SOFT_I2C) +#undef CONFIG_SOFT_I2C +#endif +#endif + +#if (CONFIG_SOFT_I2C) +#define CONFIG_COMMANDS2 CFG_CMD_I2C +#else +#define CONFIG_COMMANDS2 0 +#endif /* CONFIG_SOFT_I2C */ + +#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT) +#define CONFIG_COMMANDS ( CONFIG_COMMANDS1 | CONFIG_COMMANDS2 | CFG_CMD_DHCP) +#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT) +#define CONFIG_COMMANDS ( CONFIG_COMMANDS1 | CONFIG_COMMANDS2) +#endif + +/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Console settings + * + */ + +#define CONFIG_BAUDRATE 57600 +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#if (BFIN_BOOT_MODE == BF533_SPI_BOOT) +#if (BFIN_CPU == ADSP_BF531) +#define CFG_PROMPT "serial_bf531> " /* Monitor Command Prompt */ +#elif (BFIN_CPU == ADSP_BF532) +#define CFG_PROMPT "serial_bf532> " /* Monitor Command Prompt */ +#else +#define CFG_PROMPT "serial_bf533> " /* Monitor Command Prompt */ +#endif +#else +#if (BFIN_CPU == ADSP_BF531) +#define CFG_PROMPT "bf531> " /* Monitor Command Prompt */ +#elif (BFIN_CPU == ADSP_BF532) +#define CFG_PROMPT "bf532> " /* Monitor Command Prompt */ +#else +#define CFG_PROMPT "bf533> " /* Monitor Command Prompt */ +#endif +#endif + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_LOADS_ECHO 1 + +/* + * I2C settings + * By default PF2 is used as SDA and PF3 as SCL on the Stamp board + */ +#if (CONFIG_SOFT_I2C) + +#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;") +#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;") +#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;") +#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;") +#define I2C_SDA(bit) if(bit) { \ + *pFIO_FLAG_S = PF_SDA; \ + asm("ssync;"); \ + } \ + else { \ + *pFIO_FLAG_C = PF_SDA; \ + asm("ssync;"); \ + } +#define I2C_SCL(bit) if(bit) { \ + *pFIO_FLAG_S = PF_SCL; \ + asm("ssync;"); \ + } \ + else { \ + *pFIO_FLAG_C = PF_SCL; \ + asm("ssync;"); \ + } +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#define CFG_I2C_SPEED 50000 +#define CFG_I2C_SLAVE 0xFE +#endif /* CONFIG_SOFT_I2C */ + +/* + * Compact Flash settings + */ + +/* Enabled below option for CF support */ +/* #define CONFIG_STAMP_CF 1 */ + +#if defined(CONFIG_STAMP_CF) && (CONFIG_COMMANDS & CFG_CMD_IDE) + +#define CONFIG_MISC_INIT_R 1 +#define CONFIG_DOS_PARTITION 1 +/* + * IDE/ATA stuff + */ +#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ +#undef CONFIG_IDE_LED /* no led for ide supported */ +#undef CONFIG_IDE_RESET /* no reset for ide supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */ +#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ + +#define CFG_ATA_BASE_ADDR 0x20200000 +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */ +#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */ +#define CFG_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */ + +#define CFG_ATA_STRIDE 2 +#endif + +/* + * Miscellaneous configurable options + */ + +#define CFG_HZ 1000 /* 1ms time tick */ + +#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */ + +#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */ + +#define CONFIG_SPI + +#ifdef CONFIG_VIDEO +#if (CONFIG_VIDEO) +#define CONFIG_SPLASH_SCREEN 1 +#define CONFIG_SILENT_CONSOLE 1 +#else +#undef CONFIG_VIDEO +#endif +#endif + +/* + * FLASH organization and environment definitions + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* 0xFF, 0xBBC3BBc3, 0x99B39983 */ +/*#define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN) +#define AMBCTL0VAL (B1WAT_11 | B1RAT_11 | B1HT_3 | B1ST_4 | B1TT_4 | B1RDYPOL | \ + B1RDYEN | B0WAT_11 | B0RAT_11 | B0HT_3 | B0ST_4 | B0TT_4 | B0RDYPOL | B0RDYEN) +#define AMBCTL1VAL (B3WAT_9 | B3RAT_9 | B3HT_2 | B3ST_3 | B3TT_4 | B3RDYPOL | \ + B3RDYEN | B2WAT_9 | B2RAT_9 | B2HT_2 | B2ST_4 | B2TT_4 | B2RDYPOL | B2RDYEN) +*/ +#define AMGCTLVAL 0xFF +#define AMBCTL0VAL 0xBBC3BBC3 +#define AMBCTL1VAL 0x99B39983 +#define CF_AMBCTL1VAL 0x99B3ffc2 + +#ifdef CONFIG_VDSP +#define ET_EXEC_VDSP 0x8 +#define SHT_STRTAB_VDSP 0x1 +#define ELFSHDRSIZE_VDSP 0x2C +#define VDSP_ENTRY_ADDR 0xFFA00000 +#endif + + +#endif -- cgit v1.1