aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/can/Kconfig
Commit message (Collapse)AuthorAgeFilesLines
* can: c_can: Added support for Bosch C_CAN controllerBhupesh Sharma2011-02-131-0/+2
| | | | | | | | | | | | | | | | | | | | Bosch C_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch C_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ipmodules_1/c_can/users_manual_c_can.pdf This patch adds the support for this controller. The following are the design choices made while writing the controller driver: 1. Interface Register set IF1 has be used only in the current design. 2. Out of the 32 Message objects available, 16 are kept aside for RX purposes and the rest for TX purposes. 3. NAPI implementation is such that both the TX and RX paths function in polling mode. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* slcan: fix referenced website in Kconfig help textOliver Hartkopp2011-01-301-1/+1
| | | | | | | | Fix the referenced project website to www.mictronics.de in the Kconfig help text for the slcan driver. Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: add driver for Softing cardKurt Van Dijck2011-01-211-0/+2
| | | | | | | | | | This patch adds a driver for the platform:softing device. This will create (up to) 2 CAN network devices from 1 platform:softing device Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: add slcan driver for serial/USB-serial CAN adaptersOliver Hartkopp2010-12-081-0/+21
| | | | | | | | | | | | | | This patch adds support for serial/USB-serial CAN adapters implementing the LAWICEL ASCII protocol for CAN frame transport over serial lines. The driver implements the SLCAN line discipline and is heavily based on the slip.c driver. Therefore the code style remains similar to slip.c to be able to apply changes of the SLIP driver to the SLCAN driver easily. For more details see the slcan Kconfig entry. Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* pch_can: depends on PCIRandy Dunlap2010-10-251-1/+1
| | | | | | | | | | | Fix pch_can build when CONFIG_PCI is not enabled. It uses pci interfaces and data structures, so it should depend on PCI. drivers/net/can/pch_can.c:1044: error: implicit declaration of function 'pci_enable_msi' drivers/net/can/pch_can.c:1079: error: implicit declaration of function 'pci_disable_msi' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: Topcliff: Add PCH_CAN driver.Masayuki Ohtake2010-10-241-0/+8
| | | | | | | | | | | | CAN driver of Topcliff PCH Topcliff PCH is the platform controller hub that is going to be used in Intel's upcoming general embedded platform. All IO peripherals in Topcliff PCH are actually devices sitting on AMBA bus. Topcliff PCH has CAN I/F. This driver enables CAN function. Signed-off-by: Masayuki Ohtake <masa-korg@dsn.okisemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* CAN: Add Flexcan CAN controller driverMarc Kleine-Budde2010-07-221-0/+9
| | | | | | | | | | | | This core is found on some Freescale SoCs and also some Coldfire SoCs. Support for Coldfire is missing though at the moment as they have an older revision of the core which does not have RX FIFO support. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* can: Add support for Janz VMOD-ICAN3 Intelligent CAN moduleIra W. Snyder2010-05-281-0/+10
| | | | | | | | | | | The Janz VMOD-ICAN3 is a MODULbus daughterboard which fits onto any MODULbus carrier board. It is an intelligent CAN controller with a microcontroller and associated firmware. Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* can: CAN_MCP251X should depend on HAS_DMAGeert Uytterhoeven2009-12-131-1/+1
| | | | | | | | | | | When building for Sun 3: drivers/net/can/mcp251x.c:1074: undefined reference to `dma_free_coherent' drivers/net/can/mcp251x.c:976: undefined reference to `dma_alloc_coherent' drivers/net/can/mcp251x.c:1050: undefined reference to `dma_free_coherent' Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: add the driver for Analog Devices Blackfin on-chip CAN controllersBarry Song2009-12-111-0/+9
| | | | | | | Signed-off-by: Barry Song <21cnbao@gmail.com> Signed-off-by: H.J. Oertel <oe@port.de> Signed-off-by: Wolfgang Grandegger <wg@grandegger.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/can/mscan: improve buildWolfram Sang2009-11-171-18/+1
| | | | | | | | - move Kconfig entries to the subdirectory - do remaining renames of mpc52xx to mpc5xxx Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2009-11-171-55/+5
|\ | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/can/Kconfig
| * can: Fix driver Kconfig structureOliver Hartkopp2009-11-131-55/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In 2.6.32-rc the new EMS USB CAN driver was contributed and added the Kconfig entry right behind an entry of the same *vendor*. This teared the SJA1000 based driver selection into pieces. This fix cleans up the 2.6.32-rc Kconfig files for the CAN drivers and moves the SJA1000 and USB Kconfig portions into the belonging directories. As there are many new CAN drivers in the queue getting this cleanup into 2.6.32-rc would massively reduce the problems for the upcoming drivers. Thanks, Oliver Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/can: add driver for mscan family & mpc52xx_mscanWolfram Sang2009-11-131-0/+19
| | | | | | | | | | | | | | | | | | | | | | Taken from socketcan-svn, fixed remaining todos, cleaned up, tested with a phyCORE-MPC5200B-IO and a custom board. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: David Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* | can: Driver for the Microchip MCP251x SPI CAN controllersChristian Pellegrin2009-11-081-0/+6
| | | | | | | | | | | | Signed-off-by: Christian Pellegrin <chripell@fsfe.org> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | can: add TI CAN (HECC) driverAnant Gole2009-10-071-0/+7
|/ | | | | | | | | | TI HECC (High End CAN Controller) module is found on many TI devices. It has 32 hardware mailboxes with full implementation of CAN protocol 2.0B with bus speeds up to 1Mbps. Specifications of the module are available on TI web <http://www.ti.com> Signed-off-by: Anant Gole <anantgole@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* at91_can: add driver for Atmel's CAN controller on AT91SAM9263Marc Kleine-Budde2009-09-221-0/+6
| | | | | | | | | This patch add the driver for the SoC CAN controller in Atmel's AT91SAM9263. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interfaceSebastian Haas2009-09-211-0/+7
| | | | | | | | | This patch adds support for one channel CAN/USB interace CPC-USB/ARM7 from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.com). Signed-off-by: Sebastian Haas <haas@ems-wuensche.com> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: sja1000: legacy SJA1000 ISA bus driverWolfgang Grandegger2009-09-041-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for legacy SJA1000 CAN controllers on the ISA or PC-104 bus. The I/O port or memory address and the IRQ number must be specified via module parameters: insmod sja1000_isa.ko port=0x310,0x380 irq=7,11 for ISA devices using I/O ports or: insmod sja1000_isa.ko mem=0xd1000,0xd1000 irq=7,11 for memory mapped ISA devices. Indirect access via address and data port is supported as well: insmod sja1000_isa.ko port=0x310,0x380 indirect=1 irq=7,11 Here is a full list of the supported module parameters: port:I/O port number (array of ulong) mem:I/O memory address (array of ulong) indirect:Indirect access via address and data port (array of byte) irq:IRQ number (array of int) clk:External oscillator clock frequency (default=16000000 [16 MHz]) (array of int) cdr:Clock divider register (default=0x48 [CDR_CBP | CDR_CLK_OFF]) (array of byte) ocr:Output clock register (default=0x18 [OCR_TX0_PUSHPULL]) (array of byte) Note: for clk, cdr, ocr, the first argument re-defines the default for all other devices, e.g.: insmod sja1000_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000 is equivalent to insmod sja1000_isa.ko mem=0xd1000,0xd1000 irq=7,11 \ clk=24000000,24000000 Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Tested-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: sja1000: Add support for the new 4 channel EMS CPC-PCI cardsSebastian Haas2009-07-231-3/+4
| | | | | | | | | This patch adds support to the ems_pci driver for the new, v2, 4 channel CPC-PCI/PCIe/104P CAN cards from EMS Dr. Thomas Wuensche. Signed-off-by: Sebastian Haas <haas@ems-wuensche.com> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: let SJA1000 driver depend on HAS_IOMEMHeiko Carstens2009-06-231-1/+1
| | | | | | | | | | | | | | | | Fixes this compile error on s390: drivers/net/can/sja1000/sja1000_platform.c: In function 'sp_read_reg': drivers/net/can/sja1000/sja1000_platform.c:42: error: implicit declaration of function 'ioread8' drivers/net/can/sja1000/sja1000_platform.c: In function 'sp_write_reg': drivers/net/can/sja1000/sja1000_platform.c:47: error: implicit declaration of function 'iowrite8' drivers/net/can/sja1000/sja1000_platform.c: In function 'sp_probe': drivers/net/can/sja1000/sja1000_platform.c:79: error: implicit declaration of function 'ioremap_nocache' Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Oliver Hartkopp <oliver.hartkopp@volkswagen.de> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: sja1000: generic OF platform bus driverWolfgang Grandegger2009-06-011-0/+9
| | | | | | | | | | | | | | | | | | | | This patch adds a generic driver for SJA1000 chips on the OpenFirmware platform bus found on embedded PowerPC systems. You need a SJA1000 node definition in your flattened device tree source (DTS) file similar to: can@3,100 { compatible = "nxp,sja1000"; reg = <3 0x100 0x80>; interrupts = <2 0>; interrupt-parent = <&mpic>; nxp,external-clock-frequency = <16000000>; }; See also Documentation/powerpc/dts-bindings/can/sja1000.txt. CC: devicetree-discuss@ozlabs.org Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* The patch adds support for the PCI cards: PCIcan and PCIcanx (1, 2 or 4 ↵Wolfgang Grandegger2009-05-181-0/+7
| | | | | | | | channel) from Kvaser (http://www.kvaser.com). Signed-off-by: Per Dalen <per.dalen@cnw.se> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: SJA1000 driver for EMS PCI cardsWolfgang Grandegger2009-05-181-0/+7
| | | | | | | | | | The patch adds support for the one or two channel CPC-PCI and CPC-PCIe cards from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de). Signed-off-by: Sebastian Haas <haas@ems-wuensche.com> Signed-off-by: Markus Plessing <plessing@ems-wuensche.com> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: SJA1000 generic platform bus driverWolfgang Grandegger2009-05-181-0/+10
| | | | | | | | | | | This driver adds support for the SJA1000 chips connected to the "platform bus", which can be found on various embedded systems. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: Driver for the SJA1000 CAN controllerWolfgang Grandegger2009-05-181-0/+6
| | | | | | | | | This patch adds the generic Socket-CAN driver for the Philips SJA1000 full CAN controller. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: CAN Network device driver and Netlink interfaceWolfgang Grandegger2009-05-181-0/+23
| | | | | | | | | | | | | | | | | The CAN network device driver interface provides a generic interface to setup, configure and monitor CAN network devices. It exports a set of common data structures and functions, which all real CAN network device drivers should use. Please have a look to the SJA1000 or MSCAN driver to understand how to use them. The name of the module is can-dev.ko. Furthermore, it adds a Netlink interface allowing to configure the CAN device using the program "ip" from the iproute2 utility suite. For further information please check "Documentation/networking/can.txt" Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* [CAN]: Add virtual CAN netdevice driverOliver Hartkopp2008-01-281-0/+25
This patch adds the virtual CAN bus (vcan) network driver. The vcan device is just a loopback device for CAN frames, no real CAN hardware is involved. Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de> Signed-off-by: Urs Thuermann <urs.thuermann@volkswagen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.1 at 2024-12-27 03:24:10 +0000