diff options
Diffstat (limited to 'drivers/ata')
| -rw-r--r-- | drivers/ata/Kconfig | 1 | ||||
| -rw-r--r-- | drivers/ata/Makefile | 1 | ||||
| -rw-r--r-- | drivers/ata/pata_legacy.c | 15 | ||||
| -rw-r--r-- | drivers/ata/pata_winbond.c | 282 |
4 files changed, 14 insertions, 285 deletions
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig index 65e3e27..11ec911 100644 --- a/drivers/ata/Kconfig +++ b/drivers/ata/Kconfig @@ -828,6 +828,7 @@ config PATA_SAMSUNG_CF config PATA_WINBOND_VLB tristate "Winbond W83759A VLB PATA support (Experimental)" depends on ISA && EXPERIMENTAL + select PATA_LEGACY help Support for the Winbond W83759A controller on Vesa Local Bus systems. diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile index 158eaa9..d5df04a 100644 --- a/drivers/ata/Makefile +++ b/drivers/ata/Makefile @@ -89,7 +89,6 @@ obj-$(CONFIG_PATA_QDI) += pata_qdi.o obj-$(CONFIG_PATA_RB532) += pata_rb532_cf.o obj-$(CONFIG_PATA_RZ1000) += pata_rz1000.o obj-$(CONFIG_PATA_SAMSUNG_CF) += pata_samsung_cf.o -obj-$(CONFIG_PATA_WINBOND_VLB) += pata_winbond.o obj-$(CONFIG_PATA_PXA) += pata_pxa.o diff --git a/drivers/ata/pata_legacy.c b/drivers/ata/pata_legacy.c index 9df1ff7..eaf1941 100644 --- a/drivers/ata/pata_legacy.c +++ b/drivers/ata/pata_legacy.c @@ -44,6 +44,9 @@ * Specific support is included for the ht6560a/ht6560b/opti82c611a/ * opti82c465mv/promise 20230c/20630/qdi65x0/winbond83759A * + * Support for the Winbond 83759A when operating in advanced mode. + * Multichip mode is not currently supported. + * * Use the autospeed and pio_mask options with: * Appian ADI/2 aka CLPD7220 or AIC25VL01. * Use the jumpers, autospeed and set pio_mask to the mode on the jumpers with @@ -135,12 +138,18 @@ static int ht6560b; /* HT 6560A on primary 1, second 2, both 3 */ static int opti82c611a; /* Opti82c611A on primary 1, sec 2, both 3 */ static int opti82c46x; /* Opti 82c465MV present(pri/sec autodetect) */ static int qdi; /* Set to probe QDI controllers */ -static int winbond; /* Set to probe Winbond controllers, - give I/O port if non standard */ static int autospeed; /* Chip present which snoops speed changes */ static int pio_mask = ATA_PIO4; /* PIO range for autospeed devices */ static int iordy_mask = 0xFFFFFFFF; /* Use iordy if available */ +#ifdef PATA_WINBOND_VLB_MODULE +static int winbond = 1; /* Set to probe Winbond controllers, + give I/O port if non standard */ +#else +static int winbond; /* Set to probe Winbond controllers, + give I/O port if non standard */ +#endif + /** * legacy_probe_add - Add interface to probe list * @port: Controller port @@ -1297,6 +1306,7 @@ MODULE_AUTHOR("Alan Cox"); MODULE_DESCRIPTION("low-level driver for legacy ATA"); MODULE_LICENSE("GPL"); MODULE_VERSION(DRV_VERSION); +MODULE_ALIAS("pata_winbond"); module_param(probe_all, int, 0); module_param(autospeed, int, 0); @@ -1305,6 +1315,7 @@ module_param(ht6560b, int, 0); module_param(opti82c611a, int, 0); module_param(opti82c46x, int, 0); module_param(qdi, int, 0); +module_param(winbond, int, 0); module_param(pio_mask, int, 0); module_param(iordy_mask, int, 0); diff --git a/drivers/ata/pata_winbond.c b/drivers/ata/pata_winbond.c deleted file mode 100644 index 6d8619b..0000000 --- a/drivers/ata/pata_winbond.c +++ /dev/null @@ -1,282 +0,0 @@ -/* - * pata_winbond.c - Winbond VLB ATA controllers - * (C) 2006 Red Hat - * - * Support for the Winbond 83759A when operating in advanced mode. - * Multichip mode is not currently supported. - */ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/init.h> -#include <linux/blkdev.h> -#include <linux/delay.h> -#include <scsi/scsi_host.h> -#include <linux/libata.h> -#include <linux/platform_device.h> - -#define DRV_NAME "pata_winbond" -#define DRV_VERSION "0.0.3" - -#define NR_HOST 4 /* Two winbond controllers, two channels each */ - -struct winbond_data { - unsigned long config; - struct platform_device *platform_dev; -}; - -static struct ata_host *winbond_host[NR_HOST]; -static struct winbond_data winbond_data[NR_HOST]; -static int nr_winbond_host; - -#ifdef MODULE -static int probe_winbond = 1; -#else -static int probe_winbond; -#endif - -static DEFINE_SPINLOCK(winbond_lock); - -static void winbond_writecfg(unsigned long port, u8 reg, u8 val) -{ - unsigned long flags; - spin_lock_irqsave(&winbond_lock, flags); - outb(reg, port + 0x01); - outb(val, port + 0x02); - spin_unlock_irqrestore(&winbond_lock, flags); -} - -static u8 winbond_readcfg(unsigned long port, u8 reg) -{ - u8 val; - - unsigned long flags; - spin_lock_irqsave(&winbond_lock, flags); - outb(reg, port + 0x01); - val = inb(port + 0x02); - spin_unlock_irqrestore(&winbond_lock, flags); - - return val; -} - -static void winbond_set_piomode(struct ata_port *ap, struct ata_device *adev) -{ - struct ata_timing t; - struct winbond_data *winbond = ap->host->private_data; - int active, recovery; - u8 reg; - int timing = 0x88 + (ap->port_no * 4) + (adev->devno * 2); - - reg = winbond_readcfg(winbond->config, 0x81); - - /* Get the timing data in cycles */ - if (reg & 0x40) /* Fast VLB bus, assume 50MHz */ - ata_timing_compute(adev, adev->pio_mode, &t, 20000, 1000); - else - ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000); - - active = (clamp_val(t.active, 3, 17) - 1) & 0x0F; - recovery = (clamp_val(t.recover, 1, 15) + 1) & 0x0F; - timing = (active << 4) | recovery; - winbond_writecfg(winbond->config, timing, reg); - - /* Load the setup timing */ - - reg = 0x35; - if (adev->class != ATA_DEV_ATA) - reg |= 0x08; /* FIFO off */ - if (!ata_pio_need_iordy(adev)) - reg |= 0x02; /* IORDY off */ - reg |= (clamp_val(t.setup, 0, 3) << 6); - winbond_writecfg(winbond->config, timing + 1, reg); -} - - -static unsigned int winbond_data_xfer(struct ata_device *dev, - unsigned char *buf, unsigned int buflen, int rw) -{ - struct ata_port *ap = dev->link->ap; - int slop = buflen & 3; - - if (ata_id_has_dword_io(dev->id)) { - if (rw == READ) - ioread32_rep(ap->ioaddr.data_addr, buf, buflen >> 2); - else - iowrite32_rep(ap->ioaddr.data_addr, buf, buflen >> 2); - - if (unlikely(slop)) { - __le32 pad; - if (rw == READ) { - pad = cpu_to_le32(ioread32(ap->ioaddr.data_addr)); - memcpy(buf + buflen - slop, &pad, slop); - } else { - memcpy(&pad, buf + buflen - slop, slop); - iowrite32(le32_to_cpu(pad), ap->ioaddr.data_addr); - } - buflen += 4 - slop; - } - } else - buflen = ata_sff_data_xfer(dev, buf, buflen, rw); - - return buflen; -} - -static struct scsi_host_template winbond_sht = { - ATA_PIO_SHT(DRV_NAME), -}; - -static struct ata_port_operations winbond_port_ops = { - .inherits = &ata_sff_port_ops, - .sff_data_xfer = winbond_data_xfer, - .cable_detect = ata_cable_40wire, - .set_piomode = winbond_set_piomode, -}; - -/** - * winbond_init_one - attach a winbond interface - * @type: Type to display - * @io: I/O port start - * @irq: interrupt line - * @fast: True if on a > 33Mhz VLB - * - * Register a VLB bus IDE interface. Such interfaces are PIO and we - * assume do not support IRQ sharing. - */ - -static __init int winbond_init_one(unsigned long port) -{ - struct platform_device *pdev; - u8 reg; - int i, rc; - - reg = winbond_readcfg(port, 0x81); - reg |= 0x80; /* jumpered mode off */ - winbond_writecfg(port, 0x81, reg); - reg = winbond_readcfg(port, 0x83); - reg |= 0xF0; /* local control */ - winbond_writecfg(port, 0x83, reg); - reg = winbond_readcfg(port, 0x85); - reg |= 0xF0; /* programmable timing */ - winbond_writecfg(port, 0x85, reg); - - reg = winbond_readcfg(port, 0x81); - - if (!(reg & 0x03)) /* Disabled */ - return -ENODEV; - - for (i = 0; i < 2 ; i ++) { - unsigned long cmd_port = 0x1F0 - (0x80 * i); - unsigned long ctl_port = cmd_port + 0x206; - struct ata_host *host; - struct ata_port *ap; - void __iomem *cmd_addr, *ctl_addr; - - if (!(reg & (1 << i))) - continue; - - pdev = platform_device_register_simple(DRV_NAME, nr_winbond_host, NULL, 0); - if (IS_ERR(pdev)) - return PTR_ERR(pdev); - - rc = -ENOMEM; - host = ata_host_alloc(&pdev->dev, 1); - if (!host) - goto err_unregister; - ap = host->ports[0]; - - rc = -ENOMEM; - cmd_addr = devm_ioport_map(&pdev->dev, cmd_port, 8); - ctl_addr = devm_ioport_map(&pdev->dev, ctl_port, 1); - if (!cmd_addr || !ctl_addr) - goto err_unregister; - - ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx", cmd_port, ctl_port); - - ap->ops = &winbond_port_ops; - ap->pio_mask = ATA_PIO4; - ap->flags |= ATA_FLAG_SLAVE_POSS; - ap->ioaddr.cmd_addr = cmd_addr; - ap->ioaddr.altstatus_addr = ctl_addr; - ap->ioaddr.ctl_addr = ctl_addr; - ata_sff_std_ports(&ap->ioaddr); - - /* hook in a private data structure per channel */ - host->private_data = &winbond_data[nr_winbond_host]; - winbond_data[nr_winbond_host].config = port; - winbond_data[nr_winbond_host].platform_dev = pdev; - - /* activate */ - rc = ata_host_activate(host, 14 + i, ata_sff_interrupt, 0, - &winbond_sht); - if (rc) - goto err_unregister; - - winbond_host[nr_winbond_host++] = dev_get_drvdata(&pdev->dev); - } - - return 0; - - err_unregister: - platform_device_unregister(pdev); - return rc; -} - -/** - * winbond_init - attach winbond interfaces - * - * Attach winbond IDE interfaces by scanning the ports it may occupy. - */ - -static __init int winbond_init(void) -{ - static const unsigned long config[2] = { 0x130, 0x1B0 }; - - int ct = 0; - int i; - - if (probe_winbond == 0) - return -ENODEV; - - /* - * Check both base addresses - */ - - for (i = 0; i < 2; i++) { - if (probe_winbond & (1<<i)) { - int ret = 0; - unsigned long port = config[i]; - - if (request_region(port, 2, "pata_winbond")) { - ret = winbond_init_one(port); - if (ret <= 0) - release_region(port, 2); - else ct+= ret; - } - } - } - if (ct != 0) - return 0; - return -ENODEV; -} - -static __exit void winbond_exit(void) -{ - int i; - - for (i = 0; i < nr_winbond_host; i++) { - ata_host_detach(winbond_host[i]); - release_region(winbond_data[i].config, 2); - platform_device_unregister(winbond_data[i].platform_dev); - } -} - -MODULE_AUTHOR("Alan Cox"); -MODULE_DESCRIPTION("low-level driver for Winbond VL ATA"); -MODULE_LICENSE("GPL"); -MODULE_VERSION(DRV_VERSION); - -module_init(winbond_init); -module_exit(winbond_exit); - -module_param(probe_winbond, int, 0); - |