diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/ABI/obsolete/proc-pid-oom_adj | 22 | ||||
| -rw-r--r-- | Documentation/leds-class.txt | 21 | ||||
| -rw-r--r-- | Documentation/leds/leds-lp5521.txt | 88 | ||||
| -rw-r--r-- | Documentation/leds/leds-lp5523.txt | 83 | ||||
| -rw-r--r-- | Documentation/sysctl/kernel.txt | 14 |
5 files changed, 219 insertions, 9 deletions
diff --git a/Documentation/ABI/obsolete/proc-pid-oom_adj b/Documentation/ABI/obsolete/proc-pid-oom_adj new file mode 100644 index 0000000..cf63f26 --- /dev/null +++ b/Documentation/ABI/obsolete/proc-pid-oom_adj @@ -0,0 +1,22 @@ +What: /proc/<pid>/oom_adj +When: August 2012 +Why: /proc/<pid>/oom_adj allows userspace to influence the oom killer's + badness heuristic used to determine which task to kill when the kernel + is out of memory. + + The badness heuristic has since been rewritten since the introduction of + this tunable such that its meaning is deprecated. The value was + implemented as a bitshift on a score generated by the badness() + function that did not have any precise units of measure. With the + rewrite, the score is given as a proportion of available memory to the + task allocating pages, so using a bitshift which grows the score + exponentially is, thus, impossible to tune with fine granularity. + + A much more powerful interface, /proc/<pid>/oom_score_adj, was + introduced with the oom killer rewrite that allows users to increase or + decrease the badness() score linearly. This interface will replace + /proc/<pid>/oom_adj. + + A warning will be emitted to the kernel log if an application uses this + deprecated interface. After it is printed once, future warnings will be + suppressed until the kernel is rebooted. diff --git a/Documentation/leds-class.txt b/Documentation/leds-class.txt index 8fd5ca2..58b266b 100644 --- a/Documentation/leds-class.txt +++ b/Documentation/leds-class.txt @@ -60,15 +60,18 @@ Hardware accelerated blink of LEDs Some LEDs can be programmed to blink without any CPU interaction. To support this feature, a LED driver can optionally implement the -blink_set() function (see <linux/leds.h>). If implemented, triggers can -attempt to use it before falling back to software timers. The blink_set() -function should return 0 if the blink setting is supported, or -EINVAL -otherwise, which means that LED blinking will be handled by software. - -The blink_set() function should choose a user friendly blinking -value if it is called with *delay_on==0 && *delay_off==0 parameters. In -this case the driver should give back the chosen value through delay_on -and delay_off parameters to the leds subsystem. +blink_set() function (see <linux/leds.h>). To set an LED to blinking, +however, it is better to use use the API function led_blink_set(), +as it will check and implement software fallback if necessary. + +To turn off blinking again, use the API function led_brightness_set() +as that will not just set the LED brightness but also stop any software +timers that may have been required for blinking. + +The blink_set() function should choose a user friendly blinking value +if it is called with *delay_on==0 && *delay_off==0 parameters. In this +case the driver should give back the chosen value through delay_on and +delay_off parameters to the leds subsystem. Setting the brightness to zero with brightness_set() callback function should completely turn off the LED and cancel the previously programmed diff --git a/Documentation/leds/leds-lp5521.txt b/Documentation/leds/leds-lp5521.txt new file mode 100644 index 0000000..c4d8d15 --- /dev/null +++ b/Documentation/leds/leds-lp5521.txt @@ -0,0 +1,88 @@ +Kernel driver for lp5521 +======================== + +* National Semiconductor LP5521 led driver chip +* Datasheet: http://www.national.com/pf/LP/LP5521.html + +Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo +Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com) + +Description +----------- + +LP5521 can drive up to 3 channels. Leds can be controlled directly via +the led class control interface. Channels have generic names: +lp5521:channelx, where x is 0 .. 2 + +All three channels can be also controlled using the engine micro programs. +More details of the instructions can be found from the public data sheet. + +Control interface for the engines: +x is 1 .. 3 +enginex_mode : disabled, load, run +enginex_load : store program (visible only in engine load mode) + +Example (start to blink the channel 2 led): +cd /sys/class/leds/lp5521:channel2/device +echo "load" > engine3_mode +echo "037f4d0003ff6000" > engine3_load +echo "run" > engine3_mode + +stop the engine: +echo "disabled" > engine3_mode + +sysfs contains a selftest entry. +The test communicates with the chip and checks that +the clock mode is automatically set to the requested one. + +Each channel has its own led current settings. +/sys/class/leds/lp5521:channel0/led_current - RW +/sys/class/leds/lp5521:channel0/max_current - RO +Format: 10x mA i.e 10 means 1.0 mA + +example platform data: + +Note: chan_nr can have values between 0 and 2. + +static struct lp5521_led_config lp5521_led_config[] = { + { + .chan_nr = 0, + .led_current = 50, + .max_current = 130, + }, { + .chan_nr = 1, + .led_current = 0, + .max_current = 130, + }, { + .chan_nr = 2, + .led_current = 0, + .max_current = 130, + } +}; + +static int lp5521_setup(void) +{ + /* setup HW resources */ +} + +static void lp5521_release(void) +{ + /* Release HW resources */ +} + +static void lp5521_enable(bool state) +{ + /* Control of chip enable signal */ +} + +static struct lp5521_platform_data lp5521_platform_data = { + .led_config = lp5521_led_config, + .num_channels = ARRAY_SIZE(lp5521_led_config), + .clock_mode = LP5521_CLOCK_EXT, + .setup_resources = lp5521_setup, + .release_resources = lp5521_release, + .enable = lp5521_enable, +}; + +If the current is set to 0 in the platform data, that channel is +disabled and it is not visible in the sysfs. diff --git a/Documentation/leds/leds-lp5523.txt b/Documentation/leds/leds-lp5523.txt new file mode 100644 index 0000000..fad2feb --- /dev/null +++ b/Documentation/leds/leds-lp5523.txt @@ -0,0 +1,83 @@ +Kernel driver for lp5523 +======================== + +* National Semiconductor LP5523 led driver chip +* Datasheet: http://www.national.com/pf/LP/LP5523.html + +Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo +Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com) + +Description +----------- +LP5523 can drive up to 9 channels. Leds can be controlled directly via +the led class control interface. Channels have generic names: +lp5523:channelx where x is 0...8 + +The chip provides 3 engines. Each engine can control channels without +interaction from the main CPU. Details of the micro engine code can be found +from the public data sheet. Leds can be muxed to different channels. + +Control interface for the engines: +x is 1 .. 3 +enginex_mode : disabled, load, run +enginex_load : microcode load (visible only in load mode) +enginex_leds : led mux control (visible only in load mode) + +cd /sys/class/leds/lp5523:channel2/device +echo "load" > engine3_mode +echo "9d80400004ff05ff437f0000" > engine3_load +echo "111111111" > engine3_leds +echo "run" > engine3_mode + +sysfs contains a selftest entry. It measures each channel +voltage level and checks if it looks reasonable. If the level is too high, +the led is missing; if the level is too low, there is a short circuit. + +Selftest uses always the current from the platform data. + +Each channel contains led current settings. +/sys/class/leds/lp5523:channel2/led_current - RW +/sys/class/leds/lp5523:channel2/max_current - RO +Format: 10x mA i.e 10 means 1.0 mA + +Example platform data: + +Note - chan_nr can have values between 0 and 8. + +static struct lp5523_led_config lp5523_led_config[] = { + { + .chan_nr = 0, + .led_current = 50, + .max_current = 130, + }, +... + }, { + .chan_nr = 8, + .led_current = 50, + .max_current = 130, + } +}; + +static int lp5523_setup(void) +{ + /* Setup HW resources */ +} + +static void lp5523_release(void) +{ + /* Release HW resources */ +} + +static void lp5523_enable(bool state) +{ + /* Control chip enable signal */ +} + +static struct lp5523_platform_data lp5523_platform_data = { + .led_config = lp5523_led_config, + .num_channels = ARRAY_SIZE(lp5523_led_config), + .clock_mode = LP5523_CLOCK_EXT, + .setup_resources = lp5523_setup, + .release_resources = lp5523_release, + .enable = lp5523_enable, +}; diff --git a/Documentation/sysctl/kernel.txt b/Documentation/sysctl/kernel.txt index 3894eaa..209e158 100644 --- a/Documentation/sysctl/kernel.txt +++ b/Documentation/sysctl/kernel.txt @@ -28,6 +28,7 @@ show up in /proc/sys/kernel: - core_uses_pid - ctrl-alt-del - dentry-state +- dmesg_restrict - domainname - hostname - hotplug @@ -213,6 +214,19 @@ to decide what to do with it. ============================================================== +dmesg_restrict: + +This toggle indicates whether unprivileged users are prevented from using +dmesg(8) to view messages from the kernel's log buffer. When +dmesg_restrict is set to (0) there are no restrictions. When +dmesg_restrict is set set to (1), users must have CAP_SYS_ADMIN to use +dmesg(8). + +The kernel config option CONFIG_SECURITY_DMESG_RESTRICT sets the default +value of dmesg_restrict. + +============================================================== + domainname & hostname: These files can be used to set the NIS/YP domainname and the |