From 6ad601955315b010a117306b994f2204fae85fdc Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Fri, 15 Oct 2010 11:00:08 +0200 Subject: libahci: fix result_tf handling after an ATA PIO data-in command ATA devices don't send D2H Reg FIS after an successful ATA PIO data-in command. The host is supposed to take the TF and E_Status of the preceding PIO Setup FIS. Update ahci_qc_fill_rtf() such that it takes TF + E_Status from PIO Setup FIS after a successful ATA PIO data-in command. Without this patch, result_tf for such a command is filled with the content of the previous D2H Reg FIS which belongs to a previous command, which can make the command incorrectly seen as failed. * Patch updated to grab the whole TF + E_Status from PIO Setup FIS instead of just E_Status as suggested by Robert Hancock. Signed-off-by: Tejun Heo Reported-by: Mark Lord Cc: Robert Hancock Cc: stable@kernel.org Signed-off-by: Jeff Garzik --- drivers/ata/ahci.h | 1 + drivers/ata/libahci.c | 18 +++++++++++++++--- 2 files changed, 16 insertions(+), 3 deletions(-) (limited to 'drivers/ata') diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h index 1a2aacf..329cbbb 100644 --- a/drivers/ata/ahci.h +++ b/drivers/ata/ahci.h @@ -72,6 +72,7 @@ enum { AHCI_CMD_RESET = (1 << 8), AHCI_CMD_CLR_BUSY = (1 << 10), + RX_FIS_PIO_SETUP = 0x20, /* offset of PIO Setup FIS data */ RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */ RX_FIS_SDB = 0x58, /* offset of SDB FIS data */ RX_FIS_UNK = 0x60, /* offset of Unknown FIS data */ diff --git a/drivers/ata/libahci.c b/drivers/ata/libahci.c index 524dbe8..ebc08d6 100644 --- a/drivers/ata/libahci.c +++ b/drivers/ata/libahci.c @@ -1752,12 +1752,24 @@ static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc) static bool ahci_qc_fill_rtf(struct ata_queued_cmd *qc) { struct ahci_port_priv *pp = qc->ap->private_data; - u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG; + u8 *rx_fis = pp->rx_fis; if (pp->fbs_enabled) - d2h_fis += qc->dev->link->pmp * AHCI_RX_FIS_SZ; + rx_fis += qc->dev->link->pmp * AHCI_RX_FIS_SZ; + + /* + * After a successful execution of an ATA PIO data-in command, + * the device doesn't send D2H Reg FIS to update the TF and + * the host should take TF and E_Status from the preceding PIO + * Setup FIS. + */ + if (qc->tf.protocol == ATA_PROT_PIO && qc->dma_dir == DMA_FROM_DEVICE && + !(qc->flags & ATA_QCFLAG_FAILED)) { + ata_tf_from_fis(rx_fis + RX_FIS_PIO_SETUP, &qc->result_tf); + qc->result_tf.command = (rx_fis + RX_FIS_PIO_SETUP)[15]; + } else + ata_tf_from_fis(rx_fis + RX_FIS_D2H_REG, &qc->result_tf); - ata_tf_from_fis(d2h_fis, &qc->result_tf); return true; } -- cgit v1.1