diff options
Diffstat (limited to 'drivers/net/qlge')
| -rw-r--r-- | drivers/net/qlge/qlge_ethtool.c | 38 | ||||
| -rw-r--r-- | drivers/net/qlge/qlge_main.c | 10 |
2 files changed, 24 insertions, 24 deletions
diff --git a/drivers/net/qlge/qlge_ethtool.c b/drivers/net/qlge/qlge_ethtool.c index 8149cc9..687754d 100644 --- a/drivers/net/qlge/qlge_ethtool.c +++ b/drivers/net/qlge/qlge_ethtool.c @@ -412,31 +412,31 @@ static int ql_set_wol(struct net_device *ndev, struct ethtool_wolinfo *wol) return 0; } -static int ql_phys_id(struct net_device *ndev, u32 data) +static int ql_set_phys_id(struct net_device *ndev, + enum ethtool_phys_id_state state) + { struct ql_adapter *qdev = netdev_priv(ndev); - u32 led_reg, i; - int status; - /* Save the current LED settings */ - status = ql_mb_get_led_cfg(qdev); - if (status) - return status; - led_reg = qdev->led_config; + switch (state) { + case ETHTOOL_ID_ACTIVE: + /* Save the current LED settings */ + if (ql_mb_get_led_cfg(qdev)) + return -EIO; - /* Start blinking the led */ - if (!data || data > 300) - data = 300; - - for (i = 0; i < (data * 10); i++) + /* Start blinking */ ql_mb_set_led_cfg(qdev, QL_LED_BLINK); + return 0; - /* Restore LED settings */ - status = ql_mb_set_led_cfg(qdev, led_reg); - if (status) - return status; + case ETHTOOL_ID_INACTIVE: + /* Restore LED settings */ + if (ql_mb_set_led_cfg(qdev, qdev->led_config)) + return -EIO; + return 0; - return 0; + default: + return -EINVAL; + } } static int ql_start_loopback(struct ql_adapter *qdev) @@ -703,7 +703,7 @@ const struct ethtool_ops qlge_ethtool_ops = { .get_msglevel = ql_get_msglevel, .set_msglevel = ql_set_msglevel, .get_link = ethtool_op_get_link, - .phys_id = ql_phys_id, + .set_phys_id = ql_set_phys_id, .self_test = ql_self_test, .get_pauseparam = ql_get_pauseparam, .set_pauseparam = ql_set_pauseparam, diff --git a/drivers/net/qlge/qlge_main.c b/drivers/net/qlge/qlge_main.c index 49bfa58..5bb3119 100644 --- a/drivers/net/qlge/qlge_main.c +++ b/drivers/net/qlge/qlge_main.c @@ -660,7 +660,7 @@ static void ql_disable_interrupts(struct ql_adapter *qdev) /* If we're running with multiple MSI-X vectors then we enable on the fly. * Otherwise, we may have multiple outstanding workers and don't want to * enable until the last one finishes. In this case, the irq_cnt gets - * incremented everytime we queue a worker and decremented everytime + * incremented every time we queue a worker and decremented every time * a worker finishes. Once it hits zero we enable the interrupt. */ u32 ql_enable_completion_interrupt(struct ql_adapter *qdev, u32 intr) @@ -3299,7 +3299,7 @@ msi: * will service it. An example would be if there are * 2 vectors (so 2 RSS rings) and 8 TX completion rings. * This would mean that vector 0 would service RSS ring 0 - * and TX competion rings 0,1,2 and 3. Vector 1 would + * and TX completion rings 0,1,2 and 3. Vector 1 would * service RSS ring 1 and TX completion rings 4,5,6 and 7. */ static void ql_set_tx_vect(struct ql_adapter *qdev) @@ -4152,7 +4152,7 @@ static int ql_change_rx_buffers(struct ql_adapter *qdev) int i, status; u32 lbq_buf_len; - /* Wait for an oustanding reset to complete. */ + /* Wait for an outstanding reset to complete. */ if (!test_bit(QL_ADAPTER_UP, &qdev->flags)) { int i = 3; while (i-- && !test_bit(QL_ADAPTER_UP, &qdev->flags)) { @@ -4281,7 +4281,7 @@ static void qlge_set_multicast_list(struct net_device *ndev) if (ql_set_routing_reg (qdev, RT_IDX_PROMISCUOUS_SLOT, RT_IDX_VALID, 1)) { netif_err(qdev, hw, qdev->ndev, - "Failed to set promiscous mode.\n"); + "Failed to set promiscuous mode.\n"); } else { set_bit(QL_PROMISCUOUS, &qdev->flags); } @@ -4291,7 +4291,7 @@ static void qlge_set_multicast_list(struct net_device *ndev) if (ql_set_routing_reg (qdev, RT_IDX_PROMISCUOUS_SLOT, RT_IDX_VALID, 0)) { netif_err(qdev, hw, qdev->ndev, - "Failed to clear promiscous mode.\n"); + "Failed to clear promiscuous mode.\n"); } else { clear_bit(QL_PROMISCUOUS, &qdev->flags); } |