aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/regulator/twl-regulator.c
Commit message (Collapse)AuthorAgeFilesLines
* regulator: twl: add clk32kg to twl-regulatorBalaji T K2011-03-231-1/+23
| | | | | | | | | | | | In OMAP4 Blaze and Panda, 32KHz clock to WLAN is supplied from Phoenix TWL6030. The 32KHz clock state (ON/OFF) is configured in CLK32KG_CFG_[GRP, TRANS, STATE] register. This follows the same register programming model as other regulators in TWL6030. So add CLK32KG as pseudo regulator. Signed-off-by: Balaji T K <balajitk@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* regulator: Report actual configured voltage to set_voltage()Mark Brown2011-01-121-3/+8
| | | | | | | | | | | Change the interface used by set_voltage() to report the selected value to the regulator core in terms of a selector used by list_voltage(). This allows the regulator core to know the voltage that was chosen without having to do an explict get_voltage(), which would be much more expensive as it will generally access hardware. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: twl-regulator - fix twlreg_set_modeAxel Lin2010-11-301-3/+3
| | | | | | | | | | | | | | | | | | The Singular Message is 16 bits: DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0] Current implementation return immedially after sucessfuly write MSB part. To properly set mode, we need to write the complete message ( MSB and LSB ). In twl.h, now we have defines for PM Master module register offsets, use it instead of hard coded 0x15/0x16. Use "message & 0xff" to ensure we send correct value for LSB. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Tested-by: Lesly Arackal Manuel <leslyam@ti.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* twl6030: regulator: Remove vsel tables and use formula for calculationRajendra Nayak2010-05-251-47/+91
| | | | | | | | | | | | | | | | | | | | | | All twl6030 regulators can be programmed from 1.0v to 3.3v with 100mV steps. The below formula can be used to calculate the vsel values to be programmed in the VREG_VOLTAGE registers. Voltage(in mV) = 1000mv + 100mv * (vsel - 1) Ex: if vsel = 0x9, mV = 1000 + 100 * (9 -1) = 1800mV. This patch removes all existing VSEL tables for twl6030 adjustable regulators and just uses the formula directly for vsel calculations after verifing they fall in the allowed range. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* Regulators: twl-regulator - mark probe function as __devinitDmitry Torokhov2010-03-031-1/+1
| | | | | | Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* twl6030: regulator: Configure STATE register instead of REMAPRajendra Nayak2010-03-031-10/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | This is no REMAP register on twl6030, instead there is a STATE register to drive a resource to a given state. The state register can be used to specify what state the resource should enter when its associated with a GRP. Register Bit field description is as below. The patch programmes the corresponding STATE registers for all LDO's to turn ON when assocaited with GRP_P1. STATE REG: Bit7 |Bit6 |Bit5 |Bit4 |Bit3 |Bit2 |Bit1 |Bit0 P3_GRP |P2_GRP |P1_GRP |RES |RES |RES |State1 |State0 State can be specified as below 00: OFF 01: ON 10: OFF 11: SLEEP Signed-off-by: Rajendra Nayak <rnayak@ti.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* twl-regulator: Fix reg_disable functionality for 4030 and 6030Juha Keski-Saari2009-12-171-2/+2
| | | | | | | | | This change makes sure all regulator group assignments are cleared on disable call Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* twl-regulator: Add turnon delay to reg_enableJuha Keski-Saari2009-12-171-1/+7
| | | | | | | | | | This change implements a basic turnon delay in the regulator enable function to make it less probable that reg_enable returns before the regulator output is at target level Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* twl-regulator: Restore REMAP configuration in regulator probeJuha Keski-Saari2009-12-171-0/+3
| | | | | | | | | | This change ensures the regulator REMAP register configuration is in a known state so state transitions will function as intended regardless of possible bootloader effects on it Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* twl-regulator: Add turnon-delay and REMAP config to twlreg_info structJuha Keski-Saari2009-12-171-41/+62
| | | | | | | | | | This change includes regulator turnon delay values and the REMAP reset configuration to the twlreg_info struct, since they are basic attributes of every TWL regulator Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* twl-regulator: Define critical regulators as always_onJuha Keski-Saari2009-12-171-0/+13
| | | | | | | | | | Defines VIO, VDD1, VDD2, VPLL1 and VINT* regulators as always_on by default since they are critical to TWL and its master's functionality and should be on in all cases where RegFW is used Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* twl-regulator: Add all twl4030 regulators to twlreg_infoJuha Keski-Saari2009-12-171-9/+17
| | | | | | | | | Define all twl4030 regulators in the twlreg_info table, along with appropriate VSEL tables for adjustable regulators Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Add support for twl6030 regulatorsRajendra Nayak2009-12-141-21/+95
| | | | | | | | | | | | | | This patch updates the regulator driver to add support for TWL6030 PMIC specific LDO regulators. SMPS resources are not yet supported for TWL6030 and also .set_mode and .get_status for LDO's are yet to be implemented for TWL6030. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Rename twl4030_ routines in twl-regulator.cRajendra Nayak2009-12-131-92/+97
| | | | | | | | | | | | This patch renames all twl4030_ functions to twl so that regulator driver can be reused by Triton - TWL4030 and Phoenix - TWL6030. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Rename all twl4030_i2c*Balaji T K2009-12-131-4/+4
| | | | | | | | | | | | This patch renames function names like twl4030_i2c_write_u8, twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8 and also common variable in twl-core.c Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Rename twl4030* driver files to enable re-useSantosh Shilimkar2009-12-131-0/+500
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030 for OMAP3. The common modules like RTC, Regulator creates opportunity to re-use the most of the code from twl4030. This patch renames few common drivers twl4030* files to twl* to enable the code re-use. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
generated by cgit v1.1 at 2024-10-27 14:22:44 +0000