diff options
Diffstat (limited to 'include/linux/spi')
| -rw-r--r-- | include/linux/spi/ad7879.h | 35 | ||||
| -rw-r--r-- | include/linux/spi/ads7846.h | 1 | ||||
| -rw-r--r-- | include/linux/spi/eeprom.h | 6 | ||||
| -rw-r--r-- | include/linux/spi/libertas_spi.h | 32 | ||||
| -rw-r--r-- | include/linux/spi/spi.h | 13 | ||||
| -rw-r--r-- | include/linux/spi/spi_gpio.h | 6 |
6 files changed, 92 insertions, 1 deletions
diff --git a/include/linux/spi/ad7879.h b/include/linux/spi/ad7879.h new file mode 100644 index 0000000..4231104 --- /dev/null +++ b/include/linux/spi/ad7879.h @@ -0,0 +1,35 @@ +/* linux/spi/ad7879.h */ + +/* Touchscreen characteristics vary between boards and models. The + * platform_data for the device's "struct device" holds this information. + * + * It's OK if the min/max values are zero. + */ +struct ad7879_platform_data { + u16 model; /* 7879 */ + u16 x_plate_ohms; + u16 x_min, x_max; + u16 y_min, y_max; + u16 pressure_min, pressure_max; + + /* [0..255] 0=OFF Starts at 1=550us and goes + * all the way to 9.440ms in steps of 35us. + */ + u8 pen_down_acc_interval; + /* [0..15] Starts at 0=128us and goes all the + * way to 4.096ms in steps of 128us. + */ + u8 first_conversion_delay; + /* [0..3] 0 = 2us, 1 = 4us, 2 = 8us, 3 = 16us */ + u8 acquisition_time; + /* [0..3] Average X middle samples 0 = 2, 1 = 4, 2 = 8, 3 = 16 */ + u8 averaging; + /* [0..3] Perform X measurements 0 = OFF, + * 1 = 4, 2 = 8, 3 = 16 (median > averaging) + */ + u8 median; + /* 1 = AUX/VBAT/GPIO set to GPIO Output */ + u8 gpio_output; + /* Initial GPIO pin state (valid if gpio_output = 1) */ + u8 gpio_default; +}; diff --git a/include/linux/spi/ads7846.h b/include/linux/spi/ads7846.h index 05eab2f..2ea2032 100644 --- a/include/linux/spi/ads7846.h +++ b/include/linux/spi/ads7846.h @@ -51,5 +51,6 @@ struct ads7846_platform_data { void **filter_data); int (*filter) (void *filter_data, int data_idx, int *val); void (*filter_cleanup)(void *filter_data); + void (*wait_for_sync)(void); }; diff --git a/include/linux/spi/eeprom.h b/include/linux/spi/eeprom.h index 1085212..306e7b1 100644 --- a/include/linux/spi/eeprom.h +++ b/include/linux/spi/eeprom.h @@ -1,6 +1,8 @@ #ifndef __LINUX_SPI_EEPROM_H #define __LINUX_SPI_EEPROM_H +#include <linux/memory.h> + /* * Put one of these structures in platform_data for SPI EEPROMS handled * by the "at25" driver. On SPI, most EEPROMS understand the same core @@ -17,6 +19,10 @@ struct spi_eeprom { #define EE_ADDR2 0x0002 /* 16 bit addrs */ #define EE_ADDR3 0x0004 /* 24 bit addrs */ #define EE_READONLY 0x0008 /* disallow writes */ + + /* for exporting this chip's data to other kernel code */ + void (*setup)(struct memory_accessor *mem, void *context); + void *context; }; #endif /* __LINUX_SPI_EEPROM_H */ diff --git a/include/linux/spi/libertas_spi.h b/include/linux/spi/libertas_spi.h new file mode 100644 index 0000000..79506f5 --- /dev/null +++ b/include/linux/spi/libertas_spi.h @@ -0,0 +1,32 @@ +/* + * board-specific data for the libertas_spi driver. + * + * Copyright 2008 Analog Devices Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or (at + * your option) any later version. + */ +#ifndef _LIBERTAS_SPI_H_ +#define _LIBERTAS_SPI_H_ + +struct spi_device; + +struct libertas_spi_platform_data { + /* There are two ways to read data from the WLAN module's SPI + * interface. Setting 0 or 1 here controls which one is used. + * + * Usually you want to set use_dummy_writes = 1. + * However, if that doesn't work or if you are using a slow SPI clock + * speed, you may want to use 0 here. */ + u16 use_dummy_writes; + + /* GPIO number to use as chip select */ + u16 gpio_cs; + + /* Board specific setup/teardown */ + int (*setup)(struct spi_device *spi); + int (*teardown)(struct spi_device *spi); +}; +#endif diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index 68bb1c5..a0faa18 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -204,6 +204,7 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv) * SPI slaves, and are numbered from zero to num_chipselects. * each slave has a chipselect signal, but it's common that not * every chipselect is connected to a slave. + * @dma_alignment: SPI controller constraint on DMA buffers alignment. * @setup: updates the device mode and clocking records used by a * device's SPI controller; protocol code may call this. This * must fail if an unrecognized or unsupported mode is requested. @@ -239,7 +240,17 @@ struct spi_master { */ u16 num_chipselect; - /* setup mode and clock, etc (spi driver may call many times) */ + /* some SPI controllers pose alignment requirements on DMAable + * buffers; let protocol drivers know about these requirements. + */ + u16 dma_alignment; + + /* Setup mode and clock, etc (spi driver may call many times). + * + * IMPORTANT: this may be called when transfers to another + * device are active. DO NOT UPDATE SHARED REGISTERS in ways + * which could break those transfers. + */ int (*setup)(struct spi_device *spi); /* bidirectional bulk transfers diff --git a/include/linux/spi/spi_gpio.h b/include/linux/spi/spi_gpio.h index 0f01a0f..ca6782e 100644 --- a/include/linux/spi/spi_gpio.h +++ b/include/linux/spi/spi_gpio.h @@ -25,10 +25,16 @@ * ... * }; * + * If chipselect is not used (there's only one device on the bus), assign + * SPI_GPIO_NO_CHIPSELECT to the controller_data: + * .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT; + * * If the bitbanged bus is later switched to a "native" controller, * that platform_device and controller_data should be removed. */ +#define SPI_GPIO_NO_CHIPSELECT ((unsigned long)-1l) + /** * struct spi_gpio_platform_data - parameter for bitbanged SPI master * @sck: number of the GPIO used for clock output |