| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
| |
The rcu callback xps_dev_maps_release() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(xps_dev_maps_release).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
|
|
|
|
|
|
|
|
|
|
| |
The rcu callback xps_map_release() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(xps_map_release).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
|
|
|
|
|
|
|
|
|
|
| |
The rcu callback rps_map_release() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(rps_map_release).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
commit a512b92 adds sysfs entry for net device group, but
before this commit, tun also uses group sysfs, so after this
commit checkin, kernel warns like this:
sysfs: cannot create duplicate filename '/devices/virtual/net/vnet0/group'
Since tun has used this for years, rename sysfs under tun might
break existing userspace, so rename group sysfs entry for net device
group is a better choice.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The group of a network device can be queried or changed from userspace
using sysfs.
For example, considering sysfs mounted in /sys, one can change the group
that interface lo belongs to:
echo 1 > /sys/class/net/lo/group
Signed-off-by: Vlad Dogaru <ddvlad@rosedu.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Quoting Ben Hutchings: we presumably won't be defining features that
can only be enabled on 64-bit architectures.
Occurences found by `grep -r` on net/, drivers/net, include/
[ Move features and vlan_features next to each other in
struct netdev, as per Eric Dumazet's suggestion -DaveM ]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
| |
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Allocate qdisc memory according to NUMA properties of cpus included in
xps map.
To be effective, qdisc should be (re)setup after changes
of /sys/class/net/eth<n>/queues/tx-<n>/xps_cpus
I added a numa_node field in struct netdev_queue, containing NUMA node
if all cpus included in xps_cpus share same node, else -1.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
Avoid sparse warnings : add __rcu annotations and use
rcu_dereference_protected() where necessary.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
store_xps_map() allocates maps that are used by single cpu, it makes
sense to use NUMA allocations.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
This patch adds XPS_CONFIG option to enable and disable XPS. This is
done in the same manner as RPS_CONFIG. This is also fixes build
failure in XPS code when SMP is not enabled.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch implements transmit packet steering (XPS) for multiqueue
devices. XPS selects a transmit queue during packet transmission based
on configuration. This is done by mapping the CPU transmitting the
packet to a queue. This is the transmit side analogue to RPS-- where
RPS is selecting a CPU based on receive queue, XPS selects a queue
based on the CPU (previously there was an XPS patch from Eric
Dumazet, but that might more appropriately be called transmit completion
steering).
Each transmit queue can be associated with a number of CPUs which will
use the queue to send packets. This is configured as a CPU mask on a
per queue basis in:
/sys/class/net/eth<n>/queues/tx-<n>/xps_cpus
The mappings are stored per device in an inverted data structure that
maps CPUs to queues. In the netdevice structure this is an array of
num_possible_cpu structures where each structure holds and array of
queue_indexes for queues which that CPU can use.
The benefits of XPS are improved locality in the per queue data
structures. Also, transmit completions are more likely to be done
nearer to the sending thread, so this should promote locality back
to the socket on free (e.g. UDP). The benefits of XPS are dependent on
cache hierarchy, application load, and other factors. XPS would
nominally be configured so that a queue would only be shared by CPUs
which are sharing a cache, the degenerative configuration woud be that
each CPU has it's own queue.
Below are some benchmark results which show the potential benfit of
this patch. The netperf test has 500 instances of netperf TCP_RR test
with 1 byte req. and resp.
bnx2x on 16 core AMD
XPS (16 queues, 1 TX queue per CPU) 1234K at 100% CPU
No XPS (16 queues) 996K at 100% CPU
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
netif_set_real_num_rx_queues() can decrement and increment
the number of rx queues. For example ixgbe does this as
features and offloads are toggled. Presumably this could
also happen across down/up on most devices if the available
resources changed (cpu offlined).
The kobject needs to be zero'd in this case so that the
state is not preserved across kobject_put()/kobject_init_and_add().
This resolves the following error report.
ixgbe 0000:03:00.0: eth2: NIC Link is Up 10 Gbps, Flow Control: RX/TX
kobject (ffff880324b83210): tried to init an initialized object, something is seriously wrong.
Pid: 1972, comm: lldpad Not tainted 2.6.37-rc18021qaz+ #169
Call Trace:
[<ffffffff8121c940>] kobject_init+0x3a/0x83
[<ffffffff8121cf77>] kobject_init_and_add+0x23/0x57
[<ffffffff8107b800>] ? mark_lock+0x21/0x267
[<ffffffff813c6d11>] net_rx_queue_update_kobjects+0x63/0xc6
[<ffffffff813b5e0e>] netif_set_real_num_rx_queues+0x5f/0x78
[<ffffffffa0261d49>] ixgbe_set_num_queues+0x1c6/0x1ca [ixgbe]
[<ffffffffa0262509>] ixgbe_init_interrupt_scheme+0x1e/0x79c [ixgbe]
[<ffffffffa0274596>] ixgbe_dcbnl_set_state+0x167/0x189 [ixgbe]
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
This patch move RX queue allocation to alloc_netdev_mq and freeing of
the queues to free_netdev (symmetric to TX queue allocation). Each
kobject RX queue takes a reference to the queue's device so that the
device can't be freed before all the kobjects have been released-- this
obviates the need for reference counts specific to RX queues.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add __rcu annotations to :
(struct netdev_rx_queue)->rps_map
(struct netdev_rx_queue)->rps_flow_table
struct rps_sock_flow_table *rps_sock_flow_table;
And use appropriate rcu primitives.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The rx->count reference is used to track reference counts to the
number of rx-queue kobjects created for the device. This patch
eliminates initialization of the counter in netif_alloc_rx_queues
and instead increments the counter each time a kobject is created.
This is now symmetric with the decrement that is done when an object is
released.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
For RPS, we create a kobject for each RX queue based on the number of
queues passed to alloc_netdev_mq(). However, drivers generally do not
determine the numbers of hardware queues to use until much later, so
this usually represents the maximum number the driver may use and not
the actual number in use.
For TX queues, drivers can update the actual number using
netif_set_real_num_tx_queues(). Add a corresponding function for RX
queues, netif_set_real_num_rx_queues().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
| |
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
Enable using network namespaces with
wireless devices even when sysfs is
enabled using the same infrastructure
that was built for netdevs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add addr_assign_type to struct net_device and expose it via sysfs.
This new attribute has the purpose of giving user-space the ability to
distinguish between different assignment types of MAC addresses.
For example user-space can treat NICs with randomly generated MAC
addresses differently than NICs that have permanent (locally assigned)
MAC addresses.
For the former udev could write a persistent net rule by matching the
device path instead of the MAC address.
There's also the case of devices that 'steal' MAC addresses from slave
devices. In which it is also be beneficial for user-space to be aware
of the fact.
This patch also introduces a helper function to assist adoption of
drivers that generate MAC addresses randomly.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
CodingStyle cleanups
EXPORT_SYMBOL should immediately follow the symbol declaration.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There is a small possibility that a reader gets incorrect values on 32
bit arches. SNMP applications could catch incorrect counters when a
32bit high part is changed by another stats consumer/provider.
One way to solve this is to add a rtnl_link_stats64 param to all
ndo_get_stats64() methods, and also add such a parameter to
dev_get_stats().
Rule is that we are not allowed to use dev->stats64 as a temporary
storage for 64bit stats, but a caller provided area (usually on stack)
Old drivers (only providing get_stats() method) need no changes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Use struct rtnl_link_stats64 as the statistics structure.
On 32-bit architectures, insert 32 bits of padding after/before each
field of struct net_device_stats to make its layout compatible with
struct rtnl_link_stats64. Add an anonymous union in net_device; move
stats into the union and add struct rtnl_link_stats64 stats64.
Add net_device_ops::ndo_get_stats64, implementations of which will
return a pointer to struct rtnl_link_stats64. Drivers that implement
this operation must not update the structure asynchronously.
Change dev_get_stats() to call ndo_get_stats64 if available, and to
return a pointer to struct rtnl_link_stats64. Change callers of
dev_get_stats() accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This reverts commit aaf8cdc34ddba08122f02217d9d684e2f9f5d575.
Drivers like the ipw2100 call device_create_group when they
are initialized and device_remove_group when they are shutdown.
Moving them between namespaces deletes their sysfs groups early.
In particular the following call chain results.
netdev_unregister_kobject -> device_del -> kobject_del -> sysfs_remove_dir
With sysfs_remove_dir recursively deleting all of it's subdirectories,
and nothing adding them back.
Ouch!
Therefore we need to call something that ultimate calls sysfs_mv_dir
as that sysfs function can move sysfs directories between namespaces
without deleting their subdirectories or their contents. Allowing
us to avoid placing extra boiler plate into every driver that does
something interesting with sysfs.
Currently the function that provides that capability is device_rename.
That is the code works without nasty side effects as originally written.
So remove the misguided fix for moving devices between namespaces. The
bug in the kobject layer that inspired it has now been recognized and
fixed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
I had a couple of stupid bugs in:
netns: Teach network device kobjects which namespace they are in.
- I duplicated the Kconfig for the NET_NS
- The build was broken when sysfs was not compiled in
The sysfs breakage is because after I moved the operations
for the sysfs to the kobject layer, to make things cleaner
I forgot to move the ifdefs. Opps.
I'm not quite certain how I got introduced a second NET_NS Kconfig,
but it was probably a 3 way merge somewhere along the way that
did not notice that the NET_NS Kconfig option had mvoed and thout
that was a bug. It probably slipped in because it used to be the
sysfs patches were the first patches in my network namespace patches.
Some things just don't go like you would expect.
Neither of these bugs actually affect anything in the common case
but they should be fixed.
Thanks to Serge for noticing they were present.
Reported-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The problem. Network devices show up in sysfs and with the network
namespace active multiple devices with the same name can show up in
the same directory, ouch!
To avoid that problem and allow existing applications in network namespaces
to see the same interface that is currently presented in sysfs, this
patch enables the tagging directory support in sysfs.
By using the network namespace pointers as tags to separate out the
the sysfs directory entries we ensure that we don't have conflicts
in the directories and applications only see a limited set of
the network devices.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
|
|
|
| |
store_rps_map() & store_rps_dev_flow_table_cnt() are static.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch implements receive flow steering (RFS). RFS steers
received packets for layer 3 and 4 processing to the CPU where
the application for the corresponding flow is running. RFS is an
extension of Receive Packet Steering (RPS).
The basic idea of RFS is that when an application calls recvmsg
(or sendmsg) the application's running CPU is stored in a hash
table that is indexed by the connection's rxhash which is stored in
the socket structure. The rxhash is passed in skb's received on
the connection from netif_receive_skb. For each received packet,
the associated rxhash is used to look up the CPU in the hash table,
if a valid CPU is set then the packet is steered to that CPU using
the RPS mechanisms.
The convolution of the simple approach is that it would potentially
allow OOO packets. If threads are thrashing around CPUs or multiple
threads are trying to read from the same sockets, a quickly changing
CPU value in the hash table could cause rampant OOO packets--
we consider this a non-starter.
To avoid OOO packets, this solution implements two types of hash
tables: rps_sock_flow_table and rps_dev_flow_table.
rps_sock_table is a global hash table. Each entry is just a CPU
number and it is populated in recvmsg and sendmsg as described above.
This table contains the "desired" CPUs for flows.
rps_dev_flow_table is specific to each device queue. Each entry
contains a CPU and a tail queue counter. The CPU is the "current"
CPU for a matching flow. The tail queue counter holds the value
of a tail queue counter for the associated CPU's backlog queue at
the time of last enqueue for a flow matching the entry.
Each backlog queue has a queue head counter which is incremented
on dequeue, and so a queue tail counter is computed as queue head
count + queue length. When a packet is enqueued on a backlog queue,
the current value of the queue tail counter is saved in the hash
entry of the rps_dev_flow_table.
And now the trick: when selecting the CPU for RPS (get_rps_cpu)
the rps_sock_flow table and the rps_dev_flow table for the RX queue
are consulted. When the desired CPU for the flow (found in the
rps_sock_flow table) does not match the current CPU (found in the
rps_dev_flow table), the current CPU is changed to the desired CPU
if one of the following is true:
- The current CPU is unset (equal to RPS_NO_CPU)
- Current CPU is offline
- The current CPU's queue head counter >= queue tail counter in the
rps_dev_flow table. This checks if the queue tail has advanced
beyond the last packet that was enqueued using this table entry.
This guarantees that all packets queued using this entry have been
dequeued, thus preserving in order delivery.
Making each queue have its own rps_dev_flow table has two advantages:
1) the tail queue counters will be written on each receive, so
keeping the table local to interrupting CPU s good for locality. 2)
this allows lockless access to the table-- the CPU number and queue
tail counter need to be accessed together under mutual exclusion
from netif_receive_skb, we assume that this is only called from
device napi_poll which is non-reentrant.
This patch implements RFS for TCP and connected UDP sockets.
It should be usable for other flow oriented protocols.
There are two configuration parameters for RFS. The
"rps_flow_entries" kernel init parameter sets the number of
entries in the rps_sock_flow_table, the per rxqueue sysfs entry
"rps_flow_cnt" contains the number of entries in the rps_dev_flow
table for the rxqueue. Both are rounded to power of two.
The obvious benefit of RFS (over just RPS) is that it achieves
CPU locality between the receive processing for a flow and the
applications processing; this can result in increased performance
(higher pps, lower latency).
The benefits of RFS are dependent on cache hierarchy, application
load, and other factors. On simple benchmarks, we don't necessarily
see improvement and sometimes see degradation. However, for more
complex benchmarks and for applications where cache pressure is
much higher this technique seems to perform very well.
Below are some benchmark results which show the potential benfit of
this patch. The netperf test has 500 instances of netperf TCP_RR
test with 1 byte req. and resp. The RPC test is an request/response
test similar in structure to netperf RR test ith 100 threads on
each host, but does more work in userspace that netperf.
e1000e on 8 core Intel
No RFS or RPS 104K tps at 30% CPU
No RFS (best RPS config): 290K tps at 63% CPU
RFS 303K tps at 61% CPU
RPC test tps CPU% 50/90/99% usec latency Latency StdDev
No RFS/RPS 103K 48% 757/900/3185 4472.35
RPS only: 174K 73% 415/993/2468 491.66
RFS 223K 73% 379/651/1382 315.61
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/stmmac/stmmac_main.c
drivers/net/wireless/wl12xx/wl1271_cmd.c
drivers/net/wireless/wl12xx/wl1271_main.c
drivers/net/wireless/wl12xx/wl1271_spi.c
net/core/ethtool.c
net/mac80211/scan.c
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
| |
| |
| |
| |
| |
| | |
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| | |
Fix build with CONFIG_SYSFS not enabled.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch implements software receive side packet steering (RPS). RPS
distributes the load of received packet processing across multiple CPUs.
Problem statement: Protocol processing done in the NAPI context for received
packets is serialized per device queue and becomes a bottleneck under high
packet load. This substantially limits pps that can be achieved on a single
queue NIC and provides no scaling with multiple cores.
This solution queues packets early on in the receive path on the backlog queues
of other CPUs. This allows protocol processing (e.g. IP and TCP) to be
performed on packets in parallel. For each device (or each receive queue in
a multi-queue device) a mask of CPUs is set to indicate the CPUs that can
process packets. A CPU is selected on a per packet basis by hashing contents
of the packet header (e.g. the TCP or UDP 4-tuple) and using the result to index
into the CPU mask. The IPI mechanism is used to raise networking receive
softirqs between CPUs. This effectively emulates in software what a multi-queue
NIC can provide, but is generic requiring no device support.
Many devices now provide a hash over the 4-tuple on a per packet basis
(e.g. the Toeplitz hash). This patch allow drivers to set the HW reported hash
in an skb field, and that value in turn is used to index into the RPS maps.
Using the HW generated hash can avoid cache misses on the packet when
steering it to a remote CPU.
The CPU mask is set on a per device and per queue basis in the sysfs variable
/sys/class/net/<device>/queues/rx-<n>/rps_cpus. This is a set of canonical
bit maps for receive queues in the device (numbered by <n>). If a device
does not support multi-queue, a single variable is used for the device (rx-0).
Generally, we have found this technique increases pps capabilities of a single
queue device with good CPU utilization. Optimal settings for the CPU mask
seem to depend on architectures and cache hierarcy. Below are some results
running 500 instances of netperf TCP_RR test with 1 byte req. and resp.
Results show cumulative transaction rate and system CPU utilization.
e1000e on 8 core Intel
Without RPS: 108K tps at 33% CPU
With RPS: 311K tps at 64% CPU
forcedeth on 16 core AMD
Without RPS: 156K tps at 15% CPU
With RPS: 404K tps at 49% CPU
bnx2x on 16 core AMD
Without RPS 567K tps at 61% CPU (4 HW RX queues)
Without RPS 738K tps at 96% CPU (8 HW RX queues)
With RPS: 854K tps at 76% CPU (4 HW RX queues)
Caveats:
- The benefits of this patch are dependent on architecture and cache hierarchy.
Tuning the masks to get best performance is probably necessary.
- This patch adds overhead in the path for processing a single packet. In
a lightly loaded server this overhead may eliminate the advantages of
increased parallelism, and possibly cause some relative performance degradation.
We have found that masks that are cache aware (share same caches with
the interrupting CPU) mitigate much of this.
- The RPS masks can be changed dynamically, however whenever the mask is changed
this introduces the possibility of generating out of order packets. It's
probably best not change the masks too frequently.
Signed-off-by: Tom Herbert <therbert@google.com>
include/linux/netdevice.h | 32 ++++-
include/linux/skbuff.h | 3 +
net/core/dev.c | 335 +++++++++++++++++++++++++++++++++++++--------
net/core/net-sysfs.c | 225 ++++++++++++++++++++++++++++++-
net/core/skbuff.c | 2 +
5 files changed, 538 insertions(+), 59 deletions(-)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
The wireless sysfs methods like the rest of the networking sysfs
methods are removed with the rtnl_lock held and block until
the existing methods stop executing. So use rtnl_trylock
and restart_syscall so that the code continues to work.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Generated with the following semantic patch
@@
struct net *n1;
struct net *n2;
@@
- n1 == n2
+ net_eq(n1, n2)
@@
struct net *n1;
struct net *n2;
@@
- n1 != n2
+ !net_eq(n1, n2)
applied over {include,net,drivers/net}.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
This isn't beautifully abstracted, but it is simple,
simplifies uses and so far is only needed for the bonding driver.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
commit d519e17e2d01a0ee9abe083019532061b4438065
(net: export device speed and duplex via sysfs)
made the wrong assumption that netdev->ethtool_ops was always set.
This makes possible to crash kernel and let rtnl in locked state.
modprobe dummy
ip link set dummy0 up
(udev runs and crash)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Refactor wext to
* split out iwpriv handling
* split out iwspy handling
* split out procfs support
* allow cfg80211 to have wireless extensions compat code
w/o CONFIG_WIRELESS_EXT
After this, drivers need to
- select WIRELESS_EXT - for wext support
- select WEXT_PRIV - for iwpriv support
- select WEXT_SPY - for iwspy support
except cfg80211 -- which gets new hooks in wext-core.c
and can then get wext handlers without CONFIG_WIRELESS_EXT.
Wireless extensions procfs support is auto-selected
based on PROC_FS and anything that requires the wext core
(i.e. WIRELESS_EXT or CFG80211_WEXT).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|\ \
| |/
|/|
| | |
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
A number of drivers (recently including cfg80211-based ones)
assume that all wireless handlers, including statistics, can
sleep and they often also implicitly assume that the rtnl is
held around their invocation. This is almost always true now
except when reading from sysfs:
BUG: sleeping function called from invalid context at kernel/mutex.c:280
in_atomic(): 1, irqs_disabled(): 0, pid: 10450, name: head
2 locks held by head/10450:
#0: (&buffer->mutex){+.+.+.}, at: [<c10ceb99>] sysfs_read_file+0x24/0xf4
#1: (dev_base_lock){++.?..}, at: [<c12844ee>] wireless_show+0x1a/0x4c
Pid: 10450, comm: head Not tainted 2.6.32-rc3 #1
Call Trace:
[<c102301c>] __might_sleep+0xf0/0xf7
[<c1324355>] mutex_lock_nested+0x1a/0x33
[<f8cea53b>] wdev_lock+0xd/0xf [cfg80211]
[<f8cea58f>] cfg80211_wireless_stats+0x45/0x12d [cfg80211]
[<c13118d6>] get_wireless_stats+0x16/0x1c
[<c12844fe>] wireless_show+0x2a/0x4c
Fix this by using the rtnl instead of dev_base_lock.
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch exports the link-speed (in Mbps) and duplex of an interface
via sysfs. This eliminates the need to use ethtool just to check the
link-speed. Not requiring 'ethtool' and not relying on the SIOCETHTOOL
ioctl should be helpful in an embedded environment where space is at a
premium as well.
NOTE: This patch also intentionally allows non-root users to check the link
speed and duplex -- something not possible with ethtool.
Here's some sample output:
# cat /sys/class/net/eth0/speed
100
# cat /sys/class/net/eth0/duplex
half
# ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: Not reported
Advertised auto-negotiation: No
Speed: 100Mb/s
Duplex: Half
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: off
Supports Wake-on: g
Wake-on: g
Current message level: 0x000000ff (255)
Link detected: yes
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The move away from having drivers assign wireless handlers,
in favour of making cfg80211 assign them, broke the sysfs
registration (the wireless/ dir went missing) because the
handlers are now assigned only after registration, which is
too late.
Fix this by special-casing cfg80211-based devices, all
of which are required to have an ieee80211_ptr, in the
sysfs code, and also using get_wireless_stats() to have
the same values reported as in procfs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Tested-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
|
|
|
|
|
|
|
|
| |
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
|
|
|
|
| |
String literals are constant, and usually, we can also tag the array
of pointers const too, moving it to the .rodata section.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
BUS_ID_SIZE is really no more, and device names are dynamically
allocated and thus can be any necessary size.
So remove the BUG check here making sure BUS_ID_SIZE is at least
as large as IFNAMSIZ.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The earlier patch to fix the deadlock between a network device going
away and writing to sysfs attributes was incomplete.
- It did not set signal_pending so we would leak ERSTARTSYS to user space.
- It used ERESTARTSYS which only restarts if sigaction configures it to.
- It did not cover store and show for ifalias.
So fix all of these up and use the new helper restart_syscall so we get
the details correct on what it takes.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
Since dev_set_name takes a printf style string, new gcc complains
if arg is not const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
| |
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch will filter out the uevent not related to the init_net.
Without this patch if a network device is created in a network
namespace with the same name as one network device belonging to the
initial network namespace (eg. eth0), when the network namespace
will die and the network device will be destroyed, an event will
be sent and catched by the udevd daemon. That will result to have
the real network device to be shutdown because the udevd/uevent are
not namespace aware.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|