From 1ce4da7a502ea637748bc55460fc43eb2acc4f01 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Mon, 7 Dec 2009 14:05:45 +0000 Subject: sh: MSIOF/mmc_spi platform data for the Ecovec24 board This patch adds MSIOF and mmc_spi platform data for the CN11 port on the SuperH Ecovec24 board. No card detect interrupt is available so the MMC code is configured to poll. The WP signal is implemented together with CD and power control. The board only supports 3.3V power. The platform data is wrapped in SDHI #ifdefs to allow both the SDHI and the MSIOF to coexist. Only one configuration is allowed at a time. The pin routing is selected by a dip switch but we can unfortunately not detect this setting at run time. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- arch/sh/boards/mach-ecovec24/setup.c | 97 +++++++++++++++++++++++++++++++++++- 1 file changed, 95 insertions(+), 2 deletions(-) (limited to 'arch/sh') diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c index 826e623..cfd958c 100644 --- a/arch/sh/boards/mach-ecovec24/setup.c +++ b/arch/sh/boards/mach-ecovec24/setup.c @@ -19,6 +19,10 @@ #include #include #include +#include +#include +#include +#include #include #include #include @@ -421,6 +425,7 @@ static struct i2c_board_info ts_i2c_clients = { .irq = IRQ0, }; +#ifdef CONFIG_MFD_SH_MOBILE_SDHI /* SHDI0 */ static void sdhi0_set_pwr(struct platform_device *pdev, int state) { @@ -493,6 +498,73 @@ static struct platform_device sdhi1_device = { }, }; +#else + +static int mmc_spi_get_ro(struct device *dev) +{ + return gpio_get_value(GPIO_PTY6); +} + +static int mmc_spi_get_cd(struct device *dev) +{ + return !gpio_get_value(GPIO_PTY7); +} + +static void mmc_spi_setpower(struct device *dev, unsigned int maskval) +{ + gpio_set_value(GPIO_PTB6, maskval ? 1 : 0); +} + +static struct mmc_spi_platform_data mmc_spi_info = { + .get_ro = mmc_spi_get_ro, + .get_cd = mmc_spi_get_cd, + .caps = MMC_CAP_NEEDS_POLL, + .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, /* 3.3V only */ + .setpower = mmc_spi_setpower, +}; + +static struct spi_board_info spi_bus[] = { + { + .modalias = "mmc_spi", + .platform_data = &mmc_spi_info, + .max_speed_hz = 5000000, + .mode = SPI_MODE_0, + .controller_data = (void *) GPIO_PTM4, + }, +}; + +static struct sh_msiof_spi_info msiof0_data = { + .num_chipselect = 1, +}; + +static struct resource msiof0_resources[] = { + [0] = { + .name = "MSIOF0", + .start = 0xa4c40000, + .end = 0xa4c40063, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = 84, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device msiof0_device = { + .name = "spi_sh_msiof", + .id = 0, /* MSIOF0 */ + .dev = { + .platform_data = &msiof0_data, + }, + .num_resources = ARRAY_SIZE(msiof0_resources), + .resource = msiof0_resources, + .archdata = { + .hwblk_id = HWBLK_MSIOF0, + }, +}; + +#endif + static struct platform_device *ecovec_devices[] __initdata = { &heartbeat_device, &nor_flash_device, @@ -503,8 +575,12 @@ static struct platform_device *ecovec_devices[] __initdata = { &ceu0_device, &ceu1_device, &keysc_device, +#ifdef CONFIG_MFD_SH_MOBILE_SDHI &sdhi0_device, &sdhi1_device, +#else + &msiof0_device, +#endif }; #define EEPROM_ADDR 0x50 @@ -773,7 +849,8 @@ static int __init arch_setup(void) gpio_direction_input(GPIO_PTR5); gpio_direction_input(GPIO_PTR6); - /* enable SDHI0 (needs DS2.4 set to ON) */ +#ifdef CONFIG_MFD_SH_MOBILE_SDHI + /* enable SDHI0 on CN11 (needs DS2.4 set to ON) */ gpio_request(GPIO_FN_SDHI0CD, NULL); gpio_request(GPIO_FN_SDHI0WP, NULL); gpio_request(GPIO_FN_SDHI0CMD, NULL); @@ -785,7 +862,7 @@ static int __init arch_setup(void) gpio_request(GPIO_PTB6, NULL); gpio_direction_output(GPIO_PTB6, 0); - /* enable SDHI1 (needs DS2.6,7 set to ON,OFF) */ + /* enable SDHI1 on CN12 (needs DS2.6,7 set to ON,OFF) */ gpio_request(GPIO_FN_SDHI1CD, NULL); gpio_request(GPIO_FN_SDHI1WP, NULL); gpio_request(GPIO_FN_SDHI1CMD, NULL); @@ -799,6 +876,22 @@ static int __init arch_setup(void) /* I/O buffer drive ability is high for SDHI1 */ ctrl_outw((ctrl_inw(IODRIVEA) & ~0x3000) | 0x2000 , IODRIVEA); +#else + /* enable MSIOF0 on CN11 (needs DS2.4 set to OFF) */ + gpio_request(GPIO_FN_MSIOF0_TXD, NULL); + gpio_request(GPIO_FN_MSIOF0_RXD, NULL); + gpio_request(GPIO_FN_MSIOF0_TSCK, NULL); + gpio_request(GPIO_PTM4, NULL); /* software CS control of TSYNC pin */ + gpio_direction_output(GPIO_PTM4, 1); /* active low CS */ + gpio_request(GPIO_PTB6, NULL); /* 3.3V power control */ + gpio_direction_output(GPIO_PTB6, 0); /* disable power by default */ + gpio_request(GPIO_PTY6, NULL); /* write protect */ + gpio_direction_input(GPIO_PTY6); + gpio_request(GPIO_PTY7, NULL); /* card detect */ + gpio_direction_input(GPIO_PTY7); + + spi_register_board_info(spi_bus, ARRAY_SIZE(spi_bus)); +#endif /* enable I2C device */ i2c_register_board_info(1, i2c1_devices, -- cgit v1.1