aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ssb: Add PMU supportMichael Buesch2009-02-094-13/+734
| | | | | | | | This adds support for the SSB PMU. A PMU is found on Low-Power devices. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* libertas: pos[4] tested twice, 2nd should be pos[5]Roel Kluin2009-02-091-1/+1
| | | | | | | | pos[4] can't be both 0x43 and 0x04, 2nd should be pos[5] Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* libertas: if_spi: add ability to call board specific setup/teardown methodsMike Rapoport2009-02-092-0/+22
| | | | | | | | | | | | | In certain cases it is required to perform board specific actions before activating libertas G-SPI interface. These actions may include power up of the chip, GPIOs setup, proper pin-strapping and SPI controller config. This patch adds ability to call board specific setup/teardown methods Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Andrey Yurovsky <andrey@cozybit.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: Remove bss information of the current AP when it goes out of rangeVasanthakumar Thiagarajan2009-02-091-2/+16
| | | | | | | | There is no point having the bss information of currently associated AP when the AP is detected to be out of range. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: fix reg_notifier() flags used upon a country IELuis R. Rodriguez2009-02-091-2/+2
| | | | | | | The nl80211 rule flags were being used. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Add LP 2062 radio initMichael Buesch2009-02-094-4/+355
| | | | | | | This adds initialization code for the 2062 radio. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Add LP-PHY baseband init for >=rev2Michael Buesch2009-02-095-3/+228
| | | | | | | This adds code for the baseband init of LP-PHY >=2. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: another led naming fixDanny Kukawka2009-02-091-4/+4
| | | | | | | | | | | | | Fixed led device naming for the iwlwifi (iwl-3945) driver. Due to the documentation of the led subsystem/class the naming should be "devicename:colour:function" while not applying sections should be left blank. This should lead to e.g. "iwl-%s::RX" instead of "iwl-%s:RX". Signed-off-by: Danny Kukawka <dkukawka@suse.de> Acked-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: fix led namingDanny Kukawka2009-02-091-3/+3
| | | | | | | | | | | | Fixed led device naming for the rt2x00 driver. Due to the documentation of the led subsystem/class the naming should be "devicename:colour:function" while not applying sections should be left blank. This should lead to e.g. "%s::radio" instead of "%s:radio". Signed-off-by: Danny Kukawka <dkukawka@suse.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43legacy: fix led namingDanny Kukawka2009-02-091-4/+4
| | | | | | | | | | | | | | Fixed led device naming for the b43legacy driver. Due to the documentation of the led subsystem/class the naming should be "devicename:colour:function" while not applying sections should be left blank. This should lead to e.g. "b43legacy-%s::rx" instead of "b43legacy-%s:rx". Signed-off-by: Danny Kukawka <dkukawka@suse.de> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: fix led namingDanny Kukawka2009-02-091-5/+5
| | | | | | | | | | | | Fixed led device naming for the ath9k driver. Due to the documentation of the led subsystem/class the naming should be "devicename:colour:function" while not applying sections should be left blank. This should lead to e.g. "ath9k-%s::rx" instead of "ath9k-%s:rx". Signed-off-by: Danny Kukawka <dkukawka@suse.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Add LP-PHY register definitionsMichael Buesch2009-02-092-0/+306
| | | | | | | | This adds register definitions for the LP-PHY. This also adds a few minor empty function bodies for the LP-init. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add new rt73usb USB IDIvo van Doorn2009-02-091-0/+1
| | | | | Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: add get reg commandLuis R. Rodriguez2009-02-094-1/+88
| | | | | | | | This lets userspace request to get the currently set regulatory domain. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: do not TX injected frames when not allowedLuis R. Rodriguez2009-02-091-0/+21
| | | | | | | | | | | | | | | | | | Monitor mode is able to TX by using injected frames. We should not allow injected frames to be sent unless allowed by regulatory rules. Since AP mode uses a monitor interfaces to transmit management frames we have to take care to not break AP mode as well while resolving this. We can deal with this by allowing compliant APs solutions to inform mac80211 if their monitor interface is intended to be used for an AP by setting a cfg80211 flag for the monitor interface. hostapd, for example, currently does its own checks to ensure AP mode is not used on channels which require radar detection. Once such solutions are available it can can add this flag for monitor interfaces. Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: convert master interface to netdev_opsJohannes Berg2009-02-091-10/+18
| | | | | | | | | | Also call our own ieee80211_master_setup routine instead of overwriting almost all the values from ether_setup; this loses a few assignments that are pointless on the master interface anyway. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: convert to net_device_opsJohannes Berg2009-02-091-17/+30
| | | | | | | | Convert to new net_device_ops in 2.6.28 and later. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: remove HW_SIGNAL_DBJohannes Berg2009-02-095-28/+11
| | | | | | | | | | | | | Giving the signal in dB isn't much more useful to userspace than giving the signal in unspecified units. This removes some radiotap information for zd1211 (the only driver using this flag), but it helps a lot for getting cfg80211-based scanning which won't support dB, and zd1211 being dB is a little fishy anyway. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Bruno Randolf <bruno@thinktube.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Add debugfs files for printing TX rate detailsSujith2009-02-093-0/+119
| | | | | Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Handle mac80211's RC flags for MCS ratesSujith2009-02-094-117/+111
| | | | | | | | | | | mac80211 notifies the RC algorithm if RTS/CTS and short preamble are needed. The RC flags for MCS rates are currently not handled by mac80211, and ath9k's RC doesn't set the flags either. Fix this. Also, set the rts_cts_rate_idx inside the RC algorithm. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Cleanup get_rate() interfaceSujith2009-02-091-39/+28
| | | | | | | | | The interface to calculate the TX rate for a data frame was convoluted with lots of redundant arguments being passed around. Remove all of that and make it simple. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath5k: properly free rx dma descriptorsFelix Fietkau2009-02-091-1/+14
| | | | | | | | | | When freeing rx dma descriptors, use the right buffer size. Fixes kernel oopses on module unload on ixp4xx and most likely other platforms as well. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wireless: replace uses of __constant_{endian}Harvey Harrison2009-02-0915-36/+36
| | | | | | | The base versions handle constant folding now. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: fix led namingDanny Kukawka2009-02-091-4/+4
| | | | | | | | | | | | | Fixed led device naming for the iwl driver. Due to the documentation of the led subsystem/class the naming should be "devicename:colour:function" while not applying sections should be left blank. This should lead to e.g. "iwl-phy0::RX" instead of "iwl-phy0:RX". Signed-off-by: Danny Kukawka <dkukawka@suse.de> Acked-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ipw2x00: correct Kconfig to prevent following entries from not indentingJay Sternberg2009-02-091-0/+1
| | | | | | | | | | not defining dependencies for LIBIPW caused the following entries to not be indented. changing this entry to depend on PCI && WLAN_80211 corrects this issue Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: remove chain noise calibration functions from 6000 familyJay Sternberg2009-02-092-7/+21
| | | | | | | | | redefine structures that contain function pointer for chain noise reset and chain noise gain for the 6000 family since these are not needed. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: define structures and functions externally for customizationJay Sternberg2009-02-092-7/+19
| | | | | | | | | defined the structures and functions as extern to alter behavior used by 5000 series for other products including 100 and 6000 series Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: correct API command overlapJay Sternberg2009-02-094-5/+14
| | | | | | | | | | | | | | Correct the API commands where same command id used for two different commands. Update max api versions for affected devices. TX_ANT_CONFIGURATION_CMD was already using id 0x98, so REPLY_TX_POWER_DBM_CMD moved to 0x95 Older API interfaces may used original value so V1 defines provided. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: parametrize configuration of the PLL for exclusion on 6000Jay Sternberg2009-02-094-2/+17
| | | | | | | | | | added a config parameter to enable setting PLL_CFG. older hardware has this parameter set true. the 6000 family does not support this setting, so this parameter set false. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: simplify parameter setting to allow support for 6000 seriesJay Sternberg2009-02-094-37/+53
| | | | | | | | | | by parametrizing the set hw function, in addition to allowing for supporting the 6000 family significantly simplify the addition of new hardware. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: add new HW_REV_TYPEs for Intel WiFi Link 100, 6000 and 6050 SeriesJay Sternberg2009-02-091-0/+3
| | | | | | | | simply add definitions for the HW_REV_TYPEs for the new devices. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: IBSS join reworkAlina Friedrichsen2009-02-091-7/+14
| | | | | | | | | | | | | | | | | I hold back this patch for around a week to avoid confusion. This is the second step of "mac80211: Fixed BSSID handling revisited". With it, in the situation of a strange merge to the same BSSID (e.g. caused by a TSF overflow) only reset_tsf() is called. And sta_info_flush_delayed() is only called if you change the network manually, not on an automatic BSSID merge. Signed-off-by: Alina Friedrichsen <x-alina@gmx.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Fix LED blink patternVasanthakumar Thiagarajan2009-02-092-6/+56
| | | | | Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: Creating new IBSS with fixed BSSIDAlina Friedrichsen2009-02-091-3/+2
| | | | | | | | | | | | | | | | This fixes a bug when creating a new IBSS network with a fixed BSSID. The fixed BSSID situation is now with one of my last patches handled in ieee80211_sta_find_ibss() function. It's more robust to test against (ifsta->flags & IEEE80211_STA_PREV_BSSID_SET), because ifsta->state is not seted right in every situation and so the creating of the new IBSS network sometimes hangs after the first try to scan for a network to merge. Signed-off-by: Alina Friedrichsen <x-alina@gmx.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Remove a bunch of unused macrosSujith2009-02-091-11/+0
| | | | | | | | RX filter masks are already defined in enum ath9k_rx_filter in ath9k.h Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Fix typo in checking for chip revisionSujith2009-02-091-1/+1
| | | | | Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: Reset assoc_scan_tries after an unsuccessful scan runSujith2009-02-091-1/+3
| | | | | | | | | | Trying to associate with a non-existent SSID stops the state machine after the first run. Subsequent association requests fail to start the scan engine. Fix this by resetting assoc_scan_tries to zero after completing a scan run. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: remove passive scan on 5 GHz if country IE knows betterLuis R. Rodriguez2009-02-091-4/+12
| | | | | | | | | | | | | | | If we have new found information about our location and the current country regulatory domain does not have passive scan flag requirements we should be able to actively scan now on those channels. Since AP functionality is not allowed where passive scan flags are set this means if you have a world regulatory domain and you get a country IE that allows that channel (with active scan) then we lift the passive-scan requirement so you can then use AP mode. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: move check for radar freqs into a helperLuis R. Rodriguez2009-02-091-3/+7
| | | | | | | This will be used later. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: replace usage of internal wireless_modes for confLuis R. Rodriguez2009-02-091-4/+1
| | | | | | | | No need to use our internal wireless mode variable when cfg80211 already has its own. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Enable MIB and TIM interrupts for station mode.Vivek Natarajan2009-02-091-19/+21
| | | | | | | | Enable operating mode specific interrupts in ath9k_add_interface instead of ath9k_start. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Fix lockdep warningSujith2009-02-092-16/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes the lockdep warning shown below, and also initializes the starting sequence number when starting a TX aggregation session. ============================================= [ INFO: possible recursive locking detected ] 2.6.29-rc2-wl #21 --------------------------------------------- swapper/0 is trying to acquire lock: (_xmit_IEEE80211#2){-+..}, at: [<ffffffff80456d71>] __qdisc_run+0x221/0x290 but task is already holding lock: (_xmit_IEEE80211#2){-+..}, at: [<ffffffff80456d71>] __qdisc_run+0x221/0x290 other info that might help us debug this: 7 locks held by swapper/0: #0: (rcu_read_lock){..--}, at: [<ffffffff80442a63>] dev_queue_xmit+0x53/0x620 #1: (_xmit_ETHER#2){-+..}, at: [<ffffffff80456d71>] __qdisc_run+0x221/0x290 #2: (rcu_read_lock){..--}, at: [<ffffffff80442a63>] dev_queue_xmit+0x53/0x620 #3: (_xmit_IEEE80211#2){-+..}, at: [<ffffffff80456d71>] __qdisc_run+0x221/0x290 #4: (rcu_read_lock){..--}, at: [<ffffffffa0154919>] ieee80211_master_start_xmit+0x219/0x6c0 [mac80211] #5: (rcu_read_lock){..--}, at: [<ffffffffa01427c6>] ieee80211_start_tx_ba_session+0x66/0x4e0 [mac80211] #6: (rcu_read_lock){..--}, at: [<ffffffff80442a63>] dev_queue_xmit+0x53/0x620 stack backtrace: Pid: 0, comm: swapper Not tainted 2.6.29-rc2-wl #21 Call Trace: <IRQ> [<ffffffff8026c329>] __lock_acquire+0x1be9/0x1c40 [<ffffffff80442af1>] dev_queue_xmit+0xe1/0x620 [<ffffffff8026a8cc>] __lock_acquire+0x18c/0x1c40 [<ffffffff8026c3d5>] lock_acquire+0x55/0x70 [<ffffffff80456d71>] __qdisc_run+0x221/0x290 [<ffffffff804dbeb9>] _spin_lock+0x39/0x50 [<ffffffff80456d71>] __qdisc_run+0x221/0x290 [<ffffffff804dbd2f>] _spin_unlock+0x1f/0x50 [<ffffffff80456d71>] __qdisc_run+0x221/0x290 [<ffffffff80442d18>] dev_queue_xmit+0x308/0x620 [<ffffffff80442a63>] dev_queue_xmit+0x53/0x620 [<ffffffffa0142a63>] ieee80211_start_tx_ba_session+0x303/0x4e0 [mac80211] [<ffffffffa01427c6>] ieee80211_start_tx_ba_session+0x66/0x4e0 [mac80211] [<ffffffffa0149dae>] rate_control_get_rate+0xae/0xc0 [mac80211] [<ffffffffa01526b5>] invoke_tx_handlers+0x655/0x1000 [mac80211] [<ffffffff802699fd>] mark_held_locks+0x4d/0x90 [<ffffffff804dbcf5>] _spin_unlock_irqrestore+0x65/0x80 [<ffffffffa0151aaa>] __ieee80211_tx_prepare+0x16a/0x310 [mac80211] [<ffffffffa0151adc>] __ieee80211_tx_prepare+0x19c/0x310 [mac80211] [<ffffffff80439cc2>] pskb_expand_head+0x112/0x190 [<ffffffffa0154986>] ieee80211_master_start_xmit+0x286/0x6c0 [mac80211] [<ffffffffa0154919>] ieee80211_master_start_xmit+0x219/0x6c0 [mac80211] [<ffffffff8026a8cc>] __lock_acquire+0x18c/0x1c40 [<ffffffff80456d8e>] __qdisc_run+0x23e/0x290 [<ffffffff80442d18>] dev_queue_xmit+0x308/0x620 [<ffffffff80442a63>] dev_queue_xmit+0x53/0x620 [<ffffffffa0154221>] ieee80211_subif_start_xmit+0x4a1/0x980 [mac80211] [<ffffffffa0153f18>] ieee80211_subif_start_xmit+0x198/0x980 [mac80211] [<ffffffff80456d8e>] __qdisc_run+0x23e/0x290 [<ffffffff80442d18>] dev_queue_xmit+0x308/0x620 [<ffffffff80442a63>] dev_queue_xmit+0x53/0x620 [<ffffffffa028ecfd>] ip6_output+0x62d/0x1230 [ipv6] [<ffffffff8024ca00>] __mod_timer+0xb0/0xd0 [<ffffffffa02ad25a>] mld_sendpack+0x3fa/0x4a0 [ipv6] [<ffffffffa02ace60>] mld_sendpack+0x0/0x4a0 [ipv6] [<ffffffffa02adf90>] mld_ifc_timer_expire+0x0/0x340 [ipv6] [<ffffffffa02ae219>] mld_ifc_timer_expire+0x289/0x340 [ipv6] [<ffffffffa02adf90>] mld_ifc_timer_expire+0x0/0x340 [ipv6] [<ffffffff8024c097>] run_timer_softirq+0x147/0x220 [<ffffffff802473fb>] __do_softirq+0x9b/0x180 [<ffffffff80265516>] tick_dev_program_event+0x36/0xb0 [<ffffffff8020d77c>] call_softirq+0x1c/0x30 [<ffffffff8020f2c5>] do_softirq+0x65/0xb0 [<ffffffff80246ebd>] irq_exit+0x9d/0xc0 [<ffffffff80221db6>] smp_apic_timer_interrupt+0x86/0xd0 [<ffffffff8020d1b3>] apic_timer_interrupt+0x13/0x20 Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Validate firmware in driverIvo van Doorn2009-02-095-34/+68
| | | | | | | | | | | | | The get_firmware_crc() callback function isn't flexible enough when dealing with multiple firmware versions. It might in some cases be possible that the firmware file contains multiple CRC checksums. Create the check_firmware() callback function where the driver has complete freedom in how to validate the firmware. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add kill_tx_queue callback functionIvo van Doorn2009-02-0912-72/+145
| | | | | | | | | | provide rt2x00lib the possibility to kill a particular TX queue. This can be useful when disabling the radio, but more importantly will allow beaconing to be disabled when mac80211 requests this (during scanning for example) Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Move intf_work to mac82011 workqueueIvo van Doorn2009-02-091-1/+1
| | | | | | | | | ieee80211_iterate_active_interfaces() no longer acquires the RTNL lock which means the intf_work handler can be safely used from the mac80211 workqueue again. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: unify iwlagn and 3945 power save managementWinkler, Tomas2009-02-095-242/+60
| | | | | | | | | | | This patch unifies 3945 and iwlagn power save management This patch also better separates system state from user setting. System state shall be removed later as this shall be shifted to user space Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: don't use implicit priv in IWL_DEBUGTomas Winkler2009-02-0922-839/+859
| | | | | | | | | Call IWL_DEBUG macro with explicit priv argument. Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: check return value of pci_enable_deviceWinkler, Tomas2009-02-092-2/+8
| | | | | | | | | pci_enable_device is tagged with __must_check therefore don't ignore the return value in pci_resume handlers Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: iwl3945_send_tx_power must be staticWinkler, Tomas2009-02-091-1/+1
| | | | | | | | iwl3945_send_tx_power must be static Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: suppress unused variable warning when compiling w/o IWLWIFI_DEBUGWinkler, Tomas2009-02-092-6/+6
| | | | | | | | | | This patch adds __maybe_unused attribute to priv variables used in functions that used it solely for debug printouts Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.1 at 2025-02-14 06:58:29 +0000