aboutsummaryrefslogtreecommitdiffstats
path: root/include/linux/mtd
Commit message (Collapse)AuthorAgeFilesLines
* mtd: add writebufsize field to mtd_info structAnatolij Gustschin2011-01-061-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This field will be used to indicate the write buffer size of the MTD device. UBI will set it's minimal I/O unit size (min_io_size) to the indicated write buffer size. By this change we intend to fix failed recovery of UBIFS partitions we currently observe on NOR flash when mounting the partition after unclean unmount. Currently the min_io_size is set to mtd->writesize (which is 1 byte for NOR flash). But flash programming is often done from prepared write buffer containing multiple bytes and is performed in one programming operation which could be interrupted by a power cut or a system reset causing corrupted (partially written) areas in a flash sector. Knowing the size of potentially corrupted areas UBIFS scanning and recovery algorithms are able to perform successful recovery. In case of NOR flash minimal I/O size must be equal to the maximal size of the write buffer used by embedded flash programming algorithm. In case of NAND flash mtd->writebufsize should be equivalent to mtd->writesize. The subsequent patches will add mtd->writebufsize initialization where needed. Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: OneNAND: add enable / disable methods to onenand_chipAdrian Hunter2011-01-061-0/+2
| | | | | | | | | Add enable / disable methods called from get_device() / release_device(). These can be used, for example, to allow the driver to prevent the voltage regulator from being put to sleep while OneNAND is in use. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: FSMC NAND fix obvious speling errorsLinus Walleij2010-12-031-3/+3
| | | | | | | Fix spelling in the interface file. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: FSMC NAND use the PrimeCell identifier macrosLinus Walleij2010-12-031-19/+0
| | | | | | | | | | The FSMC actually has a standard ARM PrimeCell ID register, and the "revision" part of that register contains the thing that the code is looking at. Reuse the infrastructure from the AMBA bus abstraction and rid local defines. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: fix master device identification for mtd repartitionRoman Tereshonkov2010-12-031-1/+1
| | | | | | | | | | | Function mtd_has_master renamed as mtd_is_partition to follow the function logic. The patch fixes the problem of checking the right mtd device for partition creation. To delete partition checking is not needed here so as it is done in mtd_del_partition. By master we consider the mtd device which does not belong to any partition. Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: fix nand kernel-doc warningsRandy Dunlap2010-12-031-0/+2
| | | | | | | | | | | Warning(include/linux/mtd/nand.h:543): No description found for parameter 'badblockbits' Warning(drivers/mtd/nand/nand_bbt.c:1101): No description found for parameter 'mtd' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: linux-mtd@lists.infradead.org Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: cfi_fixup: remove unused 'param' parameterGuillaume LECERF2010-12-031-2/+1
| | | | | | | | | The 'param' parameter has never been used since its introduction, so simply remove it. Signed-off-by: Guillaume LECERF <glecerf@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: fsmc.h: including linux/io.h for definition of readlViresh Kumar2010-12-031-0/+1
| | | | | | Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: onenand: add option and variable for cache program featureRoman Tereshonkov2010-12-031-0/+12
| | | | | | | | | | | A new option is added for cache program feature. A new variable ongoing is introduced for onenand_chip to handle the multi-command cache program operation. Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* Merge git://git.infradead.org/mtd-2.6Linus Torvalds2010-10-307-169/+479
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.infradead.org/mtd-2.6: (82 commits) mtd: fix build error in m25p80.c mtd: Remove redundant mutex from mtd_blkdevs.c MTD: Fix wrong check register_blkdev return value Revert "mtd: cleanup Kconfig dependencies" mtd: cfi_cmdset_0002: make sector erase command variable mtd: cfi_cmdset_0002: add CFI detection for SST 38VF640x chips mtd: cfi_util: add support for switching SST 39VF640xB chips into QRY mode mtd: cfi_cmdset_0001: use defined value of P_ID_INTEL_PERFORMANCE instead of hardcoded one block2mtd: dubious assignment P4080/mtd: Fix the freescale lbc issue with 36bit mode P4080/eLBC: Make Freescale elbc interrupt common to elbc devices mtd: phram: use KBUILD_MODNAME mtd: OneNAND: S5PC110: Fix double call suspend & resume function mtd: nand: fix MTD_MODE_RAW writes jffs2: use kmemdup mtd: sm_ftl: cosmetic, use bool when possible mtd: r852: remove useless pci powerup/down from suspend/resume routines mtd: blktrans: fix a race vs kthread_stop mtd: blktrans: kill BKL mtd: allow to unload the mtdtrans module if its block devices aren't open ... Fix up trivial whitespace-introduced conflict in drivers/mtd/mtdchar.c
| * mtd: cfi_cmdset_0002: make sector erase command variableGuillaume LECERF2010-10-261-0/+1
| | | | | | | | | | | | | | | | | | Some old SST chips use 0x50 as sector erase command, instead of 0x30. Make this value variable to handle such chips. Signed-off-by: Guillaume LECERF <glecerf@gmail.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
| * mtd: remove junk tabs in nand.hSebastian Andrzej Siewior2010-10-251-168/+147
| | | | | | | | | | | | | | | | Remove tabs between type and name. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
| * mtd: cleanup nand.hSebastian Andrzej Siewior2010-10-251-56/+99
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - *var instead of * var - proper multiline comment - func(args) instead of func (args) - 80 lines So from |total: 2 errors, 37 warnings, 654 lines checked we got to one warning. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
| * mtd: nand: introduce NAND_CREATE_EMPTY_BBTSebastian Andrzej Siewior2010-10-252-1/+3
| | | | | | | | | | | | | | | | | | | | it will create an empty BBT table without considering vendor's BBT information. Vendor's information may be unavailable if the NAND controller has a different DATA & OOB layout or this information may be allready purged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
| * mtd: nand: add support for BBT without OOBSebastian Andrzej Siewior2010-10-252-2/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The first (sixt) byte in the OOB area contains vendor's bad block information. During identification of the NAND chip this information is collected by scanning the complete chip. The option NAND_USE_FLASH_BBT is used to store this information in a sector so we don't have to scan the complete flash. Unfortunately the code stores a marker in order to recognize the BBT in the OOB area. This will fail if the OOB area is completely used for ECC. This patch introduces the option NAND_USE_FLASH_BBT_NO_OOB which has to be used with NAND_USE_FLASH_BBT. It will then store BBT on flash without touching the OOB area. The BBT format on flash remains same except the first page starts with the recognition pattern followed by the version byte. This change was tested in nandsim and it looks good so far :) Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
| * mtd: add init_size hook for NAND driverHuang Shijie2010-10-251-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Not all the NAND devices have all the information in additional id bytes. So add a hook in the nand_chip{} is a good method to calculate the right value of oobsize, erasesize and so on. Without the hook,you will get the wrong value, and you have to hack in the ->scan_bbt() to change the wrong value which make the code mess. Signed-off-by: Huang Shijie <shijie8@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
| * mtd: prepare partition add and del functions for ioctl requestsRoman Tereshonkov2010-10-251-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | mtd_is_master, mtd_add_partition and mtd_del_partition functions are added to give the possibility of partition manipulation by ioctl request. The old partition add function is modified to fit the dynamic allocation. Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
| * mtd: generic FSMC NAND MTD driverLinus Walleij2010-10-251-0/+181
| | | | | | | | | | | | | | | | | | | | | | | | | | This is the same driver submitted by ST Micros SPEAr team but generalized and tested on the ST-Ericsson U300. It probably easily works on the NHK8815 too. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com> Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
| * mtd: nand: add support for reading ONFI parameters from NAND deviceFlorian Fainelli2010-10-241-0/+68
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for reading NAND device ONFI parameters and use the ONFI informations to define its geometry. In case the device supports ONFI, the onfi_version field in struct nand_chip contains the version (BCD) and the onfi_params structure can be used by drivers to set up timings and such. We currently only support ONFI 1.0 parameters. Signed-off-by: Brian Norris <norris@broadcom.com> Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com> Signed-off-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Florian Fainelli <ffainelli@freebox.fr> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
| * mtd: nand: add NAND_CMD_PARAM (0xec) definitionFlorian Fainelli2010-10-241-0/+1
| | | | | | | | | | | | | | This command is used to read the device ONFI parameters page. Signed-off-by: Florian Fainelli <ffainelli@freebox.fr> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
| * mtd: nand: Increase NAND_MAX_OOBSIZEBrian Norris2010-10-241-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | An increase in NAND_MAX_OOBSIZE and NAND_MAX_PAGESIZE is necessary in order to support many new chips. Among those: Toshiba TC58TxG4S2FBAxx 8KB page, 576B OOB Micron MT29F64G08CBAAA 8KB page, 448B OOB Signed-off-by: Brian Norris <norris@broadcom.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
| * mtd: edit comments on deprecation of ioctl ECCGETLAYOUTBrian Norris2010-10-241-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There were some improvements and additions necessary in the comments explaining of the expansion of nand_ecclayout, the introduction of nand_ecclayout_user, and the deprecation of the ioctl ECCGETLAYOUT. Also, I found a better placement for the macro MTD_MAX_ECCPOS_ENTRIES; next to the definition of MTD_MAX_OOBFREE_ENTRIES in mtd-abi.h. The macro is really only important for the ioctl code (found in drivers/mtd/mtdchar.c) but since there are small edits being made to the user-space header, I figured this is a better location. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
| * mtd: nand: expand nand_ecc_layout, deprecate ioctl ECCGETLAYOUTBrian Norris2010-10-242-1/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | struct nand_ecclayout is too small for many new chips; OOB regions can be as large as 448 bytes and may increase more in the future. Thus, copying that struct to user-space with the ECCGETLAYOUT ioctl is not a good idea; the ioctl would have to be updated every time there's a change to the current largest size. Instead, the old nand_ecclayout is renamed to nand_ecclayout_user and a new struct nand_ecclayout is created that can accomodate larger sizes and expand without affecting the user-space. struct nand_ecclayout can still be used in board drivers without modification -- at least for now. A new function is provided to convert from the new to the old in order to allow the deprecated ioctl to continue to work with truncated data. Perhaps the ioctl, the conversion process, and the struct nand_ecclayout_user can be removed altogether in the future. Note: There are comments in nand/davinci_nand.c::nand_davinci_probe() regarding this issue; this driver (and maybe others) can be updated to account for extra space. All kernel drivers can use the expanded nand_ecclayout as a drop-in replacement and ignore its benefits. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
| * mtd: inftl.h: fix spacing errorsBrian Norris2010-10-241-7/+7
| | | | | | | | | | | | | | | | Replaced some spaces with tabs to fit CodingStyle guidelines Signed-off-by: Brian Norris <norris@broadcom.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* | convert get_sb_mtd() users to ->mount()Al Viro2010-10-291-3/+2
|/ | | | Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* mtd: Remove obsolete <mtd/compatmac.h> includeDavid Woodhouse2010-08-083-12/+0
| | | | Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: Update copyright noticesDavid Woodhouse2010-08-0813-27/+186
| | | | Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* mtd-physmap: add support users can assign the probe type in board filesBarry Song2010-08-081-0/+1
| | | | | | | | | | | | | | | | There are three reasons to add this support: 1. users probably know the interface type of their flashs, then probe can be faster if they give the right type in platform data since wrong types will not be detected. 2. sometimes, detecting can cause destory to system. For example, for kernel XIP, detecting can cause NOR enter a mode instructions can not be fetched right, which will make kernel crash. 3. For a new probe which is not listed in the rom_probe_types, if users assign it in board files, physmap can still probe it. Signed-off-by: Barry Song <21cnbao@gmail.com> Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: change struct flchip_shared spinlock locking into mutexStefani Seibold2010-08-061-1/+1
| | | | | | | | | | | | This patch prevent to schedule while atomic by changing the flchip_shared spinlock into a mutex. This should be save since no atomic path will use this lock. It was suggested by Arnd Bergmann and Vasiliy Kulikov. Signed-off-by: Stefani Seibold <stefani@seibold.net> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: OneNAND: Introduce chip_probe functionKyungmin Park2010-08-041-0/+2
| | | | | | | | | | Samsung SoCs use the own OneNAND controler and detect OneNAND chip at power on. To use this feature, introduce the chip_probe function. Also remove workaround for Samsung SoCs. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: nand: more BB Detection refactoring and dynamic scan optionsBrian Norris2010-08-021-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a revision to PATCH 2/2 that I sent. Link: http://lists.infradead.org/pipermail/linux-mtd/2010-July/030911.html Added new flag for scanning of both bytes 1 and 6 of the OOB for a BB marker (instead of simply one or the other). The "check_pattern" and "check_short_pattern" functions were updated to include support for scanning the two different locations in the OOB. In order to handle increases in variety of necessary scanning patterns, I implemented dynamic memory allocation of nand_bbt_descr structs in new function 'nand_create_default_bbt_descr()'. This replaces some increasingly-unwieldy, statically-declared descriptors. It can replace several more (e.g. "flashbased" structs). However, I do not test the flashbased options personally. How this was tested: I referenced 30+ data sheets (covering 100+ parts), and I tested a selection of 10 different chips to varying degrees. Particularly, I tested the creation of bad-block descriptors and basic BB scanning on three parts: ST NAND04GW3B2D, 2K page ST NAND128W3A, 512B page Samsung K9F1G08U0A, 2K page To test these, I wrote some fake bad block markers to the flash (in OOB bytes 1, 6, and elsewhere) to see if the scanning routine would detect them properly. However, this method was somewhat limited because the driver I am using has some bugs in its OOB write functionality. Signed-off-by: Brian Norris <norris@broadcom.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: nand: edit macro flag for BBT scan of last page in blockBrian Norris2010-08-022-2/+2
| | | | | | | | | | | | NAND_BB_LAST_PAGE used to be in nand.h, but it pertained to bad block management and so belongs next to NAND_BBT_SCAN2NDPAGE in bbm.h. Also, its previous flag value (0x00000400) conflicted with NAND_BBT_SCANALLPAGES so I changed its value to 0x00008000. All uses of the name were modified to provide consistency with other "NAND_BBT_*" flags. Signed-off-by: Brian Norris <norris@broadcom.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: add an ioctl to query the lock status of a flash sectorRichard Cochran2010-08-021-0/+1
| | | | | | | | | | This patchs adds a way for user space programs to find out whether a flash sector is locked. An optional driver method in the mtd_info struct provides the information. Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: nand: support alternate BB marker locations on MLCKevin Cernekee2010-05-141-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a slightly modified version of a patch submitted last year by Reuben Dowle <reuben.dowle@navico.com>. His original comments follow: This patch adds support for some MLC NAND flashes that place the BB marker in the LAST page of the bad block rather than the FIRST page used for SLC NAND and other types of MLC nand. Lifted from Samsung datasheet for K9LG8G08U0A (1Gbyte MLC NAND): " Identifying Initial Invalid Block(s) All device locations are erased(FFh) except locations where the initial invalid block(s) information is written prior to shipping. The initial invalid block(s) status is defined by the 1st byte in the spare area. Samsung makes sure that the last page of every initial invalid block has non-FFh data at the column address of 2,048. ... " As far as I can tell, this is the same for all Samsung MLC nand, and in fact the samsung bsp for the processor used in our project (s3c6410) actually contained a hack similar to this patch but less portable to enable use of their NAND parts. I discovered this problem when trying to use a Micron NAND which does not used this layout - I wish samsung would put their stuff in main-line to avoid this type of problem. Currently this patch causes all MLC nand with manufacturer codes from Samsung and ST(Numonyx) to use this alternative location, since these are the manufactures that I know of that use this layout. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: nand: extend NAND flash detection to new MLC chipsKevin Cernekee2010-05-141-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some of the newer MLC devices have a 6-byte ID sequence in which several field definitions differ from older chips in a manner that is not backward compatible. For instance: Samsung K9GAG08U0M (5-byte sequence): ec d5 14 b6 74 4th byte, bits 1:0 encode the page size: 0=1KiB, 1=2KiB, 2=4KiB, 3=8KiB 4th byte, bits 5:4 encode the block size: 0=64KiB, 1=128KiB, ... 4th byte, bit 6 encodes the OOB size: 0=8B/512B, 1=16B/512B Samsung K9GAG08U0D (6-byte sequence): ec d5 94 29 34 41 4th byte, bits 1:0 encode the page size: 0=2KiB, 1=4KiB, 3=8KiB, 4=rsvd 4th byte, bits 7;5:4 encode the block size: 0=128KiB, 1=256KiB, ... 4th byte, bits 6;3:2 encode the OOB size: 1=128B/page, 2=218B/page This patch uses the new 6-byte scheme if the following conditions are all true: 1) The ID code wraps around after exactly 6 bytes 2) Manufacturer is Samsung 3) 6th byte is zero The patch also extends the maximum OOB size from 128B to 256B. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: suppress warnings in inline_map_read()Kevin Cernekee2010-05-141-0/+2
| | | | | | | | | | | | | | With gcc 4.4.3 -O2 on MIPS32: drivers/mtd/chips/cfi_util.c: In function 'cfi_qry_present': include/linux/mtd/map.h:390: warning: 'r' may be used uninitialized in this function include/linux/mtd/map.h:375: note: 'r' was declared here include/linux/mtd/map.h:390: warning: 'r' may be used uninitialized in this function include/linux/mtd/map.h:375: note: 'r' was declared here Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: map.h: add missing bug.h includeKevin Cernekee2010-05-141-0/+1
| | | | | | Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: onenand: add new callback for bufferram readKyungmin Park2010-05-141-0/+2
| | | | | | | | | | | This patch adds a new callback for the underlying drivers, which is called instead of accessing the buffer ram directly. This callback will be used by Samsung OneNAND driver to implement DMA transfers on S5PC110 SoC. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: onenand: allocate verify buffer in the coreKyungmin Park2010-05-141-0/+3
| | | | | | | | | | This patch extends OneNAND core code with support for OneNAND verify write check. This is done by allocating the buffer for verify read directly from the core code. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: onenand: add support for chips with 4KiB page sizeKyungmin Park2010-05-141-0/+4
| | | | | | | | This patch adds support for OneNAND chips that have 4KiB page size. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: chips: use common manufacturer codes in jedec_probe()Wolfram Sang2010-05-141-2/+11
| | | | | | | Factor out old manufacturers and use the generic ones from cfi.h Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: cfi_probe: add support for SST 0x0701 vendornameGuillaume LECERF2010-05-141-0/+1
| | | | | | | | | SST 39VF160x and 39VF320x chips use vendorname id 0x0701 and alternative unlock addresses. Add support for them in cfi_probe.c. Signed-off-by: Guillaume LECERF <glecerf@gmail.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd/nand/sh_flctl: Move function mtd_to_flctl to fix build failurePeter Huewe2010-05-121-5/+5
| | | | | | | | | | | This patch fixes a build failure[1] by simply moving the function mtd_to_flctl beneath the definition of sh_flctl which it uses. BF introduced by patch 'mtd/nand/sh_flctl: Replace the dangerous mtd_to_flctl macro' (67026418) Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: fix a huge latency problem in the MTD CFI and LPDDR flash drivers.Stefani Seibold2010-05-101-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The use of a memcpy() during a spinlock operation will cause very long thread context switch delays if the flash chip bandwidth is low and the data to be copied large, because a spinlock will disable preemption. For example: A flash with 6,5 MB/s bandwidth will cause under ubifs, which request sometimes 128 KiB (the flash erase size), a preemption delay of 20 milliseconds. High priority threads will not be served during this time, regardless whether this threads access the flash or not. This behavior breaks real time. The patch changes all the use of spin_lock operations for xxxx->mutex into mutex operations, which is exact what the name says and means. I have checked the code of the drivers and there is no use of atomic pathes like interrupt or timers. The mtdoops facility will also not be used by this drivers. So it is dave to replace the spin_lock against mutex. There is no performance regression since the mutex is normally not acquired. Changelog: 06.03.2010 First release 26.03.2010 Fix mutex[1] issue and tested it for compile failure Signed-off-by: Stefani Seibold <stefani@seibold.net> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd/nand/sh_flctl: Replace the dangerous mtd_to_flctl macroFerenc Wagner2010-05-101-1/+4
| | | | | | | | | | The original macro worked only when applied to variables named 'mtd'. While this could have been fixed by simply renaming the macro argument, a more type-safe replacement is preferred. Signed-off-by: Ferenc Wagner <wferi@niif.hu> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* mtd: mtdram.h: checkpatch cleanupAndrea Gelmini2010-05-101-1/+1
| | | | | | | | include/linux/mtd/mtdram.h:6: ERROR: code indent should use tabs where possible Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* Merge branch 'master' of ↵David Woodhouse2010-03-261-0/+3
|\ | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 Conflicts: drivers/mtd/nand/sh_flctl.c Maxim's patch to initialise sysfs attributes depends on the patch which actually adds sysfs_attr_init().
| * mtd: sh_flctl SHBUSSEL and SEL_16BIT supportMagnus Damm2010-02-021-0/+2
| | | | | | | | | | | | | | | | | | | | This patch extends the sh_flctl driver with support for 16-bit bus configuration using SEL_16BIT and support for multiplexed pins using SHBUSSEL. Signed-off-by: Magnus Damm <damm@opensource.se> Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
| * mtd: trivial sh_flctl changesMagnus Damm2010-02-021-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | This patch contains a few changes for the sh_flctl driver: - not sh7723-only driver - get rid of kconfig dependency - use dev_err() instead of printk() - use __devinit and __devexit for probe()/remove() - fix probe() return values Signed-off-by: Magnus Damm <damm@opensource.se> Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* | Merge branch 'master' of ↵David Woodhouse2010-02-261-0/+17
|\ \ | |/ | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 The SmartMedia FTL code depends on new kfifo bits from 2.6.33
generated by cgit v1.1 at 2024-12-25 14:33:32 +0000