diff options
Diffstat (limited to 'arch/m68knommu/Kconfig')
| -rw-r--r-- | arch/m68knommu/Kconfig | 131 |
1 files changed, 97 insertions, 34 deletions
diff --git a/arch/m68knommu/Kconfig b/arch/m68knommu/Kconfig index 6c6980b..e767f2d 100644 --- a/arch/m68knommu/Kconfig +++ b/arch/m68knommu/Kconfig @@ -472,38 +472,46 @@ config 4KSTACKS running more threads on a system and also reduces the pressure on the VM subsystem for higher order allocations. -choice - prompt "RAM size" - default AUTO - -config RAMAUTO - bool "AUTO" - ---help--- - Configure the RAM size on your platform. Many platforms can auto - detect this, on those choose the AUTO option. Otherwise set the - RAM size you intend using. - -config RAM4MB - bool "4MiB" - help - Set RAM size to be 4MiB. - -config RAM8MB - bool "8MiB" - help - Set RAM size to be 8MiB. - -config RAM16MB - bool "16MiB" - help - Set RAM size to be 16MiB. - -config RAM32MB - bool "32MiB" - help - Set RAM size to be 32MiB. - -endchoice +comment "RAM configuration" + +config RAMBASE + hex "Address of the base of RAM" + default "0" + help + Define the address that RAM starts at. On many platforms this is + 0, the base of the address space. And this is the default. Some + platforms choose to setup their RAM at other addresses within the + processor address space. + +config RAMSIZE + hex "Size of RAM (in bytes)" + default "0x400000" + help + Define the size of the system RAM. If you select 0 then the + kernel will try to probe the RAM size at runtime. This is not + supported on all CPU types. + +config VECTORBASE + hex "Address of the base of system vectors" + default "0" + help + Define the address of the the system vectors. Commonly this is + put at the start of RAM, but it doesn't have to be. On ColdFire + platforms this address is programmed into the VBR register, thus + actually setting the address to use. + +config KERNELBASE + hex "Address of the base of kernel code" + default "0x400" + help + Typically on m68k systems the kernel will not start at the base + of RAM, but usually some small offset from it. Define the start + address of the kernel here. The most common setup will have the + processor vectors at the base of RAM and then the start of the + kernel. On some platforms some RAM is reserved for boot loaders + and the kernel starts after that. The 0x400 default was based on + a system with the RAM based at address 0, and leaving enough room + for the theoretical maximum number of 256 vectors. choice prompt "RAM bus width" @@ -511,7 +519,7 @@ choice config RAMAUTOBIT bool "AUTO" - ---help--- + help Select the physical RAM data bus size. Not needed on most platforms, so you can generally choose AUTO. @@ -532,6 +540,59 @@ config RAM32BIT endchoice +comment "ROM configuration" + +config ROM + bool "Specify ROM linker regions" + default n + help + Define a ROM region for the linker script. This creates a kernel + that can be stored in flash, with possibly the text, and data + regions being copied out to RAM at startup. + +config ROMBASE + hex "Address of the base of ROM device" + default "0" + depends on ROM + help + Define the address that the ROM region starts at. Some platforms + use this to set their chip select region accordingly for the boot + device. + +config ROMVEC + hex "Address of the base of the ROM vectors" + default "0" + depends on ROM + help + This is almost always the same as the base of the ROM. Since on all + 68000 type varients the vectors are at the base of the boot device + on system startup. + +config ROMVECSIZE + hex "Size of ROM vector region (in bytes)" + default "0x400" + depends on ROM + help + Define the size of the vector region in ROM. For most 68000 + varients this would be 0x400 bytes in size. Set to 0 if you do + not want a vector region at the start of the ROM. + +config ROMSTART + hex "Address of the base of system image in ROM" + default "0x400" + depends on ROM + help + Define the start address of the system image in ROM. Commonly this + is strait after the ROM vectors. + +config ROMSIZE + hex "Size of the ROM device" + default "0x100000" + depends on ROM + help + Size of the ROM device. On some platforms this is used to setup + the chip select that controls the boot ROM device. + choice prompt "Kernel executes from" ---help--- @@ -545,7 +606,9 @@ config RAMKERNEL config ROMKERNEL bool "ROM" help - The kernel will be resident in FLASH/ROM when running. + The kernel will be resident in FLASH/ROM when running. This is + often referred to as Execute-in-Place (XIP), since the kernel + code executes from the position it is stored in the FLASH/ROM. endchoice |