From 1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 16 Apr 2005 15:20:36 -0700 Subject: Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! --- drivers/scsi/tmscsim.h | 565 +++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 565 insertions(+) create mode 100644 drivers/scsi/tmscsim.h (limited to 'drivers/scsi/tmscsim.h') diff --git a/drivers/scsi/tmscsim.h b/drivers/scsi/tmscsim.h new file mode 100644 index 0000000..d449527 --- /dev/null +++ b/drivers/scsi/tmscsim.h @@ -0,0 +1,565 @@ +/*********************************************************************** +;* File Name : TMSCSIM.H * +;* TEKRAM DC-390(T) PCI SCSI Bus Master Host Adapter * +;* Device Driver * +;***********************************************************************/ +/* $Id: tmscsim.h,v 2.15.2.3 2000/11/17 20:52:27 garloff Exp $ */ + +#ifndef _TMSCSIM_H +#define _TMSCSIM_H + +#include +#include + +#define SCSI_IRQ_NONE 255 + +#define MAX_ADAPTER_NUM 4 +#define MAX_SG_LIST_BUF 16 /* Not used */ +#define MAX_SCSI_ID 8 +#define MAX_SRB_CNT 50 /* Max number of started commands */ + +#define SEL_TIMEOUT 153 /* 250 ms selection timeout (@ 40 MHz) */ + +#define pci_dma_lo32(a) (a & 0xffffffff) + +typedef u8 UCHAR; /* 8 bits */ +typedef u16 USHORT; /* 16 bits */ +typedef u32 UINT; /* 32 bits */ +typedef unsigned long ULONG; /* 32/64 bits */ + + +/* +;----------------------------------------------------------------------- +; SCSI Request Block +;----------------------------------------------------------------------- +*/ +struct dc390_srb +{ +//u8 CmdBlock[12]; + +struct dc390_srb *pNextSRB; +struct dc390_dcb *pSRBDCB; +struct scsi_cmnd *pcmd; +struct scatterlist *pSegmentList; + +struct scatterlist Segmentx; /* make a one entry of S/G list table */ + +unsigned long SGBusAddr; /*;a segment starting address as seen by AM53C974A*/ +unsigned long SGToBeXferLen; /*; to be xfer length */ +unsigned long TotalXferredLen; +unsigned long SavedTotXLen; +unsigned long Saved_Ptr; +u32 SRBState; + +u8 SRBStatus; +u8 SRBFlag; /*; b0-AutoReqSense,b6-Read,b7-write */ + /*; b4-settimeout,b5-Residual valid */ +u8 AdaptStatus; +u8 TargetStatus; + +u8 ScsiPhase; +s8 TagNumber; +u8 SGIndex; +u8 SGcount; + +u8 MsgCnt; +u8 EndMessage; +u8 SavedSGCount; + +u8 MsgInBuf[6]; +u8 MsgOutBuf[6]; + +//u8 IORBFlag; /*;81h-Reset, 2-retry */ +}; + + +/* +;----------------------------------------------------------------------- +; Device Control Block +;----------------------------------------------------------------------- +*/ +struct dc390_dcb +{ +struct dc390_dcb *pNextDCB; +struct dc390_acb *pDCBACB; + +/* Queued SRBs */ +struct dc390_srb *pGoingSRB; +struct dc390_srb *pGoingLast; +struct dc390_srb *pActiveSRB; +u8 GoingSRBCnt; + +u32 TagMask; + +u8 TargetID; /*; SCSI Target ID (SCSI Only) */ +u8 TargetLUN; /*; SCSI Log. Unit (SCSI Only) */ +u8 DevMode; +u8 DCBFlag; + +u8 CtrlR1; +u8 CtrlR3; +u8 CtrlR4; + +u8 SyncMode; /*; 0:async mode */ +u8 NegoPeriod; /*;for nego. */ +u8 SyncPeriod; /*;for reg. */ +u8 SyncOffset; /*;for reg. and nego.(low nibble) */ +}; + + +/* +;----------------------------------------------------------------------- +; Adapter Control Block +;----------------------------------------------------------------------- +*/ +struct dc390_acb +{ +struct Scsi_Host *pScsiHost; +u16 IOPortBase; +u8 IRQLevel; +u8 status; + +u8 SRBCount; +u8 AdapterIndex; /*; nth Adapter this driver */ +u8 DCBCnt; + +u8 TagMaxNum; +u8 ACBFlag; +u8 Gmode2; +u8 scan_devices; + +struct dc390_dcb *pLinkDCB; +struct dc390_dcb *pLastDCB; +struct dc390_dcb *pDCBRunRobin; + +struct dc390_dcb *pActiveDCB; +struct dc390_srb *pFreeSRB; +struct dc390_srb *pTmpSRB; + +u8 msgin123[4]; +u8 Connected; +u8 pad; + +#if defined(USE_SPINLOCKS) && USE_SPINLOCKS > 1 && (defined(CONFIG_SMP) || DEBUG_SPINLOCKS > 0) +spinlock_t lock; +#endif +u8 sel_timeout; +u8 glitch_cfg; + +u8 MsgLen; +u8 Ignore_IRQ; /* Not used */ + +struct pci_dev *pdev; + +unsigned long Cmds; +u32 SelLost; +u32 SelConn; +u32 CmdInQ; +u32 CmdOutOfSRB; + +struct dc390_srb TmpSRB; +struct dc390_srb SRB_array[MAX_SRB_CNT]; /* 50 SRBs */ +}; + + +/*;-----------------------------------------------------------------------*/ + + +#define BIT31 0x80000000 +#define BIT30 0x40000000 +#define BIT29 0x20000000 +#define BIT28 0x10000000 +#define BIT27 0x08000000 +#define BIT26 0x04000000 +#define BIT25 0x02000000 +#define BIT24 0x01000000 +#define BIT23 0x00800000 +#define BIT22 0x00400000 +#define BIT21 0x00200000 +#define BIT20 0x00100000 +#define BIT19 0x00080000 +#define BIT18 0x00040000 +#define BIT17 0x00020000 +#define BIT16 0x00010000 +#define BIT15 0x00008000 +#define BIT14 0x00004000 +#define BIT13 0x00002000 +#define BIT12 0x00001000 +#define BIT11 0x00000800 +#define BIT10 0x00000400 +#define BIT9 0x00000200 +#define BIT8 0x00000100 +#define BIT7 0x00000080 +#define BIT6 0x00000040 +#define BIT5 0x00000020 +#define BIT4 0x00000010 +#define BIT3 0x00000008 +#define BIT2 0x00000004 +#define BIT1 0x00000002 +#define BIT0 0x00000001 + +/*;---UnitCtrlFlag */ +#define UNIT_ALLOCATED BIT0 +#define UNIT_INFO_CHANGED BIT1 +#define FORMATING_MEDIA BIT2 +#define UNIT_RETRY BIT3 + +/*;---UnitFlags */ +#define DASD_SUPPORT BIT0 +#define SCSI_SUPPORT BIT1 +#define ASPI_SUPPORT BIT2 + +/*;----SRBState machine definition */ +#define SRB_FREE 0 +#define SRB_WAIT BIT0 +#define SRB_READY BIT1 +#define SRB_MSGOUT BIT2 /*;arbitration+msg_out 1st byte*/ +#define SRB_MSGIN BIT3 +#define SRB_MSGIN_MULTI BIT4 +#define SRB_COMMAND BIT5 +#define SRB_START_ BIT6 /*;arbitration+msg_out+command_out*/ +#define SRB_DISCONNECT BIT7 +#define SRB_DATA_XFER BIT8 +#define SRB_XFERPAD BIT9 +#define SRB_STATUS BIT10 +#define SRB_COMPLETED BIT11 +#define SRB_ABORT_SENT BIT12 +#define DO_SYNC_NEGO BIT13 +#define SRB_UNEXPECT_RESEL BIT14 + +/*;---SRBstatus */ +#define SRB_OK BIT0 +#define ABORTION BIT1 +#define OVER_RUN BIT2 +#define UNDER_RUN BIT3 +#define PARITY_ERROR BIT4 +#define SRB_ERROR BIT5 + +/*;---ACBFlag */ +#define RESET_DEV BIT0 +#define RESET_DETECT BIT1 +#define RESET_DONE BIT2 + +/*;---DCBFlag */ +#define ABORT_DEV_ BIT0 + +/*;---SRBFlag */ +#define DATAOUT BIT7 +#define DATAIN BIT6 +#define RESIDUAL_VALID BIT5 +#define ENABLE_TIMER BIT4 +#define RESET_DEV0 BIT2 +#define ABORT_DEV BIT1 +#define AUTO_REQSENSE BIT0 + +/*;---Adapter status */ +#define H_STATUS_GOOD 0 +#define H_SEL_TIMEOUT 0x11 +#define H_OVER_UNDER_RUN 0x12 +#define H_UNEXP_BUS_FREE 0x13 +#define H_TARGET_PHASE_F 0x14 +#define H_INVALID_CCB_OP 0x16 +#define H_LINK_CCB_BAD 0x17 +#define H_BAD_TARGET_DIR 0x18 +#define H_DUPLICATE_CCB 0x19 +#define H_BAD_CCB_OR_SG 0x1A +#define H_ABORT 0x0FF + +/*; SCSI Status byte codes*/ +/* The values defined in include/scsi/scsi.h, to be shifted << 1 */ + +#define SCSI_STAT_UNEXP_BUS_F 0xFD /*; Unexpect Bus Free */ +#define SCSI_STAT_BUS_RST_DETECT 0xFE /*; Scsi Bus Reset detected */ +#define SCSI_STAT_SEL_TIMEOUT 0xFF /*; Selection Time out */ + +/* cmd->result */ +#define RES_TARGET 0x000000FF /* Target State */ +#define RES_TARGET_LNX STATUS_MASK /* Only official ... */ +#define RES_ENDMSG 0x0000FF00 /* End Message */ +#define RES_DID 0x00FF0000 /* DID_ codes */ +#define RES_DRV 0xFF000000 /* DRIVER_ codes */ + +#define MK_RES(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt)) +#define MK_RES_LNX(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt)<<1) + +#define SET_RES_TARGET(who, tgt) do { who &= ~RES_TARGET; who |= (int)(tgt); } while (0) +#define SET_RES_TARGET_LNX(who, tgt) do { who &= ~RES_TARGET_LNX; who |= (int)(tgt) << 1; } while (0) +#define SET_RES_MSG(who, msg) do { who &= ~RES_ENDMSG; who |= (int)(msg) << 8; } while (0) +#define SET_RES_DID(who, did) do { who &= ~RES_DID; who |= (int)(did) << 16; } while (0) +#define SET_RES_DRV(who, drv) do { who &= ~RES_DRV; who |= (int)(drv) << 24; } while (0) + +/*;---Sync_Mode */ +#define SYNC_DISABLE 0 +#define SYNC_ENABLE BIT0 +#define SYNC_NEGO_DONE BIT1 +#define WIDE_ENABLE BIT2 /* Not used ;-) */ +#define WIDE_NEGO_DONE BIT3 /* Not used ;-) */ +#define EN_TAG_QUEUEING BIT4 +#define EN_ATN_STOP BIT5 + +#define SYNC_NEGO_OFFSET 15 + +/*;---SCSI bus phase*/ +#define SCSI_DATA_OUT 0 +#define SCSI_DATA_IN 1 +#define SCSI_COMMAND 2 +#define SCSI_STATUS_ 3 +#define SCSI_NOP0 4 +#define SCSI_NOP1 5 +#define SCSI_MSG_OUT 6 +#define SCSI_MSG_IN 7 + +/*;----SCSI MSG BYTE*/ /* see scsi/scsi.h */ /* One is missing ! */ +#define ABORT_TAG 0x0d + +/* + * SISC query queue + */ +typedef struct { + dma_addr_t saved_dma_handle; +} dc390_cmd_scp_t; + +/* +;========================================================== +; EEPROM byte offset +;========================================================== +*/ +typedef struct _EEprom +{ +u8 EE_MODE1; +u8 EE_SPEED; +u8 xx1; +u8 xx2; +} EEprom, *PEEprom; + +#define REAL_EE_ADAPT_SCSI_ID 64 +#define REAL_EE_MODE2 65 +#define REAL_EE_DELAY 66 +#define REAL_EE_TAG_CMD_NUM 67 + +#define EE_ADAPT_SCSI_ID 32 +#define EE_MODE2 33 +#define EE_DELAY 34 +#define EE_TAG_CMD_NUM 35 + +#define EE_LEN 40 + +/*; EE_MODE1 bits definition*/ +#define PARITY_CHK_ BIT0 +#define SYNC_NEGO_ BIT1 +#define EN_DISCONNECT_ BIT2 +#define SEND_START_ BIT3 +#define TAG_QUEUEING_ BIT4 + +/*; EE_MODE2 bits definition*/ +#define MORE2_DRV BIT0 +#define GREATER_1G BIT1 +#define RST_SCSI_BUS BIT2 +#define ACTIVE_NEGATION BIT3 +#define NO_SEEK BIT4 +#define LUN_CHECK BIT5 + +#define ENABLE_CE 1 +#define DISABLE_CE 0 +#define EEPROM_READ 0x80 + +/* +;========================================================== +; AMD 53C974 Registers bit Definition +;========================================================== +*/ +/* +;==================== +; SCSI Register +;==================== +*/ + +/*; Command Reg.(+0CH) (rw) */ +#define DMA_COMMAND BIT7 +#define NOP_CMD 0 +#define CLEAR_FIFO_CMD 1 +#define RST_DEVICE_CMD 2 +#define RST_SCSI_BUS_CMD 3 + +#define INFO_XFER_CMD 0x10 +#define INITIATOR_CMD_CMPLTE 0x11 +#define MSG_ACCEPTED_CMD 0x12 +#define XFER_PAD_BYTE 0x18 +#define SET_ATN_CMD 0x1A +#define RESET_ATN_CMD 0x1B + +#define SEL_WO_ATN 0x41 /* currently not used */ +#define SEL_W_ATN 0x42 +#define SEL_W_ATN_STOP 0x43 +#define SEL_W_ATN3 0x46 +#define EN_SEL_RESEL 0x44 +#define DIS_SEL_RESEL 0x45 /* currently not used */ +#define RESEL 0x40 /* " */ +#define RESEL_ATN3 0x47 /* " */ + +#define DATA_XFER_CMD INFO_XFER_CMD + + +/*; SCSI Status Reg.(+10H) (r) */ +#define INTERRUPT BIT7 +#define ILLEGAL_OP_ERR BIT6 +#define PARITY_ERR BIT5 +#define COUNT_2_ZERO BIT4 +#define GROUP_CODE_VALID BIT3 +#define SCSI_PHASE_MASK (BIT2+BIT1+BIT0) +/* BIT2: MSG phase; BIT1: C/D physe; BIT0: I/O phase */ + +/*; Interrupt Status Reg.(+14H) (r) */ +#define SCSI_RESET BIT7 +#define INVALID_CMD BIT6 +#define DISCONNECTED BIT5 +#define SERVICE_REQUEST BIT4 +#define SUCCESSFUL_OP BIT3 +#define RESELECTED BIT2 +#define SEL_ATTENTION BIT1 +#define SELECTED BIT0 + +/*; Internal State Reg.(+18H) (r) */ +#define SYNC_OFFSET_FLAG BIT3 +#define INTRN_STATE_MASK (BIT2+BIT1+BIT0) +/* 0x04: Sel. successful (w/o stop), 0x01: Sel. successful (w/ stop) */ + +/*; Clock Factor Reg.(+24H) (w) */ +#define CLK_FREQ_40MHZ 0 +#define CLK_FREQ_35MHZ (BIT2+BIT1+BIT0) +#define CLK_FREQ_30MHZ (BIT2+BIT1) +#define CLK_FREQ_25MHZ (BIT2+BIT0) +#define CLK_FREQ_20MHZ BIT2 +#define CLK_FREQ_15MHZ (BIT1+BIT0) +#define CLK_FREQ_10MHZ BIT1 + +/*; Control Reg. 1(+20H) (rw) */ +#define EXTENDED_TIMING BIT7 +#define DIS_INT_ON_SCSI_RST BIT6 +#define PARITY_ERR_REPO BIT4 +#define SCSI_ID_ON_BUS (BIT2+BIT1+BIT0) /* host adapter ID */ + +/*; Control Reg. 2(+2CH) (rw) */ +#define EN_FEATURE BIT6 +#define EN_SCSI2_CMD BIT3 + +/*; Control Reg. 3(+30H) (rw) */ +#define ID_MSG_CHECK BIT7 +#define EN_QTAG_MSG BIT6 +#define EN_GRP2_CMD BIT5 +#define FAST_SCSI BIT4 /* ;10MB/SEC */ +#define FAST_CLK BIT3 /* ;25 - 40 MHZ */ + +/*; Control Reg. 4(+34H) (rw) */ +#define EATER_12NS 0 +#define EATER_25NS BIT7 +#define EATER_35NS BIT6 +#define EATER_0NS (BIT7+BIT6) +#define REDUCED_POWER BIT5 +#define CTRL4_RESERVED BIT4 /* must be 1 acc. to AM53C974.c */ +#define NEGATE_REQACKDATA BIT2 +#define NEGATE_REQACK BIT3 + +#define GLITCH_TO_NS(x) (((~x>>6 & 2) >> 1) | ((x>>6 & 1) << 1 ^ (x>>6 & 2))) +#define NS_TO_GLITCH(y) (((~y<<7) | ~((y<<6) ^ ((y<<5 & 1<<6) | ~0x40))) & 0xc0) + +/* +;==================== +; DMA Register +;==================== +*/ +/*; DMA Command Reg.(+40H) (rw) */ +#define READ_DIRECTION BIT7 +#define WRITE_DIRECTION 0 +#define EN_DMA_INT BIT6 +#define EN_PAGE_INT BIT5 /* page transfer interrupt enable */ +#define MAP_TO_MDL BIT4 +#define DIAGNOSTIC BIT2 +#define DMA_IDLE_CMD 0 +#define DMA_BLAST_CMD BIT0 +#define DMA_ABORT_CMD BIT1 +#define DMA_START_CMD (BIT1+BIT0) + +/*; DMA Status Reg.(+54H) (r) */ +#define PCI_MS_ABORT BIT6 +#define BLAST_COMPLETE BIT5 +#define SCSI_INTERRUPT BIT4 +#define DMA_XFER_DONE BIT3 +#define DMA_XFER_ABORT BIT2 +#define DMA_XFER_ERROR BIT1 +#define POWER_DOWN BIT0 + +/*; DMA SCSI Bus and Ctrl.(+70H) */ +#define EN_INT_ON_PCI_ABORT BIT25 +#define WRT_ERASE_DMA_STAT BIT24 +#define PW_DOWN_CTRL BIT21 +#define SCSI_BUSY BIT20 +#define SCLK BIT19 +#define SCAM BIT18 +#define SCSI_LINES 0x0003ffff + +/* +;========================================================== +; SCSI Chip register address offset +;========================================================== +;Registers are rw unless declared otherwise +*/ +#define CtcReg_Low 0x00 /* r curr. transfer count */ +#define CtcReg_Mid 0x04 /* r */ +#define CtcReg_High 0x38 /* r */ +#define ScsiFifo 0x08 +#define ScsiCmd 0x0C +#define Scsi_Status 0x10 /* r */ +#define INT_Status 0x14 /* r */ +#define Sync_Period 0x18 /* w */ +#define Sync_Offset 0x1C /* w */ +#define Clk_Factor 0x24 /* w */ +#define CtrlReg1 0x20 +#define CtrlReg2 0x2C +#define CtrlReg3 0x30 +#define CtrlReg4 0x34 +#define DMA_Cmd 0x40 +#define DMA_XferCnt 0x44 /* rw starting transfer count (32 bit) */ +#define DMA_XferAddr 0x48 /* rw starting physical address (32 bit) */ +#define DMA_Wk_ByteCntr 0x4C /* r working byte counter */ +#define DMA_Wk_AddrCntr 0x50 /* r working address counter */ +#define DMA_Status 0x54 /* r */ +#define DMA_MDL_Addr 0x58 /* rw starting MDL address */ +#define DMA_Wk_MDL_Cntr 0x5C /* r working MDL counter */ +#define DMA_ScsiBusCtrl 0x70 /* rw SCSI Bus, PCI/DMA Ctrl */ + +#define StcReg_Low CtcReg_Low /* w start transfer count */ +#define StcReg_Mid CtcReg_Mid /* w */ +#define StcReg_High CtcReg_High /* w */ +#define Scsi_Dest_ID Scsi_Status /* w */ +#define Scsi_TimeOut INT_Status /* w */ +#define Intern_State Sync_Period /* r */ +#define Current_Fifo Sync_Offset /* r Curr. FIFO / int. state */ + + +#define DC390_read8(address) \ + (inb (pACB->IOPortBase + (address))) + +#define DC390_read8_(address, base) \ + (inb ((u16)(base) + (address))) + +#define DC390_read16(address) \ + (inw (pACB->IOPortBase + (address))) + +#define DC390_read32(address) \ + (inl (pACB->IOPortBase + (address))) + +#define DC390_write8(address,value) \ + outb ((value), pACB->IOPortBase + (address)) + +#define DC390_write8_(address,value,base) \ + outb ((value), (u16)(base) + (address)) + +#define DC390_write16(address,value) \ + outw ((value), pACB->IOPortBase + (address)) + +#define DC390_write32(address,value) \ + outl ((value), pACB->IOPortBase + (address)) + + +#endif /* _TMSCSIM_H */ -- cgit v1.1