aboutsummaryrefslogtreecommitdiffstats
path: root/arch/avr32/mach-at32ap
Commit message (Collapse)AuthorAgeFilesLines
* PM / AVR32: Use struct syscore_ops instead of sysdevs for PMRafael J. Wysocki2011-05-111-26/+12
| | | | | | | | | | | | | Convert some AVR32 architecture's code to using struct syscore_ops objects for power management instead of sysdev classes and sysdevs. This simplifies the code and reduces the kernel's memory footprint. It also is necessary for removing sysdevs from the kernel entirely in the future. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
* don't check platform_get_irq's return value against zeroUwe Kleine-König2011-04-131-1/+1
| | | | | | | | | | | | | platform_get_irq returns -ENXIO on failure, so !int_irq was probably always true. Better use (int)int_irq <= 0. Note that a return value of zero is still handled as error even though this could mean irq0. This is a followup to 305b3228f9ff4d59f49e6d34a7034d44ee8ce2f0 that changed the return value of platform_get_irq from 0 to -ENXIO on error. Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
* avr32: fix deadlock when reading clock list in debugfsOle Henrik Jahren2011-04-131-8/+16
| | | | | | | | | | | When writing out /sys/kernel/debug/at32ap_clk, clock list lock is being held while clk_get() is called. clk_get() attempts to take the same lock, which results in deadlock. Introduce and call lock free version, __clk_get(), instead. Signed-off-by: Ole Henrik Jahren <olehenja@alumni.ntnu.no> Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
* avr32: Fix .size directive for cpu_enter_idleBen Hutchings2011-04-131-1/+1
| | | | | | | | | gas used to accept (and ignore?) .size directives which referred to undefined symbols, as this does. In binutils 2.21 these are treated as errors. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
* avr32: At32ap: pio fix typo "))" on gpio_irq_unmask prototypeJean-Christophe PLAGNIOL-VILLARD2011-04-131-1/+1
| | | | | | | | | | | introduce in commit d75f1bfdbccb Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Patrice Vilchez <patrice.vilchez@atmel.com> Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
* fix the wrong argument of the functions definitionWanlong Gao2011-04-131-10/+10
| | | | | | | The functions of eic_chip's memebers use the wrong argument . Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com> Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
* avr32: Fix missing irq namespace conversionThomas Gleixner2011-03-301-1/+1
| | | | Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* avr32: Cleanup eic_set_irq_type()Thomas Gleixner2011-03-241-20/+11
| | | | | | | | | No need to fiddle in irq_desc. The trigger mask can be written back into irq_data. Return IRQ_SET_MASK_OK_NOCOPY, so the generic code wont overwrite it again. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
* avr: Cleanup genirq namespaceThomas Gleixner2011-03-243-15/+15
| | | | | | | Scripted conversion to new function names with coccinelle. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
* avr32: At32ap: Convert pop irq_chip to new functionsThomas Gleixner2011-03-241-13/+10
| | | | | | | | Also replace the open coded handler call with the proper wrapper. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> LKML-Reference: <20110206163009.190112353@linutronix.de>
* avr32: At32ap: Convert intc irq_chip to new functionsThomas Gleixner2011-03-241-7/+5
| | | | | | | | Also replace the open coded handler call with the proper wrapper. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> LKML-Reference: <20110206163009.096308633@linutronix.de>
* avr32: At32ap: Convert extint irq_chip to new functionsThomas Gleixner2011-03-241-22/+23
| | | | | | Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> LKML-Reference: <20110206163008.996220791@linutronix.de>
* avr32: at32ap700x: fix typo in DMA master configurationJamie Iles2011-03-221-2/+2
| | | | | | | | | | | | | | Commit 4aa5f366431fe (avr32: at32ap700x: specify DMA src and dst masters) specified the masters for the ac97c playback device but incorrectly set them in the capture slave information rather than playback. Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Vinod Koul <vinod.koul@intel.com> [rebased on dmaengine for 2.6.39 (d42efe6b)] Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* avr32: at32ap700x: Specify DMA Flow Controller, Src and Dst msizeViresh Kumar2011-03-071-0/+9
| | | | | | | | | | Now that the dw_dmac DMA driver supports configurable Flow Controller, source and destination burst or msize, we need to specify which ones to use. Msize or burst size was previously hardcoded to 1, Flow controller was DMA for both M2P & P2M transfers. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* Merge branch 'dw_dmac' into dmaengineDan Williams2011-02-141-0/+6
|\
| * avr32: at32ap700x: specify DMA src and dst mastersJamie Iles2011-01-291-0/+6
| | | | | | | | | | | | | | | | | | | | Now that the dw_dmac DMA driver supports configurable source and destination masters we need to specify which ones to use. This was previously hardcoded to 0 and 1 respectively in the driver. Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* | suspend: constify platform_suspend_opsLionel Debroux2010-11-161-1/+1
|/ | | | | | | | | | | | | | While at it, fix two checkpatch errors. Several non-const struct instances constified by this patch were added after the introduction of platform_suspend_ops in checkpatch.pl's list of "should be const" structs (79404849e90a41ea2109bd0e2f7c7164b0c4ce73). Patch against mainline. Inspired by hunks of the grsecurity patch, updated for newer kernels. Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* serial: fix rs485 for atmel_serial on avr32Peter Huewe2010-07-261-0/+2
| | | | | | | | | | | | | | | | | This patch fixes a build failure [1-4] in the atmel_serial code introduced by patch the patch ARM: 6092/1: atmel_serial: support for RS485 communications (e8faff7330a3501eafc9bfe5f4f15af444be29f5) The build failure was caused by missing struct field and missing defines for the avr32 board - the patch fixes this. [1] http://kisskb.ellerman.id.au/kisskb/buildresult/2575242/ - first failure in linux-next, may 11th [2] http://kisskb.ellerman.id.au/kisskb/buildresult/2816418/ - still exists as of today [3] http://kisskb.ellerman.id.au/kisskb/buildresult/2617511/ - first failure in Linus' tree - May 20th - did really no one notice this?! [4] http://kisskb.ellerman.id.au/kisskb/buildresult/2813956/ - still exists in Linus' tree as of today Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* include cleanup: Update gfp.h and slab.h includes to prepare for breaking ↵Tejun Heo2010-03-303-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* USB: atmel uaba: Adding invert vbus_pinEirik Aanonsen2010-03-021-2/+5
| | | | | | | | | | | Adding vbus_pin_inverted so that the usb detect pin can be active high or low depending on HW implementation also replaced the gpio_get_value(udc->vbus_pin); with a call to vbus_is_present(udc); This allows the driver to be loaded and save about 0,15W on the consumption. Signed-off-by: Eirik Aanonsen <eaa@wprmedical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* avr32: clean up memory allocation in at32_add_device_mciHans-Christian Egtvedt2009-12-281-4/+7
| | | | | | | | | | | | This patch will check if the kzalloc for the MCI DMA struct actually returns a valid address, and also clean up properly if it fails or the function fails at a later stage. This also silences a compiler warning about using the slave variable uninitialized. Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* arch/avr32: Fix build failure for avr32 caused by typoPeter Huewe2009-12-281-2/+2
| | | | | | | | | | | | | | | | | This patch fixes a build failure introduced by the patch atmel-mci: change use of dma slave interface by Nicolas Ferre by changing mci_dma_slave to the correct name of mci_dma_data This should make the avr32 tree build again. References: http://kisskb.ellerman.id.au/kisskb/buildresult/1893610/ http://git.kernel.org/?p=linux/kernel/git/sfr/linux-next.git;a=commitdiff;h=2635d1ba711560d521f6218c585a3e0401f566e1 Patch against Linus' tree. Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6Linus Torvalds2009-12-152-16/+20
|\ | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6: avr32: update default configurations for ATNGW100, ATSTK1002 and ATSTK1006 avr32: add default configurations for ATNGW100 mkII and EVKLCD10X avr32: add support for ATNGW100 mkII board avr32: convert to asm-generic/hardirq.h avr32: add two new at91 to cpu.h definition avr32: clean up linker script using standard macros. avr32: MRMT: correct setup of SPI slaves avr32: function for independently setting up SPI slaves avr32: re-instate MCI WP/CD pin assignments for ATNGW100
| * Merge commit 'v2.6.32'Haavard Skinnemoen2009-12-141-0/+1
| |\ | | | | | | | | | | | | Conflicts: arch/avr32/mach-at32ap/include/mach/cpu.h
| * | avr32: add two new at91 to cpu.h definitionNicolas Ferre2009-10-061-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Somme common drivers will need those at91 cpu_is_xxx() definitions. As at91sam9g10 and at91sam9g45 are on the way to linus' tree, here is the patch that adds those chips to cpu.h in AVR32 architecture. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
| * | avr32: function for independently setting up SPI slavesPeter Ma2009-08-272-16/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | at32ap_spi_setup_slaves() is exposed to allow the addition of SPI slaves to a SPI bus that has already been registered. This is especially useful for add-on cards, which have their own board setup function. at32ap_spi_add_device() has been slightly re-organized, but should be transparent to existing users. So to add a SPI slave, after a SPI bus has already been registered: /* Configure the list of slaves on SPI controller "id" */ at32_spi_setup_slaves(id,spi_board_info,ARRAY_SIZE(spi_board_info)); /* Register the list of slaves */ spi_register_board_info(spi_board_info,ARRAY_SIZE(spi_board_info)); Signed-off-by: Peter Ma <pma@mediamatech.com> [haavard.skinnemoen@atmel.com: trivial whitespace fix] Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* | | atmel-mci: change use of dma slave interfaceNicolas Ferre2009-12-152-5/+37
| |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Allow the use of another DMA controller driver in atmel-mci sd/mmc driver. This adds a generic dma_slave pointer to the mci platform structure where we can store DMA controller information. In atmel-mci we use information provided by this structure to initialize the driver (with new helper functions that are architecture dependant). This also adds at32/avr32 chip modifications to cope with this new access method. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | at91: at91sam9g45 family: identify several chip versionsNicolas Ferre2009-11-031-0/+1
| | | | | | | | | | | | | | | | | | | | | | cpu_is_xxx() macros are identifying generic at91sam9g45 chip. This patch adds the capacity to differentiate Engineering Samples and final lots through the inclusion of at91_cpu_fully_identify() and the related chip IDs with chip version field preserved. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
* | avr32: add two new at91 to cpu.h definitionNicolas Ferre2009-11-031-0/+2
|/ | | | | | | | | Somme common drivers will need those at91 cpu_is_xxx() definitions. As at91sam9g10 and at91sam9g45 are on the way to linus' tree, here is the patch that adds those chips to cpu.h in AVR32 architecture. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* avr32: Fix clash in ATMEL_USART_ flagsBen Nizette2009-06-031-1/+1
| | | | | | | | | | | | At the moment ATMEL_USART_{RTS,CTS,CLK} have the values 1, 2 and 3 respectively. Given these are used in bitmasks, trying to turn on the CLK line will in fact turn on the RTS and CTS lines as well. Change the value of ATMEL_USART_CLK to 4. Signed-off-by: Ben Nizette <bn@niasdigital.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* dma-mapping: replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)Yang Hongyang2009-04-071-4/+4
| | | | | | | | Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32) Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* avr32: add RTS/CTS/CLK pin selection for the USARTsPeter Ma2009-04-012-10/+27
| | | | | | | | | | | Adds extra parameter to AT32 at32_map_usart(), so as to reserve RTS/CTS/CLK pins. All boards under arch/avr32/boards have been updated (trivial change), but not all have been tested. Signed-off-by: Peter Ma <pma@mediamatech.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* avr32: at32ap700x: setup DMA for AC97C in the machine codeHans-Christian Egtvedt2009-03-272-23/+38
| | | | | | | | | | | | | | | | | | | | This patch will adjust the setup the DMA controller for the AC97 Controller in the at32ap700x machine code. This setup matches the new ALSA driver for the AC97C. The struct ac97c_platform_data has been moved into its own header file located in the sound include path. Tested on ATSTK1006 + ATSTK1000. This patch will setup the AC97 controller properly for the adjusted machine code. Both EVKLCD10x and Hammerhead board has been updated. Tested on EVKLCD10x, and copied to Hammerhead board. Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> [haavard.skinnemoen@atmel.com: fold with board code update] Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* avr32: at32ap700x: setup DMA for ABDAC in the machine codeHans-Christian Egtvedt2009-03-272-9/+27
| | | | | | | | | | | | | | | This patch will adjust the setup the DMA controller for the Audio Bistream DAC in the at32ap700x machine code. This setup matches the new ALSA driver for the ABDAC. Tested on ATSTK1006 + ATSTK1000. This patch will setup the needed platform data for the Audio Bistream DAC used by the Favr-32 board. Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> [haavard.skinnemoen@atmel.com: fold board code update] Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* Merge branch 'master' of ↵Haavard Skinnemoen2009-03-271-0/+1
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into avr32-arch
| * [ARM] 5400/1: Add support for inverted rdy_busy pin for Atmel nand device ↵Gregory CLEMENT2009-02-161-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | controller Add support for inverted rdy_busy pin for Atmel nand device controller It will fix building error on NeoCore926 board. Acked-by: Andrew Victor <linux@maxim.org.za> Acked-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Gregory CLEMENT <gclement@adeneo.adetelgroup.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* | avr32: use gpio_is_valid() to check USBA vbus_pin I/O lineHans-Christian Egtvedt2009-03-261-1/+1
| | | | | | | | | | | | | | This patch will use gpio_is_valid() to check the vbus_pin I/O line. Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* | avr32: add pin mask for 18-bit color on the LCD controllerHans-Christian Egtvedt2009-03-261-0/+26
| | | | | | | | | | | | | | | | | | This patch adds two defines for setting a pin mask for 18-bit LCD panels connected to the LCD controller. One mask for primary output and one mask for alternative output. Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* | avr32: fix 15-bit LCDC pin mask to use MSB linesHans-Christian Egtvedt2009-03-261-16/+18
|/ | | | | | | | | | | This patch corrects the 15-bit LCDC pin mask definitions to select the five upper lines in each color byte from the LCDC data output. When reducing the color depth the LCDC will start filling MSB and downwards. Also only enable 5 bits per color as the define indicates. Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* Merge branch 'next' of ↵Linus Torvalds2009-01-091-12/+3
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (22 commits) ioat: fix self test for multi-channel case dmaengine: bump initcall level to arch_initcall dmaengine: advertise all channels on a device to dma_filter_fn dmaengine: use idr for registering dma device numbers dmaengine: add a release for dma class devices and dependent infrastructure ioat: do not perform removal actions at shutdown iop-adma: enable module removal iop-adma: kill debug BUG_ON iop-adma: let devm do its job, don't duplicate free dmaengine: kill enum dma_state_client dmaengine: remove 'bigref' infrastructure dmaengine: kill struct dma_client and supporting infrastructure dmaengine: replace dma_async_client_register with dmaengine_get atmel-mci: convert to dma_request_channel and down-level dma_slave dmatest: convert to dma_request_channel dmaengine: introduce dma_request_channel and private channels net_dma: convert to dma_find_channel dmaengine: provide a common 'issue_pending_all' implementation dmaengine: centralize channel allocation, introduce dma_find_channel dmaengine: up-level reference counting to the module level ...
| * atmel-mci: convert to dma_request_channel and down-level dma_slaveDan Williams2009-01-061-12/+3
| | | | | | | | | | | | | | | | | | | | | | dma_request_channel provides an exclusive channel, so we no longer need to pass slave data through dmaengine. Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* | Merge branch 'move-atmel-mci-h' into boardsHaavard Skinnemoen2009-01-051-1/+1
|\ \
| * | atmel-mci: move atmel-mci.h file to include/linuxNicolas Ferre2009-01-051-1/+1
| |/ | | | | | | | | | | | | | | Needed to use the atmel-mci driver in an architecture independant maner. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* | avr32: Hammerhead board supportAlex Raimondi2009-01-052-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Hammerhead platform is built around a AVR32 32-bit microcontroller from Atmel. It offers versatile peripherals, such as ethernet, usb device, usb host etc. The board also incooperates a power supply and is a Power over Ethernet (PoE) Powered Device (PD). Additonally, a Cyclone III FPGA from Altera is integrated on the board. The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two DDR2 SDRAM interfaces, which will cover even the most exceptional need of memory bandwidth. Together with the onboard video decoder the board is ready for video processing. This patch does include the basic support for the fpga device driver, but not the device driver itself. Signed-off-by: Alex Raimondi <mailinglist@miromico.ch> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* | Merge branch 'cleanups' into boardsHaavard Skinnemoen2009-01-054-9/+19
|\ \ | |/ |/|
| * avr32: Allow reserving multiple pins at onceAlex Raimondi2009-01-053-7/+17
| | | | | | | | | | | | | | | | | | | | | | at32_reserve_pin now takes an u32 bitmask rather than a single pin. This allows to reserve multiple pins at once. Remove (undocumented) SDCS (pin PE26) from reservation in board setup code. Signed-off-by: Alex Raimondi <raimondi@miromico.ch> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
| * avr: struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers2009-01-051-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | (I did not compile or test it, please let me know, or help fixing it, if something is wrong with the conversion) This patch is part of a larger patch series which will remove the "char bus_id[20]" name string from struct device. The device name is managed in the kobject anyway, and without any size limitation, and just needlessly copied into "struct device". To set and read the device name dev_name(dev) and dev_set_name(dev) must be used. If your code uses static kobjects, which it shouldn't do, "const char *init_name" can be used to statically provide the name the registered device should have. At registration time, the init_name field is cleared, to enforce the use of dev_name(dev) to access the device name at a later time. We need to get rid of all occurrences of bus_id in the entire tree to be able to enable the new interface. Please apply this patch, and possibly convert any remaining remaining occurrences of bus_id. We want to submit a patch to -next, which will remove bus_id from "struct device", to find the remaining pieces to convert, and finally switch over to the new api, which will remove the 20 bytes array and does no longer have a size limitation. Thanks, Kay From: Kay Sievers <kay.sievers@vrfy.org> Subject: avr: struct device - replace bus_id with dev_name(), dev_set_name() Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* | avr32: Enable pullup on USART TX linesAnders Blomdell2008-10-241-4/+4
|/ | | | | | | | | | Make USART initialization conform to Section 24.6.1 in the AT32AP7000 manual, i.e. "To prevent the TXD line from falling when the USART is disabled, the use of an internal pull up is mandatory." Signed-off-by: Anders Blomdell <anders.blomdell@control.lth.se> [haavard.skinnemoen@atmel.com: enable pullup on RX as well] Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* Merge branches 'boards' and 'fixes' of ↵Haavard Skinnemoen2008-10-234-9/+31
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6
| * avr32: Fix GPIO initcall breakageHaavard Skinnemoen2008-10-232-3/+12
| | | | | | | | | | | | | | | | | | | | Add essential system devices, including GPIO controllers, automatically at core_initcall time. This ensures that the devices are there when the PIO driver gets initialized at postcore_initcall, fixing a bug exposed by commit d6634db8fe1784d0a8e4e156970fec034708446e "avr32: Use platform_driver_probe for pio platform driver". Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
generated by cgit v1.1 at 2024-12-26 16:54:54 +0000