From 4efefd1d8ea4eaf71bacc4f71fa017c202fa67ec Mon Sep 17 00:00:00 2001 From: Christian Trefzer Date: Mon, 26 Jun 2006 00:26:55 -0700 Subject: [PATCH] neofb: fix unblank logic interfering with lid toggled backlight This is a fix for the most annoying problem that remained with neofb: After "setterm -powersave powerdown" the console blanker will disable the backlight after the given timeout expires. If this happens after the lid has been shut, we read "LCD off" from the register and store that in the driver. Once the lid is opened, the backlight turns on, but any key press that would awaken the blanked console will switch the backlight off again. The workaround so far was to use the "display config toggle" Fn key combo - once if no external display is attached, otherwise as often as required to restore the desired display setup. The following patch fixes the issue at least for the LCD-only case, with no external monitor attached. Other display setup permutations are pending further testing, but so far I can guarantee at least no negative change in behaviour, if any at all. Signed-off-by: Christian Trefzer Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/neofb.c | 32 +++++++++++++++++++++++--------- 1 file changed, 23 insertions(+), 9 deletions(-) (limited to 'drivers/video') diff --git a/drivers/video/neofb.c b/drivers/video/neofb.c index 24b12f7..2f156b7 100644 --- a/drivers/video/neofb.c +++ b/drivers/video/neofb.c @@ -1333,17 +1333,22 @@ static int neofb_blank(int blank_mode, struct fb_info *info) * run "setterm -powersave powerdown" to take advantage */ struct neofb_par *par = info->par; - int seqflags, lcdflags, dpmsflags, reg; - + int seqflags, lcdflags, dpmsflags, reg, tmpdisp; /* - * Reload the value stored in the register, if sensible. It might have - * been changed via FN keystroke. + * Read back the register bits related to display configuration. They might + * have been changed underneath the driver via Fn key stroke. + */ + neoUnlock(); + tmpdisp = vga_rgfx(NULL, 0x20) & 0x03; + neoLock(&par->state); + + /* In case we blank the screen, we want to store the possibly new + * configuration in the driver. During un-blank, we re-apply this setting, + * since the LCD bit will be cleared in order to switch off the backlight. */ if (par->PanelDispCntlRegRead) { - neoUnlock(); - par->PanelDispCntlReg1 = vga_rgfx(NULL, 0x20) & 0x03; - neoLock(&par->state); + par->PanelDispCntlReg1 = tmpdisp; } par->PanelDispCntlRegRead = !blank_mode; @@ -1378,12 +1383,21 @@ static int neofb_blank(int blank_mode, struct fb_info *info) break; case FB_BLANK_NORMAL: /* just blank screen (backlight stays on) */ seqflags = VGA_SR01_SCREEN_OFF; /* Disable sequencer */ - lcdflags = par->PanelDispCntlReg1 & 0x02; /* LCD normal */ + /* + * During a blank operation with the LID shut, we might store "LCD off" + * by mistake. Due to timing issues, the BIOS may switch the lights + * back on, and we turn it back off once we "unblank". + * + * So here is an attempt to implement ">=" - if we are in the process + * of unblanking, and the LCD bit is unset in the driver but set in the + * register, we must keep it. + */ + lcdflags = ((par->PanelDispCntlReg1 | tmpdisp) & 0x02); /* LCD normal */ dpmsflags = 0x00; /* no hsync/vsync suppression */ break; case FB_BLANK_UNBLANK: /* unblank */ seqflags = 0; /* Enable sequencer */ - lcdflags = par->PanelDispCntlReg1 & 0x02; /* LCD normal */ + lcdflags = ((par->PanelDispCntlReg1 | tmpdisp) & 0x02); /* LCD normal */ dpmsflags = 0x00; /* no hsync/vsync suppression */ #ifdef CONFIG_TOSHIBA /* Do we still need this ? */ -- cgit v1.1