aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/mmc
Commit message (Collapse)AuthorAgeFilesLines
...
| * mmc: sd: set current limit for uhs cardsArindam Nath2011-05-242-0/+73
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We decide on the current limit to be set for the card based on the Capability of Host Controller to provide current at 1.8V signalling, and the maximum current limit of the card as indicated by CMD6 mode 0. We then set the current limit for the card using CMD6 mode 1. As per the Physical Layer Spec v3.01, the current limit switch is only applicable for SDR50, SDR104, and DDR50 bus speed modes. For other UHS-I modes, we set the default current limit of 200mA. Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by: Arindam Nath <arindam.nath@amd.com> Reviewed-by: Philip Rakity <prakity@marvell.com> Tested-by: Philip Rakity <prakity@marvell.com> Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: sd: add support for uhs bus speed mode selectionArindam Nath2011-05-243-3/+108
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for setting UHS-I bus speed mode during UHS-I initialization procedure. Since both the host and card can support more than one bus speed, we select the highest speed based on both of their capabilities. First we set the bus speed mode for the card using CMD6 mode 1, and then we program the host controller to support the required speed mode. We also set High Speed Enable in case one of the UHS-I modes is selected. We take care to reset SD clock before setting UHS mode in the Host Control2 register, and then re-enable it as per the Host Controller spec v3.00. We then set the clock frequency for the UHS-I mode selected. Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by: Arindam Nath <arindam.nath@amd.com> Reviewed-by: Philip Rakity <prakity@marvell.com> Tested-by: Philip Rakity <prakity@marvell.com> Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: sdhci: reset sdclk before setting high speed enableArindam Nath2011-05-241-3/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As per Host Controller spec v3.00, we reset SDCLK before setting High Speed Enable, and then set it back to avoid generating clock gliches. Before enabling SDCLK again, we make sure the clock is stable, so we use sdhci_set_clock(). Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by: Arindam Nath <arindam.nath@amd.com> Reviewed-by: Philip Rakity <prakity@marvell.com> Tested-by: Philip Rakity <prakity@marvell.com> Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: sd: add support for driver type selectionArindam Nath2011-05-247-30/+176
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for setting driver strength during UHS-I initialization procedure. Since UHS-I cards set S18A (bit 24) in response to ACMD41, we use this as a base for UHS-I initialization. We modify the parameter list of mmc_sd_get_cid() so that we can save the ROCR from ACMD41 to check whether bit 24 is set. We decide whether the Host Controller supports A, C, or D driver type depending on the Capabilities register. Driver type B is suported by default. We then set the appropriate driver type for the card using CMD6 mode 1. As per Host Controller spec v3.00, we set driver type for the host only if Preset Value Enable in the Host Control2 register is not set. SDHCI_HOST_CONTROL has been renamed to SDHCI_HOST_CONTROL1 to conform to the spec. Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by: Arindam Nath <arindam.nath@amd.com> Reviewed-by: Philip Rakity <prakity@marvell.com> Tested-by: Philip Rakity <prakity@marvell.com> Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: sd: query function modes for uhs cardsArindam Nath2011-05-241-10/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SD cards which conform to Physical Layer Spec v3.01 can support additional Bus Speed Modes, Driver Strength, and Current Limit other than the default values. We use CMD6 mode 0 to read these additional card functions. The values read here will be used during UHS-I initialization steps. Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by: Arindam Nath <arindam.nath@amd.com> Reviewed-by: Philip Rakity <prakity@marvell.com> Tested-by: Philip Rakity <prakity@marvell.com> Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: sd: add support for signal voltage switch procedureArindam Nath2011-05-245-17/+262
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Host Controller v3.00 adds another Capabilities register. Apart from other things, this new register indicates whether the Host Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec doesn't mention about explicit support for SDR12 and SDR25 UHS-I modes, so the Host Controller v3.00 should support them by default. Also if the controller supports SDR104 mode, it will also support SDR50 mode as well. So depending on the host support, we set the corresponding MMC_CAP_* flags. One more new register. Host Control2 is added in v3.00, which is used during Signal Voltage Switch procedure described below. Since as per v3.00 spec, UHS-I supported hosts should set S18R to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also need to set XPC (bit 28) of OCR in case the host can supply >150mA. This support is indicated by the Maximum Current Capabilities register of the Host Controller. If the response of ACMD41 has both CCS and S18A set, we start the signal voltage switch procedure, which if successfull, will switch the card from 3.3V signalling to 1.8V signalling. Signal voltage switch procedure adds support for a new command CMD11 in the Physical Layer Spec v3.01. As part of this procedure, we need to set 1.8V Signalling Enable (bit 3) of Host Control2 register, which if remains set after 5ms, means the switch to 1.8V signalling is successfull. Otherwise, we clear bit 24 of OCR and retry the initialization sequence. When we remove the card, and insert the same or another card, we need to make sure that we start with 3.3V signalling voltage. So we call mmc_set_signal_voltage() with MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling voltage before we actually start initializing the card. Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by: Arindam Nath <arindam.nath@amd.com> Reviewed-by: Philip Rakity <prakity@marvell.com> Tested-by: Philip Rakity <prakity@marvell.com> Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: core: Add mmc CMD+ACMD passthrough ioctlJohn Calixto2011-05-242-1/+203
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Allows appropriately-privileged applications to send CMD (normal) and ACMD (application-specific; preceded with CMD55) commands to cards/devices on the mmc bus. This is primarily useful for enabling the security functionality built in to every SD card. It can also be used as a generic passthrough (e.g. to enable virtual machines to control mmc bus devices directly). However, this use case has not been tested rigorously. Generic passthrough testing was only conducted for a few non-security opcodes to prove the feasibility of the passthrough. Since any opcode can be sent using this passthrough, it is very possible to render the card/device unusable. Applications that use this ioctl must have CAP_SYS_RAWIO. Security commands tested on TI PCIxx12 (SDHCI), Sigma Designs SMP8652 SoC, TI OMAP3621/OMAP3630 SoC, Samsung S5PC110 SoC, Qualcomm MSM7200A SoC. Signed-off-by: John Calixto <john.calixto@modsystems.com> Reviewed-by: Andrei Warkentin <andreiw@motorola.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: block: init force_ro sysfs attributeRabin Vincent2011-05-241-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To avoid lockdep warnings: BUG: key dc90a520 not in .data! ------------[ cut here ]------------ WARNING: at /home/rabin/kernel/arm/kernel/lockdep.c:2701 sysfs_add_file_mode+0x4c/0xb0() Modules linked in: [<c004b5d8>] (unwind_backtrace+0x0/0xe4) from [<c0074f20>] (warn_slowpath_common+0x4c/0x64) [<c0074f20>] (warn_slowpath_common+0x4c/0x64) from [<c0074f50>] (warn_slowpath_null+0x18/0x1c) [<c0074f50>] (warn_slowpath_null+0x18/0x1c) from [<c0157fec>] (sysfs_add_file_mode+0x4c/0xb0) [<c0157fec>] (sysfs_add_file_mode+0x4c/0xb0) from [<c02d61e4>] (mmc_add_disk+0x40/0x64) [<c02d61e4>] (mmc_add_disk+0x40/0x64) from [<c02d64cc>] (mmc_blk_probe+0x188/0x1fc) [<c02d64cc>] (mmc_blk_probe+0x188/0x1fc) from [<c02ce820>] (mmc_bus_probe+0x14/0x18) ... Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: sdhci: Fix read-only detection with JMicron 388 chipTakashi Iwai2011-05-242-4/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On HP laptops with JMicron 388 chip, the write-locked SD card isn't detected correctly as read-only in many cases. This is because the PRESENT_STATE register becomes unsable just after plugging, and it returns the WRITE_PROTECT bit wrongly at the first read. This patch fixes the read-only detection by adding a new sdhci quirk indicating to check the register more intensively with a relatively long delay. The patch is tested with 2.6.39-rc4 kernel. Cc: Aries Lee <arieslee@jmicron.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: Ensure hardware partitions don't mess with mmcblk device naming.Andrei Warkentin2011-05-241-7/+19
| | | | | | | | | | | | | | | | | | With the hardware partitions support (which represent additional logical devices present on MMC), devidx does not correspond with index used to form /dev/mmcblkX names. So use an additional allocated index for device names. Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: sdhci: Add pre and post reset processing for chip specific resetPhilip Rakity2011-05-242-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Marvell pxa controllers have private registers that may need to be modified before and after a reset is done. For example, the SD reset operation, RESET_ALL, will reset the private registers to their default state. This will cause the clock adjustment registers that may have been programmed to have incorrect values. RESET_DATA sometimes needs to be delayed before the reset is done (depending on SoC) to enable any transactions being handled by the SDIO card to be completed. Needed in pre SD 3.0 silicon to handle clock gating. Implement hooks to allow this to happen. Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: sdhci: Fix SDHCI_QUIRK_TIMEOUT_USES_SDCLKMark Brown2011-05-241-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 373e6a (mmc: sdhci: R1B command handling + MMC_CAP_ERASE) moved the handling of SDHCI_QUIRK_TIMEOUT_USES_SDCLK from sdhci_calc_timeout() to sdhci_add_host(). This causes division by zero errors on at least the S3C SDHCI controller as the quirk implementation needs host->clock set to work but host->clock has not been set when sdhci_add_host() is called. Fix this by backing out that portion of the change, the clock may vary at runtime anyway. It does occur to me that we may want to move the quirk to where we set the clock but this seems more invasive and I'm concerned about undesirable side effects. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Andrei Warkentin <andreiw@motorola.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: initialize struct mmc_request at declaration timeChris Ball2011-05-246-34/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Converts from: struct mmc_request mrq; memset(&mrq, 0, sizeof(struct mmc_request)); to: struct mmc_request mrq = {0}; because it's shorter, as performant, and easier to work out whether initialization has happened. Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: initialize struct mmc_data at declaration timeChris Ball2011-05-245-21/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Converts from: struct mmc_data data; memset(&data, 0, sizeof(struct mmc_data)); to: struct mmc_data data = {0}; because it's shorter, as performant, and easier to work out whether initialization has happened. Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: initialize struct mmc_command at declaration timeChris Ball2011-05-246-92/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Converts from: struct mmc_command cmd; memset(&cmd, 0, sizeof(struct mmc_command)); to: struct mmc_command cmd = {0}; because it's shorter, as performant, and easier to work out whether initialization has happened. Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: card: Fix use of uninitialized data in mmc_blk_issue_rw_rq.Chris Ball2011-05-241-0/+1
| | | | | | | | | | | | mmc_blk_issue_rw_rq did not zero out mmc_command on stack. Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: core: Fix use of uninitialized data in mmc_send_if_cond.Chris Ball2011-05-241-0/+2
| | | | | | | | | | | | mmc_send_if_cond did not zero out mmc_command on stack. Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: core: Fix use of uninitialized data in mmc_cmd_app.Andrei Warkentin2011-05-241-0/+2
| | | | | | | | | | | | | | | | mmc_cmd_app did not zero out mmc_command on stack. Reported-by: Chuanxiao Dong <chuanxiao.dong@intel.com> Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: quirks: Fix erase/trim for certain SanDisk cards.Andrei Warkentin2011-05-241-1/+42
| | | | | | | | | | | | | | CMD38 argument is passed through EXT_CSD[113]. Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: sdhci: work around broken dma boundary behaviorMikko Vinni2011-05-242-5/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some SD host controllers (noticed on an integrated JMicron SD reader on an HP Pavilion dv5-1250eo laptop) don't update the dma address register before signaling a dma interrupt due to a dma boundary. Update the register manually to the next boundary (by default 512KiB), at which the transfer stopped. As long as each transfer is at most 512KiB in size (guaranteed by a BUG_ON in sdhci_prepare_data()) and the boundary is kept at the default value, this fix is needed at most once per transfer. Smaller boundaries are taken care of by counting the transferred bytes. Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=28462 Signed-off-by: Mikko Vinni <mmvinni@yahoo.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: quirks: Support for block quirks.Andrei Warkentin2011-05-241-0/+7
| | | | | | | | | | | | | | Block quirks implemented using core/quirks.c support. Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: MMC boot partitions support.Andrei Warkentin2011-05-242-40/+256
| | | | | | | | | | | | | | | | | | Allows device MMC boot partitions to be accessed. MMC partitions are treated effectively as separate block devices on the same MMC card. Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: card: block.c cleanup for host claim/release.Andrei Warkentin2011-05-241-18/+13
| | | | | | | | | | | | | | | | | | | | Move host claim/release into mmc_blk_issue_rq. (This is helpful so that selecting partition only has to happen in one place for these commands.) Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: core: Allow setting CMD timeout for CMD6 (SWITCH).Andrei Warkentin2011-05-243-8/+23
| | | | | | | | | | | | | | | | | | CMD6 is an R1B-type command, where DAT is used as busy. Depending on register written using CMD6, timeout value can be different as per spec. Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: sdhci: R1B command handling + MMC_CAP_ERASE.Andrei Warkentin2011-05-241-16/+26
| | | | | | | | | | | | | | | | | | | | | | ERASE command needs R1B response, so fix R1B-type command handling for SDHCI controller. For non-DAT commands using a busy response, the cmd->cmd_timeout_ms (in ms) field is used for timeout calculations. Based on patch by Chuanxiao Dong <chuanxiao.dong@intel.com> Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: core: Rename erase_timeout to cmd_timeout_ms.Andrei Warkentin2011-05-241-18/+21
| | | | | | | | | | | | | | | | | | Renames erase_timeout to cmd_timeout_ms inside struct mmc_command. First step to making host honor timeouts for non-data-transfer commands. Cleans up erase timeout code. Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: quirks: Extends card quirks with MMC/SD quirks matching the CID.Andrei Warkentin2011-05-243-54/+43
| | | | | | | | | | | | | | | | | | | | The current mechanism is SDIO-only. This allows us to create function-specific quirks, without creating messy Kconfig dependencies, or polluting core/ with function-specific code. Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: core: fix memory leak in mmc_add_hostWolfram Sang2011-05-241-2/+2
| | | | | | | | | | | | | | | | | | led_trigger_register_simple() allocates memory which must not be leaked in the error-path of mmc_add_host. Move it past the only error-check in the function. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: sdhci-pci: Fix checkpatch.pl errorsAmeya Palande2011-05-241-23/+21
| | | | | | | | | | | | | | | | This patch fixes 21 errors and 6 warnings reported by checkpatch.pl. Signed-off-by: Ameya Palande <2ameya@gmail.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: quirks: wl1271 is MMC_QUIRK_DISABLE_CDOhad Ben-Cohen2011-05-241-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The wl12xx device supports disconnecting the pull-up resistor on CD/DAT[3] (pin 1) of the card. Tell SDIO core to disconnect that resistor during card init, since we don't need it at that point (and anyway all hosts shall provide pull-up resistors on all data lines DAT[3:0] as described in section 6 of the SD physical specification). As a result, this may save some power, but it's also generally healthy since it prevents both ends from pulling up that pin, which results in undesirable asymmetric physical bus. Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: add MMC_QUIRK_DISABLE_CDOhad Ben-Cohen2011-05-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | 006ebd5d introduced sdio_disable_cd(), which disconnects the pull-up resistor on CD/DAT[3] (pin 1) of the card. Make it possible to start using sdio_disable_cd() by introducing MMC_QUIRK_DISABLE_CD. Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: quirks: wl1271 is MMC_QUIRK_NONSTD_FUNC_IFOhad Ben-Cohen2011-05-241-0/+2
| | | | | | | | | | | | | | | | | | | | Tell SDIO core to ignore the standard SDIO function interface codes indicated by the wl1271. This is required because the wl1271 erroneously indicates its first function as a standard Bluetooth SDIO interface, and that drives btsdio mad. Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: add MMC_QUIRK_NONSTD_FUNC_IFOhad Ben-Cohen2011-05-241-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | Introduce MMC_QUIRK_NONSTD_FUNC_IF to ignore the "SDIO Standard Function interface code" as indicated by the card's FBR, and instead treat all functions as non-standard interfaces. This is required to prevent standard drivers from facing errors when trying to communicate with SDIO cards that erroneously indicate standard function interface codes. Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: do not switch to 1-bit mode if not requiredOhad Ben-Cohen2011-05-241-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 6b5eda36 followed SDIO spec part E1 section 8, which states that in case SDIO interrupts are being used to wake up a suspended host, then it is required to switch to 1-bit mode before stopping the clock. Before switching to 1-bit mode (or back to 4-bit mode on resume), make sure that SDIO interrupts are really being used to wake the host. This is helpful for devices which have an external irq line (e.g. wl1271), and do not use SDIO interrupts to wake up the host. In this case, switching to 1-bit mode (and back to 4-bit mode on resume) is not necessary. Reported-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: mmc_card_keep_power cleanupsOhad Ben-Cohen2011-05-242-7/+7
| | | | | | | | | | | | | | | | | | | | | | mmc_card_is_powered_resumed is a mouthful; instead, simply use mmc_card_keep_power, which also better explains the purpose of the macro. Employ mmc_card_keep_power() where possible. Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: Reliable write support.Andrei Warkentin2011-05-242-4/+82
| | | | | | | | | | | | | | | | | | | | Allows reliable writes to be used for MMC writes. Reliable writes are used to service write REQ_FUA/REQ_META requests. Handles both the legacy and the enhanced reliable write support in MMC cards. Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: sdhci: change CONFIG of MMC_SDHCI_TEGRA from 'tristate' to 'bool'Shawn Guo2011-05-241-1/+1
| | | | | | | | | | | | | | | | | | | | This config option is used to decide whether tegra sdhci support should be build into the sdhci-platform module. So setting it 'm' is nonsense, since we can't build part of an module as a module. The effect for 'm' will probably be the same as for 'n'. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: tegra: add pm_flagsVenkat Rao2011-05-241-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable fast bcm4329 WIFI suspend/resume on Tegra2 board. This patch allows the mach-tegra support to tell the tegra MMC host controller to NOT turn off power for the MMC controller the WIFI part lives behind. Thus bcm4329 firmware doesn't need to be reloaded. Signed-off-by: Venkat Rao <vrao@broadcom.com> Tested-by: Grant Grundler <grundler@chromium.org> Reviewed-by: Olof Johansson <olof@lixom.net> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: remove redundant irq disablingJohn Ogness2011-05-241-8/+0
| | | | | | | | | | | | | | | | | | | | There is no need to disable irq's when using the sg_copy_*_buffer() functions because those functions do that already. There are also no races for the mm_queue struct here that would require the irq's to be disabled before calling sg_copy_*_buffer(). Signed-off-by: John Ogness <john.ogness@linutronix.de> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: Ensure linux starts in eMMC user partitionPhilip Rakity2011-05-241-0/+10
| | | | | | | | | | | | | | | | | | | | uBoot sometimes leaves eMMC pointing to the private boot partition. Ensure we always start looking at the user partition. Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Bruce Clemens <bpclemens@marvell.com> Signed-off-by: Mark F. Brown <markb@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6Linus Torvalds2011-05-241-1/+1
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: pcmcia: Make struct pcmcia_device_id const, sound drivers edition staging: pcmcia: Convert pcmcia_device_id declarations to const pcmcia: Convert pcmcia_device_id declarations to const pcmcia: Make declaration and uses of struct pcmcia_device_id const pcmcia/sa1100: put sa11x0_pcmcia_hw_init[] to .devinit.data
| * | pcmcia: Convert pcmcia_device_id declarations to constJoe Perches2011-05-061-1/+1
| |/ | | | | | | | | | | | | | | | | | | | | | | | | Saves about 50KB of data. Old/new size of all objects: text data bss dec hex filename 563015 80096 130684 773795 bcea3 (TOTALS) 610916 32256 130632 773804 bceac (TOTALS) Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be> (for drivers/net/can/softing/softing_cs.c) Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* | Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds2011-05-232-16/+31
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (137 commits) ARM: bcmring: convert to use sp804 clockevents ARM: bcmring: convert to sp804 clocksource ARM: 6912/1: bcmring: Add clkdev table in init_early clockevents: ARM sp804: obtain sp804 timer rate via clks clockevents: ARM sp804: allow clockevent name to be specified clocksource: ARM sp804: obtain sp804 timer rate via clks clocksource: ARM sp804: allow clocksource name to be specified clocksource: convert OMAP1 to 32-bit down counting clocksource clocksource: convert MXS timrotv2 to 32-bit down counting clocksource clocksource: convert SPEAr platforms 16-bit up counting clocksource clocksource: convert Integrator/AP 16-bit down counting clocksource clocksource: convert W90x900 24-bit down counting clocksource clocksource: convert ARM 32-bit down counting clocksources clocksource: convert ARM 32-bit up counting clocksources clocksource: add common mmio clocksource ARM: update sa1100 to reflect PXA updates ARM: omap1: convert to using readl/writel instead of volatile struct ARM: omap1: delete useless interrupt handler ARM: s5p: consolidate selection of timer register ARM: 6939/1: fix missing 'cpu_relax()' declaration ...
| | \
| | \
| | \
| | \
| | \
| | \
| *-----. \ Merge branches 'consolidate', 'ep93xx', 'fixes', 'misc', 'mmci', 'remove' ↵Russell King2011-05-232-16/+31
| |\ \ \ \ \ | | | |_|_|/ | | |/| | | | | | | | | and 'spear' into for-linus
| | | * | | ARM: 6858/1: mmci: force negative edge on clock bypass for ux500Linus Walleij2011-05-121-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes a regression on high clock speeds with the MMCI on ux500. We need to make sure we derive the passthru clock on the falling edge of the incoming clock if it shall work at high frequencies, and on the ux500's there is a special bit for this. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | | * | | ARM: 6785/1: mmci: separate out ST Micro register definesLinus Walleij2011-05-112-16/+29
| | |/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The mmci.h header contained a few registers not clearly marked as ST Micro only, rectify this and remove the HWFC magic in the process. The idea is to make the mmci.h header file more ordered so other vendors with PL180 derivates can see where to put in their custom register defines. Includes portions of an earlier patch from Sebastian Rasmussen. Acked-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* | | | | Merge branch 'for-linus' of ↵Linus Torvalds2011-05-231-1/+1
|\ \ \ \ \ | |/ / / / |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits) b43: fix comment typo reqest -> request Haavard Skinnemoen has left Atmel cris: typo in mach-fs Makefile Kconfig: fix copy/paste-ism for dell-wmi-aio driver doc: timers-howto: fix a typo ("unsgined") perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course'). treewide: fix a few typos in comments regulator: change debug statement be consistent with the style of the rest Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations" audit: acquire creds selectively to reduce atomic op overhead rtlwifi: don't touch with treewide double semicolon removal treewide: cleanup continuations and remove logging message whitespace ath9k_hw: don't touch with treewide double semicolon removal include/linux/leds-regulator.h: fix syntax in example code tty: fix typo in descripton of tty_termios_encode_baud_rate xtensa: remove obsolete BKL kernel option from defconfig m68k: fix comment typo 'occcured' arch:Kconfig.locks Remove unused config option. treewide: remove extra semicolons ...
| * | | | Haavard Skinnemoen has left AtmelJean Delvare2011-05-181-1/+1
| | |/ / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | Haavard's e-mail address at Atmel is no longer valid. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* | | | drivercore: revert addition of of_match to struct deviceGrant Likely2011-05-181-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit b826291c, "drivercore/dt: add a match table pointer to struct device" added an of_match pointer to struct device to cache the of_match_table entry discovered at driver match time. This was unsafe because matching is not an atomic operation with probing a driver. If two or more drivers are attempted to be matched to a driver at the same time, then the cached matching entry pointer could get overwritten. This patch reverts the of_match cache pointer and reworks all users to call of_match_device() directly instead. Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* | | | Revert "mmc: fix a race between card-detect rescan and clock-gate work ↵Chris Ball2011-05-161-4/+5
| |/ / |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | instances" This reverts commit 26fc8775b51484d8c0a671198639c6d5ae60533e, which has been reported to cause boot/resume-time crashes for some users: https://bbs.archlinux.org/viewtopic.php?id=118751. Signed-off-by: Chris Ball <cjb@laptop.org> Cc: <stable@kernel.org>
generated by cgit v1.1 at 2025-08-17 10:11:44 +0000