aboutsummaryrefslogtreecommitdiffstats
path: root/drivers
Commit message (Collapse)AuthorAgeFilesLines
* [PATCH] libata: make per-dev transfer mode limits per-devTejun Heo2006-03-242-2/+2
| | | | | | | | Now that each ata_device has xfer masks, per-dev limits can be made per-dev instead of per-port. Make per-dev limits per-dev. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] libata: add per-dev pio/mwdma/udma_maskTejun Heo2006-03-241-18/+25
| | | | | | | | | | Add per-dev pio/mwdma/udma_mask. All transfer mode limits used to be applied to ap->*_mask which unnecessarily restricted other devices sharing the port. This change will also benefit later EH speed down and hotplug. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] libata: implement ata_unpack_xfermask()Tejun Heo2006-03-241-0/+23
| | | | | | | Implement ata_unpack_xfermask(). Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] Move some bmdma-specific code to libata-bmdma.cJeff Garzik2006-03-232-234/+234
| | | | No code changes, just moving code between files.
* [libata sata_uli] kill scr_addr abuseJeff Garzik2006-03-231-10/+27
| | | | | | | | sata_uli was storing PCI config addresses in a variable intended for port addresses, a variable soon to become void __iomem *. Update the driver to store the SCR address, found in PCI config space, in the driver-private data area.
* [libata sata_nv] eliminate duplicate codepaths with iomapJeff Garzik2006-03-221-44/+13
| | | | | | | | | | eliminate a bunch of if (mmio) writel() else outl() code with the pci_iomap() and io{read,write}{8,16,32}() interface.
* [libata sata_nv] cleanups: convert #defines to enums; remove in-file historyJeff Garzik2006-03-221-75/+49
|
* [libata sata_sil24] cleanups: use pci_iomap(), kzalloc()Jeff Garzik2006-03-221-13/+10
| | | | | | * libata will soon move to iomap, so we should use pci_iomap() and pci_iounmap(). * Use kzalloc() where appropriate.
* Merge branch 'upstream-linus' of ↵Linus Torvalds2006-03-2210-136/+104
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6 * 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: [PATCH] Use of uninitialized variable in drivers/net/depca.c [PATCH] Use after free in net/tulip/de2104x.c [PATCH] sis900 adm7001 PHY support [PATCH] sky2: more ethtool stats [PATCH] s390: qeth :allow setting of attribute "route6" to "no_router". [PATCH] s390: qeth driver cleanups [PATCH] s390: qeth driver statistics fixes [PATCH] AMD Au1xx0: fix Ethernet TX stats [PATCH] fix spidernet build issue
| * [PATCH] Use of uninitialized variable in drivers/net/depca.cEric Sesterhenn2006-03-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | hi, this fixes coverity bug #888, where the variable dev is used uninitialized. I assume the programmer meant to use mdev, which is initialized. Compile tested only. Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * [PATCH] Use after free in net/tulip/de2104x.cEric Sesterhenn2006-03-221-1/+1
| | | | | | | | | | | | | | | | | | | | hi, this fixes coverity bug #912, where skb is freed first, and dereferenced a few lines later with skb->len. Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * [PATCH] sis900 adm7001 PHY supportArtur Skawina2006-03-221-0/+1
| | | | | | | | | | | | | | | | | | this patch is required to get a SIS964 based motherboard ethernet working (FSC D1875) (picking the #1 transceiver, instead of the last one, in case no known ones were found might be a better default, and would have worked in this case too) Signed-off-by: Artur Skawina <art_k@o2.pl> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * [PATCH] sky2: more ethtool statsStephen Hemminger2006-03-222-41/+57
| | | | | | | | | | | | | | | | Expose all the available hardware statistics via ethtool. And cleanup some of the statistics definitions. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * [PATCH] s390: qeth :allow setting of attribute "route6" to "no_router".Frank Pavlic2006-03-221-5/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [patch 4/6] s390: qeth :allow setting of attribute "route6" to "no_router". From: Ursula Braun <braunu@de.ibm.com> when setting route6 attribute back to no_router qeth does not issue an IP ASSIST command to reset router value to no_router. Once primary_router is set device stays in this mode. Issue an IP ASSIST command when no_router is set in route6. Device will be reset and thus will not longer run as a primary router. Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com> diffstat: qeth_main.c | 5 ----- 1 files changed, 5 deletions(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * [PATCH] s390: qeth driver cleanupsFrank Pavlic2006-03-223-55/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [patch 3/6] s390: qeth driver cleanups From: Ursula Braun <braunu@de.ibm.com> - code analyzing tool BEAM has found some unreachable and unnecessary statements and also conditions which are always true. - removed some useless MII code since OSA card will never allow to set such values. Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com> diffstat: qeth_main.c | 49 ++++--------------------------------------------- qeth_proc.c | 18 +++++++++--------- qeth_sys.c | 2 +- 3 files changed, 14 insertions(+), 55 deletions(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * [PATCH] s390: qeth driver statistics fixesFrank Pavlic2006-03-222-20/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [patch 2/6] s390: qeth driver statistics fixes From: Ursula Braun <braunu@de.ibm.com> - display "unsigned int" values in /proc/qeth_perf with %u instead of %i - omit qdio header length when increasing card->stats.tx_bytes Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com> diffstat: qeth_main.c | 3 ++- qeth_proc.c | 38 +++++++++++++++++++------------------- 2 files changed, 21 insertions(+), 20 deletions(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * [PATCH] AMD Au1xx0: fix Ethernet TX statsSergei Shtylylov2006-03-221-11/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With Au1xx0 Ethernet driver, TX bytes/packets always remain zero. The problem seems to be that when packet has been transmitted, the length word in DMA buffer is zero. The patch updates the TX stats when a buffer is fed to DMA. The initial 2.4 patch was posted to linux-mips@linux-mips.org by Thomas Lange 21 Jan 2005. Signed-off-by: Thomas Lange <thomas@corelatus.se> Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Jordan Crouse <jordan.crouse@amd.com> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * [PATCH] fix spidernet build issueJens Osterkamp2006-03-221-2/+2
| | | | | | | | | | | | | | | | <unchangelogged> Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | scsi: link in the debug driver lastLinus Torvalds2006-03-221-1/+3
| | | | | | | | | | | | | | | | | | | | | | If the debug driver is built-in, link it in last, so that any real drivers will probe first, rather than having the debug driver pick the first scsi slots.. Signed-off-by: Douglas Gilbert <dougg@torque.net> Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Acked-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | Merge master.kernel.org:/home/rmk/linux-2.6-serialLinus Torvalds2006-03-2225-358/+205
|\ \ | | | | | | | | | | | | | | | * master.kernel.org:/home/rmk/linux-2.6-serial: [SERIAL] Merge avlab serial board entries in parport_serial [SERIAL] kernel console should send CRLF not LFCR
| * | [SERIAL] Merge avlab serial board entries in parport_serialRussell King2006-03-201-57/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | As can be seen from this patch, the avlab_*_[68]50 table entries are identical to the plain avlab_* entries in every respect. Hence, there is no need to list them separately in the pciserial_board nor parport_pc_pci card tables - they can re-use the plain avlab_* entries. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| * | [SERIAL] kernel console should send CRLF not LFCRRussell King2006-03-2024-301/+187
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Glen Turner reported that writing LFCR rather than the more traditional CRLF causes issues with some terminals. Since this aflicts many serial drivers, extract the common code to a library function (uart_console_write) and arrange for each driver to supply a "putchar" function. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* | | Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds2006-03-222-2/+2
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits) [ARM] 3389/1: typo and grammar fix [ARM] 3386/1: AT91RM9200 Clock update [ARM] 3384/1: AT91RM9200: Timer [ARM] 3382/1: ixp2000: unify defconfigs [ARM] 3381/1: ixp2000: fix slowport write timing control register fields [ARM] 3380/1: ixp2000: simplify ixdp2x00_master_npu() check [ARM] 3379/1: ixp2000: use generic 8250 debug macros [ARM] 3378/1: ixp2000: fix gpio interrupt handling [ARM] Quieten spurious IRQ detection [ARM] Use kcalloc to allocate counter_config array rather than kmalloc [ARM] Oprofile: dynamically allocate counter_config [ARM] Oprofile: Convert semaphore to mutex [ARM] 3376/2: S3C2410 - update defconfig [ARM] 3375/1: S3C2440 - fix osiris machine build [ARM] 3374/1: ep93xx: gpio interrupt support [ARM] 3361/1: S3C24XX - add USB bus clock source [ARM] 3360/1: S3C2440 - add set rate methods and camera clock [ARM] 3359/1: S3C24XX - add support for clk_set_rate [ARM] Convert kmalloc+memset to kzalloc [ARM] 3373/1: move uengine loader to arch/arm/common ...
| * | | [ARM] 3373/1: move uengine loader to arch/arm/commonLennert Buytenhek2006-03-212-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Patch from Lennert Buytenhek Move the uengine loader from arch/arm/mach-ixp2000 to arch/arm/common so that ixp23xx can use it too. Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* | | | [PATCH] ahci: add softresetTejun Heo2006-03-221-1/+134
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that libata is smart enought to handle both soft and hard resets, add softreset method. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | | | [PATCH] libata: do not ignore PIO-only devicesTejun Heo2006-03-221-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | As libata now can do PIO, don't ignore PIO-only devices. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | | | [PATCH] libata: Symbol exportsAlan Cox2006-03-221-0/+2
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | | | [PATCH] Update libata DMA blacklist to cover versions, and resync with IDE layerAlan Cox2006-03-221-35/+59
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Not much to say here except that some drives have fixed and bad firmware Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | | | [PATCH] libata: Fix a drive detection problemAlan Cox2006-03-221-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current code follows the spec but uses an overlong delay. This would be great if the hardware did. Several vendors however forget the D7 pulldown. Fortunately 0xFF isnt a sane reset state so we can use it to skip detection as is done in drivers/ide. (ie this is a tested solution over a long time) Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | | | [PATCH] libata: note missing posting in mmio cmd writeAlan Cox2006-03-221-0/+2
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | | | Merge branch 'master'Jeff Garzik2006-03-22142-42897/+35717
|\ \ \ \
| * \ \ \ Merge git://git.kernel.org/pub/scm/linux/kernel/git/perex/alsaLinus Torvalds2006-03-223-55/+66
| |\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/perex/alsa: (124 commits) [ALSA] version 1.0.11rc4 [PATCH] Intruduce DMA_28BIT_MASK [ALSA] hda-codec - Add support for ASUS P4GPL-X [ALSA] hda-codec - Add support for HP nx9420 laptop [ALSA] Fix memory leaks in error path of control.c [ALSA] AMD Au1x00: AC'97 controller is memory mapped [ALSA] AMD Au1x00: fix DMA init/cleanup [ALSA] hda-codec - Fix generic auto-configurator [ALSA] hda-codec - Fix BIOS auto-configuration [ALSA] Fixes typos in Audiophile-USB.txt [ALSA] ice1712 - typo fixes for dxr_enable module option [ALSA] AMD Au1x00: make driver build after cleanup [ALSA] ice1712 - Fix wrong value types for enum items [ALSA] fix resource leak in usbmixer [ALSA] Fix gus_pcm dereference before NULL [ALSA] Fix seq_clientmgr dereferences before NULL check [ALSA] hda-codec - Fix for Samsung R65 and ASUS A6J [ALSA] hda-codec - Add support for VAIO FE550G and SZ110 [ALSA] usb-audio: add Maya44 mixer control names [ALSA] usb-audio: add Casio PL-40R support ...
| | * \ \ \ Merge with ↵Jaroslav Kysela2006-03-22432-20518/+32250
| | |\ \ \ \ | | | | |_|/ | | | |/| | | | | | | | rsync://rsync.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
| | * | | | [ALSA] Fix snd_xxx_t typedefsTakashi Iwai2006-03-223-55/+66
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Modules: PXA Mainstone driver,CX88 driver,SAA7134 driver Replace snd_xxx_t typedefs with explicit structs. Signed-off-by: Takashi Iwai <tiwai@suse.de>
| * | | | | Merge git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivialLinus Torvalds2006-03-225-5/+5
| |\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: fixed path to moved file in include/linux/device.h Fix spelling in E1000_DISABLE_PACKET_SPLIT Kconfig description Documentation/dvb/get_dvb_firmware: fix firmware URL Documentation: Update to BUG-HUNTING Remove superfluous NOTIFY_COOKIE_LEN define add "tags" to .gitignore Fix "frist", "fisrt", typos fix rwlock usage example It's UTF-8
| | * | | | | Fix spelling in E1000_DISABLE_PACKET_SPLIT Kconfig descriptionJames Ring2006-03-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Adrian Bunk <bunk@stusta.de>
| | * | | | | Fix "frist", "fisrt", typosUwe Zeisberger2006-03-224-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com> Signed-off-by: Adrian Bunk <bunk@stusta.de>
| * | | | | | Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds2006-03-224-9/+5
| |\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: [SPARC64]: Add a secondary TSB for hugepage mappings. [SPARC]: Respect vm_page_prot in io_remap_page_range().
| | * | | | | | [SPARC]: Respect vm_page_prot in io_remap_page_range().David S. Miller2006-03-224-9/+5
| | | |_|/ / / | | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make sure the callers do a pgprot_noncached() on vma->vm_page_prot. Pointed out by Hugh Dickens. Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | | Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds2006-03-221-7/+25
| |\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: [TG3]: Bump driver version and reldate. [TG3]: Skip phy power down on some devices [TG3]: Fix SRAM access during tg3_init_one() [X25]: dte facilities 32 64 ioctl conversion [X25]: allow ITU-T DTE facilities for x25 [X25]: fix kernel error message 64 bit kernel [X25]: ioctl conversion 32 bit user to 64 bit kernel [NET]: socket timestamp 32 bit handler for 64 bit kernel [NET]: allow 32 bit socket ioctl in 64 bit kernel [BLUETOOTH]: Return negative error constant
| | * | | | | | [TG3]: Bump driver version and reldate.David S. Miller2006-03-221-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | | | | [TG3]: Skip phy power down on some devicesMichael Chan2006-03-221-2/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some PHYs should not be powered down in tg3_set_power_state() because of bugs or other hardware limitations. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | | | | [TG3]: Fix SRAM access during tg3_init_one()Michael Chan2006-03-221-3/+9
| | |/ / / / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 5700 and 5701 will not return correct SRAM data when the chip is in D3hot power state. tg3_get_eeprom_hw_cfg() must first put the device in D0 before reading SRAM. Thanks to Thomas Chenault at Dell for noticing this problem. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | | Merge master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6Linus Torvalds2006-03-22119-42667/+35378
| |\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (138 commits) [SCSI] libata: implement minimal transport template for ->eh_timed_out [SCSI] eliminate rphy allocation in favour of expander/end device allocation [SCSI] convert mptsas over to end_device/expander allocations [SCSI] allow displaying and setting of cache type via sysfs [SCSI] add scsi_mode_select to scsi_lib.c [SCSI] 3ware 9000 add big endian support [SCSI] qla2xxx: update MAINTAINERS [SCSI] scsi: move target_destroy call [SCSI] fusion - bump version [SCSI] fusion - expander hotplug suport in mptsas module [SCSI] fusion - exposing raid components in mptsas [SCSI] fusion - memory leak, and initializing fields [SCSI] fusion - exclosure misspelled [SCSI] fusion - cleanup mptsas event handling functions [SCSI] fusion - removing target_id/bus_id from the VirtDevice structure [SCSI] fusion - static fix's [SCSI] fusion - move some debug firmware event debug msgs to verbose level [SCSI] fusion - loginfo header update [SCSI] add scsi_reprobe_device [SCSI] megaraid_sas: fix extended timeout handling ...
| | * | | | | | [SCSI] libata: implement minimal transport template for ->eh_timed_outTejun Heo2006-03-2118-16/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SCSI midlayer has moved hostt->eh_timed_out to transport template. As libata doesn't need full-blown transport support yet, implement minimal transport for libata. No transport class or whatsoever, just empty transport template with ->eh_timed_out hook. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| | * | | | | | Merge ../linux-2.6James Bottomley2006-03-21568-22239/+35113
| | |\ \ \ \ \ \ | | | | |_|_|/ / | | | |/| | | |
| | * | | | | | [SCSI] eliminate rphy allocation in favour of expander/end device allocationJames Bottomley2006-03-191-45/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This allows the removal of the contained flag and also does a bit of class renaming (sas_rphy->sas_device). Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| | * | | | | | [SCSI] convert mptsas over to end_device/expander allocationsJames Bottomley2006-03-191-5/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The conversion of mptsas should allow the elimination of the contained flag in the sas transport class. Acked-by: "Moore, Eric" <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| | * | | | | | [SCSI] allow displaying and setting of cache type via sysfsJames Bottomley2006-03-191-23/+113
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I think I promised to do this two years ago This patch adds a scsi_disk class with the cache type and FUA parameters, so user land application can easily obtain them without having to parse dmesg. It also allows setting the cache type (use with care...) This patch is a bit dangerous because I've replaced the disk kref with a class device reference ... Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| | * | | | | | [SCSI] add scsi_mode_select to scsi_lib.cJames Bottomley2006-03-191-1/+80
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This complements the scsi_mode_sense() function Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
generated by cgit v1.1 at 2025-01-14 06:45:22 +0000