From 1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 16 Apr 2005 15:20:36 -0700 Subject: Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! --- drivers/char/riscom8.c | 1809 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 1809 insertions(+) create mode 100644 drivers/char/riscom8.c (limited to 'drivers/char/riscom8.c') diff --git a/drivers/char/riscom8.c b/drivers/char/riscom8.c new file mode 100644 index 0000000..55a3a01 --- /dev/null +++ b/drivers/char/riscom8.c @@ -0,0 +1,1809 @@ +/* + * linux/drivers/char/riscom.c -- RISCom/8 multiport serial driver. + * + * Copyright (C) 1994-1996 Dmitry Gorodchanin (pgmdsg@ibi.com) + * + * This code is loosely based on the Linux serial driver, written by + * Linus Torvalds, Theodore T'so and others. The RISCom/8 card + * programming info was obtained from various drivers for other OSes + * (FreeBSD, ISC, etc), but no source code from those drivers were + * directly included in this driver. + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + * Revision 1.1 + * + * ChangeLog: + * Arnaldo Carvalho de Melo - 27-Jun-2001 + * - get rid of check_region and several cleanups + */ + +#include + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#include "riscom8.h" +#include "riscom8_reg.h" + +/* Am I paranoid or not ? ;-) */ +#define RISCOM_PARANOIA_CHECK + +/* + * Crazy InteliCom/8 boards sometimes has swapped CTS & DSR signals. + * You can slightly speed up things by #undefing the following option, + * if you are REALLY sure that your board is correct one. + */ + +#define RISCOM_BRAIN_DAMAGED_CTS + +/* + * The following defines are mostly for testing purposes. But if you need + * some nice reporting in your syslog, you can define them also. + */ +#undef RC_REPORT_FIFO +#undef RC_REPORT_OVERRUN + + +#define RISCOM_LEGAL_FLAGS \ + (ASYNC_HUP_NOTIFY | ASYNC_SAK | ASYNC_SPLIT_TERMIOS | \ + ASYNC_SPD_HI | ASYNC_SPEED_VHI | ASYNC_SESSION_LOCKOUT | \ + ASYNC_PGRP_LOCKOUT | ASYNC_CALLOUT_NOHUP) + +#define RS_EVENT_WRITE_WAKEUP 0 + +static struct riscom_board * IRQ_to_board[16]; +static struct tty_driver *riscom_driver; +static unsigned char * tmp_buf; +static DECLARE_MUTEX(tmp_buf_sem); + +static unsigned long baud_table[] = { + 0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800, + 9600, 19200, 38400, 57600, 76800, 0, +}; + +static struct riscom_board rc_board[RC_NBOARD] = { + { + .base = RC_IOBASE1, + }, + { + .base = RC_IOBASE2, + }, + { + .base = RC_IOBASE3, + }, + { + .base = RC_IOBASE4, + }, +}; + +static struct riscom_port rc_port[RC_NBOARD * RC_NPORT]; + +/* RISCom/8 I/O ports addresses (without address translation) */ +static unsigned short rc_ioport[] = { +#if 1 + 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x09, 0x0a, 0x0b, 0x0c, +#else + 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x09, 0x0a, 0x0b, 0x0c, 0x10, + 0x11, 0x12, 0x18, 0x28, 0x31, 0x32, 0x39, 0x3a, 0x40, 0x41, 0x61, 0x62, + 0x63, 0x64, 0x6b, 0x70, 0x71, 0x78, 0x7a, 0x7b, 0x7f, 0x100, 0x101 +#endif +}; +#define RC_NIOPORT (sizeof(rc_ioport) / sizeof(rc_ioport[0])) + + +static inline int rc_paranoia_check(struct riscom_port const * port, + char *name, const char *routine) +{ +#ifdef RISCOM_PARANOIA_CHECK + static const char badmagic[] = KERN_INFO + "rc: Warning: bad riscom port magic number for device %s in %s\n"; + static const char badinfo[] = KERN_INFO + "rc: Warning: null riscom port for device %s in %s\n"; + + if (!port) { + printk(badinfo, name, routine); + return 1; + } + if (port->magic != RISCOM8_MAGIC) { + printk(badmagic, name, routine); + return 1; + } +#endif + return 0; +} + +/* + * + * Service functions for RISCom/8 driver. + * + */ + +/* Get board number from pointer */ +static inline int board_No (struct riscom_board const * bp) +{ + return bp - rc_board; +} + +/* Get port number from pointer */ +static inline int port_No (struct riscom_port const * port) +{ + return RC_PORT(port - rc_port); +} + +/* Get pointer to board from pointer to port */ +static inline struct riscom_board * port_Board(struct riscom_port const * port) +{ + return &rc_board[RC_BOARD(port - rc_port)]; +} + +/* Input Byte from CL CD180 register */ +static inline unsigned char rc_in(struct riscom_board const * bp, unsigned short reg) +{ + return inb(bp->base + RC_TO_ISA(reg)); +} + +/* Output Byte to CL CD180 register */ +static inline void rc_out(struct riscom_board const * bp, unsigned short reg, + unsigned char val) +{ + outb(val, bp->base + RC_TO_ISA(reg)); +} + +/* Wait for Channel Command Register ready */ +static inline void rc_wait_CCR(struct riscom_board const * bp) +{ + unsigned long delay; + + /* FIXME: need something more descriptive then 100000 :) */ + for (delay = 100000; delay; delay--) + if (!rc_in(bp, CD180_CCR)) + return; + + printk(KERN_INFO "rc%d: Timeout waiting for CCR.\n", board_No(bp)); +} + +/* + * RISCom/8 probe functions. + */ + +static inline int rc_request_io_range(struct riscom_board * const bp) +{ + int i; + + for (i = 0; i < RC_NIOPORT; i++) + if (!request_region(RC_TO_ISA(rc_ioport[i]) + bp->base, 1, + "RISCom/8")) { + goto out_release; + } + return 0; +out_release: + printk(KERN_INFO "rc%d: Skipping probe at 0x%03x. IO address in use.\n", + board_No(bp), bp->base); + while(--i >= 0) + release_region(RC_TO_ISA(rc_ioport[i]) + bp->base, 1); + return 1; +} + +static inline void rc_release_io_range(struct riscom_board * const bp) +{ + int i; + + for (i = 0; i < RC_NIOPORT; i++) + release_region(RC_TO_ISA(rc_ioport[i]) + bp->base, 1); +} + +/* Must be called with enabled interrupts */ +static inline void rc_long_delay(unsigned long delay) +{ + unsigned long i; + + for (i = jiffies + delay; time_after(i,jiffies); ) ; +} + +/* Reset and setup CD180 chip */ +static void __init rc_init_CD180(struct riscom_board const * bp) +{ + unsigned long flags; + + save_flags(flags); cli(); + rc_out(bp, RC_CTOUT, 0); /* Clear timeout */ + rc_wait_CCR(bp); /* Wait for CCR ready */ + rc_out(bp, CD180_CCR, CCR_HARDRESET); /* Reset CD180 chip */ + sti(); + rc_long_delay(HZ/20); /* Delay 0.05 sec */ + cli(); + rc_out(bp, CD180_GIVR, RC_ID); /* Set ID for this chip */ + rc_out(bp, CD180_GICR, 0); /* Clear all bits */ + rc_out(bp, CD180_PILR1, RC_ACK_MINT); /* Prio for modem intr */ + rc_out(bp, CD180_PILR2, RC_ACK_TINT); /* Prio for transmitter intr */ + rc_out(bp, CD180_PILR3, RC_ACK_RINT); /* Prio for receiver intr */ + + /* Setting up prescaler. We need 4 ticks per 1 ms */ + rc_out(bp, CD180_PPRH, (RC_OSCFREQ/(1000000/RISCOM_TPS)) >> 8); + rc_out(bp, CD180_PPRL, (RC_OSCFREQ/(1000000/RISCOM_TPS)) & 0xff); + + restore_flags(flags); +} + +/* Main probing routine, also sets irq. */ +static int __init rc_probe(struct riscom_board *bp) +{ + unsigned char val1, val2; + int irqs = 0; + int retries; + + bp->irq = 0; + + if (rc_request_io_range(bp)) + return 1; + + /* Are the I/O ports here ? */ + rc_out(bp, CD180_PPRL, 0x5a); + outb(0xff, 0x80); + val1 = rc_in(bp, CD180_PPRL); + rc_out(bp, CD180_PPRL, 0xa5); + outb(0x00, 0x80); + val2 = rc_in(bp, CD180_PPRL); + + if ((val1 != 0x5a) || (val2 != 0xa5)) { + printk(KERN_ERR "rc%d: RISCom/8 Board at 0x%03x not found.\n", + board_No(bp), bp->base); + goto out_release; + } + + /* It's time to find IRQ for this board */ + for (retries = 0; retries < 5 && irqs <= 0; retries++) { + irqs = probe_irq_on(); + rc_init_CD180(bp); /* Reset CD180 chip */ + rc_out(bp, CD180_CAR, 2); /* Select port 2 */ + rc_wait_CCR(bp); + rc_out(bp, CD180_CCR, CCR_TXEN); /* Enable transmitter */ + rc_out(bp, CD180_IER, IER_TXRDY); /* Enable tx empty intr */ + rc_long_delay(HZ/20); + irqs = probe_irq_off(irqs); + val1 = rc_in(bp, RC_BSR); /* Get Board Status reg */ + val2 = rc_in(bp, RC_ACK_TINT); /* ACK interrupt */ + rc_init_CD180(bp); /* Reset CD180 again */ + + if ((val1 & RC_BSR_TINT) || (val2 != (RC_ID | GIVR_IT_TX))) { + printk(KERN_ERR "rc%d: RISCom/8 Board at 0x%03x not " + "found.\n", board_No(bp), bp->base); + goto out_release; + } + } + + if (irqs <= 0) { + printk(KERN_ERR "rc%d: Can't find IRQ for RISCom/8 board " + "at 0x%03x.\n", board_No(bp), bp->base); + goto out_release; + } + bp->irq = irqs; + bp->flags |= RC_BOARD_PRESENT; + + printk(KERN_INFO "rc%d: RISCom/8 Rev. %c board detected at " + "0x%03x, IRQ %d.\n", + board_No(bp), + (rc_in(bp, CD180_GFRCR) & 0x0f) + 'A', /* Board revision */ + bp->base, bp->irq); + + return 0; +out_release: + rc_release_io_range(bp); + return 1; +} + +/* + * + * Interrupt processing routines. + * + */ + +static inline void rc_mark_event(struct riscom_port * port, int event) +{ + set_bit(event, &port->event); + schedule_work(&port->tqueue); +} + +static inline struct riscom_port * rc_get_port(struct riscom_board const * bp, + unsigned char const * what) +{ + unsigned char channel; + struct riscom_port * port; + + channel = rc_in(bp, CD180_GICR) >> GICR_CHAN_OFF; + if (channel < CD180_NCH) { + port = &rc_port[board_No(bp) * RC_NPORT + channel]; + if (port->flags & ASYNC_INITIALIZED) { + return port; + } + } + printk(KERN_ERR "rc%d: %s interrupt from invalid port %d\n", + board_No(bp), what, channel); + return NULL; +} + +static inline void rc_receive_exc(struct riscom_board const * bp) +{ + struct riscom_port *port; + struct tty_struct *tty; + unsigned char status; + unsigned char ch; + + if (!(port = rc_get_port(bp, "Receive"))) + return; + + tty = port->tty; + if (tty->flip.count >= TTY_FLIPBUF_SIZE) { + printk(KERN_WARNING "rc%d: port %d: Working around flip " + "buffer overflow.\n", + board_No(bp), port_No(port)); + return; + } + +#ifdef RC_REPORT_OVERRUN + status = rc_in(bp, CD180_RCSR); + if (status & RCSR_OE) { + port->overrun++; +#if 0 + printk(KERN_ERR "rc%d: port %d: Overrun. Total %ld overruns\n", + board_No(bp), port_No(port), port->overrun); +#endif + } + status &= port->mark_mask; +#else + status = rc_in(bp, CD180_RCSR) & port->mark_mask; +#endif + ch = rc_in(bp, CD180_RDR); + if (!status) { + return; + } + if (status & RCSR_TOUT) { + printk(KERN_WARNING "rc%d: port %d: Receiver timeout. " + "Hardware problems ?\n", + board_No(bp), port_No(port)); + return; + + } else if (status & RCSR_BREAK) { + printk(KERN_INFO "rc%d: port %d: Handling break...\n", + board_No(bp), port_No(port)); + *tty->flip.flag_buf_ptr++ = TTY_BREAK; + if (port->flags & ASYNC_SAK) + do_SAK(tty); + + } else if (status & RCSR_PE) + *tty->flip.flag_buf_ptr++ = TTY_PARITY; + + else if (status & RCSR_FE) + *tty->flip.flag_buf_ptr++ = TTY_FRAME; + + else if (status & RCSR_OE) + *tty->flip.flag_buf_ptr++ = TTY_OVERRUN; + + else + *tty->flip.flag_buf_ptr++ = 0; + + *tty->flip.char_buf_ptr++ = ch; + tty->flip.count++; + schedule_delayed_work(&tty->flip.work, 1); +} + +static inline void rc_receive(struct riscom_board const * bp) +{ + struct riscom_port *port; + struct tty_struct *tty; + unsigned char count; + + if (!(port = rc_get_port(bp, "Receive"))) + return; + + tty = port->tty; + + count = rc_in(bp, CD180_RDCR); + +#ifdef RC_REPORT_FIFO + port->hits[count > 8 ? 9 : count]++; +#endif + + while (count--) { + if (tty->flip.count >= TTY_FLIPBUF_SIZE) { + printk(KERN_WARNING "rc%d: port %d: Working around " + "flip buffer overflow.\n", + board_No(bp), port_No(port)); + break; + } + *tty->flip.char_buf_ptr++ = rc_in(bp, CD180_RDR); + *tty->flip.flag_buf_ptr++ = 0; + tty->flip.count++; + } + schedule_delayed_work(&tty->flip.work, 1); +} + +static inline void rc_transmit(struct riscom_board const * bp) +{ + struct riscom_port *port; + struct tty_struct *tty; + unsigned char count; + + + if (!(port = rc_get_port(bp, "Transmit"))) + return; + + tty = port->tty; + + if (port->IER & IER_TXEMPTY) { + /* FIFO drained */ + rc_out(bp, CD180_CAR, port_No(port)); + port->IER &= ~IER_TXEMPTY; + rc_out(bp, CD180_IER, port->IER); + return; + } + + if ((port->xmit_cnt <= 0 && !port->break_length) + || tty->stopped || tty->hw_stopped) { + rc_out(bp, CD180_CAR, port_No(port)); + port->IER &= ~IER_TXRDY; + rc_out(bp, CD180_IER, port->IER); + return; + } + + if (port->break_length) { + if (port->break_length > 0) { + if (port->COR2 & COR2_ETC) { + rc_out(bp, CD180_TDR, CD180_C_ESC); + rc_out(bp, CD180_TDR, CD180_C_SBRK); + port->COR2 &= ~COR2_ETC; + } + count = min_t(int, port->break_length, 0xff); + rc_out(bp, CD180_TDR, CD180_C_ESC); + rc_out(bp, CD180_TDR, CD180_C_DELAY); + rc_out(bp, CD180_TDR, count); + if (!(port->break_length -= count)) + port->break_length--; + } else { + rc_out(bp, CD180_TDR, CD180_C_ESC); + rc_out(bp, CD180_TDR, CD180_C_EBRK); + rc_out(bp, CD180_COR2, port->COR2); + rc_wait_CCR(bp); + rc_out(bp, CD180_CCR, CCR_CORCHG2); + port->break_length = 0; + } + return; + } + + count = CD180_NFIFO; + do { + rc_out(bp, CD180_TDR, port->xmit_buf[port->xmit_tail++]); + port->xmit_tail = port->xmit_tail & (SERIAL_XMIT_SIZE-1); + if (--port->xmit_cnt <= 0) + break; + } while (--count > 0); + + if (port->xmit_cnt <= 0) { + rc_out(bp, CD180_CAR, port_No(port)); + port->IER &= ~IER_TXRDY; + rc_out(bp, CD180_IER, port->IER); + } + if (port->xmit_cnt <= port->wakeup_chars) + rc_mark_event(port, RS_EVENT_WRITE_WAKEUP); +} + +static inline void rc_check_modem(struct riscom_board const * bp) +{ + struct riscom_port *port; + struct tty_struct *tty; + unsigned char mcr; + + if (!(port = rc_get_port(bp, "Modem"))) + return; + + tty = port->tty; + + mcr = rc_in(bp, CD180_MCR); + if (mcr & MCR_CDCHG) { + if (rc_in(bp, CD180_MSVR) & MSVR_CD) + wake_up_interruptible(&port->open_wait); + else + schedule_work(&port->tqueue_hangup); + } + +#ifdef RISCOM_BRAIN_DAMAGED_CTS + if (mcr & MCR_CTSCHG) { + if (rc_in(bp, CD180_MSVR) & MSVR_CTS) { + tty->hw_stopped = 0; + port->IER |= IER_TXRDY; + if (port->xmit_cnt <= port->wakeup_chars) + rc_mark_event(port, RS_EVENT_WRITE_WAKEUP); + } else { + tty->hw_stopped = 1; + port->IER &= ~IER_TXRDY; + } + rc_out(bp, CD180_IER, port->IER); + } + if (mcr & MCR_DSRCHG) { + if (rc_in(bp, CD180_MSVR) & MSVR_DSR) { + tty->hw_stopped = 0; + port->IER |= IER_TXRDY; + if (port->xmit_cnt <= port->wakeup_chars) + rc_mark_event(port, RS_EVENT_WRITE_WAKEUP); + } else { + tty->hw_stopped = 1; + port->IER &= ~IER_TXRDY; + } + rc_out(bp, CD180_IER, port->IER); + } +#endif /* RISCOM_BRAIN_DAMAGED_CTS */ + + /* Clear change bits */ + rc_out(bp, CD180_MCR, 0); +} + +/* The main interrupt processing routine */ +static irqreturn_t rc_interrupt(int irq, void * dev_id, struct pt_regs * regs) +{ + unsigned char status; + unsigned char ack; + struct riscom_board *bp; + unsigned long loop = 0; + int handled = 0; + + bp = IRQ_to_board[irq]; + + if (!bp || !(bp->flags & RC_BOARD_ACTIVE)) { + return IRQ_NONE; + } + + while ((++loop < 16) && ((status = ~(rc_in(bp, RC_BSR))) & + (RC_BSR_TOUT | RC_BSR_TINT | + RC_BSR_MINT | RC_BSR_RINT))) { + handled = 1; + if (status & RC_BSR_TOUT) + printk(KERN_WARNING "rc%d: Got timeout. Hardware " + "error?\n", board_No(bp)); + + else if (status & RC_BSR_RINT) { + ack = rc_in(bp, RC_ACK_RINT); + + if (ack == (RC_ID | GIVR_IT_RCV)) + rc_receive(bp); + else if (ack == (RC_ID | GIVR_IT_REXC)) + rc_receive_exc(bp); + else + printk(KERN_WARNING "rc%d: Bad receive ack " + "0x%02x.\n", + board_No(bp), ack); + + } else if (status & RC_BSR_TINT) { + ack = rc_in(bp, RC_ACK_TINT); + + if (ack == (RC_ID | GIVR_IT_TX)) + rc_transmit(bp); + else + printk(KERN_WARNING "rc%d: Bad transmit ack " + "0x%02x.\n", + board_No(bp), ack); + + } else /* if (status & RC_BSR_MINT) */ { + ack = rc_in(bp, RC_ACK_MINT); + + if (ack == (RC_ID | GIVR_IT_MODEM)) + rc_check_modem(bp); + else + printk(KERN_WARNING "rc%d: Bad modem ack " + "0x%02x.\n", + board_No(bp), ack); + + } + + rc_out(bp, CD180_EOIR, 0); /* Mark end of interrupt */ + rc_out(bp, RC_CTOUT, 0); /* Clear timeout flag */ + } + return IRQ_RETVAL(handled); +} + +/* + * Routines for open & close processing. + */ + +/* Called with disabled interrupts */ +static inline int rc_setup_board(struct riscom_board * bp) +{ + int error; + + if (bp->flags & RC_BOARD_ACTIVE) + return 0; + + error = request_irq(bp->irq, rc_interrupt, SA_INTERRUPT, + "RISCom/8", NULL); + if (error) + return error; + + rc_out(bp, RC_CTOUT, 0); /* Just in case */ + bp->DTR = ~0; + rc_out(bp, RC_DTR, bp->DTR); /* Drop DTR on all ports */ + + IRQ_to_board[bp->irq] = bp; + bp->flags |= RC_BOARD_ACTIVE; + + return 0; +} + +/* Called with disabled interrupts */ +static inline void rc_shutdown_board(struct riscom_board *bp) +{ + if (!(bp->flags & RC_BOARD_ACTIVE)) + return; + + bp->flags &= ~RC_BOARD_ACTIVE; + + free_irq(bp->irq, NULL); + IRQ_to_board[bp->irq] = NULL; + + bp->DTR = ~0; + rc_out(bp, RC_DTR, bp->DTR); /* Drop DTR on all ports */ + +} + +/* + * Setting up port characteristics. + * Must be called with disabled interrupts + */ +static void rc_change_speed(struct riscom_board *bp, struct riscom_port *port) +{ + struct tty_struct *tty; + unsigned long baud; + long tmp; + unsigned char cor1 = 0, cor3 = 0; + unsigned char mcor1 = 0, mcor2 = 0; + + if (!(tty = port->tty) || !tty->termios) + return; + + port->IER = 0; + port->COR2 = 0; + port->MSVR = MSVR_RTS; + + baud = C_BAUD(tty); + + if (baud & CBAUDEX) { + baud &= ~CBAUDEX; + if (baud < 1 || baud > 2) + port->tty->termios->c_cflag &= ~CBAUDEX; + else + baud += 15; + } + if (baud == 15) { + if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI) + baud ++; + if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI) + baud += 2; + } + + /* Select port on the board */ + rc_out(bp, CD180_CAR, port_No(port)); + + if (!baud_table[baud]) { + /* Drop DTR & exit */ + bp->DTR |= (1u << port_No(port)); + rc_out(bp, RC_DTR, bp->DTR); + return; + } else { + /* Set DTR on */ + bp->DTR &= ~(1u << port_No(port)); + rc_out(bp, RC_DTR, bp->DTR); + } + + /* + * Now we must calculate some speed depended things + */ + + /* Set baud rate for port */ + tmp = (((RC_OSCFREQ + baud_table[baud]/2) / baud_table[baud] + + CD180_TPC/2) / CD180_TPC); + + rc_out(bp, CD180_RBPRH, (tmp >> 8) & 0xff); + rc_out(bp, CD180_TBPRH, (tmp >> 8) & 0xff); + rc_out(bp, CD180_RBPRL, tmp & 0xff); + rc_out(bp, CD180_TBPRL, tmp & 0xff); + + baud = (baud_table[baud] + 5) / 10; /* Estimated CPS */ + + /* Two timer ticks seems enough to wakeup something like SLIP driver */ + tmp = ((baud + HZ/2) / HZ) * 2 - CD180_NFIFO; + port->wakeup_chars = (tmp < 0) ? 0 : ((tmp >= SERIAL_XMIT_SIZE) ? + SERIAL_XMIT_SIZE - 1 : tmp); + + /* Receiver timeout will be transmission time for 1.5 chars */ + tmp = (RISCOM_TPS + RISCOM_TPS/2 + baud/2) / baud; + tmp = (tmp > 0xff) ? 0xff : tmp; + rc_out(bp, CD180_RTPR, tmp); + + switch (C_CSIZE(tty)) { + case CS5: + cor1 |= COR1_5BITS; + break; + case CS6: + cor1 |= COR1_6BITS; + break; + case CS7: + cor1 |= COR1_7BITS; + break; + case CS8: + cor1 |= COR1_8BITS; + break; + } + + if (C_CSTOPB(tty)) + cor1 |= COR1_2SB; + + cor1 |= COR1_IGNORE; + if (C_PARENB(tty)) { + cor1 |= COR1_NORMPAR; + if (C_PARODD(tty)) + cor1 |= COR1_ODDP; + if (I_INPCK(tty)) + cor1 &= ~COR1_IGNORE; + } + /* Set marking of some errors */ + port->mark_mask = RCSR_OE | RCSR_TOUT; + if (I_INPCK(tty)) + port->mark_mask |= RCSR_FE | RCSR_PE; + if (I_BRKINT(tty) || I_PARMRK(tty)) + port->mark_mask |= RCSR_BREAK; + if (I_IGNPAR(tty)) + port->mark_mask &= ~(RCSR_FE | RCSR_PE); + if (I_IGNBRK(tty)) { + port->mark_mask &= ~RCSR_BREAK; + if (I_IGNPAR(tty)) + /* Real raw mode. Ignore all */ + port->mark_mask &= ~RCSR_OE; + } + /* Enable Hardware Flow Control */ + if (C_CRTSCTS(tty)) { +#ifdef RISCOM_BRAIN_DAMAGED_CTS + port->IER |= IER_DSR | IER_CTS; + mcor1 |= MCOR1_DSRZD | MCOR1_CTSZD; + mcor2 |= MCOR2_DSROD | MCOR2_CTSOD; + tty->hw_stopped = !(rc_in(bp, CD180_MSVR) & (MSVR_CTS|MSVR_DSR)); +#else + port->COR2 |= COR2_CTSAE; +#endif + } + /* Enable Software Flow Control. FIXME: I'm not sure about this */ + /* Some people reported that it works, but I still doubt */ + if (I_IXON(tty)) { + port->COR2 |= COR2_TXIBE; + cor3 |= (COR3_FCT | COR3_SCDE); + if (I_IXANY(tty)) + port->COR2 |= COR2_IXM; + rc_out(bp, CD180_SCHR1, START_CHAR(tty)); + rc_out(bp, CD180_SCHR2, STOP_CHAR(tty)); + rc_out(bp, CD180_SCHR3, START_CHAR(tty)); + rc_out(bp, CD180_SCHR4, STOP_CHAR(tty)); + } + if (!C_CLOCAL(tty)) { + /* Enable CD check */ + port->IER |= IER_CD; + mcor1 |= MCOR1_CDZD; + mcor2 |= MCOR2_CDOD; + } + + if (C_CREAD(tty)) + /* Enable receiver */ + port->IER |= IER_RXD; + + /* Set input FIFO size (1-8 bytes) */ + cor3 |= RISCOM_RXFIFO; + /* Setting up CD180 channel registers */ + rc_out(bp, CD180_COR1, cor1); + rc_out(bp, CD180_COR2, port->COR2); + rc_out(bp, CD180_COR3, cor3); + /* Make CD180 know about registers change */ + rc_wait_CCR(bp); + rc_out(bp, CD180_CCR, CCR_CORCHG1 | CCR_CORCHG2 | CCR_CORCHG3); + /* Setting up modem option registers */ + rc_out(bp, CD180_MCOR1, mcor1); + rc_out(bp, CD180_MCOR2, mcor2); + /* Enable CD180 transmitter & receiver */ + rc_wait_CCR(bp); + rc_out(bp, CD180_CCR, CCR_TXEN | CCR_RXEN); + /* Enable interrupts */ + rc_out(bp, CD180_IER, port->IER); + /* And finally set RTS on */ + rc_out(bp, CD180_MSVR, port->MSVR); +} + +/* Must be called with interrupts enabled */ +static int rc_setup_port(struct riscom_board *bp, struct riscom_port *port) +{ + unsigned long flags; + + if (port->flags & ASYNC_INITIALIZED) + return 0; + + if (!port->xmit_buf) { + /* We may sleep in get_zeroed_page() */ + unsigned long tmp; + + if (!(tmp = get_zeroed_page(GFP_KERNEL))) + return -ENOMEM; + + if (port->xmit_buf) { + free_page(tmp); + return -ERESTARTSYS; + } + port->xmit_buf = (unsigned char *) tmp; + } + + save_flags(flags); cli(); + + if (port->tty) + clear_bit(TTY_IO_ERROR, &port->tty->flags); + + if (port->count == 1) + bp->count++; + + port->xmit_cnt = port->xmit_head = port->xmit_tail = 0; + rc_change_speed(bp, port); + port->flags |= ASYNC_INITIALIZED; + + restore_flags(flags); + return 0; +} + +/* Must be called with interrupts disabled */ +static void rc_shutdown_port(struct riscom_board *bp, struct riscom_port *port) +{ + struct tty_struct *tty; + + if (!(port->flags & ASYNC_INITIALIZED)) + return; + +#ifdef RC_REPORT_OVERRUN + printk(KERN_INFO "rc%d: port %d: Total %ld overruns were detected.\n", + board_No(bp), port_No(port), port->overrun); +#endif +#ifdef RC_REPORT_FIFO + { + int i; + + printk(KERN_INFO "rc%d: port %d: FIFO hits [ ", + board_No(bp), port_No(port)); + for (i = 0; i < 10; i++) { + printk("%ld ", port->hits[i]); + } + printk("].\n"); + } +#endif + if (port->xmit_buf) { + free_page((unsigned long) port->xmit_buf); + port->xmit_buf = NULL; + } + + if (!(tty = port->tty) || C_HUPCL(tty)) { + /* Drop DTR */ + bp->DTR |= (1u << port_No(port)); + rc_out(bp, RC_DTR, bp->DTR); + } + + /* Select port */ + rc_out(bp, CD180_CAR, port_No(port)); + /* Reset port */ + rc_wait_CCR(bp); + rc_out(bp, CD180_CCR, CCR_SOFTRESET); + /* Disable all interrupts from this port */ + port->IER = 0; + rc_out(bp, CD180_IER, port->IER); + + if (tty) + set_bit(TTY_IO_ERROR, &tty->flags); + port->flags &= ~ASYNC_INITIALIZED; + + if (--bp->count < 0) { + printk(KERN_INFO "rc%d: rc_shutdown_port: " + "bad board count: %d\n", + board_No(bp), bp->count); + bp->count = 0; + } + + /* + * If this is the last opened port on the board + * shutdown whole board + */ + if (!bp->count) + rc_shutdown_board(bp); +} + + +static int block_til_ready(struct tty_struct *tty, struct file * filp, + struct riscom_port *port) +{ + DECLARE_WAITQUEUE(wait, current); + struct riscom_board *bp = port_Board(port); + int retval; + int do_clocal = 0; + int CD; + + /* + * If the device is in the middle of being closed, then block + * until it's done, and then try again. + */ + if (tty_hung_up_p(filp) || port->flags & ASYNC_CLOSING) { + interruptible_sleep_on(&port->close_wait); + if (port->flags & ASYNC_HUP_NOTIFY) + return -EAGAIN; + else + return -ERESTARTSYS; + } + + /* + * If non-blocking mode is set, or the port is not enabled, + * then make the check up front and then exit. + */ + if ((filp->f_flags & O_NONBLOCK) || + (tty->flags & (1 << TTY_IO_ERROR))) { + port->flags |= ASYNC_NORMAL_ACTIVE; + return 0; + } + + if (C_CLOCAL(tty)) + do_clocal = 1; + + /* + * Block waiting for the carrier detect and the line to become + * free (i.e., not in use by the callout). While we are in + * this loop, info->count is dropped by one, so that + * rs_close() knows when to free things. We restore it upon + * exit, either normal or abnormal. + */ + retval = 0; + add_wait_queue(&port->open_wait, &wait); + cli(); + if (!tty_hung_up_p(filp)) + port->count--; + sti(); + port->blocked_open++; + while (1) { + cli(); + rc_out(bp, CD180_CAR, port_No(port)); + CD = rc_in(bp, CD180_MSVR) & MSVR_CD; + rc_out(bp, CD180_MSVR, MSVR_RTS); + bp->DTR &= ~(1u << port_No(port)); + rc_out(bp, RC_DTR, bp->DTR); + sti(); + set_current_state(TASK_INTERRUPTIBLE); + if (tty_hung_up_p(filp) || + !(port->flags & ASYNC_INITIALIZED)) { + if (port->flags & ASYNC_HUP_NOTIFY) + retval = -EAGAIN; + else + retval = -ERESTARTSYS; + break; + } + if (!(port->flags & ASYNC_CLOSING) && + (do_clocal || CD)) + break; + if (signal_pending(current)) { + retval = -ERESTARTSYS; + break; + } + schedule(); + } + current->state = TASK_RUNNING; + remove_wait_queue(&port->open_wait, &wait); + if (!tty_hung_up_p(filp)) + port->count++; + port->blocked_open--; + if (retval) + return retval; + + port->flags |= ASYNC_NORMAL_ACTIVE; + return 0; +} + +static int rc_open(struct tty_struct * tty, struct file * filp) +{ + int board; + int error; + struct riscom_port * port; + struct riscom_board * bp; + + board = RC_BOARD(tty->index); + if (board >= RC_NBOARD || !(rc_board[board].flags & RC_BOARD_PRESENT)) + return -ENODEV; + + bp = &rc_board[board]; + port = rc_port + board * RC_NPORT + RC_PORT(tty->index); + if (rc_paranoia_check(port, tty->name, "rc_open")) + return -ENODEV; + + if ((error = rc_setup_board(bp))) + return error; + + port->count++; + tty->driver_data = port; + port->tty = tty; + + if ((error = rc_setup_port(bp, port))) + return error; + + if ((error = block_til_ready(tty, filp, port))) + return error; + + return 0; +} + +static void rc_close(struct tty_struct * tty, struct file * filp) +{ + struct riscom_port *port = (struct riscom_port *) tty->driver_data; + struct riscom_board *bp; + unsigned long flags; + unsigned long timeout; + + if (!port || rc_paranoia_check(port, tty->name, "close")) + return; + + save_flags(flags); cli(); + if (tty_hung_up_p(filp)) + goto out; + + bp = port_Board(port); + if ((tty->count == 1) && (port->count != 1)) { + printk(KERN_INFO "rc%d: rc_close: bad port count;" + " tty->count is 1, port count is %d\n", + board_No(bp), port->count); + port->count = 1; + } + if (--port->count < 0) { + printk(KERN_INFO "rc%d: rc_close: bad port count " + "for tty%d: %d\n", + board_No(bp), port_No(port), port->count); + port->count = 0; + } + if (port->count) + goto out; + port->flags |= ASYNC_CLOSING; + /* + * Now we wait for the transmit buffer to clear; and we notify + * the line discipline to only process XON/XOFF characters. + */ + tty->closing = 1; + if (port->closing_wait != ASYNC_CLOSING_WAIT_NONE) + tty_wait_until_sent(tty, port->closing_wait); + /* + * At this point we stop accepting input. To do this, we + * disable the receive line status interrupts, and tell the + * interrupt driver to stop checking the data ready bit in the + * line status register. + */ + port->IER &= ~IER_RXD; + if (port->flags & ASYNC_INITIALIZED) { + port->IER &= ~IER_TXRDY; + port->IER |= IER_TXEMPTY; + rc_out(bp, CD180_CAR, port_No(port)); + rc_out(bp, CD180_IER, port->IER); + /* + * Before we drop DTR, make sure the UART transmitter + * has completely drained; this is especially + * important if there is a transmit FIFO! + */ + timeout = jiffies+HZ; + while(port->IER & IER_TXEMPTY) { + msleep_interruptible(jiffies_to_msecs(port->timeout)); + if (time_after(jiffies, timeout)) + break; + } + } + rc_shutdown_port(bp, port); + if (tty->driver->flush_buffer) + tty->driver->flush_buffer(tty); + tty_ldisc_flush(tty); + + tty->closing = 0; + port->event = 0; + port->tty = NULL; + if (port->blocked_open) { + if (port->close_delay) { + msleep_interruptible(jiffies_to_msecs(port->close_delay)); + } + wake_up_interruptible(&port->open_wait); + } + port->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING); + wake_up_interruptible(&port->close_wait); +out: restore_flags(flags); +} + +static int rc_write(struct tty_struct * tty, + const unsigned char *buf, int count) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + struct riscom_board *bp; + int c, total = 0; + unsigned long flags; + + if (rc_paranoia_check(port, tty->name, "rc_write")) + return 0; + + bp = port_Board(port); + + if (!tty || !port->xmit_buf || !tmp_buf) + return 0; + + save_flags(flags); + while (1) { + cli(); + c = min_t(int, count, min(SERIAL_XMIT_SIZE - port->xmit_cnt - 1, + SERIAL_XMIT_SIZE - port->xmit_head)); + if (c <= 0) { + restore_flags(flags); + break; + } + + memcpy(port->xmit_buf + port->xmit_head, buf, c); + port->xmit_head = (port->xmit_head + c) & (SERIAL_XMIT_SIZE-1); + port->xmit_cnt += c; + restore_flags(flags); + + buf += c; + count -= c; + total += c; + } + + cli(); + if (port->xmit_cnt && !tty->stopped && !tty->hw_stopped && + !(port->IER & IER_TXRDY)) { + port->IER |= IER_TXRDY; + rc_out(bp, CD180_CAR, port_No(port)); + rc_out(bp, CD180_IER, port->IER); + } + restore_flags(flags); + + return total; +} + +static void rc_put_char(struct tty_struct * tty, unsigned char ch) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + unsigned long flags; + + if (rc_paranoia_check(port, tty->name, "rc_put_char")) + return; + + if (!tty || !port->xmit_buf) + return; + + save_flags(flags); cli(); + + if (port->xmit_cnt >= SERIAL_XMIT_SIZE - 1) + goto out; + + port->xmit_buf[port->xmit_head++] = ch; + port->xmit_head &= SERIAL_XMIT_SIZE - 1; + port->xmit_cnt++; +out: restore_flags(flags); +} + +static void rc_flush_chars(struct tty_struct * tty) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + unsigned long flags; + + if (rc_paranoia_check(port, tty->name, "rc_flush_chars")) + return; + + if (port->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped || + !port->xmit_buf) + return; + + save_flags(flags); cli(); + port->IER |= IER_TXRDY; + rc_out(port_Board(port), CD180_CAR, port_No(port)); + rc_out(port_Board(port), CD180_IER, port->IER); + restore_flags(flags); +} + +static int rc_write_room(struct tty_struct * tty) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + int ret; + + if (rc_paranoia_check(port, tty->name, "rc_write_room")) + return 0; + + ret = SERIAL_XMIT_SIZE - port->xmit_cnt - 1; + if (ret < 0) + ret = 0; + return ret; +} + +static int rc_chars_in_buffer(struct tty_struct *tty) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + + if (rc_paranoia_check(port, tty->name, "rc_chars_in_buffer")) + return 0; + + return port->xmit_cnt; +} + +static void rc_flush_buffer(struct tty_struct *tty) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + unsigned long flags; + + if (rc_paranoia_check(port, tty->name, "rc_flush_buffer")) + return; + + save_flags(flags); cli(); + port->xmit_cnt = port->xmit_head = port->xmit_tail = 0; + restore_flags(flags); + + wake_up_interruptible(&tty->write_wait); + tty_wakeup(tty); +} + +static int rc_tiocmget(struct tty_struct *tty, struct file *file) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + struct riscom_board * bp; + unsigned char status; + unsigned int result; + unsigned long flags; + + if (rc_paranoia_check(port, tty->name, __FUNCTION__)) + return -ENODEV; + + bp = port_Board(port); + save_flags(flags); cli(); + rc_out(bp, CD180_CAR, port_No(port)); + status = rc_in(bp, CD180_MSVR); + result = rc_in(bp, RC_RI) & (1u << port_No(port)) ? 0 : TIOCM_RNG; + restore_flags(flags); + result |= ((status & MSVR_RTS) ? TIOCM_RTS : 0) + | ((status & MSVR_DTR) ? TIOCM_DTR : 0) + | ((status & MSVR_CD) ? TIOCM_CAR : 0) + | ((status & MSVR_DSR) ? TIOCM_DSR : 0) + | ((status & MSVR_CTS) ? TIOCM_CTS : 0); + return result; +} + +static int rc_tiocmset(struct tty_struct *tty, struct file *file, + unsigned int set, unsigned int clear) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + unsigned long flags; + struct riscom_board *bp; + + if (rc_paranoia_check(port, tty->name, __FUNCTION__)) + return -ENODEV; + + bp = port_Board(port); + + save_flags(flags); cli(); + if (set & TIOCM_RTS) + port->MSVR |= MSVR_RTS; + if (set & TIOCM_DTR) + bp->DTR &= ~(1u << port_No(port)); + + if (clear & TIOCM_RTS) + port->MSVR &= ~MSVR_RTS; + if (clear & TIOCM_DTR) + bp->DTR |= (1u << port_No(port)); + + rc_out(bp, CD180_CAR, port_No(port)); + rc_out(bp, CD180_MSVR, port->MSVR); + rc_out(bp, RC_DTR, bp->DTR); + restore_flags(flags); + return 0; +} + +static inline void rc_send_break(struct riscom_port * port, unsigned long length) +{ + struct riscom_board *bp = port_Board(port); + unsigned long flags; + + save_flags(flags); cli(); + port->break_length = RISCOM_TPS / HZ * length; + port->COR2 |= COR2_ETC; + port->IER |= IER_TXRDY; + rc_out(bp, CD180_CAR, port_No(port)); + rc_out(bp, CD180_COR2, port->COR2); + rc_out(bp, CD180_IER, port->IER); + rc_wait_CCR(bp); + rc_out(bp, CD180_CCR, CCR_CORCHG2); + rc_wait_CCR(bp); + restore_flags(flags); +} + +static inline int rc_set_serial_info(struct riscom_port * port, + struct serial_struct __user * newinfo) +{ + struct serial_struct tmp; + struct riscom_board *bp = port_Board(port); + int change_speed; + unsigned long flags; + + if (copy_from_user(&tmp, newinfo, sizeof(tmp))) + return -EFAULT; + +#if 0 + if ((tmp.irq != bp->irq) || + (tmp.port != bp->base) || + (tmp.type != PORT_CIRRUS) || + (tmp.baud_base != (RC_OSCFREQ + CD180_TPC/2) / CD180_TPC) || + (tmp.custom_divisor != 0) || + (tmp.xmit_fifo_size != CD180_NFIFO) || + (tmp.flags & ~RISCOM_LEGAL_FLAGS)) + return -EINVAL; +#endif + + change_speed = ((port->flags & ASYNC_SPD_MASK) != + (tmp.flags & ASYNC_SPD_MASK)); + + if (!capable(CAP_SYS_ADMIN)) { + if ((tmp.close_delay != port->close_delay) || + (tmp.closing_wait != port->closing_wait) || + ((tmp.flags & ~ASYNC_USR_MASK) != + (port->flags & ~ASYNC_USR_MASK))) + return -EPERM; + port->flags = ((port->flags & ~ASYNC_USR_MASK) | + (tmp.flags & ASYNC_USR_MASK)); + } else { + port->flags = ((port->flags & ~ASYNC_FLAGS) | + (tmp.flags & ASYNC_FLAGS)); + port->close_delay = tmp.close_delay; + port->closing_wait = tmp.closing_wait; + } + if (change_speed) { + save_flags(flags); cli(); + rc_change_speed(bp, port); + restore_flags(flags); + } + return 0; +} + +static inline int rc_get_serial_info(struct riscom_port * port, + struct serial_struct __user *retinfo) +{ + struct serial_struct tmp; + struct riscom_board *bp = port_Board(port); + + memset(&tmp, 0, sizeof(tmp)); + tmp.type = PORT_CIRRUS; + tmp.line = port - rc_port; + tmp.port = bp->base; + tmp.irq = bp->irq; + tmp.flags = port->flags; + tmp.baud_base = (RC_OSCFREQ + CD180_TPC/2) / CD180_TPC; + tmp.close_delay = port->close_delay * HZ/100; + tmp.closing_wait = port->closing_wait * HZ/100; + tmp.xmit_fifo_size = CD180_NFIFO; + return copy_to_user(retinfo, &tmp, sizeof(tmp)) ? -EFAULT : 0; +} + +static int rc_ioctl(struct tty_struct * tty, struct file * filp, + unsigned int cmd, unsigned long arg) + +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + void __user *argp = (void __user *)arg; + int retval; + + if (rc_paranoia_check(port, tty->name, "rc_ioctl")) + return -ENODEV; + + switch (cmd) { + case TCSBRK: /* SVID version: non-zero arg --> no break */ + retval = tty_check_change(tty); + if (retval) + return retval; + tty_wait_until_sent(tty, 0); + if (!arg) + rc_send_break(port, HZ/4); /* 1/4 second */ + break; + case TCSBRKP: /* support for POSIX tcsendbreak() */ + retval = tty_check_change(tty); + if (retval) + return retval; + tty_wait_until_sent(tty, 0); + rc_send_break(port, arg ? arg*(HZ/10) : HZ/4); + break; + case TIOCGSOFTCAR: + return put_user(C_CLOCAL(tty) ? 1 : 0, (unsigned __user *)argp); + case TIOCSSOFTCAR: + if (get_user(arg,(unsigned __user *) argp)) + return -EFAULT; + tty->termios->c_cflag = + ((tty->termios->c_cflag & ~CLOCAL) | + (arg ? CLOCAL : 0)); + break; + case TIOCGSERIAL: + return rc_get_serial_info(port, argp); + case TIOCSSERIAL: + return rc_set_serial_info(port, argp); + default: + return -ENOIOCTLCMD; + } + return 0; +} + +static void rc_throttle(struct tty_struct * tty) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + struct riscom_board *bp; + unsigned long flags; + + if (rc_paranoia_check(port, tty->name, "rc_throttle")) + return; + + bp = port_Board(port); + + save_flags(flags); cli(); + port->MSVR &= ~MSVR_RTS; + rc_out(bp, CD180_CAR, port_No(port)); + if (I_IXOFF(tty)) { + rc_wait_CCR(bp); + rc_out(bp, CD180_CCR, CCR_SSCH2); + rc_wait_CCR(bp); + } + rc_out(bp, CD180_MSVR, port->MSVR); + restore_flags(flags); +} + +static void rc_unthrottle(struct tty_struct * tty) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + struct riscom_board *bp; + unsigned long flags; + + if (rc_paranoia_check(port, tty->name, "rc_unthrottle")) + return; + + bp = port_Board(port); + + save_flags(flags); cli(); + port->MSVR |= MSVR_RTS; + rc_out(bp, CD180_CAR, port_No(port)); + if (I_IXOFF(tty)) { + rc_wait_CCR(bp); + rc_out(bp, CD180_CCR, CCR_SSCH1); + rc_wait_CCR(bp); + } + rc_out(bp, CD180_MSVR, port->MSVR); + restore_flags(flags); +} + +static void rc_stop(struct tty_struct * tty) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + struct riscom_board *bp; + unsigned long flags; + + if (rc_paranoia_check(port, tty->name, "rc_stop")) + return; + + bp = port_Board(port); + + save_flags(flags); cli(); + port->IER &= ~IER_TXRDY; + rc_out(bp, CD180_CAR, port_No(port)); + rc_out(bp, CD180_IER, port->IER); + restore_flags(flags); +} + +static void rc_start(struct tty_struct * tty) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + struct riscom_board *bp; + unsigned long flags; + + if (rc_paranoia_check(port, tty->name, "rc_start")) + return; + + bp = port_Board(port); + + save_flags(flags); cli(); + if (port->xmit_cnt && port->xmit_buf && !(port->IER & IER_TXRDY)) { + port->IER |= IER_TXRDY; + rc_out(bp, CD180_CAR, port_No(port)); + rc_out(bp, CD180_IER, port->IER); + } + restore_flags(flags); +} + +/* + * This routine is called from the work queue when the interrupt + * routine has signalled that a hangup has occurred. The path of + * hangup processing is: + * + * serial interrupt routine -> (workqueue) -> + * do_rc_hangup() -> tty->hangup() -> rc_hangup() + * + */ +static void do_rc_hangup(void *private_) +{ + struct riscom_port *port = (struct riscom_port *) private_; + struct tty_struct *tty; + + tty = port->tty; + if (tty) + tty_hangup(tty); /* FIXME: module removal race still here */ +} + +static void rc_hangup(struct tty_struct * tty) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + struct riscom_board *bp; + + if (rc_paranoia_check(port, tty->name, "rc_hangup")) + return; + + bp = port_Board(port); + + rc_shutdown_port(bp, port); + port->event = 0; + port->count = 0; + port->flags &= ~ASYNC_NORMAL_ACTIVE; + port->tty = NULL; + wake_up_interruptible(&port->open_wait); +} + +static void rc_set_termios(struct tty_struct * tty, struct termios * old_termios) +{ + struct riscom_port *port = (struct riscom_port *)tty->driver_data; + unsigned long flags; + + if (rc_paranoia_check(port, tty->name, "rc_set_termios")) + return; + + if (tty->termios->c_cflag == old_termios->c_cflag && + tty->termios->c_iflag == old_termios->c_iflag) + return; + + save_flags(flags); cli(); + rc_change_speed(port_Board(port), port); + restore_flags(flags); + + if ((old_termios->c_cflag & CRTSCTS) && + !(tty->termios->c_cflag & CRTSCTS)) { + tty->hw_stopped = 0; + rc_start(tty); + } +} + +static void do_softint(void *private_) +{ + struct riscom_port *port = (struct riscom_port *) private_; + struct tty_struct *tty; + + if(!(tty = port->tty)) + return; + + if (test_and_clear_bit(RS_EVENT_WRITE_WAKEUP, &port->event)) { + tty_wakeup(tty); + wake_up_interruptible(&tty->write_wait); + } +} + +static struct tty_operations riscom_ops = { + .open = rc_open, + .close = rc_close, + .write = rc_write, + .put_char = rc_put_char, + .flush_chars = rc_flush_chars, + .write_room = rc_write_room, + .chars_in_buffer = rc_chars_in_buffer, + .flush_buffer = rc_flush_buffer, + .ioctl = rc_ioctl, + .throttle = rc_throttle, + .unthrottle = rc_unthrottle, + .set_termios = rc_set_termios, + .stop = rc_stop, + .start = rc_start, + .hangup = rc_hangup, + .tiocmget = rc_tiocmget, + .tiocmset = rc_tiocmset, +}; + +static inline int rc_init_drivers(void) +{ + int error; + int i; + + riscom_driver = alloc_tty_driver(RC_NBOARD * RC_NPORT); + if (!riscom_driver) + return -ENOMEM; + + if (!(tmp_buf = (unsigned char *) get_zeroed_page(GFP_KERNEL))) { + printk(KERN_ERR "rc: Couldn't get free page.\n"); + put_tty_driver(riscom_driver); + return 1; + } + memset(IRQ_to_board, 0, sizeof(IRQ_to_board)); + riscom_driver->owner = THIS_MODULE; + riscom_driver->name = "ttyL"; + riscom_driver->devfs_name = "tts/L"; + riscom_driver->major = RISCOM8_NORMAL_MAJOR; + riscom_driver->type = TTY_DRIVER_TYPE_SERIAL; + riscom_driver->subtype = SERIAL_TYPE_NORMAL; + riscom_driver->init_termios = tty_std_termios; + riscom_driver->init_termios.c_cflag = + B9600 | CS8 | CREAD | HUPCL | CLOCAL; + riscom_driver->flags = TTY_DRIVER_REAL_RAW; + tty_set_operations(riscom_driver, &riscom_ops); + if ((error = tty_register_driver(riscom_driver))) { + free_page((unsigned long)tmp_buf); + put_tty_driver(riscom_driver); + printk(KERN_ERR "rc: Couldn't register RISCom/8 driver, " + "error = %d\n", + error); + return 1; + } + + memset(rc_port, 0, sizeof(rc_port)); + for (i = 0; i < RC_NPORT * RC_NBOARD; i++) { + rc_port[i].magic = RISCOM8_MAGIC; + INIT_WORK(&rc_port[i].tqueue, do_softint, &rc_port[i]); + INIT_WORK(&rc_port[i].tqueue_hangup, do_rc_hangup, &rc_port[i]); + rc_port[i].close_delay = 50 * HZ/100; + rc_port[i].closing_wait = 3000 * HZ/100; + init_waitqueue_head(&rc_port[i].open_wait); + init_waitqueue_head(&rc_port[i].close_wait); + } + + return 0; +} + +static void rc_release_drivers(void) +{ + unsigned long flags; + + save_flags(flags); + cli(); + free_page((unsigned long)tmp_buf); + tty_unregister_driver(riscom_driver); + put_tty_driver(riscom_driver); + restore_flags(flags); +} + +#ifndef MODULE +/* + * Called at boot time. + * + * You can specify IO base for up to RC_NBOARD cards, + * using line "riscom8=0xiobase1,0xiobase2,.." at LILO prompt. + * Note that there will be no probing at default + * addresses in this case. + * + */ +static int __init riscom8_setup(char *str) +{ + int ints[RC_NBOARD]; + int i; + + str = get_options(str, ARRAY_SIZE(ints), ints); + + for (i = 0; i < RC_NBOARD; i++) { + if (i < ints[0]) + rc_board[i].base = ints[i+1]; + else + rc_board[i].base = 0; + } + return 1; +} + +__setup("riscom8=", riscom8_setup); +#endif + +static char banner[] __initdata = + KERN_INFO "rc: SDL RISCom/8 card driver v1.1, (c) D.Gorodchanin " + "1994-1996.\n"; +static char no_boards_msg[] __initdata = + KERN_INFO "rc: No RISCom/8 boards detected.\n"; + +/* + * This routine must be called by kernel at boot time + */ +static int __init riscom8_init(void) +{ + int i; + int found = 0; + + printk(banner); + + if (rc_init_drivers()) + return -EIO; + + for (i = 0; i < RC_NBOARD; i++) + if (rc_board[i].base && !rc_probe(&rc_board[i])) + found++; + + if (!found) { + rc_release_drivers(); + printk(no_boards_msg); + return -EIO; + } + return 0; +} + +#ifdef MODULE +static int iobase; +static int iobase1; +static int iobase2; +static int iobase3; +MODULE_PARM(iobase, "i"); +MODULE_PARM(iobase1, "i"); +MODULE_PARM(iobase2, "i"); +MODULE_PARM(iobase3, "i"); + +MODULE_LICENSE("GPL"); +#endif /* MODULE */ + +/* + * You can setup up to 4 boards (current value of RC_NBOARD) + * by specifying "iobase=0xXXX iobase1=0xXXX ..." as insmod parameter. + * + */ +static int __init riscom8_init_module (void) +{ +#ifdef MODULE + int i; + + if (iobase || iobase1 || iobase2 || iobase3) { + for(i = 0; i < RC_NBOARD; i++) + rc_board[0].base = 0; + } + + if (iobase) + rc_board[0].base = iobase; + if (iobase1) + rc_board[1].base = iobase1; + if (iobase2) + rc_board[2].base = iobase2; + if (iobase3) + rc_board[3].base = iobase3; +#endif /* MODULE */ + + return riscom8_init(); +} + +static void __exit riscom8_exit_module (void) +{ + int i; + + rc_release_drivers(); + for (i = 0; i < RC_NBOARD; i++) + if (rc_board[i].flags & RC_BOARD_PRESENT) + rc_release_io_range(&rc_board[i]); + +} + +module_init(riscom8_init_module); +module_exit(riscom8_exit_module); + -- cgit v1.1