diff options
Diffstat (limited to 'drivers/net/Kconfig')
| -rw-r--r-- | drivers/net/Kconfig | 57 |
1 files changed, 39 insertions, 18 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index b941c74..43d0317 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -25,6 +25,14 @@ menuconfig NETDEVICES # that for each of the symbols. if NETDEVICES +config NETDEVICES_MULTIQUEUE + bool "Netdevice multiple hardware queue support" + ---help--- + Say Y here if you want to allow the network stack to use multiple + hardware TX queues on an ethernet device. + + Most people will say N here. + config IFB tristate "Intermediate Functional Block support" depends on NET_CLS_ACT @@ -74,6 +82,16 @@ config BONDING To compile this driver as a module, choose M here: the module will be called bonding. +config MACVLAN + tristate "MAC-VLAN support (EXPERIMENTAL)" + depends on EXPERIMENTAL + ---help--- + This allows one to create virtual interfaces that map packets to + or from specific MAC addresses to a particular interface. + + To compile this driver as a module, choose M here: the module + will be called macvlan. + config EQUALIZER tristate "EQL (serial line load balancing) support" ---help--- @@ -187,7 +205,7 @@ config MII config MACB tristate "Atmel MACB support" depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 - select MII + select PHYLIB help The Atmel MACB ethernet interface is found on many AT32 and AT91 parts. Say Y to include support for the MACB chip. @@ -387,22 +405,6 @@ config ATARILANCE on the AMD Lance chipset: RieblCard (with or without battery), or PAMCard VME (also the version by Rhotron, with different addresses). -config ATARI_BIONET - tristate "BioNet-100 support" - depends on ATARI && ATARI_ACSI && BROKEN - help - Say Y to include support for BioData's BioNet-100 Ethernet adapter - for the ACSI port. The driver works (has to work...) with a polled - I/O scheme, so it's rather slow :-( - -config ATARI_PAMSNET - tristate "PAMsNet support" - depends on ATARI && ATARI_ACSI && BROKEN - help - Say Y to include support for the PAMsNet Ethernet adapter for the - ACSI port ("ACSI node"). The driver works (has to work...) with a - polled I/O scheme, so it's rather slow :-( - config SUN3LANCE tristate "Sun3/Sun3x on-board LANCE support" depends on SUN3 || SUN3X @@ -586,6 +588,12 @@ config CASSINI Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also <http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf> +config SUNVNET + tristate "Sun Virtual Network support" + depends on SUN_LDOMS + help + Support for virtual network devices under Sun Logical Domains. + config NET_VENDOR_3COM bool "3COM cards" depends on ISA || EISA || MCA || PCI @@ -877,7 +885,7 @@ config NET_NETX config DM9000 tristate "DM9000 support" - depends on ARM || MIPS + depends on ARM || BLACKFIN || MIPS select CRC32 select MII ---help--- @@ -2784,6 +2792,19 @@ config PPPOATM which can lead to bad results if the ATM peer loses state and changes its encapsulation unilaterally. +config PPPOL2TP + tristate "PPP over L2TP (EXPERIMENTAL)" + depends on EXPERIMENTAL && PPP + help + Support for PPP-over-L2TP socket family. L2TP is a protocol + used by ISPs and enterprises to tunnel PPP traffic over UDP + tunnels. L2TP is replacing PPTP for VPN uses. + + This kernel component handles only L2TP data packets: a + userland daemon handles L2TP the control protocol (tunnel + and session setup). One such daemon is OpenL2TP + (http://openl2tp.sourceforge.net/). + config SLIP tristate "SLIP (serial line) support" ---help--- |