diff options
Diffstat (limited to 'Documentation/ABI/testing')
| -rw-r--r-- | Documentation/ABI/testing/sysfs-ata | 99 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-devices-power | 88 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-driver-hid-roccat-pyra | 98 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-module | 12 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-power | 29 |
5 files changed, 326 insertions, 0 deletions
diff --git a/Documentation/ABI/testing/sysfs-ata b/Documentation/ABI/testing/sysfs-ata new file mode 100644 index 0000000..0a93215 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-ata @@ -0,0 +1,99 @@ +What: /sys/class/ata_... +Date: August 2008 +Contact: Gwendal Grignou<gwendal@google.com> +Description: + +Provide a place in sysfs for storing the ATA topology of the system. This allows +retrieving various information about ATA objects. + +Files under /sys/class/ata_port +------------------------------- + + For each port, a directory ataX is created where X is the ata_port_id of + the port. The device parent is the ata host device. + +idle_irq (read) + + Number of IRQ received by the port while idle [some ata HBA only]. + +nr_pmp_links (read) + + If a SATA Port Multiplier (PM) is connected, number of link behind it. + +Files under /sys/class/ata_link +------------------------------- + + Behind each port, there is a ata_link. If there is a SATA PM in the + topology, 15 ata_link objects are created. + + If a link is behind a port, the directory name is linkX, where X is + ata_port_id of the port. + If a link is behind a PM, its name is linkX.Y where X is ata_port_id + of the parent port and Y the PM port. + +hw_sata_spd_limit + + Maximum speed supported by the connected SATA device. + +sata_spd_limit + + Maximum speed imposed by libata. + +sata_spd + + Current speed of the link [1.5, 3Gps,...]. + +Files under /sys/class/ata_device +--------------------------------- + + Behind each link, up to two ata device are created. + The name of the directory is devX[.Y].Z where: + - X is ata_port_id of the port where the device is connected, + - Y the port of the PM if any, and + - Z the device id: for PATA, there is usually 2 devices [0,1], + only 1 for SATA. + +class + Device class. Can be "ata" for disk, "atapi" for packet device, + "pmp" for PM, or "none" if no device was found behind the link. + +dma_mode + + Transfer modes supported by the device when in DMA mode. + Mostly used by PATA device. + +pio_mode + + Transfer modes supported by the device when in PIO mode. + Mostly used by PATA device. + +xfer_mode + + Current transfer mode. + +id + + Cached result of IDENTIFY command, as described in ATA8 7.16 and 7.17. + Only valid if the device is not a PM. + +gscr + + Cached result of the dump of PM GSCR register. + Valid registers are: + 0: SATA_PMP_GSCR_PROD_ID, + 1: SATA_PMP_GSCR_REV, + 2: SATA_PMP_GSCR_PORT_INFO, + 32: SATA_PMP_GSCR_ERROR, + 33: SATA_PMP_GSCR_ERROR_EN, + 64: SATA_PMP_GSCR_FEAT, + 96: SATA_PMP_GSCR_FEAT_EN, + 130: SATA_PMP_GSCR_SII_GPIO + Only valid if the device is a PM. + +spdn_cnt + + Number of time libata decided to lower the speed of link due to errors. + +ering + + Formatted output of the error ring of the device. diff --git a/Documentation/ABI/testing/sysfs-devices-power b/Documentation/ABI/testing/sysfs-devices-power index 6123c52..7628cd1 100644 --- a/Documentation/ABI/testing/sysfs-devices-power +++ b/Documentation/ABI/testing/sysfs-devices-power @@ -77,3 +77,91 @@ Description: devices this attribute is set to "enabled" by bus type code or device drivers and in that cases it should be safe to leave the default value. + +What: /sys/devices/.../power/wakeup_count +Date: September 2010 +Contact: Rafael J. Wysocki <rjw@sisk.pl> +Description: + The /sys/devices/.../wakeup_count attribute contains the number + of signaled wakeup events associated with the device. This + attribute is read-only. If the device is not enabled to wake up + the system from sleep states, this attribute is empty. + +What: /sys/devices/.../power/wakeup_active_count +Date: September 2010 +Contact: Rafael J. Wysocki <rjw@sisk.pl> +Description: + The /sys/devices/.../wakeup_active_count attribute contains the + number of times the processing of wakeup events associated with + the device was completed (at the kernel level). This attribute + is read-only. If the device is not enabled to wake up the + system from sleep states, this attribute is empty. + +What: /sys/devices/.../power/wakeup_hit_count +Date: September 2010 +Contact: Rafael J. Wysocki <rjw@sisk.pl> +Description: + The /sys/devices/.../wakeup_hit_count attribute contains the + number of times the processing of a wakeup event associated with + the device might prevent the system from entering a sleep state. + This attribute is read-only. If the device is not enabled to + wake up the system from sleep states, this attribute is empty. + +What: /sys/devices/.../power/wakeup_active +Date: September 2010 +Contact: Rafael J. Wysocki <rjw@sisk.pl> +Description: + The /sys/devices/.../wakeup_active attribute contains either 1, + or 0, depending on whether or not a wakeup event associated with + the device is being processed (1). This attribute is read-only. + If the device is not enabled to wake up the system from sleep + states, this attribute is empty. + +What: /sys/devices/.../power/wakeup_total_time_ms +Date: September 2010 +Contact: Rafael J. Wysocki <rjw@sisk.pl> +Description: + The /sys/devices/.../wakeup_total_time_ms attribute contains + the total time of processing wakeup events associated with the + device, in milliseconds. This attribute is read-only. If the + device is not enabled to wake up the system from sleep states, + this attribute is empty. + +What: /sys/devices/.../power/wakeup_max_time_ms +Date: September 2010 +Contact: Rafael J. Wysocki <rjw@sisk.pl> +Description: + The /sys/devices/.../wakeup_max_time_ms attribute contains + the maximum time of processing a single wakeup event associated + with the device, in milliseconds. This attribute is read-only. + If the device is not enabled to wake up the system from sleep + states, this attribute is empty. + +What: /sys/devices/.../power/wakeup_last_time_ms +Date: September 2010 +Contact: Rafael J. Wysocki <rjw@sisk.pl> +Description: + The /sys/devices/.../wakeup_last_time_ms attribute contains + the value of the monotonic clock corresponding to the time of + signaling the last wakeup event associated with the device, in + milliseconds. This attribute is read-only. If the device is + not enabled to wake up the system from sleep states, this + attribute is empty. + +What: /sys/devices/.../power/autosuspend_delay_ms +Date: September 2010 +Contact: Alan Stern <stern@rowland.harvard.edu> +Description: + The /sys/devices/.../power/autosuspend_delay_ms attribute + contains the autosuspend delay value (in milliseconds). Some + drivers do not want their device to suspend as soon as it + becomes idle at run time; they want the device to remain + inactive for a certain minimum period of time first. That + period is called the autosuspend delay. Negative values will + prevent the device from being suspended at run time (similar + to writing "on" to the power/control attribute). Values >= + 1000 will cause the autosuspend timer expiration to be rounded + up to the nearest second. + + Not all drivers support this attribute. If it isn't supported, + attempts to read or write it will yield I/O errors. diff --git a/Documentation/ABI/testing/sysfs-driver-hid-roccat-pyra b/Documentation/ABI/testing/sysfs-driver-hid-roccat-pyra new file mode 100644 index 0000000..ad1125b --- /dev/null +++ b/Documentation/ABI/testing/sysfs-driver-hid-roccat-pyra @@ -0,0 +1,98 @@ +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/actual_cpi +Date: August 2010 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: It is possible to switch the cpi setting of the mouse with the + press of a button. + When read, this file returns the raw number of the actual cpi + setting reported by the mouse. This number has to be further + processed to receive the real dpi value. + + VALUE DPI + 1 400 + 2 800 + 4 1600 + + This file is readonly. + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/actual_profile +Date: August 2010 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When read, this file returns the number of the actual profile in + range 0-4. + This file is readonly. + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/firmware_version +Date: August 2010 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When read, this file returns the raw integer version number of the + firmware reported by the mouse. Using the integer value eases + further usage in other programs. To receive the real version + number the decimal point has to be shifted 2 positions to the + left. E.g. a returned value of 138 means 1.38 + This file is readonly. + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/profile_settings +Date: August 2010 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: The mouse can store 5 profiles which can be switched by the + press of a button. A profile is split in settings and buttons. + profile_settings holds informations like resolution, sensitivity + and light effects. + When written, this file lets one write the respective profile + settings back to the mouse. The data has to be 13 bytes long. + The mouse will reject invalid data. + Which profile to write is determined by the profile number + contained in the data. + This file is writeonly. + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/profile[1-5]_settings +Date: August 2010 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: The mouse can store 5 profiles which can be switched by the + press of a button. A profile is split in settings and buttons. + profile_settings holds informations like resolution, sensitivity + and light effects. + When read, these files return the respective profile settings. + The returned data is 13 bytes in size. + This file is readonly. + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/profile_buttons +Date: August 2010 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: The mouse can store 5 profiles which can be switched by the + press of a button. A profile is split in settings and buttons. + profile_buttons holds informations about button layout. + When written, this file lets one write the respective profile + buttons back to the mouse. The data has to be 19 bytes long. + The mouse will reject invalid data. + Which profile to write is determined by the profile number + contained in the data. + This file is writeonly. + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/profile[1-5]_buttons +Date: August 2010 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: The mouse can store 5 profiles which can be switched by the + press of a button. A profile is split in settings and buttons. + profile_buttons holds informations about button layout. + When read, these files return the respective profile buttons. + The returned data is 19 bytes in size. + This file is readonly. + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/startup_profile +Date: August 2010 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: The integer value of this attribute ranges from 0-4. + When read, this attribute returns the number of the profile + that's active when the mouse is powered on. + This file is readonly. + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/settings +Date: August 2010 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When read, this file returns the settings stored in the mouse. + The size of the data is 3 bytes and holds information on the + startup_profile. + When written, this file lets write settings back to the mouse. + The data has to be 3 bytes long. The mouse will reject invalid + data. diff --git a/Documentation/ABI/testing/sysfs-module b/Documentation/ABI/testing/sysfs-module new file mode 100644 index 0000000..cfcec3b --- /dev/null +++ b/Documentation/ABI/testing/sysfs-module @@ -0,0 +1,12 @@ +What: /sys/module/pch_phub/drivers/.../pch_mac +Date: August 2010 +KernelVersion: 2.6.35 +Contact: masa-korg@dsn.okisemi.com +Description: Write/read GbE MAC address. + +What: /sys/module/pch_phub/drivers/.../pch_firmware +Date: August 2010 +KernelVersion: 2.6.35 +Contact: masa-korg@dsn.okisemi.com +Description: Write/read Option ROM data. + diff --git a/Documentation/ABI/testing/sysfs-power b/Documentation/ABI/testing/sysfs-power index 2875f1f..194ca44 100644 --- a/Documentation/ABI/testing/sysfs-power +++ b/Documentation/ABI/testing/sysfs-power @@ -99,9 +99,38 @@ Description: dmesg -s 1000000 | grep 'hash matches' + If you do not get any matches (or they appear to be false + positives), it is possible that the last PM event point + referred to a device created by a loadable kernel module. In + this case cat /sys/power/pm_trace_dev_match (see below) after + your system is started up and the kernel modules are loaded. + CAUTION: Using it will cause your machine's real-time (CMOS) clock to be set to a random invalid time after a resume. +What; /sys/power/pm_trace_dev_match +Date: October 2010 +Contact: James Hogan <james@albanarts.com> +Description: + The /sys/power/pm_trace_dev_match file contains the name of the + device associated with the last PM event point saved in the RTC + across reboots when pm_trace has been used. More precisely it + contains the list of current devices (including those + registered by loadable kernel modules since boot) which match + the device hash in the RTC at boot, with a newline after each + one. + + The advantage of this file over the hash matches printed to the + kernel log (see /sys/power/pm_trace), is that it includes + devices created after boot by loadable kernel modules. + + Due to the small hash size necessary to fit in the RTC, it is + possible that more than one device matches the hash, in which + case further investigation is required to determine which + device is causing the problem. Note that genuine RTC clock + values (such as when pm_trace has not been used), can still + match a device and output it's name here. + What: /sys/power/pm_async Date: January 2009 Contact: Rafael J. Wysocki <rjw@sisk.pl> |