aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/mfd
Commit message (Collapse)AuthorAgeFilesLines
* mfd: Put WM8994 into cache only mode when suspendingMark Brown2012-01-091-0/+2
| | | | | | | This is required by the ASoC driver for very low power modes where the device is fully idle but we want to update controls. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* mfd: Test for jack detection when deciding if wm8994 should suspendMark Brown2011-12-141-0/+14
| | | | | | | | The jack detection on WM1811 is often required during system suspend, add it as another check when deciding if we should suspend. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Convert wm8994 to use generic regmap irq_chipMark Brown2011-12-132-163/+34
| | | | | | | | Factor out the irq_chip implementation, substantially reducing the code size for the driver. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Mark WM1811 GPIO6 register volatile for later revisionsMark Brown2011-12-132-7/+24
| | | | | | | | | For later chip revisions the WM1811 GPIO6 register is always volatile so store the device revision when initialising the driver and then check at runtime if we're running on a newer device. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Add WM1811A device ID to wm8994 driverMark Brown2011-12-131-0/+1
| | | | | | | The WM1811A is a variant of the WM1811 with pin configuration changes. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Correct revision display for WM1811 revision DMark Brown2011-12-131-0/+5
| | | | | | | | | As WM1811 revision C was transparent to software the revision IDs for subsequent revisions are one less than they would normally be. Correct for this in log messages. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Initialise WM8994 register cache after reading chip ID registersMark Brown2011-12-133-17/+30
| | | | | | | | | | | The different devices handled by the WM8994 can be distinguished using their ID registers so we don't need to rely on the user having registered the device correctly. Instead do the initial regmap setup with a minimal configuration only supporting physical I/O and then configure the cache once we have identified the device. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Enable register cache for wm8994 devicesMark Brown2011-12-131-52/+30
| | | | | | | | | As part of this we provide information about the registers that exist in the device to the regmap core, drop the small amount of cache that the core had been using and let regmap do the sync. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Add wm8994 register access and default informationMark Brown2011-12-133-1/+1243
| | | | | | | | | | | | | | Describe the register map to the regmap core so that we can use its diagnostic features and cache support. This is split out from the patch using it due to the size so that the actual code change is a bit clearer. As the various devices are supersets of each other the access maps are built up by layering the functions on top of each other, though the interface for specifying the register defaults isn't currently amenable to this. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Don't hard code the reset value for WM8994 devicesMark Brown2011-12-131-1/+2
| | | | | Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Disable more pulls on WM8994Mark Brown2011-12-131-3/+8
| | | | | | | | | Disable more pulls by default on WM8994 for a small current saving. Since some designs do leave SPKMODE floating provide platform data to allow that to be left enabled. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Convert wm8994 to devm_kzalloc()Mark Brown2011-12-131-11/+5
| | | | | Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Add basic device tree binding for wm8994Mark Brown2011-12-131-0/+9
| | | | | | | | | Add a placeholder device tree binding for the wm8994 driver. At present the binding is essentially null as none of the platform data is supported, and at least some of that will depend on the pending regulator bindings. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Remove some unused functions in wm8894-irqMark Brown2011-12-131-10/+0
| | | | | Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Oritz <sameo@linux.intel.com>
* mfd: fix build failures in recently added ab5500 codePaul Gortmaker2011-11-072-0/+2
| | | | | | | | | These files had implicit dependencies on modular support which now show up as build failures with the module cleanup work merged to mainline. Reported-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* Merge branch 'modsplit-Oct31_2011' of ↵Linus Torvalds2011-11-0614-0/+14
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux * 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits) Revert "tracing: Include module.h in define_trace.h" irq: don't put module.h into irq.h for tracking irqgen modules. bluetooth: macroize two small inlines to avoid module.h ip_vs.h: fix implicit use of module_get/module_put from module.h nf_conntrack.h: fix up fallout from implicit moduleparam.h presence include: replace linux/module.h with "struct module" wherever possible include: convert various register fcns to macros to avoid include chaining crypto.h: remove unused crypto_tfm_alg_modname() inline uwb.h: fix implicit use of asm/page.h for PAGE_SIZE pm_runtime.h: explicitly requires notifier.h linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h miscdevice.h: fix up implicit use of lists and types stop_machine.h: fix implicit use of smp.h for smp_processor_id of: fix implicit use of errno.h in include/linux/of.h of_platform.h: delete needless include <linux/module.h> acpi: remove module.h include from platform/aclinux.h miscdevice.h: delete unnecessary inclusion of module.h device_cgroup.h: delete needless include <linux/module.h> net: sch_generic remove redundant use of <linux/module.h> net: inet_timewait_sock doesnt need <linux/module.h> ... Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in - drivers/media/dvb/frontends/dibx000_common.c - drivers/media/video/{mt9m111.c,ov6650.c} - drivers/mfd/ab3550-core.c - include/linux/dmaengine.h
| * mfd: Add export.h for EXPORT_SYMBOL/THIS_MODULE as requiredPaul Gortmaker2011-10-314-0/+4
| | | | | | | | | | | | | | These macros are in <linux/export.h> and will no longer be implicitly everywhere anymore. Fix it up in advance. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
| * mfd: Add module.h to the implicit drivers/mfd usersPaul Gortmaker2011-10-3111-0/+11
| | | | | | | | | | | | | | | | | | With the pending module.h cleanup, these files will fail to compile, unless they explicitly call out the include of this file. [omap-usb-host addition courtesy of Anand Gadiyar <gadiyar@ti.com>] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* | Merge branch 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6Linus Torvalds2011-11-0332-2111/+4039
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits) mfd: Fix missing abx500 header file updates mfd: Add missing <linux/io.h> include to intel_msic x86, mrst: add platform support for MSIC MFD driver mfd: Expose TurnOnStatus in ab8500 sysfs mfd: Remove support for early drop ab8500 chip mfd: Add support for ab8500 v3.3 mfd: Add ab8500 interrupt disable hook mfd: Convert db8500-prcmu panic() into pr_crit() mfd: Refactor db8500-prcmu request_clock() function mfd: Rename db8500-prcmu init function mfd: Fix db5500-prcmu defines mfd: db8500-prcmu voltage domain consumers additions mfd: db8500-prcmu reset code retrieval mfd: db8500-prcmu tweak for modem wakeup mfd: Add db8500-pcmu watchdog accessor functions for watchdog mfd: hwacc power state db8500-prcmu accessor mfd: Add db8500-prcmu accessors for PLL and SGA clock mfd: Move to the new db500 PRCMU API mfd: Create a common interface for dbx500 PRCMU drivers mfd: Initialize DB8500 PRCMU regs ... Fix up trivial conflicts in arch/arm/mach-imx/mach-mx31moboard.c arch/arm/mach-omap2/board-omap3beagle.c arch/arm/mach-u300/include/mach/irqs.h drivers/mfd/wm831x-spi.c
| * mfd: Add missing <linux/io.h> include to intel_msicMika Westerberg2011-10-241-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | Without this header we might get following compilation errors: drivers/mfd/intel_msic.c:303:2: error: implicit declaration of function 'readb' drivers/mfd/intel_msic.c:433:2: error: implicit declaration of function 'ioremap_nocache' drivers/mfd/intel_msic.c:433:17: warning: assignment makes pointer from integer without a cast drivers/mfd/intel_msic.c:455:2: error: implicit declaration of function 'iounmap' Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Expose TurnOnStatus in ab8500 sysfsAndrew Lynn2011-10-241-0/+30
| | | | | | | | | | | | | | | | | | | | | | | | Expose TurnOnStatus (Power key, RTC alarm, Vbus detect, etc) in sysfs. This magic value can be read by system users to determine what caused the platform to turn on last (this) time. Signed-off-by: Andrew Lynn <andrew.lynn@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Reviewed-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Remove support for early drop ab8500 chipMattias Wallin2011-10-241-1/+0
| | | | | | | | | | | | | | | | | | | | | | This patch removes the early drop version of ab8500 which have the really bad version nr 0x0. This chip should not be found in the wild and only exist as ST-Ericsson scrap equipment. Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com> Reviewed-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Add support for ab8500 v3.3Mattias Wallin2011-10-241-0/+1
| | | | | | | | | | | | | | | | | | This patch adds support for ab8500 cut 3, MetalFix 3 or v3.3. Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com> Reviewed-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Add ab8500 interrupt disable hookVirupax Sadashivpetimath2011-10-241-0/+1
| | | | | | | | | | | | | | | | | | | | | | Add the missing interrupt disable hook in the irq_chip callbacks for ab8500. Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Convert db8500-prcmu panic() into pr_crit()Linus Walleij2011-10-241-3/+3
| | | | | | | | | | | | | | | | | | panic() is too heavy for this, indeed the PRCMU is critical for the system but not to the point that we should stop everything, if we can still get a prompt or so. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Refactor db8500-prcmu request_clock() functionLinus Walleij2011-10-241-8/+11
| | | | | | | | | | | | | | | | This refactors the mfd/dbx500-prcmu drivers to use a switch() statement rather than nested if/else-construction. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Rename db8500-prcmu init functionLinus Walleij2011-10-241-2/+2
| | | | | | | | | | | | | | | | This renames the PRCMU clock force initialization function to have a less generic name. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Fix db5500-prcmu definesLinus Walleij2011-10-241-2/+5
| | | | | | | | | | | | | | | | This fixes two erroneous defines for the PLLs and adds new defines for the reset pin controls. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: db8500-prcmu voltage domain consumers additionsBengt Jonsson2011-10-241-1/+51
| | | | | | | | | | | | | | | | | | | | | | | | This rectifies the device name of the MCDE voltage domain regulator consumer and adds a number of other consumers to the voltage domains. Cc: Liam Girdwood <lrg@ti.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: db8500-prcmu reset code retrievalSebastian Rasmussen2011-10-241-0/+11
| | | | | | | | | | | | | | | | | | This implements the reset code retrieval function so we can ipso facto get to know how the system was reset. Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: db8500-prcmu tweak for modem wakeupMattias Nilsson2011-10-241-4/+28
| | | | | | | | | | | | | | | | | | | | | | This is a tweak for the case where the modem goes to sleep while emitting the AC_WAKE_ACK anyway. Also print the modem errors as critical, since they jeopardize the entire platform when they occur. Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Add db8500-pcmu watchdog accessor functions for watchdogJonas Aberg2011-10-241-0/+72
| | | | | | | | | | | | | | | | | | This implements the watchdog accessor functions for the DB8500 PRCMU, making it possible to implement the watchdog driver. Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: hwacc power state db8500-prcmu accessorBengt Jonsson2011-10-241-0/+126
| | | | | | | | | | | | | | | | | | This implements the accessor function for hardware accelerator power state settings. Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Add db8500-prcmu accessors for PLL and SGA clockMattias Nilsson2011-10-241-1/+82
| | | | | | | | | | | | | | | | | | This extends the DB8500 PRCMU driver with accessor calls for the PRCMU PLL and SGA clocks. Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Move to the new db500 PRCMU APIMattias Nilsson2011-10-244-149/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that we have a shared API between the DB8500 and DB5500 PRCMU's, switch to using this neutral API instead. We delete the parts of db8500-prcmu.h that is now PRCMU-neutral, and calls will be diverted to respective driver. Common registers are in dbx500-prcmu-regs.h and common accessors and defines in <linux/mfd/dbx500-prcmu.h> This way we get a a lot more abstraction and code reuse. Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Initialize DB8500 PRCMU regsMattias Nilsson2011-10-241-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | Some clocks may be force enabled when we probe the driver, but they need to be turned off by default so we have a known state. We call this the register initialization function if we need more stuff in there in the future. Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Extend DB8500 PRCMU mailbox defsMattias Nilsson2011-10-241-2/+21
| | | | | | | | | | | | | | | | | | We have a few more mailboxes and fixed messages in the DB8500 PRCMU, update to match the latest specification. Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Refactor DB8500 PRCMU reg accessMattias Nilsson2011-10-242-196/+229
| | | | | | | | | | | | | | | | | | | | | | Instead of carrying around the __PRCMU_BASE in every read or write to the PRCMU registers, move it out to the register definition file and define registers along with their base offset so that the code gets easier to read. Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Fix aat2870 build failure for x86_64Jin Park2011-10-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | Without this fix, we get: error: call to ‘copy_from_user_overflow’ declared with attribute error: copy_from_user() buffer size is not provably correct make[3]: *** [drivers/mfd/aat2870-core.o] Error 1 And this was triggered by commit da417bacc9143b934f1a480a25d0fb2bb648a820 Signed-off-by: Jin Park <jinyoungp@nvidia.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Disable twl6030 IRQ during suspendTodd Poynor2011-10-241-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Module IRQs may still be disabled by DPM at the time the TWL6030 ISR runs, causing handle_simple_irq() to silently do nothing. This may result in missing TWL RTC alarm wakeups, for example, since the RTC child module ISR is not called to ack the IRQ. Disable the TWL6030 IRQ during suspend, enable it at DPM resume time, at which time the child module IRQs will be re-enabled. Signed-off-by: Todd Poynor <toddpoynor@google.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Fix twl6030 lockdep recursion warning on setting wake IRQsTodd Poynor2011-10-241-2/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | LOCKDEP explicitly sets all irq_desc locks as a single lock-class, causing "possible recursive locking detected" when the TWL RTC driver calls through enable_irq_wake to twl6030_irq_set_wake, which recursively calls irq_set_irq_wake. Although the irq_desc and lock are different, LOCKDEP treats these as equivalent, presumably due to problems that can be incurred when locking more than one irq_desc, so best to avoid this. Suspend/resume actions implemented as PM notifiers to avoid touch the TWL core for this. Signed-off-by: Todd Poynor <toddpoynor@google.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Fix a sparse warning about mc13xxx_chipname not being declaredUwe Kleine-König2011-10-241-1/+1
| | | | | | | | | | Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Delete ab3550 driverLinus Walleij2011-10-243-1395/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | The AB3550 never passed the prototype stage. Instead it was used as a precursor to AB5500 for testing basic building blocks used in that chip, since they had large similarities. Since AB3550 will not see the light of day in product form and since the prototypes are no longer used, let's delete the driver and any references to it. Cc: Mattias Wallin <mattias.wallin@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Break out ab5500 debugfs codeLinus Walleij2011-10-246-890/+941
| | | | | | | | | | | | | | | | | | | | | | This breaks the debugfs portions of the AB5500 driver into its own file. Split off a _raw function to access registers since we don't want to expose a generically named function globally. Move all required data structures to a shared ab5500-core.h file. Cc: Mattias Wallin <mattias.wallin@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: ab5500 chip register accessMattias Wallin2011-10-243-0/+2322
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The analog baseband chip ab5500 is a multi functional chip containing regulators, charging, gpio, USB and accessory detect. It also contain various multimedia functionalities like digital encoder and audio codec. The core driver added with this patch provides register access via i2c via PRCMU. Event handling implemented as irq_chip will come in future patches since it depends on PRCMU functionality not yet implemented. Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Do not leak init_data in tps65912_device_init()Jesper Juhl2011-10-241-3/+3
| | | | | | | | | | | | | | | | | | | | | | We neglect to free init_data on successful exit. I also moved two assignments to just before they are needed. This avoids doing them in case we hit an earlier error exit from the function. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Cc: Margarita Olaya Cabrera <magi@slimlogic.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Fix ab3100 initconst sectionAndi Kleen2011-10-241-1/+1
| | | | | | | | | | Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Add Intel MSIC driverMika Westerberg2011-10-243-0/+511
| | | | | | | | | | | | | | | | | | | | | | | | | | Add support for Intel MSIC chip found on Intel Medfield platforms. This chip embeds several subdevices: audio, ADC, GPIO, power button, etc. The driver creates platform device for each subdevice. We also provide an MSIC register access API which should replace the more generic SCU IPC interface currently used. Existing drivers can choose whether they convert to this new API or stick with the SCU IPC interface. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Make jz4740_adc_driver staticLars-Peter Clausen2011-10-241-1/+1
| | | | | | | | | | Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * mfd: Simulate active high IRQs with wm831xMark Brown2011-10-241-1/+21
| | | | | | | | | | | | | | | | | | | | | | In order to ease system integration provide a simulation of active high IRQs on the GPIOs by polling the GPIO status when an IRQ is generated. This isn't ideal on several fronts and will miss initially active IRQs in the current implementation but it should work well for most cases. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
generated by cgit v1.1 at 2025-01-28 06:02:16 +0000