diff options
Diffstat (limited to 'include/asm-powerpc/dma.h')
| -rw-r--r-- | include/asm-powerpc/dma.h | 360 |
1 files changed, 0 insertions, 360 deletions
diff --git a/include/asm-powerpc/dma.h b/include/asm-powerpc/dma.h deleted file mode 100644 index a7e06e2..0000000 --- a/include/asm-powerpc/dma.h +++ /dev/null @@ -1,360 +0,0 @@ -#ifndef _ASM_POWERPC_DMA_H -#define _ASM_POWERPC_DMA_H -#ifdef __KERNEL__ - -/* - * Defines for using and allocating dma channels. - * Written by Hennus Bergman, 1992. - * High DMA channel support & info by Hannu Savolainen - * and John Boyd, Nov. 1992. - * Changes for ppc sound by Christoph Nadig - */ - -/* - * Note: Adapted for PowerPC by Gary Thomas - * Modified by Cort Dougan <cort@cs.nmt.edu> - * - * None of this really applies for Power Macintoshes. There is - * basically just enough here to get kernel/dma.c to compile. - * - * There may be some comments or restrictions made here which are - * not valid for the PReP platform. Take what you read - * with a grain of salt. - */ - -#include <asm/io.h> -#include <linux/spinlock.h> -#include <asm/system.h> - -#ifndef MAX_DMA_CHANNELS -#define MAX_DMA_CHANNELS 8 -#endif - -/* The maximum address that we can perform a DMA transfer to on this platform */ -/* Doesn't really apply... */ -#define MAX_DMA_ADDRESS (~0UL) - -#if !defined(CONFIG_PPC_ISERIES) || defined(CONFIG_PCI) - -#ifdef HAVE_REALLY_SLOW_DMA_CONTROLLER -#define dma_outb outb_p -#else -#define dma_outb outb -#endif - -#define dma_inb inb - -/* - * NOTES about DMA transfers: - * - * controller 1: channels 0-3, byte operations, ports 00-1F - * controller 2: channels 4-7, word operations, ports C0-DF - * - * - ALL registers are 8 bits only, regardless of transfer size - * - channel 4 is not used - cascades 1 into 2. - * - channels 0-3 are byte - addresses/counts are for physical bytes - * - channels 5-7 are word - addresses/counts are for physical words - * - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries - * - transfer count loaded to registers is 1 less than actual count - * - controller 2 offsets are all even (2x offsets for controller 1) - * - page registers for 5-7 don't use data bit 0, represent 128K pages - * - page registers for 0-3 use bit 0, represent 64K pages - * - * On PReP, DMA transfers are limited to the lower 16MB of _physical_ memory. - * On CHRP, the W83C553F (and VLSI Tollgate?) support full 32 bit addressing. - * Note that addresses loaded into registers must be _physical_ addresses, - * not logical addresses (which may differ if paging is active). - * - * Address mapping for channels 0-3: - * - * A23 ... A16 A15 ... A8 A7 ... A0 (Physical addresses) - * | ... | | ... | | ... | - * | ... | | ... | | ... | - * | ... | | ... | | ... | - * P7 ... P0 A7 ... A0 A7 ... A0 - * | Page | Addr MSB | Addr LSB | (DMA registers) - * - * Address mapping for channels 5-7: - * - * A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0 (Physical addresses) - * | ... | \ \ ... \ \ \ ... \ \ - * | ... | \ \ ... \ \ \ ... \ (not used) - * | ... | \ \ ... \ \ \ ... \ - * P7 ... P1 (0) A7 A6 ... A0 A7 A6 ... A0 - * | Page | Addr MSB | Addr LSB | (DMA registers) - * - * Again, channels 5-7 transfer _physical_ words (16 bits), so addresses - * and counts _must_ be word-aligned (the lowest address bit is _ignored_ at - * the hardware level, so odd-byte transfers aren't possible). - * - * Transfer count (_not # bytes_) is limited to 64K, represented as actual - * count - 1 : 64K => 0xFFFF, 1 => 0x0000. Thus, count is always 1 or more, - * and up to 128K bytes may be transferred on channels 5-7 in one operation. - * - */ - -/* 8237 DMA controllers */ -#define IO_DMA1_BASE 0x00 /* 8 bit slave DMA, channels 0..3 */ -#define IO_DMA2_BASE 0xC0 /* 16 bit master DMA, ch 4(=slave input)..7 */ - -/* DMA controller registers */ -#define DMA1_CMD_REG 0x08 /* command register (w) */ -#define DMA1_STAT_REG 0x08 /* status register (r) */ -#define DMA1_REQ_REG 0x09 /* request register (w) */ -#define DMA1_MASK_REG 0x0A /* single-channel mask (w) */ -#define DMA1_MODE_REG 0x0B /* mode register (w) */ -#define DMA1_CLEAR_FF_REG 0x0C /* clear pointer flip-flop (w) */ -#define DMA1_TEMP_REG 0x0D /* Temporary Register (r) */ -#define DMA1_RESET_REG 0x0D /* Master Clear (w) */ -#define DMA1_CLR_MASK_REG 0x0E /* Clear Mask */ -#define DMA1_MASK_ALL_REG 0x0F /* all-channels mask (w) */ - -#define DMA2_CMD_REG 0xD0 /* command register (w) */ -#define DMA2_STAT_REG 0xD0 /* status register (r) */ -#define DMA2_REQ_REG 0xD2 /* request register (w) */ -#define DMA2_MASK_REG 0xD4 /* single-channel mask (w) */ -#define DMA2_MODE_REG 0xD6 /* mode register (w) */ -#define DMA2_CLEAR_FF_REG 0xD8 /* clear pointer flip-flop (w) */ -#define DMA2_TEMP_REG 0xDA /* Temporary Register (r) */ -#define DMA2_RESET_REG 0xDA /* Master Clear (w) */ -#define DMA2_CLR_MASK_REG 0xDC /* Clear Mask */ -#define DMA2_MASK_ALL_REG 0xDE /* all-channels mask (w) */ - -#define DMA_ADDR_0 0x00 /* DMA address registers */ -#define DMA_ADDR_1 0x02 -#define DMA_ADDR_2 0x04 -#define DMA_ADDR_3 0x06 -#define DMA_ADDR_4 0xC0 -#define DMA_ADDR_5 0xC4 -#define DMA_ADDR_6 0xC8 -#define DMA_ADDR_7 0xCC - -#define DMA_CNT_0 0x01 /* DMA count registers */ -#define DMA_CNT_1 0x03 -#define DMA_CNT_2 0x05 -#define DMA_CNT_3 0x07 -#define DMA_CNT_4 0xC2 -#define DMA_CNT_5 0xC6 -#define DMA_CNT_6 0xCA -#define DMA_CNT_7 0xCE - -#define DMA_LO_PAGE_0 0x87 /* DMA page registers */ -#define DMA_LO_PAGE_1 0x83 -#define DMA_LO_PAGE_2 0x81 -#define DMA_LO_PAGE_3 0x82 -#define DMA_LO_PAGE_5 0x8B -#define DMA_LO_PAGE_6 0x89 -#define DMA_LO_PAGE_7 0x8A - -#define DMA_HI_PAGE_0 0x487 /* DMA page registers */ -#define DMA_HI_PAGE_1 0x483 -#define DMA_HI_PAGE_2 0x481 -#define DMA_HI_PAGE_3 0x482 -#define DMA_HI_PAGE_5 0x48B -#define DMA_HI_PAGE_6 0x489 -#define DMA_HI_PAGE_7 0x48A - -#define DMA1_EXT_REG 0x40B -#define DMA2_EXT_REG 0x4D6 - -#ifndef __powerpc64__ - /* in arch/ppc/kernel/setup.c -- Cort */ - extern unsigned int DMA_MODE_WRITE; - extern unsigned int DMA_MODE_READ; - extern unsigned long ISA_DMA_THRESHOLD; -#else - #define DMA_MODE_READ 0x44 /* I/O to memory, no autoinit, increment, single mode */ - #define DMA_MODE_WRITE 0x48 /* memory to I/O, no autoinit, increment, single mode */ -#endif - -#define DMA_MODE_CASCADE 0xC0 /* pass thru DREQ->HRQ, DACK<-HLDA only */ - -#define DMA_AUTOINIT 0x10 - -extern spinlock_t dma_spin_lock; - -static __inline__ unsigned long claim_dma_lock(void) -{ - unsigned long flags; - spin_lock_irqsave(&dma_spin_lock, flags); - return flags; -} - -static __inline__ void release_dma_lock(unsigned long flags) -{ - spin_unlock_irqrestore(&dma_spin_lock, flags); -} - -/* enable/disable a specific DMA channel */ -static __inline__ void enable_dma(unsigned int dmanr) -{ - unsigned char ucDmaCmd = 0x00; - - if (dmanr != 4) { - dma_outb(0, DMA2_MASK_REG); /* This may not be enabled */ - dma_outb(ucDmaCmd, DMA2_CMD_REG); /* Enable group */ - } - if (dmanr <= 3) { - dma_outb(dmanr, DMA1_MASK_REG); - dma_outb(ucDmaCmd, DMA1_CMD_REG); /* Enable group */ - } else { - dma_outb(dmanr & 3, DMA2_MASK_REG); - } -} - -static __inline__ void disable_dma(unsigned int dmanr) -{ - if (dmanr <= 3) - dma_outb(dmanr | 4, DMA1_MASK_REG); - else - dma_outb((dmanr & 3) | 4, DMA2_MASK_REG); -} - -/* Clear the 'DMA Pointer Flip Flop'. - * Write 0 for LSB/MSB, 1 for MSB/LSB access. - * Use this once to initialize the FF to a known state. - * After that, keep track of it. :-) - * --- In order to do that, the DMA routines below should --- - * --- only be used while interrupts are disabled! --- - */ -static __inline__ void clear_dma_ff(unsigned int dmanr) -{ - if (dmanr <= 3) - dma_outb(0, DMA1_CLEAR_FF_REG); - else - dma_outb(0, DMA2_CLEAR_FF_REG); -} - -/* set mode (above) for a specific DMA channel */ -static __inline__ void set_dma_mode(unsigned int dmanr, char mode) -{ - if (dmanr <= 3) - dma_outb(mode | dmanr, DMA1_MODE_REG); - else - dma_outb(mode | (dmanr & 3), DMA2_MODE_REG); -} - -/* Set only the page register bits of the transfer address. - * This is used for successive transfers when we know the contents of - * the lower 16 bits of the DMA current address register, but a 64k boundary - * may have been crossed. - */ -static __inline__ void set_dma_page(unsigned int dmanr, int pagenr) -{ - switch (dmanr) { - case 0: - dma_outb(pagenr, DMA_LO_PAGE_0); - dma_outb(pagenr >> 8, DMA_HI_PAGE_0); - break; - case 1: - dma_outb(pagenr, DMA_LO_PAGE_1); - dma_outb(pagenr >> 8, DMA_HI_PAGE_1); - break; - case 2: - dma_outb(pagenr, DMA_LO_PAGE_2); - dma_outb(pagenr >> 8, DMA_HI_PAGE_2); - break; - case 3: - dma_outb(pagenr, DMA_LO_PAGE_3); - dma_outb(pagenr >> 8, DMA_HI_PAGE_3); - break; - case 5: - dma_outb(pagenr & 0xfe, DMA_LO_PAGE_5); - dma_outb(pagenr >> 8, DMA_HI_PAGE_5); - break; - case 6: - dma_outb(pagenr & 0xfe, DMA_LO_PAGE_6); - dma_outb(pagenr >> 8, DMA_HI_PAGE_6); - break; - case 7: - dma_outb(pagenr & 0xfe, DMA_LO_PAGE_7); - dma_outb(pagenr >> 8, DMA_HI_PAGE_7); - break; - } -} - -/* Set transfer address & page bits for specific DMA channel. - * Assumes dma flipflop is clear. - */ -static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int phys) -{ - if (dmanr <= 3) { - dma_outb(phys & 0xff, - ((dmanr & 3) << 1) + IO_DMA1_BASE); - dma_outb((phys >> 8) & 0xff, - ((dmanr & 3) << 1) + IO_DMA1_BASE); - } else { - dma_outb((phys >> 1) & 0xff, - ((dmanr & 3) << 2) + IO_DMA2_BASE); - dma_outb((phys >> 9) & 0xff, - ((dmanr & 3) << 2) + IO_DMA2_BASE); - } - set_dma_page(dmanr, phys >> 16); -} - - -/* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for - * a specific DMA channel. - * You must ensure the parameters are valid. - * NOTE: from a manual: "the number of transfers is one more - * than the initial word count"! This is taken into account. - * Assumes dma flip-flop is clear. - * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7. - */ -static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count) -{ - count--; - if (dmanr <= 3) { - dma_outb(count & 0xff, - ((dmanr & 3) << 1) + 1 + IO_DMA1_BASE); - dma_outb((count >> 8) & 0xff, - ((dmanr & 3) << 1) + 1 + IO_DMA1_BASE); - } else { - dma_outb((count >> 1) & 0xff, - ((dmanr & 3) << 2) + 2 + IO_DMA2_BASE); - dma_outb((count >> 9) & 0xff, - ((dmanr & 3) << 2) + 2 + IO_DMA2_BASE); - } -} - - -/* Get DMA residue count. After a DMA transfer, this - * should return zero. Reading this while a DMA transfer is - * still in progress will return unpredictable results. - * If called before the channel has been used, it may return 1. - * Otherwise, it returns the number of _bytes_ left to transfer. - * - * Assumes DMA flip-flop is clear. - */ -static __inline__ int get_dma_residue(unsigned int dmanr) -{ - unsigned int io_port = (dmanr <= 3) - ? ((dmanr & 3) << 1) + 1 + IO_DMA1_BASE - : ((dmanr & 3) << 2) + 2 + IO_DMA2_BASE; - - /* using short to get 16-bit wrap around */ - unsigned short count; - - count = 1 + dma_inb(io_port); - count += dma_inb(io_port) << 8; - - return (dmanr <= 3) ? count : (count << 1); -} - -/* These are in kernel/dma.c: */ - -/* reserve a DMA channel */ -extern int request_dma(unsigned int dmanr, const char *device_id); -/* release it again */ -extern void free_dma(unsigned int dmanr); - -#ifdef CONFIG_PCI -extern int isa_dma_bridge_buggy; -#else -#define isa_dma_bridge_buggy (0) -#endif - -#endif /* !defined(CONFIG_PPC_ISERIES) || defined(CONFIG_PCI) */ - -#endif /* __KERNEL__ */ -#endif /* _ASM_POWERPC_DMA_H */ |