diff options
Diffstat (limited to 'Documentation/devicetree')
43 files changed, 1241 insertions, 14 deletions
diff --git a/Documentation/devicetree/bindings/arm/atmel-aic.txt b/Documentation/devicetree/bindings/arm/atmel-aic.txt new file mode 100644 index 0000000..aabca4f --- /dev/null +++ b/Documentation/devicetree/bindings/arm/atmel-aic.txt @@ -0,0 +1,38 @@ +* Advanced Interrupt Controller (AIC) + +Required properties: +- compatible: Should be "atmel,<chip>-aic" +- interrupt-controller: Identifies the node as an interrupt controller. +- interrupt-parent: For single AIC system, it is an empty property. +- #interrupt-cells: The number of cells to define the interrupts. It sould be 2. + The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet). + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + Valid combinations are 1, 2, 3, 4, 8. + Default flag for internal sources should be set to 4 (active high). +- reg: Should contain AIC registers location and length + +Examples: + /* + * AIC + */ + aic: interrupt-controller@fffff000 { + compatible = "atmel,at91rm9200-aic"; + interrupt-controller; + interrupt-parent; + #interrupt-cells = <2>; + reg = <0xfffff000 0x200>; + }; + + /* + * An interrupt generating device that is wired to an AIC. + */ + dma: dma-controller@ffffec00 { + compatible = "atmel,at91sam9g45-dma"; + reg = <0xffffec00 0x200>; + interrupts = <21 4>; + }; diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt new file mode 100644 index 0000000..ecc81e3 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -0,0 +1,92 @@ +Atmel AT91 device tree bindings. +================================ + +PIT Timer required properties: +- compatible: Should be "atmel,at91sam9260-pit" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt for the PIT which is the IRQ line + shared across all System Controller members. + +TC/TCLIB Timer required properties: +- compatible: Should be "atmel,<chip>-pit". + <chip> can be "at91rm9200" or "at91sam9x5" +- reg: Should contain registers location and length +- interrupts: Should contain all interrupts for the TC block + Note that you can specify several interrupt cells if the TC + block has one interrupt per channel. + +Examples: + +One interrupt per TC block: + tcb0: timer@fff7c000 { + compatible = "atmel,at91rm9200-tcb"; + reg = <0xfff7c000 0x100>; + interrupts = <18 4>; + }; + +One interrupt per TC channel in a TC block: + tcb1: timer@fffdc000 { + compatible = "atmel,at91rm9200-tcb"; + reg = <0xfffdc000 0x100>; + interrupts = <26 4 27 4 28 4>; + }; + +RSTC Reset Controller required properties: +- compatible: Should be "atmel,<chip>-rstc". + <chip> can be "at91sam9260" or "at91sam9g45" +- reg: Should contain registers location and length + +Example: + + rstc@fffffd00 { + compatible = "atmel,at91sam9260-rstc"; + reg = <0xfffffd00 0x10>; + }; + +RAMC SDRAM/DDR Controller required properties: +- compatible: Should be "atmel,at91sam9260-sdramc", + "atmel,at91sam9g45-ddramc", +- reg: Should contain registers location and length + For at91sam9263 and at91sam9g45 you must specify 2 entries. + +Examples: + + ramc0: ramc@ffffe800 { + compatible = "atmel,at91sam9g45-ddramc"; + reg = <0xffffe800 0x200>; + }; + + ramc0: ramc@ffffe400 { + compatible = "atmel,at91sam9g45-ddramc"; + reg = <0xffffe400 0x200 + 0xffffe600 0x200>; + }; + +SHDWC Shutdown Controller + +required properties: +- compatible: Should be "atmel,<chip>-shdwc". + <chip> can be "at91sam9260", "at91sam9rl" or "at91sam9x5". +- reg: Should contain registers location and length + +optional properties: +- atmel,wakeup-mode: String, operation mode of the wakeup mode. + Supported values are: "none", "high", "low", "any". +- atmel,wakeup-counter: Counter on Wake-up 0 (between 0x0 and 0xf). + +optional at91sam9260 properties: +- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up. + +optional at91sam9rl properties: +- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up. +- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up. + +optional at91sam9x5 properties: +- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up. + +Example: + + rstc@fffffd00 { + compatible = "atmel,at91sam9260-rstc"; + reg = <0xfffffd00 0x10>; + }; diff --git a/Documentation/devicetree/bindings/arm/atmel-pmc.txt b/Documentation/devicetree/bindings/arm/atmel-pmc.txt new file mode 100644 index 0000000..389bed5 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/atmel-pmc.txt @@ -0,0 +1,11 @@ +* Power Management Controller (PMC) + +Required properties: +- compatible: Should be "atmel,at91rm9200-pmc" +- reg: Should contain PMC registers location and length + +Examples: + pmc: pmc@fffffc00 { + compatible = "atmel,at91rm9200-pmc"; + reg = <0xfffffc00 0x100>; + }; diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt new file mode 100644 index 0000000..6528e21 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -0,0 +1,21 @@ +* Samsung Exynos Power Domains + +Exynos processors include support for multiple power domains which are used +to gate power to one or more peripherals on the processor. + +Required Properties: +- compatiable: should be one of the following. + * samsung,exynos4210-pd - for exynos4210 type power domain. +- reg: physical base address of the controller and length of memory mapped + region. + +Optional Properties: +- samsung,exynos4210-pd-off: Specifies that the power domain is in turned-off + state during boot and remains to be turned-off until explicitly turned-on. + +Example: + + lcd0: power-domain-lcd0 { + compatible = "samsung,exynos4210-pd"; + reg = <0x10023C00 0x10>; + }; diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index 54bddda..bfbc771 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -28,3 +28,25 @@ Required root node properties: i.MX6 Quad SABRE Lite Board Required root node properties: - compatible = "fsl,imx6q-sabrelite", "fsl,imx6q"; + +Generic i.MX boards +------------------- + +No iomux setup is done for these boards, so this must have been configured +by the bootloader for boards to work with the generic bindings. + +i.MX27 generic board +Required root node properties: + - compatible = "fsl,imx27"; + +i.MX51 generic board +Required root node properties: + - compatible = "fsl,imx51"; + +i.MX53 generic board +Required root node properties: + - compatible = "fsl,imx53"; + +i.MX6q generic board +Required root node properties: + - compatible = "fsl,imx6q"; diff --git a/Documentation/devicetree/bindings/arm/mrvl.txt b/Documentation/devicetree/bindings/arm/mrvl.txt new file mode 100644 index 0000000..d8de933 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mrvl.txt @@ -0,0 +1,6 @@ +Marvell Platforms Device Tree Bindings +---------------------------------------------------- + +PXA168 Aspenite Board +Required root node properties: + - compatible = "mrvl,pxa168-aspenite", "mrvl,pxa168"; diff --git a/Documentation/devicetree/bindings/arm/omap/intc.txt b/Documentation/devicetree/bindings/arm/omap/intc.txt new file mode 100644 index 0000000..f2583e6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/intc.txt @@ -0,0 +1,27 @@ +* OMAP Interrupt Controller + +OMAP2/3 are using a TI interrupt controller that can support several +configurable number of interrupts. + +Main node required properties: + +- compatible : should be: + "ti,omap2-intc" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The type shall be a <u32> and the value shall be 1. + + The cell contains the interrupt number in the range [0-128]. +- ti,intc-size: Number of interrupts handled by the interrupt controller. +- reg: physical base address and size of the intc registers map. + +Example: + + intc: interrupt-controller@1 { + compatible = "ti,omap2-intc"; + interrupt-controller; + #interrupt-cells = <1>; + ti,intc-size = <96>; + reg = <0x48200000 0x1000>; + }; + diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index dbdab40..e78e8bc 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -5,7 +5,7 @@ IPs present in the SoC. On top of that an omap_device is created to extend the platform_device capabilities and to allow binding with one or several hwmods. The hwmods will contain all the information to build the device: -adresse range, irq lines, dma lines, interconnect, PRCM register, +address range, irq lines, dma lines, interconnect, PRCM register, clock domain, input clocks. For the moment just point to the existing hwmod, the next step will be to move data from hwmod to device-tree representation. @@ -41,3 +41,9 @@ Boards: - OMAP4 PandaBoard : Low cost community board compatible = "ti,omap4-panda", "ti,omap4430" + +- OMAP3 EVM : Software Developement Board for OMAP35x, AM/DM37x + compatible = "ti,omap3-evm", "ti,omap3" + +- AM335X EVM : Software Developement Board for AM335x + compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3" diff --git a/Documentation/devicetree/bindings/arm/sirf.txt b/Documentation/devicetree/bindings/arm/sirf.txt index 6b07f65..1881e1c 100644 --- a/Documentation/devicetree/bindings/arm/sirf.txt +++ b/Documentation/devicetree/bindings/arm/sirf.txt @@ -1,3 +1,3 @@ -prima2 "cb" evalutation board +prima2 "cb" evaluation board Required root node properties: - compatible = "sirf,prima2-cb", "sirf,prima2"; diff --git a/Documentation/devicetree/bindings/arm/spear.txt b/Documentation/devicetree/bindings/arm/spear.txt new file mode 100644 index 0000000..f8e54f0 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/spear.txt @@ -0,0 +1,8 @@ +ST SPEAr Platforms Device Tree Bindings +--------------------------------------- + +Boards with the ST SPEAr600 SoC shall have the following properties: + +Required root node property: + +compatible = "st,spear600"; diff --git a/Documentation/devicetree/bindings/arm/tegra/emc.txt b/Documentation/devicetree/bindings/arm/tegra/emc.txt new file mode 100644 index 0000000..09335f8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra/emc.txt @@ -0,0 +1,100 @@ +Embedded Memory Controller + +Properties: +- name : Should be emc +- #address-cells : Should be 1 +- #size-cells : Should be 0 +- compatible : Should contain "nvidia,tegra20-emc". +- reg : Offset and length of the register set for the device +- nvidia,use-ram-code : If present, the sub-nodes will be addressed + and chosen using the ramcode board selector. If omitted, only one + set of tables can be present and said tables will be used + irrespective of ram-code configuration. + +Child device nodes describe the memory settings for different configurations and clock rates. + +Example: + + emc@7000f400 { + #address-cells = < 1 >; + #size-cells = < 0 >; + compatible = "nvidia,tegra20-emc"; + reg = <0x7000f4000 0x200>; + } + + +Embedded Memory Controller ram-code table + +If the emc node has the nvidia,use-ram-code property present, then the +next level of nodes below the emc table are used to specify which settings +apply for which ram-code settings. + +If the emc node lacks the nvidia,use-ram-code property, this level is omitted +and the tables are stored directly under the emc node (see below). + +Properties: + +- name : Should be emc-tables +- nvidia,ram-code : the binary representation of the ram-code board strappings + for which this node (and children) are valid. + + + +Embedded Memory Controller configuration table + +This is a table containing the EMC register settings for the various +operating speeds of the memory controller. They are always located as +subnodes of the emc controller node. + +There are two ways of specifying which tables to use: + +* The simplest is if there is just one set of tables in the device tree, + and they will always be used (based on which frequency is used). + This is the preferred method, especially when firmware can fill in + this information based on the specific system information and just + pass it on to the kernel. + +* The slightly more complex one is when more than one memory configuration + might exist on the system. The Tegra20 platform handles this during + early boot by selecting one out of possible 4 memory settings based + on a 2-pin "ram code" bootstrap setting on the board. The values of + these strappings can be read through a register in the SoC, and thus + used to select which tables to use. + +Properties: +- name : Should be emc-table +- compatible : Should contain "nvidia,tegra20-emc-table". +- reg : either an opaque enumerator to tell different tables apart, or + the valid frequency for which the table should be used (in kHz). +- clock-frequency : the clock frequency for the EMC at which this + table should be used (in kHz). +- nvidia,emc-registers : a 46 word array of EMC registers to be programmed + for operation at the 'clock-frequency' setting. + The order and contents of the registers are: + RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT, + WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR, + PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW, + TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE, + ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE, + ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0, + CFG_CLKTRIM_1, CFG_CLKTRIM_2 + + emc-table@166000 { + reg = <166000>; + compatible = "nvidia,tegra20-emc-table"; + clock-frequency = < 166000 >; + nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 >; + }; + + emc-table@333000 { + reg = <333000>; + compatible = "nvidia,tegra20-emc-table"; + clock-frequency = < 333000 >; + nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 >; + }; diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt new file mode 100644 index 0000000..b5846e2 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt @@ -0,0 +1,19 @@ +NVIDIA Tegra Power Management Controller (PMC) + +Properties: +- name : Should be pmc +- compatible : Should contain "nvidia,tegra<chip>-pmc". +- reg : Offset and length of the register set for the device +- nvidia,invert-interrupt : If present, inverts the PMU interrupt signal. + The PMU is an external Power Management Unit, whose interrupt output + signal is fed into the PMC. This signal is optionally inverted, and then + fed into the ARM GIC. The PMC is not involved in the detection or + handling of this interrupt signal, merely its inversion. + +Example: + +pmc@7000f400 { + compatible = "nvidia,tegra20-pmc"; + reg = <0x7000e400 0x400>; + nvidia,invert-interrupt; +}; diff --git a/Documentation/devicetree/bindings/arm/twd.txt b/Documentation/devicetree/bindings/arm/twd.txt new file mode 100644 index 0000000..75b8610 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/twd.txt @@ -0,0 +1,48 @@ +* ARM Timer Watchdog + +ARM 11MP, Cortex-A5 and Cortex-A9 are often associated with a per-core +Timer-Watchdog (aka TWD), which provides both a per-cpu local timer +and watchdog. + +The TWD is usually attached to a GIC to deliver its two per-processor +interrupts. + +** Timer node required properties: + +- compatible : Should be one of: + "arm,cortex-a9-twd-timer" + "arm,cortex-a5-twd-timer" + "arm,arm11mp-twd-timer" + +- interrupts : One interrupt to each core + +- reg : Specify the base address and the size of the TWD timer + register window. + +Example: + + twd-timer@2c000600 { + compatible = "arm,arm11mp-twd-timer""; + reg = <0x2c000600 0x20>; + interrupts = <1 13 0xf01>; + }; + +** Watchdog node properties: + +- compatible : Should be one of: + "arm,cortex-a9-twd-wdt" + "arm,cortex-a5-twd-wdt" + "arm,arm11mp-twd-wdt" + +- interrupts : One interrupt to each core + +- reg : Specify the base address and the size of the TWD watchdog + register window. + +Example: + + twd-watchdog@2c000620 { + compatible = "arm,arm11mp-twd-wdt"; + reg = <0x2c000620 0x20>; + interrupts = <1 14 0xf01>; + }; diff --git a/Documentation/devicetree/bindings/arm/vexpress.txt b/Documentation/devicetree/bindings/arm/vexpress.txt new file mode 100644 index 0000000..ec8b50c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vexpress.txt @@ -0,0 +1,146 @@ +ARM Versatile Express boards family +----------------------------------- + +ARM's Versatile Express platform consists of a motherboard and one +or more daughterboards (tiles). The motherboard provides a set of +peripherals. Processor and RAM "live" on the tiles. + +The motherboard and each core tile should be described by a separate +Device Tree source file, with the tile's description including +the motherboard file using a /include/ directive. As the motherboard +can be initialized in one of two different configurations ("memory +maps"), care must be taken to include the correct one. + +Required properties in the root node: +- compatible value: + compatible = "arm,vexpress,<model>", "arm,vexpress"; + where <model> is the full tile model name (as used in the tile's + Technical Reference Manual), eg.: + - for Coretile Express A5x2 (V2P-CA5s): + compatible = "arm,vexpress,v2p-ca5s", "arm,vexpress"; + - for Coretile Express A9x4 (V2P-CA9): + compatible = "arm,vexpress,v2p-ca9", "arm,vexpress"; + If a tile comes in several variants or can be used in more then one + configuration, the compatible value should be: + compatible = "arm,vexpress,<model>,<variant>", \ + "arm,vexpress,<model>", "arm,vexpress"; + eg: + - Coretile Express A15x2 (V2P-CA15) with Tech Chip 1: + compatible = "arm,vexpress,v2p-ca15,tc1", \ + "arm,vexpress,v2p-ca15", "arm,vexpress"; + - LogicTile Express 13MG (V2F-2XV6) running Cortex-A7 (3 cores) SMM: + compatible = "arm,vexpress,v2f-2xv6,ca7x3", \ + "arm,vexpress,v2f-2xv6", "arm,vexpress"; + +Optional properties in the root node: +- tile model name (use name from the tile's Technical Reference + Manual, eg. "V2P-CA5s") + model = "<model>"; +- tile's HBI number (unique ARM's board model ID, visible on the + PCB's silkscreen) in hexadecimal transcription: + arm,hbi = <0xhbi> + eg: + - for Coretile Express A5x2 (V2P-CA5s) HBI-0191: + arm,hbi = <0x191>; + - Coretile Express A9x4 (V2P-CA9) HBI-0225: + arm,hbi = <0x225>; + +Top-level standard "cpus" node is required. It must contain a node +with device_type = "cpu" property for every available core, eg.: + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a5"; + reg = <0>; + }; + }; + +The motherboard description file provides a single "motherboard" node +using 2 address cells corresponding to the Static Memory Bus used +between the motherboard and the tile. The first cell defines the Chip +Select (CS) line number, the second cell address offset within the CS. +All interrupt lines between the motherboard and the tile are active +high and are described using single cell. + +Optional properties of the "motherboard" node: +- motherboard's memory map variant: + arm,v2m-memory-map = "<name>"; + where name is one of: + - "rs1" - for RS1 map (i.a. peripherals on CS3); this map is also + referred to as "ARM Cortex-A Series memory map": + arm,v2m-memory-map = "rs1"; + When this property is missing, the motherboard is using the original + memory map (also known as the "Legacy memory map", primarily used + with the original CoreTile Express A9x4) with peripherals on CS7. + +Motherboard .dtsi files provide a set of labelled peripherals that +can be used to obtain required phandle in the tile's "aliases" node: +- UARTs, note that the numbers correspond to the physical connectors + on the motherboard's back panel: + v2m_serial0, v2m_serial1, v2m_serial2 and v2m_serial3 +- I2C controllers: + v2m_i2c_dvi and v2m_i2c_pcie +- SP804 timers: + v2m_timer01 and v2m_timer23 + +Current Linux implementation requires a "arm,v2m_timer" alias +pointing at one of the motherboard's SP804 timers, if it is to be +used as the system timer. This alias should be defined in the +motherboard files. + +The tile description must define "ranges", "interrupt-map-mask" and +"interrupt-map" properties to translate the motherboard's address +and interrupt space into one used by the tile's processor. + +Abbreviated example: + +/dts-v1/; + +/ { + model = "V2P-CA5s"; + arm,hbi = <0x225>; + compatible = "arm,vexpress-v2p-ca5s", "arm,vexpress"; + interrupt-parent = <&gic>; + #address-cells = <1>; + #size-cells = <1>; + + chosen { }; + + aliases { + serial0 = &v2m_serial0; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a5"; + reg = <0>; + }; + }; + + gic: interrupt-controller@2c001000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <0>; + interrupt-controller; + reg = <0x2c001000 0x1000>, + <0x2c000100 0x100>; + }; + + motherboard { + /* CS0 is visible at 0x08000000 */ + ranges = <0 0 0x08000000 0x04000000>; + interrupt-map-mask = <0 0 63>; + /* Active high IRQ 0 is connected to GIC's SPI0 */ + interrupt-map = <0 0 0 &gic 0 0 4>; + }; +}; + +/include/ "vexpress-v2m-rs1.dtsi" diff --git a/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt b/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt new file mode 100644 index 0000000..90fa7da --- /dev/null +++ b/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt @@ -0,0 +1,30 @@ +* NVIDIA Tegra APB DMA controller + +Required properties: +- compatible: Should be "nvidia,<chip>-apbdma" +- reg: Should contain DMA registers location and length. This shuld include + all of the per-channel registers. +- interrupts: Should contain all of the per-channel DMA interrupts. + +Examples: + +apbdma: dma@6000a000 { + compatible = "nvidia,tegra20-apbdma"; + reg = <0x6000a000 0x1200>; + interrupts = < 0 136 0x04 + 0 137 0x04 + 0 138 0x04 + 0 139 0x04 + 0 140 0x04 + 0 141 0x04 + 0 142 0x04 + 0 143 0x04 + 0 144 0x04 + 0 145 0x04 + 0 146 0x04 + 0 147 0x04 + 0 148 0x04 + 0 149 0x04 + 0 150 0x04 + 0 151 0x04 >; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt new file mode 100644 index 0000000..16695d9 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt @@ -0,0 +1,23 @@ +twl4030 GPIO controller bindings + +Required properties: +- compatible: + - "ti,twl4030-gpio" for twl4030 GPIO controller +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify optional parameters (unused) +- gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. +- interrupt-controller: Mark the device node as an interrupt controller + The first cell is the GPIO number. + The second cell is not used. + +Example: + +twl_gpio: gpio { + compatible = "ti,twl4030-gpio"; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt new file mode 100644 index 0000000..66efc80 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt @@ -0,0 +1,20 @@ +* Atmel GPIO controller (PIO) + +Required properties: +- compatible: "atmel,<chip>-gpio", where <chip> is at91rm9200 or at91sam9x5. +- reg: Should contain GPIO controller registers location and length +- interrupts: Should be the port interrupt shared by all the pins. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). +- gpio-controller: Marks the device node as a GPIO controller. + +Example: + pioA: gpio@fffff200 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff200 0x100>; + interrupts = <2 4>; + #gpio-cells = <2>; + gpio-controller; + }; + diff --git a/Documentation/devicetree/bindings/gpio/gpio_i2c.txt b/Documentation/devicetree/bindings/gpio/gpio_i2c.txt new file mode 100644 index 0000000..4f8ec94 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_i2c.txt @@ -0,0 +1,32 @@ +Device-Tree bindings for i2c gpio driver + +Required properties: + - compatible = "i2c-gpio"; + - gpios: sda and scl gpio + + +Optional properties: + - i2c-gpio,sda-open-drain: sda as open drain + - i2c-gpio,scl-open-drain: scl as open drain + - i2c-gpio,scl-output-only: scl as output only + - i2c-gpio,delay-us: delay between GPIO operations (may depend on each platform) + - i2c-gpio,timeout-ms: timeout to get data + +Example nodes: + +i2c@0 { + compatible = "i2c-gpio"; + gpios = <&pioA 23 0 /* sda */ + &pioA 24 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + + rv3029c2@56 { + compatible = "rv3029c2"; + reg = <0x56>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt index eb4b530..023c952 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt +++ b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt @@ -1,8 +1,40 @@ -NVIDIA Tegra 2 GPIO controller +NVIDIA Tegra GPIO controller Required properties: -- compatible : "nvidia,tegra20-gpio" +- compatible : "nvidia,tegra<chip>-gpio" +- reg : Physical base address and length of the controller's registers. +- interrupts : The interrupt outputs from the controller. For Tegra20, + there should be 7 interrupts specified, and for Tegra30, there should + be 8 interrupts specified. - #gpio-cells : Should be two. The first cell is the pin number and the second cell is used to specify optional parameters: - bit 0 specifies polarity (0 for normal, 1 for inverted) - gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. + The first cell is the GPIO number. + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + Valid combinations are 1, 2, 3, 4, 8. +- interrupt-controller : Marks the device node as an interrupt controller. + +Example: + +gpio: gpio@6000d000 { + compatible = "nvidia,tegra20-gpio"; + reg = < 0x6000d000 0x1000 >; + interrupts = < 0 32 0x04 + 0 33 0x04 + 0 34 0x04 + 0 35 0x04 + 0 55 0x04 + 0 87 0x04 + 0 89 0x04 >; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt new file mode 100644 index 0000000..1e34cfe --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -0,0 +1,23 @@ +* Marvell PXA GPIO controller + +Required properties: +- compatible : Should be "mrvl,pxa-gpio" or "mrvl,mmp-gpio" +- reg : Address and length of the register set for the device +- interrupts : Should be the port interrupt shared by all gpio pins, if +- interrupt-name : Should be the name of irq resource. + one number. +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be one. It is the pin number. + +Example: + + gpio: gpio@d4019000 { + compatible = "mrvl,mmp-gpio", "mrvl,pxa-gpio"; + reg = <0xd4019000 0x1000>; + interrupts = <49>, <17>, <18>; + interrupt-name = "gpio_mux", "gpio0", "gpio1"; + gpio-controller; + #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt new file mode 100644 index 0000000..071eb3c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt @@ -0,0 +1,37 @@ +* I2C + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "mrvl,mmp-twsi" where CHIP is the name of a + compatible processor, e.g. pxa168, pxa910, mmp2, mmp3. + For the pxa2xx/pxa3xx, an additional node "mrvl,pxa-i2c" is required + as shown in the example below. + +Recommended properties : + + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - mrvl,i2c-polling : Disable interrupt of i2c controller. Polling + status register of i2c controller instead. + - mrvl,i2c-fast-mode : Enable fast mode of i2c controller. + +Examples: + twsi1: i2c@d4011000 { + compatible = "mrvl,mmp-twsi", "mrvl,pxa-i2c"; + reg = <0xd4011000 0x1000>; + interrupts = <7>; + mrvl,i2c-fast-mode; + }; + + twsi2: i2c@d4025000 { + compatible = "mrvl,mmp-twsi", "mrvl,pxa-i2c"; + reg = <0xd4025000 0x1000>; + interrupts = <58>; + }; + diff --git a/Documentation/devicetree/bindings/i2c/sirf-i2c.txt b/Documentation/devicetree/bindings/i2c/sirf-i2c.txt new file mode 100644 index 0000000..7baf9e1 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/sirf-i2c.txt @@ -0,0 +1,19 @@ +I2C for SiRFprimaII platforms + +Required properties : +- compatible : Must be "sirf,prima2-i2c" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt number to the cpu. + +Optional properties: +- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. + The absence of the propoerty indicates the default frequency 100 kHz. + +Examples : + +i2c0: i2c@b00e0000 { + compatible = "sirf,prima2-i2c"; + reg = <0xb00e0000 0x10000>; + interrupts = <24>; +}; diff --git a/Documentation/devicetree/bindings/input/matrix-keymap.txt b/Documentation/devicetree/bindings/input/matrix-keymap.txt new file mode 100644 index 0000000..3cd8b98 --- /dev/null +++ b/Documentation/devicetree/bindings/input/matrix-keymap.txt @@ -0,0 +1,19 @@ +A simple common binding for matrix-connected key boards. Currently targeted at +defining the keys in the scope of linux key codes since that is a stable and +standardized interface at this time. + +Required properties: +- linux,keymap: an array of packed 1-cell entries containing the equivalent + of row, column and linux key-code. The 32-bit big endian cell is packed + as: + row << 24 | column << 16 | key-code + +Optional properties: +Some users of this binding might choose to specify secondary keymaps for +cases where there is a modifier key such as a Fn key. Proposed names +for said properties are "linux,fn-keymap" or with another descriptive +word for the modifier other from "Fn". + +Example: + linux,keymap = < 0x00030012 + 0x0102003a >; diff --git a/Documentation/devicetree/bindings/input/tegra-kbc.txt b/Documentation/devicetree/bindings/input/tegra-kbc.txt index 5ecfa99..72683be 100644 --- a/Documentation/devicetree/bindings/input/tegra-kbc.txt +++ b/Documentation/devicetree/bindings/input/tegra-kbc.txt @@ -3,16 +3,21 @@ Required properties: - compatible: "nvidia,tegra20-kbc" -Optional properties: -- debounce-delay: delay in milliseconds per row scan for debouncing -- repeat-delay: delay in milliseconds before repeat starts -- ghost-filter: enable ghost filtering for this device -- wakeup-source: configure keyboard as a wakeup source for suspend/resume +Optional properties, in addition to those specified by the shared +matrix-keyboard bindings: + +- linux,fn-keymap: a second keymap, same specification as the + matrix-keyboard-controller spec but to be used when the KEY_FN modifier + key is pressed. +- nvidia,debounce-delay-ms: delay in milliseconds per row scan for debouncing +- nvidia,repeat-delay-ms: delay in milliseconds before repeat starts +- nvidia,ghost-filter: enable ghost filtering for this device +- nvidia,wakeup-source: configure keyboard as a wakeup source for suspend/resume Example: keyboard: keyboard { compatible = "nvidia,tegra20-kbc"; reg = <0x7000e200 0x100>; - ghost-filter; + nvidia,ghost-filter; }; diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt new file mode 100644 index 0000000..5903ecf --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -0,0 +1,41 @@ +Atmel NAND flash + +Required properties: +- compatible : "atmel,at91rm9200-nand". +- reg : should specify localbus address and size used for the chip, + and if availlable the ECC. +- atmel,nand-addr-offset : offset for the address latch. +- atmel,nand-cmd-offset : offset for the command latch. +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. + +- gpios : specifies the gpio pins to control the NAND device. detect is an + optional gpio and may be set to 0 if not present. + +Optional properties: +- nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default. + Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", + "soft_bch". +- nand-bus-width : 8 or 16 bus width if not present 8 +- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false + +Examples: +nand0: nand@40000000,0 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000 + 0xffffe800 0x200 + >; + atmel,nand-addr-offset = <21>; + atmel,nand-cmd-offset = <22>; + nand-on-flash-bbt; + nand-ecc-mode = "soft"; + gpios = <&pioC 13 0 + &pioC 14 0 + 0 + >; + partition@0 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt new file mode 100644 index 0000000..03855c8 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/nand.txt @@ -0,0 +1,7 @@ +* MTD generic binding + +- nand-ecc-mode : String, operation mode of the NAND ecc mode. + Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", + "soft_bch". +- nand-bus-width : 8 or 16 bus width if not present 8 +- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt new file mode 100644 index 0000000..1f62623 --- /dev/null +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -0,0 +1,28 @@ +* STMicroelectronics 10/100/1000 Ethernet driver (GMAC) + +Required properties: +- compatible: Should be "st,spear600-gmac" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the STMMAC interrupts +- interrupt-names: Should contain the interrupt names "macirq" + "eth_wake_irq" if this interrupt is supported in the "interrupts" + property +- phy-mode: String, operation mode of the PHY interface. + Supported values are: "mii", "rmii", "gmii", "rgmii". + +Optional properties: +- mac-address: 6 bytes, mac address + +Examples: + + gmac0: ethernet@e0800000 { + compatible = "st,spear600-gmac"; + reg = <0xe0800000 0x8000>; + interrupt-parent = <&vic1>; + interrupts = <24 23>; + interrupt-names = "macirq", "eth_wake_irq"; + mac-address = [000000000000]; /* Filled in by U-Boot */ + phy-mode = "gmii"; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic-msgr.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic-msgr.txt new file mode 100644 index 0000000..bc8ded6 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic-msgr.txt @@ -0,0 +1,63 @@ +* FSL MPIC Message Registers + +This binding specifies what properties must be available in the device tree +representation of the message register blocks found in some FSL MPIC +implementations. + +Required properties: + + - compatible: Specifies the compatibility list for the message register + block. The type shall be <string-list> and the value shall be of the form + "fsl,mpic-v<version>-msgr", where <version> is the version number of + the MPIC containing the message registers. + + - reg: Specifies the base physical address(s) and size(s) of the + message register block's addressable register space. The type shall be + <prop-encoded-array>. + + - interrupts: Specifies a list of interrupt-specifiers which are available + for receiving interrupts. Interrupt-specifier consists of two cells: first + cell is interrupt-number and second cell is level-sense. The type shall be + <prop-encoded-array>. + +Optional properties: + + - mpic-msgr-receive-mask: Specifies what registers in the containing block + are allowed to receive interrupts. The value is a bit mask where a set + bit at bit 'n' indicates that message register 'n' can receive interrupts. + Note that "bit 'n'" is numbered from LSB for PPC hardware. The type shall + be <u32>. If not present, then all of the message registers in the block + are available. + +Aliases: + + An alias should be created for every message register block. They are not + required, though. However, a particular implementation of this binding + may require aliases to be present. Aliases are of the form + 'mpic-msgr-block<n>', where <n> is an integer specifying the block's number. + Numbers shall start at 0. + +Example: + + aliases { + mpic-msgr-block0 = &mpic_msgr_block0; + mpic-msgr-block1 = &mpic_msgr_block1; + }; + + mpic_msgr_block0: mpic-msgr-block@41400 { + compatible = "fsl,mpic-v3.1-msgr"; + reg = <0x41400 0x200>; + // Message registers 0 and 2 in this block can receive interrupts on + // sources 0xb0 and 0xb2, respectively. + interrupts = <0xb0 2 0xb2 2>; + mpic-msgr-receive-mask = <0x5>; + }; + + mpic_msgr_block1: mpic-msgr-block@42400 { + compatible = "fsl,mpic-v3.1-msgr"; + reg = <0x42400 0x200>; + // Message registers 0 and 2 in this block can receive interrupts on + // sources 0xb4 and 0xb6, respectively. + interrupts = <0xb4 2 0xb6 2>; + mpic-msgr-receive-mask = <0x5>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt index 2cf38bd..dc57446 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt @@ -56,7 +56,27 @@ PROPERTIES to the client. The presence of this property also mandates that any initialization related to interrupt sources shall be limited to sources explicitly referenced in the device tree. - + + - big-endian + Usage: optional + Value type: <empty> + If present the MPIC will be assumed to be big-endian. Some + device-trees omit this property on MPIC nodes even when the MPIC is + in fact big-endian, so certain boards override this property. + + - single-cpu-affinity + Usage: optional + Value type: <empty> + If present the MPIC will be assumed to only be able to route + non-IPI interrupts to a single CPU at a time (EG: Freescale MPIC). + + - last-interrupt-source + Usage: optional + Value type: <u32> + Some MPICs do not correctly report the number of hardware sources + in the global feature registers. If specified, this field will + override the value read from MPIC_GREG_FEATURE_LAST_SRC. + INTERRUPT SPECIFIER DEFINITION Interrupt specifiers consists of 4 cells encoded as diff --git a/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt index 5d586e1..5693877 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt @@ -6,8 +6,10 @@ Required properties: etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on the parent type. -- reg : should contain the address and the length of the shared message - interrupt register set. +- reg : It may contain one or two regions. The first region should contain + the address and the length of the shared message interrupt register set. + The second region should contain the address of aliased MSIIR register for + platforms that have such an alias. - msi-available-ranges: use <start count> style section to define which msi interrupt can be used in the 256 msi interrupts. This property is diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt new file mode 100644 index 0000000..0c3395d --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt @@ -0,0 +1,68 @@ +TWL family of regulators + +Required properties: +For twl6030 regulators/LDOs +- compatible: + - "ti,twl6030-vaux1" for VAUX1 LDO + - "ti,twl6030-vaux2" for VAUX2 LDO + - "ti,twl6030-vaux3" for VAUX3 LDO + - "ti,twl6030-vmmc" for VMMC LDO + - "ti,twl6030-vpp" for VPP LDO + - "ti,twl6030-vusim" for VUSIM LDO + - "ti,twl6030-vana" for VANA LDO + - "ti,twl6030-vcxio" for VCXIO LDO + - "ti,twl6030-vdac" for VDAC LDO + - "ti,twl6030-vusb" for VUSB LDO + - "ti,twl6030-v1v8" for V1V8 LDO + - "ti,twl6030-v2v1" for V2V1 LDO + - "ti,twl6030-clk32kg" for CLK32KG RESOURCE + - "ti,twl6030-vdd1" for VDD1 SMPS + - "ti,twl6030-vdd2" for VDD2 SMPS + - "ti,twl6030-vdd3" for VDD3 SMPS +For twl6025 regulators/LDOs +- compatible: + - "ti,twl6025-ldo1" for LDO1 LDO + - "ti,twl6025-ldo2" for LDO2 LDO + - "ti,twl6025-ldo3" for LDO3 LDO + - "ti,twl6025-ldo4" for LDO4 LDO + - "ti,twl6025-ldo5" for LDO5 LDO + - "ti,twl6025-ldo6" for LDO6 LDO + - "ti,twl6025-ldo7" for LDO7 LDO + - "ti,twl6025-ldoln" for LDOLN LDO + - "ti,twl6025-ldousb" for LDOUSB LDO + - "ti,twl6025-smps3" for SMPS3 SMPS + - "ti,twl6025-smps4" for SMPS4 SMPS + - "ti,twl6025-vio" for VIO SMPS +For twl4030 regulators/LDOs +- compatible: + - "ti,twl4030-vaux1" for VAUX1 LDO + - "ti,twl4030-vaux2" for VAUX2 LDO + - "ti,twl5030-vaux2" for VAUX2 LDO + - "ti,twl4030-vaux3" for VAUX3 LDO + - "ti,twl4030-vaux4" for VAUX4 LDO + - "ti,twl4030-vmmc1" for VMMC1 LDO + - "ti,twl4030-vmmc2" for VMMC2 LDO + - "ti,twl4030-vpll1" for VPLL1 LDO + - "ti,twl4030-vpll2" for VPLL2 LDO + - "ti,twl4030-vsim" for VSIM LDO + - "ti,twl4030-vdac" for VDAC LDO + - "ti,twl4030-vintana2" for VINTANA2 LDO + - "ti,twl4030-vio" for VIO LDO + - "ti,twl4030-vdd1" for VDD1 SMPS + - "ti,twl4030-vdd2" for VDD2 SMPS + - "ti,twl4030-vintana1" for VINTANA1 LDO + - "ti,twl4030-vintdig" for VINTDIG LDO + - "ti,twl4030-vusb1v5" for VUSB1V5 LDO + - "ti,twl4030-vusb1v8" for VUSB1V8 LDO + - "ti,twl4030-vusb3v1" for VUSB3V1 LDO + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: + + xyz: regulator@0 { + compatible = "ti,twl6030-vaux1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + }; diff --git a/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt b/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt new file mode 100644 index 0000000..0cda19a --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt @@ -0,0 +1,17 @@ +* Marvell Real Time Clock controller + +Required properties: +- compatible: should be "mrvl,sa1100-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: Should be two. The first interrupt number is the rtc alarm + interrupt and the second interrupt number is the rtc hz interrupt. +- interrupt-names: Assign name of irq resource. + +Example: + rtc: rtc@d4010000 { + compatible = "mrvl,mmp-rtc"; + reg = <0xd4010000 0x1000>; + interrupts = <5>, <6>; + interrupt-name = "rtc 1Hz", "rtc alarm"; + }; diff --git a/Documentation/devicetree/bindings/serial/mrvl-serial.txt b/Documentation/devicetree/bindings/serial/mrvl-serial.txt new file mode 100644 index 0000000..d744340 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/mrvl-serial.txt @@ -0,0 +1,4 @@ +PXA UART controller + +Required properties: +- compatible : should be "mrvl,mmp-uart" or "mrvl,pxa-uart". diff --git a/Documentation/devicetree/bindings/sound/alc5632.txt b/Documentation/devicetree/bindings/sound/alc5632.txt new file mode 100644 index 0000000..8608f74 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/alc5632.txt @@ -0,0 +1,24 @@ +ALC5632 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "realtek,alc5632" + + - reg : the I2C address of the device. + + - gpio-controller : Indicates this device is a GPIO controller. + + - #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + +Example: + +alc5632: alc5632@1e { + compatible = "realtek,alc5632"; + reg = <0x1a>; + + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/sound/imx-audmux.txt b/Documentation/devicetree/bindings/sound/imx-audmux.txt new file mode 100644 index 0000000..215aa98 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/imx-audmux.txt @@ -0,0 +1,13 @@ +Freescale Digital Audio Mux (AUDMUX) device + +Required properties: +- compatible : "fsl,imx21-audmux" for AUDMUX version firstly used on i.MX21, + or "fsl,imx31-audmux" for the version firstly used on i.MX31. +- reg : Should contain AUDMUX registers location and length + +Example: + +audmux@021d8000 { + compatible = "fsl,imx6q-audmux", "fsl,imx31-audmux"; + reg = <0x021d8000 0x4000>; +}; diff --git a/Documentation/devicetree/bindings/sound/soc/codecs/fsl-sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 2c3cd41..2c3cd41 100644 --- a/Documentation/devicetree/bindings/sound/soc/codecs/fsl-sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt diff --git a/Documentation/devicetree/bindings/sound/tegra-audio-alc5632.txt b/Documentation/devicetree/bindings/sound/tegra-audio-alc5632.txt new file mode 100644 index 0000000..b77a97c --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tegra-audio-alc5632.txt @@ -0,0 +1,59 @@ +NVIDIA Tegra audio complex + +Required properties: +- compatible : "nvidia,tegra-audio-alc5632" +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the ALC5632's pins: + + ALC5632 pins: + + * SPK_OUTP + * SPK_OUTN + * HP_OUT_L + * HP_OUT_R + * AUX_OUT_P + * AUX_OUT_N + * LINE_IN_L + * LINE_IN_R + * PHONE_P + * PHONE_N + * MIC1_P + * MIC1_N + * MIC2_P + * MIC2_N + * MICBIAS1 + * DMICDAT + + Board connectors: + + * Headset Stereophone + * Int Spk + * Headset Mic + * Digital Mic + +- nvidia,i2s-controller : The phandle of the Tegra I2S controller +- nvidia,audio-codec : The phandle of the ALC5632 audio codec + +Example: + +sound { + compatible = "nvidia,tegra-audio-alc5632-paz00", + "nvidia,tegra-audio-alc5632"; + + nvidia,model = "Compal PAZ00"; + + nvidia,audio-routing = + "Int Spk", "SPK_OUTP", + "Int Spk", "SPK_OUTN", + "Headset Mic","MICBIAS1", + "MIC1_N", "Headset Mic", + "MIC1_P", "Headset Mic", + "Headset Stereophone", "HP_OUT_R", + "Headset Stereophone", "HP_OUT_L"; + + nvidia,i2s-controller = <&tegra_i2s1>; + nvidia,audio-codec = <&alc5632>; +}; diff --git a/Documentation/devicetree/bindings/spi/omap-spi.txt b/Documentation/devicetree/bindings/spi/omap-spi.txt new file mode 100644 index 0000000..81df374 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/omap-spi.txt @@ -0,0 +1,20 @@ +OMAP2+ McSPI device + +Required properties: +- compatible : + - "ti,omap2-spi" for OMAP2 & OMAP3. + - "ti,omap4-spi" for OMAP4+. +- ti,spi-num-cs : Number of chipselect supported by the instance. +- ti,hwmods: Name of the hwmod associated to the McSPI + + +Example: + +mcspi1: mcspi@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,omap4-mcspi"; + ti,hwmods = "mcspi1"; + ti,spi-num-cs = <4>; +}; + diff --git a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt new file mode 100644 index 0000000..6588b69 --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt @@ -0,0 +1,14 @@ +* Energymicro efm32 UART + +Required properties: +- compatible : Should be "efm32,uart" +- reg : Address and length of the register set +- interrupts : Should contain uart interrupt + +Example: + +uart@0x4000c400 { + compatible = "efm32,uart"; + reg = <0x4000c400 0x400>; + interrupts = <15>; +}; diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt new file mode 100644 index 0000000..60bd215 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt @@ -0,0 +1,49 @@ +Atmel SOC USB controllers + +OHCI + +Required properties: + - compatible: Should be "atmel,at91rm9200-ohci" for USB controllers + used in host mode. + - num-ports: Number of ports. + - atmel,vbus-gpio: If present, specifies a gpio that needs to be + activated for the bus to be powered. + - atmel,oc-gpio: If present, specifies a gpio that needs to be + activated for the overcurrent detection. + +usb0: ohci@00500000 { + compatible = "atmel,at91rm9200-ohci", "usb-ohci"; + reg = <0x00500000 0x100000>; + interrupts = <20 4>; + num-ports = <2>; +}; + +EHCI + +Required properties: + - compatible: Should be "atmel,at91sam9g45-ehci" for USB controllers + used in host mode. + +usb1: ehci@00800000 { + compatible = "atmel,at91sam9g45-ehci", "usb-ehci"; + reg = <0x00800000 0x100000>; + interrupts = <22 4>; +}; + +AT91 USB device controller + +Required properties: + - compatible: Should be "atmel,at91rm9200-udc" + - reg: Address and length of the register set for the device + - interrupts: Should contain macb interrupt + +Optional properties: + - atmel,vbus-gpio: If present, specifies a gpio that needs to be + activated for the bus to be powered. + +usb1: gadget@fffa4000 { + compatible = "atmel,at91rm9200-udc"; + reg = <0xfffa4000 0x4000>; + interrupts = <10 4>; + atmel,vbus-gpio = <&pioC 5 0>; +}; diff --git a/Documentation/devicetree/bindings/usb/tegra-usb.txt b/Documentation/devicetree/bindings/usb/tegra-usb.txt index 035d63d..007005d 100644 --- a/Documentation/devicetree/bindings/usb/tegra-usb.txt +++ b/Documentation/devicetree/bindings/usb/tegra-usb.txt @@ -11,3 +11,16 @@ Required properties : - phy_type : Should be one of "ulpi" or "utmi". - nvidia,vbus-gpio : If present, specifies a gpio that needs to be activated for the bus to be powered. + +Optional properties: + - dr_mode : dual role mode. Indicates the working mode for + nvidia,tegra20-ehci compatible controllers. Can be "host", "peripheral", + or "otg". Default to "host" if not defined for backward compatibility. + host means this is a host controller + peripheral means it is device controller + otg means it can operate as either ("on the go") + - nvidia,has-legacy-mode : boolean indicates whether this controller can + operate in legacy mode (as APX 2500 / 2600). In legacy mode some + registers are accessed through the APB_MISC base address instead of + the USB controller. Since this is a legacy issue it probably does not + warrant a compatible string of its own. diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index a20008a..82ac057 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -34,6 +34,7 @@ picochip Picochip Ltd powervr Imagination Technologies qcom Qualcomm, Inc. ramtron Ramtron International +realtek Realtek Semiconductor Corp. samsung Samsung Semiconductor sbs Smart Battery System schindler Schindler diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt index 7c1329d..da0bfeb 100644 --- a/Documentation/devicetree/booting-without-of.txt +++ b/Documentation/devicetree/booting-without-of.txt @@ -169,7 +169,7 @@ it with special cases. b) Entry with a flattened device-tree block. Firmware loads the physical address of the flattened device tree block (dtb) into r2, - r1 is not used, but it is considered good practise to use a valid + r1 is not used, but it is considered good practice to use a valid machine number as described in Documentation/arm/Booting. r0 : 0 |