aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* f2fs: fix f2fs_write_meta_page at no checkpoint statusJaegeuk Kim2016-06-052-8/+23
| | | | | | | | | If f2fs entered errorneous checkpoint status, it should skip writing meta pages instead of redirtying the pages out. Otherwise, it cannot unmount the partition even though f2fs is under read-only status. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: fix to truncate dentry pages in the error caseJaegeuk Kim2016-06-051-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When a new directory is allocated, if an error is occurred, we should truncate preallocated dentry pages too. This bug was reported by Andrey Tsyvarev after a while as follows. mkdir()-> f2fs_add_link()-> init_inode_metadata()-> f2fs_init_acl()-> f2fs_get_acl()-> f2fs_getxattr()-> read_all_xattrs() fails. Also there was a BUG_ON triggered after the fault in mkdir()-> f2fs_add_link()-> init_inode_metadata()-> remove_inode_page() -> f2fs_bug_on(inode->i_blocks != 0 && inode->i_blocks != 1); But, previous patch wasn't perfect to resolve that bug, so the following bug report was also submitted. kernel BUG at fs/f2fs/inode.c:274! Call Trace: [<ffffffff811fde03>] evict+0xa3/0x1a0 [<ffffffff811fe615>] iput+0xf5/0x180 [<ffffffffa01c7f63>] f2fs_mkdir+0xf3/0x150 [f2fs] [<ffffffff811f2a77>] vfs_mkdir+0xb7/0x160 [<ffffffff811f36bf>] SyS_mkdir+0x5f/0xc0 [<ffffffff81680769>] system_call_fastpath+0x16/0x1b Finally, this patch resolves all the issues like below. If an error is occurred after make_empty_dir(), 1. truncate_inode_pages() The make_bad_inode() prior to iput() will change i_mode to S_IFREG, which means that f2fs will not decrement fi->dirty_dents during f2fs_evict_inode. But, by calling it here, we can do that. 2. truncate_blocks() Preallocated dentry pages are trucated here to sync i_blocks. 3. remove_dirty_dir_inode() Remove this directory inode from the list. Reported-and-Tested-by: Andrey Tsyvarev <tsyvarev@ispras.ru> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: fix a build warningJaegeuk Kim2016-06-051-11/+8
| | | | | | | | | | | | This patch modifies flow a little bit to avoid the following build warnings. src/fs/f2fs/recovery.c: In function ‘check_index_in_prev_nodes’: src/fs/f2fs/recovery.c:288:51: warning: ‘sum.<U5390>.<U52f8>.ofs_in_node’ may be used uninitialized in this function [-Wmaybe-uninitialized] src/fs/f2fs/recovery.c:260:23: warning: ‘sum.nid’ may be used uninitialized in this function [-Wmaybe-uninitialized] Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: clean up with a macroJaegeuk Kim2016-06-053-9/+8
| | | | | | This patch adds GET_BLKOFF_FROM_SEG0 to clean up some codes. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: fix the potential mismatch between dir's i_size and i_blocksJaegeuk Kim2016-06-051-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | This is the erroneous scenario. i_size on-disk i_size i_blocks __f2fs_add_link() 4096 4096 2 get_new_data_page 8192 4096 3 -ENOSPC = init_inode_metadata checkpoint - 4096 3 POR and reboot __f2fs_add_link() 4096 4096 3 page = get_new_data_page (page->index = 1 by NEW_ADDR) add a dentry to the page successfully f2fs_rmdir() f2fs_empty_dir() 4096 4096 3 f2fs_unlink() goes, since there is no valid dentry due to i_size = 4096. But, still there is one dentry in page->index = 1. So this patch moves the code to write dir->i_size into on-disk i_size in order to sync dir's i_size, on-disk i_size, and its i_blocks. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: remove the ugly pointer conversionJaegeuk Kim2016-06-052-4/+8
| | | | | | | | | | | | | This patch modifies the use of bi_private to remove pointer chasing for sbi. Previously, we had a bi_private structure, but it needs memory allocation. So this patch uses bi_private by the sbi pointer and adds a completion pointer into the sbi. This can achieve no memory allocation and nice use of the bi_private. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com> Conflicts: fs/f2fs/data.c
* f2fs: fix to recover xattr node blockJaegeuk Kim2016-06-053-0/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If a new xattr node page was allocated and its inode is fsynced, we should recover the xattr node page during the roll-forward process after power-cut. But, previously, f2fs didn't handle that case, resulting in kernel panic as follows reported by Tom Li. BUG: unable to handle kernel paging request at ffffc9001c861a98 IP: [<ffffffffa0295236>] check_index_in_prev_nodes+0x86/0x2d0 [f2fs] Call Trace: [<ffffffff815ece9b>] ? printk+0x48/0x4a [<ffffffffa029626a>] recover_fsync_data+0xdca/0xf50 [f2fs] [<ffffffffa02873ae>] f2fs_fill_super+0x92e/0x970 [f2fs] [<ffffffff8112c9f8>] mount_bdev+0x1b8/0x200 [<ffffffffa0286a80>] ? f2fs_remount+0x130/0x130 [f2fs] [<ffffffffa0285e40>] f2fs_mount+0x10/0x20 [f2fs] [<ffffffff8112d4de>] mount_fs+0x3e/0x1b0 [<ffffffff810ef4eb>] ? __alloc_percpu+0xb/0x10 [<ffffffff8114761f>] vfs_kern_mount+0x6f/0x120 [<ffffffff811497b9>] do_mount+0x259/0xa90 [<ffffffff810ead1d>] ? memdup_user+0x3d/0x80 [<ffffffff810eadb3>] ? strndup_user+0x53/0x70 [<ffffffff8114a2c9>] SyS_mount+0x89/0xd0 [<ffffffff815feae2>] system_call_fastpath+0x16/0x1b This patch adds a recovery function of xattr node pages. Reported-by: Tom Li <biergaizi@members.fsf.org> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: handle dirty segments inside refresh_sit_entryJaegeuk Kim2016-06-052-14/+11
| | | | | | This patch cleans up the refresh_sit_entry to handle locate_dirty_segments. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: update_inode_page should be done all the timeJaegeuk Kim2016-06-053-12/+22
| | | | | | | | | | | In order to make fs consistency, update_inode_page should not be failed all the time. Otherwise, it is possible to lose some metadata in the inode like a link count. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com> Conflicts: fs/f2fs/f2fs.h
* f2fs: backport k3.0 re-add start/end params to f2fs_sync_fileHashcode2016-06-052-2/+7
| | | | Change-Id: I47df9dba3a37eae26d4d7bec9ed4700b14ea7f84
* fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlersJosef Bacik2016-06-0571-167/+463
| | | | | | | | | | | | | | | | | | | | Btrfs needs to be able to control how filemap_write_and_wait_range() is called in fsync to make it less of a painful operation, so push down taking i_mutex and the calling of filemap_write_and_wait() down into the ->fsync() handlers. Some file systems can drop taking the i_mutex altogether it seems, like ext3 and ocfs2. For correctness sake I just pushed everything down in all cases to make sure that we keep the current behavior the same for everybody, and then each individual fs maintainer can make up their mind about what to do from there. Thanks, Acked-by: Jan Kara <jack@suse.cz> Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Conflicts: Documentation/filesystems/porting Change-Id: I7697244cce355e6d443a39c5133a5c94f02e199b
* f2fs: fix k3.0 merge by removing extra balance_fs and checkHashcode2016-06-051-5/+0
| | | | Change-Id: Icef3c6623a730d933071b7f600d758403fc64f16
* f2fs: drop obsolete node page when it is truncatedJaegeuk Kim2016-06-051-0/+4
| | | | | | | If a node page is trucated, we'd better drop the page in the node_inode's page cache for better memory footprint. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: introduce NODE_MAPPING for code consistencyJaegeuk Kim2016-06-054-31/+30
| | | | | | | | This patch adds NODE_MAPPING which is similar as META_MAPPING introduced by Gu Zheng. Cc: Gu Zheng <guz.fnst@cn.fujitsu.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: remove the orphan block page arrayGu Zheng2016-06-051-3/+4
| | | | | | | | | | | | | As the orphan_blocks may be max to 504, so it is not security and rigorous to store such a large array in the kernel stack as Dan Carpenter said. In fact, grab_meta_page has locked the page in the page cache, and we can use find_get_page() to fetch the page safely in the downstream, so we can remove the page array directly. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: add help function META_MAPPINGGu Zheng2016-06-055-8/+13
| | | | | | | | Introduce help function META_MAPPING() to get the cache meta blocks' address space. Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: move a branch for code redabilityJaegeuk Kim2016-06-051-5/+4
| | | | | | This patch moves a function in f2fs_delete_entry for code readability. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: call mark_inode_dirty to flush dirty pagesJaegeuk Kim2016-06-053-5/+8
| | | | | | | | If a dentry page is updated, we should call mark_inode_dirty to add the inode into the dirty list, so that its dentry pages are flushed to the disk. Otherwise, the inode can be evicted without flush. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: clean checkpatch warningsChris Fries2016-06-0511-30/+40
| | | | | | | | Fixed a variety of trivial checkpatch warnings. The only delta should be some minor formatting on log strings that were split / too long. Signed-off-by: Chris Fries <cfries@motorola.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: missing REQ_META and REQ_PRIO when sync_meta_pages(META_FLUSH)Changman Lee2016-06-051-1/+1
| | | | | | | | | Doing sync_meta_pages with META_FLUSH when checkpoint, we overide rw using WRITE_FLUSH_FUA. At this time, we also should set REQ_META|REQ_PRIO. Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: avoid f2fs_balance_fs call during pageoutJaegeuk Kim2016-06-051-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch should resolve the following bug. ========================================================= [ INFO: possible irq lock inversion dependency detected ] 3.13.0-rc5.f2fs+ #6 Not tainted --------------------------------------------------------- kswapd0/41 just changed the state of lock: (&sbi->gc_mutex){+.+.-.}, at: [<ffffffffa030503e>] f2fs_balance_fs+0xae/0xd0 [f2fs] but this lock took another, RECLAIM_FS-READ-unsafe lock in the past: (&sbi->cp_rwsem){++++.?} and interrupts could create inverse lock ordering between them. other info that might help us debug this: Chain exists of: &sbi->gc_mutex --> &sbi->cp_mutex --> &sbi->cp_rwsem Possible interrupt unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&sbi->cp_rwsem); local_irq_disable(); lock(&sbi->gc_mutex); lock(&sbi->cp_mutex); <Interrupt> lock(&sbi->gc_mutex); *** DEADLOCK *** This bug is due to the f2fs_balance_fs call in f2fs_write_data_page. If f2fs_write_data_page is triggered by wbc->for_reclaim via kswapd, it should not call f2fs_balance_fs which tries to get a mutex grabbed by original syscall flow. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: add delimiter to seperate name and value in debug phraseChangman Lee2016-06-051-4/+4
| | | | | | | | Support for f2fs-tools/tools/f2stat to monitor /sys/kernel/debug/f2fs/status Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: use spinlock rather than mutex for better speedGu Zheng2016-06-052-13/+13
| | | | | | | | | With the 2 previous changes, all the long time operations are moved out of the protection region, so here we can use spinlock rather than mutex (orphan_inode_mutex) for lower overhead. Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: move alloc new orphan node out of lock protection regionGu Zheng2016-06-051-6/+9
| | | | | | | Move alloc new orphan node out of lock protection region. Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: move grabing orphan pages out of protection regionGu Zheng2016-06-051-7/+9
| | | | | | | | | | Move grabing orphan block page out of protection region, and grab all the orphan block pages ahead. Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Reviewed-by: Chao Yu <chao2.yu@samsung.com> [Jaegeuk Kim: remove unnecessary code pointed by Chao Yu] Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: remove the needless parameter of f2fs_wait_on_page_writebackYuan Zhong2016-06-056-7/+7
| | | | | | | | "boo sync" parameter is never referenced in f2fs_wait_on_page_writeback. We should remove this parameter. Signed-off-by: Yuan Zhong <yuan.mark.zhong@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: add a sysfs entry to control max_victim_searchJaegeuk Kim2016-06-054-3/+12
| | | | | | | | | | | | | | | | | | | | | | Previously during SSR and GC, the maximum number of retrials to find a victim segment was hard-coded by MAX_VICTIM_SEARCH, 4096 by default. This number makes an effect on IO locality, when SSR mode is activated, which results in performance fluctuation on some low-end devices. If max_victim_search = 4, the victim will be searched like below. ("D" represents a dirty segment, and "*" indicates a selected victim segment.) D1 D2 D3 D4 D5 D6 D7 D8 D9 [ * ] [ * ] [ * ] [ ....] This patch adds a sysfs entry to control the number dynamically through: /sys/fs/f2fs/$dev/max_victim_search Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: improve write performance under frequent fsync callsJaegeuk Kim2016-06-054-10/+11
| | | | | | | | | | | | | | | | | | | | | | When considering a bunch of data writes with very frequent fsync calls, we are able to think the following performance regression. N: Node IO, D: Data IO, IO scheduler: cfq Issue pending IOs D1 D2 D3 D4 D1 D2 D3 D4 N1 D2 D3 D4 N1 N2 N1 D3 D4 N2 D1 --> N1 can be selected by cfq becase of the same priority of N and D. Then D3 and D4 would be delayed, resuling in performance degradation. So, when processing the fsync call, it'd better give higher priority to data IOs than node IOs by assigning WRITE and WRITE_SYNC respectively. This patch improves the random wirte performance with frequent fsync calls by up to 10%. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: avoid to read inline data except first pageChao Yu2016-06-051-0/+6
| | | | | | | | | | | | | | | | | | | | | | Here is a case which could read inline page data not from first page. 1. write inline data 2. lseek to offset 4096 3. read 4096 bytes from offset 4096 (read_inline_data read inline data page to non-first page, And previously VFS has add this page to page cache) 4. ftruncate offset 8192 5. read 4096 bytes from offset 4096 (we meet this updated page with inline data in cache) So we should leave this page with inited data and uptodate flag for this case. Change log from v1: o fix a deadlock bug Signed-off-by: Chao Yu <chao2.yu@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: avoid to left uninitialized data in page when read inline dataChao Yu2016-06-051-3/+2
| | | | | | | | | | | | | | | | | Change log from v1: o reduce unneeded memset in __f2fs_convert_inline_data >From 58796be2bd2becbe8d52305210fb2a64e7dd80b6 Mon Sep 17 00:00:00 2001 From: Chao Yu <chao2.yu@samsung.com> Date: Mon, 30 Dec 2013 09:21:33 +0800 Subject: [PATCH] f2fs: avoid to left uninitialized data in page when read inline data We left uninitialized data in the tail of page when we read an inline data page. So let's initialize left part of the page excluding inline data region. Signed-off-by: Chao Yu <chao2.yu@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: fix truncate_partial_nodes bugshifei10.ge2016-06-051-6/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The truncate_partial_nodes puts pages incorrectly in the following two cases. Note that the value for argc 'depth' can only be 2 or 3. Please see truncate_inode_blocks() and truncate_partial_nodes(). 1) An err is occurred in the first 'for' loop When err is occurred with depth = 2, pages[0] is invalid, so this page doesn't need to be put. There is no problem, however, when depth is 3, it doesn't put the pages correctly where pages[0] is valid and pages[1] is invalid. In this case, depth is set to 2 (ref to statemnt depth = i + 1), and then 'goto fail'. In label 'fail', for (i = depth - 3; i >= 0; i--) cannot meet the condition because i = -1, so pages[0] cann't be put. 2) An err happened in the second 'for' loop Now we've got pages[0] with depth = 2, or we've got pages[0] and pages[1] with depth = 3. When an err is detected, we need 'goto fail' to put such the pages. When depth is 2, in label 'fail', for (i = depth - 3; i >= 0; i--) cann't meet the condition because i = -1, so pages[0] cann't be put. When depth is 3, in label 'fail', for (i = depth - 3; i >= 0; i--) can only put pages[0], pages[1] also cann't be put. Note that 'depth' has been changed before first 'goto fail' (ref to statemnt depth = i + 1), so passing this modified 'depth' to the tracepoint, trace_f2fs_truncate_partial_nodes, is also incorrect. Signed-off-by: Shifei Ge <shifei10.ge@samsung.com> [Jaegeuk Kim: modify the description and fix one bug] Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: handle errors correctly during f2fs_reserve_blockJaegeuk Kim2016-06-053-16/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The get_dnode_of_data nullifies inode and node page when error is occurred. There are two cases that passes inode page into get_dnode_of_data(). 1. make_empty_dir() -> get_new_data_page() -> f2fs_reserve_block(ipage) -> get_dnode_of_data() 2. f2fs_convert_inline_data() -> __f2fs_convert_inline_data() -> f2fs_reserve_block(ipage) -> get_dnode_of_data() This patch adds correct error handling codes when get_dnode_of_data() returns an error. At first, f2fs_reserve_block() calls f2fs_put_dnode() whenever reserve_new_block returns an error. So, the rule of f2fs_reserve_block() is to nullify inode page when there is any error internally. Finally, two callers of f2fs_reserve_block() should call f2fs_put_dnode() appropriately if they got an error since successful f2fs_reserve_block(). Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: add inline_data recovery routineJaegeuk Kim2016-06-055-5/+58
| | | | | | | | | | | | This patch adds a inline_data recovery routine with the following policy. [prev.] [next] of inline_data flag o o -> recover inline_data o x -> remove inline_data, and then recover data blocks x o -> remove inline_data, and then recover inline_data x x -> recover data blocks Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: add the number of inline_data files to status infoJaegeuk Kim2016-06-054-7/+26
| | | | | | | This patch adds the number of inline_data files into the status information. Note that the number is reset whenever the filesystem is newly mounted. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: refactor f2fs_convert_inline_dataJaegeuk Kim2016-06-054-41/+28
| | | | | | | | | | | | | | | | | Change log from v1: o handle NULL pointer of grab_cache_page_write_begin() pointed by Chao Yu. This patch refactors f2fs_convert_inline_data to check a couple of conditions internally for deciding whether it needs to convert inline_data or not. So, the new f2fs_convert_inline_data initially checks: 1) f2fs_has_inline_data(), and 2) the data size to be changed. If the inode has inline_data but the size to fill is less than MAX_INLINE_DATA, then we don't need to convert the inline_data with data allocation. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: call f2fs_put_page at the error caseJaegeuk Kim2016-06-051-1/+3
| | | | | | | | | | | | | | | | | | | | | | | In f2fs_write_begin(), if f2fs_conver_inline_data() returns an error like -ENOSPC, f2fs should call f2fs_put_page(). Otherwise, it is remained as a locked page, resulting in the following bug. [<ffffffff8114657e>] sleep_on_page+0xe/0x20 [<ffffffff81146567>] __lock_page+0x67/0x70 [<ffffffff81157d08>] truncate_inode_pages_range+0x368/0x5d0 [<ffffffff81157ff5>] truncate_inode_pages+0x15/0x20 [<ffffffff8115804b>] truncate_pagecache+0x4b/0x70 [<ffffffff81158082>] truncate_setsize+0x12/0x20 [<ffffffffa02a1842>] f2fs_setattr+0x72/0x270 [f2fs] [<ffffffff811cdae3>] notify_change+0x213/0x400 [<ffffffff811ab376>] do_truncate+0x66/0xa0 [<ffffffff811ab541>] vfs_truncate+0x191/0x1b0 [<ffffffff811ab5bc>] do_sys_truncate+0x5c/0xa0 [<ffffffff811ab78e>] SyS_truncate+0xe/0x10 [<ffffffff81756052>] system_call_fastpath+0x16/0x1b [<ffffffffffffffff>] 0xffffffffffffffff Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: convert inline_data for punch_holeJaegeuk Kim2016-06-051-19/+3
| | | | | | | | | In the punch_hole(), let's convert inline_data all the time for simplicity and to avoid potential deadlock conditions. It is pretty much not a big deal to do this. Reviewed-by: Chao Yu <chao2.yu@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: don't need to get f2fs_lock_op for the inline_data testJaegeuk Kim2016-06-051-5/+4
| | | | | | | This patch locates checking the inline_data prior to calling f2fs_lock_op() in truncate_blocks(), since getting the lock is unnecessary. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: handle inline data operationsHuajun Li2016-06-052-8/+86
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hook inline data read/write, truncate, fallocate, setattr, etc. Files need meet following 2 requirement to inline: 1) file size is not greater than MAX_INLINE_DATA; 2) file doesn't pre-allocate data blocks by fallocate(). FI_INLINE_DATA will not be set while creating a new regular inode because most of the files are bigger than ~3.4K. Set FI_INLINE_DATA only when data is submitted to block layer, ranther than set it while creating a new inode, this also avoids converting data from inline to normal data block and vice versa. While writting inline data to inode block, the first data block should be released if the file has a block indexed by i_addr[0]. On the other hand, when a file operation is appied to a file with inline data, we need to test if this file can remain inline by doing this operation, otherwise it should be convert into normal file by reserving a new data block, copying inline data to this new block and clear FI_INLINE_DATA flag. Because reserve a new data block here will make use of i_addr[0], if we save inline data in i_addr[0..872], then the first 4 bytes would be overwriten. This problem can be avoided simply by not using i_addr[0] for inline data. Signed-off-by: Huajun Li <huajun.li@intel.com> Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com> Signed-off-by: Weihong Xu <weihong.xu@intel.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: key functions to handle inline dataHuajun Li2016-06-053-1/+185
| | | | | | | | | | Functions to implement inline data read/write, and move inline data to normal data block when file size exceeds inline data limitation. Signed-off-by: Huajun Li <huajun.li@intel.com> Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com> Signed-off-by: Weihong Xu <weihong.xu@intel.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: convert max_orphans to a field of f2fs_sb_infoGu Zheng2016-06-052-10/+11
| | | | | | | | | | Previously, we need to calculate the max orphan num when we try to acquire an orphan inode, but it's a stable value since the super block was inited. So converting it to a field of f2fs_sb_info and use it directly when needed seems a better choose. Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: check the blocksize before calling generic_direct_IO pathJaegeuk Kim2016-06-051-0/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The f2fs supports 4KB block size. If user requests dwrite with under 4KB data, it allocates a new 4KB data block. However, f2fs doesn't add zero data into the untouched data area inside the newly allocated data block. This incurs an error during the xfstest #263 test as follow. 263 12s ... [failed, exit status 1] - output mismatch (see 263.out.bad) --- 263.out 2013-03-09 03:37:15.043967603 +0900 +++ 263.out.bad 2013-12-27 04:20:39.230203114 +0900 @@ -1,3 +1,976 @@ QA output created by 263 fsx -N 10000 -o 8192 -l 500000 -r PSIZE -t BSIZE -w BSIZE -Z -fsx -N 10000 -o 128000 -l 500000 -r PSIZE -t BSIZE -w BSIZE -Z +fsx -N 10000 -o 8192 -l 500000 -r PSIZE -t BSIZE -w BSIZE -Z +truncating to largest ever: 0x12a00 +truncating to largest ever: 0x75400 +fallocating to largest ever: 0x79cbf ... (Run 'diff -u 263.out 263.out.bad' to see the entire diff) Ran: 263 Failures: 263 Failed 1 of 1 tests It turns out that, when the test tries to write 2KB data with dio, the new dio path allocates 4KB data block without filling zero data inside the remained 2KB area. Finally, the output file contains a garbage data for that region. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com> Conflicts: fs/f2fs/data.c Change-Id: Icb257bb0f9c2cf33f0534d529aa65cbf9a0bbbd4
* f2fs: should put the dnode when NEW_ADDR is detectedJaegeuk Kim2016-06-051-2/+7
| | | | | | | | | | | When get_dnode_of_data() in get_data_block() returns a successful dnode, we should put the dnode. But, previously, if its data block address is equal to NEW_ADDR, we didn't do that, resulting in a deadlock condition. So, this patch splits original error conditions with this case, and then calls f2fs_put_dnode before finishing the function. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: introduce F2FS_INODE macro to get f2fs_inodeJaegeuk Kim2016-06-055-29/+28
| | | | | | | | | | | | This patch introduces F2FS_INODE that returns struct f2fs_inode * from the inode page. By using this macro, we can remove unnecessary casting codes like below. struct f2fs_inode *ri = &F2FS_NODE(inode_page)->i; -> struct f2fs_inode *ri = F2FS_INODE(inode_page); Reviewed-by: Chao Yu <chao2.yu@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: check filename length in recover_dentryChao Yu2016-06-052-3/+6
| | | | | | | | | | | | | | | | | In current flow, we will get Null return value of f2fs_find_entry in recover_dentry when name.len is bigger than F2FS_NAME_LEN, and then we still add this inode into its dir entry. To avoid this situation, we must check filename length before we use it. Another point is that we could remove the code of checking filename length In f2fs_find_entry, because f2fs_lookup will be called previously to ensure of validity of filename length. V2: o add WARN_ON() as Jaegeuk Kim suggested. Signed-off-by: Chao Yu <chao2.yu@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: avoid to set wrong pino of inode when rename dirChao Yu2016-06-052-3/+2
| | | | | | | | | | | | When we rename a dir to new name which is not exist previous, we will set pino of parent inode with ino of child inode in f2fs_set_link. It destroy consistency of pino, it should be fixed. Thanks for previous work of Shu Tan. Signed-off-by: Shu Tan <shu.tan@samsung.com> Signed-off-by: Chao Yu <chao2.yu@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: update several commentsChao Yu2016-06-055-14/+22
| | | | | | | | | | Update several comments: 1. use f2fs_{un}lock_op install of mutex_{un}lock_op. 2. update comment of get_data_block(). 3. update description of node offset. Signed-off-by: Chao Yu <chao2.yu@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: remove the rw_flag domain from f2fs_io_infoGu Zheng2016-06-055-16/+7
| | | | | | | | | | | | When using the f2fs_io_info in the low level, we still need to merge the rw and rw_flag, so use the rw to hold all the io flags directly, and remove the rw_flag field. ps.It is based on the previous patch: f2fs: move all the bio initialization into __bio_alloc Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: move all the bio initialization into __bio_allocGu Zheng2016-06-051-50/+42
| | | | | | | | | | | | | | | Move all the bio initialization into __bio_alloc, and some minor cleanups are also added. v3: Use 'bool' rather than 'int' as Kim suggested. v2: Use 'is_read' rather than 'rw' as Yu Chao suggested. Remove the needless initialization of bio->bi_private. Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
* f2fs: write dirty meta pages collectivelyJaegeuk Kim2016-06-051-3/+4
| | | | | | | | | This patch enhances writing dirty meta pages collectively in background. During the file data writes, it'd better avoid to write small dirty meta pages frequently. So let's give a chance to collect a number of dirty meta pages for a while. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
generated by cgit v1.1 at 2024-10-27 22:59:19 +0000