aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* wl1251: mask aid bits 14 and 15 in ps-poll templateKalle Valo2009-11-181-1/+4
| | | | | | | | | | In ps-poll template aid bits 14 and 15 were not masked as required by the standard. Mask them so that aid is sent in correct format. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: allocate space for firmware with vmalloc()Kalle Valo2009-11-182-7/+25
| | | | | | | | | | | | | | Earlier firmware was stored to a memory area allocated with kmalloc() but finding a a contiguous area of memory long enough for the firmware is very difficult in certain cases. better to allocate the memory for firmware with vmalloc() instead and use a small buffer for DMA transfers. Thanks to Eero Tamminen for the idea. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: Implement delayed entry into ELP modeJuuso Oikarinen2009-11-184-5/+33
| | | | | | | | | | | | | | | Implement (slightly) delayed entry into ELP. This will cure several problems: - It works around a firmware race condition if ELP is entered too fast after commands (resulting in ELP timeout -traces) - It will reduce the number of sleep-wake cycles between already scheduled events such as interrupts and tx, hence improving performance (less delay in switching between RX and TX) Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: Configure beacon filtering on if PSM usedJuuso Oikarinen2009-11-185-7/+27
| | | | | | | | Enable beacon filtering when PSM is enabled Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: Enable beacon filtering with the stackJuuso Oikarinen2009-11-183-0/+21
| | | | | | | | Enable beacon filtering with the mac80211 stack. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: Add connection monitoring configurationJuuso Oikarinen2009-11-183-0/+45
| | | | | | | | | Add configuration for connection monitor (number of allowed beacons, and timeout after last received beacon.) Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ar9170: Add support for D-Link DWA 160 A2Thomas Klute2009-11-181-1/+3
| | | | | | | | | | | | | | | | At least two revisions of the D-Link DWA 160 exist, called A1 and A2. A1 (USB-ID 07d1:3c10) is already listed in usb.c as D-Link DWA 160A. A2 (USB-ID 07d1:3a09) works if added to ar9170_usb_ids. I didn't do much testing until now, but I was able to connect to APs using WPA or WEP and transmit data. Summary: * Add model revision number to the comment for D-Link DWA 160 A1 (07d1:3c10) * Add support for D-Link DWA 160 A2 (07d1:3a09) Signed-off-by: Thomas Klute <thomas2.klute@uni-dortmund.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: more ids to rt2800usb.cXose Vazquez Perez2009-11-181-2/+37
| | | | | | | | taken from windows inf file (09/15/2009, 1.04.07.0000) Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: use fixed broadcast addressJohannes Berg2009-11-186-19/+27
| | | | | | | | | | | | | | | | | The netdev broadcast address cannot change from all-ones so there's no need to use it; we can instead hard-code it. Since we already have an instance in tkip.c, which will be shared if it is marked static const, doing this reduces text size at no data/bss cost. The real motivation for this is, of course, the desire to get rid of almost all uses of netdevs in mac80211 so that auditing their use becomes easier. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: remove dev_hold/put callsJohannes Berg2009-11-181-11/+5
| | | | | | | | If we move the rcu sections a little, there's no need to touch the device refcount. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: improve rate handlingJohannes Berg2009-11-182-18/+18
| | | | | | | | | | | | | | | | Some code currently assumes that there's a valid rate pointer even in the HT case, but there can't be. To reduce reliance on that, remove the rate pointer from the RX data struct and pass it where it's needed. Also, for now, in radiotap announce HT frames as having a DYN channel type, and remove their rate from cooked monitor radiotap completely (it isn't present in the regular monitor radiotap either.) Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: trim RX dataJohannes Berg2009-11-184-54/+61
| | | | | | | | | | | | The RX data contains the netdev, which is duplicated since we have the sdata, and the RX status pointer, which is duplicate since we have the skb. Remove those two fields to have fewer fields that depend on each other and simply load them as necessary. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: cleanup reorder buffer handlingJohannes Berg2009-11-181-81/+81
| | | | | | | | | | | | | | | | | The reorder buffer handling is written in a quite peculiar style (especially comments) and also has a quirk where it invokes the entire reorder code in ieee80211_sta_manage_reorder_buf() for just a handful of lines in it with a special argument. Split out ieee80211_release_reorder_frames which can then be invoked from BAR handling and other reordering code, clean up code and comments and remove function arguments that are now unused from ieee80211_sta_manage_reorder_buf(). Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: push michael MIC report after DA checkJohannes Berg2009-11-181-24/+23
| | | | | | | | | | | | | | | | When we receive a michael MIC failure report from the hardware we currently do not check whether it is actually reported on a frame that is destined to us. It shouldn't be possible to get a michael MIC failure report on other frames, but it also doesn't hurt to verify. Also, since we then don't need the station struct that early, move looking it up a bit later in the RX path. Finally, while at it, a few code cleanups in the area. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: convert aggregation to operate on vifs/stasJohannes Berg2009-11-1814-97/+84
| | | | | | | | | | | | The entire aggregation code currently operates on the hw pointer and station addresses, but that needs to change to make stations purely per-vif; As one step preparing for that make the aggregation code callable with the station, or by the combination of virtual interface and station address. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: let sta_info_get_by_idx get sta by sdataJohannes Berg2009-11-183-7/+8
| | | | | | | Instead of filtering by device, directly look up by sdata. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Fix bug in initializing chain masksSujith2009-11-181-1/+1
| | | | | | | | | Check for AR5416 ver 1.0 before calibrating 3 chains for multi-chain. This is a WAR for calibration failure. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Remove a few unused functionsSujith2009-11-184-169/+0
| | | | | | | | | | | ATH9K_ANT_VARIABLE is the default diversity control used. Consequently ath9k_hw_decrease_chain_power() does nothing. ath9k_hw_setantennaswitch() is unused too. Also, gbeacon_rate is unused. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Remove a few unused variablesSujith2009-11-182-23/+0
| | | | | | | | axq_linkbuf, axq_aggr_depth, axq_lastdsWithCTS and axq_gatingds are unused. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Cleanup bss_info_changed callbackSujith2009-11-181-77/+37
| | | | | | | | | | | | | | | | | | | | | | | | * Remove a code chunk dealing with operating mode changes. As noted, all such policy changes are to be done in add_interface. * Remove pointless check for empty BSSID. Also, remove mode checks - mac80211 does all the needed checks. * Handle enabling/disabling beacon transmission properly. * Handle beacon interval changes for AP mode. The original code depended on config_interface() to update the HW TSF. Since that callback has been removed, handle it properly. * Remove unneeded code dealing with key/privacy. * Set the chainmasks to 1x1 for IBSS when the BSSID is set. This was happening uncondionally before. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: get rid of tx_info_privFelix Fietkau2009-11-186-97/+83
| | | | | | | | | This patch removes the need for separately allocated private tx info data in ath9k and brings the driver one small step closer to using the mac80211 rate control API properly. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: add the total ampdu length to tx infoFelix Fietkau2009-11-181-2/+5
| | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: reduce the amount of unnecessary traffic on cooked monitor interfacesFelix Fietkau2009-11-181-0/+5
| | | | | | | | | | | | | | | | | | In order to handle association and authentication in AP mode, hostapd needs access to the tx status info of its own frames through a cooked monitor interface. Without this patch the cooked monitor interfaces also passed on tx status information for packets from other virtual interfaces. This creates a significant performance issue on embedded system. Hostapd tries to work around this by installing a Linux Socket Filter that only captures the frames it's interested in, however data duplication and socket filter matching still uses up enough CPU cycles to be very noticeable on small systems. This patch ensures that tx status information of non-injected frames does not make it to cooked monitor interfaces. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ar9170: do not discard valuable DUPOFDM framesChristian Lamparter2009-11-181-2/+2
| | | | | | | | This patch enables the driver to process all incoming dupofdm-modulated frames when operating in HT40 mode. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: Add comments about CSR registersBen Cahill2009-11-181-27/+150
| | | | | | | | Also regroup CSR_EEPROM and CSR_OTP bit field definitions. Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: handle unicast PS bufferingJohannes Berg2009-11-188-42/+113
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Using the new mac80211 functionality, this makes iwlwifi handle unicast PS buffering correctly. The device works like this: * when a station goes to sleep, the microcode notices this and marks the station as asleep * when the station is marked asleep, the microcode refuses to transmit to the station and rejects all frames queued to it with the failure status code TX_STATUS_FAIL_DEST_PS (a previous patch handled this correctly) * when we need to send frames to the station _although_ it is asleep, we need to tell the ucode how many, and this is asynchronous with sending so we cannot just send the frames, we need to wait for all other frames to be flushed, and then update the counter before sending out the poll response frames. This is handled partially in the driver and partially in mac80211. In order to do all this correctly, we need to * keep track of how many frames are pending for each associated client station (avoid doing it for other stations to avoid the atomic ops) * tell mac80211 that we driver-block the PS status while there are still frames pending on the queues, and once they are all rejected (due to the dest sta being in PS) unblock mac80211 Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: add sleep_tx_count ucode station APIJohannes Berg2009-11-182-2/+17
| | | | | | | | | | This field was marked as reserved before since we didn't use it, but is present in all released firmwares afaict. We're going to need it soon, so add it now. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: report PS filtered statusJohannes Berg2009-11-183-8/+19
| | | | | | | | | | | When a frame is sent to a sleeping station, the microcode reports TX_STATUS_FAIL_DEST_PS as its status -- we need to translate that to the flag that mac80211 expects. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: make iwlwifi send beaconsDaniel C Halperin2009-11-182-0/+13
| | | | | | | | | | Handle BSS_CHANGED_BEACON_ENABLED to enable the sending of beacons. Also set the correct HT RXON and QoS config. Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: fix bugs in beacon configurationDaniel C Halperin2009-11-182-21/+63
| | | | | | | | | | | | | | | | | | | | When sending beacon commands to the uCode, we must inform it of the offset in the beacon frame of the TIM Element so it can transmit packets from the correct queue. This functionality is implemented in iwl_set_beacon_tim(). Fix a bug setting the rate_n_flags for the beacon packet. First, it should not use the station table's rate (it's a management frame), and second it needs to properly configure the TX antennas. Finally, also, clean up and comment relevant functions. Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlagn: power up device before initializing EEPROMReinette Chatre2009-11-181-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A recent change optimized the power usage by the device by only powering it up during EEPROM load if it is required (for OTP devices). This change causes an error on the 1000 series devices during module load. The error looks as follows: [ 1624.024524] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds [ 1624.024527] iwlagn: Copyright(c) 2003-2009 Intel Corporation [ 1624.024711] iwlagn 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1624.024749] iwlagn 0000:01:00.0: setting latency timer to 64 [ 1624.024909] iwlagn 0000:01:00.0: Detected Intel Wireless WiFi Link 1000 Series BGN REV=0x6C [ 1624.081263] iwlagn 0000:01:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080003D8 [ 1624.092967] iwlagn 0000:01:00.0: OTP is empty [ 1624.092988] iwlagn 0000:01:00.0: Unable to init EEPROM [ 1624.093033] iwlagn 0000:01:00.0: PCI INT A disabled [ 1624.093065] iwlagn: probe of 0000:01:00.0 failed with error -2 Adding a dump_stack() to where that error is printed shows the following: [ 1624.024524] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds [ 1624.024527] iwlagn: Copyright(c) 2003-2009 Intel Corporation [ 1624.024711] iwlagn 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1624.024749] iwlagn 0000:01:00.0: setting latency timer to 64 [ 1624.024909] iwlagn 0000:01:00.0: Detected Intel Wireless WiFi Link 1000 Series BGN REV=0x6C [ 1624.081263] iwlagn 0000:01:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080003D8 [ 1624.081263] Pid: 3073, comm: work_for_cpu Tainted: G W 2.6.31.5 #4 [ 1624.081263] Call Trace: [ 1624.081263] [<ffffffffa02395db>] T.726+0x22b/0x420 [iwlcore] [ 1624.081263] [<ffffffffa023985a>] iwlcore_eeprom_acquire_semaphore+0x8a/0x190 [iwlcore] [ 1624.081263] [<ffffffff81110c94>] ? __kmalloc+0x194/0x1c0 [ 1624.081263] [<ffffffffa02391f5>] ? iwlcore_eeprom_verify_signature+0x25/0xf0 [iwlcore] [ 1624.081263] [<ffffffffa0239c67>] iwl_eeprom_init+0x107/0xf40 [iwlcore] [ 1624.081263] [<ffffffffa026ab9c>] ? iwl_prepare_card_hw+0x11c/0x470 [iwlagn] [ 1624.081263] [<ffffffff8127e2a4>] ? pci_bus_write_config_byte+0x64/0x80 [ 1624.081263] [<ffffffffa026b1f8>] iwl_pci_probe+0x308/0xac0 [iwlagn] [ 1624.081263] [<ffffffff810710a0>] ? do_work_for_cpu+0x0/0x30 [ 1624.081263] [<ffffffff81284912>] local_pci_probe+0x12/0x20 [ 1624.081263] [<ffffffff810710b3>] do_work_for_cpu+0x13/0x30 [ 1624.081263] [<ffffffff81075826>] kthread+0xa6/0xb0 [ 1624.081263] [<ffffffff81012fea>] child_rip+0xa/0x20 [ 1624.081263] [<ffffffff81075780>] ? kthread+0x0/0xb0 [ 1624.081263] [<ffffffff81012fe0>] ? child_rip+0x0/0x20 [ 1624.092967] iwlagn 0000:01:00.0: OTP is empty [ 1624.092988] iwlagn 0000:01:00.0: Unable to init EEPROM [ 1624.093033] iwlagn 0000:01:00.0: PCI INT A disabled [ 1624.093065] iwlagn: probe of 0000:01:00.0 failed with error -2 We know that the routines in this trace, iwlcore_eeprom_acquire_semaphore and iwlcore_eeprom_verify_signature, only access CSR registers and thus do not need the device to be awake if it is EEPROM. But for OTP it is required for the device to be awake to read these registers. Ensure device is awake before accessing these registers. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Acked-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: align tx/rx statistics debugfs formatWey-Yi Guy2009-11-181-6/+7
| | | | | | | | | Align the format for tx_statistics and rx_statistics debugfs output for better readability Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: eliminate the possible 1/2 dBm tx power loss in 6x00 & 6x50 seriesWey-Yi Guy2009-11-183-14/+52
| | | | | | | | | | | | | | | | In both 6x00 and 6x50 series, the enhanced/extended tx power table in EEPROM is used to set the max. tx power limit. This new tx power table is in 1/2 dBm format, which creates an issue of possibility of 1/2 dBm loss when driver set the tx power limit; because of driver keep track and report the tx power in dBm format. In order to prevent the 1/2 dBm loss, keep track of the true max tx power in 1/2 dBm format in driver; do the comparison and adjust the tx power if needed when send tx power command to uCode. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwl3945: Reset saved POWER_TABLE_CMD in "up"Ben Cahill2009-11-181-1/+1
| | | | | | | | | | | | | Power-saving logic will not re-issue a POWER_TABLE_CMD if a new command matches the prior one. This can be bad if we re-start the device due to e.g. uCode error; the new POWER_TABLE_CMD (required to invoke power-saving) may match the prior POWER_TABLE_CMD issued before the uCode error. Ensure the POWER_TABLE_CMD is sent to device when uCode is up. Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: update reply_statistics_cmd with 'clear' parameterWey-Yi Guy2009-11-1810-23/+77
| | | | | | | | | | | | | | | | | | When issue REPLY_STATISTICS_CMD to uCode, two possible flag can be set in the configuration flags bit 0: Clear statistics 0: Do not clear Statistics counters 1: Clear to zero Statistics counters Allow "clear" parameter to be set from the caller. Add debugfs file to clear the statistics counters to help monitor and debug the uCode behavior. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: remove external reference for non-exist data structureWey-Yi Guy2009-11-181-3/+0
| | | | | | | | | | Number of data structure for 6000 series no longer in production, the data structure already being removed; also need to remove the external reference define in iwl-dev.h Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: drop non-production PCI-IDs for 6x50 seriesWey-Yi Guy2009-11-183-36/+0
| | | | | | | | drop the non-production PCI-IDs for 6x50 series Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: remove unused parameter from iwl_channel_infoWey-Yi Guy2009-11-182-10/+0
| | | | | | | | | Number of HT40 power parameters are not used; remove those from iwl_channel_info data structure Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: disable coex until implementation ready for 6x50Wey-Yi Guy2009-11-181-2/+0
| | | | | | | | | Temporary disable the coex function for wifi/wimax for 6x50 series until the full implementation ready. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: validate enhanced tx power entryWey-Yi Guy2009-11-182-2/+14
| | | | | | | | | | | Validate enhanced tx power entry read from EEPROM before applying the tx power value. Different versions of EEPROM might contain different size of table; always a good idea to make sure the entry is valid before applying to the targeted channel. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Merge branch 'master' of ↵David S. Miller2009-11-18121-2220/+2687
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
| * znet: fix build failure from i82593.h relocationJohn W. Linville2009-11-173-3/+2
| | | | | | | | | | | | | | | | | | znet was including "wireless/i82593.h" (which is a bit wierd), and I missed that when I relocated i82593.h to drivers/staging/wavelan. Since I don't have ISA turned-on in my normal .config, I didn't see the build failures -- mea culpa! Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * mac80211: Do not queue Probe Request frames for station MLMEJouni Malinen2009-11-161-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | Cooked monitor interfaces cannot currently receive Probe Request frames when the interface is in station mode. However, we do not process Probe Request frames internally in the station MLME, so there is no point in queueing the frame here. Remove Probe Request frames from the queued frame list to allow cooked monitor interfaces to receive these frames. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath5k: allow setting txpower to 0Bob Copeland2009-11-161-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As a holdover from earlier code when we used to set the power limit to '0' after a reset to configure the default transmit power, ath5k interprets txpower=0 as 12.5 dBm. Fix that by just passing 0 through. This fixes http://bugzilla.kernel.org/show_bug.cgi?id=14567 Cc: stable@kernel.org Reported-by: Daniel Folkers <daniel.folkers@task24.nl> Tested-by: Daniel Folkers <daniel.folkers@task24.nl> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * rndis_wlan: handle NL80211_AUTHTYPE_AUTOMATICJussi Kivilinna2009-11-161-0/+2
| | | | | | | | | | | | | | | | | | | | | | rndis_wlan didn't know about NL80211_AUTHTYPE_AUTOMATIC and simple setup with 'iwconfig wlan essid no-encrypt' would fail (ENOSUPP). v2: use NDIS_80211_AUTH_AUTO_SWITCH instead of _OPEN. This will make device try shared key auth first, then open. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * rt2800: do not enable tbtt unless we are in a beacon modeJosef Bacik2009-11-161-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Please be gentle, I'm a fs developer and this is my first foray into drivers, as I'm tired of building ralinks driver everytime I update my kernel. Whenever I load the rt2800pci driver my box bogs down, and a few printk's later I discovered its because I was getting 10's of thousands of TBTT interrupts a second. I discovered this was because we were setting the beacon timer to 0, which is apparently what TBTT keys off of. It seems to me that we should only be enabling TBTT when we are in a beacon transmitting mode, which from what I can tell is in AD-HOC and other such modes where the mac80211 layer would have given us a proper beacon_int to set the beacon timer to instead of 0. So this is my fix, only enable TBTT if our sync mode is for beacon. This makes it so my box doesn't die everytime I load the rt2800pci driver. Let me know if this is acceptable, I just learned all these terms about 15 minutes ago via wikipedia, so I really am not familiar with how this stuff is supposed to work. Thanks, Signed-off-by: Josef Bacik <josef@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath9k: fix massive rx packet loss issueFelix Fietkau2009-11-161-0/+1
| | | | | | | | | | | | | | | | | | | | This patch fixes a regression introduced in "ath9k: avoid the copy skb->cb on every RX'd skb" With that change, the rx status in skb->cb was left uninitialized Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * rt2x00: Fix BUG on rt2800usb when trying to read eFuse EEPROM.Gertjan van Wingerde2009-11-164-10/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current tree hits a BUG_ON in rt2x00_regbusy_read, because the eFuse EEPROM reading code of rt2800lib uses the function without the csr_mutex locked. Fix this by locking the csr_mutex for the of the EEPROM reading cycly and using the _lock variants of the register reading and writing functions. This also introcudes the register_read_lock function pointer in the rt2800_ops structure. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * rt2x00: Log RT/RF chipset information correctly.Gertjan van Wingerde2009-11-167-4/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | Some drivers (rt2800* most notably) cannot set the RF and RT chipset in the correct order to have the information logging in rt2x00_set_chip be correct. Fix this by decoupling the setting of the chipset information from the logging of the chipset information so that drivers can determine themselves when all information is set. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * rt2x00: Initialize rf302x RF values properly for rt2800pci.Gertjan van Wingerde2009-11-161-17/+12
| | | | | | | | | | | | | | | | | | Ensure RF302x and RF2020 chipsets are handled properly in rt2800lib for the rt3090 chipset. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.1 at 2025-01-30 01:29:25 +0000