diff options
Diffstat (limited to 'binutils-2.20.1/gas/doc/as.info')
-rw-r--r-- | binutils-2.20.1/gas/doc/as.info | 22076 |
1 files changed, 22076 insertions, 0 deletions
diff --git a/binutils-2.20.1/gas/doc/as.info b/binutils-2.20.1/gas/doc/as.info new file mode 100644 index 0000000..4f4af95 --- /dev/null +++ b/binutils-2.20.1/gas/doc/as.info @@ -0,0 +1,22076 @@ +This is as.info, produced by makeinfo version 4.8 from as.texinfo. + +START-INFO-DIR-ENTRY +* As: (as). The GNU assembler. +* Gas: (as). The GNU assembler. +END-INFO-DIR-ENTRY + + This file documents the GNU Assembler "as". + + Copyright (C) 1991, 92, 93, 94, 95, 96, 97, 98, 99, 2000, 2001, 2002, +2006, 2007, 2008, 2009 Free Software Foundation, Inc. + + Permission is granted to copy, distribute and/or modify this document +under the terms of the GNU Free Documentation License, Version 1.3 or +any later version published by the Free Software Foundation; with no +Invariant Sections, with no Front-Cover Texts, and with no Back-Cover +Texts. A copy of the license is included in the section entitled "GNU +Free Documentation License". + + +File: as.info, Node: Top, Next: Overview, Up: (dir) + +Using as +******** + +This file is a user guide to the GNU assembler `as' (GNU Binutils) +version 2.20.1. + + This document is distributed under the terms of the GNU Free +Documentation License. A copy of the license is included in the +section entitled "GNU Free Documentation License". + +* Menu: + +* Overview:: Overview +* Invoking:: Command-Line Options +* Syntax:: Syntax +* Sections:: Sections and Relocation +* Symbols:: Symbols +* Expressions:: Expressions +* Pseudo Ops:: Assembler Directives + +* Object Attributes:: Object Attributes +* Machine Dependencies:: Machine Dependent Features +* Reporting Bugs:: Reporting Bugs +* Acknowledgements:: Who Did What +* GNU Free Documentation License:: GNU Free Documentation License +* AS Index:: AS Index + + +File: as.info, Node: Overview, Next: Invoking, Prev: Top, Up: Top + +1 Overview +********** + +Here is a brief summary of how to invoke `as'. For details, see *Note +Command-Line Options: Invoking. + + as [-a[cdghlns][=FILE]] [-alternate] [-D] + [-debug-prefix-map OLD=NEW] + [-defsym SYM=VAL] [-f] [-g] [-gstabs] + [-gstabs+] [-gdwarf-2] [-help] [-I DIR] [-J] + [-K] [-L] [-listing-lhs-width=NUM] + [-listing-lhs-width2=NUM] [-listing-rhs-width=NUM] + [-listing-cont-lines=NUM] [-keep-locals] [-o + OBJFILE] [-R] [-reduce-memory-overheads] [-statistics] + [-v] [-version] [-version] [-W] [-warn] + [-fatal-warnings] [-w] [-x] [-Z] [@FILE] + [-target-help] [TARGET-OPTIONS] + [-|FILES ...] + + _Target Alpha options:_ + [-mCPU] + [-mdebug | -no-mdebug] + [-replace | -noreplace] + [-relax] [-g] [-GSIZE] + [-F] [-32addr] + + _Target ARC options:_ + [-marc[5|6|7|8]] + [-EB|-EL] + + _Target ARM options:_ + [-mcpu=PROCESSOR[+EXTENSION...]] + [-march=ARCHITECTURE[+EXTENSION...]] + [-mfpu=FLOATING-POINT-FORMAT] + [-mfloat-abi=ABI] + [-meabi=VER] + [-mthumb] + [-EB|-EL] + [-mapcs-32|-mapcs-26|-mapcs-float| + -mapcs-reentrant] + [-mthumb-interwork] [-k] + + _Target CRIS options:_ + [-underscore | -no-underscore] + [-pic] [-N] + [-emulation=criself | -emulation=crisaout] + [-march=v0_v10 | -march=v10 | -march=v32 | -march=common_v10_v32] + + _Target D10V options:_ + [-O] + + _Target D30V options:_ + [-O|-n|-N] + + _Target H8/300 options:_ + [-h-tick-hex] + + _Target i386 options:_ + [-32|-64] [-n] + [-march=CPU[+EXTENSION...]] [-mtune=CPU] + + _Target i960 options:_ + [-ACA|-ACA_A|-ACB|-ACC|-AKA|-AKB| + -AKC|-AMC] + [-b] [-no-relax] + + _Target IA-64 options:_ + [-mconstant-gp|-mauto-pic] + [-milp32|-milp64|-mlp64|-mp64] + [-mle|mbe] + [-mtune=itanium1|-mtune=itanium2] + [-munwind-check=warning|-munwind-check=error] + [-mhint.b=ok|-mhint.b=warning|-mhint.b=error] + [-x|-xexplicit] [-xauto] [-xdebug] + + _Target IP2K options:_ + [-mip2022|-mip2022ext] + + _Target M32C options:_ + [-m32c|-m16c] [-relax] [-h-tick-hex] + + _Target M32R options:_ + [-m32rx|-[no-]warn-explicit-parallel-conflicts| + -W[n]p] + + _Target M680X0 options:_ + [-l] [-m68000|-m68010|-m68020|...] + + _Target M68HC11 options:_ + [-m68hc11|-m68hc12|-m68hcs12] + [-mshort|-mlong] + [-mshort-double|-mlong-double] + [-force-long-branches] [-short-branches] + [-strict-direct-mode] [-print-insn-syntax] + [-print-opcodes] [-generate-example] + + _Target MCORE options:_ + [-jsri2bsr] [-sifilter] [-relax] + [-mcpu=[210|340]] + _Target MICROBLAZE options:_ + + _Target MIPS options:_ + [-nocpp] [-EL] [-EB] [-O[OPTIMIZATION LEVEL]] + [-g[DEBUG LEVEL]] [-G NUM] [-KPIC] [-call_shared] + [-non_shared] [-xgot [-mvxworks-pic] + [-mabi=ABI] [-32] [-n32] [-64] [-mfp32] [-mgp32] + [-march=CPU] [-mtune=CPU] [-mips1] [-mips2] + [-mips3] [-mips4] [-mips5] [-mips32] [-mips32r2] + [-mips64] [-mips64r2] + [-construct-floats] [-no-construct-floats] + [-trap] [-no-break] [-break] [-no-trap] + [-mfix7000] [-mno-fix7000] + [-mips16] [-no-mips16] + [-msmartmips] [-mno-smartmips] + [-mips3d] [-no-mips3d] + [-mdmx] [-no-mdmx] + [-mdsp] [-mno-dsp] + [-mdspr2] [-mno-dspr2] + [-mmt] [-mno-mt] + [-mdebug] [-no-mdebug] + [-mpdr] [-mno-pdr] + + _Target MMIX options:_ + [-fixed-special-register-names] [-globalize-symbols] + [-gnu-syntax] [-relax] [-no-predefined-symbols] + [-no-expand] [-no-merge-gregs] [-x] + [-linker-allocated-gregs] + + _Target PDP11 options:_ + [-mpic|-mno-pic] [-mall] [-mno-extensions] + [-mEXTENSION|-mno-EXTENSION] + [-mCPU] [-mMACHINE] + + _Target picoJava options:_ + [-mb|-me] + + _Target PowerPC options:_ + [-mpwrx|-mpwr2|-mpwr|-m601|-mppc|-mppc32|-m603|-m604| + -m403|-m405|-mppc64|-m620|-mppc64bridge|-mbooke] + [-mcom|-many|-maltivec|-mvsx] [-memb] + [-mregnames|-mno-regnames] + [-mrelocatable|-mrelocatable-lib] + [-mlittle|-mlittle-endian|-mbig|-mbig-endian] + [-msolaris|-mno-solaris] + + _Target s390 options:_ + [-m31|-m64] [-mesa|-mzarch] [-march=CPU] + [-mregnames|-mno-regnames] + [-mwarn-areg-zero] + + _Target SCORE options:_ + [-EB][-EL][-FIXDD][-NWARN] + [-SCORE5][-SCORE5U][-SCORE7][-SCORE3] + [-march=score7][-march=score3] + [-USE_R1][-KPIC][-O0][-G NUM][-V] + + _Target SPARC options:_ + [-Av6|-Av7|-Av8|-Asparclet|-Asparclite + -Av8plus|-Av8plusa|-Av9|-Av9a] + [-xarch=v8plus|-xarch=v8plusa] [-bump] + [-32|-64] + + _Target TIC54X options:_ + [-mcpu=54[123589]|-mcpu=54[56]lp] [-mfar-mode|-mf] + [-merrors-to-file <FILENAME>|-me <FILENAME>] + + + _Target Z80 options:_ + [-z80] [-r800] + [ -ignore-undocumented-instructions] [-Wnud] + [ -ignore-unportable-instructions] [-Wnup] + [ -warn-undocumented-instructions] [-Wud] + [ -warn-unportable-instructions] [-Wup] + [ -forbid-undocumented-instructions] [-Fud] + [ -forbid-unportable-instructions] [-Fup] + + + _Target Xtensa options:_ + [-[no-]text-section-literals] [-[no-]absolute-literals] + [-[no-]target-align] [-[no-]longcalls] + [-[no-]transform] + [-rename-section OLDNAME=NEWNAME] + +`@FILE' + Read command-line options from FILE. The options read are + inserted in place of the original @FILE option. If FILE does not + exist, or cannot be read, then the option will be treated + literally, and not removed. + + Options in FILE are separated by whitespace. A whitespace + character may be included in an option by surrounding the entire + option in either single or double quotes. Any character + (including a backslash) may be included by prefixing the character + to be included with a backslash. The FILE may itself contain + additional @FILE options; any such options will be processed + recursively. + +`-a[cdghlmns]' + Turn on listings, in any of a variety of ways: + + `-ac' + omit false conditionals + + `-ad' + omit debugging directives + + `-ag' + include general information, like as version and options + passed + + `-ah' + include high-level source + + `-al' + include assembly + + `-am' + include macro expansions + + `-an' + omit forms processing + + `-as' + include symbols + + `=file' + set the name of the listing file + + You may combine these options; for example, use `-aln' for assembly + listing without forms processing. The `=file' option, if used, + must be the last one. By itself, `-a' defaults to `-ahls'. + +`--alternate' + Begin in alternate macro mode. *Note `.altmacro': Altmacro. + +`-D' + Ignored. This option is accepted for script compatibility with + calls to other assemblers. + +`--debug-prefix-map OLD=NEW' + When assembling files in directory `OLD', record debugging + information describing them as in `NEW' instead. + +`--defsym SYM=VALUE' + Define the symbol SYM to be VALUE before assembling the input file. + VALUE must be an integer constant. As in C, a leading `0x' + indicates a hexadecimal value, and a leading `0' indicates an octal + value. The value of the symbol can be overridden inside a source + file via the use of a `.set' pseudo-op. + +`-f' + "fast"--skip whitespace and comment preprocessing (assume source is + compiler output). + +`-g' +`--gen-debug' + Generate debugging information for each assembler source line + using whichever debug format is preferred by the target. This + currently means either STABS, ECOFF or DWARF2. + +`--gstabs' + Generate stabs debugging information for each assembler line. This + may help debugging assembler code, if the debugger can handle it. + +`--gstabs+' + Generate stabs debugging information for each assembler line, with + GNU extensions that probably only gdb can handle, and that could + make other debuggers crash or refuse to read your program. This + may help debugging assembler code. Currently the only GNU + extension is the location of the current working directory at + assembling time. + +`--gdwarf-2' + Generate DWARF2 debugging information for each assembler line. + This may help debugging assembler code, if the debugger can handle + it. Note--this option is only supported by some targets, not all + of them. + +`--help' + Print a summary of the command line options and exit. + +`--target-help' + Print a summary of all target specific options and exit. + +`-I DIR' + Add directory DIR to the search list for `.include' directives. + +`-J' + Don't warn about signed overflow. + +`-K' + Issue warnings when difference tables altered for long + displacements. + +`-L' +`--keep-locals' + Keep (in the symbol table) local symbols. These symbols start with + system-specific local label prefixes, typically `.L' for ELF + systems or `L' for traditional a.out systems. *Note Symbol + Names::. + +`--listing-lhs-width=NUMBER' + Set the maximum width, in words, of the output data column for an + assembler listing to NUMBER. + +`--listing-lhs-width2=NUMBER' + Set the maximum width, in words, of the output data column for + continuation lines in an assembler listing to NUMBER. + +`--listing-rhs-width=NUMBER' + Set the maximum width of an input source line, as displayed in a + listing, to NUMBER bytes. + +`--listing-cont-lines=NUMBER' + Set the maximum number of lines printed in a listing for a single + line of input to NUMBER + 1. + +`-o OBJFILE' + Name the object-file output from `as' OBJFILE. + +`-R' + Fold the data section into the text section. + + Set the default size of GAS's hash tables to a prime number close + to NUMBER. Increasing this value can reduce the length of time it + takes the assembler to perform its tasks, at the expense of + increasing the assembler's memory requirements. Similarly + reducing this value can reduce the memory requirements at the + expense of speed. + +`--reduce-memory-overheads' + This option reduces GAS's memory requirements, at the expense of + making the assembly processes slower. Currently this switch is a + synonym for `--hash-size=4051', but in the future it may have + other effects as well. + +`--statistics' + Print the maximum space (in bytes) and total time (in seconds) + used by assembly. + +`--strip-local-absolute' + Remove local absolute symbols from the outgoing symbol table. + +`-v' +`-version' + Print the `as' version. + +`--version' + Print the `as' version and exit. + +`-W' +`--no-warn' + Suppress warning messages. + +`--fatal-warnings' + Treat warnings as errors. + +`--warn' + Don't suppress warning messages or treat them as errors. + +`-w' + Ignored. + +`-x' + Ignored. + +`-Z' + Generate an object file even after errors. + +`-- | FILES ...' + Standard input, or source files to assemble. + + + The following options are available when as is configured for an ARC +processor. + +`-marc[5|6|7|8]' + This option selects the core processor variant. + +`-EB | -EL' + Select either big-endian (-EB) or little-endian (-EL) output. + + The following options are available when as is configured for the ARM +processor family. + +`-mcpu=PROCESSOR[+EXTENSION...]' + Specify which ARM processor variant is the target. + +`-march=ARCHITECTURE[+EXTENSION...]' + Specify which ARM architecture variant is used by the target. + +`-mfpu=FLOATING-POINT-FORMAT' + Select which Floating Point architecture is the target. + +`-mfloat-abi=ABI' + Select which floating point ABI is in use. + +`-mthumb' + Enable Thumb only instruction decoding. + +`-mapcs-32 | -mapcs-26 | -mapcs-float | -mapcs-reentrant' + Select which procedure calling convention is in use. + +`-EB | -EL' + Select either big-endian (-EB) or little-endian (-EL) output. + +`-mthumb-interwork' + Specify that the code has been generated with interworking between + Thumb and ARM code in mind. + +`-k' + Specify that PIC code has been generated. + + See the info pages for documentation of the CRIS-specific options. + + The following options are available when as is configured for a D10V +processor. +`-O' + Optimize output by parallelizing instructions. + + The following options are available when as is configured for a D30V +processor. +`-O' + Optimize output by parallelizing instructions. + +`-n' + Warn when nops are generated. + +`-N' + Warn when a nop after a 32-bit multiply instruction is generated. + + The following options are available when as is configured for the +Intel 80960 processor. + +`-ACA | -ACA_A | -ACB | -ACC | -AKA | -AKB | -AKC | -AMC' + Specify which variant of the 960 architecture is the target. + +`-b' + Add code to collect statistics about branches taken. + +`-no-relax' + Do not alter compare-and-branch instructions for long + displacements; error if necessary. + + + The following options are available when as is configured for the +Ubicom IP2K series. + +`-mip2022ext' + Specifies that the extended IP2022 instructions are allowed. + +`-mip2022' + Restores the default behaviour, which restricts the permitted + instructions to just the basic IP2022 ones. + + + The following options are available when as is configured for the +Renesas M32C and M16C processors. + +`-m32c' + Assemble M32C instructions. + +`-m16c' + Assemble M16C instructions (the default). + +`-relax' + Enable support for link-time relaxations. + +`-h-tick-hex' + Support H'00 style hex constants in addition to 0x00 style. + + + The following options are available when as is configured for the +Renesas M32R (formerly Mitsubishi M32R) series. + +`--m32rx' + Specify which processor in the M32R family is the target. The + default is normally the M32R, but this option changes it to the + M32RX. + +`--warn-explicit-parallel-conflicts or --Wp' + Produce warning messages when questionable parallel constructs are + encountered. + +`--no-warn-explicit-parallel-conflicts or --Wnp' + Do not produce warning messages when questionable parallel + constructs are encountered. + + + The following options are available when as is configured for the +Motorola 68000 series. + +`-l' + Shorten references to undefined symbols, to one word instead of + two. + +`-m68000 | -m68008 | -m68010 | -m68020 | -m68030' +`| -m68040 | -m68060 | -m68302 | -m68331 | -m68332' +`| -m68333 | -m68340 | -mcpu32 | -m5200' + Specify what processor in the 68000 family is the target. The + default is normally the 68020, but this can be changed at + configuration time. + +`-m68881 | -m68882 | -mno-68881 | -mno-68882' + The target machine does (or does not) have a floating-point + coprocessor. The default is to assume a coprocessor for 68020, + 68030, and cpu32. Although the basic 68000 is not compatible with + the 68881, a combination of the two can be specified, since it's + possible to do emulation of the coprocessor instructions with the + main processor. + +`-m68851 | -mno-68851' + The target machine does (or does not) have a memory-management + unit coprocessor. The default is to assume an MMU for 68020 and + up. + + + For details about the PDP-11 machine dependent features options, see +*Note PDP-11-Options::. + +`-mpic | -mno-pic' + Generate position-independent (or position-dependent) code. The + default is `-mpic'. + +`-mall' +`-mall-extensions' + Enable all instruction set extensions. This is the default. + +`-mno-extensions' + Disable all instruction set extensions. + +`-mEXTENSION | -mno-EXTENSION' + Enable (or disable) a particular instruction set extension. + +`-mCPU' + Enable the instruction set extensions supported by a particular + CPU, and disable all other extensions. + +`-mMACHINE' + Enable the instruction set extensions supported by a particular + machine model, and disable all other extensions. + + The following options are available when as is configured for a +picoJava processor. + +`-mb' + Generate "big endian" format output. + +`-ml' + Generate "little endian" format output. + + + The following options are available when as is configured for the +Motorola 68HC11 or 68HC12 series. + +`-m68hc11 | -m68hc12 | -m68hcs12' + Specify what processor is the target. The default is defined by + the configuration option when building the assembler. + +`-mshort' + Specify to use the 16-bit integer ABI. + +`-mlong' + Specify to use the 32-bit integer ABI. + +`-mshort-double' + Specify to use the 32-bit double ABI. + +`-mlong-double' + Specify to use the 64-bit double ABI. + +`--force-long-branches' + Relative branches are turned into absolute ones. This concerns + conditional branches, unconditional branches and branches to a sub + routine. + +`-S | --short-branches' + Do not turn relative branches into absolute ones when the offset + is out of range. + +`--strict-direct-mode' + Do not turn the direct addressing mode into extended addressing + mode when the instruction does not support direct addressing mode. + +`--print-insn-syntax' + Print the syntax of instruction in case of error. + +`--print-opcodes' + print the list of instructions with syntax and then exit. + +`--generate-example' + print an example of instruction for each possible instruction and + then exit. This option is only useful for testing `as'. + + + The following options are available when `as' is configured for the +SPARC architecture: + +`-Av6 | -Av7 | -Av8 | -Asparclet | -Asparclite' +`-Av8plus | -Av8plusa | -Av9 | -Av9a' + Explicitly select a variant of the SPARC architecture. + + `-Av8plus' and `-Av8plusa' select a 32 bit environment. `-Av9' + and `-Av9a' select a 64 bit environment. + + `-Av8plusa' and `-Av9a' enable the SPARC V9 instruction set with + UltraSPARC extensions. + +`-xarch=v8plus | -xarch=v8plusa' + For compatibility with the Solaris v9 assembler. These options are + equivalent to -Av8plus and -Av8plusa, respectively. + +`-bump' + Warn when the assembler switches to another architecture. + + The following options are available when as is configured for the +'c54x architecture. + +`-mfar-mode' + Enable extended addressing mode. All addresses and relocations + will assume extended addressing (usually 23 bits). + +`-mcpu=CPU_VERSION' + Sets the CPU version being compiled for. + +`-merrors-to-file FILENAME' + Redirect error output to a file, for broken systems which don't + support such behaviour in the shell. + + The following options are available when as is configured for a MIPS +processor. + +`-G NUM' + This option sets the largest size of an object that can be + referenced implicitly with the `gp' register. It is only accepted + for targets that use ECOFF format, such as a DECstation running + Ultrix. The default value is 8. + +`-EB' + Generate "big endian" format output. + +`-EL' + Generate "little endian" format output. + +`-mips1' +`-mips2' +`-mips3' +`-mips4' +`-mips5' +`-mips32' +`-mips32r2' +`-mips64' +`-mips64r2' + Generate code for a particular MIPS Instruction Set Architecture + level. `-mips1' is an alias for `-march=r3000', `-mips2' is an + alias for `-march=r6000', `-mips3' is an alias for `-march=r4000' + and `-mips4' is an alias for `-march=r8000'. `-mips5', `-mips32', + `-mips32r2', `-mips64', and `-mips64r2' correspond to generic + `MIPS V', `MIPS32', `MIPS32 Release 2', `MIPS64', and `MIPS64 + Release 2' ISA processors, respectively. + +`-march=CPU' + Generate code for a particular MIPS cpu. + +`-mtune=CPU' + Schedule and tune for a particular MIPS cpu. + +`-mfix7000' +`-mno-fix7000' + Cause nops to be inserted if the read of the destination register + of an mfhi or mflo instruction occurs in the following two + instructions. + +`-mdebug' +`-no-mdebug' + Cause stabs-style debugging output to go into an ECOFF-style + .mdebug section instead of the standard ELF .stabs sections. + +`-mpdr' +`-mno-pdr' + Control generation of `.pdr' sections. + +`-mgp32' +`-mfp32' + The register sizes are normally inferred from the ISA and ABI, but + these flags force a certain group of registers to be treated as 32 + bits wide at all times. `-mgp32' controls the size of + general-purpose registers and `-mfp32' controls the size of + floating-point registers. + +`-mips16' +`-no-mips16' + Generate code for the MIPS 16 processor. This is equivalent to + putting `.set mips16' at the start of the assembly file. + `-no-mips16' turns off this option. + +`-msmartmips' +`-mno-smartmips' + Enables the SmartMIPS extension to the MIPS32 instruction set. + This is equivalent to putting `.set smartmips' at the start of the + assembly file. `-mno-smartmips' turns off this option. + +`-mips3d' +`-no-mips3d' + Generate code for the MIPS-3D Application Specific Extension. + This tells the assembler to accept MIPS-3D instructions. + `-no-mips3d' turns off this option. + +`-mdmx' +`-no-mdmx' + Generate code for the MDMX Application Specific Extension. This + tells the assembler to accept MDMX instructions. `-no-mdmx' turns + off this option. + +`-mdsp' +`-mno-dsp' + Generate code for the DSP Release 1 Application Specific Extension. + This tells the assembler to accept DSP Release 1 instructions. + `-mno-dsp' turns off this option. + +`-mdspr2' +`-mno-dspr2' + Generate code for the DSP Release 2 Application Specific Extension. + This option implies -mdsp. This tells the assembler to accept DSP + Release 2 instructions. `-mno-dspr2' turns off this option. + +`-mmt' +`-mno-mt' + Generate code for the MT Application Specific Extension. This + tells the assembler to accept MT instructions. `-mno-mt' turns + off this option. + +`--construct-floats' +`--no-construct-floats' + The `--no-construct-floats' option disables the construction of + double width floating point constants by loading the two halves of + the value into the two single width floating point registers that + make up the double width register. By default + `--construct-floats' is selected, allowing construction of these + floating point constants. + +`--emulation=NAME' + This option causes `as' to emulate `as' configured for some other + target, in all respects, including output format (choosing between + ELF and ECOFF only), handling of pseudo-opcodes which may generate + debugging information or store symbol table information, and + default endianness. The available configuration names are: + `mipsecoff', `mipself', `mipslecoff', `mipsbecoff', `mipslelf', + `mipsbelf'. The first two do not alter the default endianness + from that of the primary target for which the assembler was + configured; the others change the default to little- or big-endian + as indicated by the `b' or `l' in the name. Using `-EB' or `-EL' + will override the endianness selection in any case. + + This option is currently supported only when the primary target + `as' is configured for is a MIPS ELF or ECOFF target. + Furthermore, the primary target or others specified with + `--enable-targets=...' at configuration time must include support + for the other format, if both are to be available. For example, + the Irix 5 configuration includes support for both. + + Eventually, this option will support more configurations, with more + fine-grained control over the assembler's behavior, and will be + supported for more processors. + +`-nocpp' + `as' ignores this option. It is accepted for compatibility with + the native tools. + +`--trap' +`--no-trap' +`--break' +`--no-break' + Control how to deal with multiplication overflow and division by + zero. `--trap' or `--no-break' (which are synonyms) take a trap + exception (and only work for Instruction Set Architecture level 2 + and higher); `--break' or `--no-trap' (also synonyms, and the + default) take a break exception. + +`-n' + When this option is used, `as' will issue a warning every time it + generates a nop instruction from a macro. + + The following options are available when as is configured for an +MCore processor. + +`-jsri2bsr' +`-nojsri2bsr' + Enable or disable the JSRI to BSR transformation. By default this + is enabled. The command line option `-nojsri2bsr' can be used to + disable it. + +`-sifilter' +`-nosifilter' + Enable or disable the silicon filter behaviour. By default this + is disabled. The default can be overridden by the `-sifilter' + command line option. + +`-relax' + Alter jump instructions for long displacements. + +`-mcpu=[210|340]' + Select the cpu type on the target hardware. This controls which + instructions can be assembled. + +`-EB' + Assemble for a big endian target. + +`-EL' + Assemble for a little endian target. + + + See the info pages for documentation of the MMIX-specific options. + + The following options are available when as is configured for the +s390 processor family. + +`-m31' +`-m64' + Select the word size, either 31/32 bits or 64 bits. + +`-mesa' + +`-mzarch' + Select the architecture mode, either the Enterprise System + Architecture (esa) or the z/Architecture mode (zarch). + +`-march=PROCESSOR' + Specify which s390 processor variant is the target, `g6', `g6', + `z900', `z990', `z9-109', `z9-ec', or `z10'. + +`-mregnames' +`-mno-regnames' + Allow or disallow symbolic names for registers. + +`-mwarn-areg-zero' + Warn whenever the operand for a base or index register has been + specified but evaluates to zero. + + The following options are available when as is configured for an +Xtensa processor. + +`--text-section-literals | --no-text-section-literals' + With `--text-section-literals', literal pools are interspersed in + the text section. The default is `--no-text-section-literals', + which places literals in a separate section in the output file. + These options only affect literals referenced via PC-relative + `L32R' instructions; literals for absolute mode `L32R' + instructions are handled separately. + +`--absolute-literals | --no-absolute-literals' + Indicate to the assembler whether `L32R' instructions use absolute + or PC-relative addressing. The default is to assume absolute + addressing if the Xtensa processor includes the absolute `L32R' + addressing option. Otherwise, only the PC-relative `L32R' mode + can be used. + +`--target-align | --no-target-align' + Enable or disable automatic alignment to reduce branch penalties + at the expense of some code density. The default is + `--target-align'. + +`--longcalls | --no-longcalls' + Enable or disable transformation of call instructions to allow + calls across a greater range of addresses. The default is + `--no-longcalls'. + +`--transform | --no-transform' + Enable or disable all assembler transformations of Xtensa + instructions. The default is `--transform'; `--no-transform' + should be used only in the rare cases when the instructions must + be exactly as specified in the assembly source. + +`--rename-section OLDNAME=NEWNAME' + When generating output sections, rename the OLDNAME section to + NEWNAME. + + The following options are available when as is configured for a Z80 +family processor. +`-z80' + Assemble for Z80 processor. + +`-r800' + Assemble for R800 processor. + +`-ignore-undocumented-instructions' +`-Wnud' + Assemble undocumented Z80 instructions that also work on R800 + without warning. + +`-ignore-unportable-instructions' +`-Wnup' + Assemble all undocumented Z80 instructions without warning. + +`-warn-undocumented-instructions' +`-Wud' + Issue a warning for undocumented Z80 instructions that also work + on R800. + +`-warn-unportable-instructions' +`-Wup' + Issue a warning for undocumented Z80 instructions that do not work + on R800. + +`-forbid-undocumented-instructions' +`-Fud' + Treat all undocumented instructions as errors. + +`-forbid-unportable-instructions' +`-Fup' + Treat undocumented Z80 instructions that do not work on R800 as + errors. + +* Menu: + +* Manual:: Structure of this Manual +* GNU Assembler:: The GNU Assembler +* Object Formats:: Object File Formats +* Command Line:: Command Line +* Input Files:: Input Files +* Object:: Output (Object) File +* Errors:: Error and Warning Messages + + +File: as.info, Node: Manual, Next: GNU Assembler, Up: Overview + +1.1 Structure of this Manual +============================ + +This manual is intended to describe what you need to know to use GNU +`as'. We cover the syntax expected in source files, including notation +for symbols, constants, and expressions; the directives that `as' +understands; and of course how to invoke `as'. + + This manual also describes some of the machine-dependent features of +various flavors of the assembler. + + On the other hand, this manual is _not_ intended as an introduction +to programming in assembly language--let alone programming in general! +In a similar vein, we make no attempt to introduce the machine +architecture; we do _not_ describe the instruction set, standard +mnemonics, registers or addressing modes that are standard to a +particular architecture. You may want to consult the manufacturer's +machine architecture manual for this information. + + +File: as.info, Node: GNU Assembler, Next: Object Formats, Prev: Manual, Up: Overview + +1.2 The GNU Assembler +===================== + +GNU `as' is really a family of assemblers. If you use (or have used) +the GNU assembler on one architecture, you should find a fairly similar +environment when you use it on another architecture. Each version has +much in common with the others, including object file formats, most +assembler directives (often called "pseudo-ops") and assembler syntax. + + `as' is primarily intended to assemble the output of the GNU C +compiler `gcc' for use by the linker `ld'. Nevertheless, we've tried +to make `as' assemble correctly everything that other assemblers for +the same machine would assemble. Any exceptions are documented +explicitly (*note Machine Dependencies::). This doesn't mean `as' +always uses the same syntax as another assembler for the same +architecture; for example, we know of several incompatible versions of +680x0 assembly language syntax. + + Unlike older assemblers, `as' is designed to assemble a source +program in one pass of the source file. This has a subtle impact on the +`.org' directive (*note `.org': Org.). + + +File: as.info, Node: Object Formats, Next: Command Line, Prev: GNU Assembler, Up: Overview + +1.3 Object File Formats +======================= + +The GNU assembler can be configured to produce several alternative +object file formats. For the most part, this does not affect how you +write assembly language programs; but directives for debugging symbols +are typically different in different file formats. *Note Symbol +Attributes: Symbol Attributes. + + +File: as.info, Node: Command Line, Next: Input Files, Prev: Object Formats, Up: Overview + +1.4 Command Line +================ + +After the program name `as', the command line may contain options and +file names. Options may appear in any order, and may be before, after, +or between file names. The order of file names is significant. + + `--' (two hyphens) by itself names the standard input file +explicitly, as one of the files for `as' to assemble. + + Except for `--' any command line argument that begins with a hyphen +(`-') is an option. Each option changes the behavior of `as'. No +option changes the way another option works. An option is a `-' +followed by one or more letters; the case of the letter is important. +All options are optional. + + Some options expect exactly one file name to follow them. The file +name may either immediately follow the option's letter (compatible with +older assemblers) or it may be the next command argument (GNU +standard). These two command lines are equivalent: + + as -o my-object-file.o mumble.s + as -omy-object-file.o mumble.s + + +File: as.info, Node: Input Files, Next: Object, Prev: Command Line, Up: Overview + +1.5 Input Files +=============== + +We use the phrase "source program", abbreviated "source", to describe +the program input to one run of `as'. The program may be in one or +more files; how the source is partitioned into files doesn't change the +meaning of the source. + + The source program is a concatenation of the text in all the files, +in the order specified. + + Each time you run `as' it assembles exactly one source program. The +source program is made up of one or more files. (The standard input is +also a file.) + + You give `as' a command line that has zero or more input file names. +The input files are read (from left file name to right). A command +line argument (in any position) that has no special meaning is taken to +be an input file name. + + If you give `as' no file names it attempts to read one input file +from the `as' standard input, which is normally your terminal. You may +have to type <ctl-D> to tell `as' there is no more program to assemble. + + Use `--' if you need to explicitly name the standard input file in +your command line. + + If the source is empty, `as' produces a small, empty object file. + +Filenames and Line-numbers +-------------------------- + +There are two ways of locating a line in the input file (or files) and +either may be used in reporting error messages. One way refers to a +line number in a physical file; the other refers to a line number in a +"logical" file. *Note Error and Warning Messages: Errors. + + "Physical files" are those files named in the command line given to +`as'. + + "Logical files" are simply names declared explicitly by assembler +directives; they bear no relation to physical files. Logical file +names help error messages reflect the original source file, when `as' +source is itself synthesized from other files. `as' understands the +`#' directives emitted by the `gcc' preprocessor. See also *Note +`.file': File. + + +File: as.info, Node: Object, Next: Errors, Prev: Input Files, Up: Overview + +1.6 Output (Object) File +======================== + +Every time you run `as' it produces an output file, which is your +assembly language program translated into numbers. This file is the +object file. Its default name is `a.out'. You can give it another +name by using the `-o' option. Conventionally, object file names end +with `.o'. The default name is used for historical reasons: older +assemblers were capable of assembling self-contained programs directly +into a runnable program. (For some formats, this isn't currently +possible, but it can be done for the `a.out' format.) + + The object file is meant for input to the linker `ld'. It contains +assembled program code, information to help `ld' integrate the +assembled program into a runnable file, and (optionally) symbolic +information for the debugger. + + +File: as.info, Node: Errors, Prev: Object, Up: Overview + +1.7 Error and Warning Messages +============================== + +`as' may write warnings and error messages to the standard error file +(usually your terminal). This should not happen when a compiler runs +`as' automatically. Warnings report an assumption made so that `as' +could keep assembling a flawed program; errors report a grave problem +that stops the assembly. + + Warning messages have the format + + file_name:NNN:Warning Message Text + +(where NNN is a line number). If a logical file name has been given +(*note `.file': File.) it is used for the filename, otherwise the name +of the current input file is used. If a logical line number was given +(*note `.line': Line.) then it is used to calculate the number printed, +otherwise the actual line in the current source file is printed. The +message text is intended to be self explanatory (in the grand Unix +tradition). + + Error messages have the format + file_name:NNN:FATAL:Error Message Text + The file name and line number are derived as for warning messages. +The actual message text may be rather less explanatory because many of +them aren't supposed to happen. + + +File: as.info, Node: Invoking, Next: Syntax, Prev: Overview, Up: Top + +2 Command-Line Options +********************** + +This chapter describes command-line options available in _all_ versions +of the GNU assembler; see *Note Machine Dependencies::, for options +specific to particular machine architectures. + + If you are invoking `as' via the GNU C compiler, you can use the +`-Wa' option to pass arguments through to the assembler. The assembler +arguments must be separated from each other (and the `-Wa') by commas. +For example: + + gcc -c -g -O -Wa,-alh,-L file.c + +This passes two options to the assembler: `-alh' (emit a listing to +standard output with high-level and assembly source) and `-L' (retain +local symbols in the symbol table). + + Usually you do not need to use this `-Wa' mechanism, since many +compiler command-line options are automatically passed to the assembler +by the compiler. (You can call the GNU compiler driver with the `-v' +option to see precisely what options it passes to each compilation +pass, including the assembler.) + +* Menu: + +* a:: -a[cdghlns] enable listings +* alternate:: --alternate enable alternate macro syntax +* D:: -D for compatibility +* f:: -f to work faster +* I:: -I for .include search path + +* K:: -K for difference tables + +* L:: -L to retain local symbols +* listing:: --listing-XXX to configure listing output +* M:: -M or --mri to assemble in MRI compatibility mode +* MD:: --MD for dependency tracking +* o:: -o to name the object file +* R:: -R to join data and text sections +* statistics:: --statistics to see statistics about assembly +* traditional-format:: --traditional-format for compatible output +* v:: -v to announce version +* W:: -W, --no-warn, --warn, --fatal-warnings to control warnings +* Z:: -Z to make object file even after errors + + +File: as.info, Node: a, Next: alternate, Up: Invoking + +2.1 Enable Listings: `-a[cdghlns]' +================================== + +These options enable listing output from the assembler. By itself, +`-a' requests high-level, assembly, and symbols listing. You can use +other letters to select specific options for the list: `-ah' requests a +high-level language listing, `-al' requests an output-program assembly +listing, and `-as' requests a symbol table listing. High-level +listings require that a compiler debugging option like `-g' be used, +and that assembly listings (`-al') be requested also. + + Use the `-ag' option to print a first section with general assembly +information, like as version, switches passed, or time stamp. + + Use the `-ac' option to omit false conditionals from a listing. Any +lines which are not assembled because of a false `.if' (or `.ifdef', or +any other conditional), or a true `.if' followed by an `.else', will be +omitted from the listing. + + Use the `-ad' option to omit debugging directives from the listing. + + Once you have specified one of these options, you can further control +listing output and its appearance using the directives `.list', +`.nolist', `.psize', `.eject', `.title', and `.sbttl'. The `-an' +option turns off all forms processing. If you do not request listing +output with one of the `-a' options, the listing-control directives +have no effect. + + The letters after `-a' may be combined into one option, _e.g._, +`-aln'. + + Note if the assembler source is coming from the standard input (e.g., +because it is being created by `gcc' and the `-pipe' command line switch +is being used) then the listing will not contain any comments or +preprocessor directives. This is because the listing code buffers +input source lines from stdin only after they have been preprocessed by +the assembler. This reduces memory usage and makes the code more +efficient. + + +File: as.info, Node: alternate, Next: D, Prev: a, Up: Invoking + +2.2 `--alternate' +================= + +Begin in alternate macro mode, see *Note `.altmacro': Altmacro. + + +File: as.info, Node: D, Next: f, Prev: alternate, Up: Invoking + +2.3 `-D' +======== + +This option has no effect whatsoever, but it is accepted to make it more +likely that scripts written for other assemblers also work with `as'. + + +File: as.info, Node: f, Next: I, Prev: D, Up: Invoking + +2.4 Work Faster: `-f' +===================== + +`-f' should only be used when assembling programs written by a +(trusted) compiler. `-f' stops the assembler from doing whitespace and +comment preprocessing on the input file(s) before assembling them. +*Note Preprocessing: Preprocessing. + + _Warning:_ if you use `-f' when the files actually need to be + preprocessed (if they contain comments, for example), `as' does + not work correctly. + + +File: as.info, Node: I, Next: K, Prev: f, Up: Invoking + +2.5 `.include' Search Path: `-I' PATH +===================================== + +Use this option to add a PATH to the list of directories `as' searches +for files specified in `.include' directives (*note `.include': +Include.). You may use `-I' as many times as necessary to include a +variety of paths. The current working directory is always searched +first; after that, `as' searches any `-I' directories in the same order +as they were specified (left to right) on the command line. + + +File: as.info, Node: K, Next: L, Prev: I, Up: Invoking + +2.6 Difference Tables: `-K' +=========================== + +`as' sometimes alters the code emitted for directives of the form +`.word SYM1-SYM2'. *Note `.word': Word. You can use the `-K' option +if you want a warning issued when this is done. + + +File: as.info, Node: L, Next: listing, Prev: K, Up: Invoking + +2.7 Include Local Symbols: `-L' +=============================== + +Symbols beginning with system-specific local label prefixes, typically +`.L' for ELF systems or `L' for traditional a.out systems, are called +"local symbols". *Note Symbol Names::. Normally you do not see such +symbols when debugging, because they are intended for the use of +programs (like compilers) that compose assembler programs, not for your +notice. Normally both `as' and `ld' discard such symbols, so you do +not normally debug with them. + + This option tells `as' to retain those local symbols in the object +file. Usually if you do this you also tell the linker `ld' to preserve +those symbols. + + +File: as.info, Node: listing, Next: M, Prev: L, Up: Invoking + +2.8 Configuring listing output: `--listing' +=========================================== + +The listing feature of the assembler can be enabled via the command +line switch `-a' (*note a::). This feature combines the input source +file(s) with a hex dump of the corresponding locations in the output +object file, and displays them as a listing file. The format of this +listing can be controlled by directives inside the assembler source +(i.e., `.list' (*note List::), `.title' (*note Title::), `.sbttl' +(*note Sbttl::), `.psize' (*note Psize::), and `.eject' (*note Eject::) +and also by the following switches: + +`--listing-lhs-width=`number'' + Sets the maximum width, in words, of the first line of the hex + byte dump. This dump appears on the left hand side of the listing + output. + +`--listing-lhs-width2=`number'' + Sets the maximum width, in words, of any further lines of the hex + byte dump for a given input source line. If this value is not + specified, it defaults to being the same as the value specified + for `--listing-lhs-width'. If neither switch is used the default + is to one. + +`--listing-rhs-width=`number'' + Sets the maximum width, in characters, of the source line that is + displayed alongside the hex dump. The default value for this + parameter is 100. The source line is displayed on the right hand + side of the listing output. + +`--listing-cont-lines=`number'' + Sets the maximum number of continuation lines of hex dump that + will be displayed for a given single line of source input. The + default value is 4. + + +File: as.info, Node: M, Next: MD, Prev: listing, Up: Invoking + +2.9 Assemble in MRI Compatibility Mode: `-M' +============================================ + +The `-M' or `--mri' option selects MRI compatibility mode. This +changes the syntax and pseudo-op handling of `as' to make it compatible +with the `ASM68K' or the `ASM960' (depending upon the configured +target) assembler from Microtec Research. The exact nature of the MRI +syntax will not be documented here; see the MRI manuals for more +information. Note in particular that the handling of macros and macro +arguments is somewhat different. The purpose of this option is to +permit assembling existing MRI assembler code using `as'. + + The MRI compatibility is not complete. Certain operations of the +MRI assembler depend upon its object file format, and can not be +supported using other object file formats. Supporting these would +require enhancing each object file format individually. These are: + + * global symbols in common section + + The m68k MRI assembler supports common sections which are merged + by the linker. Other object file formats do not support this. + `as' handles common sections by treating them as a single common + symbol. It permits local symbols to be defined within a common + section, but it can not support global symbols, since it has no + way to describe them. + + * complex relocations + + The MRI assemblers support relocations against a negated section + address, and relocations which combine the start addresses of two + or more sections. These are not support by other object file + formats. + + * `END' pseudo-op specifying start address + + The MRI `END' pseudo-op permits the specification of a start + address. This is not supported by other object file formats. The + start address may instead be specified using the `-e' option to + the linker, or in a linker script. + + * `IDNT', `.ident' and `NAME' pseudo-ops + + The MRI `IDNT', `.ident' and `NAME' pseudo-ops assign a module + name to the output file. This is not supported by other object + file formats. + + * `ORG' pseudo-op + + The m68k MRI `ORG' pseudo-op begins an absolute section at a given + address. This differs from the usual `as' `.org' pseudo-op, which + changes the location within the current section. Absolute + sections are not supported by other object file formats. The + address of a section may be assigned within a linker script. + + There are some other features of the MRI assembler which are not +supported by `as', typically either because they are difficult or +because they seem of little consequence. Some of these may be +supported in future releases. + + * EBCDIC strings + + EBCDIC strings are not supported. + + * packed binary coded decimal + + Packed binary coded decimal is not supported. This means that the + `DC.P' and `DCB.P' pseudo-ops are not supported. + + * `FEQU' pseudo-op + + The m68k `FEQU' pseudo-op is not supported. + + * `NOOBJ' pseudo-op + + The m68k `NOOBJ' pseudo-op is not supported. + + * `OPT' branch control options + + The m68k `OPT' branch control options--`B', `BRS', `BRB', `BRL', + and `BRW'--are ignored. `as' automatically relaxes all branches, + whether forward or backward, to an appropriate size, so these + options serve no purpose. + + * `OPT' list control options + + The following m68k `OPT' list control options are ignored: `C', + `CEX', `CL', `CRE', `E', `G', `I', `M', `MEX', `MC', `MD', `X'. + + * other `OPT' options + + The following m68k `OPT' options are ignored: `NEST', `O', `OLD', + `OP', `P', `PCO', `PCR', `PCS', `R'. + + * `OPT' `D' option is default + + The m68k `OPT' `D' option is the default, unlike the MRI assembler. + `OPT NOD' may be used to turn it off. + + * `XREF' pseudo-op. + + The m68k `XREF' pseudo-op is ignored. + + * `.debug' pseudo-op + + The i960 `.debug' pseudo-op is not supported. + + * `.extended' pseudo-op + + The i960 `.extended' pseudo-op is not supported. + + * `.list' pseudo-op. + + The various options of the i960 `.list' pseudo-op are not + supported. + + * `.optimize' pseudo-op + + The i960 `.optimize' pseudo-op is not supported. + + * `.output' pseudo-op + + The i960 `.output' pseudo-op is not supported. + + * `.setreal' pseudo-op + + The i960 `.setreal' pseudo-op is not supported. + + + +File: as.info, Node: MD, Next: o, Prev: M, Up: Invoking + +2.10 Dependency Tracking: `--MD' +================================ + +`as' can generate a dependency file for the file it creates. This file +consists of a single rule suitable for `make' describing the +dependencies of the main source file. + + The rule is written to the file named in its argument. + + This feature is used in the automatic updating of makefiles. + + +File: as.info, Node: o, Next: R, Prev: MD, Up: Invoking + +2.11 Name the Object File: `-o' +=============================== + +There is always one object file output when you run `as'. By default +it has the name `a.out' (or `b.out', for Intel 960 targets only). You +use this option (which takes exactly one filename) to give the object +file a different name. + + Whatever the object file is called, `as' overwrites any existing +file of the same name. + + +File: as.info, Node: R, Next: statistics, Prev: o, Up: Invoking + +2.12 Join Data and Text Sections: `-R' +====================================== + +`-R' tells `as' to write the object file as if all data-section data +lives in the text section. This is only done at the very last moment: +your binary data are the same, but data section parts are relocated +differently. The data section part of your object file is zero bytes +long because all its bytes are appended to the text section. (*Note +Sections and Relocation: Sections.) + + When you specify `-R' it would be possible to generate shorter +address displacements (because we do not have to cross between text and +data section). We refrain from doing this simply for compatibility with +older versions of `as'. In future, `-R' may work this way. + + When `as' is configured for COFF or ELF output, this option is only +useful if you use sections named `.text' and `.data'. + + `-R' is not supported for any of the HPPA targets. Using `-R' +generates a warning from `as'. + + +File: as.info, Node: statistics, Next: traditional-format, Prev: R, Up: Invoking + +2.13 Display Assembly Statistics: `--statistics' +================================================ + +Use `--statistics' to display two statistics about the resources used by +`as': the maximum amount of space allocated during the assembly (in +bytes), and the total execution time taken for the assembly (in CPU +seconds). + + +File: as.info, Node: traditional-format, Next: v, Prev: statistics, Up: Invoking + +2.14 Compatible Output: `--traditional-format' +============================================== + +For some targets, the output of `as' is different in some ways from the +output of some existing assembler. This switch requests `as' to use +the traditional format instead. + + For example, it disables the exception frame optimizations which +`as' normally does by default on `gcc' output. + + +File: as.info, Node: v, Next: W, Prev: traditional-format, Up: Invoking + +2.15 Announce Version: `-v' +=========================== + +You can find out what version of as is running by including the option +`-v' (which you can also spell as `-version') on the command line. + + +File: as.info, Node: W, Next: Z, Prev: v, Up: Invoking + +2.16 Control Warnings: `-W', `--warn', `--no-warn', `--fatal-warnings' +====================================================================== + +`as' should never give a warning or error message when assembling +compiler output. But programs written by people often cause `as' to +give a warning that a particular assumption was made. All such +warnings are directed to the standard error file. + + If you use the `-W' and `--no-warn' options, no warnings are issued. +This only affects the warning messages: it does not change any +particular of how `as' assembles your file. Errors, which stop the +assembly, are still reported. + + If you use the `--fatal-warnings' option, `as' considers files that +generate warnings to be in error. + + You can switch these options off again by specifying `--warn', which +causes warnings to be output as usual. + + +File: as.info, Node: Z, Prev: W, Up: Invoking + +2.17 Generate Object File in Spite of Errors: `-Z' +================================================== + +After an error message, `as' normally produces no output. If for some +reason you are interested in object file output even after `as' gives +an error message on your program, use the `-Z' option. If there are +any errors, `as' continues anyways, and writes an object file after a +final warning message of the form `N errors, M warnings, generating bad +object file.' + + +File: as.info, Node: Syntax, Next: Sections, Prev: Invoking, Up: Top + +3 Syntax +******** + +This chapter describes the machine-independent syntax allowed in a +source file. `as' syntax is similar to what many other assemblers use; +it is inspired by the BSD 4.2 assembler, except that `as' does not +assemble Vax bit-fields. + +* Menu: + +* Preprocessing:: Preprocessing +* Whitespace:: Whitespace +* Comments:: Comments +* Symbol Intro:: Symbols +* Statements:: Statements +* Constants:: Constants + + +File: as.info, Node: Preprocessing, Next: Whitespace, Up: Syntax + +3.1 Preprocessing +================= + +The `as' internal preprocessor: + * adjusts and removes extra whitespace. It leaves one space or tab + before the keywords on a line, and turns any other whitespace on + the line into a single space. + + * removes all comments, replacing them with a single space, or an + appropriate number of newlines. + + * converts character constants into the appropriate numeric values. + + It does not do macro processing, include file handling, or anything +else you may get from your C compiler's preprocessor. You can do +include file processing with the `.include' directive (*note +`.include': Include.). You can use the GNU C compiler driver to get +other "CPP" style preprocessing by giving the input file a `.S' suffix. +*Note Options Controlling the Kind of Output: (gcc.info)Overall +Options. + + Excess whitespace, comments, and character constants cannot be used +in the portions of the input text that are not preprocessed. + + If the first line of an input file is `#NO_APP' or if you use the +`-f' option, whitespace and comments are not removed from the input +file. Within an input file, you can ask for whitespace and comment +removal in specific portions of the by putting a line that says `#APP' +before the text that may contain whitespace or comments, and putting a +line that says `#NO_APP' after this text. This feature is mainly +intend to support `asm' statements in compilers whose output is +otherwise free of comments and whitespace. + + +File: as.info, Node: Whitespace, Next: Comments, Prev: Preprocessing, Up: Syntax + +3.2 Whitespace +============== + +"Whitespace" is one or more blanks or tabs, in any order. Whitespace +is used to separate symbols, and to make programs neater for people to +read. Unless within character constants (*note Character Constants: +Characters.), any whitespace means the same as exactly one space. + + +File: as.info, Node: Comments, Next: Symbol Intro, Prev: Whitespace, Up: Syntax + +3.3 Comments +============ + +There are two ways of rendering comments to `as'. In both cases the +comment is equivalent to one space. + + Anything from `/*' through the next `*/' is a comment. This means +you may not nest these comments. + + /* + The only way to include a newline ('\n') in a comment + is to use this sort of comment. + */ + + /* This sort of comment does not nest. */ + + Anything from the "line comment" character to the next newline is +considered a comment and is ignored. The line comment character is `;' +on the ARC; `@' on the ARM; `;' for the H8/300 family; `;' for the HPPA; +`#' on the i386 and x86-64; `#' on the i960; `;' for the PDP-11; `;' +for picoJava; `#' for Motorola PowerPC; `#' for IBM S/390; `#' for the +Sunplus SCORE; `!' for the Renesas / SuperH SH; `!' on the SPARC; `#' +on the ip2k; `#' on the m32c; `#' on the m32r; `|' on the 680x0; `#' on +the 68HC11 and 68HC12; `#' on the Vax; `;' for the Z80; `!' for the +Z8000; `#' on the V850; `#' for Xtensa systems; see *Note Machine +Dependencies::. + + On some machines there are two different line comment characters. +One character only begins a comment if it is the first non-whitespace +character on a line, while the other always begins a comment. + + The V850 assembler also supports a double dash as starting a comment +that extends to the end of the line. + + `--'; + + To be compatible with past assemblers, lines that begin with `#' +have a special interpretation. Following the `#' should be an absolute +expression (*note Expressions::): the logical line number of the _next_ +line. Then a string (*note Strings: Strings.) is allowed: if present +it is a new logical file name. The rest of the line, if any, should be +whitespace. + + If the first non-whitespace characters on the line are not numeric, +the line is ignored. (Just like a comment.) + + # This is an ordinary comment. + # 42-6 "new_file_name" # New logical file name + # This is logical line # 36. + This feature is deprecated, and may disappear from future versions +of `as'. + + +File: as.info, Node: Symbol Intro, Next: Statements, Prev: Comments, Up: Syntax + +3.4 Symbols +=========== + +A "symbol" is one or more characters chosen from the set of all letters +(both upper and lower case), digits and the three characters `_.$'. On +most machines, you can also use `$' in symbol names; exceptions are +noted in *Note Machine Dependencies::. No symbol may begin with a +digit. Case is significant. There is no length limit: all characters +are significant. Symbols are delimited by characters not in that set, +or by the beginning of a file (since the source program must end with a +newline, the end of a file is not a possible symbol delimiter). *Note +Symbols::. + + +File: as.info, Node: Statements, Next: Constants, Prev: Symbol Intro, Up: Syntax + +3.5 Statements +============== + +A "statement" ends at a newline character (`\n') or line separator +character. (The line separator is usually `;', unless this conflicts +with the comment character; see *Note Machine Dependencies::.) The +newline or separator character is considered part of the preceding +statement. Newlines and separators within character constants are an +exception: they do not end statements. + +It is an error to end any statement with end-of-file: the last +character of any input file should be a newline. + + An empty statement is allowed, and may include whitespace. It is +ignored. + + A statement begins with zero or more labels, optionally followed by a +key symbol which determines what kind of statement it is. The key +symbol determines the syntax of the rest of the statement. If the +symbol begins with a dot `.' then the statement is an assembler +directive: typically valid for any computer. If the symbol begins with +a letter the statement is an assembly language "instruction": it +assembles into a machine language instruction. Different versions of +`as' for different computers recognize different instructions. In +fact, the same symbol may represent a different instruction in a +different computer's assembly language. + + A label is a symbol immediately followed by a colon (`:'). +Whitespace before a label or after a colon is permitted, but you may not +have whitespace between a label's symbol and its colon. *Note Labels::. + + For HPPA targets, labels need not be immediately followed by a +colon, but the definition of a label must begin in column zero. This +also implies that only one label may be defined on each line. + + label: .directive followed by something + another_label: # This is an empty statement. + instruction operand_1, operand_2, ... + + +File: as.info, Node: Constants, Prev: Statements, Up: Syntax + +3.6 Constants +============= + +A constant is a number, written so that its value is known by +inspection, without knowing any context. Like this: + .byte 74, 0112, 092, 0x4A, 0X4a, 'J, '\J # All the same value. + .ascii "Ring the bell\7" # A string constant. + .octa 0x123456789abcdef0123456789ABCDEF0 # A bignum. + .float 0f-314159265358979323846264338327\ + 95028841971.693993751E-40 # - pi, a flonum. + +* Menu: + +* Characters:: Character Constants +* Numbers:: Number Constants + + +File: as.info, Node: Characters, Next: Numbers, Up: Constants + +3.6.1 Character Constants +------------------------- + +There are two kinds of character constants. A "character" stands for +one character in one byte and its value may be used in numeric +expressions. String constants (properly called string _literals_) are +potentially many bytes and their values may not be used in arithmetic +expressions. + +* Menu: + +* Strings:: Strings +* Chars:: Characters + + +File: as.info, Node: Strings, Next: Chars, Up: Characters + +3.6.1.1 Strings +............... + +A "string" is written between double-quotes. It may contain +double-quotes or null characters. The way to get special characters +into a string is to "escape" these characters: precede them with a +backslash `\' character. For example `\\' represents one backslash: +the first `\' is an escape which tells `as' to interpret the second +character literally as a backslash (which prevents `as' from +recognizing the second `\' as an escape character). The complete list +of escapes follows. + +`\b' + Mnemonic for backspace; for ASCII this is octal code 010. + +`\f' + Mnemonic for FormFeed; for ASCII this is octal code 014. + +`\n' + Mnemonic for newline; for ASCII this is octal code 012. + +`\r' + Mnemonic for carriage-Return; for ASCII this is octal code 015. + +`\t' + Mnemonic for horizontal Tab; for ASCII this is octal code 011. + +`\ DIGIT DIGIT DIGIT' + An octal character code. The numeric code is 3 octal digits. For + compatibility with other Unix systems, 8 and 9 are accepted as + digits: for example, `\008' has the value 010, and `\009' the + value 011. + +`\`x' HEX-DIGITS...' + A hex character code. All trailing hex digits are combined. + Either upper or lower case `x' works. + +`\\' + Represents one `\' character. + +`\"' + Represents one `"' character. Needed in strings to represent this + character, because an unescaped `"' would end the string. + +`\ ANYTHING-ELSE' + Any other character when escaped by `\' gives a warning, but + assembles as if the `\' was not present. The idea is that if you + used an escape sequence you clearly didn't want the literal + interpretation of the following character. However `as' has no + other interpretation, so `as' knows it is giving you the wrong + code and warns you of the fact. + + Which characters are escapable, and what those escapes represent, +varies widely among assemblers. The current set is what we think the +BSD 4.2 assembler recognizes, and is a subset of what most C compilers +recognize. If you are in doubt, do not use an escape sequence. + + +File: as.info, Node: Chars, Prev: Strings, Up: Characters + +3.6.1.2 Characters +.................. + +A single character may be written as a single quote immediately +followed by that character. The same escapes apply to characters as to +strings. So if you want to write the character backslash, you must +write `'\\' where the first `\' escapes the second `\'. As you can +see, the quote is an acute accent, not a grave accent. A newline +immediately following an acute accent is taken as a literal character +and does not count as the end of a statement. The value of a character +constant in a numeric expression is the machine's byte-wide code for +that character. `as' assumes your character code is ASCII: `'A' means +65, `'B' means 66, and so on. + + +File: as.info, Node: Numbers, Prev: Characters, Up: Constants + +3.6.2 Number Constants +---------------------- + +`as' distinguishes three kinds of numbers according to how they are +stored in the target machine. _Integers_ are numbers that would fit +into an `int' in the C language. _Bignums_ are integers, but they are +stored in more than 32 bits. _Flonums_ are floating point numbers, +described below. + +* Menu: + +* Integers:: Integers +* Bignums:: Bignums +* Flonums:: Flonums + + +File: as.info, Node: Integers, Next: Bignums, Up: Numbers + +3.6.2.1 Integers +................ + +A binary integer is `0b' or `0B' followed by zero or more of the binary +digits `01'. + + An octal integer is `0' followed by zero or more of the octal digits +(`01234567'). + + A decimal integer starts with a non-zero digit followed by zero or +more digits (`0123456789'). + + A hexadecimal integer is `0x' or `0X' followed by one or more +hexadecimal digits chosen from `0123456789abcdefABCDEF'. + + Integers have the usual values. To denote a negative integer, use +the prefix operator `-' discussed under expressions (*note Prefix +Operators: Prefix Ops.). + + +File: as.info, Node: Bignums, Next: Flonums, Prev: Integers, Up: Numbers + +3.6.2.2 Bignums +............... + +A "bignum" has the same syntax and semantics as an integer except that +the number (or its negative) takes more than 32 bits to represent in +binary. The distinction is made because in some places integers are +permitted while bignums are not. + + +File: as.info, Node: Flonums, Prev: Bignums, Up: Numbers + +3.6.2.3 Flonums +............... + +A "flonum" represents a floating point number. The translation is +indirect: a decimal floating point number from the text is converted by +`as' to a generic binary floating point number of more than sufficient +precision. This generic floating point number is converted to a +particular computer's floating point format (or formats) by a portion +of `as' specialized to that computer. + + A flonum is written by writing (in order) + * The digit `0'. (`0' is optional on the HPPA.) + + * A letter, to tell `as' the rest of the number is a flonum. `e' is + recommended. Case is not important. + + On the H8/300, Renesas / SuperH SH, and AMD 29K architectures, the + letter must be one of the letters `DFPRSX' (in upper or lower + case). + + On the ARC, the letter must be one of the letters `DFRS' (in upper + or lower case). + + On the Intel 960 architecture, the letter must be one of the + letters `DFT' (in upper or lower case). + + On the HPPA architecture, the letter must be `E' (upper case only). + + * An optional sign: either `+' or `-'. + + * An optional "integer part": zero or more decimal digits. + + * An optional "fractional part": `.' followed by zero or more + decimal digits. + + * An optional exponent, consisting of: + + * An `E' or `e'. + + * Optional sign: either `+' or `-'. + + * One or more decimal digits. + + + At least one of the integer part or the fractional part must be +present. The floating point number has the usual base-10 value. + + `as' does all processing using integers. Flonums are computed +independently of any floating point hardware in the computer running +`as'. + + +File: as.info, Node: Sections, Next: Symbols, Prev: Syntax, Up: Top + +4 Sections and Relocation +************************* + +* Menu: + +* Secs Background:: Background +* Ld Sections:: Linker Sections +* As Sections:: Assembler Internal Sections +* Sub-Sections:: Sub-Sections +* bss:: bss Section + + +File: as.info, Node: Secs Background, Next: Ld Sections, Up: Sections + +4.1 Background +============== + +Roughly, a section is a range of addresses, with no gaps; all data "in" +those addresses is treated the same for some particular purpose. For +example there may be a "read only" section. + + The linker `ld' reads many object files (partial programs) and +combines their contents to form a runnable program. When `as' emits an +object file, the partial program is assumed to start at address 0. +`ld' assigns the final addresses for the partial program, so that +different partial programs do not overlap. This is actually an +oversimplification, but it suffices to explain how `as' uses sections. + + `ld' moves blocks of bytes of your program to their run-time +addresses. These blocks slide to their run-time addresses as rigid +units; their length does not change and neither does the order of bytes +within them. Such a rigid unit is called a _section_. Assigning +run-time addresses to sections is called "relocation". It includes the +task of adjusting mentions of object-file addresses so they refer to +the proper run-time addresses. For the H8/300, and for the Renesas / +SuperH SH, `as' pads sections if needed to ensure they end on a word +(sixteen bit) boundary. + + An object file written by `as' has at least three sections, any of +which may be empty. These are named "text", "data" and "bss" sections. + + When it generates COFF or ELF output, `as' can also generate +whatever other named sections you specify using the `.section' +directive (*note `.section': Section.). If you do not use any +directives that place output in the `.text' or `.data' sections, these +sections still exist, but are empty. + + When `as' generates SOM or ELF output for the HPPA, `as' can also +generate whatever other named sections you specify using the `.space' +and `.subspace' directives. See `HP9000 Series 800 Assembly Language +Reference Manual' (HP 92432-90001) for details on the `.space' and +`.subspace' assembler directives. + + Additionally, `as' uses different names for the standard text, data, +and bss sections when generating SOM output. Program text is placed +into the `$CODE$' section, data into `$DATA$', and BSS into `$BSS$'. + + Within the object file, the text section starts at address `0', the +data section follows, and the bss section follows the data section. + + When generating either SOM or ELF output files on the HPPA, the text +section starts at address `0', the data section at address `0x4000000', +and the bss section follows the data section. + + To let `ld' know which data changes when the sections are relocated, +and how to change that data, `as' also writes to the object file +details of the relocation needed. To perform relocation `ld' must +know, each time an address in the object file is mentioned: + * Where in the object file is the beginning of this reference to an + address? + + * How long (in bytes) is this reference? + + * Which section does the address refer to? What is the numeric + value of + (ADDRESS) - (START-ADDRESS OF SECTION)? + + * Is the reference to an address "Program-Counter relative"? + + In fact, every address `as' ever uses is expressed as + (SECTION) + (OFFSET INTO SECTION) + Further, most expressions `as' computes have this section-relative +nature. (For some object formats, such as SOM for the HPPA, some +expressions are symbol-relative instead.) + + In this manual we use the notation {SECNAME N} to mean "offset N +into section SECNAME." + + Apart from text, data and bss sections you need to know about the +"absolute" section. When `ld' mixes partial programs, addresses in the +absolute section remain unchanged. For example, address `{absolute 0}' +is "relocated" to run-time address 0 by `ld'. Although the linker +never arranges two partial programs' data sections with overlapping +addresses after linking, _by definition_ their absolute sections must +overlap. Address `{absolute 239}' in one part of a program is always +the same address when the program is running as address `{absolute +239}' in any other part of the program. + + The idea of sections is extended to the "undefined" section. Any +address whose section is unknown at assembly time is by definition +rendered {undefined U}--where U is filled in later. Since numbers are +always defined, the only way to generate an undefined address is to +mention an undefined symbol. A reference to a named common block would +be such a symbol: its value is unknown at assembly time so it has +section _undefined_. + + By analogy the word _section_ is used to describe groups of sections +in the linked program. `ld' puts all partial programs' text sections +in contiguous addresses in the linked program. It is customary to +refer to the _text section_ of a program, meaning all the addresses of +all partial programs' text sections. Likewise for data and bss +sections. + + Some sections are manipulated by `ld'; others are invented for use +of `as' and have no meaning except during assembly. + + +File: as.info, Node: Ld Sections, Next: As Sections, Prev: Secs Background, Up: Sections + +4.2 Linker Sections +=================== + +`ld' deals with just four kinds of sections, summarized below. + +*named sections* +*text section* +*data section* + These sections hold your program. `as' and `ld' treat them as + separate but equal sections. Anything you can say of one section + is true of another. When the program is running, however, it is + customary for the text section to be unalterable. The text + section is often shared among processes: it contains instructions, + constants and the like. The data section of a running program is + usually alterable: for example, C variables would be stored in the + data section. + +*bss section* + This section contains zeroed bytes when your program begins + running. It is used to hold uninitialized variables or common + storage. The length of each partial program's bss section is + important, but because it starts out containing zeroed bytes there + is no need to store explicit zero bytes in the object file. The + bss section was invented to eliminate those explicit zeros from + object files. + +*absolute section* + Address 0 of this section is always "relocated" to runtime address + 0. This is useful if you want to refer to an address that `ld' + must not change when relocating. In this sense we speak of + absolute addresses being "unrelocatable": they do not change + during relocation. + +*undefined section* + This "section" is a catch-all for address references to objects + not in the preceding sections. + + An idealized example of three relocatable sections follows. The +example uses the traditional section names `.text' and `.data'. Memory +addresses are on the horizontal axis. + + +-----+----+--+ + partial program # 1: |ttttt|dddd|00| + +-----+----+--+ + + text data bss + seg. seg. seg. + + +---+---+---+ + partial program # 2: |TTT|DDD|000| + +---+---+---+ + + +--+---+-----+--+----+---+-----+~~ + linked program: | |TTT|ttttt| |dddd|DDD|00000| + +--+---+-----+--+----+---+-----+~~ + + addresses: 0 ... + + +File: as.info, Node: As Sections, Next: Sub-Sections, Prev: Ld Sections, Up: Sections + +4.3 Assembler Internal Sections +=============================== + +These sections are meant only for the internal use of `as'. They have +no meaning at run-time. You do not really need to know about these +sections for most purposes; but they can be mentioned in `as' warning +messages, so it might be helpful to have an idea of their meanings to +`as'. These sections are used to permit the value of every expression +in your assembly language program to be a section-relative address. + +ASSEMBLER-INTERNAL-LOGIC-ERROR! + An internal assembler logic error has been found. This means + there is a bug in the assembler. + +expr section + The assembler stores complex expression internally as combinations + of symbols. When it needs to represent an expression as a symbol, + it puts it in the expr section. + + +File: as.info, Node: Sub-Sections, Next: bss, Prev: As Sections, Up: Sections + +4.4 Sub-Sections +================ + +Assembled bytes conventionally fall into two sections: text and data. +You may have separate groups of data in named sections that you want to +end up near to each other in the object file, even though they are not +contiguous in the assembler source. `as' allows you to use +"subsections" for this purpose. Within each section, there can be +numbered subsections with values from 0 to 8192. Objects assembled +into the same subsection go into the object file together with other +objects in the same subsection. For example, a compiler might want to +store constants in the text section, but might not want to have them +interspersed with the program being assembled. In this case, the +compiler could issue a `.text 0' before each section of code being +output, and a `.text 1' before each group of constants being output. + +Subsections are optional. If you do not use subsections, everything +goes in subsection number zero. + + Each subsection is zero-padded up to a multiple of four bytes. +(Subsections may be padded a different amount on different flavors of +`as'.) + + Subsections appear in your object file in numeric order, lowest +numbered to highest. (All this to be compatible with other people's +assemblers.) The object file contains no representation of +subsections; `ld' and other programs that manipulate object files see +no trace of them. They just see all your text subsections as a text +section, and all your data subsections as a data section. + + To specify which subsection you want subsequent statements assembled +into, use a numeric argument to specify it, in a `.text EXPRESSION' or +a `.data EXPRESSION' statement. When generating COFF output, you can +also use an extra subsection argument with arbitrary named sections: +`.section NAME, EXPRESSION'. When generating ELF output, you can also +use the `.subsection' directive (*note SubSection::) to specify a +subsection: `.subsection EXPRESSION'. EXPRESSION should be an absolute +expression (*note Expressions::). If you just say `.text' then `.text +0' is assumed. Likewise `.data' means `.data 0'. Assembly begins in +`text 0'. For instance: + .text 0 # The default subsection is text 0 anyway. + .ascii "This lives in the first text subsection. *" + .text 1 + .ascii "But this lives in the second text subsection." + .data 0 + .ascii "This lives in the data section," + .ascii "in the first data subsection." + .text 0 + .ascii "This lives in the first text section," + .ascii "immediately following the asterisk (*)." + + Each section has a "location counter" incremented by one for every +byte assembled into that section. Because subsections are merely a +convenience restricted to `as' there is no concept of a subsection +location counter. There is no way to directly manipulate a location +counter--but the `.align' directive changes it, and any label +definition captures its current value. The location counter of the +section where statements are being assembled is said to be the "active" +location counter. + + +File: as.info, Node: bss, Prev: Sub-Sections, Up: Sections + +4.5 bss Section +=============== + +The bss section is used for local common variable storage. You may +allocate address space in the bss section, but you may not dictate data +to load into it before your program executes. When your program starts +running, all the contents of the bss section are zeroed bytes. + + The `.lcomm' pseudo-op defines a symbol in the bss section; see +*Note `.lcomm': Lcomm. + + The `.comm' pseudo-op may be used to declare a common symbol, which +is another form of uninitialized symbol; see *Note `.comm': Comm. + + When assembling for a target which supports multiple sections, such +as ELF or COFF, you may switch into the `.bss' section and define +symbols as usual; see *Note `.section': Section. You may only assemble +zero values into the section. Typically the section will only contain +symbol definitions and `.skip' directives (*note `.skip': Skip.). + + +File: as.info, Node: Symbols, Next: Expressions, Prev: Sections, Up: Top + +5 Symbols +********* + +Symbols are a central concept: the programmer uses symbols to name +things, the linker uses symbols to link, and the debugger uses symbols +to debug. + + _Warning:_ `as' does not place symbols in the object file in the + same order they were declared. This may break some debuggers. + +* Menu: + +* Labels:: Labels +* Setting Symbols:: Giving Symbols Other Values +* Symbol Names:: Symbol Names +* Dot:: The Special Dot Symbol +* Symbol Attributes:: Symbol Attributes + + +File: as.info, Node: Labels, Next: Setting Symbols, Up: Symbols + +5.1 Labels +========== + +A "label" is written as a symbol immediately followed by a colon `:'. +The symbol then represents the current value of the active location +counter, and is, for example, a suitable instruction operand. You are +warned if you use the same symbol to represent two different locations: +the first definition overrides any other definitions. + + On the HPPA, the usual form for a label need not be immediately +followed by a colon, but instead must start in column zero. Only one +label may be defined on a single line. To work around this, the HPPA +version of `as' also provides a special directive `.label' for defining +labels more flexibly. + + +File: as.info, Node: Setting Symbols, Next: Symbol Names, Prev: Labels, Up: Symbols + +5.2 Giving Symbols Other Values +=============================== + +A symbol can be given an arbitrary value by writing a symbol, followed +by an equals sign `=', followed by an expression (*note Expressions::). +This is equivalent to using the `.set' directive. *Note `.set': Set. +In the same way, using a double equals sign `='`=' here represents an +equivalent of the `.eqv' directive. *Note `.eqv': Eqv. + + Blackfin does not support symbol assignment with `='. + + +File: as.info, Node: Symbol Names, Next: Dot, Prev: Setting Symbols, Up: Symbols + +5.3 Symbol Names +================ + +Symbol names begin with a letter or with one of `._'. On most +machines, you can also use `$' in symbol names; exceptions are noted in +*Note Machine Dependencies::. That character may be followed by any +string of digits, letters, dollar signs (unless otherwise noted for a +particular target machine), and underscores. + +Case of letters is significant: `foo' is a different symbol name than +`Foo'. + + Each symbol has exactly one name. Each name in an assembly language +program refers to exactly one symbol. You may use that symbol name any +number of times in a program. + +Local Symbol Names +------------------ + +A local symbol is any symbol beginning with certain local label +prefixes. By default, the local label prefix is `.L' for ELF systems or +`L' for traditional a.out systems, but each target may have its own set +of local label prefixes. On the HPPA local symbols begin with `L$'. + + Local symbols are defined and used within the assembler, but they are +normally not saved in object files. Thus, they are not visible when +debugging. You may use the `-L' option (*note Include Local Symbols: +`-L': L.) to retain the local symbols in the object files. + +Local Labels +------------ + +Local labels help compilers and programmers use names temporarily. +They create symbols which are guaranteed to be unique over the entire +scope of the input source code and which can be referred to by a simple +notation. To define a local label, write a label of the form `N:' +(where N represents any positive integer). To refer to the most recent +previous definition of that label write `Nb', using the same number as +when you defined the label. To refer to the next definition of a local +label, write `Nf'--the `b' stands for "backwards" and the `f' stands +for "forwards". + + There is no restriction on how you can use these labels, and you can +reuse them too. So that it is possible to repeatedly define the same +local label (using the same number `N'), although you can only refer to +the most recently defined local label of that number (for a backwards +reference) or the next definition of a specific local label for a +forward reference. It is also worth noting that the first 10 local +labels (`0:'...`9:') are implemented in a slightly more efficient +manner than the others. + + Here is an example: + + 1: branch 1f + 2: branch 1b + 1: branch 2f + 2: branch 1b + + Which is the equivalent of: + + label_1: branch label_3 + label_2: branch label_1 + label_3: branch label_4 + label_4: branch label_3 + + Local label names are only a notational device. They are immediately +transformed into more conventional symbol names before the assembler +uses them. The symbol names are stored in the symbol table, appear in +error messages, and are optionally emitted to the object file. The +names are constructed using these parts: + +`_local label prefix_' + All local symbols begin with the system-specific local label + prefix. Normally both `as' and `ld' forget symbols that start + with the local label prefix. These labels are used for symbols + you are never intended to see. If you use the `-L' option then + `as' retains these symbols in the object file. If you also + instruct `ld' to retain these symbols, you may use them in + debugging. + +`NUMBER' + This is the number that was used in the local label definition. + So if the label is written `55:' then the number is `55'. + +`C-B' + This unusual character is included so you do not accidentally + invent a symbol of the same name. The character has ASCII value + of `\002' (control-B). + +`_ordinal number_' + This is a serial number to keep the labels distinct. The first + definition of `0:' gets the number `1'. The 15th definition of + `0:' gets the number `15', and so on. Likewise the first + definition of `1:' gets the number `1' and its 15th definition + gets `15' as well. + + So for example, the first `1:' may be named `.L1C-B1', and the 44th +`3:' may be named `.L3C-B44'. + +Dollar Local Labels +------------------- + +`as' also supports an even more local form of local labels called +dollar labels. These labels go out of scope (i.e., they become +undefined) as soon as a non-local label is defined. Thus they remain +valid for only a small region of the input source code. Normal local +labels, by contrast, remain in scope for the entire file, or until they +are redefined by another occurrence of the same local label. + + Dollar labels are defined in exactly the same way as ordinary local +labels, except that they have a dollar sign suffix to their numeric +value, e.g., `55$:'. + + They can also be distinguished from ordinary local labels by their +transformed names which use ASCII character `\001' (control-A) as the +magic character to distinguish them from ordinary labels. For example, +the fifth definition of `6$' may be named `.L6C-A5'. + + +File: as.info, Node: Dot, Next: Symbol Attributes, Prev: Symbol Names, Up: Symbols + +5.4 The Special Dot Symbol +========================== + +The special symbol `.' refers to the current address that `as' is +assembling into. Thus, the expression `melvin: .long .' defines +`melvin' to contain its own address. Assigning a value to `.' is +treated the same as a `.org' directive. Thus, the expression `.=.+4' +is the same as saying `.space 4'. + + +File: as.info, Node: Symbol Attributes, Prev: Dot, Up: Symbols + +5.5 Symbol Attributes +===================== + +Every symbol has, as well as its name, the attributes "Value" and +"Type". Depending on output format, symbols can also have auxiliary +attributes. + + If you use a symbol without defining it, `as' assumes zero for all +these attributes, and probably won't warn you. This makes the symbol +an externally defined symbol, which is generally what you would want. + +* Menu: + +* Symbol Value:: Value +* Symbol Type:: Type + + +* a.out Symbols:: Symbol Attributes: `a.out' + +* COFF Symbols:: Symbol Attributes for COFF + +* SOM Symbols:: Symbol Attributes for SOM + + +File: as.info, Node: Symbol Value, Next: Symbol Type, Up: Symbol Attributes + +5.5.1 Value +----------- + +The value of a symbol is (usually) 32 bits. For a symbol which labels a +location in the text, data, bss or absolute sections the value is the +number of addresses from the start of that section to the label. +Naturally for text, data and bss sections the value of a symbol changes +as `ld' changes section base addresses during linking. Absolute +symbols' values do not change during linking: that is why they are +called absolute. + + The value of an undefined symbol is treated in a special way. If it +is 0 then the symbol is not defined in this assembler source file, and +`ld' tries to determine its value from other files linked into the same +program. You make this kind of symbol simply by mentioning a symbol +name without defining it. A non-zero value represents a `.comm' common +declaration. The value is how much common storage to reserve, in bytes +(addresses). The symbol refers to the first address of the allocated +storage. + + +File: as.info, Node: Symbol Type, Next: a.out Symbols, Prev: Symbol Value, Up: Symbol Attributes + +5.5.2 Type +---------- + +The type attribute of a symbol contains relocation (section) +information, any flag settings indicating that a symbol is external, and +(optionally), other information for linkers and debuggers. The exact +format depends on the object-code output format in use. + + +File: as.info, Node: a.out Symbols, Next: COFF Symbols, Prev: Symbol Type, Up: Symbol Attributes + +5.5.3 Symbol Attributes: `a.out' +-------------------------------- + +* Menu: + +* Symbol Desc:: Descriptor +* Symbol Other:: Other + + +File: as.info, Node: Symbol Desc, Next: Symbol Other, Up: a.out Symbols + +5.5.3.1 Descriptor +.................. + +This is an arbitrary 16-bit value. You may establish a symbol's +descriptor value by using a `.desc' statement (*note `.desc': Desc.). +A descriptor value means nothing to `as'. + + +File: as.info, Node: Symbol Other, Prev: Symbol Desc, Up: a.out Symbols + +5.5.3.2 Other +............. + +This is an arbitrary 8-bit value. It means nothing to `as'. + + +File: as.info, Node: COFF Symbols, Next: SOM Symbols, Prev: a.out Symbols, Up: Symbol Attributes + +5.5.4 Symbol Attributes for COFF +-------------------------------- + +The COFF format supports a multitude of auxiliary symbol attributes; +like the primary symbol attributes, they are set between `.def' and +`.endef' directives. + +5.5.4.1 Primary Attributes +.......................... + +The symbol name is set with `.def'; the value and type, respectively, +with `.val' and `.type'. + +5.5.4.2 Auxiliary Attributes +............................ + +The `as' directives `.dim', `.line', `.scl', `.size', `.tag', and +`.weak' can generate auxiliary symbol table information for COFF. + + +File: as.info, Node: SOM Symbols, Prev: COFF Symbols, Up: Symbol Attributes + +5.5.5 Symbol Attributes for SOM +------------------------------- + +The SOM format for the HPPA supports a multitude of symbol attributes +set with the `.EXPORT' and `.IMPORT' directives. + + The attributes are described in `HP9000 Series 800 Assembly Language +Reference Manual' (HP 92432-90001) under the `IMPORT' and `EXPORT' +assembler directive documentation. + + +File: as.info, Node: Expressions, Next: Pseudo Ops, Prev: Symbols, Up: Top + +6 Expressions +************* + +An "expression" specifies an address or numeric value. Whitespace may +precede and/or follow an expression. + + The result of an expression must be an absolute number, or else an +offset into a particular section. If an expression is not absolute, +and there is not enough information when `as' sees the expression to +know its section, a second pass over the source program might be +necessary to interpret the expression--but the second pass is currently +not implemented. `as' aborts with an error message in this situation. + +* Menu: + +* Empty Exprs:: Empty Expressions +* Integer Exprs:: Integer Expressions + + +File: as.info, Node: Empty Exprs, Next: Integer Exprs, Up: Expressions + +6.1 Empty Expressions +===================== + +An empty expression has no value: it is just whitespace or null. +Wherever an absolute expression is required, you may omit the +expression, and `as' assumes a value of (absolute) 0. This is +compatible with other assemblers. + + +File: as.info, Node: Integer Exprs, Prev: Empty Exprs, Up: Expressions + +6.2 Integer Expressions +======================= + +An "integer expression" is one or more _arguments_ delimited by +_operators_. + +* Menu: + +* Arguments:: Arguments +* Operators:: Operators +* Prefix Ops:: Prefix Operators +* Infix Ops:: Infix Operators + + +File: as.info, Node: Arguments, Next: Operators, Up: Integer Exprs + +6.2.1 Arguments +--------------- + +"Arguments" are symbols, numbers or subexpressions. In other contexts +arguments are sometimes called "arithmetic operands". In this manual, +to avoid confusing them with the "instruction operands" of the machine +language, we use the term "argument" to refer to parts of expressions +only, reserving the word "operand" to refer only to machine instruction +operands. + + Symbols are evaluated to yield {SECTION NNN} where SECTION is one of +text, data, bss, absolute, or undefined. NNN is a signed, 2's +complement 32 bit integer. + + Numbers are usually integers. + + A number can be a flonum or bignum. In this case, you are warned +that only the low order 32 bits are used, and `as' pretends these 32 +bits are an integer. You may write integer-manipulating instructions +that act on exotic constants, compatible with other assemblers. + + Subexpressions are a left parenthesis `(' followed by an integer +expression, followed by a right parenthesis `)'; or a prefix operator +followed by an argument. + + +File: as.info, Node: Operators, Next: Prefix Ops, Prev: Arguments, Up: Integer Exprs + +6.2.2 Operators +--------------- + +"Operators" are arithmetic functions, like `+' or `%'. Prefix +operators are followed by an argument. Infix operators appear between +their arguments. Operators may be preceded and/or followed by +whitespace. + + +File: as.info, Node: Prefix Ops, Next: Infix Ops, Prev: Operators, Up: Integer Exprs + +6.2.3 Prefix Operator +--------------------- + +`as' has the following "prefix operators". They each take one +argument, which must be absolute. + +`-' + "Negation". Two's complement negation. + +`~' + "Complementation". Bitwise not. + + +File: as.info, Node: Infix Ops, Prev: Prefix Ops, Up: Integer Exprs + +6.2.4 Infix Operators +--------------------- + +"Infix operators" take two arguments, one on either side. Operators +have precedence, but operations with equal precedence are performed left +to right. Apart from `+' or `-', both arguments must be absolute, and +the result is absolute. + + 1. Highest Precedence + + `*' + "Multiplication". + + `/' + "Division". Truncation is the same as the C operator `/' + + `%' + "Remainder". + + `<<' + "Shift Left". Same as the C operator `<<'. + + `>>' + "Shift Right". Same as the C operator `>>'. + + 2. Intermediate precedence + + `|' + "Bitwise Inclusive Or". + + `&' + "Bitwise And". + + `^' + "Bitwise Exclusive Or". + + `!' + "Bitwise Or Not". + + 3. Low Precedence + + `+' + "Addition". If either argument is absolute, the result has + the section of the other argument. You may not add together + arguments from different sections. + + `-' + "Subtraction". If the right argument is absolute, the result + has the section of the left argument. If both arguments are + in the same section, the result is absolute. You may not + subtract arguments from different sections. + + `==' + "Is Equal To" + + `<>' + `!=' + "Is Not Equal To" + + `<' + "Is Less Than" + + `>' + "Is Greater Than" + + `>=' + "Is Greater Than Or Equal To" + + `<=' + "Is Less Than Or Equal To" + + The comparison operators can be used as infix operators. A + true results has a value of -1 whereas a false result has a + value of 0. Note, these operators perform signed + comparisons. + + 4. Lowest Precedence + + `&&' + "Logical And". + + `||' + "Logical Or". + + These two logical operations can be used to combine the + results of sub expressions. Note, unlike the comparison + operators a true result returns a value of 1 but a false + results does still return 0. Also note that the logical or + operator has a slightly lower precedence than logical and. + + + In short, it's only meaningful to add or subtract the _offsets_ in an +address; you can only have a defined section in one of the two +arguments. + + +File: as.info, Node: Pseudo Ops, Next: Object Attributes, Prev: Expressions, Up: Top + +7 Assembler Directives +********************** + +All assembler directives have names that begin with a period (`.'). +The rest of the name is letters, usually in lower case. + + This chapter discusses directives that are available regardless of +the target machine configuration for the GNU assembler. Some machine +configurations provide additional directives. *Note Machine +Dependencies::. + +* Menu: + +* Abort:: `.abort' + +* ABORT (COFF):: `.ABORT' + +* Align:: `.align ABS-EXPR , ABS-EXPR' +* Altmacro:: `.altmacro' +* Ascii:: `.ascii "STRING"'... +* Asciz:: `.asciz "STRING"'... +* Balign:: `.balign ABS-EXPR , ABS-EXPR' +* Byte:: `.byte EXPRESSIONS' +* CFI directives:: `.cfi_startproc [simple]', `.cfi_endproc', etc. +* Comm:: `.comm SYMBOL , LENGTH ' +* Data:: `.data SUBSECTION' + +* Def:: `.def NAME' + +* Desc:: `.desc SYMBOL, ABS-EXPRESSION' + +* Dim:: `.dim' + +* Double:: `.double FLONUMS' +* Eject:: `.eject' +* Else:: `.else' +* Elseif:: `.elseif' +* End:: `.end' + +* Endef:: `.endef' + +* Endfunc:: `.endfunc' +* Endif:: `.endif' +* Equ:: `.equ SYMBOL, EXPRESSION' +* Equiv:: `.equiv SYMBOL, EXPRESSION' +* Eqv:: `.eqv SYMBOL, EXPRESSION' +* Err:: `.err' +* Error:: `.error STRING' +* Exitm:: `.exitm' +* Extern:: `.extern' +* Fail:: `.fail' +* File:: `.file' +* Fill:: `.fill REPEAT , SIZE , VALUE' +* Float:: `.float FLONUMS' +* Func:: `.func' +* Global:: `.global SYMBOL', `.globl SYMBOL' + +* Gnu_attribute:: `.gnu_attribute TAG,VALUE' +* Hidden:: `.hidden NAMES' + +* hword:: `.hword EXPRESSIONS' +* Ident:: `.ident' +* If:: `.if ABSOLUTE EXPRESSION' +* Incbin:: `.incbin "FILE"[,SKIP[,COUNT]]' +* Include:: `.include "FILE"' +* Int:: `.int EXPRESSIONS' + +* Internal:: `.internal NAMES' + +* Irp:: `.irp SYMBOL,VALUES'... +* Irpc:: `.irpc SYMBOL,VALUES'... +* Lcomm:: `.lcomm SYMBOL , LENGTH' +* Lflags:: `.lflags' + +* Line:: `.line LINE-NUMBER' + +* Linkonce:: `.linkonce [TYPE]' +* List:: `.list' +* Ln:: `.ln LINE-NUMBER' +* Loc:: `.loc FILENO LINENO' +* Loc_mark_labels:: `.loc_mark_labels ENABLE' + +* Local:: `.local NAMES' + +* Long:: `.long EXPRESSIONS' + +* Macro:: `.macro NAME ARGS'... +* MRI:: `.mri VAL' +* Noaltmacro:: `.noaltmacro' +* Nolist:: `.nolist' +* Octa:: `.octa BIGNUMS' +* Org:: `.org NEW-LC, FILL' +* P2align:: `.p2align ABS-EXPR, ABS-EXPR, ABS-EXPR' + +* PopSection:: `.popsection' +* Previous:: `.previous' + +* Print:: `.print STRING' + +* Protected:: `.protected NAMES' + +* Psize:: `.psize LINES, COLUMNS' +* Purgem:: `.purgem NAME' + +* PushSection:: `.pushsection NAME' + +* Quad:: `.quad BIGNUMS' +* Reloc:: `.reloc OFFSET, RELOC_NAME[, EXPRESSION]' +* Rept:: `.rept COUNT' +* Sbttl:: `.sbttl "SUBHEADING"' + +* Scl:: `.scl CLASS' + +* Section:: `.section NAME[, FLAGS]' + +* Set:: `.set SYMBOL, EXPRESSION' +* Short:: `.short EXPRESSIONS' +* Single:: `.single FLONUMS' + +* Size:: `.size [NAME , EXPRESSION]' + +* Skip:: `.skip SIZE , FILL' + +* Sleb128:: `.sleb128 EXPRESSIONS' + +* Space:: `.space SIZE , FILL' + +* Stab:: `.stabd, .stabn, .stabs' + +* String:: `.string "STR"', `.string8 "STR"', `.string16 "STR"', `.string32 "STR"', `.string64 "STR"' +* Struct:: `.struct EXPRESSION' + +* SubSection:: `.subsection' +* Symver:: `.symver NAME,NAME2@NODENAME' + + +* Tag:: `.tag STRUCTNAME' + +* Text:: `.text SUBSECTION' +* Title:: `.title "HEADING"' + +* Type:: `.type <INT | NAME , TYPE DESCRIPTION>' + +* Uleb128:: `.uleb128 EXPRESSIONS' + +* Val:: `.val ADDR' + + +* Version:: `.version "STRING"' +* VTableEntry:: `.vtable_entry TABLE, OFFSET' +* VTableInherit:: `.vtable_inherit CHILD, PARENT' + +* Warning:: `.warning STRING' +* Weak:: `.weak NAMES' +* Weakref:: `.weakref ALIAS, SYMBOL' +* Word:: `.word EXPRESSIONS' +* Deprecated:: Deprecated Directives + + +File: as.info, Node: Abort, Next: ABORT (COFF), Up: Pseudo Ops + +7.1 `.abort' +============ + +This directive stops the assembly immediately. It is for compatibility +with other assemblers. The original idea was that the assembly +language source would be piped into the assembler. If the sender of +the source quit, it could use this directive tells `as' to quit also. +One day `.abort' will not be supported. + + +File: as.info, Node: ABORT (COFF), Next: Align, Prev: Abort, Up: Pseudo Ops + +7.2 `.ABORT' (COFF) +=================== + +When producing COFF output, `as' accepts this directive as a synonym +for `.abort'. + + +File: as.info, Node: Align, Next: Altmacro, Prev: ABORT (COFF), Up: Pseudo Ops + +7.3 `.align ABS-EXPR, ABS-EXPR, ABS-EXPR' +========================================= + +Pad the location counter (in the current subsection) to a particular +storage boundary. The first expression (which must be absolute) is the +alignment required, as described below. + + The second expression (also absolute) gives the fill value to be +stored in the padding bytes. It (and the comma) may be omitted. If it +is omitted, the padding bytes are normally zero. However, on some +systems, if the section is marked as containing code and the fill value +is omitted, the space is filled with no-op instructions. + + The third expression is also absolute, and is also optional. If it +is present, it is the maximum number of bytes that should be skipped by +this alignment directive. If doing the alignment would require +skipping more bytes than the specified maximum, then the alignment is +not done at all. You can omit the fill value (the second argument) +entirely by simply using two commas after the required alignment; this +can be useful if you want the alignment to be filled with no-op +instructions when appropriate. + + The way the required alignment is specified varies from system to +system. For the arc, hppa, i386 using ELF, i860, iq2000, m68k, or32, +s390, sparc, tic4x, tic80 and xtensa, the first expression is the +alignment request in bytes. For example `.align 8' advances the +location counter until it is a multiple of 8. If the location counter +is already a multiple of 8, no change is needed. For the tic54x, the +first expression is the alignment request in words. + + For other systems, including ppc, i386 using a.out format, arm and +strongarm, it is the number of low-order zero bits the location counter +must have after advancement. For example `.align 3' advances the +location counter until it a multiple of 8. If the location counter is +already a multiple of 8, no change is needed. + + This inconsistency is due to the different behaviors of the various +native assemblers for these systems which GAS must emulate. GAS also +provides `.balign' and `.p2align' directives, described later, which +have a consistent behavior across all architectures (but are specific +to GAS). + + +File: as.info, Node: Altmacro, Next: Ascii, Prev: Align, Up: Pseudo Ops + +7.4 `.altmacro' +=============== + +Enable alternate macro mode, enabling: + +`LOCAL NAME [ , ... ]' + One additional directive, `LOCAL', is available. It is used to + generate a string replacement for each of the NAME arguments, and + replace any instances of NAME in each macro expansion. The + replacement string is unique in the assembly, and different for + each separate macro expansion. `LOCAL' allows you to write macros + that define symbols, without fear of conflict between separate + macro expansions. + +`String delimiters' + You can write strings delimited in these other ways besides + `"STRING"': + + `'STRING'' + You can delimit strings with single-quote characters. + + `<STRING>' + You can delimit strings with matching angle brackets. + +`single-character string escape' + To include any single character literally in a string (even if the + character would otherwise have some special meaning), you can + prefix the character with `!' (an exclamation mark). For example, + you can write `<4.3 !> 5.4!!>' to get the literal text `4.3 > + 5.4!'. + +`Expression results as strings' + You can write `%EXPR' to evaluate the expression EXPR and use the + result as a string. + + +File: as.info, Node: Ascii, Next: Asciz, Prev: Altmacro, Up: Pseudo Ops + +7.5 `.ascii "STRING"'... +======================== + +`.ascii' expects zero or more string literals (*note Strings::) +separated by commas. It assembles each string (with no automatic +trailing zero byte) into consecutive addresses. + + +File: as.info, Node: Asciz, Next: Balign, Prev: Ascii, Up: Pseudo Ops + +7.6 `.asciz "STRING"'... +======================== + +`.asciz' is just like `.ascii', but each string is followed by a zero +byte. The "z" in `.asciz' stands for "zero". + + +File: as.info, Node: Balign, Next: Byte, Prev: Asciz, Up: Pseudo Ops + +7.7 `.balign[wl] ABS-EXPR, ABS-EXPR, ABS-EXPR' +============================================== + +Pad the location counter (in the current subsection) to a particular +storage boundary. The first expression (which must be absolute) is the +alignment request in bytes. For example `.balign 8' advances the +location counter until it is a multiple of 8. If the location counter +is already a multiple of 8, no change is needed. + + The second expression (also absolute) gives the fill value to be +stored in the padding bytes. It (and the comma) may be omitted. If it +is omitted, the padding bytes are normally zero. However, on some +systems, if the section is marked as containing code and the fill value +is omitted, the space is filled with no-op instructions. + + The third expression is also absolute, and is also optional. If it +is present, it is the maximum number of bytes that should be skipped by +this alignment directive. If doing the alignment would require +skipping more bytes than the specified maximum, then the alignment is +not done at all. You can omit the fill value (the second argument) +entirely by simply using two commas after the required alignment; this +can be useful if you want the alignment to be filled with no-op +instructions when appropriate. + + The `.balignw' and `.balignl' directives are variants of the +`.balign' directive. The `.balignw' directive treats the fill pattern +as a two byte word value. The `.balignl' directives treats the fill +pattern as a four byte longword value. For example, `.balignw +4,0x368d' will align to a multiple of 4. If it skips two bytes, they +will be filled in with the value 0x368d (the exact placement of the +bytes depends upon the endianness of the processor). If it skips 1 or +3 bytes, the fill value is undefined. + + +File: as.info, Node: Byte, Next: CFI directives, Prev: Balign, Up: Pseudo Ops + +7.8 `.byte EXPRESSIONS' +======================= + +`.byte' expects zero or more expressions, separated by commas. Each +expression is assembled into the next byte. + + +File: as.info, Node: CFI directives, Next: Comm, Prev: Byte, Up: Pseudo Ops + +7.9 `.cfi_startproc [simple]' +============================= + +`.cfi_startproc' is used at the beginning of each function that should +have an entry in `.eh_frame'. It initializes some internal data +structures. Don't forget to close the function by `.cfi_endproc'. + +7.10 `.cfi_sections SECTION_LIST' +================================= + +`.cfi_sections' may be used to specify whether CFI directives should +emit `.eh_frame' section and/or `.debug_frame' section. If +SECTION_LIST is `.eh_frame', `.eh_frame' is emitted, if SECTION_LIST is +`.debug_frame', `.debug_frame' is emitted. To emit both use +`.eh_frame, .debug_frame'. The default if this directive is not used +is `.cfi_sections .eh_frame'. + + Unless `.cfi_startproc' is used along with parameter `simple' it +also emits some architecture dependent initial CFI instructions. + +7.11 `.cfi_endproc' +=================== + +`.cfi_endproc' is used at the end of a function where it closes its +unwind entry previously opened by `.cfi_startproc', and emits it to +`.eh_frame'. + +7.12 `.cfi_personality ENCODING [, EXP]' +======================================== + +`.cfi_personality' defines personality routine and its encoding. +ENCODING must be a constant determining how the personality should be +encoded. If it is 255 (`DW_EH_PE_omit'), second argument is not +present, otherwise second argument should be a constant or a symbol +name. When using indirect encodings, the symbol provided should be the +location where personality can be loaded from, not the personality +routine itself. The default after `.cfi_startproc' is +`.cfi_personality 0xff', no personality routine. + +7.13 `.cfi_lsda ENCODING [, EXP]' +================================= + +`.cfi_lsda' defines LSDA and its encoding. ENCODING must be a constant +determining how the LSDA should be encoded. If it is 255 +(`DW_EH_PE_omit'), second argument is not present, otherwise second +argument should be a constant or a symbol name. The default after +`.cfi_startproc' is `.cfi_lsda 0xff', no LSDA. + +7.14 `.cfi_def_cfa REGISTER, OFFSET' +==================================== + +`.cfi_def_cfa' defines a rule for computing CFA as: take address from +REGISTER and add OFFSET to it. + +7.15 `.cfi_def_cfa_register REGISTER' +===================================== + +`.cfi_def_cfa_register' modifies a rule for computing CFA. From now on +REGISTER will be used instead of the old one. Offset remains the same. + +7.16 `.cfi_def_cfa_offset OFFSET' +================================= + +`.cfi_def_cfa_offset' modifies a rule for computing CFA. Register +remains the same, but OFFSET is new. Note that it is the absolute +offset that will be added to a defined register to compute CFA address. + +7.17 `.cfi_adjust_cfa_offset OFFSET' +==================================== + +Same as `.cfi_def_cfa_offset' but OFFSET is a relative value that is +added/substracted from the previous offset. + +7.18 `.cfi_offset REGISTER, OFFSET' +=================================== + +Previous value of REGISTER is saved at offset OFFSET from CFA. + +7.19 `.cfi_rel_offset REGISTER, OFFSET' +======================================= + +Previous value of REGISTER is saved at offset OFFSET from the current +CFA register. This is transformed to `.cfi_offset' using the known +displacement of the CFA register from the CFA. This is often easier to +use, because the number will match the code it's annotating. + +7.20 `.cfi_register REGISTER1, REGISTER2' +========================================= + +Previous value of REGISTER1 is saved in register REGISTER2. + +7.21 `.cfi_restore REGISTER' +============================ + +`.cfi_restore' says that the rule for REGISTER is now the same as it +was at the beginning of the function, after all initial instruction +added by `.cfi_startproc' were executed. + +7.22 `.cfi_undefined REGISTER' +============================== + +From now on the previous value of REGISTER can't be restored anymore. + +7.23 `.cfi_same_value REGISTER' +=============================== + +Current value of REGISTER is the same like in the previous frame, i.e. +no restoration needed. + +7.24 `.cfi_remember_state', +=========================== + +First save all current rules for all registers by `.cfi_remember_state', +then totally screw them up by subsequent `.cfi_*' directives and when +everything is hopelessly bad, use `.cfi_restore_state' to restore the +previous saved state. + +7.25 `.cfi_return_column REGISTER' +================================== + +Change return column REGISTER, i.e. the return address is either +directly in REGISTER or can be accessed by rules for REGISTER. + +7.26 `.cfi_signal_frame' +======================== + +Mark current function as signal trampoline. + +7.27 `.cfi_window_save' +======================= + +SPARC register window has been saved. + +7.28 `.cfi_escape' EXPRESSION[, ...] +==================================== + +Allows the user to add arbitrary bytes to the unwind info. One might +use this to add OS-specific CFI opcodes, or generic CFI opcodes that +GAS does not yet support. + +7.29 `.cfi_val_encoded_addr REGISTER, ENCODING, LABEL' +====================================================== + +The current value of REGISTER is LABEL. The value of LABEL will be +encoded in the output file according to ENCODING; see the description +of `.cfi_personality' for details on this encoding. + + The usefulness of equating a register to a fixed label is probably +limited to the return address register. Here, it can be useful to mark +a code segment that has only one return address which is reached by a +direct branch and no copy of the return address exists in memory or +another register. + + +File: as.info, Node: Comm, Next: Data, Prev: CFI directives, Up: Pseudo Ops + +7.30 `.comm SYMBOL , LENGTH ' +============================= + +`.comm' declares a common symbol named SYMBOL. When linking, a common +symbol in one object file may be merged with a defined or common symbol +of the same name in another object file. If `ld' does not see a +definition for the symbol-just one or more common symbols-then it will +allocate LENGTH bytes of uninitialized memory. LENGTH must be an +absolute expression. If `ld' sees multiple common symbols with the +same name, and they do not all have the same size, it will allocate +space using the largest size. + + When using ELF or (as a GNU extension) PE, the `.comm' directive +takes an optional third argument. This is the desired alignment of the +symbol, specified for ELF as a byte boundary (for example, an alignment +of 16 means that the least significant 4 bits of the address should be +zero), and for PE as a power of two (for example, an alignment of 5 +means aligned to a 32-byte boundary). The alignment must be an +absolute expression, and it must be a power of two. If `ld' allocates +uninitialized memory for the common symbol, it will use the alignment +when placing the symbol. If no alignment is specified, `as' will set +the alignment to the largest power of two less than or equal to the +size of the symbol, up to a maximum of 16 on ELF, or the default +section alignment of 4 on PE(1). + + The syntax for `.comm' differs slightly on the HPPA. The syntax is +`SYMBOL .comm, LENGTH'; SYMBOL is optional. + + ---------- Footnotes ---------- + + (1) This is not the same as the executable image file alignment +controlled by `ld''s `--section-alignment' option; image file sections +in PE are aligned to multiples of 4096, which is far too large an +alignment for ordinary variables. It is rather the default alignment +for (non-debug) sections within object (`*.o') files, which are less +strictly aligned. + + +File: as.info, Node: Data, Next: Def, Prev: Comm, Up: Pseudo Ops + +7.31 `.data SUBSECTION' +======================= + +`.data' tells `as' to assemble the following statements onto the end of +the data subsection numbered SUBSECTION (which is an absolute +expression). If SUBSECTION is omitted, it defaults to zero. + + +File: as.info, Node: Def, Next: Desc, Prev: Data, Up: Pseudo Ops + +7.32 `.def NAME' +================ + +Begin defining debugging information for a symbol NAME; the definition +extends until the `.endef' directive is encountered. + + +File: as.info, Node: Desc, Next: Dim, Prev: Def, Up: Pseudo Ops + +7.33 `.desc SYMBOL, ABS-EXPRESSION' +=================================== + +This directive sets the descriptor of the symbol (*note Symbol +Attributes::) to the low 16 bits of an absolute expression. + + The `.desc' directive is not available when `as' is configured for +COFF output; it is only for `a.out' or `b.out' object format. For the +sake of compatibility, `as' accepts it, but produces no output, when +configured for COFF. + + +File: as.info, Node: Dim, Next: Double, Prev: Desc, Up: Pseudo Ops + +7.34 `.dim' +=========== + +This directive is generated by compilers to include auxiliary debugging +information in the symbol table. It is only permitted inside +`.def'/`.endef' pairs. + + +File: as.info, Node: Double, Next: Eject, Prev: Dim, Up: Pseudo Ops + +7.35 `.double FLONUMS' +====================== + +`.double' expects zero or more flonums, separated by commas. It +assembles floating point numbers. The exact kind of floating point +numbers emitted depends on how `as' is configured. *Note Machine +Dependencies::. + + +File: as.info, Node: Eject, Next: Else, Prev: Double, Up: Pseudo Ops + +7.36 `.eject' +============= + +Force a page break at this point, when generating assembly listings. + + +File: as.info, Node: Else, Next: Elseif, Prev: Eject, Up: Pseudo Ops + +7.37 `.else' +============ + +`.else' is part of the `as' support for conditional assembly; see *Note +`.if': If. It marks the beginning of a section of code to be assembled +if the condition for the preceding `.if' was false. + + +File: as.info, Node: Elseif, Next: End, Prev: Else, Up: Pseudo Ops + +7.38 `.elseif' +============== + +`.elseif' is part of the `as' support for conditional assembly; see +*Note `.if': If. It is shorthand for beginning a new `.if' block that +would otherwise fill the entire `.else' section. + + +File: as.info, Node: End, Next: Endef, Prev: Elseif, Up: Pseudo Ops + +7.39 `.end' +=========== + +`.end' marks the end of the assembly file. `as' does not process +anything in the file past the `.end' directive. + + +File: as.info, Node: Endef, Next: Endfunc, Prev: End, Up: Pseudo Ops + +7.40 `.endef' +============= + +This directive flags the end of a symbol definition begun with `.def'. + + +File: as.info, Node: Endfunc, Next: Endif, Prev: Endef, Up: Pseudo Ops + +7.41 `.endfunc' +=============== + +`.endfunc' marks the end of a function specified with `.func'. + + +File: as.info, Node: Endif, Next: Equ, Prev: Endfunc, Up: Pseudo Ops + +7.42 `.endif' +============= + +`.endif' is part of the `as' support for conditional assembly; it marks +the end of a block of code that is only assembled conditionally. *Note +`.if': If. + + +File: as.info, Node: Equ, Next: Equiv, Prev: Endif, Up: Pseudo Ops + +7.43 `.equ SYMBOL, EXPRESSION' +============================== + +This directive sets the value of SYMBOL to EXPRESSION. It is +synonymous with `.set'; see *Note `.set': Set. + + The syntax for `equ' on the HPPA is `SYMBOL .equ EXPRESSION'. + + The syntax for `equ' on the Z80 is `SYMBOL equ EXPRESSION'. On the +Z80 it is an eror if SYMBOL is already defined, but the symbol is not +protected from later redefinition. Compare *Note Equiv::. + + +File: as.info, Node: Equiv, Next: Eqv, Prev: Equ, Up: Pseudo Ops + +7.44 `.equiv SYMBOL, EXPRESSION' +================================ + +The `.equiv' directive is like `.equ' and `.set', except that the +assembler will signal an error if SYMBOL is already defined. Note a +symbol which has been referenced but not actually defined is considered +to be undefined. + + Except for the contents of the error message, this is roughly +equivalent to + .ifdef SYM + .err + .endif + .equ SYM,VAL + plus it protects the symbol from later redefinition. + + +File: as.info, Node: Eqv, Next: Err, Prev: Equiv, Up: Pseudo Ops + +7.45 `.eqv SYMBOL, EXPRESSION' +============================== + +The `.eqv' directive is like `.equiv', but no attempt is made to +evaluate the expression or any part of it immediately. Instead each +time the resulting symbol is used in an expression, a snapshot of its +current value is taken. + + +File: as.info, Node: Err, Next: Error, Prev: Eqv, Up: Pseudo Ops + +7.46 `.err' +=========== + +If `as' assembles a `.err' directive, it will print an error message +and, unless the `-Z' option was used, it will not generate an object +file. This can be used to signal an error in conditionally compiled +code. + + +File: as.info, Node: Error, Next: Exitm, Prev: Err, Up: Pseudo Ops + +7.47 `.error "STRING"' +====================== + +Similarly to `.err', this directive emits an error, but you can specify +a string that will be emitted as the error message. If you don't +specify the message, it defaults to `".error directive invoked in +source file"'. *Note Error and Warning Messages: Errors. + + .error "This code has not been assembled and tested." + + +File: as.info, Node: Exitm, Next: Extern, Prev: Error, Up: Pseudo Ops + +7.48 `.exitm' +============= + +Exit early from the current macro definition. *Note Macro::. + + +File: as.info, Node: Extern, Next: Fail, Prev: Exitm, Up: Pseudo Ops + +7.49 `.extern' +============== + +`.extern' is accepted in the source program--for compatibility with +other assemblers--but it is ignored. `as' treats all undefined symbols +as external. + + +File: as.info, Node: Fail, Next: File, Prev: Extern, Up: Pseudo Ops + +7.50 `.fail EXPRESSION' +======================= + +Generates an error or a warning. If the value of the EXPRESSION is 500 +or more, `as' will print a warning message. If the value is less than +500, `as' will print an error message. The message will include the +value of EXPRESSION. This can occasionally be useful inside complex +nested macros or conditional assembly. + + +File: as.info, Node: File, Next: Fill, Prev: Fail, Up: Pseudo Ops + +7.51 `.file' +============ + +There are two different versions of the `.file' directive. Targets +that support DWARF2 line number information use the DWARF2 version of +`.file'. Other targets use the default version. + +Default Version +--------------- + +This version of the `.file' directive tells `as' that we are about to +start a new logical file. The syntax is: + + .file STRING + + STRING is the new file name. In general, the filename is recognized +whether or not it is surrounded by quotes `"'; but if you wish to +specify an empty file name, you must give the quotes-`""'. This +statement may go away in future: it is only recognized to be compatible +with old `as' programs. + +DWARF2 Version +-------------- + +When emitting DWARF2 line number information, `.file' assigns filenames +to the `.debug_line' file name table. The syntax is: + + .file FILENO FILENAME + + The FILENO operand should be a unique positive integer to use as the +index of the entry in the table. The FILENAME operand is a C string +literal. + + The detail of filename indices is exposed to the user because the +filename table is shared with the `.debug_info' section of the DWARF2 +debugging information, and thus the user must know the exact indices +that table entries will have. + + +File: as.info, Node: Fill, Next: Float, Prev: File, Up: Pseudo Ops + +7.52 `.fill REPEAT , SIZE , VALUE' +================================== + +REPEAT, SIZE and VALUE are absolute expressions. This emits REPEAT +copies of SIZE bytes. REPEAT may be zero or more. SIZE may be zero or +more, but if it is more than 8, then it is deemed to have the value 8, +compatible with other people's assemblers. The contents of each REPEAT +bytes is taken from an 8-byte number. The highest order 4 bytes are +zero. The lowest order 4 bytes are VALUE rendered in the byte-order of +an integer on the computer `as' is assembling for. Each SIZE bytes in +a repetition is taken from the lowest order SIZE bytes of this number. +Again, this bizarre behavior is compatible with other people's +assemblers. + + SIZE and VALUE are optional. If the second comma and VALUE are +absent, VALUE is assumed zero. If the first comma and following tokens +are absent, SIZE is assumed to be 1. + + +File: as.info, Node: Float, Next: Func, Prev: Fill, Up: Pseudo Ops + +7.53 `.float FLONUMS' +===================== + +This directive assembles zero or more flonums, separated by commas. It +has the same effect as `.single'. The exact kind of floating point +numbers emitted depends on how `as' is configured. *Note Machine +Dependencies::. + + +File: as.info, Node: Func, Next: Global, Prev: Float, Up: Pseudo Ops + +7.54 `.func NAME[,LABEL]' +========================= + +`.func' emits debugging information to denote function NAME, and is +ignored unless the file is assembled with debugging enabled. Only +`--gstabs[+]' is currently supported. LABEL is the entry point of the +function and if omitted NAME prepended with the `leading char' is used. +`leading char' is usually `_' or nothing, depending on the target. All +functions are currently defined to have `void' return type. The +function must be terminated with `.endfunc'. + + +File: as.info, Node: Global, Next: Gnu_attribute, Prev: Func, Up: Pseudo Ops + +7.55 `.global SYMBOL', `.globl SYMBOL' +====================================== + +`.global' makes the symbol visible to `ld'. If you define SYMBOL in +your partial program, its value is made available to other partial +programs that are linked with it. Otherwise, SYMBOL takes its +attributes from a symbol of the same name from another file linked into +the same program. + + Both spellings (`.globl' and `.global') are accepted, for +compatibility with other assemblers. + + On the HPPA, `.global' is not always enough to make it accessible to +other partial programs. You may need the HPPA-only `.EXPORT' directive +as well. *Note HPPA Assembler Directives: HPPA Directives. + + +File: as.info, Node: Gnu_attribute, Next: Hidden, Prev: Global, Up: Pseudo Ops + +7.56 `.gnu_attribute TAG,VALUE' +=============================== + +Record a GNU object attribute for this file. *Note Object Attributes::. + + +File: as.info, Node: Hidden, Next: hword, Prev: Gnu_attribute, Up: Pseudo Ops + +7.57 `.hidden NAMES' +==================== + +This is one of the ELF visibility directives. The other two are +`.internal' (*note `.internal': Internal.) and `.protected' (*note +`.protected': Protected.). + + This directive overrides the named symbols default visibility (which +is set by their binding: local, global or weak). The directive sets +the visibility to `hidden' which means that the symbols are not visible +to other components. Such symbols are always considered to be +`protected' as well. + + +File: as.info, Node: hword, Next: Ident, Prev: Hidden, Up: Pseudo Ops + +7.58 `.hword EXPRESSIONS' +========================= + +This expects zero or more EXPRESSIONS, and emits a 16 bit number for +each. + + This directive is a synonym for `.short'; depending on the target +architecture, it may also be a synonym for `.word'. + + +File: as.info, Node: Ident, Next: If, Prev: hword, Up: Pseudo Ops + +7.59 `.ident' +============= + +This directive is used by some assemblers to place tags in object +files. The behavior of this directive varies depending on the target. +When using the a.out object file format, `as' simply accepts the +directive for source-file compatibility with existing assemblers, but +does not emit anything for it. When using COFF, comments are emitted +to the `.comment' or `.rdata' section, depending on the target. When +using ELF, comments are emitted to the `.comment' section. + + +File: as.info, Node: If, Next: Incbin, Prev: Ident, Up: Pseudo Ops + +7.60 `.if ABSOLUTE EXPRESSION' +============================== + +`.if' marks the beginning of a section of code which is only considered +part of the source program being assembled if the argument (which must +be an ABSOLUTE EXPRESSION) is non-zero. The end of the conditional +section of code must be marked by `.endif' (*note `.endif': Endif.); +optionally, you may include code for the alternative condition, flagged +by `.else' (*note `.else': Else.). If you have several conditions to +check, `.elseif' may be used to avoid nesting blocks if/else within +each subsequent `.else' block. + + The following variants of `.if' are also supported: +`.ifdef SYMBOL' + Assembles the following section of code if the specified SYMBOL + has been defined. Note a symbol which has been referenced but not + yet defined is considered to be undefined. + +`.ifb TEXT' + Assembles the following section of code if the operand is blank + (empty). + +`.ifc STRING1,STRING2' + Assembles the following section of code if the two strings are the + same. The strings may be optionally quoted with single quotes. + If they are not quoted, the first string stops at the first comma, + and the second string stops at the end of the line. Strings which + contain whitespace should be quoted. The string comparison is + case sensitive. + +`.ifeq ABSOLUTE EXPRESSION' + Assembles the following section of code if the argument is zero. + +`.ifeqs STRING1,STRING2' + Another form of `.ifc'. The strings must be quoted using double + quotes. + +`.ifge ABSOLUTE EXPRESSION' + Assembles the following section of code if the argument is greater + than or equal to zero. + +`.ifgt ABSOLUTE EXPRESSION' + Assembles the following section of code if the argument is greater + than zero. + +`.ifle ABSOLUTE EXPRESSION' + Assembles the following section of code if the argument is less + than or equal to zero. + +`.iflt ABSOLUTE EXPRESSION' + Assembles the following section of code if the argument is less + than zero. + +`.ifnb TEXT' + Like `.ifb', but the sense of the test is reversed: this assembles + the following section of code if the operand is non-blank + (non-empty). + +`.ifnc STRING1,STRING2.' + Like `.ifc', but the sense of the test is reversed: this assembles + the following section of code if the two strings are not the same. + +`.ifndef SYMBOL' +`.ifnotdef SYMBOL' + Assembles the following section of code if the specified SYMBOL + has not been defined. Both spelling variants are equivalent. + Note a symbol which has been referenced but not yet defined is + considered to be undefined. + +`.ifne ABSOLUTE EXPRESSION' + Assembles the following section of code if the argument is not + equal to zero (in other words, this is equivalent to `.if'). + +`.ifnes STRING1,STRING2' + Like `.ifeqs', but the sense of the test is reversed: this + assembles the following section of code if the two strings are not + the same. + + +File: as.info, Node: Incbin, Next: Include, Prev: If, Up: Pseudo Ops + +7.61 `.incbin "FILE"[,SKIP[,COUNT]]' +==================================== + +The `incbin' directive includes FILE verbatim at the current location. +You can control the search paths used with the `-I' command-line option +(*note Command-Line Options: Invoking.). Quotation marks are required +around FILE. + + The SKIP argument skips a number of bytes from the start of the +FILE. The COUNT argument indicates the maximum number of bytes to +read. Note that the data is not aligned in any way, so it is the user's +responsibility to make sure that proper alignment is provided both +before and after the `incbin' directive. + + +File: as.info, Node: Include, Next: Int, Prev: Incbin, Up: Pseudo Ops + +7.62 `.include "FILE"' +====================== + +This directive provides a way to include supporting files at specified +points in your source program. The code from FILE is assembled as if +it followed the point of the `.include'; when the end of the included +file is reached, assembly of the original file continues. You can +control the search paths used with the `-I' command-line option (*note +Command-Line Options: Invoking.). Quotation marks are required around +FILE. + + +File: as.info, Node: Int, Next: Internal, Prev: Include, Up: Pseudo Ops + +7.63 `.int EXPRESSIONS' +======================= + +Expect zero or more EXPRESSIONS, of any section, separated by commas. +For each expression, emit a number that, at run time, is the value of +that expression. The byte order and bit size of the number depends on +what kind of target the assembly is for. + + +File: as.info, Node: Internal, Next: Irp, Prev: Int, Up: Pseudo Ops + +7.64 `.internal NAMES' +====================== + +This is one of the ELF visibility directives. The other two are +`.hidden' (*note `.hidden': Hidden.) and `.protected' (*note +`.protected': Protected.). + + This directive overrides the named symbols default visibility (which +is set by their binding: local, global or weak). The directive sets +the visibility to `internal' which means that the symbols are +considered to be `hidden' (i.e., not visible to other components), and +that some extra, processor specific processing must also be performed +upon the symbols as well. + + +File: as.info, Node: Irp, Next: Irpc, Prev: Internal, Up: Pseudo Ops + +7.65 `.irp SYMBOL,VALUES'... +============================ + +Evaluate a sequence of statements assigning different values to SYMBOL. +The sequence of statements starts at the `.irp' directive, and is +terminated by an `.endr' directive. For each VALUE, SYMBOL is set to +VALUE, and the sequence of statements is assembled. If no VALUE is +listed, the sequence of statements is assembled once, with SYMBOL set +to the null string. To refer to SYMBOL within the sequence of +statements, use \SYMBOL. + + For example, assembling + + .irp param,1,2,3 + move d\param,sp@- + .endr + + is equivalent to assembling + + move d1,sp@- + move d2,sp@- + move d3,sp@- + + For some caveats with the spelling of SYMBOL, see also *Note Macro::. + + +File: as.info, Node: Irpc, Next: Lcomm, Prev: Irp, Up: Pseudo Ops + +7.66 `.irpc SYMBOL,VALUES'... +============================= + +Evaluate a sequence of statements assigning different values to SYMBOL. +The sequence of statements starts at the `.irpc' directive, and is +terminated by an `.endr' directive. For each character in VALUE, +SYMBOL is set to the character, and the sequence of statements is +assembled. If no VALUE is listed, the sequence of statements is +assembled once, with SYMBOL set to the null string. To refer to SYMBOL +within the sequence of statements, use \SYMBOL. + + For example, assembling + + .irpc param,123 + move d\param,sp@- + .endr + + is equivalent to assembling + + move d1,sp@- + move d2,sp@- + move d3,sp@- + + For some caveats with the spelling of SYMBOL, see also the discussion +at *Note Macro::. + + +File: as.info, Node: Lcomm, Next: Lflags, Prev: Irpc, Up: Pseudo Ops + +7.67 `.lcomm SYMBOL , LENGTH' +============================= + +Reserve LENGTH (an absolute expression) bytes for a local common +denoted by SYMBOL. The section and value of SYMBOL are those of the +new local common. The addresses are allocated in the bss section, so +that at run-time the bytes start off zeroed. SYMBOL is not declared +global (*note `.global': Global.), so is normally not visible to `ld'. + + Some targets permit a third argument to be used with `.lcomm'. This +argument specifies the desired alignment of the symbol in the bss +section. + + The syntax for `.lcomm' differs slightly on the HPPA. The syntax is +`SYMBOL .lcomm, LENGTH'; SYMBOL is optional. + + +File: as.info, Node: Lflags, Next: Line, Prev: Lcomm, Up: Pseudo Ops + +7.68 `.lflags' +============== + +`as' accepts this directive, for compatibility with other assemblers, +but ignores it. + + +File: as.info, Node: Line, Next: Linkonce, Prev: Lflags, Up: Pseudo Ops + +7.69 `.line LINE-NUMBER' +======================== + +Change the logical line number. LINE-NUMBER must be an absolute +expression. The next line has that logical line number. Therefore any +other statements on the current line (after a statement separator +character) are reported as on logical line number LINE-NUMBER - 1. One +day `as' will no longer support this directive: it is recognized only +for compatibility with existing assembler programs. + +Even though this is a directive associated with the `a.out' or `b.out' +object-code formats, `as' still recognizes it when producing COFF +output, and treats `.line' as though it were the COFF `.ln' _if_ it is +found outside a `.def'/`.endef' pair. + + Inside a `.def', `.line' is, instead, one of the directives used by +compilers to generate auxiliary symbol information for debugging. + + +File: as.info, Node: Linkonce, Next: List, Prev: Line, Up: Pseudo Ops + +7.70 `.linkonce [TYPE]' +======================= + +Mark the current section so that the linker only includes a single copy +of it. This may be used to include the same section in several +different object files, but ensure that the linker will only include it +once in the final output file. The `.linkonce' pseudo-op must be used +for each instance of the section. Duplicate sections are detected +based on the section name, so it should be unique. + + This directive is only supported by a few object file formats; as of +this writing, the only object file format which supports it is the +Portable Executable format used on Windows NT. + + The TYPE argument is optional. If specified, it must be one of the +following strings. For example: + .linkonce same_size + Not all types may be supported on all object file formats. + +`discard' + Silently discard duplicate sections. This is the default. + +`one_only' + Warn if there are duplicate sections, but still keep only one copy. + +`same_size' + Warn if any of the duplicates have different sizes. + +`same_contents' + Warn if any of the duplicates do not have exactly the same + contents. + + +File: as.info, Node: List, Next: Ln, Prev: Linkonce, Up: Pseudo Ops + +7.71 `.list' +============ + +Control (in conjunction with the `.nolist' directive) whether or not +assembly listings are generated. These two directives maintain an +internal counter (which is zero initially). `.list' increments the +counter, and `.nolist' decrements it. Assembly listings are generated +whenever the counter is greater than zero. + + By default, listings are disabled. When you enable them (with the +`-a' command line option; *note Command-Line Options: Invoking.), the +initial value of the listing counter is one. + + +File: as.info, Node: Ln, Next: Loc, Prev: List, Up: Pseudo Ops + +7.72 `.ln LINE-NUMBER' +====================== + +`.ln' is a synonym for `.line'. + + +File: as.info, Node: Loc, Next: Loc_mark_labels, Prev: Ln, Up: Pseudo Ops + +7.73 `.loc FILENO LINENO [COLUMN] [OPTIONS]' +============================================ + +When emitting DWARF2 line number information, the `.loc' directive will +add a row to the `.debug_line' line number matrix corresponding to the +immediately following assembly instruction. The FILENO, LINENO, and +optional COLUMN arguments will be applied to the `.debug_line' state +machine before the row is added. + + The OPTIONS are a sequence of the following tokens in any order: + +`basic_block' + This option will set the `basic_block' register in the + `.debug_line' state machine to `true'. + +`prologue_end' + This option will set the `prologue_end' register in the + `.debug_line' state machine to `true'. + +`epilogue_begin' + This option will set the `epilogue_begin' register in the + `.debug_line' state machine to `true'. + +`is_stmt VALUE' + This option will set the `is_stmt' register in the `.debug_line' + state machine to `value', which must be either 0 or 1. + +`isa VALUE' + This directive will set the `isa' register in the `.debug_line' + state machine to VALUE, which must be an unsigned integer. + +`discriminator VALUE' + This directive will set the `discriminator' register in the + `.debug_line' state machine to VALUE, which must be an unsigned + integer. + + + +File: as.info, Node: Loc_mark_labels, Next: Local, Prev: Loc, Up: Pseudo Ops + +7.74 `.loc_mark_labels ENABLE' +============================== + +When emitting DWARF2 line number information, the `.loc_mark_labels' +directive makes the assembler emit an entry to the `.debug_line' line +number matrix with the `basic_block' register in the state machine set +whenever a code label is seen. The ENABLE argument should be either 1 +or 0, to enable or disable this function respectively. + + +File: as.info, Node: Local, Next: Long, Prev: Loc_mark_labels, Up: Pseudo Ops + +7.75 `.local NAMES' +=================== + +This directive, which is available for ELF targets, marks each symbol in +the comma-separated list of `names' as a local symbol so that it will +not be externally visible. If the symbols do not already exist, they +will be created. + + For targets where the `.lcomm' directive (*note Lcomm::) does not +accept an alignment argument, which is the case for most ELF targets, +the `.local' directive can be used in combination with `.comm' (*note +Comm::) to define aligned local common data. + + +File: as.info, Node: Long, Next: Macro, Prev: Local, Up: Pseudo Ops + +7.76 `.long EXPRESSIONS' +======================== + +`.long' is the same as `.int'. *Note `.int': Int. + + +File: as.info, Node: Macro, Next: MRI, Prev: Long, Up: Pseudo Ops + +7.77 `.macro' +============= + +The commands `.macro' and `.endm' allow you to define macros that +generate assembly output. For example, this definition specifies a +macro `sum' that puts a sequence of numbers into memory: + + .macro sum from=0, to=5 + .long \from + .if \to-\from + sum "(\from+1)",\to + .endif + .endm + +With that definition, `SUM 0,5' is equivalent to this assembly input: + + .long 0 + .long 1 + .long 2 + .long 3 + .long 4 + .long 5 + +`.macro MACNAME' +`.macro MACNAME MACARGS ...' + Begin the definition of a macro called MACNAME. If your macro + definition requires arguments, specify their names after the macro + name, separated by commas or spaces. You can qualify the macro + argument to indicate whether all invocations must specify a + non-blank value (through `:`req''), or whether it takes all of the + remaining arguments (through `:`vararg''). You can supply a + default value for any macro argument by following the name with + `=DEFLT'. You cannot define two macros with the same MACNAME + unless it has been subject to the `.purgem' directive (*note + Purgem::) between the two definitions. For example, these are all + valid `.macro' statements: + + `.macro comm' + Begin the definition of a macro called `comm', which takes no + arguments. + + `.macro plus1 p, p1' + `.macro plus1 p p1' + Either statement begins the definition of a macro called + `plus1', which takes two arguments; within the macro + definition, write `\p' or `\p1' to evaluate the arguments. + + `.macro reserve_str p1=0 p2' + Begin the definition of a macro called `reserve_str', with two + arguments. The first argument has a default value, but not + the second. After the definition is complete, you can call + the macro either as `reserve_str A,B' (with `\p1' evaluating + to A and `\p2' evaluating to B), or as `reserve_str ,B' (with + `\p1' evaluating as the default, in this case `0', and `\p2' + evaluating to B). + + `.macro m p1:req, p2=0, p3:vararg' + Begin the definition of a macro called `m', with at least + three arguments. The first argument must always have a value + specified, but not the second, which instead has a default + value. The third formal will get assigned all remaining + arguments specified at invocation time. + + When you call a macro, you can specify the argument values + either by position, or by keyword. For example, `sum 9,17' + is equivalent to `sum to=17, from=9'. + + + Note that since each of the MACARGS can be an identifier exactly + as any other one permitted by the target architecture, there may be + occasional problems if the target hand-crafts special meanings to + certain characters when they occur in a special position. For + example, if the colon (`:') is generally permitted to be part of a + symbol name, but the architecture specific code special-cases it + when occurring as the final character of a symbol (to denote a + label), then the macro parameter replacement code will have no way + of knowing that and consider the whole construct (including the + colon) an identifier, and check only this identifier for being the + subject to parameter substitution. So for example this macro + definition: + + .macro label l + \l: + .endm + + might not work as expected. Invoking `label foo' might not create + a label called `foo' but instead just insert the text `\l:' into + the assembler source, probably generating an error about an + unrecognised identifier. + + Similarly problems might occur with the period character (`.') + which is often allowed inside opcode names (and hence identifier + names). So for example constructing a macro to build an opcode + from a base name and a length specifier like this: + + .macro opcode base length + \base.\length + .endm + + and invoking it as `opcode store l' will not create a `store.l' + instruction but instead generate some kind of error as the + assembler tries to interpret the text `\base.\length'. + + There are several possible ways around this problem: + + `Insert white space' + If it is possible to use white space characters then this is + the simplest solution. eg: + + .macro label l + \l : + .endm + + `Use `\()'' + The string `\()' can be used to separate the end of a macro + argument from the following text. eg: + + .macro opcode base length + \base\().\length + .endm + + `Use the alternate macro syntax mode' + In the alternative macro syntax mode the ampersand character + (`&') can be used as a separator. eg: + + .altmacro + .macro label l + l&: + .endm + + Note: this problem of correctly identifying string parameters to + pseudo ops also applies to the identifiers used in `.irp' (*note + Irp::) and `.irpc' (*note Irpc::) as well. + +`.endm' + Mark the end of a macro definition. + +`.exitm' + Exit early from the current macro definition. + +`\@' + `as' maintains a counter of how many macros it has executed in + this pseudo-variable; you can copy that number to your output with + `\@', but _only within a macro definition_. + +`LOCAL NAME [ , ... ]' + _Warning: `LOCAL' is only available if you select "alternate macro + syntax" with `--alternate' or `.altmacro'._ *Note `.altmacro': + Altmacro. + + +File: as.info, Node: MRI, Next: Noaltmacro, Prev: Macro, Up: Pseudo Ops + +7.78 `.mri VAL' +=============== + +If VAL is non-zero, this tells `as' to enter MRI mode. If VAL is zero, +this tells `as' to exit MRI mode. This change affects code assembled +until the next `.mri' directive, or until the end of the file. *Note +MRI mode: M. + + +File: as.info, Node: Noaltmacro, Next: Nolist, Prev: MRI, Up: Pseudo Ops + +7.79 `.noaltmacro' +================== + +Disable alternate macro mode. *Note Altmacro::. + + +File: as.info, Node: Nolist, Next: Octa, Prev: Noaltmacro, Up: Pseudo Ops + +7.80 `.nolist' +============== + +Control (in conjunction with the `.list' directive) whether or not +assembly listings are generated. These two directives maintain an +internal counter (which is zero initially). `.list' increments the +counter, and `.nolist' decrements it. Assembly listings are generated +whenever the counter is greater than zero. + + +File: as.info, Node: Octa, Next: Org, Prev: Nolist, Up: Pseudo Ops + +7.81 `.octa BIGNUMS' +==================== + +This directive expects zero or more bignums, separated by commas. For +each bignum, it emits a 16-byte integer. + + The term "octa" comes from contexts in which a "word" is two bytes; +hence _octa_-word for 16 bytes. + + +File: as.info, Node: Org, Next: P2align, Prev: Octa, Up: Pseudo Ops + +7.82 `.org NEW-LC , FILL' +========================= + +Advance the location counter of the current section to NEW-LC. NEW-LC +is either an absolute expression or an expression with the same section +as the current subsection. That is, you can't use `.org' to cross +sections: if NEW-LC has the wrong section, the `.org' directive is +ignored. To be compatible with former assemblers, if the section of +NEW-LC is absolute, `as' issues a warning, then pretends the section of +NEW-LC is the same as the current subsection. + + `.org' may only increase the location counter, or leave it +unchanged; you cannot use `.org' to move the location counter backwards. + + Because `as' tries to assemble programs in one pass, NEW-LC may not +be undefined. If you really detest this restriction we eagerly await a +chance to share your improved assembler. + + Beware that the origin is relative to the start of the section, not +to the start of the subsection. This is compatible with other people's +assemblers. + + When the location counter (of the current subsection) is advanced, +the intervening bytes are filled with FILL which should be an absolute +expression. If the comma and FILL are omitted, FILL defaults to zero. + + +File: as.info, Node: P2align, Next: PopSection, Prev: Org, Up: Pseudo Ops + +7.83 `.p2align[wl] ABS-EXPR, ABS-EXPR, ABS-EXPR' +================================================ + +Pad the location counter (in the current subsection) to a particular +storage boundary. The first expression (which must be absolute) is the +number of low-order zero bits the location counter must have after +advancement. For example `.p2align 3' advances the location counter +until it a multiple of 8. If the location counter is already a +multiple of 8, no change is needed. + + The second expression (also absolute) gives the fill value to be +stored in the padding bytes. It (and the comma) may be omitted. If it +is omitted, the padding bytes are normally zero. However, on some +systems, if the section is marked as containing code and the fill value +is omitted, the space is filled with no-op instructions. + + The third expression is also absolute, and is also optional. If it +is present, it is the maximum number of bytes that should be skipped by +this alignment directive. If doing the alignment would require +skipping more bytes than the specified maximum, then the alignment is +not done at all. You can omit the fill value (the second argument) +entirely by simply using two commas after the required alignment; this +can be useful if you want the alignment to be filled with no-op +instructions when appropriate. + + The `.p2alignw' and `.p2alignl' directives are variants of the +`.p2align' directive. The `.p2alignw' directive treats the fill +pattern as a two byte word value. The `.p2alignl' directives treats the +fill pattern as a four byte longword value. For example, `.p2alignw +2,0x368d' will align to a multiple of 4. If it skips two bytes, they +will be filled in with the value 0x368d (the exact placement of the +bytes depends upon the endianness of the processor). If it skips 1 or +3 bytes, the fill value is undefined. + + +File: as.info, Node: PopSection, Next: Previous, Prev: P2align, Up: Pseudo Ops + +7.84 `.popsection' +================== + +This is one of the ELF section stack manipulation directives. The +others are `.section' (*note Section::), `.subsection' (*note +SubSection::), `.pushsection' (*note PushSection::), and `.previous' +(*note Previous::). + + This directive replaces the current section (and subsection) with +the top section (and subsection) on the section stack. This section is +popped off the stack. + + +File: as.info, Node: Previous, Next: Print, Prev: PopSection, Up: Pseudo Ops + +7.85 `.previous' +================ + +This is one of the ELF section stack manipulation directives. The +others are `.section' (*note Section::), `.subsection' (*note +SubSection::), `.pushsection' (*note PushSection::), and `.popsection' +(*note PopSection::). + + This directive swaps the current section (and subsection) with most +recently referenced section/subsection pair prior to this one. Multiple +`.previous' directives in a row will flip between two sections (and +their subsections). For example: + + .section A + .subsection 1 + .word 0x1234 + .subsection 2 + .word 0x5678 + .previous + .word 0x9abc + + Will place 0x1234 and 0x9abc into subsection 1 and 0x5678 into +subsection 2 of section A. Whilst: + + .section A + .subsection 1 + # Now in section A subsection 1 + .word 0x1234 + .section B + .subsection 0 + # Now in section B subsection 0 + .word 0x5678 + .subsection 1 + # Now in section B subsection 1 + .word 0x9abc + .previous + # Now in section B subsection 0 + .word 0xdef0 + + Will place 0x1234 into section A, 0x5678 and 0xdef0 into subsection +0 of section B and 0x9abc into subsection 1 of section B. + + In terms of the section stack, this directive swaps the current +section with the top section on the section stack. + + +File: as.info, Node: Print, Next: Protected, Prev: Previous, Up: Pseudo Ops + +7.86 `.print STRING' +==================== + +`as' will print STRING on the standard output during assembly. You +must put STRING in double quotes. + + +File: as.info, Node: Protected, Next: Psize, Prev: Print, Up: Pseudo Ops + +7.87 `.protected NAMES' +======================= + +This is one of the ELF visibility directives. The other two are +`.hidden' (*note Hidden::) and `.internal' (*note Internal::). + + This directive overrides the named symbols default visibility (which +is set by their binding: local, global or weak). The directive sets +the visibility to `protected' which means that any references to the +symbols from within the components that defines them must be resolved +to the definition in that component, even if a definition in another +component would normally preempt this. + + +File: as.info, Node: Psize, Next: Purgem, Prev: Protected, Up: Pseudo Ops + +7.88 `.psize LINES , COLUMNS' +============================= + +Use this directive to declare the number of lines--and, optionally, the +number of columns--to use for each page, when generating listings. + + If you do not use `.psize', listings use a default line-count of 60. +You may omit the comma and COLUMNS specification; the default width is +200 columns. + + `as' generates formfeeds whenever the specified number of lines is +exceeded (or whenever you explicitly request one, using `.eject'). + + If you specify LINES as `0', no formfeeds are generated save those +explicitly specified with `.eject'. + + +File: as.info, Node: Purgem, Next: PushSection, Prev: Psize, Up: Pseudo Ops + +7.89 `.purgem NAME' +=================== + +Undefine the macro NAME, so that later uses of the string will not be +expanded. *Note Macro::. + + +File: as.info, Node: PushSection, Next: Quad, Prev: Purgem, Up: Pseudo Ops + +7.90 `.pushsection NAME [, SUBSECTION] [, "FLAGS"[, @TYPE[,ARGUMENTS]]]' +======================================================================== + +This is one of the ELF section stack manipulation directives. The +others are `.section' (*note Section::), `.subsection' (*note +SubSection::), `.popsection' (*note PopSection::), and `.previous' +(*note Previous::). + + This directive pushes the current section (and subsection) onto the +top of the section stack, and then replaces the current section and +subsection with `name' and `subsection'. The optional `flags', `type' +and `arguments' are treated the same as in the `.section' (*note +Section::) directive. + + +File: as.info, Node: Quad, Next: Reloc, Prev: PushSection, Up: Pseudo Ops + +7.91 `.quad BIGNUMS' +==================== + +`.quad' expects zero or more bignums, separated by commas. For each +bignum, it emits an 8-byte integer. If the bignum won't fit in 8 +bytes, it prints a warning message; and just takes the lowest order 8 +bytes of the bignum. + + The term "quad" comes from contexts in which a "word" is two bytes; +hence _quad_-word for 8 bytes. + + +File: as.info, Node: Reloc, Next: Rept, Prev: Quad, Up: Pseudo Ops + +7.92 `.reloc OFFSET, RELOC_NAME[, EXPRESSION]' +============================================== + +Generate a relocation at OFFSET of type RELOC_NAME with value +EXPRESSION. If OFFSET is a number, the relocation is generated in the +current section. If OFFSET is an expression that resolves to a symbol +plus offset, the relocation is generated in the given symbol's section. +EXPRESSION, if present, must resolve to a symbol plus addend or to an +absolute value, but note that not all targets support an addend. e.g. +ELF REL targets such as i386 store an addend in the section contents +rather than in the relocation. This low level interface does not +support addends stored in the section. + + +File: as.info, Node: Rept, Next: Sbttl, Prev: Reloc, Up: Pseudo Ops + +7.93 `.rept COUNT' +================== + +Repeat the sequence of lines between the `.rept' directive and the next +`.endr' directive COUNT times. + + For example, assembling + + .rept 3 + .long 0 + .endr + + is equivalent to assembling + + .long 0 + .long 0 + .long 0 + + +File: as.info, Node: Sbttl, Next: Scl, Prev: Rept, Up: Pseudo Ops + +7.94 `.sbttl "SUBHEADING"' +========================== + +Use SUBHEADING as the title (third line, immediately after the title +line) when generating assembly listings. + + This directive affects subsequent pages, as well as the current page +if it appears within ten lines of the top of a page. + + +File: as.info, Node: Scl, Next: Section, Prev: Sbttl, Up: Pseudo Ops + +7.95 `.scl CLASS' +================= + +Set the storage-class value for a symbol. This directive may only be +used inside a `.def'/`.endef' pair. Storage class may flag whether a +symbol is static or external, or it may record further symbolic +debugging information. + + +File: as.info, Node: Section, Next: Set, Prev: Scl, Up: Pseudo Ops + +7.96 `.section NAME' +==================== + +Use the `.section' directive to assemble the following code into a +section named NAME. + + This directive is only supported for targets that actually support +arbitrarily named sections; on `a.out' targets, for example, it is not +accepted, even with a standard `a.out' section name. + +COFF Version +------------ + + For COFF targets, the `.section' directive is used in one of the +following ways: + + .section NAME[, "FLAGS"] + .section NAME[, SUBSECTION] + + If the optional argument is quoted, it is taken as flags to use for +the section. Each flag is a single character. The following flags are +recognized: +`b' + bss section (uninitialized data) + +`n' + section is not loaded + +`w' + writable section + +`d' + data section + +`r' + read-only section + +`x' + executable section + +`s' + shared section (meaningful for PE targets) + +`a' + ignored. (For compatibility with the ELF version) + +`y' + section is not readable (meaningful for PE targets) + +`0-9' + single-digit power-of-two section alignment (GNU extension) + + If no flags are specified, the default flags depend upon the section +name. If the section name is not recognized, the default will be for +the section to be loaded and writable. Note the `n' and `w' flags +remove attributes from the section, rather than adding them, so if they +are used on their own it will be as if no flags had been specified at +all. + + If the optional argument to the `.section' directive is not quoted, +it is taken as a subsection number (*note Sub-Sections::). + +ELF Version +----------- + + This is one of the ELF section stack manipulation directives. The +others are `.subsection' (*note SubSection::), `.pushsection' (*note +PushSection::), `.popsection' (*note PopSection::), and `.previous' +(*note Previous::). + + For ELF targets, the `.section' directive is used like this: + + .section NAME [, "FLAGS"[, @TYPE[,FLAG_SPECIFIC_ARGUMENTS]]] + + The optional FLAGS argument is a quoted string which may contain any +combination of the following characters: +`a' + section is allocatable + +`w' + section is writable + +`x' + section is executable + +`M' + section is mergeable + +`S' + section contains zero terminated strings + +`G' + section is a member of a section group + +`T' + section is used for thread-local-storage + + The optional TYPE argument may contain one of the following +constants: +`@progbits' + section contains data + +`@nobits' + section does not contain data (i.e., section only occupies space) + +`@note' + section contains data which is used by things other than the + program + +`@init_array' + section contains an array of pointers to init functions + +`@fini_array' + section contains an array of pointers to finish functions + +`@preinit_array' + section contains an array of pointers to pre-init functions + + Many targets only support the first three section types. + + Note on targets where the `@' character is the start of a comment (eg +ARM) then another character is used instead. For example the ARM port +uses the `%' character. + + If FLAGS contains the `M' symbol then the TYPE argument must be +specified as well as an extra argument--ENTSIZE--like this: + + .section NAME , "FLAGS"M, @TYPE, ENTSIZE + + Sections with the `M' flag but not `S' flag must contain fixed size +constants, each ENTSIZE octets long. Sections with both `M' and `S' +must contain zero terminated strings where each character is ENTSIZE +bytes long. The linker may remove duplicates within sections with the +same name, same entity size and same flags. ENTSIZE must be an +absolute expression. For sections with both `M' and `S', a string +which is a suffix of a larger string is considered a duplicate. Thus +`"def"' will be merged with `"abcdef"'; A reference to the first +`"def"' will be changed to a reference to `"abcdef"+3'. + + If FLAGS contains the `G' symbol then the TYPE argument must be +present along with an additional field like this: + + .section NAME , "FLAGS"G, @TYPE, GROUPNAME[, LINKAGE] + + The GROUPNAME field specifies the name of the section group to which +this particular section belongs. The optional linkage field can +contain: +`comdat' + indicates that only one copy of this section should be retained + +`.gnu.linkonce' + an alias for comdat + + Note: if both the M and G flags are present then the fields for the +Merge flag should come first, like this: + + .section NAME , "FLAGS"MG, @TYPE, ENTSIZE, GROUPNAME[, LINKAGE] + + If no flags are specified, the default flags depend upon the section +name. If the section name is not recognized, the default will be for +the section to have none of the above flags: it will not be allocated +in memory, nor writable, nor executable. The section will contain data. + + For ELF targets, the assembler supports another type of `.section' +directive for compatibility with the Solaris assembler: + + .section "NAME"[, FLAGS...] + + Note that the section name is quoted. There may be a sequence of +comma separated flags: +`#alloc' + section is allocatable + +`#write' + section is writable + +`#execinstr' + section is executable + +`#tls' + section is used for thread local storage + + This directive replaces the current section and subsection. See the +contents of the gas testsuite directory `gas/testsuite/gas/elf' for +some examples of how this directive and the other section stack +directives work. + + +File: as.info, Node: Set, Next: Short, Prev: Section, Up: Pseudo Ops + +7.97 `.set SYMBOL, EXPRESSION' +============================== + +Set the value of SYMBOL to EXPRESSION. This changes SYMBOL's value and +type to conform to EXPRESSION. If SYMBOL was flagged as external, it +remains flagged (*note Symbol Attributes::). + + You may `.set' a symbol many times in the same assembly. + + If you `.set' a global symbol, the value stored in the object file +is the last value stored into it. + + The syntax for `set' on the HPPA is `SYMBOL .set EXPRESSION'. + + On Z80 `set' is a real instruction, use `SYMBOL defl EXPRESSION' +instead. + + +File: as.info, Node: Short, Next: Single, Prev: Set, Up: Pseudo Ops + +7.98 `.short EXPRESSIONS' +========================= + +`.short' is normally the same as `.word'. *Note `.word': Word. + + In some configurations, however, `.short' and `.word' generate +numbers of different lengths. *Note Machine Dependencies::. + + +File: as.info, Node: Single, Next: Size, Prev: Short, Up: Pseudo Ops + +7.99 `.single FLONUMS' +====================== + +This directive assembles zero or more flonums, separated by commas. It +has the same effect as `.float'. The exact kind of floating point +numbers emitted depends on how `as' is configured. *Note Machine +Dependencies::. + + +File: as.info, Node: Size, Next: Skip, Prev: Single, Up: Pseudo Ops + +7.100 `.size' +============= + +This directive is used to set the size associated with a symbol. + +COFF Version +------------ + + For COFF targets, the `.size' directive is only permitted inside +`.def'/`.endef' pairs. It is used like this: + + .size EXPRESSION + +ELF Version +----------- + + For ELF targets, the `.size' directive is used like this: + + .size NAME , EXPRESSION + + This directive sets the size associated with a symbol NAME. The +size in bytes is computed from EXPRESSION which can make use of label +arithmetic. This directive is typically used to set the size of +function symbols. + + +File: as.info, Node: Skip, Next: Sleb128, Prev: Size, Up: Pseudo Ops + +7.101 `.skip SIZE , FILL' +========================= + +This directive emits SIZE bytes, each of value FILL. Both SIZE and +FILL are absolute expressions. If the comma and FILL are omitted, FILL +is assumed to be zero. This is the same as `.space'. + + +File: as.info, Node: Sleb128, Next: Space, Prev: Skip, Up: Pseudo Ops + +7.102 `.sleb128 EXPRESSIONS' +============================ + +SLEB128 stands for "signed little endian base 128." This is a compact, +variable length representation of numbers used by the DWARF symbolic +debugging format. *Note `.uleb128': Uleb128. + + +File: as.info, Node: Space, Next: Stab, Prev: Sleb128, Up: Pseudo Ops + +7.103 `.space SIZE , FILL' +========================== + +This directive emits SIZE bytes, each of value FILL. Both SIZE and +FILL are absolute expressions. If the comma and FILL are omitted, FILL +is assumed to be zero. This is the same as `.skip'. + + _Warning:_ `.space' has a completely different meaning for HPPA + targets; use `.block' as a substitute. See `HP9000 Series 800 + Assembly Language Reference Manual' (HP 92432-90001) for the + meaning of the `.space' directive. *Note HPPA Assembler + Directives: HPPA Directives, for a summary. + + +File: as.info, Node: Stab, Next: String, Prev: Space, Up: Pseudo Ops + +7.104 `.stabd, .stabn, .stabs' +============================== + +There are three directives that begin `.stab'. All emit symbols (*note +Symbols::), for use by symbolic debuggers. The symbols are not entered +in the `as' hash table: they cannot be referenced elsewhere in the +source file. Up to five fields are required: + +STRING + This is the symbol's name. It may contain any character except + `\000', so is more general than ordinary symbol names. Some + debuggers used to code arbitrarily complex structures into symbol + names using this field. + +TYPE + An absolute expression. The symbol's type is set to the low 8 + bits of this expression. Any bit pattern is permitted, but `ld' + and debuggers choke on silly bit patterns. + +OTHER + An absolute expression. The symbol's "other" attribute is set to + the low 8 bits of this expression. + +DESC + An absolute expression. The symbol's descriptor is set to the low + 16 bits of this expression. + +VALUE + An absolute expression which becomes the symbol's value. + + If a warning is detected while reading a `.stabd', `.stabn', or +`.stabs' statement, the symbol has probably already been created; you +get a half-formed symbol in your object file. This is compatible with +earlier assemblers! + +`.stabd TYPE , OTHER , DESC' + The "name" of the symbol generated is not even an empty string. + It is a null pointer, for compatibility. Older assemblers used a + null pointer so they didn't waste space in object files with empty + strings. + + The symbol's value is set to the location counter, relocatably. + When your program is linked, the value of this symbol is the + address of the location counter when the `.stabd' was assembled. + +`.stabn TYPE , OTHER , DESC , VALUE' + The name of the symbol is set to the empty string `""'. + +`.stabs STRING , TYPE , OTHER , DESC , VALUE' + All five fields are specified. + + +File: as.info, Node: String, Next: Struct, Prev: Stab, Up: Pseudo Ops + +7.105 `.string' "STR", `.string8' "STR", `.string16' +==================================================== + +"STR", `.string32' "STR", `.string64' "STR" + + Copy the characters in STR to the object file. You may specify more +than one string to copy, separated by commas. Unless otherwise +specified for a particular machine, the assembler marks the end of each +string with a 0 byte. You can use any of the escape sequences +described in *Note Strings: Strings. + + The variants `string16', `string32' and `string64' differ from the +`string' pseudo opcode in that each 8-bit character from STR is copied +and expanded to 16, 32 or 64 bits respectively. The expanded characters +are stored in target endianness byte order. + + Example: + .string32 "BYE" + expands to: + .string "B\0\0\0Y\0\0\0E\0\0\0" /* On little endian targets. */ + .string "\0\0\0B\0\0\0Y\0\0\0E" /* On big endian targets. */ + + +File: as.info, Node: Struct, Next: SubSection, Prev: String, Up: Pseudo Ops + +7.106 `.struct EXPRESSION' +========================== + +Switch to the absolute section, and set the section offset to +EXPRESSION, which must be an absolute expression. You might use this +as follows: + .struct 0 + field1: + .struct field1 + 4 + field2: + .struct field2 + 4 + field3: + This would define the symbol `field1' to have the value 0, the symbol +`field2' to have the value 4, and the symbol `field3' to have the value +8. Assembly would be left in the absolute section, and you would need +to use a `.section' directive of some sort to change to some other +section before further assembly. + + +File: as.info, Node: SubSection, Next: Symver, Prev: Struct, Up: Pseudo Ops + +7.107 `.subsection NAME' +======================== + +This is one of the ELF section stack manipulation directives. The +others are `.section' (*note Section::), `.pushsection' (*note +PushSection::), `.popsection' (*note PopSection::), and `.previous' +(*note Previous::). + + This directive replaces the current subsection with `name'. The +current section is not changed. The replaced subsection is put onto +the section stack in place of the then current top of stack subsection. + + +File: as.info, Node: Symver, Next: Tag, Prev: SubSection, Up: Pseudo Ops + +7.108 `.symver' +=============== + +Use the `.symver' directive to bind symbols to specific version nodes +within a source file. This is only supported on ELF platforms, and is +typically used when assembling files to be linked into a shared library. +There are cases where it may make sense to use this in objects to be +bound into an application itself so as to override a versioned symbol +from a shared library. + + For ELF targets, the `.symver' directive can be used like this: + .symver NAME, NAME2@NODENAME + If the symbol NAME is defined within the file being assembled, the +`.symver' directive effectively creates a symbol alias with the name +NAME2@NODENAME, and in fact the main reason that we just don't try and +create a regular alias is that the @ character isn't permitted in +symbol names. The NAME2 part of the name is the actual name of the +symbol by which it will be externally referenced. The name NAME itself +is merely a name of convenience that is used so that it is possible to +have definitions for multiple versions of a function within a single +source file, and so that the compiler can unambiguously know which +version of a function is being mentioned. The NODENAME portion of the +alias should be the name of a node specified in the version script +supplied to the linker when building a shared library. If you are +attempting to override a versioned symbol from a shared library, then +NODENAME should correspond to the nodename of the symbol you are trying +to override. + + If the symbol NAME is not defined within the file being assembled, +all references to NAME will be changed to NAME2@NODENAME. If no +reference to NAME is made, NAME2@NODENAME will be removed from the +symbol table. + + Another usage of the `.symver' directive is: + .symver NAME, NAME2@@NODENAME + In this case, the symbol NAME must exist and be defined within the +file being assembled. It is similar to NAME2@NODENAME. The difference +is NAME2@@NODENAME will also be used to resolve references to NAME2 by +the linker. + + The third usage of the `.symver' directive is: + .symver NAME, NAME2@@@NODENAME + When NAME is not defined within the file being assembled, it is +treated as NAME2@NODENAME. When NAME is defined within the file being +assembled, the symbol name, NAME, will be changed to NAME2@@NODENAME. + + +File: as.info, Node: Tag, Next: Text, Prev: Symver, Up: Pseudo Ops + +7.109 `.tag STRUCTNAME' +======================= + +This directive is generated by compilers to include auxiliary debugging +information in the symbol table. It is only permitted inside +`.def'/`.endef' pairs. Tags are used to link structure definitions in +the symbol table with instances of those structures. + + +File: as.info, Node: Text, Next: Title, Prev: Tag, Up: Pseudo Ops + +7.110 `.text SUBSECTION' +======================== + +Tells `as' to assemble the following statements onto the end of the +text subsection numbered SUBSECTION, which is an absolute expression. +If SUBSECTION is omitted, subsection number zero is used. + + +File: as.info, Node: Title, Next: Type, Prev: Text, Up: Pseudo Ops + +7.111 `.title "HEADING"' +======================== + +Use HEADING as the title (second line, immediately after the source +file name and pagenumber) when generating assembly listings. + + This directive affects subsequent pages, as well as the current page +if it appears within ten lines of the top of a page. + + +File: as.info, Node: Type, Next: Uleb128, Prev: Title, Up: Pseudo Ops + +7.112 `.type' +============= + +This directive is used to set the type of a symbol. + +COFF Version +------------ + + For COFF targets, this directive is permitted only within +`.def'/`.endef' pairs. It is used like this: + + .type INT + + This records the integer INT as the type attribute of a symbol table +entry. + +ELF Version +----------- + + For ELF targets, the `.type' directive is used like this: + + .type NAME , TYPE DESCRIPTION + + This sets the type of symbol NAME to be either a function symbol or +an object symbol. There are five different syntaxes supported for the +TYPE DESCRIPTION field, in order to provide compatibility with various +other assemblers. + + Because some of the characters used in these syntaxes (such as `@' +and `#') are comment characters for some architectures, some of the +syntaxes below do not work on all architectures. The first variant +will be accepted by the GNU assembler on all architectures so that +variant should be used for maximum portability, if you do not need to +assemble your code with other assemblers. + + The syntaxes supported are: + + .type <name> STT_<TYPE_IN_UPPER_CASE> + .type <name>,#<type> + .type <name>,@<type> + .type <name>,%<type> + .type <name>,"<type>" + + The types supported are: + +`STT_FUNC' +`function' + Mark the symbol as being a function name. + +`STT_GNU_IFUNC' +`gnu_indirect_function' + Mark the symbol as an indirect function when evaluated during reloc + processing. (This is only supported on Linux targeted assemblers). + +`STT_OBJECT' +`object' + Mark the symbol as being a data object. + +`STT_TLS' +`tls_object' + Mark the symbol as being a thead-local data object. + +`STT_COMMON' +`common' + Mark the symbol as being a common data object. + +`STT_NOTYPE' +`notype' + Does not mark the symbol in any way. It is supported just for + completeness. + +`gnu_unique_object' + Marks the symbol as being a globally unique data object. The + dynamic linker will make sure that in the entire process there is + just one symbol with this name and type in use. (This is only + supported on Linux targeted assemblers). + + + Note: Some targets support extra types in addition to those listed +above. + + +File: as.info, Node: Uleb128, Next: Val, Prev: Type, Up: Pseudo Ops + +7.113 `.uleb128 EXPRESSIONS' +============================ + +ULEB128 stands for "unsigned little endian base 128." This is a +compact, variable length representation of numbers used by the DWARF +symbolic debugging format. *Note `.sleb128': Sleb128. + + +File: as.info, Node: Val, Next: Version, Prev: Uleb128, Up: Pseudo Ops + +7.114 `.val ADDR' +================= + +This directive, permitted only within `.def'/`.endef' pairs, records +the address ADDR as the value attribute of a symbol table entry. + + +File: as.info, Node: Version, Next: VTableEntry, Prev: Val, Up: Pseudo Ops + +7.115 `.version "STRING"' +========================= + +This directive creates a `.note' section and places into it an ELF +formatted note of type NT_VERSION. The note's name is set to `string'. + + +File: as.info, Node: VTableEntry, Next: VTableInherit, Prev: Version, Up: Pseudo Ops + +7.116 `.vtable_entry TABLE, OFFSET' +=================================== + +This directive finds or creates a symbol `table' and creates a +`VTABLE_ENTRY' relocation for it with an addend of `offset'. + + +File: as.info, Node: VTableInherit, Next: Warning, Prev: VTableEntry, Up: Pseudo Ops + +7.117 `.vtable_inherit CHILD, PARENT' +===================================== + +This directive finds the symbol `child' and finds or creates the symbol +`parent' and then creates a `VTABLE_INHERIT' relocation for the parent +whose addend is the value of the child symbol. As a special case the +parent name of `0' is treated as referring to the `*ABS*' section. + + +File: as.info, Node: Warning, Next: Weak, Prev: VTableInherit, Up: Pseudo Ops + +7.118 `.warning "STRING"' +========================= + +Similar to the directive `.error' (*note `.error "STRING"': Error.), +but just emits a warning. + + +File: as.info, Node: Weak, Next: Weakref, Prev: Warning, Up: Pseudo Ops + +7.119 `.weak NAMES' +=================== + +This directive sets the weak attribute on the comma separated list of +symbol `names'. If the symbols do not already exist, they will be +created. + + On COFF targets other than PE, weak symbols are a GNU extension. +This directive sets the weak attribute on the comma separated list of +symbol `names'. If the symbols do not already exist, they will be +created. + + On the PE target, weak symbols are supported natively as weak +aliases. When a weak symbol is created that is not an alias, GAS +creates an alternate symbol to hold the default value. + + +File: as.info, Node: Weakref, Next: Word, Prev: Weak, Up: Pseudo Ops + +7.120 `.weakref ALIAS, TARGET' +============================== + +This directive creates an alias to the target symbol that enables the +symbol to be referenced with weak-symbol semantics, but without +actually making it weak. If direct references or definitions of the +symbol are present, then the symbol will not be weak, but if all +references to it are through weak references, the symbol will be marked +as weak in the symbol table. + + The effect is equivalent to moving all references to the alias to a +separate assembly source file, renaming the alias to the symbol in it, +declaring the symbol as weak there, and running a reloadable link to +merge the object files resulting from the assembly of the new source +file and the old source file that had the references to the alias +removed. + + The alias itself never makes to the symbol table, and is entirely +handled within the assembler. + + +File: as.info, Node: Word, Next: Deprecated, Prev: Weakref, Up: Pseudo Ops + +7.121 `.word EXPRESSIONS' +========================= + +This directive expects zero or more EXPRESSIONS, of any section, +separated by commas. + + The size of the number emitted, and its byte order, depend on what +target computer the assembly is for. + + _Warning: Special Treatment to support Compilers_ + + Machines with a 32-bit address space, but that do less than 32-bit +addressing, require the following special treatment. If the machine of +interest to you does 32-bit addressing (or doesn't require it; *note +Machine Dependencies::), you can ignore this issue. + + In order to assemble compiler output into something that works, `as' +occasionally does strange things to `.word' directives. Directives of +the form `.word sym1-sym2' are often emitted by compilers as part of +jump tables. Therefore, when `as' assembles a directive of the form +`.word sym1-sym2', and the difference between `sym1' and `sym2' does +not fit in 16 bits, `as' creates a "secondary jump table", immediately +before the next label. This secondary jump table is preceded by a +short-jump to the first byte after the secondary table. This +short-jump prevents the flow of control from accidentally falling into +the new table. Inside the table is a long-jump to `sym2'. The +original `.word' contains `sym1' minus the address of the long-jump to +`sym2'. + + If there were several occurrences of `.word sym1-sym2' before the +secondary jump table, all of them are adjusted. If there was a `.word +sym3-sym4', that also did not fit in sixteen bits, a long-jump to +`sym4' is included in the secondary jump table, and the `.word' +directives are adjusted to contain `sym3' minus the address of the +long-jump to `sym4'; and so on, for as many entries in the original +jump table as necessary. + + +File: as.info, Node: Deprecated, Prev: Word, Up: Pseudo Ops + +7.122 Deprecated Directives +=========================== + +One day these directives won't work. They are included for +compatibility with older assemblers. +.abort + +.line + + +File: as.info, Node: Object Attributes, Next: Machine Dependencies, Prev: Pseudo Ops, Up: Top + +8 Object Attributes +******************* + +`as' assembles source files written for a specific architecture into +object files for that architecture. But not all object files are alike. +Many architectures support incompatible variations. For instance, +floating point arguments might be passed in floating point registers if +the object file requires hardware floating point support--or floating +point arguments might be passed in integer registers if the object file +supports processors with no hardware floating point unit. Or, if two +objects are built for different generations of the same architecture, +the combination may require the newer generation at run-time. + + This information is useful during and after linking. At link time, +`ld' can warn about incompatible object files. After link time, tools +like `gdb' can use it to process the linked file correctly. + + Compatibility information is recorded as a series of object +attributes. Each attribute has a "vendor", "tag", and "value". The +vendor is a string, and indicates who sets the meaning of the tag. The +tag is an integer, and indicates what property the attribute describes. +The value may be a string or an integer, and indicates how the +property affects this object. Missing attributes are the same as +attributes with a zero value or empty string value. + + Object attributes were developed as part of the ABI for the ARM +Architecture. The file format is documented in `ELF for the ARM +Architecture'. + +* Menu: + +* GNU Object Attributes:: GNU Object Attributes +* Defining New Object Attributes:: Defining New Object Attributes + + +File: as.info, Node: GNU Object Attributes, Next: Defining New Object Attributes, Up: Object Attributes + +8.1 GNU Object Attributes +========================= + +The `.gnu_attribute' directive records an object attribute with vendor +`gnu'. + + Except for `Tag_compatibility', which has both an integer and a +string for its value, GNU attributes have a string value if the tag +number is odd and an integer value if the tag number is even. The +second bit (`TAG & 2' is set for architecture-independent attributes +and clear for architecture-dependent ones. + +8.1.1 Common GNU attributes +--------------------------- + +These attributes are valid on all architectures. + +Tag_compatibility (32) + The compatibility attribute takes an integer flag value and a + vendor name. If the flag value is 0, the file is compatible with + other toolchains. If it is 1, then the file is only compatible + with the named toolchain. If it is greater than 1, the file can + only be processed by other toolchains under some private + arrangement indicated by the flag value and the vendor name. + +8.1.2 MIPS Attributes +--------------------- + +Tag_GNU_MIPS_ABI_FP (4) + The floating-point ABI used by this object file. The value will + be: + + * 0 for files not affected by the floating-point ABI. + + * 1 for files using the hardware floating-point with a standard + double-precision FPU. + + * 2 for files using the hardware floating-point ABI with a + single-precision FPU. + + * 3 for files using the software floating-point ABI. + + * 4 for files using the hardware floating-point ABI with 64-bit + wide double-precision floating-point registers and 32-bit + wide general purpose registers. + +8.1.3 PowerPC Attributes +------------------------ + +Tag_GNU_Power_ABI_FP (4) + The floating-point ABI used by this object file. The value will + be: + + * 0 for files not affected by the floating-point ABI. + + * 1 for files using double-precision hardware floating-point + ABI. + + * 2 for files using the software floating-point ABI. + + * 3 for files using single-precision hardware floating-point + ABI. + +Tag_GNU_Power_ABI_Vector (8) + The vector ABI used by this object file. The value will be: + + * 0 for files not affected by the vector ABI. + + * 1 for files using general purpose registers to pass vectors. + + * 2 for files using AltiVec registers to pass vectors. + + * 3 for files using SPE registers to pass vectors. + + +File: as.info, Node: Defining New Object Attributes, Prev: GNU Object Attributes, Up: Object Attributes + +8.2 Defining New Object Attributes +================================== + +If you want to define a new GNU object attribute, here are the places +you will need to modify. New attributes should be discussed on the +`binutils' mailing list. + + * This manual, which is the official register of attributes. + + * The header for your architecture `include/elf', to define the tag. + + * The `bfd' support file for your architecture, to merge the + attribute and issue any appropriate link warnings. + + * Test cases in `ld/testsuite' for merging and link warnings. + + * `binutils/readelf.c' to display your attribute. + + * GCC, if you want the compiler to mark the attribute automatically. + + +File: as.info, Node: Machine Dependencies, Next: Reporting Bugs, Prev: Object Attributes, Up: Top + +9 Machine Dependent Features +**************************** + +The machine instruction sets are (almost by definition) different on +each machine where `as' runs. Floating point representations vary as +well, and `as' often supports a few additional directives or +command-line options for compatibility with other assemblers on a +particular platform. Finally, some versions of `as' support special +pseudo-instructions for branch optimization. + + This chapter discusses most of these differences, though it does not +include details on any machine's instruction set. For details on that +subject, see the hardware manufacturer's manual. + +* Menu: + + +* Alpha-Dependent:: Alpha Dependent Features + +* ARC-Dependent:: ARC Dependent Features + +* ARM-Dependent:: ARM Dependent Features + +* AVR-Dependent:: AVR Dependent Features + +* Blackfin-Dependent:: Blackfin Dependent Features + +* CR16-Dependent:: CR16 Dependent Features + +* CRIS-Dependent:: CRIS Dependent Features + +* D10V-Dependent:: D10V Dependent Features + +* D30V-Dependent:: D30V Dependent Features + +* H8/300-Dependent:: Renesas H8/300 Dependent Features + +* HPPA-Dependent:: HPPA Dependent Features + +* ESA/390-Dependent:: IBM ESA/390 Dependent Features + +* i386-Dependent:: Intel 80386 and AMD x86-64 Dependent Features + +* i860-Dependent:: Intel 80860 Dependent Features + +* i960-Dependent:: Intel 80960 Dependent Features + +* IA-64-Dependent:: Intel IA-64 Dependent Features + +* IP2K-Dependent:: IP2K Dependent Features + +* LM32-Dependent:: LM32 Dependent Features + +* M32C-Dependent:: M32C Dependent Features + +* M32R-Dependent:: M32R Dependent Features + +* M68K-Dependent:: M680x0 Dependent Features + +* M68HC11-Dependent:: M68HC11 and 68HC12 Dependent Features + +* MicroBlaze-Dependent:: MICROBLAZE Dependent Features + +* MIPS-Dependent:: MIPS Dependent Features + +* MMIX-Dependent:: MMIX Dependent Features + +* MSP430-Dependent:: MSP430 Dependent Features + +* SH-Dependent:: Renesas / SuperH SH Dependent Features +* SH64-Dependent:: SuperH SH64 Dependent Features + +* PDP-11-Dependent:: PDP-11 Dependent Features + +* PJ-Dependent:: picoJava Dependent Features + +* PPC-Dependent:: PowerPC Dependent Features + +* S/390-Dependent:: IBM S/390 Dependent Features + +* SCORE-Dependent:: SCORE Dependent Features + +* Sparc-Dependent:: SPARC Dependent Features + +* TIC54X-Dependent:: TI TMS320C54x Dependent Features + +* V850-Dependent:: V850 Dependent Features + +* Xtensa-Dependent:: Xtensa Dependent Features + +* Z80-Dependent:: Z80 Dependent Features + +* Z8000-Dependent:: Z8000 Dependent Features + +* Vax-Dependent:: VAX Dependent Features + + +File: as.info, Node: Alpha-Dependent, Next: ARC-Dependent, Up: Machine Dependencies + +9.1 Alpha Dependent Features +============================ + +* Menu: + +* Alpha Notes:: Notes +* Alpha Options:: Options +* Alpha Syntax:: Syntax +* Alpha Floating Point:: Floating Point +* Alpha Directives:: Alpha Machine Directives +* Alpha Opcodes:: Opcodes + + +File: as.info, Node: Alpha Notes, Next: Alpha Options, Up: Alpha-Dependent + +9.1.1 Notes +----------- + +The documentation here is primarily for the ELF object format. `as' +also supports the ECOFF and EVAX formats, but features specific to +these formats are not yet documented. + + +File: as.info, Node: Alpha Options, Next: Alpha Syntax, Prev: Alpha Notes, Up: Alpha-Dependent + +9.1.2 Options +------------- + +`-mCPU' + This option specifies the target processor. If an attempt is made + to assemble an instruction which will not execute on the target + processor, the assembler may either expand the instruction as a + macro or issue an error message. This option is equivalent to the + `.arch' directive. + + The following processor names are recognized: `21064', `21064a', + `21066', `21068', `21164', `21164a', `21164pc', `21264', `21264a', + `21264b', `ev4', `ev5', `lca45', `ev5', `ev56', `pca56', `ev6', + `ev67', `ev68'. The special name `all' may be used to allow the + assembler to accept instructions valid for any Alpha processor. + + In order to support existing practice in OSF/1 with respect to + `.arch', and existing practice within `MILO' (the Linux ARC + bootloader), the numbered processor names (e.g. 21064) enable the + processor-specific PALcode instructions, while the + "electro-vlasic" names (e.g. `ev4') do not. + +`-mdebug' +`-no-mdebug' + Enables or disables the generation of `.mdebug' encapsulation for + stabs directives and procedure descriptors. The default is to + automatically enable `.mdebug' when the first stabs directive is + seen. + +`-relax' + This option forces all relocations to be put into the object file, + instead of saving space and resolving some relocations at assembly + time. Note that this option does not propagate all symbol + arithmetic into the object file, because not all symbol arithmetic + can be represented. However, the option can still be useful in + specific applications. + +`-replace' + +`-noreplace' + Enables or disables the optimization of procedure calls, both at + assemblage and at link time. These options are only available for + VMS targets and `-replace' is the default. See section 1.4.1 of + the OpenVMS Linker Utility Manual. + +`-g' + This option is used when the compiler generates debug information. + When `gcc' is using `mips-tfile' to generate debug information + for ECOFF, local labels must be passed through to the object file. + Otherwise this option has no effect. + +`-GSIZE' + A local common symbol larger than SIZE is placed in `.bss', while + smaller symbols are placed in `.sbss'. + +`-F' +`-32addr' + These options are ignored for backward compatibility. + + +File: as.info, Node: Alpha Syntax, Next: Alpha Floating Point, Prev: Alpha Options, Up: Alpha-Dependent + +9.1.3 Syntax +------------ + +The assembler syntax closely follow the Alpha Reference Manual; +assembler directives and general syntax closely follow the OSF/1 and +OpenVMS syntax, with a few differences for ELF. + +* Menu: + +* Alpha-Chars:: Special Characters +* Alpha-Regs:: Register Names +* Alpha-Relocs:: Relocations + + +File: as.info, Node: Alpha-Chars, Next: Alpha-Regs, Up: Alpha Syntax + +9.1.3.1 Special Characters +.......................... + +`#' is the line comment character. + + `;' can be used instead of a newline to separate statements. + + +File: as.info, Node: Alpha-Regs, Next: Alpha-Relocs, Prev: Alpha-Chars, Up: Alpha Syntax + +9.1.3.2 Register Names +...................... + +The 32 integer registers are referred to as `$N' or `$rN'. In +addition, registers 15, 28, 29, and 30 may be referred to by the +symbols `$fp', `$at', `$gp', and `$sp' respectively. + + The 32 floating-point registers are referred to as `$fN'. + + +File: as.info, Node: Alpha-Relocs, Prev: Alpha-Regs, Up: Alpha Syntax + +9.1.3.3 Relocations +................... + +Some of these relocations are available for ECOFF, but mostly only for +ELF. They are modeled after the relocation format introduced in +Digital Unix 4.0, but there are additions. + + The format is `!TAG' or `!TAG!NUMBER' where TAG is the name of the +relocation. In some cases NUMBER is used to relate specific +instructions. + + The relocation is placed at the end of the instruction like so: + + ldah $0,a($29) !gprelhigh + lda $0,a($0) !gprellow + ldq $1,b($29) !literal!100 + ldl $2,0($1) !lituse_base!100 + +`!literal' +`!literal!N' + Used with an `ldq' instruction to load the address of a symbol + from the GOT. + + A sequence number N is optional, and if present is used to pair + `lituse' relocations with this `literal' relocation. The `lituse' + relocations are used by the linker to optimize the code based on + the final location of the symbol. + + Note that these optimizations are dependent on the data flow of the + program. Therefore, if _any_ `lituse' is paired with a `literal' + relocation, then _all_ uses of the register set by the `literal' + instruction must also be marked with `lituse' relocations. This + is because the original `literal' instruction may be deleted or + transformed into another instruction. + + Also note that there may be a one-to-many relationship between + `literal' and `lituse', but not a many-to-one. That is, if there + are two code paths that load up the same address and feed the + value to a single use, then the use may not use a `lituse' + relocation. + +`!lituse_base!N' + Used with any memory format instruction (e.g. `ldl') to indicate + that the literal is used for an address load. The offset field of + the instruction must be zero. During relaxation, the code may be + altered to use a gp-relative load. + +`!lituse_jsr!N' + Used with a register branch format instruction (e.g. `jsr') to + indicate that the literal is used for a call. During relaxation, + the code may be altered to use a direct branch (e.g. `bsr'). + +`!lituse_jsrdirect!N' + Similar to `lituse_jsr', but also that this call cannot be vectored + through a PLT entry. This is useful for functions with special + calling conventions which do not allow the normal call-clobbered + registers to be clobbered. + +`!lituse_bytoff!N' + Used with a byte mask instruction (e.g. `extbl') to indicate that + only the low 3 bits of the address are relevant. During + relaxation, the code may be altered to use an immediate instead of + a register shift. + +`!lituse_addr!N' + Used with any other instruction to indicate that the original + address is in fact used, and the original `ldq' instruction may + not be altered or deleted. This is useful in conjunction with + `lituse_jsr' to test whether a weak symbol is defined. + + ldq $27,foo($29) !literal!1 + beq $27,is_undef !lituse_addr!1 + jsr $26,($27),foo !lituse_jsr!1 + +`!lituse_tlsgd!N' + Used with a register branch format instruction to indicate that the + literal is the call to `__tls_get_addr' used to compute the + address of the thread-local storage variable whose descriptor was + loaded with `!tlsgd!N'. + +`!lituse_tlsldm!N' + Used with a register branch format instruction to indicate that the + literal is the call to `__tls_get_addr' used to compute the + address of the base of the thread-local storage block for the + current module. The descriptor for the module must have been + loaded with `!tlsldm!N'. + +`!gpdisp!N' + Used with `ldah' and `lda' to load the GP from the current + address, a-la the `ldgp' macro. The source register for the + `ldah' instruction must contain the address of the `ldah' + instruction. There must be exactly one `lda' instruction paired + with the `ldah' instruction, though it may appear anywhere in the + instruction stream. The immediate operands must be zero. + + bsr $26,foo + ldah $29,0($26) !gpdisp!1 + lda $29,0($29) !gpdisp!1 + +`!gprelhigh' + Used with an `ldah' instruction to add the high 16 bits of a + 32-bit displacement from the GP. + +`!gprellow' + Used with any memory format instruction to add the low 16 bits of a + 32-bit displacement from the GP. + +`!gprel' + Used with any memory format instruction to add a 16-bit + displacement from the GP. + +`!samegp' + Used with any branch format instruction to skip the GP load at the + target address. The referenced symbol must have the same GP as the + source object file, and it must be declared to either not use `$27' + or perform a standard GP load in the first two instructions via the + `.prologue' directive. + +`!tlsgd' +`!tlsgd!N' + Used with an `lda' instruction to load the address of a TLS + descriptor for a symbol in the GOT. + + The sequence number N is optional, and if present it used to pair + the descriptor load with both the `literal' loading the address of + the `__tls_get_addr' function and the `lituse_tlsgd' marking the + call to that function. + + For proper relaxation, both the `tlsgd', `literal' and `lituse' + relocations must be in the same extended basic block. That is, + the relocation with the lowest address must be executed first at + runtime. + +`!tlsldm' +`!tlsldm!N' + Used with an `lda' instruction to load the address of a TLS + descriptor for the current module in the GOT. + + Similar in other respects to `tlsgd'. + +`!gotdtprel' + Used with an `ldq' instruction to load the offset of the TLS + symbol within its module's thread-local storage block. Also known + as the dynamic thread pointer offset or dtp-relative offset. + +`!dtprelhi' +`!dtprello' +`!dtprel' + Like `gprel' relocations except they compute dtp-relative offsets. + +`!gottprel' + Used with an `ldq' instruction to load the offset of the TLS + symbol from the thread pointer. Also known as the tp-relative + offset. + +`!tprelhi' +`!tprello' +`!tprel' + Like `gprel' relocations except they compute tp-relative offsets. + + +File: as.info, Node: Alpha Floating Point, Next: Alpha Directives, Prev: Alpha Syntax, Up: Alpha-Dependent + +9.1.4 Floating Point +-------------------- + +The Alpha family uses both IEEE and VAX floating-point numbers. + + +File: as.info, Node: Alpha Directives, Next: Alpha Opcodes, Prev: Alpha Floating Point, Up: Alpha-Dependent + +9.1.5 Alpha Assembler Directives +-------------------------------- + +`as' for the Alpha supports many additional directives for +compatibility with the native assembler. This section describes them +only briefly. + + These are the additional directives in `as' for the Alpha: + +`.arch CPU' + Specifies the target processor. This is equivalent to the `-mCPU' + command-line option. *Note Options: Alpha Options, for a list of + values for CPU. + +`.ent FUNCTION[, N]' + Mark the beginning of FUNCTION. An optional number may follow for + compatibility with the OSF/1 assembler, but is ignored. When + generating `.mdebug' information, this will create a procedure + descriptor for the function. In ELF, it will mark the symbol as a + function a-la the generic `.type' directive. + +`.end FUNCTION' + Mark the end of FUNCTION. In ELF, it will set the size of the + symbol a-la the generic `.size' directive. + +`.mask MASK, OFFSET' + Indicate which of the integer registers are saved in the current + function's stack frame. MASK is interpreted a bit mask in which + bit N set indicates that register N is saved. The registers are + saved in a block located OFFSET bytes from the "canonical frame + address" (CFA) which is the value of the stack pointer on entry to + the function. The registers are saved sequentially, except that + the return address register (normally `$26') is saved first. + + This and the other directives that describe the stack frame are + currently only used when generating `.mdebug' information. They + may in the future be used to generate DWARF2 `.debug_frame' unwind + information for hand written assembly. + +`.fmask MASK, OFFSET' + Indicate which of the floating-point registers are saved in the + current stack frame. The MASK and OFFSET parameters are + interpreted as with `.mask'. + +`.frame FRAMEREG, FRAMEOFFSET, RETREG[, ARGOFFSET]' + Describes the shape of the stack frame. The frame pointer in use + is FRAMEREG; normally this is either `$fp' or `$sp'. The frame + pointer is FRAMEOFFSET bytes below the CFA. The return address is + initially located in RETREG until it is saved as indicated in + `.mask'. For compatibility with OSF/1 an optional ARGOFFSET + parameter is accepted and ignored. It is believed to indicate the + offset from the CFA to the saved argument registers. + +`.prologue N' + Indicate that the stack frame is set up and all registers have been + spilled. The argument N indicates whether and how the function + uses the incoming "procedure vector" (the address of the called + function) in `$27'. 0 indicates that `$27' is not used; 1 + indicates that the first two instructions of the function use `$27' + to perform a load of the GP register; 2 indicates that `$27' is + used in some non-standard way and so the linker cannot elide the + load of the procedure vector during relaxation. + +`.usepv FUNCTION, WHICH' + Used to indicate the use of the `$27' register, similar to + `.prologue', but without the other semantics of needing to be + inside an open `.ent'/`.end' block. + + The WHICH argument should be either `no', indicating that `$27' is + not used, or `std', indicating that the first two instructions of + the function perform a GP load. + + One might use this directive instead of `.prologue' if you are + also using dwarf2 CFI directives. + +`.gprel32 EXPRESSION' + Computes the difference between the address in EXPRESSION and the + GP for the current object file, and stores it in 4 bytes. In + addition to being smaller than a full 8 byte address, this also + does not require a dynamic relocation when used in a shared + library. + +`.t_floating EXPRESSION' + Stores EXPRESSION as an IEEE double precision value. + +`.s_floating EXPRESSION' + Stores EXPRESSION as an IEEE single precision value. + +`.f_floating EXPRESSION' + Stores EXPRESSION as a VAX F format value. + +`.g_floating EXPRESSION' + Stores EXPRESSION as a VAX G format value. + +`.d_floating EXPRESSION' + Stores EXPRESSION as a VAX D format value. + +`.set FEATURE' + Enables or disables various assembler features. Using the positive + name of the feature enables while using `noFEATURE' disables. + + `at' + Indicates that macro expansions may clobber the "assembler + temporary" (`$at' or `$28') register. Some macros may not be + expanded without this and will generate an error message if + `noat' is in effect. When `at' is in effect, a warning will + be generated if `$at' is used by the programmer. + + `macro' + Enables the expansion of macro instructions. Note that + variants of real instructions, such as `br label' vs `br + $31,label' are considered alternate forms and not macros. + + `move' + `reorder' + `volatile' + These control whether and how the assembler may re-order + instructions. Accepted for compatibility with the OSF/1 + assembler, but `as' does not do instruction scheduling, so + these features are ignored. + + The following directives are recognized for compatibility with the +OSF/1 assembler but are ignored. + + .proc .aproc + .reguse .livereg + .option .aent + .ugen .eflag + .alias .noalias + + +File: as.info, Node: Alpha Opcodes, Prev: Alpha Directives, Up: Alpha-Dependent + +9.1.6 Opcodes +------------- + +For detailed information on the Alpha machine instruction set, see the +Alpha Architecture Handbook +(ftp://ftp.digital.com/pub/Digital/info/semiconductor/literature/alphaahb.pdf). + + +File: as.info, Node: ARC-Dependent, Next: ARM-Dependent, Prev: Alpha-Dependent, Up: Machine Dependencies + +9.2 ARC Dependent Features +========================== + +* Menu: + +* ARC Options:: Options +* ARC Syntax:: Syntax +* ARC Floating Point:: Floating Point +* ARC Directives:: ARC Machine Directives +* ARC Opcodes:: Opcodes + + +File: as.info, Node: ARC Options, Next: ARC Syntax, Up: ARC-Dependent + +9.2.1 Options +------------- + +`-marc[5|6|7|8]' + This option selects the core processor variant. Using `-marc' is + the same as `-marc6', which is also the default. + + `arc5' + Base instruction set. + + `arc6' + Jump-and-link (jl) instruction. No requirement of an + instruction between setting flags and conditional jump. For + example: + + mov.f r0,r1 + beq foo + + `arc7' + Break (brk) and sleep (sleep) instructions. + + `arc8' + Software interrupt (swi) instruction. + + + Note: the `.option' directive can to be used to select a core + variant from within assembly code. + +`-EB' + This option specifies that the output generated by the assembler + should be marked as being encoded for a big-endian processor. + +`-EL' + This option specifies that the output generated by the assembler + should be marked as being encoded for a little-endian processor - + this is the default. + + + +File: as.info, Node: ARC Syntax, Next: ARC Floating Point, Prev: ARC Options, Up: ARC-Dependent + +9.2.2 Syntax +------------ + +* Menu: + +* ARC-Chars:: Special Characters +* ARC-Regs:: Register Names + + +File: as.info, Node: ARC-Chars, Next: ARC-Regs, Up: ARC Syntax + +9.2.2.1 Special Characters +.......................... + +*TODO* + + +File: as.info, Node: ARC-Regs, Prev: ARC-Chars, Up: ARC Syntax + +9.2.2.2 Register Names +...................... + +*TODO* + + +File: as.info, Node: ARC Floating Point, Next: ARC Directives, Prev: ARC Syntax, Up: ARC-Dependent + +9.2.3 Floating Point +-------------------- + +The ARC core does not currently have hardware floating point support. +Software floating point support is provided by `GCC' and uses IEEE +floating-point numbers. + + +File: as.info, Node: ARC Directives, Next: ARC Opcodes, Prev: ARC Floating Point, Up: ARC-Dependent + +9.2.4 ARC Machine Directives +---------------------------- + +The ARC version of `as' supports the following additional machine +directives: + +`.2byte EXPRESSIONS' + *TODO* + +`.3byte EXPRESSIONS' + *TODO* + +`.4byte EXPRESSIONS' + *TODO* + +`.extAuxRegister NAME,ADDRESS,MODE' + The ARCtangent A4 has extensible auxiliary register space. The + auxiliary registers can be defined in the assembler source code by + using this directive. The first parameter is the NAME of the new + auxiallry register. The second parameter is the ADDRESS of the + register in the auxiliary register memory map for the variant of + the ARC. The third parameter specifies the MODE in which the + register can be operated is and it can be one of: + + `r (readonly)' + + `w (write only)' + + `r|w (read or write)' + + For example: + + .extAuxRegister mulhi,0x12,w + + This specifies an extension auxiliary register called _mulhi_ + which is at address 0x12 in the memory space and which is only + writable. + +`.extCondCode SUFFIX,VALUE' + The condition codes on the ARCtangent A4 are extensible and can be + specified by means of this assembler directive. They are specified + by the suffix and the value for the condition code. They can be + used to specify extra condition codes with any values. For + example: + + .extCondCode is_busy,0x14 + + add.is_busy r1,r2,r3 + bis_busy _main + +`.extCoreRegister NAME,REGNUM,MODE,SHORTCUT' + Specifies an extension core register NAME for the application. + This allows a register NAME with a valid REGNUM between 0 and 60, + with the following as valid values for MODE + + `_r_ (readonly)' + + `_w_ (write only)' + + `_r|w_ (read or write)' + + The other parameter gives a description of the register having a + SHORTCUT in the pipeline. The valid values are: + + `can_shortcut' + + `cannot_shortcut' + + For example: + + .extCoreRegister mlo,57,r,can_shortcut + + This defines an extension core register mlo with the value 57 which + can shortcut the pipeline. + +`.extInstruction NAME,OPCODE,SUBOPCODE,SUFFIXCLASS,SYNTAXCLASS' + The ARCtangent A4 allows the user to specify extension + instructions. The extension instructions are not macros. The + assembler creates encodings for use of these instructions + according to the specification by the user. The parameters are: + + *NAME + Name of the extension instruction + + *OPCODE + Opcode to be used. (Bits 27:31 in the encoding). Valid values + 0x10-0x1f or 0x03 + + *SUBOPCODE + Subopcode to be used. Valid values are from 0x09-0x3f. + However the correct value also depends on SYNTAXCLASS + + *SUFFIXCLASS + Determines the kinds of suffixes to be allowed. Valid values + are `SUFFIX_NONE', `SUFFIX_COND', `SUFFIX_FLAG' which + indicates the absence or presence of conditional suffixes and + flag setting by the extension instruction. It is also + possible to specify that an instruction sets the flags and is + conditional by using `SUFFIX_CODE' | `SUFFIX_FLAG'. + + *SYNTAXCLASS + Determines the syntax class for the instruction. It can have + the following values: + + ``SYNTAX_2OP':' + 2 Operand Instruction + + ``SYNTAX_3OP':' + 3 Operand Instruction + + In addition there could be modifiers for the syntax class as + described below: + + Syntax Class Modifiers are: + + - `OP1_MUST_BE_IMM': Modifies syntax class SYNTAX_3OP, + specifying that the first operand of a three-operand + instruction must be an immediate (i.e., the result is + discarded). OP1_MUST_BE_IMM is used by bitwise ORing it + with SYNTAX_3OP as given in the example below. This + could usually be used to set the flags using specific + instructions and not retain results. + + - `OP1_IMM_IMPLIED': Modifies syntax class SYNTAX_20P, it + specifies that there is an implied immediate destination + operand which does not appear in the syntax. For + example, if the source code contains an instruction like: + + inst r1,r2 + + it really means that the first argument is an implied + immediate (that is, the result is discarded). This is + the same as though the source code were: inst 0,r1,r2. + You use OP1_IMM_IMPLIED by bitwise ORing it with + SYNTAX_20P. + + + For example, defining 64-bit multiplier with immediate operands: + + .extInstruction mp64,0x14,0x0,SUFFIX_COND | SUFFIX_FLAG , + SYNTAX_3OP|OP1_MUST_BE_IMM + + The above specifies an extension instruction called mp64 which has + 3 operands, sets the flags, can be used with a condition code, for + which the first operand is an immediate. (Equivalent to + discarding the result of the operation). + + .extInstruction mul64,0x14,0x00,SUFFIX_COND, SYNTAX_2OP|OP1_IMM_IMPLIED + + This describes a 2 operand instruction with an implicit first + immediate operand. The result of this operation would be + discarded. + +`.half EXPRESSIONS' + *TODO* + +`.long EXPRESSIONS' + *TODO* + +`.option ARC|ARC5|ARC6|ARC7|ARC8' + The `.option' directive must be followed by the desired core + version. Again `arc' is an alias for `arc6'. + + Note: the `.option' directive overrides the command line option + `-marc'; a warning is emitted when the version is not consistent + between the two - even for the implicit default core version + (arc6). + +`.short EXPRESSIONS' + *TODO* + +`.word EXPRESSIONS' + *TODO* + + + +File: as.info, Node: ARC Opcodes, Prev: ARC Directives, Up: ARC-Dependent + +9.2.5 Opcodes +------------- + +For information on the ARC instruction set, see `ARC Programmers +Reference Manual', ARC International (www.arc.com) + + +File: as.info, Node: ARM-Dependent, Next: AVR-Dependent, Prev: ARC-Dependent, Up: Machine Dependencies + +9.3 ARM Dependent Features +========================== + +* Menu: + +* ARM Options:: Options +* ARM Syntax:: Syntax +* ARM Floating Point:: Floating Point +* ARM Directives:: ARM Machine Directives +* ARM Opcodes:: Opcodes +* ARM Mapping Symbols:: Mapping Symbols +* ARM Unwinding Tutorial:: Unwinding + + +File: as.info, Node: ARM Options, Next: ARM Syntax, Up: ARM-Dependent + +9.3.1 Options +------------- + +`-mcpu=PROCESSOR[+EXTENSION...]' + This option specifies the target processor. The assembler will + issue an error message if an attempt is made to assemble an + instruction which will not execute on the target processor. The + following processor names are recognized: `arm1', `arm2', `arm250', + `arm3', `arm6', `arm60', `arm600', `arm610', `arm620', `arm7', + `arm7m', `arm7d', `arm7dm', `arm7di', `arm7dmi', `arm70', `arm700', + `arm700i', `arm710', `arm710t', `arm720', `arm720t', `arm740t', + `arm710c', `arm7100', `arm7500', `arm7500fe', `arm7t', `arm7tdmi', + `arm7tdmi-s', `arm8', `arm810', `strongarm', `strongarm1', + `strongarm110', `strongarm1100', `strongarm1110', `arm9', `arm920', + `arm920t', `arm922t', `arm940t', `arm9tdmi', `fa526' (Faraday + FA526 processor), `fa626' (Faraday FA626 processor), `arm9e', + `arm926e', `arm926ej-s', `arm946e-r0', `arm946e', `arm946e-s', + `arm966e-r0', `arm966e', `arm966e-s', `arm968e-s', `arm10t', + `arm10tdmi', `arm10e', `arm1020', `arm1020t', `arm1020e', + `arm1022e', `arm1026ej-s', `fa626te' (Faraday FA626TE processor), + `fa726te' (Faraday FA726TE processor), `arm1136j-s', `arm1136jf-s', + `arm1156t2-s', `arm1156t2f-s', `arm1176jz-s', `arm1176jzf-s', + `mpcore', `mpcorenovfp', `cortex-a8', `cortex-a9', `cortex-r4', + `cortex-m3', `cortex-m1', `cortex-m0', `ep9312' (ARM920 with + Cirrus Maverick coprocessor), `i80200' (Intel XScale processor) + `iwmmxt' (Intel(r) XScale processor with Wireless MMX(tm) + technology coprocessor) and `xscale'. The special name `all' may + be used to allow the assembler to accept instructions valid for + any ARM processor. + + In addition to the basic instruction set, the assembler can be + told to accept various extension mnemonics that extend the + processor using the co-processor instruction space. For example, + `-mcpu=arm920+maverick' is equivalent to specifying + `-mcpu=ep9312'. The following extensions are currently supported: + `+maverick' `+iwmmxt' and `+xscale'. + +`-march=ARCHITECTURE[+EXTENSION...]' + This option specifies the target architecture. The assembler will + issue an error message if an attempt is made to assemble an + instruction which will not execute on the target architecture. + The following architecture names are recognized: `armv1', `armv2', + `armv2a', `armv2s', `armv3', `armv3m', `armv4', `armv4xm', + `armv4t', `armv4txm', `armv5', `armv5t', `armv5txm', `armv5te', + `armv5texp', `armv6', `armv6j', `armv6k', `armv6z', `armv6zk', + `armv7', `armv7-a', `armv7-r', `armv7-m', `iwmmxt' and `xscale'. + If both `-mcpu' and `-march' are specified, the assembler will use + the setting for `-mcpu'. + + The architecture option can be extended with the same instruction + set extension options as the `-mcpu' option. + +`-mfpu=FLOATING-POINT-FORMAT' + This option specifies the floating point format to assemble for. + The assembler will issue an error message if an attempt is made to + assemble an instruction which will not execute on the target + floating point unit. The following format options are recognized: + `softfpa', `fpe', `fpe2', `fpe3', `fpa', `fpa10', `fpa11', + `arm7500fe', `softvfp', `softvfp+vfp', `vfp', `vfp10', `vfp10-r0', + `vfp9', `vfpxd', `vfpv2' `vfpv3' `vfpv3-d16' `arm1020t', + `arm1020e', `arm1136jf-s', `maverick' and `neon'. + + In addition to determining which instructions are assembled, this + option also affects the way in which the `.double' assembler + directive behaves when assembling little-endian code. + + The default is dependent on the processor selected. For + Architecture 5 or later, the default is to assembler for VFP + instructions; for earlier architectures the default is to assemble + for FPA instructions. + +`-mthumb' + This option specifies that the assembler should start assembling + Thumb instructions; that is, it should behave as though the file + starts with a `.code 16' directive. + +`-mthumb-interwork' + This option specifies that the output generated by the assembler + should be marked as supporting interworking. + +`-mimplicit-it=never' +`-mimplicit-it=always' +`-mimplicit-it=arm' +`-mimplicit-it=thumb' + The `-mimplicit-it' option controls the behavior of the assembler + when conditional instructions are not enclosed in IT blocks. + There are four possible behaviors. If `never' is specified, such + constructs cause a warning in ARM code and an error in Thumb-2 + code. If `always' is specified, such constructs are accepted in + both ARM and Thumb-2 code, where the IT instruction is added + implicitly. If `arm' is specified, such constructs are accepted + in ARM code and cause an error in Thumb-2 code. If `thumb' is + specified, such constructs cause a warning in ARM code and are + accepted in Thumb-2 code. If you omit this option, the behavior + is equivalent to `-mimplicit-it=arm'. + +`-mapcs `[26|32]'' + This option specifies that the output generated by the assembler + should be marked as supporting the indicated version of the Arm + Procedure. Calling Standard. + +`-matpcs' + This option specifies that the output generated by the assembler + should be marked as supporting the Arm/Thumb Procedure Calling + Standard. If enabled this option will cause the assembler to + create an empty debugging section in the object file called + .arm.atpcs. Debuggers can use this to determine the ABI being + used by. + +`-mapcs-float' + This indicates the floating point variant of the APCS should be + used. In this variant floating point arguments are passed in FP + registers rather than integer registers. + +`-mapcs-reentrant' + This indicates that the reentrant variant of the APCS should be + used. This variant supports position independent code. + +`-mfloat-abi=ABI' + This option specifies that the output generated by the assembler + should be marked as using specified floating point ABI. The + following values are recognized: `soft', `softfp' and `hard'. + +`-meabi=VER' + This option specifies which EABI version the produced object files + should conform to. The following values are recognized: `gnu', `4' + and `5'. + +`-EB' + This option specifies that the output generated by the assembler + should be marked as being encoded for a big-endian processor. + +`-EL' + This option specifies that the output generated by the assembler + should be marked as being encoded for a little-endian processor. + +`-k' + This option specifies that the output of the assembler should be + marked as position-independent code (PIC). + +`--fix-v4bx' + Allow `BX' instructions in ARMv4 code. This is intended for use + with the linker option of the same name. + +`-mwarn-deprecated' +`-mno-warn-deprecated' + Enable or disable warnings about using deprecated options or + features. The default is to warn. + + + +File: as.info, Node: ARM Syntax, Next: ARM Floating Point, Prev: ARM Options, Up: ARM-Dependent + +9.3.2 Syntax +------------ + +* Menu: + +* ARM-Instruction-Set:: Instruction Set +* ARM-Chars:: Special Characters +* ARM-Regs:: Register Names +* ARM-Relocations:: Relocations + + +File: as.info, Node: ARM-Instruction-Set, Next: ARM-Chars, Up: ARM Syntax + +9.3.2.1 Instruction Set Syntax +.............................. + +Two slightly different syntaxes are support for ARM and THUMB +instructions. The default, `divided', uses the old style where ARM and +THUMB instructions had their own, separate syntaxes. The new, +`unified' syntax, which can be selected via the `.syntax' directive, +and has the following main features: + +* + Immediate operands do not require a `#' prefix. + +* + The `IT' instruction may appear, and if it does it is validated + against subsequent conditional affixes. In ARM mode it does not + generate machine code, in THUMB mode it does. + +* + For ARM instructions the conditional affixes always appear at the + end of the instruction. For THUMB instructions conditional + affixes can be used, but only inside the scope of an `IT' + instruction. + +* + All of the instructions new to the V6T2 architecture (and later) + are available. (Only a few such instructions can be written in the + `divided' syntax). + +* + The `.N' and `.W' suffixes are recognized and honored. + +* + All instructions set the flags if and only if they have an `s' + affix. + + +File: as.info, Node: ARM-Chars, Next: ARM-Regs, Prev: ARM-Instruction-Set, Up: ARM Syntax + +9.3.2.2 Special Characters +.......................... + +The presence of a `@' on a line indicates the start of a comment that +extends to the end of the current line. If a `#' appears as the first +character of a line, the whole line is treated as a comment. + + The `;' character can be used instead of a newline to separate +statements. + + Either `#' or `$' can be used to indicate immediate operands. + + *TODO* Explain about /data modifier on symbols. + + +File: as.info, Node: ARM-Regs, Next: ARM-Relocations, Prev: ARM-Chars, Up: ARM Syntax + +9.3.2.3 Register Names +...................... + +*TODO* Explain about ARM register naming, and the predefined names. + + +File: as.info, Node: ARM Floating Point, Next: ARM Directives, Prev: ARM Syntax, Up: ARM-Dependent + +9.3.3 Floating Point +-------------------- + +The ARM family uses IEEE floating-point numbers. + + +File: as.info, Node: ARM-Relocations, Prev: ARM-Regs, Up: ARM Syntax + +9.3.3.1 ARM relocation generation +................................. + +Specific data relocations can be generated by putting the relocation +name in parentheses after the symbol name. For example: + + .word foo(TARGET1) + + This will generate an `R_ARM_TARGET1' relocation against the symbol +FOO. The following relocations are supported: `GOT', `GOTOFF', +`TARGET1', `TARGET2', `SBREL', `TLSGD', `TLSLDM', `TLSLDO', `GOTTPOFF' +and `TPOFF'. + + For compatibility with older toolchains the assembler also accepts +`(PLT)' after branch targets. This will generate the deprecated +`R_ARM_PLT32' relocation. + + Relocations for `MOVW' and `MOVT' instructions can be generated by +prefixing the value with `#:lower16:' and `#:upper16' respectively. +For example to load the 32-bit address of foo into r0: + + MOVW r0, #:lower16:foo + MOVT r0, #:upper16:foo + + +File: as.info, Node: ARM Directives, Next: ARM Opcodes, Prev: ARM Floating Point, Up: ARM-Dependent + +9.3.4 ARM Machine Directives +---------------------------- + +`.2byte EXPRESSION [, EXPRESSION]*' +`.4byte EXPRESSION [, EXPRESSION]*' +`.8byte EXPRESSION [, EXPRESSION]*' + These directives write 2, 4 or 8 byte values to the output section. + +`.align EXPRESSION [, EXPRESSION]' + This is the generic .ALIGN directive. For the ARM however if the + first argument is zero (ie no alignment is needed) the assembler + will behave as if the argument had been 2 (ie pad to the next four + byte boundary). This is for compatibility with ARM's own + assembler. + +`.arch NAME' + Select the target architecture. Valid values for NAME are the + same as for the `-march' commandline option. + +`.arm' + This performs the same action as .CODE 32. + +`.pad #COUNT' + Generate unwinder annotations for a stack adjustment of COUNT + bytes. A positive value indicates the function prologue allocated + stack space by decrementing the stack pointer. + +`.bss' + This directive switches to the `.bss' section. + +`.cantunwind' + Prevents unwinding through the current function. No personality + routine or exception table data is required or permitted. + +`.code `[16|32]'' + This directive selects the instruction set being generated. The + value 16 selects Thumb, with the value 32 selecting ARM. + +`.cpu NAME' + Select the target processor. Valid values for NAME are the same as + for the `-mcpu' commandline option. + +`NAME .dn REGISTER NAME [.TYPE] [[INDEX]]' + +`NAME .qn REGISTER NAME [.TYPE] [[INDEX]]' + The `dn' and `qn' directives are used to create typed and/or + indexed register aliases for use in Advanced SIMD Extension (Neon) + instructions. The former should be used to create aliases of + double-precision registers, and the latter to create aliases of + quad-precision registers. + + If these directives are used to create typed aliases, those + aliases can be used in Neon instructions instead of writing types + after the mnemonic or after each operand. For example: + + x .dn d2.f32 + y .dn d3.f32 + z .dn d4.f32[1] + vmul x,y,z + + This is equivalent to writing the following: + + vmul.f32 d2,d3,d4[1] + + Aliases created using `dn' or `qn' can be destroyed using `unreq'. + +`.eabi_attribute TAG, VALUE' + Set the EABI object attribute TAG to VALUE. + + The TAG is either an attribute number, or one of the following: + `Tag_CPU_raw_name', `Tag_CPU_name', `Tag_CPU_arch', + `Tag_CPU_arch_profile', `Tag_ARM_ISA_use', `Tag_THUMB_ISA_use', + `Tag_VFP_arch', `Tag_WMMX_arch', `Tag_Advanced_SIMD_arch', + `Tag_PCS_config', `Tag_ABI_PCS_R9_use', `Tag_ABI_PCS_RW_data', + `Tag_ABI_PCS_RO_data', `Tag_ABI_PCS_GOT_use', + `Tag_ABI_PCS_wchar_t', `Tag_ABI_FP_rounding', + `Tag_ABI_FP_denormal', `Tag_ABI_FP_exceptions', + `Tag_ABI_FP_user_exceptions', `Tag_ABI_FP_number_model', + `Tag_ABI_align8_needed', `Tag_ABI_align8_preserved', + `Tag_ABI_enum_size', `Tag_ABI_HardFP_use', `Tag_ABI_VFP_args', + `Tag_ABI_WMMX_args', `Tag_ABI_optimization_goals', + `Tag_ABI_FP_optimization_goals', `Tag_compatibility', + `Tag_CPU_unaligned_access', `Tag_VFP_HP_extension', + `Tag_ABI_FP_16bit_format', `Tag_nodefaults', + `Tag_also_compatible_with', `Tag_conformance', `Tag_T2EE_use', + `Tag_Virtualization_use', `Tag_MPextension_use' + + The VALUE is either a `number', `"string"', or `number, "string"' + depending on the tag. + +`.even' + This directive aligns to an even-numbered address. + +`.extend EXPRESSION [, EXPRESSION]*' +`.ldouble EXPRESSION [, EXPRESSION]*' + These directives write 12byte long double floating-point values to + the output section. These are not compatible with current ARM + processors or ABIs. + +`.fnend' + Marks the end of a function with an unwind table entry. The + unwind index table entry is created when this directive is + processed. + + If no personality routine has been specified then standard + personality routine 0 or 1 will be used, depending on the number + of unwind opcodes required. + +`.fnstart' + Marks the start of a function with an unwind table entry. + +`.force_thumb' + This directive forces the selection of Thumb instructions, even if + the target processor does not support those instructions + +`.fpu NAME' + Select the floating-point unit to assemble for. Valid values for + NAME are the same as for the `-mfpu' commandline option. + +`.handlerdata' + Marks the end of the current function, and the start of the + exception table entry for that function. Anything between this + directive and the `.fnend' directive will be added to the + exception table entry. + + Must be preceded by a `.personality' or `.personalityindex' + directive. + +`.inst OPCODE [ , ... ]' + +`.inst.n OPCODE [ , ... ]' + +`.inst.w OPCODE [ , ... ]' + Generates the instruction corresponding to the numerical value + OPCODE. `.inst.n' and `.inst.w' allow the Thumb instruction size + to be specified explicitly, overriding the normal encoding rules. + +`.ldouble EXPRESSION [, EXPRESSION]*' + See `.extend'. + +`.ltorg' + This directive causes the current contents of the literal pool to + be dumped into the current section (which is assumed to be the + .text section) at the current location (aligned to a word + boundary). `GAS' maintains a separate literal pool for each + section and each sub-section. The `.ltorg' directive will only + affect the literal pool of the current section and sub-section. + At the end of assembly all remaining, un-empty literal pools will + automatically be dumped. + + Note - older versions of `GAS' would dump the current literal pool + any time a section change occurred. This is no longer done, since + it prevents accurate control of the placement of literal pools. + +`.movsp REG [, #OFFSET]' + Tell the unwinder that REG contains an offset from the current + stack pointer. If OFFSET is not specified then it is assumed to be + zero. + +`.object_arch NAME' + Override the architecture recorded in the EABI object attribute + section. Valid values for NAME are the same as for the `.arch' + directive. Typically this is useful when code uses runtime + detection of CPU features. + +`.packed EXPRESSION [, EXPRESSION]*' + This directive writes 12-byte packed floating-point values to the + output section. These are not compatible with current ARM + processors or ABIs. + +`.pad #COUNT' + Generate unwinder annotations for a stack adjustment of COUNT + bytes. A positive value indicates the function prologue allocated + stack space by decrementing the stack pointer. + +`.personality NAME' + Sets the personality routine for the current function to NAME. + +`.personalityindex INDEX' + Sets the personality routine for the current function to the EABI + standard routine number INDEX + +`.pool' + This is a synonym for .ltorg. + +`NAME .req REGISTER NAME' + This creates an alias for REGISTER NAME called NAME. For example: + + foo .req r0 + +`.save REGLIST' + Generate unwinder annotations to restore the registers in REGLIST. + The format of REGLIST is the same as the corresponding + store-multiple instruction. + + _core registers_ + .save {r4, r5, r6, lr} + stmfd sp!, {r4, r5, r6, lr} + _FPA registers_ + .save f4, 2 + sfmfd f4, 2, [sp]! + _VFP registers_ + .save {d8, d9, d10} + fstmdx sp!, {d8, d9, d10} + _iWMMXt registers_ + .save {wr10, wr11} + wstrd wr11, [sp, #-8]! + wstrd wr10, [sp, #-8]! + or + .save wr11 + wstrd wr11, [sp, #-8]! + .save wr10 + wstrd wr10, [sp, #-8]! + +`.setfp FPREG, SPREG [, #OFFSET]' + Make all unwinder annotations relative to a frame pointer. + Without this the unwinder will use offsets from the stack pointer. + + The syntax of this directive is the same as the `sub' or `mov' + instruction used to set the frame pointer. SPREG must be either + `sp' or mentioned in a previous `.movsp' directive. + + .movsp ip + mov ip, sp + ... + .setfp fp, ip, #4 + sub fp, ip, #4 + +`.secrel32 EXPRESSION [, EXPRESSION]*' + This directive emits relocations that evaluate to the + section-relative offset of each expression's symbol. This + directive is only supported for PE targets. + +`.syntax [`unified' | `divided']' + This directive sets the Instruction Set Syntax as described in the + *Note ARM-Instruction-Set:: section. + +`.thumb' + This performs the same action as .CODE 16. + +`.thumb_func' + This directive specifies that the following symbol is the name of a + Thumb encoded function. This information is necessary in order to + allow the assembler and linker to generate correct code for + interworking between Arm and Thumb instructions and should be used + even if interworking is not going to be performed. The presence + of this directive also implies `.thumb' + + This directive is not neccessary when generating EABI objects. On + these targets the encoding is implicit when generating Thumb code. + +`.thumb_set' + This performs the equivalent of a `.set' directive in that it + creates a symbol which is an alias for another symbol (possibly + not yet defined). This directive also has the added property in + that it marks the aliased symbol as being a thumb function entry + point, in the same way that the `.thumb_func' directive does. + +`.unreq ALIAS-NAME' + This undefines a register alias which was previously defined using + the `req', `dn' or `qn' directives. For example: + + foo .req r0 + .unreq foo + + An error occurs if the name is undefined. Note - this pseudo op + can be used to delete builtin in register name aliases (eg 'r0'). + This should only be done if it is really necessary. + +`.unwind_raw OFFSET, BYTE1, ...' + Insert one of more arbitary unwind opcode bytes, which are known + to adjust the stack pointer by OFFSET bytes. + + For example `.unwind_raw 4, 0xb1, 0x01' is equivalent to `.save + {r0}' + +`.vsave VFP-REGLIST' + Generate unwinder annotations to restore the VFP registers in + VFP-REGLIST using FLDMD. Also works for VFPv3 registers that are + to be restored using VLDM. The format of VFP-REGLIST is the same + as the corresponding store-multiple instruction. + + _VFP registers_ + .vsave {d8, d9, d10} + fstmdd sp!, {d8, d9, d10} + _VFPv3 registers_ + .vsave {d15, d16, d17} + vstm sp!, {d15, d16, d17} + + Since FLDMX and FSTMX are now deprecated, this directive should be + used in favour of `.save' for saving VFP registers for ARMv6 and + above. + + + +File: as.info, Node: ARM Opcodes, Next: ARM Mapping Symbols, Prev: ARM Directives, Up: ARM-Dependent + +9.3.5 Opcodes +------------- + +`as' implements all the standard ARM opcodes. It also implements +several pseudo opcodes, including several synthetic load instructions. + +`NOP' + nop + + This pseudo op will always evaluate to a legal ARM instruction + that does nothing. Currently it will evaluate to MOV r0, r0. + +`LDR' + ldr <register> , = <expression> + + If expression evaluates to a numeric constant then a MOV or MVN + instruction will be used in place of the LDR instruction, if the + constant can be generated by either of these instructions. + Otherwise the constant will be placed into the nearest literal + pool (if it not already there) and a PC relative LDR instruction + will be generated. + +`ADR' + adr <register> <label> + + This instruction will load the address of LABEL into the indicated + register. The instruction will evaluate to a PC relative ADD or + SUB instruction depending upon where the label is located. If the + label is out of range, or if it is not defined in the same file + (and section) as the ADR instruction, then an error will be + generated. This instruction will not make use of the literal pool. + +`ADRL' + adrl <register> <label> + + This instruction will load the address of LABEL into the indicated + register. The instruction will evaluate to one or two PC relative + ADD or SUB instructions depending upon where the label is located. + If a second instruction is not needed a NOP instruction will be + generated in its place, so that this instruction is always 8 bytes + long. + + If the label is out of range, or if it is not defined in the same + file (and section) as the ADRL instruction, then an error will be + generated. This instruction will not make use of the literal pool. + + + For information on the ARM or Thumb instruction sets, see `ARM +Software Development Toolkit Reference Manual', Advanced RISC Machines +Ltd. + + +File: as.info, Node: ARM Mapping Symbols, Next: ARM Unwinding Tutorial, Prev: ARM Opcodes, Up: ARM-Dependent + +9.3.6 Mapping Symbols +--------------------- + +The ARM ELF specification requires that special symbols be inserted +into object files to mark certain features: + +`$a' + At the start of a region of code containing ARM instructions. + +`$t' + At the start of a region of code containing THUMB instructions. + +`$d' + At the start of a region of data. + + + The assembler will automatically insert these symbols for you - there +is no need to code them yourself. Support for tagging symbols ($b, $f, +$p and $m) which is also mentioned in the current ARM ELF specification +is not implemented. This is because they have been dropped from the +new EABI and so tools cannot rely upon their presence. + + +File: as.info, Node: ARM Unwinding Tutorial, Prev: ARM Mapping Symbols, Up: ARM-Dependent + +9.3.7 Unwinding +--------------- + +The ABI for the ARM Architecture specifies a standard format for +exception unwind information. This information is used when an +exception is thrown to determine where control should be transferred. +In particular, the unwind information is used to determine which +function called the function that threw the exception, and which +function called that one, and so forth. This information is also used +to restore the values of callee-saved registers in the function +catching the exception. + + If you are writing functions in assembly code, and those functions +call other functions that throw exceptions, you must use assembly +pseudo ops to ensure that appropriate exception unwind information is +generated. Otherwise, if one of the functions called by your assembly +code throws an exception, the run-time library will be unable to unwind +the stack through your assembly code and your program will not behave +correctly. + + To illustrate the use of these pseudo ops, we will examine the code +that G++ generates for the following C++ input: + + +void callee (int *); + +int +caller () +{ + int i; + callee (&i); + return i; +} + + This example does not show how to throw or catch an exception from +assembly code. That is a much more complex operation and should always +be done in a high-level language, such as C++, that directly supports +exceptions. + + The code generated by one particular version of G++ when compiling +the example above is: + + +_Z6callerv: + .fnstart +.LFB2: + @ Function supports interworking. + @ args = 0, pretend = 0, frame = 8 + @ frame_needed = 1, uses_anonymous_args = 0 + stmfd sp!, {fp, lr} + .save {fp, lr} +.LCFI0: + .setfp fp, sp, #4 + add fp, sp, #4 +.LCFI1: + .pad #8 + sub sp, sp, #8 +.LCFI2: + sub r3, fp, #8 + mov r0, r3 + bl _Z6calleePi + ldr r3, [fp, #-8] + mov r0, r3 + sub sp, fp, #4 + ldmfd sp!, {fp, lr} + bx lr +.LFE2: + .fnend + + Of course, the sequence of instructions varies based on the options +you pass to GCC and on the version of GCC in use. The exact +instructions are not important since we are focusing on the pseudo ops +that are used to generate unwind information. + + An important assumption made by the unwinder is that the stack frame +does not change during the body of the function. In particular, since +we assume that the assembly code does not itself throw an exception, +the only point where an exception can be thrown is from a call, such as +the `bl' instruction above. At each call site, the same saved +registers (including `lr', which indicates the return address) must be +located in the same locations relative to the frame pointer. + + The `.fnstart' (*note .fnstart pseudo op: arm_fnstart.) pseudo op +appears immediately before the first instruction of the function while +the `.fnend' (*note .fnend pseudo op: arm_fnend.) pseudo op appears +immediately after the last instruction of the function. These pseudo +ops specify the range of the function. + + Only the order of the other pseudos ops (e.g., `.setfp' or `.pad') +matters; their exact locations are irrelevant. In the example above, +the compiler emits the pseudo ops with particular instructions. That +makes it easier to understand the code, but it is not required for +correctness. It would work just as well to emit all of the pseudo ops +other than `.fnend' in the same order, but immediately after `.fnstart'. + + The `.save' (*note .save pseudo op: arm_save.) pseudo op indicates +registers that have been saved to the stack so that they can be +restored before the function returns. The argument to the `.save' +pseudo op is a list of registers to save. If a register is +"callee-saved" (as specified by the ABI) and is modified by the +function you are writing, then your code must save the value before it +is modified and restore the original value before the function returns. +If an exception is thrown, the run-time library restores the values of +these registers from their locations on the stack before returning +control to the exception handler. (Of course, if an exception is not +thrown, the function that contains the `.save' pseudo op restores these +registers in the function epilogue, as is done with the `ldmfd' +instruction above.) + + You do not have to save callee-saved registers at the very beginning +of the function and you do not need to use the `.save' pseudo op +immediately following the point at which the registers are saved. +However, if you modify a callee-saved register, you must save it on the +stack before modifying it and before calling any functions which might +throw an exception. And, you must use the `.save' pseudo op to +indicate that you have done so. + + The `.pad' (*note .pad: arm_pad.) pseudo op indicates a modification +of the stack pointer that does not save any registers. The argument is +the number of bytes (in decimal) that are subtracted from the stack +pointer. (On ARM CPUs, the stack grows downwards, so subtracting from +the stack pointer increases the size of the stack.) + + The `.setfp' (*note .setfp pseudo op: arm_setfp.) pseudo op +indicates the register that contains the frame pointer. The first +argument is the register that is set, which is typically `fp'. The +second argument indicates the register from which the frame pointer +takes its value. The third argument, if present, is the value (in +decimal) added to the register specified by the second argument to +compute the value of the frame pointer. You should not modify the +frame pointer in the body of the function. + + If you do not use a frame pointer, then you should not use the +`.setfp' pseudo op. If you do not use a frame pointer, then you should +avoid modifying the stack pointer outside of the function prologue. +Otherwise, the run-time library will be unable to find saved registers +when it is unwinding the stack. + + The pseudo ops described above are sufficient for writing assembly +code that calls functions which may throw exceptions. If you need to +know more about the object-file format used to represent unwind +information, you may consult the `Exception Handling ABI for the ARM +Architecture' available from `http://infocenter.arm.com'. + + +File: as.info, Node: AVR-Dependent, Next: Blackfin-Dependent, Prev: ARM-Dependent, Up: Machine Dependencies + +9.4 AVR Dependent Features +========================== + +* Menu: + +* AVR Options:: Options +* AVR Syntax:: Syntax +* AVR Opcodes:: Opcodes + + +File: as.info, Node: AVR Options, Next: AVR Syntax, Up: AVR-Dependent + +9.4.1 Options +------------- + +`-mmcu=MCU' + Specify ATMEL AVR instruction set or MCU type. + + Instruction set avr1 is for the minimal AVR core, not supported by + the C compiler, only for assembler programs (MCU types: at90s1200, + attiny11, attiny12, attiny15, attiny28). + + Instruction set avr2 (default) is for the classic AVR core with up + to 8K program memory space (MCU types: at90s2313, at90s2323, + at90s2333, at90s2343, attiny22, attiny26, at90s4414, at90s4433, + at90s4434, at90s8515, at90c8534, at90s8535). + + Instruction set avr25 is for the classic AVR core with up to 8K + program memory space plus the MOVW instruction (MCU types: + attiny13, attiny13a, attiny2313, attiny2313a, attiny24, attiny24a, + attiny4313, attiny44, attiny44a, attiny84, attiny25, attiny45, + attiny85, attiny261, attiny261a, attiny461, attiny861, attiny861a, + attiny87, attiny43u, attiny48, attiny88, at86rf401, ata6289). + + Instruction set avr3 is for the classic AVR core with up to 128K + program memory space (MCU types: at43usb355, at76c711). + + Instruction set avr31 is for the classic AVR core with exactly + 128K program memory space (MCU types: atmega103, at43usb320). + + Instruction set avr35 is for classic AVR core plus MOVW, CALL, and + JMP instructions (MCU types: attiny167, attiny327, at90usb82, + at90usb162, atmega8u2, atmega16u2, atmega32u2). + + Instruction set avr4 is for the enhanced AVR core with up to 8K + program memory space (MCU types: atmega48, atmega48p,atmega8, + atmega88, atmega88p, atmega8515, atmega8535, atmega8hva, + atmega4hvd, atmega8hvd, at90pwm1, at90pwm2, at90pwm2b, at90pwm3, + at90pwm3b, at90pwm81, atmega8m1, atmega8c1). + + Instruction set avr5 is for the enhanced AVR core with up to 128K + program memory space (MCU types: atmega16, atmega161, atmega162, + atmega163, atmega164p, atmega165, atmega165p, atmega168, + atmega168p, atmega169, atmega169p, atmega16c1, atmega32, + atmega323, atmega324p, atmega325, atmega325p, atmega3250, + atmega3250p, atmega328p, atmega329, atmega329p, atmega3290, + atmega3290p, atmega406, atmega64, atmega640, atmega644, + atmega644p, atmega644pa, atmega645, atmega6450, atmega649, + atmega6490, atmega16hva, atmega16hvb, atmega32hvb, at90can32, + at90can64, at90pwm216, at90pwm316, atmega32c1, atmega64c1, + atmega16m1, atmega32m1, atmega64m1, atmega16u4, atmega32u4, + atmega32u6, at90usb646, at90usb647, at94k, at90scr100). + + Instruction set avr51 is for the enhanced AVR core with exactly + 128K program memory space (MCU types: atmega128, atmega1280, + atmega1281, atmega1284p, atmega128rfa1, at90can128, at90usb1286, + at90usb1287, m3000f, m3000s, m3001b). + + Instruction set avr6 is for the enhanced AVR core with a 3-byte PC + (MCU types: atmega2560, atmega2561). + +`-mall-opcodes' + Accept all AVR opcodes, even if not supported by `-mmcu'. + +`-mno-skip-bug' + This option disable warnings for skipping two-word instructions. + +`-mno-wrap' + This option reject `rjmp/rcall' instructions with 8K wrap-around. + + + +File: as.info, Node: AVR Syntax, Next: AVR Opcodes, Prev: AVR Options, Up: AVR-Dependent + +9.4.2 Syntax +------------ + +* Menu: + +* AVR-Chars:: Special Characters +* AVR-Regs:: Register Names +* AVR-Modifiers:: Relocatable Expression Modifiers + + +File: as.info, Node: AVR-Chars, Next: AVR-Regs, Up: AVR Syntax + +9.4.2.1 Special Characters +.......................... + +The presence of a `;' on a line indicates the start of a comment that +extends to the end of the current line. If a `#' appears as the first +character of a line, the whole line is treated as a comment. + + The `$' character can be used instead of a newline to separate +statements. + + +File: as.info, Node: AVR-Regs, Next: AVR-Modifiers, Prev: AVR-Chars, Up: AVR Syntax + +9.4.2.2 Register Names +...................... + +The AVR has 32 x 8-bit general purpose working registers `r0', `r1', +... `r31'. Six of the 32 registers can be used as three 16-bit +indirect address register pointers for Data Space addressing. One of +the these address pointers can also be used as an address pointer for +look up tables in Flash program memory. These added function registers +are the 16-bit `X', `Y' and `Z' - registers. + + X = r26:r27 + Y = r28:r29 + Z = r30:r31 + + +File: as.info, Node: AVR-Modifiers, Prev: AVR-Regs, Up: AVR Syntax + +9.4.2.3 Relocatable Expression Modifiers +........................................ + +The assembler supports several modifiers when using relocatable +addresses in AVR instruction operands. The general syntax is the +following: + + modifier(relocatable-expression) + +`lo8' + This modifier allows you to use bits 0 through 7 of an address + expression as 8 bit relocatable expression. + +`hi8' + This modifier allows you to use bits 7 through 15 of an address + expression as 8 bit relocatable expression. This is useful with, + for example, the AVR `ldi' instruction and `lo8' modifier. + + For example + + ldi r26, lo8(sym+10) + ldi r27, hi8(sym+10) + +`hh8' + This modifier allows you to use bits 16 through 23 of an address + expression as 8 bit relocatable expression. Also, can be useful + for loading 32 bit constants. + +`hlo8' + Synonym of `hh8'. + +`hhi8' + This modifier allows you to use bits 24 through 31 of an + expression as 8 bit expression. This is useful with, for example, + the AVR `ldi' instruction and `lo8', `hi8', `hlo8', `hhi8', + modifier. + + For example + + ldi r26, lo8(285774925) + ldi r27, hi8(285774925) + ldi r28, hlo8(285774925) + ldi r29, hhi8(285774925) + ; r29,r28,r27,r26 = 285774925 + +`pm_lo8' + This modifier allows you to use bits 0 through 7 of an address + expression as 8 bit relocatable expression. This modifier useful + for addressing data or code from Flash/Program memory. The using + of `pm_lo8' similar to `lo8'. + +`pm_hi8' + This modifier allows you to use bits 8 through 15 of an address + expression as 8 bit relocatable expression. This modifier useful + for addressing data or code from Flash/Program memory. + +`pm_hh8' + This modifier allows you to use bits 15 through 23 of an address + expression as 8 bit relocatable expression. This modifier useful + for addressing data or code from Flash/Program memory. + + + +File: as.info, Node: AVR Opcodes, Prev: AVR Syntax, Up: AVR-Dependent + +9.4.3 Opcodes +------------- + +For detailed information on the AVR machine instruction set, see +`www.atmel.com/products/AVR'. + + `as' implements all the standard AVR opcodes. The following table +summarizes the AVR opcodes, and their arguments. + + Legend: + r any register + d `ldi' register (r16-r31) + v `movw' even register (r0, r2, ..., r28, r30) + a `fmul' register (r16-r23) + w `adiw' register (r24,r26,r28,r30) + e pointer registers (X,Y,Z) + b base pointer register and displacement ([YZ]+disp) + z Z pointer register (for [e]lpm Rd,Z[+]) + M immediate value from 0 to 255 + n immediate value from 0 to 255 ( n = ~M ). Relocation impossible + s immediate value from 0 to 7 + P Port address value from 0 to 63. (in, out) + p Port address value from 0 to 31. (cbi, sbi, sbic, sbis) + K immediate value from 0 to 63 (used in `adiw', `sbiw') + i immediate value + l signed pc relative offset from -64 to 63 + L signed pc relative offset from -2048 to 2047 + h absolute code address (call, jmp) + S immediate value from 0 to 7 (S = s << 4) + ? use this opcode entry if no parameters, else use next opcode entry + + 1001010010001000 clc + 1001010011011000 clh + 1001010011111000 cli + 1001010010101000 cln + 1001010011001000 cls + 1001010011101000 clt + 1001010010111000 clv + 1001010010011000 clz + 1001010000001000 sec + 1001010001011000 seh + 1001010001111000 sei + 1001010000101000 sen + 1001010001001000 ses + 1001010001101000 set + 1001010000111000 sev + 1001010000011000 sez + 100101001SSS1000 bclr S + 100101000SSS1000 bset S + 1001010100001001 icall + 1001010000001001 ijmp + 1001010111001000 lpm ? + 1001000ddddd010+ lpm r,z + 1001010111011000 elpm ? + 1001000ddddd011+ elpm r,z + 0000000000000000 nop + 1001010100001000 ret + 1001010100011000 reti + 1001010110001000 sleep + 1001010110011000 break + 1001010110101000 wdr + 1001010111101000 spm + 000111rdddddrrrr adc r,r + 000011rdddddrrrr add r,r + 001000rdddddrrrr and r,r + 000101rdddddrrrr cp r,r + 000001rdddddrrrr cpc r,r + 000100rdddddrrrr cpse r,r + 001001rdddddrrrr eor r,r + 001011rdddddrrrr mov r,r + 100111rdddddrrrr mul r,r + 001010rdddddrrrr or r,r + 000010rdddddrrrr sbc r,r + 000110rdddddrrrr sub r,r + 001001rdddddrrrr clr r + 000011rdddddrrrr lsl r + 000111rdddddrrrr rol r + 001000rdddddrrrr tst r + 0111KKKKddddKKKK andi d,M + 0111KKKKddddKKKK cbr d,n + 1110KKKKddddKKKK ldi d,M + 11101111dddd1111 ser d + 0110KKKKddddKKKK ori d,M + 0110KKKKddddKKKK sbr d,M + 0011KKKKddddKKKK cpi d,M + 0100KKKKddddKKKK sbci d,M + 0101KKKKddddKKKK subi d,M + 1111110rrrrr0sss sbrc r,s + 1111111rrrrr0sss sbrs r,s + 1111100ddddd0sss bld r,s + 1111101ddddd0sss bst r,s + 10110PPdddddPPPP in r,P + 10111PPrrrrrPPPP out P,r + 10010110KKddKKKK adiw w,K + 10010111KKddKKKK sbiw w,K + 10011000pppppsss cbi p,s + 10011010pppppsss sbi p,s + 10011001pppppsss sbic p,s + 10011011pppppsss sbis p,s + 111101lllllll000 brcc l + 111100lllllll000 brcs l + 111100lllllll001 breq l + 111101lllllll100 brge l + 111101lllllll101 brhc l + 111100lllllll101 brhs l + 111101lllllll111 brid l + 111100lllllll111 brie l + 111100lllllll000 brlo l + 111100lllllll100 brlt l + 111100lllllll010 brmi l + 111101lllllll001 brne l + 111101lllllll010 brpl l + 111101lllllll000 brsh l + 111101lllllll110 brtc l + 111100lllllll110 brts l + 111101lllllll011 brvc l + 111100lllllll011 brvs l + 111101lllllllsss brbc s,l + 111100lllllllsss brbs s,l + 1101LLLLLLLLLLLL rcall L + 1100LLLLLLLLLLLL rjmp L + 1001010hhhhh111h call h + 1001010hhhhh110h jmp h + 1001010rrrrr0101 asr r + 1001010rrrrr0000 com r + 1001010rrrrr1010 dec r + 1001010rrrrr0011 inc r + 1001010rrrrr0110 lsr r + 1001010rrrrr0001 neg r + 1001000rrrrr1111 pop r + 1001001rrrrr1111 push r + 1001010rrrrr0111 ror r + 1001010rrrrr0010 swap r + 00000001ddddrrrr movw v,v + 00000010ddddrrrr muls d,d + 000000110ddd0rrr mulsu a,a + 000000110ddd1rrr fmul a,a + 000000111ddd0rrr fmuls a,a + 000000111ddd1rrr fmulsu a,a + 1001001ddddd0000 sts i,r + 1001000ddddd0000 lds r,i + 10o0oo0dddddbooo ldd r,b + 100!000dddddee-+ ld r,e + 10o0oo1rrrrrbooo std b,r + 100!001rrrrree-+ st e,r + 1001010100011001 eicall + 1001010000011001 eijmp + + +File: as.info, Node: Blackfin-Dependent, Next: CR16-Dependent, Prev: AVR-Dependent, Up: Machine Dependencies + +9.5 Blackfin Dependent Features +=============================== + +* Menu: + +* Blackfin Options:: Blackfin Options +* Blackfin Syntax:: Blackfin Syntax +* Blackfin Directives:: Blackfin Directives + + +File: as.info, Node: Blackfin Options, Next: Blackfin Syntax, Up: Blackfin-Dependent + +9.5.1 Options +------------- + +`-mcpu=PROCESSOR[-SIREVISION]' + This option specifies the target processor. The optional + SIREVISION is not used in assembler. It's here such that GCC can + easily pass down its `-mcpu=' option. The assembler will issue an + error message if an attempt is made to assemble an instruction + which will not execute on the target processor. The following + processor names are recognized: `bf512', `bf514', `bf516', `bf518', + `bf522', `bf523', `bf524', `bf525', `bf526', `bf527', `bf531', + `bf532', `bf533', `bf534', `bf535' (not implemented yet), `bf536', + `bf537', `bf538', `bf539', `bf542', `bf542m', `bf544', `bf544m', + `bf547', `bf547m', `bf548', `bf548m', `bf549', `bf549m', and + `bf561'. + + + +File: as.info, Node: Blackfin Syntax, Next: Blackfin Directives, Prev: Blackfin Options, Up: Blackfin-Dependent + +9.5.2 Syntax +------------ + +`Special Characters' + Assembler input is free format and may appear anywhere on the line. + One instruction may extend across multiple lines or more than one + instruction may appear on the same line. White space (space, tab, + comments or newline) may appear anywhere between tokens. A token + must not have embedded spaces. Tokens include numbers, register + names, keywords, user identifiers, and also some multicharacter + special symbols like "+=", "/*" or "||". + +`Instruction Delimiting' + A semicolon must terminate every instruction. Sometimes a complete + instruction will consist of more than one operation. There are two + cases where this occurs. The first is when two general operations + are combined. Normally a comma separates the different parts, as + in + + a0= r3.h * r2.l, a1 = r3.l * r2.h ; + + The second case occurs when a general instruction is combined with + one or two memory references for joint issue. The latter portions + are set off by a "||" token. + + a0 = r3.h * r2.l || r1 = [p3++] || r4 = [i2++]; + +`Register Names' + The assembler treats register names and instruction keywords in a + case insensitive manner. User identifiers are case sensitive. + Thus, R3.l, R3.L, r3.l and r3.L are all equivalent input to the + assembler. + + Register names are reserved and may not be used as program + identifiers. + + Some operations (such as "Move Register") require a register pair. + Register pairs are always data registers and are denoted using a + colon, eg., R3:2. The larger number must be written firsts. Note + that the hardware only supports odd-even pairs, eg., R7:6, R5:4, + R3:2, and R1:0. + + Some instructions (such as -SP (Push Multiple)) require a group of + adjacent registers. Adjacent registers are denoted in the syntax + by the range enclosed in parentheses and separated by a colon, + eg., (R7:3). Again, the larger number appears first. + + Portions of a particular register may be individually specified. + This is written with a dot (".") following the register name and + then a letter denoting the desired portion. For 32-bit registers, + ".H" denotes the most significant ("High") portion. ".L" denotes + the least-significant portion. The subdivisions of the 40-bit + registers are described later. + +`Accumulators' + The set of 40-bit registers A1 and A0 that normally contain data + that is being manipulated. Each accumulator can be accessed in + four ways. + + `one 40-bit register' + The register will be referred to as A1 or A0. + + `one 32-bit register' + The registers are designated as A1.W or A0.W. + + `two 16-bit registers' + The registers are designated as A1.H, A1.L, A0.H or A0.L. + + `one 8-bit register' + The registers are designated as A1.X or A0.X for the bits that + extend beyond bit 31. + +`Data Registers' + The set of 32-bit registers (R0, R1, R2, R3, R4, R5, R6 and R7) + that normally contain data for manipulation. These are + abbreviated as D-register or Dreg. Data registers can be accessed + as 32-bit registers or as two independent 16-bit registers. The + least significant 16 bits of each register is called the "low" + half and is designated with ".L" following the register name. The + most significant 16 bits are called the "high" half and is + designated with ".H" following the name. + + R7.L, r2.h, r4.L, R0.H + +`Pointer Registers' + The set of 32-bit registers (P0, P1, P2, P3, P4, P5, SP and FP) + that normally contain byte addresses of data structures. These are + abbreviated as P-register or Preg. + + p2, p5, fp, sp + +`Stack Pointer SP' + The stack pointer contains the 32-bit address of the last occupied + byte location in the stack. The stack grows by decrementing the + stack pointer. + +`Frame Pointer FP' + The frame pointer contains the 32-bit address of the previous frame + pointer in the stack. It is located at the top of a frame. + +`Loop Top' + LT0 and LT1. These registers contain the 32-bit address of the + top of a zero overhead loop. + +`Loop Count' + LC0 and LC1. These registers contain the 32-bit counter of the + zero overhead loop executions. + +`Loop Bottom' + LB0 and LB1. These registers contain the 32-bit address of the + bottom of a zero overhead loop. + +`Index Registers' + The set of 32-bit registers (I0, I1, I2, I3) that normally contain + byte addresses of data structures. Abbreviated I-register or Ireg. + +`Modify Registers' + The set of 32-bit registers (M0, M1, M2, M3) that normally contain + offset values that are added and subracted to one of the index + registers. Abbreviated as Mreg. + +`Length Registers' + The set of 32-bit registers (L0, L1, L2, L3) that normally contain + the length in bytes of the circular buffer. Abbreviated as Lreg. + Clear the Lreg to disable circular addressing for the + corresponding Ireg. + +`Base Registers' + The set of 32-bit registers (B0, B1, B2, B3) that normally contain + the base address in bytes of the circular buffer. Abbreviated as + Breg. + +`Floating Point' + The Blackfin family has no hardware floating point but the .float + directive generates ieee floating point numbers for use with + software floating point libraries. + +`Blackfin Opcodes' + For detailed information on the Blackfin machine instruction set, + see the Blackfin(r) Processor Instruction Set Reference. + + + +File: as.info, Node: Blackfin Directives, Prev: Blackfin Syntax, Up: Blackfin-Dependent + +9.5.3 Directives +---------------- + +The following directives are provided for compatibility with the VDSP +assembler. + +`.byte2' + Initializes a four byte data object. + +`.byte4' + Initializes a two byte data object. + +`.db' + TBD + +`.dd' + TBD + +`.dw' + TBD + +`.var' + Define and initialize a 32 bit data object. + + +File: as.info, Node: CR16-Dependent, Next: CRIS-Dependent, Prev: Blackfin-Dependent, Up: Machine Dependencies + +9.6 CR16 Dependent Features +=========================== + +* Menu: + +* CR16 Operand Qualifiers:: CR16 Machine Operand Qualifiers + + +File: as.info, Node: CR16 Operand Qualifiers, Up: CR16-Dependent + +9.6.1 CR16 Operand Qualifiers +----------------------------- + +The National Semiconductor CR16 target of `as' has a few machine +dependent operand qualifiers. + + Operand expression type qualifier is an optional field in the +instruction operand, to determines the type of the expression field of +an operand. The `@' is required. CR16 architecture uses one of the +following expression qualifiers: + +`s' + - `Specifies expression operand type as small' + +`m' + - `Specifies expression operand type as medium' + +`l' + - `Specifies expression operand type as large' + +`c' + - `Specifies the CR16 Assembler generates a relocation entry for + the operand, where pc has implied bit, the expression is adjusted + accordingly. The linker uses the relocation entry to update the + operand address at link time.' + +`got/GOT' + - `Specifies the CR16 Assembler generates a relocation entry for + the operand, offset from Global Offset Table. The linker uses this + relocation entry to update the operand address at link time' + +`cgot/cGOT' + - `Specifies the CompactRISC Assembler generates a relocation + entry for the operand, where pc has implied bit, the expression is + adjusted accordingly. The linker uses the relocation entry to + update the operand address at link time.' + + CR16 target operand qualifiers and its size (in bits): + +`Immediate Operand' + - s --- 4 bits + +`' + - m --- 16 bits, for movb and movw instructions. + +`' + - m --- 20 bits, movd instructions. + +`' + - l --- 32 bits + +`Absolute Operand' + - s --- Illegal specifier for this operand. + +`' + - m --- 20 bits, movd instructions. + +`Displacement Operand' + - s --- 8 bits + +`' + - m --- 16 bits + +`' + - l --- 24 bits + + For example: + 1 `movw $_myfun@c,r1' + + This loads the address of _myfun, shifted right by 1, into r1. + + 2 `movd $_myfun@c,(r2,r1)' + + This loads the address of _myfun, shifted right by 1, into register-pair r2-r1. + + 3 `_myfun_ptr:' + `.long _myfun@c' + `loadd _myfun_ptr, (r1,r0)' + `jal (r1,r0)' + + This .long directive, the address of _myfunc, shifted right by 1 at link time. + + 4 `loadd _data1@GOT(r12), (r1,r0)' + + This loads the address of _data1, into global offset table (ie GOT) and its offset value from GOT loads into register-pair r2-r1. + + 5 `loadd _myfunc@cGOT(r12), (r1,r0)' + + This loads the address of _myfun, shifted right by 1, into global offset table (ie GOT) and its offset value from GOT loads into register-pair r1-r0. + + +File: as.info, Node: CRIS-Dependent, Next: D10V-Dependent, Prev: CR16-Dependent, Up: Machine Dependencies + +9.7 CRIS Dependent Features +=========================== + +* Menu: + +* CRIS-Opts:: Command-line Options +* CRIS-Expand:: Instruction expansion +* CRIS-Symbols:: Symbols +* CRIS-Syntax:: Syntax + + +File: as.info, Node: CRIS-Opts, Next: CRIS-Expand, Up: CRIS-Dependent + +9.7.1 Command-line Options +-------------------------- + +The CRIS version of `as' has these machine-dependent command-line +options. + + The format of the generated object files can be either ELF or a.out, +specified by the command-line options `--emulation=crisaout' and +`--emulation=criself'. The default is ELF (criself), unless `as' has +been configured specifically for a.out by using the configuration name +`cris-axis-aout'. + + There are two different link-incompatible ELF object file variants +for CRIS, for use in environments where symbols are expected to be +prefixed by a leading `_' character and for environments without such a +symbol prefix. The variant used for GNU/Linux port has no symbol +prefix. Which variant to produce is specified by either of the options +`--underscore' and `--no-underscore'. The default is `--underscore'. +Since symbols in CRIS a.out objects are expected to have a `_' prefix, +specifying `--no-underscore' when generating a.out objects is an error. +Besides the object format difference, the effect of this option is to +parse register names differently (*note crisnous::). The +`--no-underscore' option makes a `$' register prefix mandatory. + + The option `--pic' must be passed to `as' in order to recognize the +symbol syntax used for ELF (SVR4 PIC) position-independent-code (*note +crispic::). This will also affect expansion of instructions. The +expansion with `--pic' will use PC-relative rather than (slightly +faster) absolute addresses in those expansions. + + The option `--march=ARCHITECTURE' specifies the recognized +instruction set and recognized register names. It also controls the +architecture type of the object file. Valid values for ARCHITECTURE +are: +`v0_v10' + All instructions and register names for any architecture variant + in the set v0...v10 are recognized. This is the default if the + target is configured as cris-*. + +`v10' + Only instructions and register names for CRIS v10 (as found in + ETRAX 100 LX) are recognized. This is the default if the target + is configured as crisv10-*. + +`v32' + Only instructions and register names for CRIS v32 (code name + Guinness) are recognized. This is the default if the target is + configured as crisv32-*. This value implies `--no-mul-bug-abort'. + (A subsequent `--mul-bug-abort' will turn it back on.) + +`common_v10_v32' + Only instructions with register names and addressing modes with + opcodes common to the v10 and v32 are recognized. + + When `-N' is specified, `as' will emit a warning when a 16-bit +branch instruction is expanded into a 32-bit multiple-instruction +construct (*note CRIS-Expand::). + + Some versions of the CRIS v10, for example in the Etrax 100 LX, +contain a bug that causes destabilizing memory accesses when a multiply +instruction is executed with certain values in the first operand just +before a cache-miss. When the `--mul-bug-abort' command line option is +active (the default value), `as' will refuse to assemble a file +containing a multiply instruction at a dangerous offset, one that could +be the last on a cache-line, or is in a section with insufficient +alignment. This placement checking does not catch any case where the +multiply instruction is dangerously placed because it is located in a +delay-slot. The `--mul-bug-abort' command line option turns off the +checking. + + +File: as.info, Node: CRIS-Expand, Next: CRIS-Symbols, Prev: CRIS-Opts, Up: CRIS-Dependent + +9.7.2 Instruction expansion +--------------------------- + +`as' will silently choose an instruction that fits the operand size for +`[register+constant]' operands. For example, the offset `127' in +`move.d [r3+127],r4' fits in an instruction using a signed-byte offset. +Similarly, `move.d [r2+32767],r1' will generate an instruction using a +16-bit offset. For symbolic expressions and constants that do not fit +in 16 bits including the sign bit, a 32-bit offset is generated. + + For branches, `as' will expand from a 16-bit branch instruction into +a sequence of instructions that can reach a full 32-bit address. Since +this does not correspond to a single instruction, such expansions can +optionally be warned about. *Note CRIS-Opts::. + + If the operand is found to fit the range, a `lapc' mnemonic will +translate to a `lapcq' instruction. Use `lapc.d' to force the 32-bit +`lapc' instruction. + + Similarly, the `addo' mnemonic will translate to the shortest +fitting instruction of `addoq', `addo.w' and `addo.d', when used with a +operand that is a constant known at assembly time. + + +File: as.info, Node: CRIS-Symbols, Next: CRIS-Syntax, Prev: CRIS-Expand, Up: CRIS-Dependent + +9.7.3 Symbols +------------- + +Some symbols are defined by the assembler. They're intended to be used +in conditional assembly, for example: + .if ..asm.arch.cris.v32 + CODE FOR CRIS V32 + .elseif ..asm.arch.cris.common_v10_v32 + CODE COMMON TO CRIS V32 AND CRIS V10 + .elseif ..asm.arch.cris.v10 | ..asm.arch.cris.any_v0_v10 + CODE FOR V10 + .else + .error "Code needs to be added here." + .endif + + These symbols are defined in the assembler, reflecting command-line +options, either when specified or the default. They are always +defined, to 0 or 1. +`..asm.arch.cris.any_v0_v10' + This symbol is non-zero when `--march=v0_v10' is specified or the + default. + +`..asm.arch.cris.common_v10_v32' + Set according to the option `--march=common_v10_v32'. + +`..asm.arch.cris.v10' + Reflects the option `--march=v10'. + +`..asm.arch.cris.v32' + Corresponds to `--march=v10'. + + Speaking of symbols, when a symbol is used in code, it can have a +suffix modifying its value for use in position-independent code. *Note +CRIS-Pic::. + + +File: as.info, Node: CRIS-Syntax, Prev: CRIS-Symbols, Up: CRIS-Dependent + +9.7.4 Syntax +------------ + +There are different aspects of the CRIS assembly syntax. + +* Menu: + +* CRIS-Chars:: Special Characters +* CRIS-Pic:: Position-Independent Code Symbols +* CRIS-Regs:: Register Names +* CRIS-Pseudos:: Assembler Directives + + +File: as.info, Node: CRIS-Chars, Next: CRIS-Pic, Up: CRIS-Syntax + +9.7.4.1 Special Characters +.......................... + +The character `#' is a line comment character. It starts a comment if +and only if it is placed at the beginning of a line. + + A `;' character starts a comment anywhere on the line, causing all +characters up to the end of the line to be ignored. + + A `@' character is handled as a line separator equivalent to a +logical new-line character (except in a comment), so separate +instructions can be specified on a single line. + + +File: as.info, Node: CRIS-Pic, Next: CRIS-Regs, Prev: CRIS-Chars, Up: CRIS-Syntax + +9.7.4.2 Symbols in position-independent code +............................................ + +When generating position-independent code (SVR4 PIC) for use in +cris-axis-linux-gnu or crisv32-axis-linux-gnu shared libraries, symbol +suffixes are used to specify what kind of run-time symbol lookup will +be used, expressed in the object as different _relocation types_. +Usually, all absolute symbol values must be located in a table, the +_global offset table_, leaving the code position-independent; +independent of values of global symbols and independent of the address +of the code. The suffix modifies the value of the symbol, into for +example an index into the global offset table where the real symbol +value is entered, or a PC-relative value, or a value relative to the +start of the global offset table. All symbol suffixes start with the +character `:' (omitted in the list below). Every symbol use in code or +a read-only section must therefore have a PIC suffix to enable a useful +shared library to be created. Usually, these constructs must not be +used with an additive constant offset as is usually allowed, i.e. no 4 +as in `symbol + 4' is allowed. This restriction is checked at +link-time, not at assembly-time. + +`GOT' + Attaching this suffix to a symbol in an instruction causes the + symbol to be entered into the global offset table. The value is a + 32-bit index for that symbol into the global offset table. The + name of the corresponding relocation is `R_CRIS_32_GOT'. Example: + `move.d [$r0+extsym:GOT],$r9' + +`GOT16' + Same as for `GOT', but the value is a 16-bit index into the global + offset table. The corresponding relocation is `R_CRIS_16_GOT'. + Example: `move.d [$r0+asymbol:GOT16],$r10' + +`PLT' + This suffix is used for function symbols. It causes a _procedure + linkage table_, an array of code stubs, to be created at the time + the shared object is created or linked against, together with a + global offset table entry. The value is a pc-relative offset to + the corresponding stub code in the procedure linkage table. This + arrangement causes the run-time symbol resolver to be called to + look up and set the value of the symbol the first time the + function is called (at latest; depending environment variables). + It is only safe to leave the symbol unresolved this way if all + references are function calls. The name of the relocation is + `R_CRIS_32_PLT_PCREL'. Example: `add.d fnname:PLT,$pc' + +`PLTG' + Like PLT, but the value is relative to the beginning of the global + offset table. The relocation is `R_CRIS_32_PLT_GOTREL'. Example: + `move.d fnname:PLTG,$r3' + +`GOTPLT' + Similar to `PLT', but the value of the symbol is a 32-bit index + into the global offset table. This is somewhat of a mix between + the effect of the `GOT' and the `PLT' suffix; the difference to + `GOT' is that there will be a procedure linkage table entry + created, and that the symbol is assumed to be a function entry and + will be resolved by the run-time resolver as with `PLT'. The + relocation is `R_CRIS_32_GOTPLT'. Example: `jsr + [$r0+fnname:GOTPLT]' + +`GOTPLT16' + A variant of `GOTPLT' giving a 16-bit value. Its relocation name + is `R_CRIS_16_GOTPLT'. Example: `jsr [$r0+fnname:GOTPLT16]' + +`GOTOFF' + This suffix must only be attached to a local symbol, but may be + used in an expression adding an offset. The value is the address + of the symbol relative to the start of the global offset table. + The relocation name is `R_CRIS_32_GOTREL'. Example: `move.d + [$r0+localsym:GOTOFF],r3' + + +File: as.info, Node: CRIS-Regs, Next: CRIS-Pseudos, Prev: CRIS-Pic, Up: CRIS-Syntax + +9.7.4.3 Register names +...................... + +A `$' character may always prefix a general or special register name in +an instruction operand but is mandatory when the option +`--no-underscore' is specified or when the `.syntax register_prefix' +directive is in effect (*note crisnous::). Register names are +case-insensitive. + + +File: as.info, Node: CRIS-Pseudos, Prev: CRIS-Regs, Up: CRIS-Syntax + +9.7.4.4 Assembler Directives +............................ + +There are a few CRIS-specific pseudo-directives in addition to the +generic ones. *Note Pseudo Ops::. Constants emitted by +pseudo-directives are in little-endian order for CRIS. There is no +support for floating-point-specific directives for CRIS. + +`.dword EXPRESSIONS' + The `.dword' directive is a synonym for `.int', expecting zero or + more EXPRESSIONS, separated by commas. For each expression, a + 32-bit little-endian constant is emitted. + +`.syntax ARGUMENT' + The `.syntax' directive takes as ARGUMENT one of the following + case-sensitive choices. + + `no_register_prefix' + The `.syntax no_register_prefix' directive makes a `$' + character prefix on all registers optional. It overrides a + previous setting, including the corresponding effect of the + option `--no-underscore'. If this directive is used when + ordinary symbols do not have a `_' character prefix, care + must be taken to avoid ambiguities whether an operand is a + register or a symbol; using symbols with names the same as + general or special registers then invoke undefined behavior. + + `register_prefix' + This directive makes a `$' character prefix on all registers + mandatory. It overrides a previous setting, including the + corresponding effect of the option `--underscore'. + + `leading_underscore' + This is an assertion directive, emitting an error if the + `--no-underscore' option is in effect. + + `no_leading_underscore' + This is the opposite of the `.syntax leading_underscore' + directive and emits an error if the option `--underscore' is + in effect. + +`.arch ARGUMENT' + This is an assertion directive, giving an error if the specified + ARGUMENT is not the same as the specified or default value for the + `--march=ARCHITECTURE' option (*note march-option::). + + + +File: as.info, Node: D10V-Dependent, Next: D30V-Dependent, Prev: CRIS-Dependent, Up: Machine Dependencies + +9.8 D10V Dependent Features +=========================== + +* Menu: + +* D10V-Opts:: D10V Options +* D10V-Syntax:: Syntax +* D10V-Float:: Floating Point +* D10V-Opcodes:: Opcodes + + +File: as.info, Node: D10V-Opts, Next: D10V-Syntax, Up: D10V-Dependent + +9.8.1 D10V Options +------------------ + +The Mitsubishi D10V version of `as' has a few machine dependent options. + +`-O' + The D10V can often execute two sub-instructions in parallel. When + this option is used, `as' will attempt to optimize its output by + detecting when instructions can be executed in parallel. + +`--nowarnswap' + To optimize execution performance, `as' will sometimes swap the + order of instructions. Normally this generates a warning. When + this option is used, no warning will be generated when + instructions are swapped. + +`--gstabs-packing' + +`--no-gstabs-packing' + `as' packs adjacent short instructions into a single packed + instruction. `--no-gstabs-packing' turns instruction packing off if + `--gstabs' is specified as well; `--gstabs-packing' (the default) + turns instruction packing on even when `--gstabs' is specified. + + +File: as.info, Node: D10V-Syntax, Next: D10V-Float, Prev: D10V-Opts, Up: D10V-Dependent + +9.8.2 Syntax +------------ + +The D10V syntax is based on the syntax in Mitsubishi's D10V +architecture manual. The differences are detailed below. + +* Menu: + +* D10V-Size:: Size Modifiers +* D10V-Subs:: Sub-Instructions +* D10V-Chars:: Special Characters +* D10V-Regs:: Register Names +* D10V-Addressing:: Addressing Modes +* D10V-Word:: @WORD Modifier + + +File: as.info, Node: D10V-Size, Next: D10V-Subs, Up: D10V-Syntax + +9.8.2.1 Size Modifiers +...................... + +The D10V version of `as' uses the instruction names in the D10V +Architecture Manual. However, the names in the manual are sometimes +ambiguous. There are instruction names that can assemble to a short or +long form opcode. How does the assembler pick the correct form? `as' +will always pick the smallest form if it can. When dealing with a +symbol that is not defined yet when a line is being assembled, it will +always use the long form. If you need to force the assembler to use +either the short or long form of the instruction, you can append either +`.s' (short) or `.l' (long) to it. For example, if you are writing an +assembly program and you want to do a branch to a symbol that is +defined later in your program, you can write `bra.s foo'. Objdump +and GDB will always append `.s' or `.l' to instructions which have both +short and long forms. + + +File: as.info, Node: D10V-Subs, Next: D10V-Chars, Prev: D10V-Size, Up: D10V-Syntax + +9.8.2.2 Sub-Instructions +........................ + +The D10V assembler takes as input a series of instructions, either +one-per-line, or in the special two-per-line format described in the +next section. Some of these instructions will be short-form or +sub-instructions. These sub-instructions can be packed into a single +instruction. The assembler will do this automatically. It will also +detect when it should not pack instructions. For example, when a label +is defined, the next instruction will never be packaged with the +previous one. Whenever a branch and link instruction is called, it +will not be packaged with the next instruction so the return address +will be valid. Nops are automatically inserted when necessary. + + If you do not want the assembler automatically making these +decisions, you can control the packaging and execution type (parallel +or sequential) with the special execution symbols described in the next +section. + + +File: as.info, Node: D10V-Chars, Next: D10V-Regs, Prev: D10V-Subs, Up: D10V-Syntax + +9.8.2.3 Special Characters +.......................... + +`;' and `#' are the line comment characters. Sub-instructions may be +executed in order, in reverse-order, or in parallel. Instructions +listed in the standard one-per-line format will be executed +sequentially. To specify the executing order, use the following +symbols: +`->' + Sequential with instruction on the left first. + +`<-' + Sequential with instruction on the right first. + +`||' + Parallel + The D10V syntax allows either one instruction per line, one +instruction per line with the execution symbol, or two instructions per +line. For example +`abs a1 -> abs r0' + Execute these sequentially. The instruction on the right is in + the right container and is executed second. + +`abs r0 <- abs a1' + Execute these reverse-sequentially. The instruction on the right + is in the right container, and is executed first. + +`ld2w r2,@r8+ || mac a0,r0,r7' + Execute these in parallel. + +`ld2w r2,@r8+ ||' +`mac a0,r0,r7' + Two-line format. Execute these in parallel. + +`ld2w r2,@r8+' +`mac a0,r0,r7' + Two-line format. Execute these sequentially. Assembler will put + them in the proper containers. + +`ld2w r2,@r8+ ->' +`mac a0,r0,r7' + Two-line format. Execute these sequentially. Same as above but + second instruction will always go into right container. + Since `$' has no special meaning, you may use it in symbol names. + + +File: as.info, Node: D10V-Regs, Next: D10V-Addressing, Prev: D10V-Chars, Up: D10V-Syntax + +9.8.2.4 Register Names +...................... + +You can use the predefined symbols `r0' through `r15' to refer to the +D10V registers. You can also use `sp' as an alias for `r15'. The +accumulators are `a0' and `a1'. There are special register-pair names +that may optionally be used in opcodes that require even-numbered +registers. Register names are not case sensitive. + + Register Pairs +`r0-r1' + +`r2-r3' + +`r4-r5' + +`r6-r7' + +`r8-r9' + +`r10-r11' + +`r12-r13' + +`r14-r15' + + The D10V also has predefined symbols for these control registers and +status bits: +`psw' + Processor Status Word + +`bpsw' + Backup Processor Status Word + +`pc' + Program Counter + +`bpc' + Backup Program Counter + +`rpt_c' + Repeat Count + +`rpt_s' + Repeat Start address + +`rpt_e' + Repeat End address + +`mod_s' + Modulo Start address + +`mod_e' + Modulo End address + +`iba' + Instruction Break Address + +`f0' + Flag 0 + +`f1' + Flag 1 + +`c' + Carry flag + + +File: as.info, Node: D10V-Addressing, Next: D10V-Word, Prev: D10V-Regs, Up: D10V-Syntax + +9.8.2.5 Addressing Modes +........................ + +`as' understands the following addressing modes for the D10V. `RN' in +the following refers to any of the numbered registers, but _not_ the +control registers. +`RN' + Register direct + +`@RN' + Register indirect + +`@RN+' + Register indirect with post-increment + +`@RN-' + Register indirect with post-decrement + +`@-SP' + Register indirect with pre-decrement + +`@(DISP, RN)' + Register indirect with displacement + +`ADDR' + PC relative address (for branch or rep). + +`#IMM' + Immediate data (the `#' is optional and ignored) + + +File: as.info, Node: D10V-Word, Prev: D10V-Addressing, Up: D10V-Syntax + +9.8.2.6 @WORD Modifier +...................... + +Any symbol followed by `@word' will be replaced by the symbol's value +shifted right by 2. This is used in situations such as loading a +register with the address of a function (or any other code fragment). +For example, if you want to load a register with the location of the +function `main' then jump to that function, you could do it as follows: + ldi r2, main@word + jmp r2 + + +File: as.info, Node: D10V-Float, Next: D10V-Opcodes, Prev: D10V-Syntax, Up: D10V-Dependent + +9.8.3 Floating Point +-------------------- + +The D10V has no hardware floating point, but the `.float' and `.double' +directives generates IEEE floating-point numbers for compatibility with +other development tools. + + +File: as.info, Node: D10V-Opcodes, Prev: D10V-Float, Up: D10V-Dependent + +9.8.4 Opcodes +------------- + +For detailed information on the D10V machine instruction set, see `D10V +Architecture: A VLIW Microprocessor for Multimedia Applications' +(Mitsubishi Electric Corp.). `as' implements all the standard D10V +opcodes. The only changes are those described in the section on size +modifiers + + +File: as.info, Node: D30V-Dependent, Next: H8/300-Dependent, Prev: D10V-Dependent, Up: Machine Dependencies + +9.9 D30V Dependent Features +=========================== + +* Menu: + +* D30V-Opts:: D30V Options +* D30V-Syntax:: Syntax +* D30V-Float:: Floating Point +* D30V-Opcodes:: Opcodes + + +File: as.info, Node: D30V-Opts, Next: D30V-Syntax, Up: D30V-Dependent + +9.9.1 D30V Options +------------------ + +The Mitsubishi D30V version of `as' has a few machine dependent options. + +`-O' + The D30V can often execute two sub-instructions in parallel. When + this option is used, `as' will attempt to optimize its output by + detecting when instructions can be executed in parallel. + +`-n' + When this option is used, `as' will issue a warning every time it + adds a nop instruction. + +`-N' + When this option is used, `as' will issue a warning if it needs to + insert a nop after a 32-bit multiply before a load or 16-bit + multiply instruction. + + +File: as.info, Node: D30V-Syntax, Next: D30V-Float, Prev: D30V-Opts, Up: D30V-Dependent + +9.9.2 Syntax +------------ + +The D30V syntax is based on the syntax in Mitsubishi's D30V +architecture manual. The differences are detailed below. + +* Menu: + +* D30V-Size:: Size Modifiers +* D30V-Subs:: Sub-Instructions +* D30V-Chars:: Special Characters +* D30V-Guarded:: Guarded Execution +* D30V-Regs:: Register Names +* D30V-Addressing:: Addressing Modes + + +File: as.info, Node: D30V-Size, Next: D30V-Subs, Up: D30V-Syntax + +9.9.2.1 Size Modifiers +...................... + +The D30V version of `as' uses the instruction names in the D30V +Architecture Manual. However, the names in the manual are sometimes +ambiguous. There are instruction names that can assemble to a short or +long form opcode. How does the assembler pick the correct form? `as' +will always pick the smallest form if it can. When dealing with a +symbol that is not defined yet when a line is being assembled, it will +always use the long form. If you need to force the assembler to use +either the short or long form of the instruction, you can append either +`.s' (short) or `.l' (long) to it. For example, if you are writing an +assembly program and you want to do a branch to a symbol that is +defined later in your program, you can write `bra.s foo'. Objdump and +GDB will always append `.s' or `.l' to instructions which have both +short and long forms. + + +File: as.info, Node: D30V-Subs, Next: D30V-Chars, Prev: D30V-Size, Up: D30V-Syntax + +9.9.2.2 Sub-Instructions +........................ + +The D30V assembler takes as input a series of instructions, either +one-per-line, or in the special two-per-line format described in the +next section. Some of these instructions will be short-form or +sub-instructions. These sub-instructions can be packed into a single +instruction. The assembler will do this automatically. It will also +detect when it should not pack instructions. For example, when a label +is defined, the next instruction will never be packaged with the +previous one. Whenever a branch and link instruction is called, it +will not be packaged with the next instruction so the return address +will be valid. Nops are automatically inserted when necessary. + + If you do not want the assembler automatically making these +decisions, you can control the packaging and execution type (parallel +or sequential) with the special execution symbols described in the next +section. + + +File: as.info, Node: D30V-Chars, Next: D30V-Guarded, Prev: D30V-Subs, Up: D30V-Syntax + +9.9.2.3 Special Characters +.......................... + +`;' and `#' are the line comment characters. Sub-instructions may be +executed in order, in reverse-order, or in parallel. Instructions +listed in the standard one-per-line format will be executed +sequentially unless you use the `-O' option. + + To specify the executing order, use the following symbols: +`->' + Sequential with instruction on the left first. + +`<-' + Sequential with instruction on the right first. + +`||' + Parallel + + The D30V syntax allows either one instruction per line, one +instruction per line with the execution symbol, or two instructions per +line. For example +`abs r2,r3 -> abs r4,r5' + Execute these sequentially. The instruction on the right is in + the right container and is executed second. + +`abs r2,r3 <- abs r4,r5' + Execute these reverse-sequentially. The instruction on the right + is in the right container, and is executed first. + +`abs r2,r3 || abs r4,r5' + Execute these in parallel. + +`ldw r2,@(r3,r4) ||' +`mulx r6,r8,r9' + Two-line format. Execute these in parallel. + +`mulx a0,r8,r9' +`stw r2,@(r3,r4)' + Two-line format. Execute these sequentially unless `-O' option is + used. If the `-O' option is used, the assembler will determine if + the instructions could be done in parallel (the above two + instructions can be done in parallel), and if so, emit them as + parallel instructions. The assembler will put them in the proper + containers. In the above example, the assembler will put the + `stw' instruction in left container and the `mulx' instruction in + the right container. + +`stw r2,@(r3,r4) ->' +`mulx a0,r8,r9' + Two-line format. Execute the `stw' instruction followed by the + `mulx' instruction sequentially. The first instruction goes in the + left container and the second instruction goes into right + container. The assembler will give an error if the machine + ordering constraints are violated. + +`stw r2,@(r3,r4) <-' +`mulx a0,r8,r9' + Same as previous example, except that the `mulx' instruction is + executed before the `stw' instruction. + + Since `$' has no special meaning, you may use it in symbol names. + + +File: as.info, Node: D30V-Guarded, Next: D30V-Regs, Prev: D30V-Chars, Up: D30V-Syntax + +9.9.2.4 Guarded Execution +......................... + +`as' supports the full range of guarded execution directives for each +instruction. Just append the directive after the instruction proper. +The directives are: + +`/tx' + Execute the instruction if flag f0 is true. + +`/fx' + Execute the instruction if flag f0 is false. + +`/xt' + Execute the instruction if flag f1 is true. + +`/xf' + Execute the instruction if flag f1 is false. + +`/tt' + Execute the instruction if both flags f0 and f1 are true. + +`/tf' + Execute the instruction if flag f0 is true and flag f1 is false. + + +File: as.info, Node: D30V-Regs, Next: D30V-Addressing, Prev: D30V-Guarded, Up: D30V-Syntax + +9.9.2.5 Register Names +...................... + +You can use the predefined symbols `r0' through `r63' to refer to the +D30V registers. You can also use `sp' as an alias for `r63' and `link' +as an alias for `r62'. The accumulators are `a0' and `a1'. + + The D30V also has predefined symbols for these control registers and +status bits: +`psw' + Processor Status Word + +`bpsw' + Backup Processor Status Word + +`pc' + Program Counter + +`bpc' + Backup Program Counter + +`rpt_c' + Repeat Count + +`rpt_s' + Repeat Start address + +`rpt_e' + Repeat End address + +`mod_s' + Modulo Start address + +`mod_e' + Modulo End address + +`iba' + Instruction Break Address + +`f0' + Flag 0 + +`f1' + Flag 1 + +`f2' + Flag 2 + +`f3' + Flag 3 + +`f4' + Flag 4 + +`f5' + Flag 5 + +`f6' + Flag 6 + +`f7' + Flag 7 + +`s' + Same as flag 4 (saturation flag) + +`v' + Same as flag 5 (overflow flag) + +`va' + Same as flag 6 (sticky overflow flag) + +`c' + Same as flag 7 (carry/borrow flag) + +`b' + Same as flag 7 (carry/borrow flag) + + +File: as.info, Node: D30V-Addressing, Prev: D30V-Regs, Up: D30V-Syntax + +9.9.2.6 Addressing Modes +........................ + +`as' understands the following addressing modes for the D30V. `RN' in +the following refers to any of the numbered registers, but _not_ the +control registers. +`RN' + Register direct + +`@RN' + Register indirect + +`@RN+' + Register indirect with post-increment + +`@RN-' + Register indirect with post-decrement + +`@-SP' + Register indirect with pre-decrement + +`@(DISP, RN)' + Register indirect with displacement + +`ADDR' + PC relative address (for branch or rep). + +`#IMM' + Immediate data (the `#' is optional and ignored) + + +File: as.info, Node: D30V-Float, Next: D30V-Opcodes, Prev: D30V-Syntax, Up: D30V-Dependent + +9.9.3 Floating Point +-------------------- + +The D30V has no hardware floating point, but the `.float' and `.double' +directives generates IEEE floating-point numbers for compatibility with +other development tools. + + +File: as.info, Node: D30V-Opcodes, Prev: D30V-Float, Up: D30V-Dependent + +9.9.4 Opcodes +------------- + +For detailed information on the D30V machine instruction set, see `D30V +Architecture: A VLIW Microprocessor for Multimedia Applications' +(Mitsubishi Electric Corp.). `as' implements all the standard D30V +opcodes. The only changes are those described in the section on size +modifiers + + +File: as.info, Node: H8/300-Dependent, Next: HPPA-Dependent, Prev: D30V-Dependent, Up: Machine Dependencies + +9.10 H8/300 Dependent Features +============================== + +* Menu: + +* H8/300 Options:: Options +* H8/300 Syntax:: Syntax +* H8/300 Floating Point:: Floating Point +* H8/300 Directives:: H8/300 Machine Directives +* H8/300 Opcodes:: Opcodes + + +File: as.info, Node: H8/300 Options, Next: H8/300 Syntax, Up: H8/300-Dependent + +9.10.1 Options +-------------- + +The Renesas H8/300 version of `as' has one machine-dependent option: + +`-h-tick-hex' + Support H'00 style hex constants in addition to 0x00 style. + + + +File: as.info, Node: H8/300 Syntax, Next: H8/300 Floating Point, Prev: H8/300 Options, Up: H8/300-Dependent + +9.10.2 Syntax +------------- + +* Menu: + +* H8/300-Chars:: Special Characters +* H8/300-Regs:: Register Names +* H8/300-Addressing:: Addressing Modes + + +File: as.info, Node: H8/300-Chars, Next: H8/300-Regs, Up: H8/300 Syntax + +9.10.2.1 Special Characters +........................... + +`;' is the line comment character. + + `$' can be used instead of a newline to separate statements. +Therefore _you may not use `$' in symbol names_ on the H8/300. + + +File: as.info, Node: H8/300-Regs, Next: H8/300-Addressing, Prev: H8/300-Chars, Up: H8/300 Syntax + +9.10.2.2 Register Names +....................... + +You can use predefined symbols of the form `rNh' and `rNl' to refer to +the H8/300 registers as sixteen 8-bit general-purpose registers. N is +a digit from `0' to `7'); for instance, both `r0h' and `r7l' are valid +register names. + + You can also use the eight predefined symbols `rN' to refer to the +H8/300 registers as 16-bit registers (you must use this form for +addressing). + + On the H8/300H, you can also use the eight predefined symbols `erN' +(`er0' ... `er7') to refer to the 32-bit general purpose registers. + + The two control registers are called `pc' (program counter; a 16-bit +register, except on the H8/300H where it is 24 bits) and `ccr' +(condition code register; an 8-bit register). `r7' is used as the +stack pointer, and can also be called `sp'. + + +File: as.info, Node: H8/300-Addressing, Prev: H8/300-Regs, Up: H8/300 Syntax + +9.10.2.3 Addressing Modes +......................... + +as understands the following addressing modes for the H8/300: +`rN' + Register direct + +`@rN' + Register indirect + +`@(D, rN)' +`@(D:16, rN)' +`@(D:24, rN)' + Register indirect: 16-bit or 24-bit displacement D from register + N. (24-bit displacements are only meaningful on the H8/300H.) + +`@rN+' + Register indirect with post-increment + +`@-rN' + Register indirect with pre-decrement + +``@'AA' +``@'AA:8' +``@'AA:16' +``@'AA:24' + Absolute address `aa'. (The address size `:24' only makes sense + on the H8/300H.) + +`#XX' +`#XX:8' +`#XX:16' +`#XX:32' + Immediate data XX. You may specify the `:8', `:16', or `:32' for + clarity, if you wish; but `as' neither requires this nor uses + it--the data size required is taken from context. + +``@'`@'AA' +``@'`@'AA:8' + Memory indirect. You may specify the `:8' for clarity, if you + wish; but `as' neither requires this nor uses it. + + +File: as.info, Node: H8/300 Floating Point, Next: H8/300 Directives, Prev: H8/300 Syntax, Up: H8/300-Dependent + +9.10.3 Floating Point +--------------------- + +The H8/300 family has no hardware floating point, but the `.float' +directive generates IEEE floating-point numbers for compatibility with +other development tools. + + +File: as.info, Node: H8/300 Directives, Next: H8/300 Opcodes, Prev: H8/300 Floating Point, Up: H8/300-Dependent + +9.10.4 H8/300 Machine Directives +-------------------------------- + +`as' has the following machine-dependent directives for the H8/300: + +`.h8300h' + Recognize and emit additional instructions for the H8/300H + variant, and also make `.int' emit 32-bit numbers rather than the + usual (16-bit) for the H8/300 family. + +`.h8300s' + Recognize and emit additional instructions for the H8S variant, and + also make `.int' emit 32-bit numbers rather than the usual (16-bit) + for the H8/300 family. + +`.h8300hn' + Recognize and emit additional instructions for the H8/300H variant + in normal mode, and also make `.int' emit 32-bit numbers rather + than the usual (16-bit) for the H8/300 family. + +`.h8300sn' + Recognize and emit additional instructions for the H8S variant in + normal mode, and also make `.int' emit 32-bit numbers rather than + the usual (16-bit) for the H8/300 family. + + On the H8/300 family (including the H8/300H) `.word' directives +generate 16-bit numbers. + + +File: as.info, Node: H8/300 Opcodes, Prev: H8/300 Directives, Up: H8/300-Dependent + +9.10.5 Opcodes +-------------- + +For detailed information on the H8/300 machine instruction set, see +`H8/300 Series Programming Manual'. For information specific to the +H8/300H, see `H8/300H Series Programming Manual' (Renesas). + + `as' implements all the standard H8/300 opcodes. No additional +pseudo-instructions are needed on this family. + + The following table summarizes the H8/300 opcodes, and their +arguments. Entries marked `*' are opcodes used only on the H8/300H. + + Legend: + Rs source register + Rd destination register + abs absolute address + imm immediate data + disp:N N-bit displacement from a register + pcrel:N N-bit displacement relative to program counter + + add.b #imm,rd * andc #imm,ccr + add.b rs,rd band #imm,rd + add.w rs,rd band #imm,@rd + * add.w #imm,rd band #imm,@abs:8 + * add.l rs,rd bra pcrel:8 + * add.l #imm,rd * bra pcrel:16 + adds #imm,rd bt pcrel:8 + addx #imm,rd * bt pcrel:16 + addx rs,rd brn pcrel:8 + and.b #imm,rd * brn pcrel:16 + and.b rs,rd bf pcrel:8 + * and.w rs,rd * bf pcrel:16 + * and.w #imm,rd bhi pcrel:8 + * and.l #imm,rd * bhi pcrel:16 + * and.l rs,rd bls pcrel:8 + + * bls pcrel:16 bld #imm,rd + bcc pcrel:8 bld #imm,@rd + * bcc pcrel:16 bld #imm,@abs:8 + bhs pcrel:8 bnot #imm,rd + * bhs pcrel:16 bnot #imm,@rd + bcs pcrel:8 bnot #imm,@abs:8 + * bcs pcrel:16 bnot rs,rd + blo pcrel:8 bnot rs,@rd + * blo pcrel:16 bnot rs,@abs:8 + bne pcrel:8 bor #imm,rd + * bne pcrel:16 bor #imm,@rd + beq pcrel:8 bor #imm,@abs:8 + * beq pcrel:16 bset #imm,rd + bvc pcrel:8 bset #imm,@rd + * bvc pcrel:16 bset #imm,@abs:8 + bvs pcrel:8 bset rs,rd + * bvs pcrel:16 bset rs,@rd + bpl pcrel:8 bset rs,@abs:8 + * bpl pcrel:16 bsr pcrel:8 + bmi pcrel:8 bsr pcrel:16 + * bmi pcrel:16 bst #imm,rd + bge pcrel:8 bst #imm,@rd + * bge pcrel:16 bst #imm,@abs:8 + blt pcrel:8 btst #imm,rd + * blt pcrel:16 btst #imm,@rd + bgt pcrel:8 btst #imm,@abs:8 + * bgt pcrel:16 btst rs,rd + ble pcrel:8 btst rs,@rd + * ble pcrel:16 btst rs,@abs:8 + bclr #imm,rd bxor #imm,rd + bclr #imm,@rd bxor #imm,@rd + bclr #imm,@abs:8 bxor #imm,@abs:8 + bclr rs,rd cmp.b #imm,rd + bclr rs,@rd cmp.b rs,rd + bclr rs,@abs:8 cmp.w rs,rd + biand #imm,rd cmp.w rs,rd + biand #imm,@rd * cmp.w #imm,rd + biand #imm,@abs:8 * cmp.l #imm,rd + bild #imm,rd * cmp.l rs,rd + bild #imm,@rd daa rs + bild #imm,@abs:8 das rs + bior #imm,rd dec.b rs + bior #imm,@rd * dec.w #imm,rd + bior #imm,@abs:8 * dec.l #imm,rd + bist #imm,rd divxu.b rs,rd + bist #imm,@rd * divxu.w rs,rd + bist #imm,@abs:8 * divxs.b rs,rd + bixor #imm,rd * divxs.w rs,rd + bixor #imm,@rd eepmov + bixor #imm,@abs:8 * eepmovw + + * exts.w rd mov.w rs,@abs:16 + * exts.l rd * mov.l #imm,rd + * extu.w rd * mov.l rs,rd + * extu.l rd * mov.l @rs,rd + inc rs * mov.l @(disp:16,rs),rd + * inc.w #imm,rd * mov.l @(disp:24,rs),rd + * inc.l #imm,rd * mov.l @rs+,rd + jmp @rs * mov.l @abs:16,rd + jmp abs * mov.l @abs:24,rd + jmp @@abs:8 * mov.l rs,@rd + jsr @rs * mov.l rs,@(disp:16,rd) + jsr abs * mov.l rs,@(disp:24,rd) + jsr @@abs:8 * mov.l rs,@-rd + ldc #imm,ccr * mov.l rs,@abs:16 + ldc rs,ccr * mov.l rs,@abs:24 + * ldc @abs:16,ccr movfpe @abs:16,rd + * ldc @abs:24,ccr movtpe rs,@abs:16 + * ldc @(disp:16,rs),ccr mulxu.b rs,rd + * ldc @(disp:24,rs),ccr * mulxu.w rs,rd + * ldc @rs+,ccr * mulxs.b rs,rd + * ldc @rs,ccr * mulxs.w rs,rd + * mov.b @(disp:24,rs),rd neg.b rs + * mov.b rs,@(disp:24,rd) * neg.w rs + mov.b @abs:16,rd * neg.l rs + mov.b rs,rd nop + mov.b @abs:8,rd not.b rs + mov.b rs,@abs:8 * not.w rs + mov.b rs,rd * not.l rs + mov.b #imm,rd or.b #imm,rd + mov.b @rs,rd or.b rs,rd + mov.b @(disp:16,rs),rd * or.w #imm,rd + mov.b @rs+,rd * or.w rs,rd + mov.b @abs:8,rd * or.l #imm,rd + mov.b rs,@rd * or.l rs,rd + mov.b rs,@(disp:16,rd) orc #imm,ccr + mov.b rs,@-rd pop.w rs + mov.b rs,@abs:8 * pop.l rs + mov.w rs,@rd push.w rs + * mov.w @(disp:24,rs),rd * push.l rs + * mov.w rs,@(disp:24,rd) rotl.b rs + * mov.w @abs:24,rd * rotl.w rs + * mov.w rs,@abs:24 * rotl.l rs + mov.w rs,rd rotr.b rs + mov.w #imm,rd * rotr.w rs + mov.w @rs,rd * rotr.l rs + mov.w @(disp:16,rs),rd rotxl.b rs + mov.w @rs+,rd * rotxl.w rs + mov.w @abs:16,rd * rotxl.l rs + mov.w rs,@(disp:16,rd) rotxr.b rs + mov.w rs,@-rd * rotxr.w rs + + * rotxr.l rs * stc ccr,@(disp:24,rd) + bpt * stc ccr,@-rd + rte * stc ccr,@abs:16 + rts * stc ccr,@abs:24 + shal.b rs sub.b rs,rd + * shal.w rs sub.w rs,rd + * shal.l rs * sub.w #imm,rd + shar.b rs * sub.l rs,rd + * shar.w rs * sub.l #imm,rd + * shar.l rs subs #imm,rd + shll.b rs subx #imm,rd + * shll.w rs subx rs,rd + * shll.l rs * trapa #imm + shlr.b rs xor #imm,rd + * shlr.w rs xor rs,rd + * shlr.l rs * xor.w #imm,rd + sleep * xor.w rs,rd + stc ccr,rd * xor.l #imm,rd + * stc ccr,@rs * xor.l rs,rd + * stc ccr,@(disp:16,rd) xorc #imm,ccr + + Four H8/300 instructions (`add', `cmp', `mov', `sub') are defined +with variants using the suffixes `.b', `.w', and `.l' to specify the +size of a memory operand. `as' supports these suffixes, but does not +require them; since one of the operands is always a register, `as' can +deduce the correct size. + + For example, since `r0' refers to a 16-bit register, + mov r0,@foo +is equivalent to + mov.w r0,@foo + + If you use the size suffixes, `as' issues a warning when the suffix +and the register size do not match. + + +File: as.info, Node: HPPA-Dependent, Next: ESA/390-Dependent, Prev: H8/300-Dependent, Up: Machine Dependencies + +9.11 HPPA Dependent Features +============================ + +* Menu: + +* HPPA Notes:: Notes +* HPPA Options:: Options +* HPPA Syntax:: Syntax +* HPPA Floating Point:: Floating Point +* HPPA Directives:: HPPA Machine Directives +* HPPA Opcodes:: Opcodes + + +File: as.info, Node: HPPA Notes, Next: HPPA Options, Up: HPPA-Dependent + +9.11.1 Notes +------------ + +As a back end for GNU CC `as' has been throughly tested and should work +extremely well. We have tested it only minimally on hand written +assembly code and no one has tested it much on the assembly output from +the HP compilers. + + The format of the debugging sections has changed since the original +`as' port (version 1.3X) was released; therefore, you must rebuild all +HPPA objects and libraries with the new assembler so that you can debug +the final executable. + + The HPPA `as' port generates a small subset of the relocations +available in the SOM and ELF object file formats. Additional relocation +support will be added as it becomes necessary. + + +File: as.info, Node: HPPA Options, Next: HPPA Syntax, Prev: HPPA Notes, Up: HPPA-Dependent + +9.11.2 Options +-------------- + +`as' has no machine-dependent command-line options for the HPPA. + + +File: as.info, Node: HPPA Syntax, Next: HPPA Floating Point, Prev: HPPA Options, Up: HPPA-Dependent + +9.11.3 Syntax +------------- + +The assembler syntax closely follows the HPPA instruction set reference +manual; assembler directives and general syntax closely follow the HPPA +assembly language reference manual, with a few noteworthy differences. + + First, a colon may immediately follow a label definition. This is +simply for compatibility with how most assembly language programmers +write code. + + Some obscure expression parsing problems may affect hand written +code which uses the `spop' instructions, or code which makes significant +use of the `!' line separator. + + `as' is much less forgiving about missing arguments and other +similar oversights than the HP assembler. `as' notifies you of missing +arguments as syntax errors; this is regarded as a feature, not a bug. + + Finally, `as' allows you to use an external symbol without +explicitly importing the symbol. _Warning:_ in the future this will be +an error for HPPA targets. + + Special characters for HPPA targets include: + + `;' is the line comment character. + + `!' can be used instead of a newline to separate statements. + + Since `$' has no special meaning, you may use it in symbol names. + + +File: as.info, Node: HPPA Floating Point, Next: HPPA Directives, Prev: HPPA Syntax, Up: HPPA-Dependent + +9.11.4 Floating Point +--------------------- + +The HPPA family uses IEEE floating-point numbers. + + +File: as.info, Node: HPPA Directives, Next: HPPA Opcodes, Prev: HPPA Floating Point, Up: HPPA-Dependent + +9.11.5 HPPA Assembler Directives +-------------------------------- + +`as' for the HPPA supports many additional directives for compatibility +with the native assembler. This section describes them only briefly. +For detailed information on HPPA-specific assembler directives, see +`HP9000 Series 800 Assembly Language Reference Manual' (HP 92432-90001). + + `as' does _not_ support the following assembler directives described +in the HP manual: + + .endm .liston + .enter .locct + .leave .macro + .listoff + + Beyond those implemented for compatibility, `as' supports one +additional assembler directive for the HPPA: `.param'. It conveys +register argument locations for static functions. Its syntax closely +follows the `.export' directive. + + These are the additional directives in `as' for the HPPA: + +`.block N' +`.blockz N' + Reserve N bytes of storage, and initialize them to zero. + +`.call' + Mark the beginning of a procedure call. Only the special case + with _no arguments_ is allowed. + +`.callinfo [ PARAM=VALUE, ... ] [ FLAG, ... ]' + Specify a number of parameters and flags that define the + environment for a procedure. + + PARAM may be any of `frame' (frame size), `entry_gr' (end of + general register range), `entry_fr' (end of float register range), + `entry_sr' (end of space register range). + + The values for FLAG are `calls' or `caller' (proc has + subroutines), `no_calls' (proc does not call subroutines), + `save_rp' (preserve return pointer), `save_sp' (proc preserves + stack pointer), `no_unwind' (do not unwind this proc), `hpux_int' + (proc is interrupt routine). + +`.code' + Assemble into the standard section called `$TEXT$', subsection + `$CODE$'. + +`.copyright "STRING"' + In the SOM object format, insert STRING into the object code, + marked as a copyright string. + +`.copyright "STRING"' + In the ELF object format, insert STRING into the object code, + marked as a version string. + +`.enter' + Not yet supported; the assembler rejects programs containing this + directive. + +`.entry' + Mark the beginning of a procedure. + +`.exit' + Mark the end of a procedure. + +`.export NAME [ ,TYP ] [ ,PARAM=R ]' + Make a procedure NAME available to callers. TYP, if present, must + be one of `absolute', `code' (ELF only, not SOM), `data', `entry', + `data', `entry', `millicode', `plabel', `pri_prog', or `sec_prog'. + + PARAM, if present, provides either relocation information for the + procedure arguments and result, or a privilege level. PARAM may be + `argwN' (where N ranges from `0' to `3', and indicates one of four + one-word arguments); `rtnval' (the procedure's result); or + `priv_lev' (privilege level). For arguments or the result, R + specifies how to relocate, and must be one of `no' (not + relocatable), `gr' (argument is in general register), `fr' (in + floating point register), or `fu' (upper half of float register). + For `priv_lev', R is an integer. + +`.half N' + Define a two-byte integer constant N; synonym for the portable + `as' directive `.short'. + +`.import NAME [ ,TYP ]' + Converse of `.export'; make a procedure available to call. The + arguments use the same conventions as the first two arguments for + `.export'. + +`.label NAME' + Define NAME as a label for the current assembly location. + +`.leave' + Not yet supported; the assembler rejects programs containing this + directive. + +`.origin LC' + Advance location counter to LC. Synonym for the `as' portable + directive `.org'. + +`.param NAME [ ,TYP ] [ ,PARAM=R ]' + Similar to `.export', but used for static procedures. + +`.proc' + Use preceding the first statement of a procedure. + +`.procend' + Use following the last statement of a procedure. + +`LABEL .reg EXPR' + Synonym for `.equ'; define LABEL with the absolute expression EXPR + as its value. + +`.space SECNAME [ ,PARAMS ]' + Switch to section SECNAME, creating a new section by that name if + necessary. You may only use PARAMS when creating a new section, + not when switching to an existing one. SECNAME may identify a + section by number rather than by name. + + If specified, the list PARAMS declares attributes of the section, + identified by keywords. The keywords recognized are `spnum=EXP' + (identify this section by the number EXP, an absolute expression), + `sort=EXP' (order sections according to this sort key when linking; + EXP is an absolute expression), `unloadable' (section contains no + loadable data), `notdefined' (this section defined elsewhere), and + `private' (data in this section not available to other programs). + +`.spnum SECNAM' + Allocate four bytes of storage, and initialize them with the + section number of the section named SECNAM. (You can define the + section number with the HPPA `.space' directive.) + +`.string "STR"' + Copy the characters in the string STR to the object file. *Note + Strings: Strings, for information on escape sequences you can use + in `as' strings. + + _Warning!_ The HPPA version of `.string' differs from the usual + `as' definition: it does _not_ write a zero byte after copying STR. + +`.stringz "STR"' + Like `.string', but appends a zero byte after copying STR to object + file. + +`.subspa NAME [ ,PARAMS ]' +`.nsubspa NAME [ ,PARAMS ]' + Similar to `.space', but selects a subsection NAME within the + current section. You may only specify PARAMS when you create a + subsection (in the first instance of `.subspa' for this NAME). + + If specified, the list PARAMS declares attributes of the + subsection, identified by keywords. The keywords recognized are + `quad=EXPR' ("quadrant" for this subsection), `align=EXPR' + (alignment for beginning of this subsection; a power of two), + `access=EXPR' (value for "access rights" field), `sort=EXPR' + (sorting order for this subspace in link), `code_only' (subsection + contains only code), `unloadable' (subsection cannot be loaded + into memory), `comdat' (subsection is comdat), `common' + (subsection is common block), `dup_comm' (subsection may have + duplicate names), or `zero' (subsection is all zeros, do not write + in object file). + + `.nsubspa' always creates a new subspace with the given name, even + if one with the same name already exists. + + `comdat', `common' and `dup_comm' can be used to implement various + flavors of one-only support when using the SOM linker. The SOM + linker only supports specific combinations of these flags. The + details are not documented. A brief description is provided here. + + `comdat' provides a form of linkonce support. It is useful for + both code and data subspaces. A `comdat' subspace has a key symbol + marked by the `is_comdat' flag or `ST_COMDAT'. Only the first + subspace for any given key is selected. The key symbol becomes + universal in shared links. This is similar to the behavior of + `secondary_def' symbols. + + `common' provides Fortran named common support. It is only useful + for data subspaces. Symbols with the flag `is_common' retain this + flag in shared links. Referencing a `is_common' symbol in a shared + library from outside the library doesn't work. Thus, `is_common' + symbols must be output whenever they are needed. + + `common' and `dup_comm' together provide Cobol common support. + The subspaces in this case must all be the same length. + Otherwise, this support is similar to the Fortran common support. + + `dup_comm' by itself provides a type of one-only support for code. + Only the first `dup_comm' subspace is selected. There is a rather + complex algorithm to compare subspaces. Code symbols marked with + the `dup_common' flag are hidden. This support was intended for + "C++ duplicate inlines". + + A simplified technique is used to mark the flags of symbols based + on the flags of their subspace. A symbol with the scope + SS_UNIVERSAL and type ST_ENTRY, ST_CODE or ST_DATA is marked with + the corresponding settings of `comdat', `common' and `dup_comm' + from the subspace, respectively. This avoids having to introduce + additional directives to mark these symbols. The HP assembler + sets `is_common' from `common'. However, it doesn't set the + `dup_common' from `dup_comm'. It doesn't have `comdat' support. + +`.version "STR"' + Write STR as version identifier in object code. + + +File: as.info, Node: HPPA Opcodes, Prev: HPPA Directives, Up: HPPA-Dependent + +9.11.6 Opcodes +-------------- + +For detailed information on the HPPA machine instruction set, see +`PA-RISC Architecture and Instruction Set Reference Manual' (HP +09740-90039). + + +File: as.info, Node: ESA/390-Dependent, Next: i386-Dependent, Prev: HPPA-Dependent, Up: Machine Dependencies + +9.12 ESA/390 Dependent Features +=============================== + +* Menu: + +* ESA/390 Notes:: Notes +* ESA/390 Options:: Options +* ESA/390 Syntax:: Syntax +* ESA/390 Floating Point:: Floating Point +* ESA/390 Directives:: ESA/390 Machine Directives +* ESA/390 Opcodes:: Opcodes + + +File: as.info, Node: ESA/390 Notes, Next: ESA/390 Options, Up: ESA/390-Dependent + +9.12.1 Notes +------------ + +The ESA/390 `as' port is currently intended to be a back-end for the +GNU CC compiler. It is not HLASM compatible, although it does support +a subset of some of the HLASM directives. The only supported binary +file format is ELF; none of the usual MVS/VM/OE/USS object file +formats, such as ESD or XSD, are supported. + + When used with the GNU CC compiler, the ESA/390 `as' will produce +correct, fully relocated, functional binaries, and has been used to +compile and execute large projects. However, many aspects should still +be considered experimental; these include shared library support, +dynamically loadable objects, and any relocation other than the 31-bit +relocation. + + +File: as.info, Node: ESA/390 Options, Next: ESA/390 Syntax, Prev: ESA/390 Notes, Up: ESA/390-Dependent + +9.12.2 Options +-------------- + +`as' has no machine-dependent command-line options for the ESA/390. + + +File: as.info, Node: ESA/390 Syntax, Next: ESA/390 Floating Point, Prev: ESA/390 Options, Up: ESA/390-Dependent + +9.12.3 Syntax +------------- + +The opcode/operand syntax follows the ESA/390 Principles of Operation +manual; assembler directives and general syntax are loosely based on the +prevailing AT&T/SVR4/ELF/Solaris style notation. HLASM-style directives +are _not_ supported for the most part, with the exception of those +described herein. + + A leading dot in front of directives is optional, and the case of +directives is ignored; thus for example, .using and USING have the same +effect. + + A colon may immediately follow a label definition. This is simply +for compatibility with how most assembly language programmers write +code. + + `#' is the line comment character. + + `;' can be used instead of a newline to separate statements. + + Since `$' has no special meaning, you may use it in symbol names. + + Registers can be given the symbolic names r0..r15, fp0, fp2, fp4, +fp6. By using thesse symbolic names, `as' can detect simple syntax +errors. The name rarg or r.arg is a synonym for r11, rtca or r.tca for +r12, sp, r.sp, dsa r.dsa for r13, lr or r.lr for r14, rbase or r.base +for r3 and rpgt or r.pgt for r4. + + `*' is the current location counter. Unlike `.' it is always +relative to the last USING directive. Note that this means that +expressions cannot use multiplication, as any occurrence of `*' will be +interpreted as a location counter. + + All labels are relative to the last USING. Thus, branches to a label +always imply the use of base+displacement. + + Many of the usual forms of address constants / address literals are +supported. Thus, + .using *,r3 + L r15,=A(some_routine) + LM r6,r7,=V(some_longlong_extern) + A r1,=F'12' + AH r0,=H'42' + ME r6,=E'3.1416' + MD r6,=D'3.14159265358979' + O r6,=XL4'cacad0d0' + .ltorg + should all behave as expected: that is, an entry in the literal pool +will be created (or reused if it already exists), and the instruction +operands will be the displacement into the literal pool using the +current base register (as last declared with the `.using' directive). + + +File: as.info, Node: ESA/390 Floating Point, Next: ESA/390 Directives, Prev: ESA/390 Syntax, Up: ESA/390-Dependent + +9.12.4 Floating Point +--------------------- + +The assembler generates only IEEE floating-point numbers. The older +floating point formats are not supported. + + +File: as.info, Node: ESA/390 Directives, Next: ESA/390 Opcodes, Prev: ESA/390 Floating Point, Up: ESA/390-Dependent + +9.12.5 ESA/390 Assembler Directives +----------------------------------- + +`as' for the ESA/390 supports all of the standard ELF/SVR4 assembler +directives that are documented in the main part of this documentation. +Several additional directives are supported in order to implement the +ESA/390 addressing model. The most important of these are `.using' and +`.ltorg' + + These are the additional directives in `as' for the ESA/390: + +`.dc' + A small subset of the usual DC directive is supported. + +`.drop REGNO' + Stop using REGNO as the base register. The REGNO must have been + previously declared with a `.using' directive in the same section + as the current section. + +`.ebcdic STRING' + Emit the EBCDIC equivalent of the indicated string. The emitted + string will be null terminated. Note that the directives + `.string' etc. emit ascii strings by default. + +`EQU' + The standard HLASM-style EQU directive is not supported; however, + the standard `as' directive .equ can be used to the same effect. + +`.ltorg' + Dump the literal pool accumulated so far; begin a new literal pool. + The literal pool will be written in the current section; in order + to generate correct assembly, a `.using' must have been previously + specified in the same section. + +`.using EXPR,REGNO' + Use REGNO as the base register for all subsequent RX, RS, and SS + form instructions. The EXPR will be evaluated to obtain the base + address; usually, EXPR will merely be `*'. + + This assembler allows two `.using' directives to be simultaneously + outstanding, one in the `.text' section, and one in another section + (typically, the `.data' section). This feature allows dynamically + loaded objects to be implemented in a relatively straightforward + way. A `.using' directive must always be specified in the `.text' + section; this will specify the base register that will be used for + branches in the `.text' section. A second `.using' may be + specified in another section; this will specify the base register + that is used for non-label address literals. When a second + `.using' is specified, then the subsequent `.ltorg' must be put in + the same section; otherwise an error will result. + + Thus, for example, the following code uses `r3' to address branch + targets and `r4' to address the literal pool, which has been + written to the `.data' section. The is, the constants + `=A(some_routine)', `=H'42'' and `=E'3.1416'' will all appear in + the `.data' section. + + .data + .using LITPOOL,r4 + .text + BASR r3,0 + .using *,r3 + B START + .long LITPOOL + START: + L r4,4(,r3) + L r15,=A(some_routine) + LTR r15,r15 + BNE LABEL + AH r0,=H'42' + LABEL: + ME r6,=E'3.1416' + .data + LITPOOL: + .ltorg + + Note that this dual-`.using' directive semantics extends and is + not compatible with HLASM semantics. Note that this assembler + directive does not support the full range of HLASM semantics. + + + +File: as.info, Node: ESA/390 Opcodes, Prev: ESA/390 Directives, Up: ESA/390-Dependent + +9.12.6 Opcodes +-------------- + +For detailed information on the ESA/390 machine instruction set, see +`ESA/390 Principles of Operation' (IBM Publication Number DZ9AR004). + + +File: as.info, Node: i386-Dependent, Next: i860-Dependent, Prev: ESA/390-Dependent, Up: Machine Dependencies + +9.13 80386 Dependent Features +============================= + + The i386 version `as' supports both the original Intel 386 +architecture in both 16 and 32-bit mode as well as AMD x86-64 +architecture extending the Intel architecture to 64-bits. + +* Menu: + +* i386-Options:: Options +* i386-Directives:: X86 specific directives +* i386-Syntax:: AT&T Syntax versus Intel Syntax +* i386-Mnemonics:: Instruction Naming +* i386-Regs:: Register Naming +* i386-Prefixes:: Instruction Prefixes +* i386-Memory:: Memory References +* i386-Jumps:: Handling of Jump Instructions +* i386-Float:: Floating Point +* i386-SIMD:: Intel's MMX and AMD's 3DNow! SIMD Operations +* i386-16bit:: Writing 16-bit Code +* i386-Arch:: Specifying an x86 CPU architecture +* i386-Bugs:: AT&T Syntax bugs +* i386-Notes:: Notes + + +File: as.info, Node: i386-Options, Next: i386-Directives, Up: i386-Dependent + +9.13.1 Options +-------------- + +The i386 version of `as' has a few machine dependent options: + +`--32 | --64' + Select the word size, either 32 bits or 64 bits. Selecting 32-bit + implies Intel i386 architecture, while 64-bit implies AMD x86-64 + architecture. + + These options are only available with the ELF object file format, + and require that the necessary BFD support has been included (on a + 32-bit platform you have to add -enable-64-bit-bfd to configure + enable 64-bit usage and use x86-64 as target platform). + +`-n' + By default, x86 GAS replaces multiple nop instructions used for + alignment within code sections with multi-byte nop instructions + such as leal 0(%esi,1),%esi. This switch disables the + optimization. + +`--divide' + On SVR4-derived platforms, the character `/' is treated as a + comment character, which means that it cannot be used in + expressions. The `--divide' option turns `/' into a normal + character. This does not disable `/' at the beginning of a line + starting a comment, or affect using `#' for starting a comment. + +`-march=CPU[+EXTENSION...]' + This option specifies the target processor. The assembler will + issue an error message if an attempt is made to assemble an + instruction which will not execute on the target processor. The + following processor names are recognized: `i8086', `i186', `i286', + `i386', `i486', `i586', `i686', `pentium', `pentiumpro', + `pentiumii', `pentiumiii', `pentium4', `prescott', `nocona', + `core', `core2', `corei7', `l1om', `k6', `k6_2', `athlon', + `opteron', `k8', `amdfam10', `generic32' and `generic64'. + + In addition to the basic instruction set, the assembler can be + told to accept various extension mnemonics. For example, + `-march=i686+sse4+vmx' extends I686 with SSE4 and VMX. The + following extensions are currently supported: `8087', `287', `387', + `no87', `mmx', `nommx', `sse', `sse2', `sse3', `ssse3', `sse4.1', + `sse4.2', `sse4', `nosse', `avx', `noavx', `vmx', `smx', `xsave', + `aes', `pclmul', `fma', `movbe', `ept', `clflush', `syscall', + `rdtscp', `3dnow', `3dnowa', `sse4a', `sse5', `svme', `abm' and + `padlock'. Note that rather than extending a basic instruction + set, the extension mnemonics starting with `no' revoke the + respective functionality. + + When the `.arch' directive is used with `-march', the `.arch' + directive will take precedent. + +`-mtune=CPU' + This option specifies a processor to optimize for. When used in + conjunction with the `-march' option, only instructions of the + processor specified by the `-march' option will be generated. + + Valid CPU values are identical to the processor list of + `-march=CPU'. + +`-msse2avx' + This option specifies that the assembler should encode SSE + instructions with VEX prefix. + +`-msse-check=NONE' + +`-msse-check=WARNING' + +`-msse-check=ERROR' + These options control if the assembler should check SSE + intructions. `-msse-check=NONE' will make the assembler not to + check SSE instructions, which is the default. + `-msse-check=WARNING' will make the assembler issue a warning for + any SSE intruction. `-msse-check=ERROR' will make the assembler + issue an error for any SSE intruction. + +`-mmnemonic=ATT' + +`-mmnemonic=INTEL' + This option specifies instruction mnemonic for matching + instructions. The `.att_mnemonic' and `.intel_mnemonic' + directives will take precedent. + +`-msyntax=ATT' + +`-msyntax=INTEL' + This option specifies instruction syntax when processing + instructions. The `.att_syntax' and `.intel_syntax' directives + will take precedent. + +`-mnaked-reg' + This opetion specifies that registers don't require a `%' prefix. + The `.att_syntax' and `.intel_syntax' directives will take + precedent. + + + +File: as.info, Node: i386-Directives, Next: i386-Syntax, Prev: i386-Options, Up: i386-Dependent + +9.13.2 x86 specific Directives +------------------------------ + +`.lcomm SYMBOL , LENGTH[, ALIGNMENT]' + Reserve LENGTH (an absolute expression) bytes for a local common + denoted by SYMBOL. The section and value of SYMBOL are those of + the new local common. The addresses are allocated in the bss + section, so that at run-time the bytes start off zeroed. Since + SYMBOL is not declared global, it is normally not visible to `ld'. + The optional third parameter, ALIGNMENT, specifies the desired + alignment of the symbol in the bss section. + + This directive is only available for COFF based x86 targets. + + + +File: as.info, Node: i386-Syntax, Next: i386-Mnemonics, Prev: i386-Directives, Up: i386-Dependent + +9.13.3 AT&T Syntax versus Intel Syntax +-------------------------------------- + +`as' now supports assembly using Intel assembler syntax. +`.intel_syntax' selects Intel mode, and `.att_syntax' switches back to +the usual AT&T mode for compatibility with the output of `gcc'. Either +of these directives may have an optional argument, `prefix', or +`noprefix' specifying whether registers require a `%' prefix. AT&T +System V/386 assembler syntax is quite different from Intel syntax. We +mention these differences because almost all 80386 documents use Intel +syntax. Notable differences between the two syntaxes are: + + * AT&T immediate operands are preceded by `$'; Intel immediate + operands are undelimited (Intel `push 4' is AT&T `pushl $4'). + AT&T register operands are preceded by `%'; Intel register operands + are undelimited. AT&T absolute (as opposed to PC relative) + jump/call operands are prefixed by `*'; they are undelimited in + Intel syntax. + + * AT&T and Intel syntax use the opposite order for source and + destination operands. Intel `add eax, 4' is `addl $4, %eax'. The + `source, dest' convention is maintained for compatibility with + previous Unix assemblers. Note that `bound', `invlpga', and + instructions with 2 immediate operands, such as the `enter' + instruction, do _not_ have reversed order. *Note i386-Bugs::. + + * In AT&T syntax the size of memory operands is determined from the + last character of the instruction mnemonic. Mnemonic suffixes of + `b', `w', `l' and `q' specify byte (8-bit), word (16-bit), long + (32-bit) and quadruple word (64-bit) memory references. Intel + syntax accomplishes this by prefixing memory operands (_not_ the + instruction mnemonics) with `byte ptr', `word ptr', `dword ptr' + and `qword ptr'. Thus, Intel `mov al, byte ptr FOO' is `movb FOO, + %al' in AT&T syntax. + + * Immediate form long jumps and calls are `lcall/ljmp $SECTION, + $OFFSET' in AT&T syntax; the Intel syntax is `call/jmp far + SECTION:OFFSET'. Also, the far return instruction is `lret + $STACK-ADJUST' in AT&T syntax; Intel syntax is `ret far + STACK-ADJUST'. + + * The AT&T assembler does not provide support for multiple section + programs. Unix style systems expect all programs to be single + sections. + + +File: as.info, Node: i386-Mnemonics, Next: i386-Regs, Prev: i386-Syntax, Up: i386-Dependent + +9.13.4 Instruction Naming +------------------------- + +Instruction mnemonics are suffixed with one character modifiers which +specify the size of operands. The letters `b', `w', `l' and `q' +specify byte, word, long and quadruple word operands. If no suffix is +specified by an instruction then `as' tries to fill in the missing +suffix based on the destination register operand (the last one by +convention). Thus, `mov %ax, %bx' is equivalent to `movw %ax, %bx'; +also, `mov $1, %bx' is equivalent to `movw $1, bx'. Note that this is +incompatible with the AT&T Unix assembler which assumes that a missing +mnemonic suffix implies long operand size. (This incompatibility does +not affect compiler output since compilers always explicitly specify +the mnemonic suffix.) + + Almost all instructions have the same names in AT&T and Intel format. +There are a few exceptions. The sign extend and zero extend +instructions need two sizes to specify them. They need a size to +sign/zero extend _from_ and a size to zero extend _to_. This is +accomplished by using two instruction mnemonic suffixes in AT&T syntax. +Base names for sign extend and zero extend are `movs...' and `movz...' +in AT&T syntax (`movsx' and `movzx' in Intel syntax). The instruction +mnemonic suffixes are tacked on to this base name, the _from_ suffix +before the _to_ suffix. Thus, `movsbl %al, %edx' is AT&T syntax for +"move sign extend _from_ %al _to_ %edx." Possible suffixes, thus, are +`bl' (from byte to long), `bw' (from byte to word), `wl' (from word to +long), `bq' (from byte to quadruple word), `wq' (from word to quadruple +word), and `lq' (from long to quadruple word). + + Different encoding options can be specified via optional mnemonic +suffix. `.s' suffix swaps 2 register operands in encoding when moving +from one register to another. + + The Intel-syntax conversion instructions + + * `cbw' -- sign-extend byte in `%al' to word in `%ax', + + * `cwde' -- sign-extend word in `%ax' to long in `%eax', + + * `cwd' -- sign-extend word in `%ax' to long in `%dx:%ax', + + * `cdq' -- sign-extend dword in `%eax' to quad in `%edx:%eax', + + * `cdqe' -- sign-extend dword in `%eax' to quad in `%rax' (x86-64 + only), + + * `cqo' -- sign-extend quad in `%rax' to octuple in `%rdx:%rax' + (x86-64 only), + +are called `cbtw', `cwtl', `cwtd', `cltd', `cltq', and `cqto' in AT&T +naming. `as' accepts either naming for these instructions. + + Far call/jump instructions are `lcall' and `ljmp' in AT&T syntax, +but are `call far' and `jump far' in Intel convention. + +9.13.5 AT&T Mnemonic versus Intel Mnemonic +------------------------------------------ + +`as' supports assembly using Intel mnemonic. `.intel_mnemonic' selects +Intel mnemonic with Intel syntax, and `.att_mnemonic' switches back to +the usual AT&T mnemonic with AT&T syntax for compatibility with the +output of `gcc'. Several x87 instructions, `fadd', `fdiv', `fdivp', +`fdivr', `fdivrp', `fmul', `fsub', `fsubp', `fsubr' and `fsubrp', are +implemented in AT&T System V/386 assembler with different mnemonics +from those in Intel IA32 specification. `gcc' generates those +instructions with AT&T mnemonic. + + +File: as.info, Node: i386-Regs, Next: i386-Prefixes, Prev: i386-Mnemonics, Up: i386-Dependent + +9.13.6 Register Naming +---------------------- + +Register operands are always prefixed with `%'. The 80386 registers +consist of + + * the 8 32-bit registers `%eax' (the accumulator), `%ebx', `%ecx', + `%edx', `%edi', `%esi', `%ebp' (the frame pointer), and `%esp' + (the stack pointer). + + * the 8 16-bit low-ends of these: `%ax', `%bx', `%cx', `%dx', `%di', + `%si', `%bp', and `%sp'. + + * the 8 8-bit registers: `%ah', `%al', `%bh', `%bl', `%ch', `%cl', + `%dh', and `%dl' (These are the high-bytes and low-bytes of `%ax', + `%bx', `%cx', and `%dx') + + * the 6 section registers `%cs' (code section), `%ds' (data + section), `%ss' (stack section), `%es', `%fs', and `%gs'. + + * the 3 processor control registers `%cr0', `%cr2', and `%cr3'. + + * the 6 debug registers `%db0', `%db1', `%db2', `%db3', `%db6', and + `%db7'. + + * the 2 test registers `%tr6' and `%tr7'. + + * the 8 floating point register stack `%st' or equivalently + `%st(0)', `%st(1)', `%st(2)', `%st(3)', `%st(4)', `%st(5)', + `%st(6)', and `%st(7)'. These registers are overloaded by 8 MMX + registers `%mm0', `%mm1', `%mm2', `%mm3', `%mm4', `%mm5', `%mm6' + and `%mm7'. + + * the 8 SSE registers registers `%xmm0', `%xmm1', `%xmm2', `%xmm3', + `%xmm4', `%xmm5', `%xmm6' and `%xmm7'. + + The AMD x86-64 architecture extends the register set by: + + * enhancing the 8 32-bit registers to 64-bit: `%rax' (the + accumulator), `%rbx', `%rcx', `%rdx', `%rdi', `%rsi', `%rbp' (the + frame pointer), `%rsp' (the stack pointer) + + * the 8 extended registers `%r8'-`%r15'. + + * the 8 32-bit low ends of the extended registers: `%r8d'-`%r15d' + + * the 8 16-bit low ends of the extended registers: `%r8w'-`%r15w' + + * the 8 8-bit low ends of the extended registers: `%r8b'-`%r15b' + + * the 4 8-bit registers: `%sil', `%dil', `%bpl', `%spl'. + + * the 8 debug registers: `%db8'-`%db15'. + + * the 8 SSE registers: `%xmm8'-`%xmm15'. + + +File: as.info, Node: i386-Prefixes, Next: i386-Memory, Prev: i386-Regs, Up: i386-Dependent + +9.13.7 Instruction Prefixes +--------------------------- + +Instruction prefixes are used to modify the following instruction. They +are used to repeat string instructions, to provide section overrides, to +perform bus lock operations, and to change operand and address sizes. +(Most instructions that normally operate on 32-bit operands will use +16-bit operands if the instruction has an "operand size" prefix.) +Instruction prefixes are best written on the same line as the +instruction they act upon. For example, the `scas' (scan string) +instruction is repeated with: + + repne scas %es:(%edi),%al + + You may also place prefixes on the lines immediately preceding the +instruction, but this circumvents checks that `as' does with prefixes, +and will not work with all prefixes. + + Here is a list of instruction prefixes: + + * Section override prefixes `cs', `ds', `ss', `es', `fs', `gs'. + These are automatically added by specifying using the + SECTION:MEMORY-OPERAND form for memory references. + + * Operand/Address size prefixes `data16' and `addr16' change 32-bit + operands/addresses into 16-bit operands/addresses, while `data32' + and `addr32' change 16-bit ones (in a `.code16' section) into + 32-bit operands/addresses. These prefixes _must_ appear on the + same line of code as the instruction they modify. For example, in + a 16-bit `.code16' section, you might write: + + addr32 jmpl *(%ebx) + + * The bus lock prefix `lock' inhibits interrupts during execution of + the instruction it precedes. (This is only valid with certain + instructions; see a 80386 manual for details). + + * The wait for coprocessor prefix `wait' waits for the coprocessor to + complete the current instruction. This should never be needed for + the 80386/80387 combination. + + * The `rep', `repe', and `repne' prefixes are added to string + instructions to make them repeat `%ecx' times (`%cx' times if the + current address size is 16-bits). + + * The `rex' family of prefixes is used by x86-64 to encode + extensions to i386 instruction set. The `rex' prefix has four + bits -- an operand size overwrite (`64') used to change operand + size from 32-bit to 64-bit and X, Y and Z extensions bits used to + extend the register set. + + You may write the `rex' prefixes directly. The `rex64xyz' + instruction emits `rex' prefix with all the bits set. By omitting + the `64', `x', `y' or `z' you may write other prefixes as well. + Normally, there is no need to write the prefixes explicitly, since + gas will automatically generate them based on the instruction + operands. + + +File: as.info, Node: i386-Memory, Next: i386-Jumps, Prev: i386-Prefixes, Up: i386-Dependent + +9.13.8 Memory References +------------------------ + +An Intel syntax indirect memory reference of the form + + SECTION:[BASE + INDEX*SCALE + DISP] + +is translated into the AT&T syntax + + SECTION:DISP(BASE, INDEX, SCALE) + +where BASE and INDEX are the optional 32-bit base and index registers, +DISP is the optional displacement, and SCALE, taking the values 1, 2, +4, and 8, multiplies INDEX to calculate the address of the operand. If +no SCALE is specified, SCALE is taken to be 1. SECTION specifies the +optional section register for the memory operand, and may override the +default section register (see a 80386 manual for section register +defaults). Note that section overrides in AT&T syntax _must_ be +preceded by a `%'. If you specify a section override which coincides +with the default section register, `as' does _not_ output any section +register override prefixes to assemble the given instruction. Thus, +section overrides can be specified to emphasize which section register +is used for a given memory operand. + + Here are some examples of Intel and AT&T style memory references: + +AT&T: `-4(%ebp)', Intel: `[ebp - 4]' + BASE is `%ebp'; DISP is `-4'. SECTION is missing, and the default + section is used (`%ss' for addressing with `%ebp' as the base + register). INDEX, SCALE are both missing. + +AT&T: `foo(,%eax,4)', Intel: `[foo + eax*4]' + INDEX is `%eax' (scaled by a SCALE 4); DISP is `foo'. All other + fields are missing. The section register here defaults to `%ds'. + +AT&T: `foo(,1)'; Intel `[foo]' + This uses the value pointed to by `foo' as a memory operand. Note + that BASE and INDEX are both missing, but there is only _one_ `,'. + This is a syntactic exception. + +AT&T: `%gs:foo'; Intel `gs:foo' + This selects the contents of the variable `foo' with section + register SECTION being `%gs'. + + Absolute (as opposed to PC relative) call and jump operands must be +prefixed with `*'. If no `*' is specified, `as' always chooses PC +relative addressing for jump/call labels. + + Any instruction that has a memory operand, but no register operand, +_must_ specify its size (byte, word, long, or quadruple) with an +instruction mnemonic suffix (`b', `w', `l' or `q', respectively). + + The x86-64 architecture adds an RIP (instruction pointer relative) +addressing. This addressing mode is specified by using `rip' as a base +register. Only constant offsets are valid. For example: + +AT&T: `1234(%rip)', Intel: `[rip + 1234]' + Points to the address 1234 bytes past the end of the current + instruction. + +AT&T: `symbol(%rip)', Intel: `[rip + symbol]' + Points to the `symbol' in RIP relative way, this is shorter than + the default absolute addressing. + + Other addressing modes remain unchanged in x86-64 architecture, +except registers used are 64-bit instead of 32-bit. + + +File: as.info, Node: i386-Jumps, Next: i386-Float, Prev: i386-Memory, Up: i386-Dependent + +9.13.9 Handling of Jump Instructions +------------------------------------ + +Jump instructions are always optimized to use the smallest possible +displacements. This is accomplished by using byte (8-bit) displacement +jumps whenever the target is sufficiently close. If a byte displacement +is insufficient a long displacement is used. We do not support word +(16-bit) displacement jumps in 32-bit mode (i.e. prefixing the jump +instruction with the `data16' instruction prefix), since the 80386 +insists upon masking `%eip' to 16 bits after the word displacement is +added. (See also *note i386-Arch::) + + Note that the `jcxz', `jecxz', `loop', `loopz', `loope', `loopnz' +and `loopne' instructions only come in byte displacements, so that if +you use these instructions (`gcc' does not use them) you may get an +error message (and incorrect code). The AT&T 80386 assembler tries to +get around this problem by expanding `jcxz foo' to + + jcxz cx_zero + jmp cx_nonzero + cx_zero: jmp foo + cx_nonzero: + + +File: as.info, Node: i386-Float, Next: i386-SIMD, Prev: i386-Jumps, Up: i386-Dependent + +9.13.10 Floating Point +---------------------- + +All 80387 floating point types except packed BCD are supported. (BCD +support may be added without much difficulty). These data types are +16-, 32-, and 64- bit integers, and single (32-bit), double (64-bit), +and extended (80-bit) precision floating point. Each supported type +has an instruction mnemonic suffix and a constructor associated with +it. Instruction mnemonic suffixes specify the operand's data type. +Constructors build these data types into memory. + + * Floating point constructors are `.float' or `.single', `.double', + and `.tfloat' for 32-, 64-, and 80-bit formats. These correspond + to instruction mnemonic suffixes `s', `l', and `t'. `t' stands for + 80-bit (ten byte) real. The 80387 only supports this format via + the `fldt' (load 80-bit real to stack top) and `fstpt' (store + 80-bit real and pop stack) instructions. + + * Integer constructors are `.word', `.long' or `.int', and `.quad' + for the 16-, 32-, and 64-bit integer formats. The corresponding + instruction mnemonic suffixes are `s' (single), `l' (long), and + `q' (quad). As with the 80-bit real format, the 64-bit `q' format + is only present in the `fildq' (load quad integer to stack top) + and `fistpq' (store quad integer and pop stack) instructions. + + Register to register operations should not use instruction mnemonic +suffixes. `fstl %st, %st(1)' will give a warning, and be assembled as +if you wrote `fst %st, %st(1)', since all register to register +operations use 80-bit floating point operands. (Contrast this with +`fstl %st, mem', which converts `%st' from 80-bit to 64-bit floating +point format, then stores the result in the 4 byte location `mem') + + +File: as.info, Node: i386-SIMD, Next: i386-16bit, Prev: i386-Float, Up: i386-Dependent + +9.13.11 Intel's MMX and AMD's 3DNow! SIMD Operations +---------------------------------------------------- + +`as' supports Intel's MMX instruction set (SIMD instructions for +integer data), available on Intel's Pentium MMX processors and Pentium +II processors, AMD's K6 and K6-2 processors, Cyrix' M2 processor, and +probably others. It also supports AMD's 3DNow! instruction set (SIMD +instructions for 32-bit floating point data) available on AMD's K6-2 +processor and possibly others in the future. + + Currently, `as' does not support Intel's floating point SIMD, Katmai +(KNI). + + The eight 64-bit MMX operands, also used by 3DNow!, are called +`%mm0', `%mm1', ... `%mm7'. They contain eight 8-bit integers, four +16-bit integers, two 32-bit integers, one 64-bit integer, or two 32-bit +floating point values. The MMX registers cannot be used at the same +time as the floating point stack. + + See Intel and AMD documentation, keeping in mind that the operand +order in instructions is reversed from the Intel syntax. + + +File: as.info, Node: i386-16bit, Next: i386-Arch, Prev: i386-SIMD, Up: i386-Dependent + +9.13.12 Writing 16-bit Code +--------------------------- + +While `as' normally writes only "pure" 32-bit i386 code or 64-bit +x86-64 code depending on the default configuration, it also supports +writing code to run in real mode or in 16-bit protected mode code +segments. To do this, put a `.code16' or `.code16gcc' directive before +the assembly language instructions to be run in 16-bit mode. You can +switch `as' back to writing normal 32-bit code with the `.code32' +directive. + + `.code16gcc' provides experimental support for generating 16-bit +code from gcc, and differs from `.code16' in that `call', `ret', +`enter', `leave', `push', `pop', `pusha', `popa', `pushf', and `popf' +instructions default to 32-bit size. This is so that the stack pointer +is manipulated in the same way over function calls, allowing access to +function parameters at the same stack offsets as in 32-bit mode. +`.code16gcc' also automatically adds address size prefixes where +necessary to use the 32-bit addressing modes that gcc generates. + + The code which `as' generates in 16-bit mode will not necessarily +run on a 16-bit pre-80386 processor. To write code that runs on such a +processor, you must refrain from using _any_ 32-bit constructs which +require `as' to output address or operand size prefixes. + + Note that writing 16-bit code instructions by explicitly specifying a +prefix or an instruction mnemonic suffix within a 32-bit code section +generates different machine instructions than those generated for a +16-bit code segment. In a 32-bit code section, the following code +generates the machine opcode bytes `66 6a 04', which pushes the value +`4' onto the stack, decrementing `%esp' by 2. + + pushw $4 + + The same code in a 16-bit code section would generate the machine +opcode bytes `6a 04' (i.e., without the operand size prefix), which is +correct since the processor default operand size is assumed to be 16 +bits in a 16-bit code section. + + +File: as.info, Node: i386-Bugs, Next: i386-Notes, Prev: i386-Arch, Up: i386-Dependent + +9.13.13 AT&T Syntax bugs +------------------------ + +The UnixWare assembler, and probably other AT&T derived ix86 Unix +assemblers, generate floating point instructions with reversed source +and destination registers in certain cases. Unfortunately, gcc and +possibly many other programs use this reversed syntax, so we're stuck +with it. + + For example + + fsub %st,%st(3) + results in `%st(3)' being updated to `%st - %st(3)' rather than the +expected `%st(3) - %st'. This happens with all the non-commutative +arithmetic floating point operations with two register operands where +the source register is `%st' and the destination register is `%st(i)'. + + +File: as.info, Node: i386-Arch, Next: i386-Bugs, Prev: i386-16bit, Up: i386-Dependent + +9.13.14 Specifying CPU Architecture +----------------------------------- + +`as' may be told to assemble for a particular CPU (sub-)architecture +with the `.arch CPU_TYPE' directive. This directive enables a warning +when gas detects an instruction that is not supported on the CPU +specified. The choices for CPU_TYPE are: + +`i8086' `i186' `i286' `i386' +`i486' `i586' `i686' `pentium' +`pentiumpro' `pentiumii' `pentiumiii' `pentium4' +`prescott' `nocona' `core' `core2' +`corei7' `l1om' +`k6' `k6_2' `athlon' `k8' +`amdfam10' +`generic32' `generic64' +`.mmx' `.sse' `.sse2' `.sse3' +`.ssse3' `.sse4.1' `.sse4.2' `.sse4' +`.avx' `.vmx' `.smx' `.xsave' +`.aes' `.pclmul' `.fma' `.movbe' +`.ept' `.clflush' +`.3dnow' `.3dnowa' `.sse4a' `.sse5' +`.syscall' `.rdtscp' `.svme' `.abm' +`.padlock' + + Apart from the warning, there are only two other effects on `as' +operation; Firstly, if you specify a CPU other than `i486', then shift +by one instructions such as `sarl $1, %eax' will automatically use a +two byte opcode sequence. The larger three byte opcode sequence is +used on the 486 (and when no architecture is specified) because it +executes faster on the 486. Note that you can explicitly request the +two byte opcode by writing `sarl %eax'. Secondly, if you specify +`i8086', `i186', or `i286', _and_ `.code16' or `.code16gcc' then byte +offset conditional jumps will be promoted when necessary to a two +instruction sequence consisting of a conditional jump of the opposite +sense around an unconditional jump to the target. + + Following the CPU architecture (but not a sub-architecture, which +are those starting with a dot), you may specify `jumps' or `nojumps' to +control automatic promotion of conditional jumps. `jumps' is the +default, and enables jump promotion; All external jumps will be of the +long variety, and file-local jumps will be promoted as necessary. +(*note i386-Jumps::) `nojumps' leaves external conditional jumps as +byte offset jumps, and warns about file-local conditional jumps that +`as' promotes. Unconditional jumps are treated as for `jumps'. + + For example + + .arch i8086,nojumps + + +File: as.info, Node: i386-Notes, Prev: i386-Bugs, Up: i386-Dependent + +9.13.15 Notes +------------- + +There is some trickery concerning the `mul' and `imul' instructions +that deserves mention. The 16-, 32-, 64- and 128-bit expanding +multiplies (base opcode `0xf6'; extension 4 for `mul' and 5 for `imul') +can be output only in the one operand form. Thus, `imul %ebx, %eax' +does _not_ select the expanding multiply; the expanding multiply would +clobber the `%edx' register, and this would confuse `gcc' output. Use +`imul %ebx' to get the 64-bit product in `%edx:%eax'. + + We have added a two operand form of `imul' when the first operand is +an immediate mode expression and the second operand is a register. +This is just a shorthand, so that, multiplying `%eax' by 69, for +example, can be done with `imul $69, %eax' rather than `imul $69, %eax, +%eax'. + + +File: as.info, Node: i860-Dependent, Next: i960-Dependent, Prev: i386-Dependent, Up: Machine Dependencies + +9.14 Intel i860 Dependent Features +================================== + +* Menu: + +* Notes-i860:: i860 Notes +* Options-i860:: i860 Command-line Options +* Directives-i860:: i860 Machine Directives +* Opcodes for i860:: i860 Opcodes + + +File: as.info, Node: Notes-i860, Next: Options-i860, Up: i860-Dependent + +9.14.1 i860 Notes +----------------- + +This is a fairly complete i860 assembler which is compatible with the +UNIX System V/860 Release 4 assembler. However, it does not currently +support SVR4 PIC (i.e., `@GOT, @GOTOFF, @PLT'). + + Like the SVR4/860 assembler, the output object format is ELF32. +Currently, this is the only supported object format. If there is +sufficient interest, other formats such as COFF may be implemented. + + Both the Intel and AT&T/SVR4 syntaxes are supported, with the latter +being the default. One difference is that AT&T syntax requires the '%' +prefix on register names while Intel syntax does not. Another +difference is in the specification of relocatable expressions. The +Intel syntax is `ha%expression' whereas the SVR4 syntax is +`[expression]@ha' (and similarly for the "l" and "h" selectors). + + +File: as.info, Node: Options-i860, Next: Directives-i860, Prev: Notes-i860, Up: i860-Dependent + +9.14.2 i860 Command-line Options +-------------------------------- + +9.14.2.1 SVR4 compatibility options +................................... + +`-V' + Print assembler version. + +`-Qy' + Ignored. + +`-Qn' + Ignored. + +9.14.2.2 Other options +...................... + +`-EL' + Select little endian output (this is the default). + +`-EB' + Select big endian output. Note that the i860 always reads + instructions as little endian data, so this option only effects + data and not instructions. + +`-mwarn-expand' + Emit a warning message if any pseudo-instruction expansions + occurred. For example, a `or' instruction with an immediate + larger than 16-bits will be expanded into two instructions. This + is a very undesirable feature to rely on, so this flag can help + detect any code where it happens. One use of it, for instance, has + been to find and eliminate any place where `gcc' may emit these + pseudo-instructions. + +`-mxp' + Enable support for the i860XP instructions and control registers. + By default, this option is disabled so that only the base + instruction set (i.e., i860XR) is supported. + +`-mintel-syntax' + The i860 assembler defaults to AT&T/SVR4 syntax. This option + enables the Intel syntax. + + +File: as.info, Node: Directives-i860, Next: Opcodes for i860, Prev: Options-i860, Up: i860-Dependent + +9.14.3 i860 Machine Directives +------------------------------ + +`.dual' + Enter dual instruction mode. While this directive is supported, the + preferred way to use dual instruction mode is to explicitly code + the dual bit with the `d.' prefix. + +`.enddual' + Exit dual instruction mode. While this directive is supported, the + preferred way to use dual instruction mode is to explicitly code + the dual bit with the `d.' prefix. + +`.atmp' + Change the temporary register used when expanding pseudo + operations. The default register is `r31'. + + The `.dual', `.enddual', and `.atmp' directives are available only +in the Intel syntax mode. + + Both syntaxes allow for the standard `.align' directive. However, +the Intel syntax additionally allows keywords for the alignment +parameter: "`.align type'", where `type' is one of `.short', `.long', +`.quad', `.single', `.double' representing alignments of 2, 4, 16, 4, +and 8, respectively. + + +File: as.info, Node: Opcodes for i860, Prev: Directives-i860, Up: i860-Dependent + +9.14.4 i860 Opcodes +------------------- + +All of the Intel i860XR and i860XP machine instructions are supported. +Please see either _i860 Microprocessor Programmer's Reference Manual_ +or _i860 Microprocessor Architecture_ for more information. + +9.14.4.1 Other instruction support (pseudo-instructions) +........................................................ + +For compatibility with some other i860 assemblers, a number of +pseudo-instructions are supported. While these are supported, they are +a very undesirable feature that should be avoided - in particular, when +they result in an expansion to multiple actual i860 instructions. Below +are the pseudo-instructions that result in expansions. + * Load large immediate into general register: + + The pseudo-instruction `mov imm,%rn' (where the immediate does not + fit within a signed 16-bit field) will be expanded into: + orh large_imm@h,%r0,%rn + or large_imm@l,%rn,%rn + + * Load/store with relocatable address expression: + + For example, the pseudo-instruction `ld.b addr_exp(%rx),%rn' will + be expanded into: + orh addr_exp@ha,%rx,%r31 + ld.l addr_exp@l(%r31),%rn + + The analogous expansions apply to `ld.x, st.x, fld.x, pfld.x, + fst.x', and `pst.x' as well. + + * Signed large immediate with add/subtract: + + If any of the arithmetic operations `adds, addu, subs, subu' are + used with an immediate larger than 16-bits (signed), then they + will be expanded. For instance, the pseudo-instruction `adds + large_imm,%rx,%rn' expands to: + orh large_imm@h,%r0,%r31 + or large_imm@l,%r31,%r31 + adds %r31,%rx,%rn + + * Unsigned large immediate with logical operations: + + Logical operations (`or, andnot, or, xor') also result in + expansions. The pseudo-instruction `or large_imm,%rx,%rn' results + in: + orh large_imm@h,%rx,%r31 + or large_imm@l,%r31,%rn + + Similarly for the others, except for `and' which expands to: + andnot (-1 - large_imm)@h,%rx,%r31 + andnot (-1 - large_imm)@l,%r31,%rn + + +File: as.info, Node: i960-Dependent, Next: IA-64-Dependent, Prev: i860-Dependent, Up: Machine Dependencies + +9.15 Intel 80960 Dependent Features +=================================== + +* Menu: + +* Options-i960:: i960 Command-line Options +* Floating Point-i960:: Floating Point +* Directives-i960:: i960 Machine Directives +* Opcodes for i960:: i960 Opcodes + + +File: as.info, Node: Options-i960, Next: Floating Point-i960, Up: i960-Dependent + +9.15.1 i960 Command-line Options +-------------------------------- + +`-ACA | -ACA_A | -ACB | -ACC | -AKA | -AKB | -AKC | -AMC' + Select the 80960 architecture. Instructions or features not + supported by the selected architecture cause fatal errors. + + `-ACA' is equivalent to `-ACA_A'; `-AKC' is equivalent to `-AMC'. + Synonyms are provided for compatibility with other tools. + + If you do not specify any of these options, `as' generates code + for any instruction or feature that is supported by _some_ version + of the 960 (even if this means mixing architectures!). In + principle, `as' attempts to deduce the minimal sufficient + processor type if none is specified; depending on the object code + format, the processor type may be recorded in the object file. If + it is critical that the `as' output match a specific architecture, + specify that architecture explicitly. + +`-b' + Add code to collect information about conditional branches taken, + for later optimization using branch prediction bits. (The + conditional branch instructions have branch prediction bits in the + CA, CB, and CC architectures.) If BR represents a conditional + branch instruction, the following represents the code generated by + the assembler when `-b' is specified: + + call INCREMENT ROUTINE + .word 0 # pre-counter + Label: BR + call INCREMENT ROUTINE + .word 0 # post-counter + + The counter following a branch records the number of times that + branch was _not_ taken; the difference between the two counters is + the number of times the branch _was_ taken. + + A table of every such `Label' is also generated, so that the + external postprocessor `gbr960' (supplied by Intel) can locate all + the counters. This table is always labeled `__BRANCH_TABLE__'; + this is a local symbol to permit collecting statistics for many + separate object files. The table is word aligned, and begins with + a two-word header. The first word, initialized to 0, is used in + maintaining linked lists of branch tables. The second word is a + count of the number of entries in the table, which follow + immediately: each is a word, pointing to one of the labels + illustrated above. + + +------------+------------+------------+ ... +------------+ + | | | | | | + | *NEXT | COUNT: N | *BRLAB 1 | | *BRLAB N | + | | | | | | + +------------+------------+------------+ ... +------------+ + + __BRANCH_TABLE__ layout + + The first word of the header is used to locate multiple branch + tables, since each object file may contain one. Normally the links + are maintained with a call to an initialization routine, placed at + the beginning of each function in the file. The GNU C compiler + generates these calls automatically when you give it a `-b' option. + For further details, see the documentation of `gbr960'. + +`-no-relax' + Normally, Compare-and-Branch instructions with targets that require + displacements greater than 13 bits (or that have external targets) + are replaced with the corresponding compare (or `chkbit') and + branch instructions. You can use the `-no-relax' option to + specify that `as' should generate errors instead, if the target + displacement is larger than 13 bits. + + This option does not affect the Compare-and-Jump instructions; the + code emitted for them is _always_ adjusted when necessary + (depending on displacement size), regardless of whether you use + `-no-relax'. + + +File: as.info, Node: Floating Point-i960, Next: Directives-i960, Prev: Options-i960, Up: i960-Dependent + +9.15.2 Floating Point +--------------------- + +`as' generates IEEE floating-point numbers for the directives `.float', +`.double', `.extended', and `.single'. + + +File: as.info, Node: Directives-i960, Next: Opcodes for i960, Prev: Floating Point-i960, Up: i960-Dependent + +9.15.3 i960 Machine Directives +------------------------------ + +`.bss SYMBOL, LENGTH, ALIGN' + Reserve LENGTH bytes in the bss section for a local SYMBOL, + aligned to the power of two specified by ALIGN. LENGTH and ALIGN + must be positive absolute expressions. This directive differs + from `.lcomm' only in that it permits you to specify an alignment. + *Note `.lcomm': Lcomm. + +`.extended FLONUMS' + `.extended' expects zero or more flonums, separated by commas; for + each flonum, `.extended' emits an IEEE extended-format (80-bit) + floating-point number. + +`.leafproc CALL-LAB, BAL-LAB' + You can use the `.leafproc' directive in conjunction with the + optimized `callj' instruction to enable faster calls of leaf + procedures. If a procedure is known to call no other procedures, + you may define an entry point that skips procedure prolog code + (and that does not depend on system-supplied saved context), and + declare it as the BAL-LAB using `.leafproc'. If the procedure + also has an entry point that goes through the normal prolog, you + can specify that entry point as CALL-LAB. + + A `.leafproc' declaration is meant for use in conjunction with the + optimized call instruction `callj'; the directive records the data + needed later to choose between converting the `callj' into a `bal' + or a `call'. + + CALL-LAB is optional; if only one argument is present, or if the + two arguments are identical, the single argument is assumed to be + the `bal' entry point. + +`.sysproc NAME, INDEX' + The `.sysproc' directive defines a name for a system procedure. + After you define it using `.sysproc', you can use NAME to refer to + the system procedure identified by INDEX when calling procedures + with the optimized call instruction `callj'. + + Both arguments are required; INDEX must be between 0 and 31 + (inclusive). + + +File: as.info, Node: Opcodes for i960, Prev: Directives-i960, Up: i960-Dependent + +9.15.4 i960 Opcodes +------------------- + +All Intel 960 machine instructions are supported; *note i960 +Command-line Options: Options-i960. for a discussion of selecting the +instruction subset for a particular 960 architecture. + + Some opcodes are processed beyond simply emitting a single +corresponding instruction: `callj', and Compare-and-Branch or +Compare-and-Jump instructions with target displacements larger than 13 +bits. + +* Menu: + +* callj-i960:: `callj' +* Compare-and-branch-i960:: Compare-and-Branch + + +File: as.info, Node: callj-i960, Next: Compare-and-branch-i960, Up: Opcodes for i960 + +9.15.4.1 `callj' +................ + +You can write `callj' to have the assembler or the linker determine the +most appropriate form of subroutine call: `call', `bal', or `calls'. +If the assembly source contains enough information--a `.leafproc' or +`.sysproc' directive defining the operand--then `as' translates the +`callj'; if not, it simply emits the `callj', leaving it for the linker +to resolve. + + +File: as.info, Node: Compare-and-branch-i960, Prev: callj-i960, Up: Opcodes for i960 + +9.15.4.2 Compare-and-Branch +........................... + +The 960 architectures provide combined Compare-and-Branch instructions +that permit you to store the branch target in the lower 13 bits of the +instruction word itself. However, if you specify a branch target far +enough away that its address won't fit in 13 bits, the assembler can +either issue an error, or convert your Compare-and-Branch instruction +into separate instructions to do the compare and the branch. + + Whether `as' gives an error or expands the instruction depends on +two choices you can make: whether you use the `-no-relax' option, and +whether you use a "Compare and Branch" instruction or a "Compare and +Jump" instruction. The "Jump" instructions are _always_ expanded if +necessary; the "Branch" instructions are expanded when necessary +_unless_ you specify `-no-relax'--in which case `as' gives an error +instead. + + These are the Compare-and-Branch instructions, their "Jump" variants, +and the instruction pairs they may expand into: + + Compare and + Branch Jump Expanded to + ------ ------ ------------ + bbc chkbit; bno + bbs chkbit; bo + cmpibe cmpije cmpi; be + cmpibg cmpijg cmpi; bg + cmpibge cmpijge cmpi; bge + cmpibl cmpijl cmpi; bl + cmpible cmpijle cmpi; ble + cmpibno cmpijno cmpi; bno + cmpibne cmpijne cmpi; bne + cmpibo cmpijo cmpi; bo + cmpobe cmpoje cmpo; be + cmpobg cmpojg cmpo; bg + cmpobge cmpojge cmpo; bge + cmpobl cmpojl cmpo; bl + cmpoble cmpojle cmpo; ble + cmpobne cmpojne cmpo; bne + + +File: as.info, Node: IA-64-Dependent, Next: IP2K-Dependent, Prev: i960-Dependent, Up: Machine Dependencies + +9.16 IA-64 Dependent Features +============================= + +* Menu: + +* IA-64 Options:: Options +* IA-64 Syntax:: Syntax +* IA-64 Opcodes:: Opcodes + + +File: as.info, Node: IA-64 Options, Next: IA-64 Syntax, Up: IA-64-Dependent + +9.16.1 Options +-------------- + +`-mconstant-gp' + This option instructs the assembler to mark the resulting object + file as using the "constant GP" model. With this model, it is + assumed that the entire program uses a single global pointer (GP) + value. Note that this option does not in any fashion affect the + machine code emitted by the assembler. All it does is turn on the + EF_IA_64_CONS_GP flag in the ELF file header. + +`-mauto-pic' + This option instructs the assembler to mark the resulting object + file as using the "constant GP without function descriptor" data + model. This model is like the "constant GP" model, except that it + additionally does away with function descriptors. What this means + is that the address of a function refers directly to the + function's code entry-point. Normally, such an address would + refer to a function descriptor, which contains both the code + entry-point and the GP-value needed by the function. Note that + this option does not in any fashion affect the machine code + emitted by the assembler. All it does is turn on the + EF_IA_64_NOFUNCDESC_CONS_GP flag in the ELF file header. + +`-milp32' + +`-milp64' + +`-mlp64' + +`-mp64' + These options select the data model. The assembler defaults to + `-mlp64' (LP64 data model). + +`-mle' + +`-mbe' + These options select the byte order. The `-mle' option selects + little-endian byte order (default) and `-mbe' selects big-endian + byte order. Note that IA-64 machine code always uses + little-endian byte order. + +`-mtune=itanium1' + +`-mtune=itanium2' + Tune for a particular IA-64 CPU, ITANIUM1 or ITANIUM2. The default + is ITANIUM2. + +`-munwind-check=warning' + +`-munwind-check=error' + These options control what the assembler will do when performing + consistency checks on unwind directives. `-munwind-check=warning' + will make the assembler issue a warning when an unwind directive + check fails. This is the default. `-munwind-check=error' will + make the assembler issue an error when an unwind directive check + fails. + +`-mhint.b=ok' + +`-mhint.b=warning' + +`-mhint.b=error' + These options control what the assembler will do when the `hint.b' + instruction is used. `-mhint.b=ok' will make the assembler accept + `hint.b'. `-mint.b=warning' will make the assembler issue a + warning when `hint.b' is used. `-mhint.b=error' will make the + assembler treat `hint.b' as an error, which is the default. + +`-x' + +`-xexplicit' + These options turn on dependency violation checking. + +`-xauto' + This option instructs the assembler to automatically insert stop + bits where necessary to remove dependency violations. This is the + default mode. + +`-xnone' + This option turns off dependency violation checking. + +`-xdebug' + This turns on debug output intended to help tracking down bugs in + the dependency violation checker. + +`-xdebugn' + This is a shortcut for -xnone -xdebug. + +`-xdebugx' + This is a shortcut for -xexplicit -xdebug. + + + +File: as.info, Node: IA-64 Syntax, Next: IA-64 Opcodes, Prev: IA-64 Options, Up: IA-64-Dependent + +9.16.2 Syntax +------------- + +The assembler syntax closely follows the IA-64 Assembly Language +Reference Guide. + +* Menu: + +* IA-64-Chars:: Special Characters +* IA-64-Regs:: Register Names +* IA-64-Bits:: Bit Names + + +File: as.info, Node: IA-64-Chars, Next: IA-64-Regs, Up: IA-64 Syntax + +9.16.2.1 Special Characters +........................... + +`//' is the line comment token. + + `;' can be used instead of a newline to separate statements. + + +File: as.info, Node: IA-64-Regs, Next: IA-64-Bits, Prev: IA-64-Chars, Up: IA-64 Syntax + +9.16.2.2 Register Names +....................... + +The 128 integer registers are referred to as `rN'. The 128 +floating-point registers are referred to as `fN'. The 128 application +registers are referred to as `arN'. The 128 control registers are +referred to as `crN'. The 64 one-bit predicate registers are referred +to as `pN'. The 8 branch registers are referred to as `bN'. In +addition, the assembler defines a number of aliases: `gp' (`r1'), `sp' +(`r12'), `rp' (`b0'), `ret0' (`r8'), `ret1' (`r9'), `ret2' (`r10'), +`ret3' (`r9'), `fargN' (`f8+N'), and `fretN' (`f8+N'). + + For convenience, the assembler also defines aliases for all named +application and control registers. For example, `ar.bsp' refers to the +register backing store pointer (`ar17'). Similarly, `cr.eoi' refers to +the end-of-interrupt register (`cr67'). + + +File: as.info, Node: IA-64-Bits, Prev: IA-64-Regs, Up: IA-64 Syntax + +9.16.2.3 IA-64 Processor-Status-Register (PSR) Bit Names +........................................................ + +The assembler defines bit masks for each of the bits in the IA-64 +processor status register. For example, `psr.ic' corresponds to a +value of 0x2000. These masks are primarily intended for use with the +`ssm'/`sum' and `rsm'/`rum' instructions, but they can be used anywhere +else where an integer constant is expected. + + +File: as.info, Node: IA-64 Opcodes, Prev: IA-64 Syntax, Up: IA-64-Dependent + +9.16.3 Opcodes +-------------- + +For detailed information on the IA-64 machine instruction set, see the +IA-64 Architecture Handbook +(http://developer.intel.com/design/itanium/arch_spec.htm). + + +File: as.info, Node: IP2K-Dependent, Next: LM32-Dependent, Prev: IA-64-Dependent, Up: Machine Dependencies + +9.17 IP2K Dependent Features +============================ + +* Menu: + +* IP2K-Opts:: IP2K Options + + +File: as.info, Node: IP2K-Opts, Up: IP2K-Dependent + +9.17.1 IP2K Options +------------------- + +The Ubicom IP2K version of `as' has a few machine dependent options: + +`-mip2022ext' + `as' can assemble the extended IP2022 instructions, but it will + only do so if this is specifically allowed via this command line + option. + +`-mip2022' + This option restores the assembler's default behaviour of not + permitting the extended IP2022 instructions to be assembled. + + + +File: as.info, Node: LM32-Dependent, Next: M32C-Dependent, Prev: IP2K-Dependent, Up: Machine Dependencies + +9.18 LM32 Dependent Features +============================ + +* Menu: + +* LM32 Options:: Options +* LM32 Syntax:: Syntax +* LM32 Opcodes:: Opcodes + + +File: as.info, Node: LM32 Options, Next: LM32 Syntax, Up: LM32-Dependent + +9.18.1 Options +-------------- + +`-mmultiply-enabled' + Enable multiply instructions. + +`-mdivide-enabled' + Enable divide instructions. + +`-mbarrel-shift-enabled' + Enable barrel-shift instructions. + +`-msign-extend-enabled' + Enable sign extend instructions. + +`-muser-enabled' + Enable user defined instructions. + +`-micache-enabled' + Enable instruction cache related CSRs. + +`-mdcache-enabled' + Enable data cache related CSRs. + +`-mbreak-enabled' + Enable break instructions. + +`-mall-enabled' + Enable all instructions and CSRs. + + + +File: as.info, Node: LM32 Syntax, Next: LM32 Opcodes, Prev: LM32 Options, Up: LM32-Dependent + +9.18.2 Syntax +------------- + +* Menu: + +* LM32-Regs:: Register Names +* LM32-Modifiers:: Relocatable Expression Modifiers + + +File: as.info, Node: LM32-Regs, Next: LM32-Modifiers, Up: LM32 Syntax + +9.18.2.1 Register Names +....................... + +LM32 has 32 x 32-bit general purpose registers `r0', `r1', ... `r31'. + + The following aliases are defined: `gp' - `r26', `fp' - `r27', `sp' +- `r28', `ra' - `r29', `ea' - `r30', `ba' - `r31'. + + LM32 has the following Control and Status Registers (CSRs). + +`IE' + Interrupt enable. + +`IM' + Interrupt mask. + +`IP' + Interrupt pending. + +`ICC' + Instruction cache control. + +`DCC' + Data cache control. + +`CC' + Cycle counter. + +`CFG' + Configuration. + +`EBA' + Exception base address. + +`DC' + Debug control. + +`DEBA' + Debug exception base address. + +`JTX' + JTAG transmit. + +`JRX' + JTAG receive. + +`BP0' + Breakpoint 0. + +`BP1' + Breakpoint 1. + +`BP2' + Breakpoint 2. + +`BP3' + Breakpoint 3. + +`WP0' + Watchpoint 0. + +`WP1' + Watchpoint 1. + +`WP2' + Watchpoint 2. + +`WP3' + Watchpoint 3. + + +File: as.info, Node: LM32-Modifiers, Prev: LM32-Regs, Up: LM32 Syntax + +9.18.2.2 Relocatable Expression Modifiers +......................................... + +The assembler supports several modifiers when using relocatable +addresses in LM32 instruction operands. The general syntax is the +following: + + modifier(relocatable-expression) + +`lo' + This modifier allows you to use bits 0 through 15 of an address + expression as 16 bit relocatable expression. + +`hi' + This modifier allows you to use bits 16 through 23 of an address + expression as 16 bit relocatable expression. + + For example + + ori r4, r4, lo(sym+10) + orhi r4, r4, hi(sym+10) + +`gp' + This modified creates a 16-bit relocatable expression that is the + offset of the symbol from the global pointer. + + mva r4, gp(sym) + +`got' + This modifier places a symbol in the GOT and creates a 16-bit + relocatable expression that is the offset into the GOT of this + symbol. + + lw r4, (gp+got(sym)) + +`gotofflo16' + This modifier allows you to use the bits 0 through 15 of an + address which is an offset from the GOT. + +`gotoffhi16' + This modifier allows you to use the bits 16 through 31 of an + address which is an offset from the GOT. + + orhi r4, r4, gotoffhi16(lsym) + addi r4, r4, gotofflo16(lsym) + + + +File: as.info, Node: LM32 Opcodes, Prev: LM32 Syntax, Up: LM32-Dependent + +9.18.3 Opcodes +-------------- + +For detailed information on the LM32 machine instruction set, see +`http://www.latticesemi.com/products/intellectualproperty/ipcores/mico32/'. + + `as' implements all the standard LM32 opcodes. + + +File: as.info, Node: M32C-Dependent, Next: M32R-Dependent, Prev: LM32-Dependent, Up: Machine Dependencies + +9.19 M32C Dependent Features +============================ + + `as' can assemble code for several different members of the Renesas +M32C family. Normally the default is to assemble code for the M16C +microprocessor. The `-m32c' option may be used to change the default +to the M32C microprocessor. + +* Menu: + +* M32C-Opts:: M32C Options +* M32C-Modifiers:: Symbolic Operand Modifiers + + +File: as.info, Node: M32C-Opts, Next: M32C-Modifiers, Up: M32C-Dependent + +9.19.1 M32C Options +------------------- + +The Renesas M32C version of `as' has these machine-dependent options: + +`-m32c' + Assemble M32C instructions. + +`-m16c' + Assemble M16C instructions (default). + +`-relax' + Enable support for link-time relaxations. + +`-h-tick-hex' + Support H'00 style hex constants in addition to 0x00 style. + + + +File: as.info, Node: M32C-Modifiers, Prev: M32C-Opts, Up: M32C-Dependent + +9.19.2 Symbolic Operand Modifiers +--------------------------------- + +The assembler supports several modifiers when using symbol addresses in +M32C instruction operands. The general syntax is the following: + + %modifier(symbol) + +`%dsp8' +`%dsp16' + These modifiers override the assembler's assumptions about how big + a symbol's address is. Normally, when it sees an operand like + `sym[a0]' it assumes `sym' may require the widest displacement + field (16 bits for `-m16c', 24 bits for `-m32c'). These modifiers + tell it to assume the address will fit in an 8 or 16 bit + (respectively) unsigned displacement. Note that, of course, if it + doesn't actually fit you will get linker errors. Example: + + mov.w %dsp8(sym)[a0],r1 + mov.b #0,%dsp8(sym)[a0] + +`%hi8' + This modifier allows you to load bits 16 through 23 of a 24 bit + address into an 8 bit register. This is useful with, for example, + the M16C `smovf' instruction, which expects a 20 bit address in + `r1h' and `a0'. Example: + + mov.b #%hi8(sym),r1h + mov.w #%lo16(sym),a0 + smovf.b + +`%lo16' + Likewise, this modifier allows you to load bits 0 through 15 of a + 24 bit address into a 16 bit register. + +`%hi16' + This modifier allows you to load bits 16 through 31 of a 32 bit + address into a 16 bit register. While the M32C family only has 24 + bits of address space, it does support addresses in pairs of 16 bit + registers (like `a1a0' for the `lde' instruction). This modifier + is for loading the upper half in such cases. Example: + + mov.w #%hi16(sym),a1 + mov.w #%lo16(sym),a0 + ... + lde.w [a1a0],r1 + + + +File: as.info, Node: M32R-Dependent, Next: M68K-Dependent, Prev: M32C-Dependent, Up: Machine Dependencies + +9.20 M32R Dependent Features +============================ + +* Menu: + +* M32R-Opts:: M32R Options +* M32R-Directives:: M32R Directives +* M32R-Warnings:: M32R Warnings + + +File: as.info, Node: M32R-Opts, Next: M32R-Directives, Up: M32R-Dependent + +9.20.1 M32R Options +------------------- + +The Renease M32R version of `as' has a few machine dependent options: + +`-m32rx' + `as' can assemble code for several different members of the + Renesas M32R family. Normally the default is to assemble code for + the M32R microprocessor. This option may be used to change the + default to the M32RX microprocessor, which adds some more + instructions to the basic M32R instruction set, and some + additional parameters to some of the original instructions. + +`-m32r2' + This option changes the target processor to the the M32R2 + microprocessor. + +`-m32r' + This option can be used to restore the assembler's default + behaviour of assembling for the M32R microprocessor. This can be + useful if the default has been changed by a previous command line + option. + +`-little' + This option tells the assembler to produce little-endian code and + data. The default is dependent upon how the toolchain was + configured. + +`-EL' + This is a synonym for _-little_. + +`-big' + This option tells the assembler to produce big-endian code and + data. + +`-EB' + This is a synonum for _-big_. + +`-KPIC' + This option specifies that the output of the assembler should be + marked as position-independent code (PIC). + +`-parallel' + This option tells the assembler to attempts to combine two + sequential instructions into a single, parallel instruction, where + it is legal to do so. + +`-no-parallel' + This option disables a previously enabled _-parallel_ option. + +`-no-bitinst' + This option disables the support for the extended bit-field + instructions provided by the M32R2. If this support needs to be + re-enabled the _-bitinst_ switch can be used to restore it. + +`-O' + This option tells the assembler to attempt to optimize the + instructions that it produces. This includes filling delay slots + and converting sequential instructions into parallel ones. This + option implies _-parallel_. + +`-warn-explicit-parallel-conflicts' + Instructs `as' to produce warning messages when questionable + parallel instructions are encountered. This option is enabled by + default, but `gcc' disables it when it invokes `as' directly. + Questionable instructions are those whose behaviour would be + different if they were executed sequentially. For example the + code fragment `mv r1, r2 || mv r3, r1' produces a different result + from `mv r1, r2 \n mv r3, r1' since the former moves r1 into r3 + and then r2 into r1, whereas the later moves r2 into r1 and r3. + +`-Wp' + This is a shorter synonym for the + _-warn-explicit-parallel-conflicts_ option. + +`-no-warn-explicit-parallel-conflicts' + Instructs `as' not to produce warning messages when questionable + parallel instructions are encountered. + +`-Wnp' + This is a shorter synonym for the + _-no-warn-explicit-parallel-conflicts_ option. + +`-ignore-parallel-conflicts' + This option tells the assembler's to stop checking parallel + instructions for constraint violations. This ability is provided + for hardware vendors testing chip designs and should not be used + under normal circumstances. + +`-no-ignore-parallel-conflicts' + This option restores the assembler's default behaviour of checking + parallel instructions to detect constraint violations. + +`-Ip' + This is a shorter synonym for the _-ignore-parallel-conflicts_ + option. + +`-nIp' + This is a shorter synonym for the _-no-ignore-parallel-conflicts_ + option. + +`-warn-unmatched-high' + This option tells the assembler to produce a warning message if a + `.high' pseudo op is encountered without a matching `.low' pseudo + op. The presence of such an unmatched pseudo op usually indicates + a programming error. + +`-no-warn-unmatched-high' + Disables a previously enabled _-warn-unmatched-high_ option. + +`-Wuh' + This is a shorter synonym for the _-warn-unmatched-high_ option. + +`-Wnuh' + This is a shorter synonym for the _-no-warn-unmatched-high_ option. + + + +File: as.info, Node: M32R-Directives, Next: M32R-Warnings, Prev: M32R-Opts, Up: M32R-Dependent + +9.20.2 M32R Directives +---------------------- + +The Renease M32R version of `as' has a few architecture specific +directives: + +`low EXPRESSION' + The `low' directive computes the value of its expression and + places the lower 16-bits of the result into the immediate-field of + the instruction. For example: + + or3 r0, r0, #low(0x12345678) ; compute r0 = r0 | 0x5678 + add3, r0, r0, #low(fred) ; compute r0 = r0 + low 16-bits of address of fred + +`high EXPRESSION' + The `high' directive computes the value of its expression and + places the upper 16-bits of the result into the immediate-field of + the instruction. For example: + + seth r0, #high(0x12345678) ; compute r0 = 0x12340000 + seth, r0, #high(fred) ; compute r0 = upper 16-bits of address of fred + +`shigh EXPRESSION' + The `shigh' directive is very similar to the `high' directive. It + also computes the value of its expression and places the upper + 16-bits of the result into the immediate-field of the instruction. + The difference is that `shigh' also checks to see if the lower + 16-bits could be interpreted as a signed number, and if so it + assumes that a borrow will occur from the upper-16 bits. To + compensate for this the `shigh' directive pre-biases the upper 16 + bit value by adding one to it. For example: + + For example: + + seth r0, #shigh(0x12345678) ; compute r0 = 0x12340000 + seth r0, #shigh(0x00008000) ; compute r0 = 0x00010000 + + In the second example the lower 16-bits are 0x8000. If these are + treated as a signed value and sign extended to 32-bits then the + value becomes 0xffff8000. If this value is then added to + 0x00010000 then the result is 0x00008000. + + This behaviour is to allow for the different semantics of the + `or3' and `add3' instructions. The `or3' instruction treats its + 16-bit immediate argument as unsigned whereas the `add3' treats + its 16-bit immediate as a signed value. So for example: + + seth r0, #shigh(0x00008000) + add3 r0, r0, #low(0x00008000) + + Produces the correct result in r0, whereas: + + seth r0, #shigh(0x00008000) + or3 r0, r0, #low(0x00008000) + + Stores 0xffff8000 into r0. + + Note - the `shigh' directive does not know where in the assembly + source code the lower 16-bits of the value are going set, so it + cannot check to make sure that an `or3' instruction is being used + rather than an `add3' instruction. It is up to the programmer to + make sure that correct directives are used. + +`.m32r' + The directive performs a similar thing as the _-m32r_ command line + option. It tells the assembler to only accept M32R instructions + from now on. An instructions from later M32R architectures are + refused. + +`.m32rx' + The directive performs a similar thing as the _-m32rx_ command + line option. It tells the assembler to start accepting the extra + instructions in the M32RX ISA as well as the ordinary M32R ISA. + +`.m32r2' + The directive performs a similar thing as the _-m32r2_ command + line option. It tells the assembler to start accepting the extra + instructions in the M32R2 ISA as well as the ordinary M32R ISA. + +`.little' + The directive performs a similar thing as the _-little_ command + line option. It tells the assembler to start producing + little-endian code and data. This option should be used with care + as producing mixed-endian binary files is fraught with danger. + +`.big' + The directive performs a similar thing as the _-big_ command line + option. It tells the assembler to start producing big-endian code + and data. This option should be used with care as producing + mixed-endian binary files is fraught with danger. + + + +File: as.info, Node: M32R-Warnings, Prev: M32R-Directives, Up: M32R-Dependent + +9.20.3 M32R Warnings +-------------------- + +There are several warning and error messages that can be produced by +`as' which are specific to the M32R: + +`output of 1st instruction is the same as an input to 2nd instruction - is this intentional ?' + This message is only produced if warnings for explicit parallel + conflicts have been enabled. It indicates that the assembler has + encountered a parallel instruction in which the destination + register of the left hand instruction is used as an input register + in the right hand instruction. For example in this code fragment + `mv r1, r2 || neg r3, r1' register r1 is the destination of the + move instruction and the input to the neg instruction. + +`output of 2nd instruction is the same as an input to 1st instruction - is this intentional ?' + This message is only produced if warnings for explicit parallel + conflicts have been enabled. It indicates that the assembler has + encountered a parallel instruction in which the destination + register of the right hand instruction is used as an input + register in the left hand instruction. For example in this code + fragment `mv r1, r2 || neg r2, r3' register r2 is the destination + of the neg instruction and the input to the move instruction. + +`instruction `...' is for the M32RX only' + This message is produced when the assembler encounters an + instruction which is only supported by the M32Rx processor, and + the `-m32rx' command line flag has not been specified to allow + assembly of such instructions. + +`unknown instruction `...'' + This message is produced when the assembler encounters an + instruction which it does not recognize. + +`only the NOP instruction can be issued in parallel on the m32r' + This message is produced when the assembler encounters a parallel + instruction which does not involve a NOP instruction and the + `-m32rx' command line flag has not been specified. Only the M32Rx + processor is able to execute two instructions in parallel. + +`instruction `...' cannot be executed in parallel.' + This message is produced when the assembler encounters a parallel + instruction which is made up of one or two instructions which + cannot be executed in parallel. + +`Instructions share the same execution pipeline' + This message is produced when the assembler encounters a parallel + instruction whoes components both use the same execution pipeline. + +`Instructions write to the same destination register.' + This message is produced when the assembler encounters a parallel + instruction where both components attempt to modify the same + register. For example these code fragments will produce this + message: `mv r1, r2 || neg r1, r3' `jl r0 || mv r14, r1' `st r2, + @-r1 || mv r1, r3' `mv r1, r2 || ld r0, @r1+' `cmp r1, r2 || addx + r3, r4' (Both write to the condition bit) + + + +File: as.info, Node: M68K-Dependent, Next: M68HC11-Dependent, Prev: M32R-Dependent, Up: Machine Dependencies + +9.21 M680x0 Dependent Features +============================== + +* Menu: + +* M68K-Opts:: M680x0 Options +* M68K-Syntax:: Syntax +* M68K-Moto-Syntax:: Motorola Syntax +* M68K-Float:: Floating Point +* M68K-Directives:: 680x0 Machine Directives +* M68K-opcodes:: Opcodes + + +File: as.info, Node: M68K-Opts, Next: M68K-Syntax, Up: M68K-Dependent + +9.21.1 M680x0 Options +--------------------- + +The Motorola 680x0 version of `as' has a few machine dependent options: + +`-march=ARCHITECTURE' + This option specifies a target architecture. The following + architectures are recognized: `68000', `68010', `68020', `68030', + `68040', `68060', `cpu32', `isaa', `isaaplus', `isab', `isac' and + `cfv4e'. + +`-mcpu=CPU' + This option specifies a target cpu. When used in conjunction with + the `-march' option, the cpu must be within the specified + architecture. Also, the generic features of the architecture are + used for instruction generation, rather than those of the specific + chip. + +`-m[no-]68851' + +`-m[no-]68881' + +`-m[no-]div' + +`-m[no-]usp' + +`-m[no-]float' + +`-m[no-]mac' + +`-m[no-]emac' + Enable or disable various architecture specific features. If a + chip or architecture by default supports an option (for instance + `-march=isaaplus' includes the `-mdiv' option), explicitly + disabling the option will override the default. + +`-l' + You can use the `-l' option to shorten the size of references to + undefined symbols. If you do not use the `-l' option, references + to undefined symbols are wide enough for a full `long' (32 bits). + (Since `as' cannot know where these symbols end up, `as' can only + allocate space for the linker to fill in later. Since `as' does + not know how far away these symbols are, it allocates as much + space as it can.) If you use this option, the references are only + one word wide (16 bits). This may be useful if you want the + object file to be as small as possible, and you know that the + relevant symbols are always less than 17 bits away. + +`--register-prefix-optional' + For some configurations, especially those where the compiler + normally does not prepend an underscore to the names of user + variables, the assembler requires a `%' before any use of a + register name. This is intended to let the assembler distinguish + between C variables and functions named `a0' through `a7', and so + on. The `%' is always accepted, but is not required for certain + configurations, notably `sun3'. The `--register-prefix-optional' + option may be used to permit omitting the `%' even for + configurations for which it is normally required. If this is + done, it will generally be impossible to refer to C variables and + functions with the same names as register names. + +`--bitwise-or' + Normally the character `|' is treated as a comment character, which + means that it can not be used in expressions. The `--bitwise-or' + option turns `|' into a normal character. In this mode, you must + either use C style comments, or start comments with a `#' character + at the beginning of a line. + +`--base-size-default-16 --base-size-default-32' + If you use an addressing mode with a base register without + specifying the size, `as' will normally use the full 32 bit value. + For example, the addressing mode `%a0@(%d0)' is equivalent to + `%a0@(%d0:l)'. You may use the `--base-size-default-16' option to + tell `as' to default to using the 16 bit value. In this case, + `%a0@(%d0)' is equivalent to `%a0@(%d0:w)'. You may use the + `--base-size-default-32' option to restore the default behaviour. + +`--disp-size-default-16 --disp-size-default-32' + If you use an addressing mode with a displacement, and the value + of the displacement is not known, `as' will normally assume that + the value is 32 bits. For example, if the symbol `disp' has not + been defined, `as' will assemble the addressing mode + `%a0@(disp,%d0)' as though `disp' is a 32 bit value. You may use + the `--disp-size-default-16' option to tell `as' to instead assume + that the displacement is 16 bits. In this case, `as' will + assemble `%a0@(disp,%d0)' as though `disp' is a 16 bit value. You + may use the `--disp-size-default-32' option to restore the default + behaviour. + +`--pcrel' + Always keep branches PC-relative. In the M680x0 architecture all + branches are defined as PC-relative. However, on some processors + they are limited to word displacements maximum. When `as' needs a + long branch that is not available, it normally emits an absolute + jump instead. This option disables this substitution. When this + option is given and no long branches are available, only word + branches will be emitted. An error message will be generated if a + word branch cannot reach its target. This option has no effect on + 68020 and other processors that have long branches. *note Branch + Improvement: M68K-Branch. + +`-m68000' + `as' can assemble code for several different members of the + Motorola 680x0 family. The default depends upon how `as' was + configured when it was built; normally, the default is to assemble + code for the 68020 microprocessor. The following options may be + used to change the default. These options control which + instructions and addressing modes are permitted. The members of + the 680x0 family are very similar. For detailed information about + the differences, see the Motorola manuals. + + `-m68000' + `-m68ec000' + `-m68hc000' + `-m68hc001' + `-m68008' + `-m68302' + `-m68306' + `-m68307' + `-m68322' + `-m68356' + Assemble for the 68000. `-m68008', `-m68302', and so on are + synonyms for `-m68000', since the chips are the same from the + point of view of the assembler. + + `-m68010' + Assemble for the 68010. + + `-m68020' + `-m68ec020' + Assemble for the 68020. This is normally the default. + + `-m68030' + `-m68ec030' + Assemble for the 68030. + + `-m68040' + `-m68ec040' + Assemble for the 68040. + + `-m68060' + `-m68ec060' + Assemble for the 68060. + + `-mcpu32' + `-m68330' + `-m68331' + `-m68332' + `-m68333' + `-m68334' + `-m68336' + `-m68340' + `-m68341' + `-m68349' + `-m68360' + Assemble for the CPU32 family of chips. + + `-m5200' + + `-m5202' + + `-m5204' + + `-m5206' + + `-m5206e' + + `-m521x' + + `-m5249' + + `-m528x' + + `-m5307' + + `-m5407' + + `-m547x' + + `-m548x' + + `-mcfv4' + + `-mcfv4e' + Assemble for the ColdFire family of chips. + + `-m68881' + `-m68882' + Assemble 68881 floating point instructions. This is the + default for the 68020, 68030, and the CPU32. The 68040 and + 68060 always support floating point instructions. + + `-mno-68881' + Do not assemble 68881 floating point instructions. This is + the default for 68000 and the 68010. The 68040 and 68060 + always support floating point instructions, even if this + option is used. + + `-m68851' + Assemble 68851 MMU instructions. This is the default for the + 68020, 68030, and 68060. The 68040 accepts a somewhat + different set of MMU instructions; `-m68851' and `-m68040' + should not be used together. + + `-mno-68851' + Do not assemble 68851 MMU instructions. This is the default + for the 68000, 68010, and the CPU32. The 68040 accepts a + somewhat different set of MMU instructions. + + +File: as.info, Node: M68K-Syntax, Next: M68K-Moto-Syntax, Prev: M68K-Opts, Up: M68K-Dependent + +9.21.2 Syntax +------------- + +This syntax for the Motorola 680x0 was developed at MIT. + + The 680x0 version of `as' uses instructions names and syntax +compatible with the Sun assembler. Intervening periods are ignored; +for example, `movl' is equivalent to `mov.l'. + + In the following table APC stands for any of the address registers +(`%a0' through `%a7'), the program counter (`%pc'), the zero-address +relative to the program counter (`%zpc'), a suppressed address register +(`%za0' through `%za7'), or it may be omitted entirely. The use of +SIZE means one of `w' or `l', and it may be omitted, along with the +leading colon, unless a scale is also specified. The use of SCALE +means one of `1', `2', `4', or `8', and it may always be omitted along +with the leading colon. + + The following addressing modes are understood: +"Immediate" + `#NUMBER' + +"Data Register" + `%d0' through `%d7' + +"Address Register" + `%a0' through `%a7' + `%a7' is also known as `%sp', i.e., the Stack Pointer. `%a6' is + also known as `%fp', the Frame Pointer. + +"Address Register Indirect" + `%a0@' through `%a7@' + +"Address Register Postincrement" + `%a0@+' through `%a7@+' + +"Address Register Predecrement" + `%a0@-' through `%a7@-' + +"Indirect Plus Offset" + `APC@(NUMBER)' + +"Index" + `APC@(NUMBER,REGISTER:SIZE:SCALE)' + + The NUMBER may be omitted. + +"Postindex" + `APC@(NUMBER)@(ONUMBER,REGISTER:SIZE:SCALE)' + + The ONUMBER or the REGISTER, but not both, may be omitted. + +"Preindex" + `APC@(NUMBER,REGISTER:SIZE:SCALE)@(ONUMBER)' + + The NUMBER may be omitted. Omitting the REGISTER produces the + Postindex addressing mode. + +"Absolute" + `SYMBOL', or `DIGITS', optionally followed by `:b', `:w', or `:l'. + + +File: as.info, Node: M68K-Moto-Syntax, Next: M68K-Float, Prev: M68K-Syntax, Up: M68K-Dependent + +9.21.3 Motorola Syntax +---------------------- + +The standard Motorola syntax for this chip differs from the syntax +already discussed (*note Syntax: M68K-Syntax.). `as' can accept +Motorola syntax for operands, even if MIT syntax is used for other +operands in the same instruction. The two kinds of syntax are fully +compatible. + + In the following table APC stands for any of the address registers +(`%a0' through `%a7'), the program counter (`%pc'), the zero-address +relative to the program counter (`%zpc'), or a suppressed address +register (`%za0' through `%za7'). The use of SIZE means one of `w' or +`l', and it may always be omitted along with the leading dot. The use +of SCALE means one of `1', `2', `4', or `8', and it may always be +omitted along with the leading asterisk. + + The following additional addressing modes are understood: + +"Address Register Indirect" + `(%a0)' through `(%a7)' + `%a7' is also known as `%sp', i.e., the Stack Pointer. `%a6' is + also known as `%fp', the Frame Pointer. + +"Address Register Postincrement" + `(%a0)+' through `(%a7)+' + +"Address Register Predecrement" + `-(%a0)' through `-(%a7)' + +"Indirect Plus Offset" + `NUMBER(%A0)' through `NUMBER(%A7)', or `NUMBER(%PC)'. + + The NUMBER may also appear within the parentheses, as in + `(NUMBER,%A0)'. When used with the PC, the NUMBER may be omitted + (with an address register, omitting the NUMBER produces Address + Register Indirect mode). + +"Index" + `NUMBER(APC,REGISTER.SIZE*SCALE)' + + The NUMBER may be omitted, or it may appear within the + parentheses. The APC may be omitted. The REGISTER and the APC + may appear in either order. If both APC and REGISTER are address + registers, and the SIZE and SCALE are omitted, then the first + register is taken as the base register, and the second as the + index register. + +"Postindex" + `([NUMBER,APC],REGISTER.SIZE*SCALE,ONUMBER)' + + The ONUMBER, or the REGISTER, or both, may be omitted. Either the + NUMBER or the APC may be omitted, but not both. + +"Preindex" + `([NUMBER,APC,REGISTER.SIZE*SCALE],ONUMBER)' + + The NUMBER, or the APC, or the REGISTER, or any two of them, may + be omitted. The ONUMBER may be omitted. The REGISTER and the APC + may appear in either order. If both APC and REGISTER are address + registers, and the SIZE and SCALE are omitted, then the first + register is taken as the base register, and the second as the + index register. + + +File: as.info, Node: M68K-Float, Next: M68K-Directives, Prev: M68K-Moto-Syntax, Up: M68K-Dependent + +9.21.4 Floating Point +--------------------- + +Packed decimal (P) format floating literals are not supported. Feel +free to add the code! + + The floating point formats generated by directives are these. + +`.float' + `Single' precision floating point constants. + +`.double' + `Double' precision floating point constants. + +`.extend' +`.ldouble' + `Extended' precision (`long double') floating point constants. + + +File: as.info, Node: M68K-Directives, Next: M68K-opcodes, Prev: M68K-Float, Up: M68K-Dependent + +9.21.5 680x0 Machine Directives +------------------------------- + +In order to be compatible with the Sun assembler the 680x0 assembler +understands the following directives. + +`.data1' + This directive is identical to a `.data 1' directive. + +`.data2' + This directive is identical to a `.data 2' directive. + +`.even' + This directive is a special case of the `.align' directive; it + aligns the output to an even byte boundary. + +`.skip' + This directive is identical to a `.space' directive. + +`.arch NAME' + Select the target architecture and extension features. Valid + values for NAME are the same as for the `-march' command line + option. This directive cannot be specified after any instructions + have been assembled. If it is given multiple times, or in + conjunction with the `-march' option, all uses must be for the + same architecture and extension set. + +`.cpu NAME' + Select the target cpu. Valid valuse for NAME are the same as for + the `-mcpu' command line option. This directive cannot be + specified after any instructions have been assembled. If it is + given multiple times, or in conjunction with the `-mopt' option, + all uses must be for the same cpu. + + + +File: as.info, Node: M68K-opcodes, Prev: M68K-Directives, Up: M68K-Dependent + +9.21.6 Opcodes +-------------- + +* Menu: + +* M68K-Branch:: Branch Improvement +* M68K-Chars:: Special Characters + + +File: as.info, Node: M68K-Branch, Next: M68K-Chars, Up: M68K-opcodes + +9.21.6.1 Branch Improvement +........................... + +Certain pseudo opcodes are permitted for branch instructions. They +expand to the shortest branch instruction that reach the target. +Generally these mnemonics are made by substituting `j' for `b' at the +start of a Motorola mnemonic. + + The following table summarizes the pseudo-operations. A `*' flags +cases that are more fully described after the table: + + Displacement + +------------------------------------------------------------ + | 68020 68000/10, not PC-relative OK + Pseudo-Op |BYTE WORD LONG ABSOLUTE LONG JUMP ** + +------------------------------------------------------------ + jbsr |bsrs bsrw bsrl jsr + jra |bras braw bral jmp + * jXX |bXXs bXXw bXXl bNXs;jmp + * dbXX | N/A dbXXw dbXX;bras;bral dbXX;bras;jmp + fjXX | N/A fbXXw fbXXl N/A + + XX: condition + NX: negative of condition XX + `*'--see full description below + `**'--this expansion mode is disallowed by `--pcrel' + +`jbsr' +`jra' + These are the simplest jump pseudo-operations; they always map to + one particular machine instruction, depending on the displacement + to the branch target. This instruction will be a byte or word + branch is that is sufficient. Otherwise, a long branch will be + emitted if available. If no long branches are available and the + `--pcrel' option is not given, an absolute long jump will be + emitted instead. If no long branches are available, the `--pcrel' + option is given, and a word branch cannot reach the target, an + error message is generated. + + In addition to standard branch operands, `as' allows these + pseudo-operations to have all operands that are allowed for jsr + and jmp, substituting these instructions if the operand given is + not valid for a branch instruction. + +`jXX' + Here, `jXX' stands for an entire family of pseudo-operations, + where XX is a conditional branch or condition-code test. The full + list of pseudo-ops in this family is: + jhi jls jcc jcs jne jeq jvc + jvs jpl jmi jge jlt jgt jle + + Usually, each of these pseudo-operations expands to a single branch + instruction. However, if a word branch is not sufficient, no long + branches are available, and the `--pcrel' option is not given, `as' + issues a longer code fragment in terms of NX, the opposite + condition to XX. For example, under these conditions: + jXX foo + gives + bNXs oof + jmp foo + oof: + +`dbXX' + The full family of pseudo-operations covered here is + dbhi dbls dbcc dbcs dbne dbeq dbvc + dbvs dbpl dbmi dbge dblt dbgt dble + dbf dbra dbt + + Motorola `dbXX' instructions allow word displacements only. When + a word displacement is sufficient, each of these pseudo-operations + expands to the corresponding Motorola instruction. When a word + displacement is not sufficient and long branches are available, + when the source reads `dbXX foo', `as' emits + dbXX oo1 + bras oo2 + oo1:bral foo + oo2: + + If, however, long branches are not available and the `--pcrel' + option is not given, `as' emits + dbXX oo1 + bras oo2 + oo1:jmp foo + oo2: + +`fjXX' + This family includes + fjne fjeq fjge fjlt fjgt fjle fjf + fjt fjgl fjgle fjnge fjngl fjngle fjngt + fjnle fjnlt fjoge fjogl fjogt fjole fjolt + fjor fjseq fjsf fjsne fjst fjueq fjuge + fjugt fjule fjult fjun + + Each of these pseudo-operations always expands to a single Motorola + coprocessor branch instruction, word or long. All Motorola + coprocessor branch instructions allow both word and long + displacements. + + + +File: as.info, Node: M68K-Chars, Prev: M68K-Branch, Up: M68K-opcodes + +9.21.6.2 Special Characters +........................... + +The immediate character is `#' for Sun compatibility. The line-comment +character is `|' (unless the `--bitwise-or' option is used). If a `#' +appears at the beginning of a line, it is treated as a comment unless +it looks like `# line file', in which case it is treated normally. + + +File: as.info, Node: M68HC11-Dependent, Next: MicroBlaze-Dependent, Prev: M68K-Dependent, Up: Machine Dependencies + +9.22 M68HC11 and M68HC12 Dependent Features +=========================================== + +* Menu: + +* M68HC11-Opts:: M68HC11 and M68HC12 Options +* M68HC11-Syntax:: Syntax +* M68HC11-Modifiers:: Symbolic Operand Modifiers +* M68HC11-Directives:: Assembler Directives +* M68HC11-Float:: Floating Point +* M68HC11-opcodes:: Opcodes + + +File: as.info, Node: M68HC11-Opts, Next: M68HC11-Syntax, Up: M68HC11-Dependent + +9.22.1 M68HC11 and M68HC12 Options +---------------------------------- + +The Motorola 68HC11 and 68HC12 version of `as' have a few machine +dependent options. + +`-m68hc11' + This option switches the assembler in the M68HC11 mode. In this + mode, the assembler only accepts 68HC11 operands and mnemonics. It + produces code for the 68HC11. + +`-m68hc12' + This option switches the assembler in the M68HC12 mode. In this + mode, the assembler also accepts 68HC12 operands and mnemonics. It + produces code for the 68HC12. A few 68HC11 instructions are + replaced by some 68HC12 instructions as recommended by Motorola + specifications. + +`-m68hcs12' + This option switches the assembler in the M68HCS12 mode. This + mode is similar to `-m68hc12' but specifies to assemble for the + 68HCS12 series. The only difference is on the assembling of the + `movb' and `movw' instruction when a PC-relative operand is used. + +`-mshort' + This option controls the ABI and indicates to use a 16-bit integer + ABI. It has no effect on the assembled instructions. This is the + default. + +`-mlong' + This option controls the ABI and indicates to use a 32-bit integer + ABI. + +`-mshort-double' + This option controls the ABI and indicates to use a 32-bit float + ABI. This is the default. + +`-mlong-double' + This option controls the ABI and indicates to use a 64-bit float + ABI. + +`--strict-direct-mode' + You can use the `--strict-direct-mode' option to disable the + automatic translation of direct page mode addressing into extended + mode when the instruction does not support direct mode. For + example, the `clr' instruction does not support direct page mode + addressing. When it is used with the direct page mode, `as' will + ignore it and generate an absolute addressing. This option + prevents `as' from doing this, and the wrong usage of the direct + page mode will raise an error. + +`--short-branches' + The `--short-branches' option turns off the translation of + relative branches into absolute branches when the branch offset is + out of range. By default `as' transforms the relative branch + (`bsr', `bgt', `bge', `beq', `bne', `ble', `blt', `bhi', `bcc', + `bls', `bcs', `bmi', `bvs', `bvs', `bra') into an absolute branch + when the offset is out of the -128 .. 127 range. In that case, + the `bsr' instruction is translated into a `jsr', the `bra' + instruction is translated into a `jmp' and the conditional + branches instructions are inverted and followed by a `jmp'. This + option disables these translations and `as' will generate an error + if a relative branch is out of range. This option does not affect + the optimization associated to the `jbra', `jbsr' and `jbXX' + pseudo opcodes. + +`--force-long-branches' + The `--force-long-branches' option forces the translation of + relative branches into absolute branches. This option does not + affect the optimization associated to the `jbra', `jbsr' and + `jbXX' pseudo opcodes. + +`--print-insn-syntax' + You can use the `--print-insn-syntax' option to obtain the syntax + description of the instruction when an error is detected. + +`--print-opcodes' + The `--print-opcodes' option prints the list of all the + instructions with their syntax. The first item of each line + represents the instruction name and the rest of the line indicates + the possible operands for that instruction. The list is printed in + alphabetical order. Once the list is printed `as' exits. + +`--generate-example' + The `--generate-example' option is similar to `--print-opcodes' + but it generates an example for each instruction instead. + + +File: as.info, Node: M68HC11-Syntax, Next: M68HC11-Modifiers, Prev: M68HC11-Opts, Up: M68HC11-Dependent + +9.22.2 Syntax +------------- + +In the M68HC11 syntax, the instruction name comes first and it may be +followed by one or several operands (up to three). Operands are +separated by comma (`,'). In the normal mode, `as' will complain if too +many operands are specified for a given instruction. In the MRI mode +(turned on with `-M' option), it will treat them as comments. Example: + + inx + lda #23 + bset 2,x #4 + brclr *bot #8 foo + + The following addressing modes are understood for 68HC11 and 68HC12: +"Immediate" + `#NUMBER' + +"Address Register" + `NUMBER,X', `NUMBER,Y' + + The NUMBER may be omitted in which case 0 is assumed. + +"Direct Addressing mode" + `*SYMBOL', or `*DIGITS' + +"Absolute" + `SYMBOL', or `DIGITS' + + The M68HC12 has other more complex addressing modes. All of them are +supported and they are represented below: + +"Constant Offset Indexed Addressing Mode" + `NUMBER,REG' + + The NUMBER may be omitted in which case 0 is assumed. The + register can be either `X', `Y', `SP' or `PC'. The assembler will + use the smaller post-byte definition according to the constant + value (5-bit constant offset, 9-bit constant offset or 16-bit + constant offset). If the constant is not known by the assembler + it will use the 16-bit constant offset post-byte and the value + will be resolved at link time. + +"Offset Indexed Indirect" + `[NUMBER,REG]' + + The register can be either `X', `Y', `SP' or `PC'. + +"Auto Pre-Increment/Pre-Decrement/Post-Increment/Post-Decrement" + `NUMBER,-REG' `NUMBER,+REG' `NUMBER,REG-' `NUMBER,REG+' + + The number must be in the range `-8'..`+8' and must not be 0. The + register can be either `X', `Y', `SP' or `PC'. + +"Accumulator Offset" + `ACC,REG' + + The accumulator register can be either `A', `B' or `D'. The + register can be either `X', `Y', `SP' or `PC'. + +"Accumulator D offset indexed-indirect" + `[D,REG]' + + The register can be either `X', `Y', `SP' or `PC'. + + + For example: + + ldab 1024,sp + ldd [10,x] + orab 3,+x + stab -2,y- + ldx a,pc + sty [d,sp] + + +File: as.info, Node: M68HC11-Modifiers, Next: M68HC11-Directives, Prev: M68HC11-Syntax, Up: M68HC11-Dependent + +9.22.3 Symbolic Operand Modifiers +--------------------------------- + +The assembler supports several modifiers when using symbol addresses in +68HC11 and 68HC12 instruction operands. The general syntax is the +following: + + %modifier(symbol) + +`%addr' + This modifier indicates to the assembler and linker to use the + 16-bit physical address corresponding to the symbol. This is + intended to be used on memory window systems to map a symbol in + the memory bank window. If the symbol is in a memory expansion + part, the physical address corresponds to the symbol address + within the memory bank window. If the symbol is not in a memory + expansion part, this is the symbol address (using or not using the + %addr modifier has no effect in that case). + +`%page' + This modifier indicates to use the memory page number corresponding + to the symbol. If the symbol is in a memory expansion part, its + page number is computed by the linker as a number used to map the + page containing the symbol in the memory bank window. If the + symbol is not in a memory expansion part, the page number is 0. + +`%hi' + This modifier indicates to use the 8-bit high part of the physical + address of the symbol. + +`%lo' + This modifier indicates to use the 8-bit low part of the physical + address of the symbol. + + + For example a 68HC12 call to a function `foo_example' stored in +memory expansion part could be written as follows: + + call %addr(foo_example),%page(foo_example) + + and this is equivalent to + + call foo_example + + And for 68HC11 it could be written as follows: + + ldab #%page(foo_example) + stab _page_switch + jsr %addr(foo_example) + + +File: as.info, Node: M68HC11-Directives, Next: M68HC11-Float, Prev: M68HC11-Modifiers, Up: M68HC11-Dependent + +9.22.4 Assembler Directives +--------------------------- + +The 68HC11 and 68HC12 version of `as' have the following specific +assembler directives: + +`.relax' + The relax directive is used by the `GNU Compiler' to emit a + specific relocation to mark a group of instructions for linker + relaxation. The sequence of instructions within the group must be + known to the linker so that relaxation can be performed. + +`.mode [mshort|mlong|mshort-double|mlong-double]' + This directive specifies the ABI. It overrides the `-mshort', + `-mlong', `-mshort-double' and `-mlong-double' options. + +`.far SYMBOL' + This directive marks the symbol as a `far' symbol meaning that it + uses a `call/rtc' calling convention as opposed to `jsr/rts'. + During a final link, the linker will identify references to the + `far' symbol and will verify the proper calling convention. + +`.interrupt SYMBOL' + This directive marks the symbol as an interrupt entry point. This + information is then used by the debugger to correctly unwind the + frame across interrupts. + +`.xrefb SYMBOL' + This directive is defined for compatibility with the + `Specification for Motorola 8 and 16-Bit Assembly Language Input + Standard' and is ignored. + + + +File: as.info, Node: M68HC11-Float, Next: M68HC11-opcodes, Prev: M68HC11-Directives, Up: M68HC11-Dependent + +9.22.5 Floating Point +--------------------- + +Packed decimal (P) format floating literals are not supported. Feel +free to add the code! + + The floating point formats generated by directives are these. + +`.float' + `Single' precision floating point constants. + +`.double' + `Double' precision floating point constants. + +`.extend' +`.ldouble' + `Extended' precision (`long double') floating point constants. + + +File: as.info, Node: M68HC11-opcodes, Prev: M68HC11-Float, Up: M68HC11-Dependent + +9.22.6 Opcodes +-------------- + +* Menu: + +* M68HC11-Branch:: Branch Improvement + + +File: as.info, Node: M68HC11-Branch, Up: M68HC11-opcodes + +9.22.6.1 Branch Improvement +........................... + +Certain pseudo opcodes are permitted for branch instructions. They +expand to the shortest branch instruction that reach the target. +Generally these mnemonics are made by prepending `j' to the start of +Motorola mnemonic. These pseudo opcodes are not affected by the +`--short-branches' or `--force-long-branches' options. + + The following table summarizes the pseudo-operations. + + Displacement Width + +-------------------------------------------------------------+ + | Options | + | --short-branches --force-long-branches | + +--------------------------+----------------------------------+ + Op |BYTE WORD | BYTE WORD | + +--------------------------+----------------------------------+ + bsr | bsr <pc-rel> <error> | jsr <abs> | + bra | bra <pc-rel> <error> | jmp <abs> | + jbsr | bsr <pc-rel> jsr <abs> | bsr <pc-rel> jsr <abs> | + jbra | bra <pc-rel> jmp <abs> | bra <pc-rel> jmp <abs> | + bXX | bXX <pc-rel> <error> | bNX +3; jmp <abs> | + jbXX | bXX <pc-rel> bNX +3; | bXX <pc-rel> bNX +3; jmp <abs> | + | jmp <abs> | | + +--------------------------+----------------------------------+ + XX: condition + NX: negative of condition XX + +`jbsr' +`jbra' + These are the simplest jump pseudo-operations; they always map to + one particular machine instruction, depending on the displacement + to the branch target. + +`jbXX' + Here, `jbXX' stands for an entire family of pseudo-operations, + where XX is a conditional branch or condition-code test. The full + list of pseudo-ops in this family is: + jbcc jbeq jbge jbgt jbhi jbvs jbpl jblo + jbcs jbne jblt jble jbls jbvc jbmi + + For the cases of non-PC relative displacements and long + displacements, `as' issues a longer code fragment in terms of NX, + the opposite condition to XX. For example, for the non-PC + relative case: + jbXX foo + gives + bNXs oof + jmp foo + oof: + + + +File: as.info, Node: MicroBlaze-Dependent, Next: MIPS-Dependent, Prev: M68HC11-Dependent, Up: Machine Dependencies + +9.23 MicroBlaze Dependent Features +================================== + + The Xilinx MicroBlaze processor family includes several variants, +all using the same core instruction set. This chapter covers features +of the GNU assembler that are specific to the MicroBlaze architecture. +For details about the MicroBlaze instruction set, please see the +`MicroBlaze Processor Reference Guide (UG081)' available at +www.xilinx.com. + +* Menu: + +* MicroBlaze Directives:: Directives for MicroBlaze Processors. + + +File: as.info, Node: MicroBlaze Directives, Up: MicroBlaze-Dependent + +9.23.1 Directives +----------------- + +A number of assembler directives are available for MicroBlaze. + +`.data8 EXPRESSION,...' + This directive is an alias for `.byte'. Each expression is + assembled into an eight-bit value. + +`.data16 EXPRESSION,...' + This directive is an alias for `.hword'. Each expression is + assembled into an 16-bit value. + +`.data32 EXPRESSION,...' + This directive is an alias for `.word'. Each expression is + assembled into an 32-bit value. + +`.ent NAME[,LABEL]' + This directive is an alias for `.func' denoting the start of + function NAME at (optional) LABEL. + +`.end NAME[,LABEL]' + This directive is an alias for `.endfunc' denoting the end of + function NAME. + +`.gpword LABEL,...' + This directive is an alias for `.rva'. The resolved address of + LABEL is stored in the data section. + +`.weakext LABEL' + Declare that LABEL is a weak external symbol. + +`.rodata' + Switch to .rodata section. Equivalent to `.section .rodata' + +`.sdata2' + Switch to .sdata2 section. Equivalent to `.section .sdata2' + +`.sdata' + Switch to .sdata section. Equivalent to `.section .sdata' + +`.bss' + Switch to .bss section. Equivalent to `.section .bss' + +`.sbss' + Switch to .sbss section. Equivalent to `.section .sbss' + + +File: as.info, Node: MIPS-Dependent, Next: MMIX-Dependent, Prev: MicroBlaze-Dependent, Up: Machine Dependencies + +9.24 MIPS Dependent Features +============================ + + GNU `as' for MIPS architectures supports several different MIPS +processors, and MIPS ISA levels I through V, MIPS32, and MIPS64. For +information about the MIPS instruction set, see `MIPS RISC +Architecture', by Kane and Heindrich (Prentice-Hall). For an overview +of MIPS assembly conventions, see "Appendix D: Assembly Language +Programming" in the same work. + +* Menu: + +* MIPS Opts:: Assembler options +* MIPS Object:: ECOFF object code +* MIPS Stabs:: Directives for debugging information +* MIPS ISA:: Directives to override the ISA level +* MIPS symbol sizes:: Directives to override the size of symbols +* MIPS autoextend:: Directives for extending MIPS 16 bit instructions +* MIPS insn:: Directive to mark data as an instruction +* MIPS option stack:: Directives to save and restore options +* MIPS ASE instruction generation overrides:: Directives to control + generation of MIPS ASE instructions +* MIPS floating-point:: Directives to override floating-point options + + +File: as.info, Node: MIPS Opts, Next: MIPS Object, Up: MIPS-Dependent + +9.24.1 Assembler options +------------------------ + +The MIPS configurations of GNU `as' support these special options: + +`-G NUM' + This option sets the largest size of an object that can be + referenced implicitly with the `gp' register. It is only accepted + for targets that use ECOFF format. The default value is 8. + +`-EB' +`-EL' + Any MIPS configuration of `as' can select big-endian or + little-endian output at run time (unlike the other GNU development + tools, which must be configured for one or the other). Use `-EB' + to select big-endian output, and `-EL' for little-endian. + +`-KPIC' + Generate SVR4-style PIC. This option tells the assembler to + generate SVR4-style position-independent macro expansions. It + also tells the assembler to mark the output file as PIC. + +`-mvxworks-pic' + Generate VxWorks PIC. This option tells the assembler to generate + VxWorks-style position-independent macro expansions. + +`-mips1' +`-mips2' +`-mips3' +`-mips4' +`-mips5' +`-mips32' +`-mips32r2' +`-mips64' +`-mips64r2' + Generate code for a particular MIPS Instruction Set Architecture + level. `-mips1' corresponds to the R2000 and R3000 processors, + `-mips2' to the R6000 processor, `-mips3' to the R4000 processor, + and `-mips4' to the R8000 and R10000 processors. `-mips5', + `-mips32', `-mips32r2', `-mips64', and `-mips64r2' correspond to + generic MIPS V, MIPS32, MIPS32 RELEASE 2, MIPS64, and MIPS64 + RELEASE 2 ISA processors, respectively. You can also switch + instruction sets during the assembly; see *Note Directives to + override the ISA level: MIPS ISA. + +`-mgp32' +`-mfp32' + Some macros have different expansions for 32-bit and 64-bit + registers. The register sizes are normally inferred from the ISA + and ABI, but these flags force a certain group of registers to be + treated as 32 bits wide at all times. `-mgp32' controls the size + of general-purpose registers and `-mfp32' controls the size of + floating-point registers. + + The `.set gp=32' and `.set fp=32' directives allow the size of + registers to be changed for parts of an object. The default value + is restored by `.set gp=default' and `.set fp=default'. + + On some MIPS variants there is a 32-bit mode flag; when this flag + is set, 64-bit instructions generate a trap. Also, some 32-bit + OSes only save the 32-bit registers on a context switch, so it is + essential never to use the 64-bit registers. + +`-mgp64' +`-mfp64' + Assume that 64-bit registers are available. This is provided in + the interests of symmetry with `-mgp32' and `-mfp32'. + + The `.set gp=64' and `.set fp=64' directives allow the size of + registers to be changed for parts of an object. The default value + is restored by `.set gp=default' and `.set fp=default'. + +`-mips16' +`-no-mips16' + Generate code for the MIPS 16 processor. This is equivalent to + putting `.set mips16' at the start of the assembly file. + `-no-mips16' turns off this option. + +`-msmartmips' +`-mno-smartmips' + Enables the SmartMIPS extensions to the MIPS32 instruction set, + which provides a number of new instructions which target smartcard + and cryptographic applications. This is equivalent to putting + `.set smartmips' at the start of the assembly file. + `-mno-smartmips' turns off this option. + +`-mips3d' +`-no-mips3d' + Generate code for the MIPS-3D Application Specific Extension. + This tells the assembler to accept MIPS-3D instructions. + `-no-mips3d' turns off this option. + +`-mdmx' +`-no-mdmx' + Generate code for the MDMX Application Specific Extension. This + tells the assembler to accept MDMX instructions. `-no-mdmx' turns + off this option. + +`-mdsp' +`-mno-dsp' + Generate code for the DSP Release 1 Application Specific Extension. + This tells the assembler to accept DSP Release 1 instructions. + `-mno-dsp' turns off this option. + +`-mdspr2' +`-mno-dspr2' + Generate code for the DSP Release 2 Application Specific Extension. + This option implies -mdsp. This tells the assembler to accept DSP + Release 2 instructions. `-mno-dspr2' turns off this option. + +`-mmt' +`-mno-mt' + Generate code for the MT Application Specific Extension. This + tells the assembler to accept MT instructions. `-mno-mt' turns + off this option. + +`-mfix7000' +`-mno-fix7000' + Cause nops to be inserted if the read of the destination register + of an mfhi or mflo instruction occurs in the following two + instructions. + +`-mfix-vr4120' +`-no-mfix-vr4120' + Insert nops to work around certain VR4120 errata. This option is + intended to be used on GCC-generated code: it is not designed to + catch all problems in hand-written assembler code. + +`-mfix-vr4130' +`-no-mfix-vr4130' + Insert nops to work around the VR4130 `mflo'/`mfhi' errata. + +`-mfix-24k' +`-no-mfix-24k' + Insert nops to work around the 24K `eret'/`deret' errata. + +`-m4010' +`-no-m4010' + Generate code for the LSI R4010 chip. This tells the assembler to + accept the R4010 specific instructions (`addciu', `ffc', etc.), + and to not schedule `nop' instructions around accesses to the `HI' + and `LO' registers. `-no-m4010' turns off this option. + +`-m4650' +`-no-m4650' + Generate code for the MIPS R4650 chip. This tells the assembler + to accept the `mad' and `madu' instruction, and to not schedule + `nop' instructions around accesses to the `HI' and `LO' registers. + `-no-m4650' turns off this option. + +`-m3900' +`-no-m3900' +`-m4100' +`-no-m4100' + For each option `-mNNNN', generate code for the MIPS RNNNN chip. + This tells the assembler to accept instructions specific to that + chip, and to schedule for that chip's hazards. + +`-march=CPU' + Generate code for a particular MIPS cpu. It is exactly equivalent + to `-mCPU', except that there are more value of CPU understood. + Valid CPU value are: + + 2000, 3000, 3900, 4000, 4010, 4100, 4111, vr4120, vr4130, + vr4181, 4300, 4400, 4600, 4650, 5000, rm5200, rm5230, rm5231, + rm5261, rm5721, vr5400, vr5500, 6000, rm7000, 8000, rm9000, + 10000, 12000, 14000, 16000, 4kc, 4km, 4kp, 4ksc, 4kec, 4kem, + 4kep, 4ksd, m4k, m4kp, 24kc, 24kf2_1, 24kf, 24kf1_1, 24kec, + 24kef2_1, 24kef, 24kef1_1, 34kc, 34kf2_1, 34kf, 34kf1_1, 74kc, + 74kf2_1, 74kf, 74kf1_1, 74kf3_2, 1004kc, 1004kf2_1, 1004kf, + 1004kf1_1, 5kc, 5kf, 20kc, 25kf, sb1, sb1a, loongson2e, + loongson2f, octeon, xlr + + For compatibility reasons, `Nx' and `Bfx' are accepted as synonyms + for `Nf1_1'. These values are deprecated. + +`-mtune=CPU' + Schedule and tune for a particular MIPS cpu. Valid CPU values are + identical to `-march=CPU'. + +`-mabi=ABI' + Record which ABI the source code uses. The recognized arguments + are: `32', `n32', `o64', `64' and `eabi'. + +`-msym32' +`-mno-sym32' + Equivalent to adding `.set sym32' or `.set nosym32' to the + beginning of the assembler input. *Note MIPS symbol sizes::. + +`-nocpp' + This option is ignored. It is accepted for command-line + compatibility with other assemblers, which use it to turn off C + style preprocessing. With GNU `as', there is no need for + `-nocpp', because the GNU assembler itself never runs the C + preprocessor. + +`-msoft-float' +`-mhard-float' + Disable or enable floating-point instructions. Note that by + default floating-point instructions are always allowed even with + CPU targets that don't have support for these instructions. + +`-msingle-float' +`-mdouble-float' + Disable or enable double-precision floating-point operations. Note + that by default double-precision floating-point operations are + always allowed even with CPU targets that don't have support for + these operations. + +`--construct-floats' +`--no-construct-floats' + The `--no-construct-floats' option disables the construction of + double width floating point constants by loading the two halves of + the value into the two single width floating point registers that + make up the double width register. This feature is useful if the + processor support the FR bit in its status register, and this bit + is known (by the programmer) to be set. This bit prevents the + aliasing of the double width register by the single width + registers. + + By default `--construct-floats' is selected, allowing construction + of these floating point constants. + +`--trap' +`--no-break' + `as' automatically macro expands certain division and + multiplication instructions to check for overflow and division by + zero. This option causes `as' to generate code to take a trap + exception rather than a break exception when an error is detected. + The trap instructions are only supported at Instruction Set + Architecture level 2 and higher. + +`--break' +`--no-trap' + Generate code to take a break exception rather than a trap + exception when an error is detected. This is the default. + +`-mpdr' +`-mno-pdr' + Control generation of `.pdr' sections. Off by default on IRIX, on + elsewhere. + +`-mshared' +`-mno-shared' + When generating code using the Unix calling conventions (selected + by `-KPIC' or `-mcall_shared'), gas will normally generate code + which can go into a shared library. The `-mno-shared' option + tells gas to generate code which uses the calling convention, but + can not go into a shared library. The resulting code is slightly + more efficient. This option only affects the handling of the + `.cpload' and `.cpsetup' pseudo-ops. + + +File: as.info, Node: MIPS Object, Next: MIPS Stabs, Prev: MIPS Opts, Up: MIPS-Dependent + +9.24.2 MIPS ECOFF object code +----------------------------- + +Assembling for a MIPS ECOFF target supports some additional sections +besides the usual `.text', `.data' and `.bss'. The additional sections +are `.rdata', used for read-only data, `.sdata', used for small data, +and `.sbss', used for small common objects. + + When assembling for ECOFF, the assembler uses the `$gp' (`$28') +register to form the address of a "small object". Any object in the +`.sdata' or `.sbss' sections is considered "small" in this sense. For +external objects, or for objects in the `.bss' section, you can use the +`gcc' `-G' option to control the size of objects addressed via `$gp'; +the default value is 8, meaning that a reference to any object eight +bytes or smaller uses `$gp'. Passing `-G 0' to `as' prevents it from +using the `$gp' register on the basis of object size (but the assembler +uses `$gp' for objects in `.sdata' or `sbss' in any case). The size of +an object in the `.bss' section is set by the `.comm' or `.lcomm' +directive that defines it. The size of an external object may be set +with the `.extern' directive. For example, `.extern sym,4' declares +that the object at `sym' is 4 bytes in length, whie leaving `sym' +otherwise undefined. + + Using small ECOFF objects requires linker support, and assumes that +the `$gp' register is correctly initialized (normally done +automatically by the startup code). MIPS ECOFF assembly code must not +modify the `$gp' register. + + +File: as.info, Node: MIPS Stabs, Next: MIPS ISA, Prev: MIPS Object, Up: MIPS-Dependent + +9.24.3 Directives for debugging information +------------------------------------------- + +MIPS ECOFF `as' supports several directives used for generating +debugging information which are not support by traditional MIPS +assemblers. These are `.def', `.endef', `.dim', `.file', `.scl', +`.size', `.tag', `.type', `.val', `.stabd', `.stabn', and `.stabs'. +The debugging information generated by the three `.stab' directives can +only be read by GDB, not by traditional MIPS debuggers (this +enhancement is required to fully support C++ debugging). These +directives are primarily used by compilers, not assembly language +programmers! + + +File: as.info, Node: MIPS symbol sizes, Next: MIPS autoextend, Prev: MIPS ISA, Up: MIPS-Dependent + +9.24.4 Directives to override the size of symbols +------------------------------------------------- + +The n64 ABI allows symbols to have any 64-bit value. Although this +provides a great deal of flexibility, it means that some macros have +much longer expansions than their 32-bit counterparts. For example, +the non-PIC expansion of `dla $4,sym' is usually: + + lui $4,%highest(sym) + lui $1,%hi(sym) + daddiu $4,$4,%higher(sym) + daddiu $1,$1,%lo(sym) + dsll32 $4,$4,0 + daddu $4,$4,$1 + + whereas the 32-bit expansion is simply: + + lui $4,%hi(sym) + daddiu $4,$4,%lo(sym) + + n64 code is sometimes constructed in such a way that all symbolic +constants are known to have 32-bit values, and in such cases, it's +preferable to use the 32-bit expansion instead of the 64-bit expansion. + + You can use the `.set sym32' directive to tell the assembler that, +from this point on, all expressions of the form `SYMBOL' or `SYMBOL + +OFFSET' have 32-bit values. For example: + + .set sym32 + dla $4,sym + lw $4,sym+16 + sw $4,sym+0x8000($4) + + will cause the assembler to treat `sym', `sym+16' and `sym+0x8000' +as 32-bit values. The handling of non-symbolic addresses is not +affected. + + The directive `.set nosym32' ends a `.set sym32' block and reverts +to the normal behavior. It is also possible to change the symbol size +using the command-line options `-msym32' and `-mno-sym32'. + + These options and directives are always accepted, but at present, +they have no effect for anything other than n64. + + +File: as.info, Node: MIPS ISA, Next: MIPS symbol sizes, Prev: MIPS Stabs, Up: MIPS-Dependent + +9.24.5 Directives to override the ISA level +------------------------------------------- + +GNU `as' supports an additional directive to change the MIPS +Instruction Set Architecture level on the fly: `.set mipsN'. N should +be a number from 0 to 5, or 32, 32r2, 64 or 64r2. The values other +than 0 make the assembler accept instructions for the corresponding ISA +level, from that point on in the assembly. `.set mipsN' affects not +only which instructions are permitted, but also how certain macros are +expanded. `.set mips0' restores the ISA level to its original level: +either the level you selected with command line options, or the default +for your configuration. You can use this feature to permit specific +MIPS3 instructions while assembling in 32 bit mode. Use this directive +with care! + + The `.set arch=CPU' directive provides even finer control. It +changes the effective CPU target and allows the assembler to use +instructions specific to a particular CPU. All CPUs supported by the +`-march' command line option are also selectable by this directive. +The original value is restored by `.set arch=default'. + + The directive `.set mips16' puts the assembler into MIPS 16 mode, in +which it will assemble instructions for the MIPS 16 processor. Use +`.set nomips16' to return to normal 32 bit mode. + + Traditional MIPS assemblers do not support this directive. + + +File: as.info, Node: MIPS autoextend, Next: MIPS insn, Prev: MIPS symbol sizes, Up: MIPS-Dependent + +9.24.6 Directives for extending MIPS 16 bit instructions +-------------------------------------------------------- + +By default, MIPS 16 instructions are automatically extended to 32 bits +when necessary. The directive `.set noautoextend' will turn this off. +When `.set noautoextend' is in effect, any 32 bit instruction must be +explicitly extended with the `.e' modifier (e.g., `li.e $4,1000'). The +directive `.set autoextend' may be used to once again automatically +extend instructions when necessary. + + This directive is only meaningful when in MIPS 16 mode. Traditional +MIPS assemblers do not support this directive. + + +File: as.info, Node: MIPS insn, Next: MIPS option stack, Prev: MIPS autoextend, Up: MIPS-Dependent + +9.24.7 Directive to mark data as an instruction +----------------------------------------------- + +The `.insn' directive tells `as' that the following data is actually +instructions. This makes a difference in MIPS 16 mode: when loading +the address of a label which precedes instructions, `as' automatically +adds 1 to the value, so that jumping to the loaded address will do the +right thing. + + The `.global' and `.globl' directives supported by `as' will by +default mark the symbol as pointing to a region of data not code. This +means that, for example, any instructions following such a symbol will +not be disassembled by `objdump' as it will regard them as data. To +change this behaviour an optional section name can be placed after the +symbol name in the `.global' directive. If this section exists and is +known to be a code section, then the symbol will be marked as poiting at +code not data. Ie the syntax for the directive is: + + `.global SYMBOL[ SECTION][, SYMBOL[ SECTION]] ...', + + Here is a short example: + + .global foo .text, bar, baz .data + foo: + nop + bar: + .word 0x0 + baz: + .word 0x1 + + +File: as.info, Node: MIPS option stack, Next: MIPS ASE instruction generation overrides, Prev: MIPS insn, Up: MIPS-Dependent + +9.24.8 Directives to save and restore options +--------------------------------------------- + +The directives `.set push' and `.set pop' may be used to save and +restore the current settings for all the options which are controlled +by `.set'. The `.set push' directive saves the current settings on a +stack. The `.set pop' directive pops the stack and restores the +settings. + + These directives can be useful inside an macro which must change an +option such as the ISA level or instruction reordering but does not want +to change the state of the code which invoked the macro. + + Traditional MIPS assemblers do not support these directives. + + +File: as.info, Node: MIPS ASE instruction generation overrides, Next: MIPS floating-point, Prev: MIPS option stack, Up: MIPS-Dependent + +9.24.9 Directives to control generation of MIPS ASE instructions +---------------------------------------------------------------- + +The directive `.set mips3d' makes the assembler accept instructions +from the MIPS-3D Application Specific Extension from that point on in +the assembly. The `.set nomips3d' directive prevents MIPS-3D +instructions from being accepted. + + The directive `.set smartmips' makes the assembler accept +instructions from the SmartMIPS Application Specific Extension to the +MIPS32 ISA from that point on in the assembly. The `.set nosmartmips' +directive prevents SmartMIPS instructions from being accepted. + + The directive `.set mdmx' makes the assembler accept instructions +from the MDMX Application Specific Extension from that point on in the +assembly. The `.set nomdmx' directive prevents MDMX instructions from +being accepted. + + The directive `.set dsp' makes the assembler accept instructions +from the DSP Release 1 Application Specific Extension from that point +on in the assembly. The `.set nodsp' directive prevents DSP Release 1 +instructions from being accepted. + + The directive `.set dspr2' makes the assembler accept instructions +from the DSP Release 2 Application Specific Extension from that point +on in the assembly. This dirctive implies `.set dsp'. The `.set +nodspr2' directive prevents DSP Release 2 instructions from being +accepted. + + The directive `.set mt' makes the assembler accept instructions from +the MT Application Specific Extension from that point on in the +assembly. The `.set nomt' directive prevents MT instructions from +being accepted. + + Traditional MIPS assemblers do not support these directives. + + +File: as.info, Node: MIPS floating-point, Prev: MIPS ASE instruction generation overrides, Up: MIPS-Dependent + +9.24.10 Directives to override floating-point options +----------------------------------------------------- + +The directives `.set softfloat' and `.set hardfloat' provide finer +control of disabling and enabling float-point instructions. These +directives always override the default (that hard-float instructions +are accepted) or the command-line options (`-msoft-float' and +`-mhard-float'). + + The directives `.set singlefloat' and `.set doublefloat' provide +finer control of disabling and enabling double-precision float-point +operations. These directives always override the default (that +double-precision operations are accepted) or the command-line options +(`-msingle-float' and `-mdouble-float'). + + Traditional MIPS assemblers do not support these directives. + + +File: as.info, Node: MMIX-Dependent, Next: MSP430-Dependent, Prev: MIPS-Dependent, Up: Machine Dependencies + +9.25 MMIX Dependent Features +============================ + +* Menu: + +* MMIX-Opts:: Command-line Options +* MMIX-Expand:: Instruction expansion +* MMIX-Syntax:: Syntax +* MMIX-mmixal:: Differences to `mmixal' syntax and semantics + + +File: as.info, Node: MMIX-Opts, Next: MMIX-Expand, Up: MMIX-Dependent + +9.25.1 Command-line Options +--------------------------- + +The MMIX version of `as' has some machine-dependent options. + + When `--fixed-special-register-names' is specified, only the register +names specified in *Note MMIX-Regs:: are recognized in the instructions +`PUT' and `GET'. + + You can use the `--globalize-symbols' to make all symbols global. +This option is useful when splitting up a `mmixal' program into several +files. + + The `--gnu-syntax' turns off most syntax compatibility with +`mmixal'. Its usability is currently doubtful. + + The `--relax' option is not fully supported, but will eventually make +the object file prepared for linker relaxation. + + If you want to avoid inadvertently calling a predefined symbol and +would rather get an error, for example when using `as' with a compiler +or other machine-generated code, specify `--no-predefined-syms'. This +turns off built-in predefined definitions of all such symbols, +including rounding-mode symbols, segment symbols, `BIT' symbols, and +`TRAP' symbols used in `mmix' "system calls". It also turns off +predefined special-register names, except when used in `PUT' and `GET' +instructions. + + By default, some instructions are expanded to fit the size of the +operand or an external symbol (*note MMIX-Expand::). By passing +`--no-expand', no such expansion will be done, instead causing errors +at link time if the operand does not fit. + + The `mmixal' documentation (*note mmixsite::) specifies that global +registers allocated with the `GREG' directive (*note MMIX-greg::) and +initialized to the same non-zero value, will refer to the same global +register. This isn't strictly enforceable in `as' since the final +addresses aren't known until link-time, but it will do an effort unless +the `--no-merge-gregs' option is specified. (Register merging isn't +yet implemented in `ld'.) + + `as' will warn every time it expands an instruction to fit an +operand unless the option `-x' is specified. It is believed that this +behaviour is more useful than just mimicking `mmixal''s behaviour, in +which instructions are only expanded if the `-x' option is specified, +and assembly fails otherwise, when an instruction needs to be expanded. +It needs to be kept in mind that `mmixal' is both an assembler and +linker, while `as' will expand instructions that at link stage can be +contracted. (Though linker relaxation isn't yet implemented in `ld'.) +The option `-x' also imples `--linker-allocated-gregs'. + + If instruction expansion is enabled, `as' can expand a `PUSHJ' +instruction into a series of instructions. The shortest expansion is +to not expand it, but just mark the call as redirectable to a stub, +which `ld' creates at link-time, but only if the original `PUSHJ' +instruction is found not to reach the target. The stub consists of the +necessary instructions to form a jump to the target. This happens if +`as' can assert that the `PUSHJ' instruction can reach such a stub. +The option `--no-pushj-stubs' disables this shorter expansion, and the +longer series of instructions is then created at assembly-time. The +option `--no-stubs' is a synonym, intended for compatibility with +future releases, where generation of stubs for other instructions may +be implemented. + + Usually a two-operand-expression (*note GREG-base::) without a +matching `GREG' directive is treated as an error by `as'. When the +option `--linker-allocated-gregs' is in effect, they are instead passed +through to the linker, which will allocate as many global registers as +is needed. + + +File: as.info, Node: MMIX-Expand, Next: MMIX-Syntax, Prev: MMIX-Opts, Up: MMIX-Dependent + +9.25.2 Instruction expansion +---------------------------- + +When `as' encounters an instruction with an operand that is either not +known or does not fit the operand size of the instruction, `as' (and +`ld') will expand the instruction into a sequence of instructions +semantically equivalent to the operand fitting the instruction. +Expansion will take place for the following instructions: + +`GETA' + Expands to a sequence of four instructions: `SETL', `INCML', + `INCMH' and `INCH'. The operand must be a multiple of four. + +Conditional branches + A branch instruction is turned into a branch with the complemented + condition and prediction bit over five instructions; four + instructions setting `$255' to the operand value, which like with + `GETA' must be a multiple of four, and a final `GO $255,$255,0'. + +`PUSHJ' + Similar to expansion for conditional branches; four instructions + set `$255' to the operand value, followed by a `PUSHGO + $255,$255,0'. + +`JMP' + Similar to conditional branches and `PUSHJ'. The final instruction + is `GO $255,$255,0'. + + The linker `ld' is expected to shrink these expansions for code +assembled with `--relax' (though not currently implemented). + + +File: as.info, Node: MMIX-Syntax, Next: MMIX-mmixal, Prev: MMIX-Expand, Up: MMIX-Dependent + +9.25.3 Syntax +------------- + +The assembly syntax is supposed to be upward compatible with that +described in Sections 1.3 and 1.4 of `The Art of Computer Programming, +Volume 1'. Draft versions of those chapters as well as other MMIX +information is located at +`http://www-cs-faculty.stanford.edu/~knuth/mmix-news.html'. Most code +examples from the mmixal package located there should work unmodified +when assembled and linked as single files, with a few noteworthy +exceptions (*note MMIX-mmixal::). + + Before an instruction is emitted, the current location is aligned to +the next four-byte boundary. If a label is defined at the beginning of +the line, its value will be the aligned value. + + In addition to the traditional hex-prefix `0x', a hexadecimal number +can also be specified by the prefix character `#'. + + After all operands to an MMIX instruction or directive have been +specified, the rest of the line is ignored, treated as a comment. + +* Menu: + +* MMIX-Chars:: Special Characters +* MMIX-Symbols:: Symbols +* MMIX-Regs:: Register Names +* MMIX-Pseudos:: Assembler Directives + + +File: as.info, Node: MMIX-Chars, Next: MMIX-Symbols, Up: MMIX-Syntax + +9.25.3.1 Special Characters +........................... + +The characters `*' and `#' are line comment characters; each start a +comment at the beginning of a line, but only at the beginning of a +line. A `#' prefixes a hexadecimal number if found elsewhere on a line. + + Two other characters, `%' and `!', each start a comment anywhere on +the line. Thus you can't use the `modulus' and `not' operators in +expressions normally associated with these two characters. + + A `;' is a line separator, treated as a new-line, so separate +instructions can be specified on a single line. + + +File: as.info, Node: MMIX-Symbols, Next: MMIX-Regs, Prev: MMIX-Chars, Up: MMIX-Syntax + +9.25.3.2 Symbols +................ + +The character `:' is permitted in identifiers. There are two +exceptions to it being treated as any other symbol character: if a +symbol begins with `:', it means that the symbol is in the global +namespace and that the current prefix should not be prepended to that +symbol (*note MMIX-prefix::). The `:' is then not considered part of +the symbol. For a symbol in the label position (first on a line), a `:' +at the end of a symbol is silently stripped off. A label is permitted, +but not required, to be followed by a `:', as with many other assembly +formats. + + The character `@' in an expression, is a synonym for `.', the +current location. + + In addition to the common forward and backward local symbol formats +(*note Symbol Names::), they can be specified with upper-case `B' and +`F', as in `8B' and `9F'. A local label defined for the current +position is written with a `H' appended to the number: + 3H LDB $0,$1,2 + This and traditional local-label formats cannot be mixed: a label +must be defined and referred to using the same format. + + There's a minor caveat: just as for the ordinary local symbols, the +local symbols are translated into ordinary symbols using control +characters are to hide the ordinal number of the symbol. +Unfortunately, these symbols are not translated back in error messages. +Thus you may see confusing error messages when local symbols are used. +Control characters `\003' (control-C) and `\004' (control-D) are used +for the MMIX-specific local-symbol syntax. + + The symbol `Main' is handled specially; it is always global. + + By defining the symbols `__.MMIX.start..text' and +`__.MMIX.start..data', the address of respectively the `.text' and +`.data' segments of the final program can be defined, though when +linking more than one object file, the code or data in the object file +containing the symbol is not guaranteed to be start at that position; +just the final executable. *Note MMIX-loc::. + + +File: as.info, Node: MMIX-Regs, Next: MMIX-Pseudos, Prev: MMIX-Symbols, Up: MMIX-Syntax + +9.25.3.3 Register names +....................... + +Local and global registers are specified as `$0' to `$255'. The +recognized special register names are `rJ', `rA', `rB', `rC', `rD', +`rE', `rF', `rG', `rH', `rI', `rK', `rL', `rM', `rN', `rO', `rP', `rQ', +`rR', `rS', `rT', `rU', `rV', `rW', `rX', `rY', `rZ', `rBB', `rTT', +`rWW', `rXX', `rYY' and `rZZ'. A leading `:' is optional for special +register names. + + Local and global symbols can be equated to register names and used in +place of ordinary registers. + + Similarly for special registers, local and global symbols can be +used. Also, symbols equated from numbers and constant expressions are +allowed in place of a special register, except when either of the +options `--no-predefined-syms' and `--fixed-special-register-names' are +specified. Then only the special register names above are allowed for +the instructions having a special register operand; `GET' and `PUT'. + + +File: as.info, Node: MMIX-Pseudos, Prev: MMIX-Regs, Up: MMIX-Syntax + +9.25.3.4 Assembler Directives +............................. + +`LOC' + The `LOC' directive sets the current location to the value of the + operand field, which may include changing sections. If the + operand is a constant, the section is set to either `.data' if the + value is `0x2000000000000000' or larger, else it is set to `.text'. + Within a section, the current location may only be changed to + monotonically higher addresses. A LOC expression must be a + previously defined symbol or a "pure" constant. + + An example, which sets the label PREV to the current location, and + updates the current location to eight bytes forward: + prev LOC @+8 + + When a LOC has a constant as its operand, a symbol + `__.MMIX.start..text' or `__.MMIX.start..data' is defined + depending on the address as mentioned above. Each such symbol is + interpreted as special by the linker, locating the section at that + address. Note that if multiple files are linked, the first object + file with that section will be mapped to that address (not + necessarily the file with the LOC definition). + +`LOCAL' + Example: + LOCAL external_symbol + LOCAL 42 + .local asymbol + + This directive-operation generates a link-time assertion that the + operand does not correspond to a global register. The operand is + an expression that at link-time resolves to a register symbol or a + number. A number is treated as the register having that number. + There is one restriction on the use of this directive: the + pseudo-directive must be placed in a section with contents, code + or data. + +`IS' + The `IS' directive: + asymbol IS an_expression + sets the symbol `asymbol' to `an_expression'. A symbol may not be + set more than once using this directive. Local labels may be set + using this directive, for example: + 5H IS @+4 + +`GREG' + This directive reserves a global register, gives it an initial + value and optionally gives it a symbolic name. Some examples: + + areg GREG + breg GREG data_value + GREG data_buffer + .greg creg, another_data_value + + The symbolic register name can be used in place of a (non-special) + register. If a value isn't provided, it defaults to zero. Unless + the option `--no-merge-gregs' is specified, non-zero registers + allocated with this directive may be eliminated by `as'; another + register with the same value used in its place. Any of the + instructions `CSWAP', `GO', `LDA', `LDBU', `LDB', `LDHT', `LDOU', + `LDO', `LDSF', `LDTU', `LDT', `LDUNC', `LDVTS', `LDWU', `LDW', + `PREGO', `PRELD', `PREST', `PUSHGO', `STBU', `STB', `STCO', `STHT', + `STOU', `STSF', `STTU', `STT', `STUNC', `SYNCD', `SYNCID', can + have a value nearby an initial value in place of its second and + third operands. Here, "nearby" is defined as within the range + 0...255 from the initial value of such an allocated register. + + buffer1 BYTE 0,0,0,0,0 + buffer2 BYTE 0,0,0,0,0 + ... + GREG buffer1 + LDOU $42,buffer2 + In the example above, the `Y' field of the `LDOUI' instruction + (LDOU with a constant Z) will be replaced with the global register + allocated for `buffer1', and the `Z' field will have the value 5, + the offset from `buffer1' to `buffer2'. The result is equivalent + to this code: + buffer1 BYTE 0,0,0,0,0 + buffer2 BYTE 0,0,0,0,0 + ... + tmpreg GREG buffer1 + LDOU $42,tmpreg,(buffer2-buffer1) + + Global registers allocated with this directive are allocated in + order higher-to-lower within a file. Other than that, the exact + order of register allocation and elimination is undefined. For + example, the order is undefined when more than one file with such + directives are linked together. With the options `-x' and + `--linker-allocated-gregs', `GREG' directives for two-operand + cases like the one mentioned above can be omitted. Sufficient + global registers will then be allocated by the linker. + +`BYTE' + The `BYTE' directive takes a series of operands separated by a + comma. If an operand is a string (*note Strings::), each + character of that string is emitted as a byte. Other operands + must be constant expressions without forward references, in the + range 0...255. If you need operands having expressions with + forward references, use `.byte' (*note Byte::). An operand can be + omitted, defaulting to a zero value. + +`WYDE' +`TETRA' +`OCTA' + The directives `WYDE', `TETRA' and `OCTA' emit constants of two, + four and eight bytes size respectively. Before anything else + happens for the directive, the current location is aligned to the + respective constant-size boundary. If a label is defined at the + beginning of the line, its value will be that after the alignment. + A single operand can be omitted, defaulting to a zero value + emitted for the directive. Operands can be expressed as strings + (*note Strings::), in which case each character in the string is + emitted as a separate constant of the size indicated by the + directive. + +`PREFIX' + The `PREFIX' directive sets a symbol name prefix to be prepended to + all symbols (except local symbols, *note MMIX-Symbols::), that are + not prefixed with `:', until the next `PREFIX' directive. Such + prefixes accumulate. For example, + PREFIX a + PREFIX b + c IS 0 + defines a symbol `abc' with the value 0. + +`BSPEC' +`ESPEC' + A pair of `BSPEC' and `ESPEC' directives delimit a section of + special contents (without specified semantics). Example: + BSPEC 42 + TETRA 1,2,3 + ESPEC + The single operand to `BSPEC' must be number in the range 0...255. + The `BSPEC' number 80 is used by the GNU binutils implementation. + + +File: as.info, Node: MMIX-mmixal, Prev: MMIX-Syntax, Up: MMIX-Dependent + +9.25.4 Differences to `mmixal' +------------------------------ + +The binutils `as' and `ld' combination has a few differences in +function compared to `mmixal' (*note mmixsite::). + + The replacement of a symbol with a GREG-allocated register (*note +GREG-base::) is not handled the exactly same way in `as' as in +`mmixal'. This is apparent in the `mmixal' example file `inout.mms', +where different registers with different offsets, eventually yielding +the same address, are used in the first instruction. This type of +difference should however not affect the function of any program unless +it has specific assumptions about the allocated register number. + + Line numbers (in the `mmo' object format) are currently not +supported. + + Expression operator precedence is not that of mmixal: operator +precedence is that of the C programming language. It's recommended to +use parentheses to explicitly specify wanted operator precedence +whenever more than one type of operators are used. + + The serialize unary operator `&', the fractional division operator +`//', the logical not operator `!' and the modulus operator `%' are not +available. + + Symbols are not global by default, unless the option +`--globalize-symbols' is passed. Use the `.global' directive to +globalize symbols (*note Global::). + + Operand syntax is a bit stricter with `as' than `mmixal'. For +example, you can't say `addu 1,2,3', instead you must write `addu +$1,$2,3'. + + You can't LOC to a lower address than those already visited (i.e., +"backwards"). + + A LOC directive must come before any emitted code. + + Predefined symbols are visible as file-local symbols after use. (In +the ELF file, that is--the linked mmo file has no notion of a file-local +symbol.) + + Some mapping of constant expressions to sections in LOC expressions +is attempted, but that functionality is easily confused and should be +avoided unless compatibility with `mmixal' is required. A LOC +expression to `0x2000000000000000' or higher, maps to the `.data' +section and lower addresses map to the `.text' section (*note +MMIX-loc::). + + The code and data areas are each contiguous. Sparse programs with +far-away LOC directives will take up the same amount of space as a +contiguous program with zeros filled in the gaps between the LOC +directives. If you need sparse programs, you might try and get the +wanted effect with a linker script and splitting up the code parts into +sections (*note Section::). Assembly code for this, to be compatible +with `mmixal', would look something like: + .if 0 + LOC away_expression + .else + .section away,"ax" + .fi + `as' will not execute the LOC directive and `mmixal' ignores the +lines with `.'. This construct can be used generally to help +compatibility. + + Symbols can't be defined twice-not even to the same value. + + Instruction mnemonics are recognized case-insensitive, though the +`IS' and `GREG' pseudo-operations must be specified in upper-case +characters. + + There's no unicode support. + + The following is a list of programs in `mmix.tar.gz', available at +`http://www-cs-faculty.stanford.edu/~knuth/mmix-news.html', last +checked with the version dated 2001-08-25 (md5sum +c393470cfc86fac040487d22d2bf0172) that assemble with `mmixal' but do +not assemble with `as': + +`silly.mms' + LOC to a previous address. + +`sim.mms' + Redefines symbol `Done'. + +`test.mms' + Uses the serial operator `&'. + + +File: as.info, Node: MSP430-Dependent, Next: SH-Dependent, Prev: MMIX-Dependent, Up: Machine Dependencies + +9.26 MSP 430 Dependent Features +=============================== + +* Menu: + +* MSP430 Options:: Options +* MSP430 Syntax:: Syntax +* MSP430 Floating Point:: Floating Point +* MSP430 Directives:: MSP 430 Machine Directives +* MSP430 Opcodes:: Opcodes +* MSP430 Profiling Capability:: Profiling Capability + + +File: as.info, Node: MSP430 Options, Next: MSP430 Syntax, Up: MSP430-Dependent + +9.26.1 Options +-------------- + +`-m' + select the mpu arch. Currently has no effect. + +`-mP' + enables polymorph instructions handler. + +`-mQ' + enables relaxation at assembly time. DANGEROUS! + + + +File: as.info, Node: MSP430 Syntax, Next: MSP430 Floating Point, Prev: MSP430 Options, Up: MSP430-Dependent + +9.26.2 Syntax +------------- + +* Menu: + +* MSP430-Macros:: Macros +* MSP430-Chars:: Special Characters +* MSP430-Regs:: Register Names +* MSP430-Ext:: Assembler Extensions + + +File: as.info, Node: MSP430-Macros, Next: MSP430-Chars, Up: MSP430 Syntax + +9.26.2.1 Macros +............... + +The macro syntax used on the MSP 430 is like that described in the MSP +430 Family Assembler Specification. Normal `as' macros should still +work. + + Additional built-in macros are: + +`llo(exp)' + Extracts least significant word from 32-bit expression 'exp'. + +`lhi(exp)' + Extracts most significant word from 32-bit expression 'exp'. + +`hlo(exp)' + Extracts 3rd word from 64-bit expression 'exp'. + +`hhi(exp)' + Extracts 4rd word from 64-bit expression 'exp'. + + + They normally being used as an immediate source operand. + mov #llo(1), r10 ; == mov #1, r10 + mov #lhi(1), r10 ; == mov #0, r10 + + +File: as.info, Node: MSP430-Chars, Next: MSP430-Regs, Prev: MSP430-Macros, Up: MSP430 Syntax + +9.26.2.2 Special Characters +........................... + +`;' is the line comment character. + + The character `$' in jump instructions indicates current location and +implemented only for TI syntax compatibility. + + +File: as.info, Node: MSP430-Regs, Next: MSP430-Ext, Prev: MSP430-Chars, Up: MSP430 Syntax + +9.26.2.3 Register Names +....................... + +General-purpose registers are represented by predefined symbols of the +form `rN' (for global registers), where N represents a number between +`0' and `15'. The leading letters may be in either upper or lower +case; for example, `r13' and `R7' are both valid register names. + + Register names `PC', `SP' and `SR' cannot be used as register names +and will be treated as variables. Use `r0', `r1', and `r2' instead. + + +File: as.info, Node: MSP430-Ext, Prev: MSP430-Regs, Up: MSP430 Syntax + +9.26.2.4 Assembler Extensions +............................. + +`@rN' + As destination operand being treated as `0(rn)' + +`0(rN)' + As source operand being treated as `@rn' + +`jCOND +N' + Skips next N bytes followed by jump instruction and equivalent to + `jCOND $+N+2' + + + Also, there are some instructions, which cannot be found in other +assemblers. These are branch instructions, which has different opcodes +upon jump distance. They all got PC relative addressing mode. + +`beq label' + A polymorph instruction which is `jeq label' in case if jump + distance within allowed range for cpu's jump instruction. If not, + this unrolls into a sequence of + jne $+6 + br label + +`bne label' + A polymorph instruction which is `jne label' or `jeq +4; br label' + +`blt label' + A polymorph instruction which is `jl label' or `jge +4; br label' + +`bltn label' + A polymorph instruction which is `jn label' or `jn +2; jmp +4; br + label' + +`bltu label' + A polymorph instruction which is `jlo label' or `jhs +2; br label' + +`bge label' + A polymorph instruction which is `jge label' or `jl +4; br label' + +`bgeu label' + A polymorph instruction which is `jhs label' or `jlo +4; br label' + +`bgt label' + A polymorph instruction which is `jeq +2; jge label' or `jeq +6; + jl +4; br label' + +`bgtu label' + A polymorph instruction which is `jeq +2; jhs label' or `jeq +6; + jlo +4; br label' + +`bleu label' + A polymorph instruction which is `jeq label; jlo label' or `jeq + +2; jhs +4; br label' + +`ble label' + A polymorph instruction which is `jeq label; jl label' or `jeq + +2; jge +4; br label' + +`jump label' + A polymorph instruction which is `jmp label' or `br label' + + +File: as.info, Node: MSP430 Floating Point, Next: MSP430 Directives, Prev: MSP430 Syntax, Up: MSP430-Dependent + +9.26.3 Floating Point +--------------------- + +The MSP 430 family uses IEEE 32-bit floating-point numbers. + + +File: as.info, Node: MSP430 Directives, Next: MSP430 Opcodes, Prev: MSP430 Floating Point, Up: MSP430-Dependent + +9.26.4 MSP 430 Machine Directives +--------------------------------- + +`.file' + This directive is ignored; it is accepted for compatibility with + other MSP 430 assemblers. + + _Warning:_ in other versions of the GNU assembler, `.file' is + used for the directive called `.app-file' in the MSP 430 + support. + +`.line' + This directive is ignored; it is accepted for compatibility with + other MSP 430 assemblers. + +`.arch' + Currently this directive is ignored; it is accepted for + compatibility with other MSP 430 assemblers. + +`.profiler' + This directive instructs assembler to add new profile entry to the + object file. + + + +File: as.info, Node: MSP430 Opcodes, Next: MSP430 Profiling Capability, Prev: MSP430 Directives, Up: MSP430-Dependent + +9.26.5 Opcodes +-------------- + +`as' implements all the standard MSP 430 opcodes. No additional +pseudo-instructions are needed on this family. + + For information on the 430 machine instruction set, see `MSP430 +User's Manual, document slau049d', Texas Instrument, Inc. + + +File: as.info, Node: MSP430 Profiling Capability, Prev: MSP430 Opcodes, Up: MSP430-Dependent + +9.26.6 Profiling Capability +--------------------------- + +It is a performance hit to use gcc's profiling approach for this tiny +target. Even more - jtag hardware facility does not perform any +profiling functions. However we've got gdb's built-in simulator where +we can do anything. + + We define new section `.profiler' which holds all profiling +information. We define new pseudo operation `.profiler' which will +instruct assembler to add new profile entry to the object file. Profile +should take place at the present address. + + Pseudo operation format: + + `.profiler flags,function_to_profile [, cycle_corrector, extra]' + + where: + + `flags' is a combination of the following characters: + + `s' + function entry + + `x' + function exit + + `i' + function is in init section + + `f' + function is in fini section + + `l' + library call + + `c' + libc standard call + + `d' + stack value demand + + `I' + interrupt service routine + + `P' + prologue start + + `p' + prologue end + + `E' + epilogue start + + `e' + epilogue end + + `j' + long jump / sjlj unwind + + `a' + an arbitrary code fragment + + `t' + extra parameter saved (a constant value like frame size) + +`function_to_profile' + a function address + +`cycle_corrector' + a value which should be added to the cycle counter, zero if + omitted. + +`extra' + any extra parameter, zero if omitted. + + + For example: + .global fxx + .type fxx,@function + fxx: + .LFrameOffset_fxx=0x08 + .profiler "scdP", fxx ; function entry. + ; we also demand stack value to be saved + push r11 + push r10 + push r9 + push r8 + .profiler "cdpt",fxx,0, .LFrameOffset_fxx ; check stack value at this point + ; (this is a prologue end) + ; note, that spare var filled with + ; the farme size + mov r15,r8 + ... + .profiler cdE,fxx ; check stack + pop r8 + pop r9 + pop r10 + pop r11 + .profiler xcde,fxx,3 ; exit adds 3 to the cycle counter + ret ; cause 'ret' insn takes 3 cycles + + +File: as.info, Node: PDP-11-Dependent, Next: PJ-Dependent, Prev: SH64-Dependent, Up: Machine Dependencies + +9.27 PDP-11 Dependent Features +============================== + +* Menu: + +* PDP-11-Options:: Options +* PDP-11-Pseudos:: Assembler Directives +* PDP-11-Syntax:: DEC Syntax versus BSD Syntax +* PDP-11-Mnemonics:: Instruction Naming +* PDP-11-Synthetic:: Synthetic Instructions + + +File: as.info, Node: PDP-11-Options, Next: PDP-11-Pseudos, Up: PDP-11-Dependent + +9.27.1 Options +-------------- + +The PDP-11 version of `as' has a rich set of machine dependent options. + +9.27.1.1 Code Generation Options +................................ + +`-mpic | -mno-pic' + Generate position-independent (or position-dependent) code. + + The default is to generate position-independent code. + +9.27.1.2 Instruction Set Extension Options +.......................................... + +These options enables or disables the use of extensions over the base +line instruction set as introduced by the first PDP-11 CPU: the KA11. +Most options come in two variants: a `-m'EXTENSION that enables +EXTENSION, and a `-mno-'EXTENSION that disables EXTENSION. + + The default is to enable all extensions. + +`-mall | -mall-extensions' + Enable all instruction set extensions. + +`-mno-extensions' + Disable all instruction set extensions. + +`-mcis | -mno-cis' + Enable (or disable) the use of the commercial instruction set, + which consists of these instructions: `ADDNI', `ADDN', `ADDPI', + `ADDP', `ASHNI', `ASHN', `ASHPI', `ASHP', `CMPCI', `CMPC', + `CMPNI', `CMPN', `CMPPI', `CMPP', `CVTLNI', `CVTLN', `CVTLPI', + `CVTLP', `CVTNLI', `CVTNL', `CVTNPI', `CVTNP', `CVTPLI', `CVTPL', + `CVTPNI', `CVTPN', `DIVPI', `DIVP', `L2DR', `L3DR', `LOCCI', + `LOCC', `MATCI', `MATC', `MOVCI', `MOVC', `MOVRCI', `MOVRC', + `MOVTCI', `MOVTC', `MULPI', `MULP', `SCANCI', `SCANC', `SKPCI', + `SKPC', `SPANCI', `SPANC', `SUBNI', `SUBN', `SUBPI', and `SUBP'. + +`-mcsm | -mno-csm' + Enable (or disable) the use of the `CSM' instruction. + +`-meis | -mno-eis' + Enable (or disable) the use of the extended instruction set, which + consists of these instructions: `ASHC', `ASH', `DIV', `MARK', + `MUL', `RTT', `SOB' `SXT', and `XOR'. + +`-mfis | -mkev11' +`-mno-fis | -mno-kev11' + Enable (or disable) the use of the KEV11 floating-point + instructions: `FADD', `FDIV', `FMUL', and `FSUB'. + +`-mfpp | -mfpu | -mfp-11' +`-mno-fpp | -mno-fpu | -mno-fp-11' + Enable (or disable) the use of FP-11 floating-point instructions: + `ABSF', `ADDF', `CFCC', `CLRF', `CMPF', `DIVF', `LDCFF', `LDCIF', + `LDEXP', `LDF', `LDFPS', `MODF', `MULF', `NEGF', `SETD', `SETF', + `SETI', `SETL', `STCFF', `STCFI', `STEXP', `STF', `STFPS', `STST', + `SUBF', and `TSTF'. + +`-mlimited-eis | -mno-limited-eis' + Enable (or disable) the use of the limited extended instruction + set: `MARK', `RTT', `SOB', `SXT', and `XOR'. + + The -mno-limited-eis options also implies -mno-eis. + +`-mmfpt | -mno-mfpt' + Enable (or disable) the use of the `MFPT' instruction. + +`-mmultiproc | -mno-multiproc' + Enable (or disable) the use of multiprocessor instructions: + `TSTSET' and `WRTLCK'. + +`-mmxps | -mno-mxps' + Enable (or disable) the use of the `MFPS' and `MTPS' instructions. + +`-mspl | -mno-spl' + Enable (or disable) the use of the `SPL' instruction. + + Enable (or disable) the use of the microcode instructions: `LDUB', + `MED', and `XFC'. + +9.27.1.3 CPU Model Options +.......................... + +These options enable the instruction set extensions supported by a +particular CPU, and disables all other extensions. + +`-mka11' + KA11 CPU. Base line instruction set only. + +`-mkb11' + KB11 CPU. Enable extended instruction set and `SPL'. + +`-mkd11a' + KD11-A CPU. Enable limited extended instruction set. + +`-mkd11b' + KD11-B CPU. Base line instruction set only. + +`-mkd11d' + KD11-D CPU. Base line instruction set only. + +`-mkd11e' + KD11-E CPU. Enable extended instruction set, `MFPS', and `MTPS'. + +`-mkd11f | -mkd11h | -mkd11q' + KD11-F, KD11-H, or KD11-Q CPU. Enable limited extended + instruction set, `MFPS', and `MTPS'. + +`-mkd11k' + KD11-K CPU. Enable extended instruction set, `LDUB', `MED', + `MFPS', `MFPT', `MTPS', and `XFC'. + +`-mkd11z' + KD11-Z CPU. Enable extended instruction set, `CSM', `MFPS', + `MFPT', `MTPS', and `SPL'. + +`-mf11' + F11 CPU. Enable extended instruction set, `MFPS', `MFPT', and + `MTPS'. + +`-mj11' + J11 CPU. Enable extended instruction set, `CSM', `MFPS', `MFPT', + `MTPS', `SPL', `TSTSET', and `WRTLCK'. + +`-mt11' + T11 CPU. Enable limited extended instruction set, `MFPS', and + `MTPS'. + +9.27.1.4 Machine Model Options +.............................. + +These options enable the instruction set extensions supported by a +particular machine model, and disables all other extensions. + +`-m11/03' + Same as `-mkd11f'. + +`-m11/04' + Same as `-mkd11d'. + +`-m11/05 | -m11/10' + Same as `-mkd11b'. + +`-m11/15 | -m11/20' + Same as `-mka11'. + +`-m11/21' + Same as `-mt11'. + +`-m11/23 | -m11/24' + Same as `-mf11'. + +`-m11/34' + Same as `-mkd11e'. + +`-m11/34a' + Ame as `-mkd11e' `-mfpp'. + +`-m11/35 | -m11/40' + Same as `-mkd11a'. + +`-m11/44' + Same as `-mkd11z'. + +`-m11/45 | -m11/50 | -m11/55 | -m11/70' + Same as `-mkb11'. + +`-m11/53 | -m11/73 | -m11/83 | -m11/84 | -m11/93 | -m11/94' + Same as `-mj11'. + +`-m11/60' + Same as `-mkd11k'. + + +File: as.info, Node: PDP-11-Pseudos, Next: PDP-11-Syntax, Prev: PDP-11-Options, Up: PDP-11-Dependent + +9.27.2 Assembler Directives +--------------------------- + +The PDP-11 version of `as' has a few machine dependent assembler +directives. + +`.bss' + Switch to the `bss' section. + +`.even' + Align the location counter to an even number. + + +File: as.info, Node: PDP-11-Syntax, Next: PDP-11-Mnemonics, Prev: PDP-11-Pseudos, Up: PDP-11-Dependent + +9.27.3 PDP-11 Assembly Language Syntax +-------------------------------------- + +`as' supports both DEC syntax and BSD syntax. The only difference is +that in DEC syntax, a `#' character is used to denote an immediate +constants, while in BSD syntax the character for this purpose is `$'. + + general-purpose registers are named `r0' through `r7'. Mnemonic +alternatives for `r6' and `r7' are `sp' and `pc', respectively. + + Floating-point registers are named `ac0' through `ac3', or +alternatively `fr0' through `fr3'. + + Comments are started with a `#' or a `/' character, and extend to +the end of the line. (FIXME: clash with immediates?) + + +File: as.info, Node: PDP-11-Mnemonics, Next: PDP-11-Synthetic, Prev: PDP-11-Syntax, Up: PDP-11-Dependent + +9.27.4 Instruction Naming +------------------------- + +Some instructions have alternative names. + +`BCC' + `BHIS' + +`BCS' + `BLO' + +`L2DR' + `L2D' + +`L3DR' + `L3D' + +`SYS' + `TRAP' + + +File: as.info, Node: PDP-11-Synthetic, Prev: PDP-11-Mnemonics, Up: PDP-11-Dependent + +9.27.5 Synthetic Instructions +----------------------------- + +The `JBR' and `J'CC synthetic instructions are not supported yet. + + +File: as.info, Node: PJ-Dependent, Next: PPC-Dependent, Prev: PDP-11-Dependent, Up: Machine Dependencies + +9.28 picoJava Dependent Features +================================ + +* Menu: + +* PJ Options:: Options + + +File: as.info, Node: PJ Options, Up: PJ-Dependent + +9.28.1 Options +-------------- + +`as' has two additional command-line options for the picoJava +architecture. +`-ml' + This option selects little endian data output. + +`-mb' + This option selects big endian data output. + + +File: as.info, Node: PPC-Dependent, Next: S/390-Dependent, Prev: PJ-Dependent, Up: Machine Dependencies + +9.29 PowerPC Dependent Features +=============================== + +* Menu: + +* PowerPC-Opts:: Options +* PowerPC-Pseudo:: PowerPC Assembler Directives + + +File: as.info, Node: PowerPC-Opts, Next: PowerPC-Pseudo, Up: PPC-Dependent + +9.29.1 Options +-------------- + +The PowerPC chip family includes several successive levels, using the +same core instruction set, but including a few additional instructions +at each level. There are exceptions to this however. For details on +what instructions each variant supports, please see the chip's +architecture reference manual. + + The following table lists all available PowerPC options. + +`-mpwrx | -mpwr2' + Generate code for POWER/2 (RIOS2). + +`-mpwr' + Generate code for POWER (RIOS1) + +`-m601' + Generate code for PowerPC 601. + +`-mppc, -mppc32, -m603, -m604' + Generate code for PowerPC 603/604. + +`-m403, -m405' + Generate code for PowerPC 403/405. + +`-m440' + Generate code for PowerPC 440. BookE and some 405 instructions. + +`-m476' + Generate code for PowerPC 476. + +`-m7400, -m7410, -m7450, -m7455' + Generate code for PowerPC 7400/7410/7450/7455. + +`-m750cl' + Generate code for PowerPC 750CL. + +`-mppc64, -m620' + Generate code for PowerPC 620/625/630. + +`-me500, -me500x2' + Generate code for Motorola e500 core complex. + +`-mspe' + Generate code for Motorola SPE instructions. + +`-mppc64bridge' + Generate code for PowerPC 64, including bridge insns. + +`-mbooke' + Generate code for 32-bit BookE. + +`-ma2' + Generate code for A2 architecture. + +`-me300' + Generate code for PowerPC e300 family. + +`-maltivec' + Generate code for processors with AltiVec instructions. + +`-mvsx' + Generate code for processors with Vector-Scalar (VSX) instructions. + +`-mpower4' + Generate code for Power4 architecture. + +`-mpower5' + Generate code for Power5 architecture. + +`-mpower6' + Generate code for Power6 architecture. + +`-mpower7' + Generate code for Power7 architecture. + +`-mcell' + Generate code for Cell Broadband Engine architecture. + +`-mcom' + Generate code Power/PowerPC common instructions. + +`-many' + Generate code for any architecture (PWR/PWRX/PPC). + +`-mregnames' + Allow symbolic names for registers. + +`-mno-regnames' + Do not allow symbolic names for registers. + +`-mrelocatable' + Support for GCC's -mrelocatable option. + +`-mrelocatable-lib' + Support for GCC's -mrelocatable-lib option. + +`-memb' + Set PPC_EMB bit in ELF flags. + +`-mlittle, -mlittle-endian' + Generate code for a little endian machine. + +`-mbig, -mbig-endian' + Generate code for a big endian machine. + +`-msolaris' + Generate code for Solaris. + +`-mno-solaris' + Do not generate code for Solaris. + + +File: as.info, Node: PowerPC-Pseudo, Prev: PowerPC-Opts, Up: PPC-Dependent + +9.29.2 PowerPC Assembler Directives +----------------------------------- + +A number of assembler directives are available for PowerPC. The +following table is far from complete. + +`.machine "string"' + This directive allows you to change the machine for which code is + generated. `"string"' may be any of the -m cpu selection options + (without the -m) enclosed in double quotes, `"push"', or `"pop"'. + `.machine "push"' saves the currently selected cpu, which may be + restored with `.machine "pop"'. + + +File: as.info, Node: S/390-Dependent, Next: SCORE-Dependent, Prev: PPC-Dependent, Up: Machine Dependencies + +9.30 IBM S/390 Dependent Features +================================= + + The s390 version of `as' supports two architectures modes and seven +chip levels. The architecture modes are the Enterprise System +Architecture (ESA) and the newer z/Architecture mode. The chip levels +are g5, g6, z900, z990, z9-109, z9-ec and z10. + +* Menu: + +* s390 Options:: Command-line Options. +* s390 Characters:: Special Characters. +* s390 Syntax:: Assembler Instruction syntax. +* s390 Directives:: Assembler Directives. +* s390 Floating Point:: Floating Point. + + +File: as.info, Node: s390 Options, Next: s390 Characters, Up: S/390-Dependent + +9.30.1 Options +-------------- + +The following table lists all available s390 specific options: + +`-m31 | -m64' + Select 31- or 64-bit ABI implying a word size of 32- or 64-bit. + + These options are only available with the ELF object file format, + and require that the necessary BFD support has been included (on a + 31-bit platform you must add -enable-64-bit-bfd on the call to the + configure script to enable 64-bit usage and use s390x as target + platform). + +`-mesa | -mzarch' + Select the architecture mode, either the Enterprise System + Architecture (esa) mode or the z/Architecture mode (zarch). + + The 64-bit instructions are only available with the z/Architecture + mode. The combination of `-m64' and `-mesa' results in a warning + message. + +`-march=CPU' + This option specifies the target processor. The following + processor names are recognized: `g5', `g6', `z900', `z990', + `z9-109', `z9-ec' and `z10'. Assembling an instruction that is + not supported on the target processor results in an error message. + Do not specify `g5' or `g6' with `-mzarch'. + +`-mregnames' + Allow symbolic names for registers. + +`-mno-regnames' + Do not allow symbolic names for registers. + +`-mwarn-areg-zero' + Warn whenever the operand for a base or index register has been + specified but evaluates to zero. This can indicate the misuse of + general purpose register 0 as an address register. + + + +File: as.info, Node: s390 Characters, Next: s390 Syntax, Prev: s390 Options, Up: S/390-Dependent + +9.30.2 Special Characters +------------------------- + +`#' is the line comment character. + + +File: as.info, Node: s390 Syntax, Next: s390 Directives, Prev: s390 Characters, Up: S/390-Dependent + +9.30.3 Instruction syntax +------------------------- + +The assembler syntax closely follows the syntax outlined in Enterprise +Systems Architecture/390 Principles of Operation (SA22-7201) and the +z/Architecture Principles of Operation (SA22-7832). + + Each instruction has two major parts, the instruction mnemonic and +the instruction operands. The instruction format varies. + +* Menu: + +* s390 Register:: Register Naming +* s390 Mnemonics:: Instruction Mnemonics +* s390 Operands:: Instruction Operands +* s390 Formats:: Instruction Formats +* s390 Aliases:: Instruction Aliases +* s390 Operand Modifier:: Instruction Operand Modifier +* s390 Instruction Marker:: Instruction Marker +* s390 Literal Pool Entries:: Literal Pool Entries + + +File: as.info, Node: s390 Register, Next: s390 Mnemonics, Up: s390 Syntax + +9.30.3.1 Register naming +........................ + +The `as' recognizes a number of predefined symbols for the various +processor registers. A register specification in one of the instruction +formats is an unsigned integer between 0 and 15. The specific +instruction and the position of the register in the instruction format +denotes the type of the register. The register symbols are prefixed with +`%': + + %rN the 16 general purpose registers, 0 <= N <= 15 + %fN the 16 floating point registers, 0 <= N <= 15 + %aN the 16 access registers, 0 <= N <= 15 + %cN the 16 control registers, 0 <= N <= 15 + %lit an alias for the general purpose register %r13 + %sp an alias for the general purpose register %r15 + + +File: as.info, Node: s390 Mnemonics, Next: s390 Operands, Prev: s390 Register, Up: s390 Syntax + +9.30.3.2 Instruction Mnemonics +.............................. + +All instructions documented in the Principles of Operation are supported +with the mnemonic and order of operands as described. The instruction +mnemonic identifies the instruction format (*Note s390 Formats::) and +the specific operation code for the instruction. For example, the `lr' +mnemonic denotes the instruction format `RR' with the operation code +`0x18'. + + The definition of the various mnemonics follows a scheme, where the +first character usually hint at the type of the instruction: + + a add instruction, for example `al' for add logical 32-bit + b branch instruction, for example `bc' for branch on condition + c compare or convert instruction, for example `cr' for compare + register 32-bit + d divide instruction, for example `dlr' devide logical register + 64-bit to 32-bit + i insert instruction, for example `ic' insert character + l load instruction, for example `ltr' load and test register + mv move instruction, for example `mvc' move character + m multiply instruction, for example `mh' multiply halfword + n and instruction, for example `ni' and immediate + o or instruction, for example `oc' or character + sla, sll shift left single instruction + sra, srl shift right single instruction + st store instruction, for example `stm' store multiple + s subtract instruction, for example `slr' subtract + logical 32-bit + t test or translate instruction, of example `tm' test under mask + x exclusive or instruction, for example `xc' exclusive or + character + + Certain characters at the end of the mnemonic may describe a property +of the instruction: + + c the instruction uses a 8-bit character operand + f the instruction extends a 32-bit operand to 64 bit + g the operands are treated as 64-bit values + h the operand uses a 16-bit halfword operand + i the instruction uses an immediate operand + l the instruction uses unsigned, logical operands + m the instruction uses a mask or operates on multiple values + r if r is the last character, the instruction operates on registers + y the instruction uses 20-bit displacements + + There are many exceptions to the scheme outlined in the above lists, +in particular for the priviledged instructions. For non-priviledged +instruction it works quite well, for example the instruction `clgfr' c: +compare instruction, l: unsigned operands, g: 64-bit operands, f: 32- +to 64-bit extension, r: register operands. The instruction compares an +64-bit value in a register with the zero extended 32-bit value from a +second register. For a complete list of all mnemonics see appendix B +in the Principles of Operation. + + +File: as.info, Node: s390 Operands, Next: s390 Formats, Prev: s390 Mnemonics, Up: s390 Syntax + +9.30.3.3 Instruction Operands +............................. + +Instruction operands can be grouped into three classes, operands located +in registers, immediate operands, and operands in storage. + + A register operand can be located in general, floating-point, access, +or control register. The register is identified by a four-bit field. +The field containing the register operand is called the R field. + + Immediate operands are contained within the instruction and can have +8, 16 or 32 bits. The field containing the immediate operand is called +the I field. Dependent on the instruction the I field is either signed +or unsigned. + + A storage operand consists of an address and a length. The address +of a storage operands can be specified in any of these ways: + + * The content of a single general R + + * The sum of the content of a general register called the base + register B plus the content of a displacement field D + + * The sum of the contents of two general registers called the index + register X and the base register B plus the content of a + displacement field + + * The sum of the current instruction address and a 32-bit signed + immediate field multiplied by two. + + The length of a storage operand can be: + + * Implied by the instruction + + * Specified by a bitmask + + * Specified by a four-bit or eight-bit length field L + + * Specified by the content of a general register + + The notation for storage operand addresses formed from multiple +fields is as follows: + +`Dn(Bn)' + the address for operand number n is formed from the content of + general register Bn called the base register and the displacement + field Dn. + +`Dn(Xn,Bn)' + the address for operand number n is formed from the content of + general register Xn called the index register, general register Bn + called the base register and the displacement field Dn. + +`Dn(Ln,Bn)' + the address for operand number n is formed from the content of + general regiser Bn called the base register and the displacement + field Dn. The length of the operand n is specified by the field + Ln. + + The base registers Bn and the index registers Xn of a storage +operand can be skipped. If Bn and Xn are skipped, a zero will be stored +to the operand field. The notation changes as follows: + + full notation short notation + ------------------------------------------ + Dn(0,Bn) Dn(Bn) + Dn(0,0) Dn + Dn(0) Dn + Dn(Ln,0) Dn(Ln) + + +File: as.info, Node: s390 Formats, Next: s390 Aliases, Prev: s390 Operands, Up: s390 Syntax + +9.30.3.4 Instruction Formats +............................ + +The Principles of Operation manuals lists 26 instruction formats where +some of the formats have multiple variants. For the `.insn' pseudo +directive the assembler recognizes some of the formats. Typically, the +most general variant of the instruction format is used by the `.insn' +directive. + + The following table lists the abbreviations used in the table of +instruction formats: + + OpCode / OpCd Part of the op code. + Bx Base register number for operand x. + Dx Displacement for operand x. + DLx Displacement lower 12 bits for operand x. + DHx Displacement higher 8-bits for operand x. + Rx Register number for operand x. + Xx Index register number for operand x. + Ix Signed immediate for operand x. + Ux Unsigned immediate for operand x. + + An instruction is two, four, or six bytes in length and must be +aligned on a 2 byte boundary. The first two bits of the instruction +specify the length of the instruction, 00 indicates a two byte +instruction, 01 and 10 indicates a four byte instruction, and 11 +indicates a six byte instruction. + + The following table lists the s390 instruction formats that are +available with the `.insn' pseudo directive: + +`E format' + + +-------------+ + | OpCode | + +-------------+ + 0 15 + +`RI format: <insn> R1,I2' + + +--------+----+----+------------------+ + | OpCode | R1 |OpCd| I2 | + +--------+----+----+------------------+ + 0 8 12 16 31 + +`RIE format: <insn> R1,R3,I2' + + +--------+----+----+------------------+--------+--------+ + | OpCode | R1 | R3 | I2 |////////| OpCode | + +--------+----+----+------------------+--------+--------+ + 0 8 12 16 32 40 47 + +`RIL format: <insn> R1,I2' + + +--------+----+----+------------------------------------+ + | OpCode | R1 |OpCd| I2 | + +--------+----+----+------------------------------------+ + 0 8 12 16 47 + +`RILU format: <insn> R1,U2' + + +--------+----+----+------------------------------------+ + | OpCode | R1 |OpCd| U2 | + +--------+----+----+------------------------------------+ + 0 8 12 16 47 + +`RIS format: <insn> R1,I2,M3,D4(B4)' + + +--------+----+----+----+-------------+--------+--------+ + | OpCode | R1 | M3 | B4 | D4 | I2 | Opcode | + +--------+----+----+----+-------------+--------+--------+ + 0 8 12 16 20 32 36 47 + +`RR format: <insn> R1,R2' + + +--------+----+----+ + | OpCode | R1 | R2 | + +--------+----+----+ + 0 8 12 15 + +`RRE format: <insn> R1,R2' + + +------------------+--------+----+----+ + | OpCode |////////| R1 | R2 | + +------------------+--------+----+----+ + 0 16 24 28 31 + +`RRF format: <insn> R1,R2,R3,M4' + + +------------------+----+----+----+----+ + | OpCode | R3 | M4 | R1 | R2 | + +------------------+----+----+----+----+ + 0 16 20 24 28 31 + +`RRS format: <insn> R1,R2,M3,D4(B4)' + + +--------+----+----+----+-------------+----+----+--------+ + | OpCode | R1 | R3 | B4 | D4 | M3 |////| OpCode | + +--------+----+----+----+-------------+----+----+--------+ + 0 8 12 16 20 32 36 40 47 + +`RS format: <insn> R1,R3,D2(B2)' + + +--------+----+----+----+-------------+ + | OpCode | R1 | R3 | B2 | D2 | + +--------+----+----+----+-------------+ + 0 8 12 16 20 31 + +`RSE format: <insn> R1,R3,D2(B2)' + + +--------+----+----+----+-------------+--------+--------+ + | OpCode | R1 | R3 | B2 | D2 |////////| OpCode | + +--------+----+----+----+-------------+--------+--------+ + 0 8 12 16 20 32 40 47 + +`RSI format: <insn> R1,R3,I2' + + +--------+----+----+------------------------------------+ + | OpCode | R1 | R3 | I2 | + +--------+----+----+------------------------------------+ + 0 8 12 16 47 + +`RSY format: <insn> R1,R3,D2(B2)' + + +--------+----+----+----+-------------+--------+--------+ + | OpCode | R1 | R3 | B2 | DL2 | DH2 | OpCode | + +--------+----+----+----+-------------+--------+--------+ + 0 8 12 16 20 32 40 47 + +`RX format: <insn> R1,D2(X2,B2)' + + +--------+----+----+----+-------------+ + | OpCode | R1 | X2 | B2 | D2 | + +--------+----+----+----+-------------+ + 0 8 12 16 20 31 + +`RXE format: <insn> R1,D2(X2,B2)' + + +--------+----+----+----+-------------+--------+--------+ + | OpCode | R1 | X2 | B2 | D2 |////////| OpCode | + +--------+----+----+----+-------------+--------+--------+ + 0 8 12 16 20 32 40 47 + +`RXF format: <insn> R1,R3,D2(X2,B2)' + + +--------+----+----+----+-------------+----+---+--------+ + | OpCode | R3 | X2 | B2 | D2 | R1 |///| OpCode | + +--------+----+----+----+-------------+----+---+--------+ + 0 8 12 16 20 32 36 40 47 + +`RXY format: <insn> R1,D2(X2,B2)' + + +--------+----+----+----+-------------+--------+--------+ + | OpCode | R1 | X2 | B2 | DL2 | DH2 | OpCode | + +--------+----+----+----+-------------+--------+--------+ + 0 8 12 16 20 32 36 40 47 + +`S format: <insn> D2(B2)' + + +------------------+----+-------------+ + | OpCode | B2 | D2 | + +------------------+----+-------------+ + 0 16 20 31 + +`SI format: <insn> D1(B1),I2' + + +--------+---------+----+-------------+ + | OpCode | I2 | B1 | D1 | + +--------+---------+----+-------------+ + 0 8 16 20 31 + +`SIY format: <insn> D1(B1),U2' + + +--------+---------+----+-------------+--------+--------+ + | OpCode | I2 | B1 | DL1 | DH1 | OpCode | + +--------+---------+----+-------------+--------+--------+ + 0 8 16 20 32 36 40 47 + +`SIL format: <insn> D1(B1),I2' + + +------------------+----+-------------+-----------------+ + | OpCode | B1 | D1 | I2 | + +------------------+----+-------------+-----------------+ + 0 16 20 32 47 + +`SS format: <insn> D1(R1,B1),D2(B3),R3' + + +--------+----+----+----+-------------+----+------------+ + | OpCode | R1 | R3 | B1 | D1 | B2 | D2 | + +--------+----+----+----+-------------+----+------------+ + 0 8 12 16 20 32 36 47 + +`SSE format: <insn> D1(B1),D2(B2)' + + +------------------+----+-------------+----+------------+ + | OpCode | B1 | D1 | B2 | D2 | + +------------------+----+-------------+----+------------+ + 0 8 12 16 20 32 36 47 + +`SSF format: <insn> D1(B1),D2(B2),R3' + + +--------+----+----+----+-------------+----+------------+ + | OpCode | R3 |OpCd| B1 | D1 | B2 | D2 | + +--------+----+----+----+-------------+----+------------+ + 0 8 12 16 20 32 36 47 + + + For the complete list of all instruction format variants see the +Principles of Operation manuals. + + +File: as.info, Node: s390 Aliases, Next: s390 Operand Modifier, Prev: s390 Formats, Up: s390 Syntax + +9.30.3.5 Instruction Aliases +............................ + +A specific bit pattern can have multiple mnemonics, for example the bit +pattern `0xa7000000' has the mnemonics `tmh' and `tmlh'. In addition, +there are a number of mnemonics recognized by `as' that are not present +in the Principles of Operation. These are the short forms of the +branch instructions, where the condition code mask operand is encoded +in the mnemonic. This is relevant for the branch instructions, the +compare and branch instructions, and the compare and trap instructions. + + For the branch instructions there are 20 condition code strings that +can be used as part of the mnemonic in place of a mask operand in the +instruction format: + + instruction short form + ------------------------------------------ + bcr M1,R2 b<m>r R2 + bc M1,D2(X2,B2) b<m> D2(X2,B2) + brc M1,I2 j<m> I2 + brcl M1,I2 jg<m> I2 + + In the mnemonic for a branch instruction the condition code string +<m> can be any of the following: + + o jump on overflow / if ones + h jump on A high + p jump on plus + nle jump on not low or equal + l jump on A low + m jump on minus + nhe jump on not high or equal + lh jump on low or high + ne jump on A not equal B + nz jump on not zero / if not zeros + e jump on A equal B + z jump on zero / if zeroes + nlh jump on not low or high + he jump on high or equal + nl jump on A not low + nm jump on not minus / if not mixed + le jump on low or equal + nh jump on A not high + np jump on not plus + no jump on not overflow / if not ones + + For the compare and branch, and compare and trap instructions there +are 12 condition code strings that can be used as part of the mnemonic +in place of a mask operand in the instruction format: + + instruction short form + -------------------------------------------------------- + crb R1,R2,M3,D4(B4) crb<m> R1,R2,D4(B4) + cgrb R1,R2,M3,D4(B4) cgrb<m> R1,R2,D4(B4) + crj R1,R2,M3,I4 crj<m> R1,R2,I4 + cgrj R1,R2,M3,I4 cgrj<m> R1,R2,I4 + cib R1,I2,M3,D4(B4) cib<m> R1,I2,D4(B4) + cgib R1,I2,M3,D4(B4) cgib<m> R1,I2,D4(B4) + cij R1,I2,M3,I4 cij<m> R1,I2,I4 + cgij R1,I2,M3,I4 cgij<m> R1,I2,I4 + crt R1,R2,M3 crt<m> R1,R2 + cgrt R1,R2,M3 cgrt<m> R1,R2 + cit R1,I2,M3 cit<m> R1,I2 + cgit R1,I2,M3 cgit<m> R1,I2 + clrb R1,R2,M3,D4(B4) clrb<m> R1,R2,D4(B4) + clgrb R1,R2,M3,D4(B4) clgrb<m> R1,R2,D4(B4) + clrj R1,R2,M3,I4 clrj<m> R1,R2,I4 + clgrj R1,R2,M3,I4 clgrj<m> R1,R2,I4 + clib R1,I2,M3,D4(B4) clib<m> R1,I2,D4(B4) + clgib R1,I2,M3,D4(B4) clgib<m> R1,I2,D4(B4) + clij R1,I2,M3,I4 clij<m> R1,I2,I4 + clgij R1,I2,M3,I4 clgij<m> R1,I2,I4 + clrt R1,R2,M3 clrt<m> R1,R2 + clgrt R1,R2,M3 clgrt<m> R1,R2 + clfit R1,I2,M3 clfit<m> R1,I2 + clgit R1,I2,M3 clgit<m> R1,I2 + + In the mnemonic for a compare and branch and compare and trap +instruction the condition code string <m> can be any of the following: + + h jump on A high + nle jump on not low or equal + l jump on A low + nhe jump on not high or equal + ne jump on A not equal B + lh jump on low or high + e jump on A equal B + nlh jump on not low or high + nl jump on A not low + he jump on high or equal + nh jump on A not high + le jump on low or equal + + +File: as.info, Node: s390 Operand Modifier, Next: s390 Instruction Marker, Prev: s390 Aliases, Up: s390 Syntax + +9.30.3.6 Instruction Operand Modifier +..................................... + +If a symbol modifier is attached to a symbol in an expression for an +instruction operand field, the symbol term is replaced with a reference +to an object in the global offset table (GOT) or the procedure linkage +table (PLT). The following expressions are allowed: `symbol@modifier + +constant', `symbol@modifier + label + constant', and `symbol@modifier - +label + constant'. The term `symbol' is the symbol that will be +entered into the GOT or PLT, `label' is a local label, and `constant' +is an arbitrary expression that the assembler can evaluate to a +constant value. + + The term `(symbol + constant1)@modifier +/- label + constant2' is +also accepted but a warning message is printed and the term is +converted to `symbol@modifier +/- label + constant1 + constant2'. + +`@got' +`@got12' + The @got modifier can be used for displacement fields, 16-bit + immediate fields and 32-bit pc-relative immediate fields. The + @got12 modifier is synonym to @got. The symbol is added to the + GOT. For displacement fields and 16-bit immediate fields the + symbol term is replaced with the offset from the start of the GOT + to the GOT slot for the symbol. For a 32-bit pc-relative field + the pc-relative offset to the GOT slot from the current + instruction address is used. + +`@gotent' + The @gotent modifier can be used for 32-bit pc-relative immediate + fields. The symbol is added to the GOT and the symbol term is + replaced with the pc-relative offset from the current instruction + to the GOT slot for the symbol. + +`@gotoff' + The @gotoff modifier can be used for 16-bit immediate fields. The + symbol term is replaced with the offset from the start of the GOT + to the address of the symbol. + +`@gotplt' + The @gotplt modifier can be used for displacement fields, 16-bit + immediate fields, and 32-bit pc-relative immediate fields. A + procedure linkage table entry is generated for the symbol and a + jump slot for the symbol is added to the GOT. For displacement + fields and 16-bit immediate fields the symbol term is replaced + with the offset from the start of the GOT to the jump slot for the + symbol. For a 32-bit pc-relative field the pc-relative offset to + the jump slot from the current instruction address is used. + +`@plt' + The @plt modifier can be used for 16-bit and 32-bit pc-relative + immediate fields. A procedure linkage table entry is generated for + the symbol. The symbol term is replaced with the relative offset + from the current instruction to the PLT entry for the symbol. + +`@pltoff' + The @pltoff modifier can be used for 16-bit immediate fields. The + symbol term is replaced with the offset from the start of the PLT + to the address of the symbol. + +`@gotntpoff' + The @gotntpoff modifier can be used for displacement fields. The + symbol is added to the static TLS block and the negated offset to + the symbol in the static TLS block is added to the GOT. The symbol + term is replaced with the offset to the GOT slot from the start of + the GOT. + +`@indntpoff' + The @indntpoff modifier can be used for 32-bit pc-relative + immediate fields. The symbol is added to the static TLS block and + the negated offset to the symbol in the static TLS block is added + to the GOT. The symbol term is replaced with the pc-relative + offset to the GOT slot from the current instruction address. + + For more information about the thread local storage modifiers +`gotntpoff' and `indntpoff' see the ELF extension documentation `ELF +Handling For Thread-Local Storage'. + + +File: as.info, Node: s390 Instruction Marker, Next: s390 Literal Pool Entries, Prev: s390 Operand Modifier, Up: s390 Syntax + +9.30.3.7 Instruction Marker +........................... + +The thread local storage instruction markers are used by the linker to +perform code optimization. + +`:tls_load' + The :tls_load marker is used to flag the load instruction in the + initial exec TLS model that retrieves the offset from the thread + pointer to a thread local storage variable from the GOT. + +`:tls_gdcall' + The :tls_gdcall marker is used to flag the branch-and-save + instruction to the __tls_get_offset function in the global dynamic + TLS model. + +`:tls_ldcall' + The :tls_ldcall marker is used to flag the branch-and-save + instruction to the __tls_get_offset function in the local dynamic + TLS model. + + For more information about the thread local storage instruction +marker and the linker optimizations see the ELF extension documentation +`ELF Handling For Thread-Local Storage'. + + +File: as.info, Node: s390 Literal Pool Entries, Prev: s390 Instruction Marker, Up: s390 Syntax + +9.30.3.8 Literal Pool Entries +............................. + +A literal pool is a collection of values. To access the values a pointer +to the literal pool is loaded to a register, the literal pool register. +Usually, register %r13 is used as the literal pool register (*Note s390 +Register::). Literal pool entries are created by adding the suffix +:lit1, :lit2, :lit4, or :lit8 to the end of an expression for an +instruction operand. The expression is added to the literal pool and the +operand is replaced with the offset to the literal in the literal pool. + +`:lit1' + The literal pool entry is created as an 8-bit value. An operand + modifier must not be used for the original expression. + +`:lit2' + The literal pool entry is created as a 16 bit value. The operand + modifier @got may be used in the original expression. The term + `x@got:lit2' will put the got offset for the global symbol x to + the literal pool as 16 bit value. + +`:lit4' + The literal pool entry is created as a 32-bit value. The operand + modifier @got and @plt may be used in the original expression. The + term `x@got:lit4' will put the got offset for the global symbol x + to the literal pool as a 32-bit value. The term `x@plt:lit4' will + put the plt offset for the global symbol x to the literal pool as + a 32-bit value. + +`:lit8' + The literal pool entry is created as a 64-bit value. The operand + modifier @got and @plt may be used in the original expression. The + term `x@got:lit8' will put the got offset for the global symbol x + to the literal pool as a 64-bit value. The term `x@plt:lit8' will + put the plt offset for the global symbol x to the literal pool as + a 64-bit value. + + The assembler directive `.ltorg' is used to emit all literal pool +entries to the current position. + + +File: as.info, Node: s390 Directives, Next: s390 Floating Point, Prev: s390 Syntax, Up: S/390-Dependent + +9.30.4 Assembler Directives +--------------------------- + +`as' for s390 supports all of the standard ELF assembler directives as +outlined in the main part of this document. Some directives have been +extended and there are some additional directives, which are only +available for the s390 `as'. + +`.insn' + This directive permits the numeric representation of an + instructions and makes the assembler insert the operands according + to one of the instructions formats for `.insn' (*Note s390 + Formats::). For example, the instruction `l %r1,24(%r15)' could + be written as `.insn rx,0x58000000,%r1,24(%r15)'. + +`.short' +`.long' +`.quad' + This directive places one or more 16-bit (.short), 32-bit (.long), + or 64-bit (.quad) values into the current section. If an ELF or + TLS modifier is used only the following expressions are allowed: + `symbol@modifier + constant', `symbol@modifier + label + + constant', and `symbol@modifier - label + constant'. The + following modifiers are available: + `@got' + `@got12' + The @got modifier can be used for .short, .long and .quad. + The @got12 modifier is synonym to @got. The symbol is added + to the GOT. The symbol term is replaced with offset from the + start of the GOT to the GOT slot for the symbol. + + `@gotoff' + The @gotoff modifier can be used for .short, .long and .quad. + The symbol term is replaced with the offset from the start of + the GOT to the address of the symbol. + + `@gotplt' + The @gotplt modifier can be used for .long and .quad. A + procedure linkage table entry is generated for the symbol and + a jump slot for the symbol is added to the GOT. The symbol + term is replaced with the offset from the start of the GOT to + the jump slot for the symbol. + + `@plt' + The @plt modifier can be used for .long and .quad. A + procedure linkage table entry us generated for the symbol. + The symbol term is replaced with the address of the PLT entry + for the symbol. + + `@pltoff' + The @pltoff modifier can be used for .short, .long and .quad. + The symbol term is replaced with the offset from the start of + the PLT to the address of the symbol. + + `@tlsgd' + `@tlsldm' + The @tlsgd and @tlsldm modifier can be used for .long and + .quad. A tls_index structure for the symbol is added to the + GOT. The symbol term is replaced with the offset from the + start of the GOT to the tls_index structure. + + `@gotntpoff' + `@indntpoff' + The @gotntpoff and @indntpoff modifier can be used for .long + and .quad. The symbol is added to the static TLS block and + the negated offset to the symbol in the static TLS block is + added to the GOT. For @gotntpoff the symbol term is replaced + with the offset from the start of the GOT to the GOT slot, + for @indntpoff the symbol term is replaced with the address + of the GOT slot. + + `@dtpoff' + The @dtpoff modifier can be used for .long and .quad. The + symbol term is replaced with the offset of the symbol + relative to the start of the TLS block it is contained in. + + `@ntpoff' + The @ntpoff modifier can be used for .long and .quad. The + symbol term is replaced with the offset of the symbol + relative to the TCB pointer. + + For more information about the thread local storage modifiers see + the ELF extension documentation `ELF Handling For Thread-Local + Storage'. + +`.ltorg' + This directive causes the current contents of the literal pool to + be dumped to the current location (*Note s390 Literal Pool + Entries::). + + +File: as.info, Node: s390 Floating Point, Prev: s390 Directives, Up: S/390-Dependent + +9.30.5 Floating Point +--------------------- + +The assembler recognizes both the IEEE floating-point instruction and +the hexadecimal floating-point instructions. The floating-point +constructors `.float', `.single', and `.double' always emit the IEEE +format. To assemble hexadecimal floating-point constants the `.long' +and `.quad' directives must be used. + + +File: as.info, Node: SCORE-Dependent, Next: Sparc-Dependent, Prev: S/390-Dependent, Up: Machine Dependencies + +9.31 SCORE Dependent Features +============================= + +* Menu: + +* SCORE-Opts:: Assembler options +* SCORE-Pseudo:: SCORE Assembler Directives + + +File: as.info, Node: SCORE-Opts, Next: SCORE-Pseudo, Up: SCORE-Dependent + +9.31.1 Options +-------------- + +The following table lists all available SCORE options. + +`-G NUM' + This option sets the largest size of an object that can be + referenced implicitly with the `gp' register. The default value is + 8. + +`-EB' + Assemble code for a big-endian cpu + +`-EL' + Assemble code for a little-endian cpu + +`-FIXDD' + Assemble code for fix data dependency + +`-NWARN' + Assemble code for no warning message for fix data dependency + +`-SCORE5' + Assemble code for target is SCORE5 + +`-SCORE5U' + Assemble code for target is SCORE5U + +`-SCORE7' + Assemble code for target is SCORE7, this is default setting + +`-SCORE3' + Assemble code for target is SCORE3 + +`-march=score7' + Assemble code for target is SCORE7, this is default setting + +`-march=score3' + Assemble code for target is SCORE3 + +`-USE_R1' + Assemble code for no warning message when using temp register r1 + +`-KPIC' + Generate code for PIC. This option tells the assembler to generate + score position-independent macro expansions. It also tells the + assembler to mark the output file as PIC. + +`-O0' + Assembler will not perform any optimizations + +`-V' + Sunplus release version + + + +File: as.info, Node: SCORE-Pseudo, Prev: SCORE-Opts, Up: SCORE-Dependent + +9.31.2 SCORE Assembler Directives +--------------------------------- + +A number of assembler directives are available for SCORE. The +following table is far from complete. + +`.set nwarn' + Let the assembler not to generate warnings if the source machine + language instructions happen data dependency. + +`.set fixdd' + Let the assembler to insert bubbles (32 bit nop instruction / 16 + bit nop! Instruction) if the source machine language instructions + happen data dependency. + +`.set nofixdd' + Let the assembler to generate warnings if the source machine + language instructions happen data dependency. (Default) + +`.set r1' + Let the assembler not to generate warnings if the source program + uses r1. allow user to use r1 + +`set nor1' + Let the assembler to generate warnings if the source program uses + r1. (Default) + +`.sdata' + Tell the assembler to add subsequent data into the sdata section + +`.rdata' + Tell the assembler to add subsequent data into the rdata section + +`.frame "frame-register", "offset", "return-pc-register"' + Describe a stack frame. "frame-register" is the frame register, + "offset" is the distance from the frame register to the virtual + frame pointer, "return-pc-register" is the return program register. + You must use ".ent" before ".frame" and only one ".frame" can be + used per ".ent". + +`.mask "bitmask", "frameoffset"' + Indicate which of the integer registers are saved in the current + function's stack frame, this is for the debugger to explain the + frame chain. + +`.ent "proc-name"' + Set the beginning of the procedure "proc_name". Use this directive + when you want to generate information for the debugger. + +`.end proc-name' + Set the end of a procedure. Use this directive to generate + information for the debugger. + +`.bss' + Switch the destination of following statements into the bss + section, which is used for data that is uninitialized anywhere. + + + +File: as.info, Node: SH-Dependent, Next: SH64-Dependent, Prev: MSP430-Dependent, Up: Machine Dependencies + +9.32 Renesas / SuperH SH Dependent Features +=========================================== + +* Menu: + +* SH Options:: Options +* SH Syntax:: Syntax +* SH Floating Point:: Floating Point +* SH Directives:: SH Machine Directives +* SH Opcodes:: Opcodes + + +File: as.info, Node: SH Options, Next: SH Syntax, Up: SH-Dependent + +9.32.1 Options +-------------- + +`as' has following command-line options for the Renesas (formerly +Hitachi) / SuperH SH family. + +`--little' + Generate little endian code. + +`--big' + Generate big endian code. + +`--relax' + Alter jump instructions for long displacements. + +`--small' + Align sections to 4 byte boundaries, not 16. + +`--dsp' + Enable sh-dsp insns, and disable sh3e / sh4 insns. + +`--renesas' + Disable optimization with section symbol for compatibility with + Renesas assembler. + +`--allow-reg-prefix' + Allow '$' as a register name prefix. + +`--isa=sh4 | sh4a' + Specify the sh4 or sh4a instruction set. + +`--isa=dsp' + Enable sh-dsp insns, and disable sh3e / sh4 insns. + +`--isa=fp' + Enable sh2e, sh3e, sh4, and sh4a insn sets. + +`--isa=all' + Enable sh1, sh2, sh2e, sh3, sh3e, sh4, sh4a, and sh-dsp insn sets. + +`-h-tick-hex' + Support H'00 style hex constants in addition to 0x00 style. + + + +File: as.info, Node: SH Syntax, Next: SH Floating Point, Prev: SH Options, Up: SH-Dependent + +9.32.2 Syntax +------------- + +* Menu: + +* SH-Chars:: Special Characters +* SH-Regs:: Register Names +* SH-Addressing:: Addressing Modes + + +File: as.info, Node: SH-Chars, Next: SH-Regs, Up: SH Syntax + +9.32.2.1 Special Characters +........................... + +`!' is the line comment character. + + You can use `;' instead of a newline to separate statements. + + Since `$' has no special meaning, you may use it in symbol names. + + +File: as.info, Node: SH-Regs, Next: SH-Addressing, Prev: SH-Chars, Up: SH Syntax + +9.32.2.2 Register Names +....................... + +You can use the predefined symbols `r0', `r1', `r2', `r3', `r4', `r5', +`r6', `r7', `r8', `r9', `r10', `r11', `r12', `r13', `r14', and `r15' to +refer to the SH registers. + + The SH also has these control registers: + +`pr' + procedure register (holds return address) + +`pc' + program counter + +`mach' +`macl' + high and low multiply accumulator registers + +`sr' + status register + +`gbr' + global base register + +`vbr' + vector base register (for interrupt vectors) + + +File: as.info, Node: SH-Addressing, Prev: SH-Regs, Up: SH Syntax + +9.32.2.3 Addressing Modes +......................... + +`as' understands the following addressing modes for the SH. `RN' in +the following refers to any of the numbered registers, but _not_ the +control registers. + +`RN' + Register direct + +`@RN' + Register indirect + +`@-RN' + Register indirect with pre-decrement + +`@RN+' + Register indirect with post-increment + +`@(DISP, RN)' + Register indirect with displacement + +`@(R0, RN)' + Register indexed + +`@(DISP, GBR)' + `GBR' offset + +`@(R0, GBR)' + GBR indexed + +`ADDR' +`@(DISP, PC)' + PC relative address (for branch or for addressing memory). The + `as' implementation allows you to use the simpler form ADDR + anywhere a PC relative address is called for; the alternate form + is supported for compatibility with other assemblers. + +`#IMM' + Immediate data + + +File: as.info, Node: SH Floating Point, Next: SH Directives, Prev: SH Syntax, Up: SH-Dependent + +9.32.3 Floating Point +--------------------- + +SH2E, SH3E and SH4 groups have on-chip floating-point unit (FPU). Other +SH groups can use `.float' directive to generate IEEE floating-point +numbers. + + SH2E and SH3E support single-precision floating point calculations as +well as entirely PCAPI compatible emulation of double-precision +floating point calculations. SH2E and SH3E instructions are a subset of +the floating point calculations conforming to the IEEE754 standard. + + In addition to single-precision and double-precision floating-point +operation capability, the on-chip FPU of SH4 has a 128-bit graphic +engine that enables 32-bit floating-point data to be processed 128 bits +at a time. It also supports 4 * 4 array operations and inner product +operations. Also, a superscalar architecture is employed that enables +simultaneous execution of two instructions (including FPU +instructions), providing performance of up to twice that of +conventional architectures at the same frequency. + + +File: as.info, Node: SH Directives, Next: SH Opcodes, Prev: SH Floating Point, Up: SH-Dependent + +9.32.4 SH Machine Directives +---------------------------- + +`uaword' +`ualong' + `as' will issue a warning when a misaligned `.word' or `.long' + directive is used. You may use `.uaword' or `.ualong' to indicate + that the value is intentionally misaligned. + + +File: as.info, Node: SH Opcodes, Prev: SH Directives, Up: SH-Dependent + +9.32.5 Opcodes +-------------- + +For detailed information on the SH machine instruction set, see +`SH-Microcomputer User's Manual' (Renesas) or `SH-4 32-bit CPU Core +Architecture' (SuperH) and `SuperH (SH) 64-Bit RISC Series' (SuperH). + + `as' implements all the standard SH opcodes. No additional +pseudo-instructions are needed on this family. Note, however, that +because `as' supports a simpler form of PC-relative addressing, you may +simply write (for example) + + mov.l bar,r0 + +where other assemblers might require an explicit displacement to `bar' +from the program counter: + + mov.l @(DISP, PC) + + Here is a summary of SH opcodes: + + Legend: + Rn a numbered register + Rm another numbered register + #imm immediate data + disp displacement + disp8 8-bit displacement + disp12 12-bit displacement + + add #imm,Rn lds.l @Rn+,PR + add Rm,Rn mac.w @Rm+,@Rn+ + addc Rm,Rn mov #imm,Rn + addv Rm,Rn mov Rm,Rn + and #imm,R0 mov.b Rm,@(R0,Rn) + and Rm,Rn mov.b Rm,@-Rn + and.b #imm,@(R0,GBR) mov.b Rm,@Rn + bf disp8 mov.b @(disp,Rm),R0 + bra disp12 mov.b @(disp,GBR),R0 + bsr disp12 mov.b @(R0,Rm),Rn + bt disp8 mov.b @Rm+,Rn + clrmac mov.b @Rm,Rn + clrt mov.b R0,@(disp,Rm) + cmp/eq #imm,R0 mov.b R0,@(disp,GBR) + cmp/eq Rm,Rn mov.l Rm,@(disp,Rn) + cmp/ge Rm,Rn mov.l Rm,@(R0,Rn) + cmp/gt Rm,Rn mov.l Rm,@-Rn + cmp/hi Rm,Rn mov.l Rm,@Rn + cmp/hs Rm,Rn mov.l @(disp,Rn),Rm + cmp/pl Rn mov.l @(disp,GBR),R0 + cmp/pz Rn mov.l @(disp,PC),Rn + cmp/str Rm,Rn mov.l @(R0,Rm),Rn + div0s Rm,Rn mov.l @Rm+,Rn + div0u mov.l @Rm,Rn + div1 Rm,Rn mov.l R0,@(disp,GBR) + exts.b Rm,Rn mov.w Rm,@(R0,Rn) + exts.w Rm,Rn mov.w Rm,@-Rn + extu.b Rm,Rn mov.w Rm,@Rn + extu.w Rm,Rn mov.w @(disp,Rm),R0 + jmp @Rn mov.w @(disp,GBR),R0 + jsr @Rn mov.w @(disp,PC),Rn + ldc Rn,GBR mov.w @(R0,Rm),Rn + ldc Rn,SR mov.w @Rm+,Rn + ldc Rn,VBR mov.w @Rm,Rn + ldc.l @Rn+,GBR mov.w R0,@(disp,Rm) + ldc.l @Rn+,SR mov.w R0,@(disp,GBR) + ldc.l @Rn+,VBR mova @(disp,PC),R0 + lds Rn,MACH movt Rn + lds Rn,MACL muls Rm,Rn + lds Rn,PR mulu Rm,Rn + lds.l @Rn+,MACH neg Rm,Rn + lds.l @Rn+,MACL negc Rm,Rn + + nop stc VBR,Rn + not Rm,Rn stc.l GBR,@-Rn + or #imm,R0 stc.l SR,@-Rn + or Rm,Rn stc.l VBR,@-Rn + or.b #imm,@(R0,GBR) sts MACH,Rn + rotcl Rn sts MACL,Rn + rotcr Rn sts PR,Rn + rotl Rn sts.l MACH,@-Rn + rotr Rn sts.l MACL,@-Rn + rte sts.l PR,@-Rn + rts sub Rm,Rn + sett subc Rm,Rn + shal Rn subv Rm,Rn + shar Rn swap.b Rm,Rn + shll Rn swap.w Rm,Rn + shll16 Rn tas.b @Rn + shll2 Rn trapa #imm + shll8 Rn tst #imm,R0 + shlr Rn tst Rm,Rn + shlr16 Rn tst.b #imm,@(R0,GBR) + shlr2 Rn xor #imm,R0 + shlr8 Rn xor Rm,Rn + sleep xor.b #imm,@(R0,GBR) + stc GBR,Rn xtrct Rm,Rn + stc SR,Rn + + +File: as.info, Node: SH64-Dependent, Next: PDP-11-Dependent, Prev: SH-Dependent, Up: Machine Dependencies + +9.33 SuperH SH64 Dependent Features +=================================== + +* Menu: + +* SH64 Options:: Options +* SH64 Syntax:: Syntax +* SH64 Directives:: SH64 Machine Directives +* SH64 Opcodes:: Opcodes + + +File: as.info, Node: SH64 Options, Next: SH64 Syntax, Up: SH64-Dependent + +9.33.1 Options +-------------- + +`-isa=sh4 | sh4a' + Specify the sh4 or sh4a instruction set. + +`-isa=dsp' + Enable sh-dsp insns, and disable sh3e / sh4 insns. + +`-isa=fp' + Enable sh2e, sh3e, sh4, and sh4a insn sets. + +`-isa=all' + Enable sh1, sh2, sh2e, sh3, sh3e, sh4, sh4a, and sh-dsp insn sets. + +`-isa=shmedia | -isa=shcompact' + Specify the default instruction set. `SHmedia' specifies the + 32-bit opcodes, and `SHcompact' specifies the 16-bit opcodes + compatible with previous SH families. The default depends on the + ABI selected; the default for the 64-bit ABI is SHmedia, and the + default for the 32-bit ABI is SHcompact. If neither the ABI nor + the ISA is specified, the default is 32-bit SHcompact. + + Note that the `.mode' pseudo-op is not permitted if the ISA is not + specified on the command line. + +`-abi=32 | -abi=64' + Specify the default ABI. If the ISA is specified and the ABI is + not, the default ABI depends on the ISA, with SHmedia defaulting + to 64-bit and SHcompact defaulting to 32-bit. + + Note that the `.abi' pseudo-op is not permitted if the ABI is not + specified on the command line. When the ABI is specified on the + command line, any `.abi' pseudo-ops in the source must match it. + +`-shcompact-const-crange' + Emit code-range descriptors for constants in SHcompact code + sections. + +`-no-mix' + Disallow SHmedia code in the same section as constants and + SHcompact code. + +`-no-expand' + Do not expand MOVI, PT, PTA or PTB instructions. + +`-expand-pt32' + With -abi=64, expand PT, PTA and PTB instructions to 32 bits only. + +`-h-tick-hex' + Support H'00 style hex constants in addition to 0x00 style. + + + +File: as.info, Node: SH64 Syntax, Next: SH64 Directives, Prev: SH64 Options, Up: SH64-Dependent + +9.33.2 Syntax +------------- + +* Menu: + +* SH64-Chars:: Special Characters +* SH64-Regs:: Register Names +* SH64-Addressing:: Addressing Modes + + +File: as.info, Node: SH64-Chars, Next: SH64-Regs, Up: SH64 Syntax + +9.33.2.1 Special Characters +........................... + +`!' is the line comment character. + + You can use `;' instead of a newline to separate statements. + + Since `$' has no special meaning, you may use it in symbol names. + + +File: as.info, Node: SH64-Regs, Next: SH64-Addressing, Prev: SH64-Chars, Up: SH64 Syntax + +9.33.2.2 Register Names +....................... + +You can use the predefined symbols `r0' through `r63' to refer to the +SH64 general registers, `cr0' through `cr63' for control registers, +`tr0' through `tr7' for target address registers, `fr0' through `fr63' +for single-precision floating point registers, `dr0' through `dr62' +(even numbered registers only) for double-precision floating point +registers, `fv0' through `fv60' (multiples of four only) for +single-precision floating point vectors, `fp0' through `fp62' (even +numbered registers only) for single-precision floating point pairs, +`mtrx0' through `mtrx48' (multiples of 16 only) for 4x4 matrices of +single-precision floating point registers, `pc' for the program +counter, and `fpscr' for the floating point status and control register. + + You can also refer to the control registers by the mnemonics `sr', +`ssr', `pssr', `intevt', `expevt', `pexpevt', `tra', `spc', `pspc', +`resvec', `vbr', `tea', `dcr', `kcr0', `kcr1', `ctc', and `usr'. + + +File: as.info, Node: SH64-Addressing, Prev: SH64-Regs, Up: SH64 Syntax + +9.33.2.3 Addressing Modes +......................... + +SH64 operands consist of either a register or immediate value. The +immediate value can be a constant or label reference (or portion of a +label reference), as in this example: + + movi 4,r2 + pt function, tr4 + movi (function >> 16) & 65535,r0 + shori function & 65535, r0 + ld.l r0,4,r0 + + Instruction label references can reference labels in either SHmedia +or SHcompact. To differentiate between the two, labels in SHmedia +sections will always have the least significant bit set (i.e. they will +be odd), which SHcompact labels will have the least significant bit +reset (i.e. they will be even). If you need to reference the actual +address of a label, you can use the `datalabel' modifier, as in this +example: + + .long function + .long datalabel function + + In that example, the first longword may or may not have the least +significant bit set depending on whether the label is an SHmedia label +or an SHcompact label. The second longword will be the actual address +of the label, regardless of what type of label it is. + + +File: as.info, Node: SH64 Directives, Next: SH64 Opcodes, Prev: SH64 Syntax, Up: SH64-Dependent + +9.33.3 SH64 Machine Directives +------------------------------ + +In addition to the SH directives, the SH64 provides the following +directives: + +`.mode [shmedia|shcompact]' +`.isa [shmedia|shcompact]' + Specify the ISA for the following instructions (the two directives + are equivalent). Note that programs such as `objdump' rely on + symbolic labels to determine when such mode switches occur (by + checking the least significant bit of the label's address), so + such mode/isa changes should always be followed by a label (in + practice, this is true anyway). Note that you cannot use these + directives if you didn't specify an ISA on the command line. + +`.abi [32|64]' + Specify the ABI for the following instructions. Note that you + cannot use this directive unless you specified an ABI on the + command line, and the ABIs specified must match. + +`.uaquad' + Like .uaword and .ualong, this allows you to specify an + intentionally unaligned quadword (64 bit word). + + + +File: as.info, Node: SH64 Opcodes, Prev: SH64 Directives, Up: SH64-Dependent + +9.33.4 Opcodes +-------------- + +For detailed information on the SH64 machine instruction set, see +`SuperH 64 bit RISC Series Architecture Manual' (SuperH, Inc.). + + `as' implements all the standard SH64 opcodes. In addition, the +following pseudo-opcodes may be expanded into one or more alternate +opcodes: + +`movi' + If the value doesn't fit into a standard `movi' opcode, `as' will + replace the `movi' with a sequence of `movi' and `shori' opcodes. + +`pt' + This expands to a sequence of `movi' and `shori' opcode, followed + by a `ptrel' opcode, or to a `pta' or `ptb' opcode, depending on + the label referenced. + + + +File: as.info, Node: Sparc-Dependent, Next: TIC54X-Dependent, Prev: SCORE-Dependent, Up: Machine Dependencies + +9.34 SPARC Dependent Features +============================= + +* Menu: + +* Sparc-Opts:: Options +* Sparc-Aligned-Data:: Option to enforce aligned data +* Sparc-Syntax:: Syntax +* Sparc-Float:: Floating Point +* Sparc-Directives:: Sparc Machine Directives + + +File: as.info, Node: Sparc-Opts, Next: Sparc-Aligned-Data, Up: Sparc-Dependent + +9.34.1 Options +-------------- + +The SPARC chip family includes several successive versions, using the +same core instruction set, but including a few additional instructions +at each version. There are exceptions to this however. For details on +what instructions each variant supports, please see the chip's +architecture reference manual. + + By default, `as' assumes the core instruction set (SPARC v6), but +"bumps" the architecture level as needed: it switches to successively +higher architectures as it encounters instructions that only exist in +the higher levels. + + If not configured for SPARC v9 (`sparc64-*-*') GAS will not bump +past sparclite by default, an option must be passed to enable the v9 +instructions. + + GAS treats sparclite as being compatible with v8, unless an +architecture is explicitly requested. SPARC v9 is always incompatible +with sparclite. + +`-Av6 | -Av7 | -Av8 | -Asparclet | -Asparclite' +`-Av8plus | -Av8plusa | -Av9 | -Av9a' + Use one of the `-A' options to select one of the SPARC + architectures explicitly. If you select an architecture + explicitly, `as' reports a fatal error if it encounters an + instruction or feature requiring an incompatible or higher level. + + `-Av8plus' and `-Av8plusa' select a 32 bit environment. + + `-Av9' and `-Av9a' select a 64 bit environment and are not + available unless GAS is explicitly configured with 64 bit + environment support. + + `-Av8plusa' and `-Av9a' enable the SPARC V9 instruction set with + UltraSPARC extensions. + +`-xarch=v8plus | -xarch=v8plusa' + For compatibility with the SunOS v9 assembler. These options are + equivalent to -Av8plus and -Av8plusa, respectively. + +`-bump' + Warn whenever it is necessary to switch to another level. If an + architecture level is explicitly requested, GAS will not issue + warnings until that level is reached, and will then bump the level + as required (except between incompatible levels). + +`-32 | -64' + Select the word size, either 32 bits or 64 bits. These options + are only available with the ELF object file format, and require + that the necessary BFD support has been included. + + +File: as.info, Node: Sparc-Aligned-Data, Next: Sparc-Syntax, Prev: Sparc-Opts, Up: Sparc-Dependent + +9.34.2 Enforcing aligned data +----------------------------- + +SPARC GAS normally permits data to be misaligned. For example, it +permits the `.long' pseudo-op to be used on a byte boundary. However, +the native SunOS assemblers issue an error when they see misaligned +data. + + You can use the `--enforce-aligned-data' option to make SPARC GAS +also issue an error about misaligned data, just as the SunOS assemblers +do. + + The `--enforce-aligned-data' option is not the default because gcc +issues misaligned data pseudo-ops when it initializes certain packed +data structures (structures defined using the `packed' attribute). You +may have to assemble with GAS in order to initialize packed data +structures in your own code. + + +File: as.info, Node: Sparc-Syntax, Next: Sparc-Float, Prev: Sparc-Aligned-Data, Up: Sparc-Dependent + +9.34.3 Sparc Syntax +------------------- + +The assembler syntax closely follows The Sparc Architecture Manual, +versions 8 and 9, as well as most extensions defined by Sun for their +UltraSPARC and Niagara line of processors. + +* Menu: + +* Sparc-Chars:: Special Characters +* Sparc-Regs:: Register Names +* Sparc-Constants:: Constant Names +* Sparc-Relocs:: Relocations +* Sparc-Size-Translations:: Size Translations + + +File: as.info, Node: Sparc-Chars, Next: Sparc-Regs, Up: Sparc-Syntax + +9.34.3.1 Special Characters +........................... + +`#' is the line comment character. + + `;' can be used instead of a newline to separate statements. + + +File: as.info, Node: Sparc-Regs, Next: Sparc-Constants, Prev: Sparc-Chars, Up: Sparc-Syntax + +9.34.3.2 Register Names +....................... + +The Sparc integer register file is broken down into global, outgoing, +local, and incoming. + + * The 8 global registers are referred to as `%gN'. + + * The 8 outgoing registers are referred to as `%oN'. + + * The 8 local registers are referred to as `%lN'. + + * The 8 incoming registers are referred to as `%iN'. + + * The frame pointer register `%i6' can be referenced using the alias + `%fp'. + + * The stack pointer register `%o6' can be referenced using the alias + `%sp'. + + Floating point registers are simply referred to as `%fN'. When +assembling for pre-V9, only 32 floating point registers are available. +For V9 and later there are 64, but there are restrictions when +referencing the upper 32 registers. They can only be accessed as +double or quad, and thus only even or quad numbered accesses are +allowed. For example, `%f34' is a legal floating point register, but +`%f35' is not. + + Certain V9 instructions allow access to ancillary state registers. +Most simply they can be referred to as `%asrN' where N can be from 16 +to 31. However, there are some aliases defined to reference ASR +registers defined for various UltraSPARC processors: + + * The tick compare register is referred to as `%tick_cmpr'. + + * The system tick register is referred to as `%stick'. An alias, + `%sys_tick', exists but is deprecated and should not be used by + new software. + + * The system tick compare register is referred to as `%stick_cmpr'. + An alias, `%sys_tick_cmpr', exists but is deprecated and should + not be used by new software. + + * The software interrupt register is referred to as `%softint'. + + * The set software interrupt register is referred to as + `%set_softint'. The mnemonic `%softint_set' is provided as an + alias. + + * The clear software interrupt register is referred to as + `%clear_softint'. The mnemonic `%softint_clear' is provided as an + alias. + + * The performance instrumentation counters register is referred to as + `%pic'. + + * The performance control register is referred to as `%pcr'. + + * The graphics status register is referred to as `%gsr'. + + * The V9 dispatch control register is referred to as `%dcr'. + + Various V9 branch and conditional move instructions allow +specification of which set of integer condition codes to test. These +are referred to as `%xcc' and `%icc'. + + In V9, there are 4 sets of floating point condition codes which are +referred to as `%fccN'. + + Several special privileged and non-privileged registers exist: + + * The V9 address space identifier register is referred to as `%asi'. + + * The V9 restorable windows register is referred to as `%canrestore'. + + * The V9 savable windows register is referred to as `%cansave'. + + * The V9 clean windows register is referred to as `%cleanwin'. + + * The V9 current window pointer register is referred to as `%cwp'. + + * The floating-point queue register is referred to as `%fq'. + + * The V8 co-processor queue register is referred to as `%cq'. + + * The floating point status register is referred to as `%fsr'. + + * The other windows register is referred to as `%otherwin'. + + * The V9 program counter register is referred to as `%pc'. + + * The V9 next program counter register is referred to as `%npc'. + + * The V9 processor interrupt level register is referred to as `%pil'. + + * The V9 processor state register is referred to as `%pstate'. + + * The trap base address register is referred to as `%tba'. + + * The V9 tick register is referred to as `%tick'. + + * The V9 trap level is referred to as `%tl'. + + * The V9 trap program counter is referred to as `%tpc'. + + * The V9 trap next program counter is referred to as `%tnpc'. + + * The V9 trap state is referred to as `%tstate'. + + * The V9 trap type is referred to as `%tt'. + + * The V9 condition codes is referred to as `%ccr'. + + * The V9 floating-point registers state is referred to as `%fprs'. + + * The V9 version register is referred to as `%ver'. + + * The V9 window state register is referred to as `%wstate'. + + * The Y register is referred to as `%y'. + + * The V8 window invalid mask register is referred to as `%wim'. + + * The V8 processor state register is referred to as `%psr'. + + * The V9 global register level register is referred to as `%gl'. + + Several special register names exist for hypervisor mode code: + + * The hyperprivileged processor state register is referred to as + `%hpstate'. + + * The hyperprivileged trap state register is referred to as + `%htstate'. + + * The hyperprivileged interrupt pending register is referred to as + `%hintp'. + + * The hyperprivileged trap base address register is referred to as + `%htba'. + + * The hyperprivileged implementation version register is referred to + as `%hver'. + + * The hyperprivileged system tick compare register is referred to as + `%hstick_cmpr'. Note that there is no `%hstick' register, the + normal `%stick' is used. + + +File: as.info, Node: Sparc-Constants, Next: Sparc-Relocs, Prev: Sparc-Regs, Up: Sparc-Syntax + +9.34.3.3 Constants +.................. + +Several Sparc instructions take an immediate operand field for which +mnemonic names exist. Two such examples are `membar' and `prefetch'. +Another example are the set of V9 memory access instruction that allow +specification of an address space identifier. + + The `membar' instruction specifies a memory barrier that is the +defined by the operand which is a bitmask. The supported mask +mnemonics are: + + * `#Sync' requests that all operations (including nonmemory + reference operations) appearing prior to the `membar' must have + been performed and the effects of any exceptions become visible + before any instructions after the `membar' may be initiated. This + corresponds to `membar' cmask field bit 2. + + * `#MemIssue' requests that all memory reference operations + appearing prior to the `membar' must have been performed before + any memory operation after the `membar' may be initiated. This + corresponds to `membar' cmask field bit 1. + + * `#Lookaside' requests that a store appearing prior to the `membar' + must complete before any load following the `membar' referencing + the same address can be initiated. This corresponds to `membar' + cmask field bit 0. + + * `#StoreStore' defines that the effects of all stores appearing + prior to the `membar' instruction must be visible to all + processors before the effect of any stores following the `membar'. + Equivalent to the deprecated `stbar' instruction. This + corresponds to `membar' mmask field bit 3. + + * `#LoadStore' defines all loads appearing prior to the `membar' + instruction must have been performed before the effect of any + stores following the `membar' is visible to any other processor. + This corresponds to `membar' mmask field bit 2. + + * `#StoreLoad' defines that the effects of all stores appearing + prior to the `membar' instruction must be visible to all + processors before loads following the `membar' may be performed. + This corresponds to `membar' mmask field bit 1. + + * `#LoadLoad' defines that all loads appearing prior to the `membar' + instruction must have been performed before any loads following + the `membar' may be performed. This corresponds to `membar' mmask + field bit 0. + + + These values can be ored together, for example: + + membar #Sync + membar #StoreLoad | #LoadLoad + membar #StoreLoad | #StoreStore + + The `prefetch' and `prefetcha' instructions take a prefetch function +code. The following prefetch function code constant mnemonics are +available: + + * `#n_reads' requests a prefetch for several reads, and corresponds + to a prefetch function code of 0. + + `#one_read' requests a prefetch for one read, and corresponds to a + prefetch function code of 1. + + `#n_writes' requests a prefetch for several writes (and possibly + reads), and corresponds to a prefetch function code of 2. + + `#one_write' requests a prefetch for one write, and corresponds to + a prefetch function code of 3. + + `#page' requests a prefetch page, and corresponds to a prefetch + function code of 4. + + `#invalidate' requests a prefetch invalidate, and corresponds to a + prefetch function code of 16. + + `#unified' requests a prefetch to the nearest unified cache, and + corresponds to a prefetch function code of 17. + + `#n_reads_strong' requests a strong prefetch for several reads, + and corresponds to a prefetch function code of 20. + + `#one_read_strong' requests a strong prefetch for one read, and + corresponds to a prefetch function code of 21. + + `#n_writes_strong' requests a strong prefetch for several writes, + and corresponds to a prefetch function code of 22. + + `#one_write_strong' requests a strong prefetch for one write, and + corresponds to a prefetch function code of 23. + + Onle one prefetch code may be specified. Here are some examples: + + prefetch [%l0 + %l2], #one_read + prefetch [%g2 + 8], #n_writes + prefetcha [%g1] 0x8, #unified + prefetcha [%o0 + 0x10] %asi, #n_reads + + The actual behavior of a given prefetch function code is processor + specific. If a processor does not implement a given prefetch + function code, it will treat the prefetch instruction as a nop. + + For instructions that accept an immediate address space identifier, + `as' provides many mnemonics corresponding to V9 defined as well + as UltraSPARC and Niagara extended values. For example, `#ASI_P' + and `#ASI_BLK_INIT_QUAD_LDD_AIUS'. See the V9 and processor + specific manuals for details. + + + +File: as.info, Node: Sparc-Relocs, Next: Sparc-Size-Translations, Prev: Sparc-Constants, Up: Sparc-Syntax + +9.34.3.4 Relocations +.................... + +ELF relocations are available as defined in the 32-bit and 64-bit Sparc +ELF specifications. + + `R_SPARC_HI22' is obtained using `%hi' and `R_SPARC_LO10' is +obtained using `%lo'. Likewise `R_SPARC_HIX22' is obtained from `%hix' +and `R_SPARC_LOX10' is obtained using `%lox'. For example: + + sethi %hi(symbol), %g1 + or %g1, %lo(symbol), %g1 + + sethi %hix(symbol), %g1 + xor %g1, %lox(symbol), %g1 + + These "high" mnemonics extract bits 31:10 of their operand, and the +"low" mnemonics extract bits 9:0 of their operand. + + V9 code model relocations can be requested as follows: + + * `R_SPARC_HH22' is requested using `%hh'. It can also be generated + using `%uhi'. + + * `R_SPARC_HM10' is requested using `%hm'. It can also be generated + using `%ulo'. + + * `R_SPARC_LM22' is requested using `%lm'. + + * `R_SPARC_H44' is requested using `%h44'. + + * `R_SPARC_M44' is requested using `%m44'. + + * `R_SPARC_L44' is requested using `%l44'. + + The PC relative relocation `R_SPARC_PC22' can be obtained by +enclosing an operand inside of `%pc22'. Likewise, the `R_SPARC_PC10' +relocation can be obtained using `%pc10'. These are mostly used when +assembling PIC code. For example, the standard PIC sequence on Sparc +to get the base of the global offset table, PC relative, into a +register, can be performed as: + + sethi %pc22(_GLOBAL_OFFSET_TABLE_-4), %l7 + add %l7, %pc10(_GLOBAL_OFFSET_TABLE_+4), %l7 + + Several relocations exist to allow the link editor to potentially +optimize GOT data references. The `R_SPARC_GOTDATA_OP_HIX22' +relocation can obtained by enclosing an operand inside of +`%gdop_hix22'. The `R_SPARC_GOTDATA_OP_LOX10' relocation can obtained +by enclosing an operand inside of `%gdop_lox10'. Likewise, +`R_SPARC_GOTDATA_OP' can be obtained by enclosing an operand inside of +`%gdop'. For example, assuming the GOT base is in register `%l7': + + sethi %gdop_hix22(symbol), %l1 + xor %l1, %gdop_lox10(symbol), %l1 + ld [%l7 + %l1], %l2, %gdop(symbol) + + There are many relocations that can be requested for access to +thread local storage variables. All of the Sparc TLS mnemonics are +supported: + + * `R_SPARC_TLS_GD_HI22' is requested using `%tgd_hi22'. + + * `R_SPARC_TLS_GD_LO10' is requested using `%tgd_lo10'. + + * `R_SPARC_TLS_GD_ADD' is requested using `%tgd_add'. + + * `R_SPARC_TLS_GD_CALL' is requested using `%tgd_call'. + + * `R_SPARC_TLS_LDM_HI22' is requested using `%tldm_hi22'. + + * `R_SPARC_TLS_LDM_LO10' is requested using `%tldm_lo10'. + + * `R_SPARC_TLS_LDM_ADD' is requested using `%tldm_add'. + + * `R_SPARC_TLS_LDM_CALL' is requested using `%tldm_call'. + + * `R_SPARC_TLS_LDO_HIX22' is requested using `%tldo_hix22'. + + * `R_SPARC_TLS_LDO_LOX10' is requested using `%tldo_lox10'. + + * `R_SPARC_TLS_LDO_ADD' is requested using `%tldo_add'. + + * `R_SPARC_TLS_IE_HI22' is requested using `%tie_hi22'. + + * `R_SPARC_TLS_IE_LO10' is requested using `%tie_lo10'. + + * `R_SPARC_TLS_IE_LD' is requested using `%tie_ld'. + + * `R_SPARC_TLS_IE_LDX' is requested using `%tie_ldx'. + + * `R_SPARC_TLS_IE_ADD' is requested using `%tie_add'. + + * `R_SPARC_TLS_LE_HIX22' is requested using `%tle_hix22'. + + * `R_SPARC_TLS_LE_LOX10' is requested using `%tle_lox10'. + + Here are some example TLS model sequences. + + First, General Dynamic: + + sethi %tgd_hi22(symbol), %l1 + add %l1, %tgd_lo10(symbol), %l1 + add %l7, %l1, %o0, %tgd_add(symbol) + call __tls_get_addr, %tgd_call(symbol) + nop + + Local Dynamic: + + sethi %tldm_hi22(symbol), %l1 + add %l1, %tldm_lo10(symbol), %l1 + add %l7, %l1, %o0, %tldm_add(symbol) + call __tls_get_addr, %tldm_call(symbol) + nop + + sethi %tldo_hix22(symbol), %l1 + xor %l1, %tldo_lox10(symbol), %l1 + add %o0, %l1, %l1, %tldo_add(symbol) + + Initial Exec: + + sethi %tie_hi22(symbol), %l1 + add %l1, %tie_lo10(symbol), %l1 + ld [%l7 + %l1], %o0, %tie_ld(symbol) + add %g7, %o0, %o0, %tie_add(symbol) + + sethi %tie_hi22(symbol), %l1 + add %l1, %tie_lo10(symbol), %l1 + ldx [%l7 + %l1], %o0, %tie_ldx(symbol) + add %g7, %o0, %o0, %tie_add(symbol) + + And finally, Local Exec: + + sethi %tle_hix22(symbol), %l1 + add %l1, %tle_lox10(symbol), %l1 + add %g7, %l1, %l1 + + When assembling for 64-bit, and a secondary constant addend is +specified in an address expression that would normally generate an +`R_SPARC_LO10' relocation, the assembler will emit an `R_SPARC_OLO10' +instead. + + +File: as.info, Node: Sparc-Size-Translations, Prev: Sparc-Relocs, Up: Sparc-Syntax + +9.34.3.5 Size Translations +.......................... + +Often it is desirable to write code in an operand size agnostic manner. +`as' provides support for this via operand size opcode translations. +Translations are supported for loads, stores, shifts, compare-and-swap +atomics, and the `clr' synthetic instruction. + + If generating 32-bit code, `as' will generate the 32-bit opcode. +Whereas if 64-bit code is being generated, the 64-bit opcode will be +emitted. For example `ldn' will be transformed into `ld' for 32-bit +code and `ldx' for 64-bit code. + + Here is an example meant to demonstrate all the supported opcode +translations: + + ldn [%o0], %o1 + ldna [%o0] %asi, %o2 + stn %o1, [%o0] + stna %o2, [%o0] %asi + slln %o3, 3, %o3 + srln %o4, 8, %o4 + sran %o5, 12, %o5 + casn [%o0], %o1, %o2 + casna [%o0] %asi, %o1, %o2 + clrn %g1 + + In 32-bit mode `as' will emit: + + ld [%o0], %o1 + lda [%o0] %asi, %o2 + st %o1, [%o0] + sta %o2, [%o0] %asi + sll %o3, 3, %o3 + srl %o4, 8, %o4 + sra %o5, 12, %o5 + cas [%o0], %o1, %o2 + casa [%o0] %asi, %o1, %o2 + clr %g1 + + And in 64-bit mode `as' will emit: + + ldx [%o0], %o1 + ldxa [%o0] %asi, %o2 + stx %o1, [%o0] + stxa %o2, [%o0] %asi + sllx %o3, 3, %o3 + srlx %o4, 8, %o4 + srax %o5, 12, %o5 + casx [%o0], %o1, %o2 + casxa [%o0] %asi, %o1, %o2 + clrx %g1 + + Finally, the `.nword' translating directive is supported as well. +It is documented in the section on Sparc machine directives. + + +File: as.info, Node: Sparc-Float, Next: Sparc-Directives, Prev: Sparc-Syntax, Up: Sparc-Dependent + +9.34.4 Floating Point +--------------------- + +The Sparc uses IEEE floating-point numbers. + + +File: as.info, Node: Sparc-Directives, Prev: Sparc-Float, Up: Sparc-Dependent + +9.34.5 Sparc Machine Directives +------------------------------- + +The Sparc version of `as' supports the following additional machine +directives: + +`.align' + This must be followed by the desired alignment in bytes. + +`.common' + This must be followed by a symbol name, a positive number, and + `"bss"'. This behaves somewhat like `.comm', but the syntax is + different. + +`.half' + This is functionally identical to `.short'. + +`.nword' + On the Sparc, the `.nword' directive produces native word sized + value, ie. if assembling with -32 it is equivalent to `.word', if + assembling with -64 it is equivalent to `.xword'. + +`.proc' + This directive is ignored. Any text following it on the same line + is also ignored. + +`.register' + This directive declares use of a global application or system + register. It must be followed by a register name %g2, %g3, %g6 or + %g7, comma and the symbol name for that register. If symbol name + is `#scratch', it is a scratch register, if it is `#ignore', it + just suppresses any errors about using undeclared global register, + but does not emit any information about it into the object file. + This can be useful e.g. if you save the register before use and + restore it after. + +`.reserve' + This must be followed by a symbol name, a positive number, and + `"bss"'. This behaves somewhat like `.lcomm', but the syntax is + different. + +`.seg' + This must be followed by `"text"', `"data"', or `"data1"'. It + behaves like `.text', `.data', or `.data 1'. + +`.skip' + This is functionally identical to the `.space' directive. + +`.word' + On the Sparc, the `.word' directive produces 32 bit values, + instead of the 16 bit values it produces on many other machines. + +`.xword' + On the Sparc V9 processor, the `.xword' directive produces 64 bit + values. + + +File: as.info, Node: TIC54X-Dependent, Next: V850-Dependent, Prev: Sparc-Dependent, Up: Machine Dependencies + +9.35 TIC54X Dependent Features +============================== + +* Menu: + +* TIC54X-Opts:: Command-line Options +* TIC54X-Block:: Blocking +* TIC54X-Env:: Environment Settings +* TIC54X-Constants:: Constants Syntax +* TIC54X-Subsyms:: String Substitution +* TIC54X-Locals:: Local Label Syntax +* TIC54X-Builtins:: Builtin Assembler Math Functions +* TIC54X-Ext:: Extended Addressing Support +* TIC54X-Directives:: Directives +* TIC54X-Macros:: Macro Features +* TIC54X-MMRegs:: Memory-mapped Registers + + +File: as.info, Node: TIC54X-Opts, Next: TIC54X-Block, Up: TIC54X-Dependent + +9.35.1 Options +-------------- + +The TMS320C54X version of `as' has a few machine-dependent options. + + You can use the `-mfar-mode' option to enable extended addressing +mode. All addresses will be assumed to be > 16 bits, and the +appropriate relocation types will be used. This option is equivalent +to using the `.far_mode' directive in the assembly code. If you do not +use the `-mfar-mode' option, all references will be assumed to be 16 +bits. This option may be abbreviated to `-mf'. + + You can use the `-mcpu' option to specify a particular CPU. This +option is equivalent to using the `.version' directive in the assembly +code. For recognized CPU codes, see *Note `.version': +TIC54X-Directives. The default CPU version is `542'. + + You can use the `-merrors-to-file' option to redirect error output +to a file (this provided for those deficient environments which don't +provide adequate output redirection). This option may be abbreviated to +`-me'. + + +File: as.info, Node: TIC54X-Block, Next: TIC54X-Env, Prev: TIC54X-Opts, Up: TIC54X-Dependent + +9.35.2 Blocking +--------------- + +A blocked section or memory block is guaranteed not to cross the +blocking boundary (usually a page, or 128 words) if it is smaller than +the blocking size, or to start on a page boundary if it is larger than +the blocking size. + + +File: as.info, Node: TIC54X-Env, Next: TIC54X-Constants, Prev: TIC54X-Block, Up: TIC54X-Dependent + +9.35.3 Environment Settings +--------------------------- + +`C54XDSP_DIR' and `A_DIR' are semicolon-separated paths which are added +to the list of directories normally searched for source and include +files. `C54XDSP_DIR' will override `A_DIR'. + + +File: as.info, Node: TIC54X-Constants, Next: TIC54X-Subsyms, Prev: TIC54X-Env, Up: TIC54X-Dependent + +9.35.4 Constants Syntax +----------------------- + +The TIC54X version of `as' allows the following additional constant +formats, using a suffix to indicate the radix: + + Binary `000000B, 011000b' + Octal `10Q, 224q' + Hexadecimal `45h, 0FH' + + +File: as.info, Node: TIC54X-Subsyms, Next: TIC54X-Locals, Prev: TIC54X-Constants, Up: TIC54X-Dependent + +9.35.5 String Substitution +-------------------------- + +A subset of allowable symbols (which we'll call subsyms) may be assigned +arbitrary string values. This is roughly equivalent to C preprocessor +#define macros. When `as' encounters one of these symbols, the symbol +is replaced in the input stream by its string value. Subsym names +*must* begin with a letter. + + Subsyms may be defined using the `.asg' and `.eval' directives +(*Note `.asg': TIC54X-Directives, *Note `.eval': TIC54X-Directives. + + Expansion is recursive until a previously encountered symbol is +seen, at which point substitution stops. + + In this example, x is replaced with SYM2; SYM2 is replaced with +SYM1, and SYM1 is replaced with x. At this point, x has already been +encountered and the substitution stops. + + .asg "x",SYM1 + .asg "SYM1",SYM2 + .asg "SYM2",x + add x,a ; final code assembled is "add x, a" + + Macro parameters are converted to subsyms; a side effect of this is +the normal `as' '\ARG' dereferencing syntax is unnecessary. Subsyms +defined within a macro will have global scope, unless the `.var' +directive is used to identify the subsym as a local macro variable +*note `.var': TIC54X-Directives. + + Substitution may be forced in situations where replacement might be +ambiguous by placing colons on either side of the subsym. The following +code: + + .eval "10",x + LAB:X: add #x, a + + When assembled becomes: + + LAB10 add #10, a + + Smaller parts of the string assigned to a subsym may be accessed with +the following syntax: + +``:SYMBOL(CHAR_INDEX):'' + Evaluates to a single-character string, the character at + CHAR_INDEX. + +``:SYMBOL(START,LENGTH):'' + Evaluates to a substring of SYMBOL beginning at START with length + LENGTH. + + +File: as.info, Node: TIC54X-Locals, Next: TIC54X-Builtins, Prev: TIC54X-Subsyms, Up: TIC54X-Dependent + +9.35.6 Local Labels +------------------- + +Local labels may be defined in two ways: + + * $N, where N is a decimal number between 0 and 9 + + * LABEL?, where LABEL is any legal symbol name. + + Local labels thus defined may be redefined or automatically +generated. The scope of a local label is based on when it may be +undefined or reset. This happens when one of the following situations +is encountered: + + * .newblock directive *note `.newblock': TIC54X-Directives. + + * The current section is changed (.sect, .text, or .data) + + * Entering or leaving an included file + + * The macro scope where the label was defined is exited + + +File: as.info, Node: TIC54X-Builtins, Next: TIC54X-Ext, Prev: TIC54X-Locals, Up: TIC54X-Dependent + +9.35.7 Math Builtins +-------------------- + +The following built-in functions may be used to generate a +floating-point value. All return a floating-point value except `$cvi', +`$int', and `$sgn', which return an integer value. + +``$acos(EXPR)'' + Returns the floating point arccosine of EXPR. + +``$asin(EXPR)'' + Returns the floating point arcsine of EXPR. + +``$atan(EXPR)'' + Returns the floating point arctangent of EXPR. + +``$atan2(EXPR1,EXPR2)'' + Returns the floating point arctangent of EXPR1 / EXPR2. + +``$ceil(EXPR)'' + Returns the smallest integer not less than EXPR as floating point. + +``$cosh(EXPR)'' + Returns the floating point hyperbolic cosine of EXPR. + +``$cos(EXPR)'' + Returns the floating point cosine of EXPR. + +``$cvf(EXPR)'' + Returns the integer value EXPR converted to floating-point. + +``$cvi(EXPR)'' + Returns the floating point value EXPR converted to integer. + +``$exp(EXPR)'' + Returns the floating point value e ^ EXPR. + +``$fabs(EXPR)'' + Returns the floating point absolute value of EXPR. + +``$floor(EXPR)'' + Returns the largest integer that is not greater than EXPR as + floating point. + +``$fmod(EXPR1,EXPR2)'' + Returns the floating point remainder of EXPR1 / EXPR2. + +``$int(EXPR)'' + Returns 1 if EXPR evaluates to an integer, zero otherwise. + +``$ldexp(EXPR1,EXPR2)'' + Returns the floating point value EXPR1 * 2 ^ EXPR2. + +``$log10(EXPR)'' + Returns the base 10 logarithm of EXPR. + +``$log(EXPR)'' + Returns the natural logarithm of EXPR. + +``$max(EXPR1,EXPR2)'' + Returns the floating point maximum of EXPR1 and EXPR2. + +``$min(EXPR1,EXPR2)'' + Returns the floating point minimum of EXPR1 and EXPR2. + +``$pow(EXPR1,EXPR2)'' + Returns the floating point value EXPR1 ^ EXPR2. + +``$round(EXPR)'' + Returns the nearest integer to EXPR as a floating point number. + +``$sgn(EXPR)'' + Returns -1, 0, or 1 based on the sign of EXPR. + +``$sin(EXPR)'' + Returns the floating point sine of EXPR. + +``$sinh(EXPR)'' + Returns the floating point hyperbolic sine of EXPR. + +``$sqrt(EXPR)'' + Returns the floating point square root of EXPR. + +``$tan(EXPR)'' + Returns the floating point tangent of EXPR. + +``$tanh(EXPR)'' + Returns the floating point hyperbolic tangent of EXPR. + +``$trunc(EXPR)'' + Returns the integer value of EXPR truncated towards zero as + floating point. + + + +File: as.info, Node: TIC54X-Ext, Next: TIC54X-Directives, Prev: TIC54X-Builtins, Up: TIC54X-Dependent + +9.35.8 Extended Addressing +-------------------------- + +The `LDX' pseudo-op is provided for loading the extended addressing bits +of a label or address. For example, if an address `_label' resides in +extended program memory, the value of `_label' may be loaded as follows: + ldx #_label,16,a ; loads extended bits of _label + or #_label,a ; loads lower 16 bits of _label + bacc a ; full address is in accumulator A + + +File: as.info, Node: TIC54X-Directives, Next: TIC54X-Macros, Prev: TIC54X-Ext, Up: TIC54X-Dependent + +9.35.9 Directives +----------------- + +`.align [SIZE]' +`.even' + Align the section program counter on the next boundary, based on + SIZE. SIZE may be any power of 2. `.even' is equivalent to + `.align' with a SIZE of 2. + `1' + Align SPC to word boundary + + `2' + Align SPC to longword boundary (same as .even) + + `128' + Align SPC to page boundary + +`.asg STRING, NAME' + Assign NAME the string STRING. String replacement is performed on + STRING before assignment. + +`.eval STRING, NAME' + Evaluate the contents of string STRING and assign the result as a + string to the subsym NAME. String replacement is performed on + STRING before assignment. + +`.bss SYMBOL, SIZE [, [BLOCKING_FLAG] [,ALIGNMENT_FLAG]]' + Reserve space for SYMBOL in the .bss section. SIZE is in words. + If present, BLOCKING_FLAG indicates the allocated space should be + aligned on a page boundary if it would otherwise cross a page + boundary. If present, ALIGNMENT_FLAG causes the assembler to + allocate SIZE on a long word boundary. + +`.byte VALUE [,...,VALUE_N]' +`.ubyte VALUE [,...,VALUE_N]' +`.char VALUE [,...,VALUE_N]' +`.uchar VALUE [,...,VALUE_N]' + Place one or more bytes into consecutive words of the current + section. The upper 8 bits of each word is zero-filled. If a + label is used, it points to the word allocated for the first byte + encountered. + +`.clink ["SECTION_NAME"]' + Set STYP_CLINK flag for this section, which indicates to the + linker that if no symbols from this section are referenced, the + section should not be included in the link. If SECTION_NAME is + omitted, the current section is used. + +`.c_mode' + TBD. + +`.copy "FILENAME" | FILENAME' +`.include "FILENAME" | FILENAME' + Read source statements from FILENAME. The normal include search + path is used. Normally .copy will cause statements from the + included file to be printed in the assembly listing and .include + will not, but this distinction is not currently implemented. + +`.data' + Begin assembling code into the .data section. + +`.double VALUE [,...,VALUE_N]' +`.ldouble VALUE [,...,VALUE_N]' +`.float VALUE [,...,VALUE_N]' +`.xfloat VALUE [,...,VALUE_N]' + Place an IEEE single-precision floating-point representation of + one or more floating-point values into the current section. All + but `.xfloat' align the result on a longword boundary. Values are + stored most-significant word first. + +`.drlist' +`.drnolist' + Control printing of directives to the listing file. Ignored. + +`.emsg STRING' +`.mmsg STRING' +`.wmsg STRING' + Emit a user-defined error, message, or warning, respectively. + +`.far_mode' + Use extended addressing when assembling statements. This should + appear only once per file, and is equivalent to the -mfar-mode + option *note `-mfar-mode': TIC54X-Opts. + +`.fclist' +`.fcnolist' + Control printing of false conditional blocks to the listing file. + +`.field VALUE [,SIZE]' + Initialize a bitfield of SIZE bits in the current section. If + VALUE is relocatable, then SIZE must be 16. SIZE defaults to 16 + bits. If VALUE does not fit into SIZE bits, the value will be + truncated. Successive `.field' directives will pack starting at + the current word, filling the most significant bits first, and + aligning to the start of the next word if the field size does not + fit into the space remaining in the current word. A `.align' + directive with an operand of 1 will force the next `.field' + directive to begin packing into a new word. If a label is used, it + points to the word that contains the specified field. + +`.global SYMBOL [,...,SYMBOL_N]' +`.def SYMBOL [,...,SYMBOL_N]' +`.ref SYMBOL [,...,SYMBOL_N]' + `.def' nominally identifies a symbol defined in the current file + and available to other files. `.ref' identifies a symbol used in + the current file but defined elsewhere. Both map to the standard + `.global' directive. + +`.half VALUE [,...,VALUE_N]' +`.uhalf VALUE [,...,VALUE_N]' +`.short VALUE [,...,VALUE_N]' +`.ushort VALUE [,...,VALUE_N]' +`.int VALUE [,...,VALUE_N]' +`.uint VALUE [,...,VALUE_N]' +`.word VALUE [,...,VALUE_N]' +`.uword VALUE [,...,VALUE_N]' + Place one or more values into consecutive words of the current + section. If a label is used, it points to the word allocated for + the first value encountered. + +`.label SYMBOL' + Define a special SYMBOL to refer to the load time address of the + current section program counter. + +`.length' +`.width' + Set the page length and width of the output listing file. Ignored. + +`.list' +`.nolist' + Control whether the source listing is printed. Ignored. + +`.long VALUE [,...,VALUE_N]' +`.ulong VALUE [,...,VALUE_N]' +`.xlong VALUE [,...,VALUE_N]' + Place one or more 32-bit values into consecutive words in the + current section. The most significant word is stored first. + `.long' and `.ulong' align the result on a longword boundary; + `xlong' does not. + +`.loop [COUNT]' +`.break [CONDITION]' +`.endloop' + Repeatedly assemble a block of code. `.loop' begins the block, and + `.endloop' marks its termination. COUNT defaults to 1024, and + indicates the number of times the block should be repeated. + `.break' terminates the loop so that assembly begins after the + `.endloop' directive. The optional CONDITION will cause the loop + to terminate only if it evaluates to zero. + +`MACRO_NAME .macro [PARAM1][,...PARAM_N]' +`[.mexit]' +`.endm' + See the section on macros for more explanation (*Note + TIC54X-Macros::. + +`.mlib "FILENAME" | FILENAME' + Load the macro library FILENAME. FILENAME must be an archived + library (BFD ar-compatible) of text files, expected to contain + only macro definitions. The standard include search path is used. + +`.mlist' + +`.mnolist' + Control whether to include macro and loop block expansions in the + listing output. Ignored. + +`.mmregs' + Define global symbolic names for the 'c54x registers. Supposedly + equivalent to executing `.set' directives for each register with + its memory-mapped value, but in reality is provided only for + compatibility and does nothing. + +`.newblock' + This directive resets any TIC54X local labels currently defined. + Normal `as' local labels are unaffected. + +`.option OPTION_LIST' + Set listing options. Ignored. + +`.sblock "SECTION_NAME" | SECTION_NAME [,"NAME_N" | NAME_N]' + Designate SECTION_NAME for blocking. Blocking guarantees that a + section will start on a page boundary (128 words) if it would + otherwise cross a page boundary. Only initialized sections may be + designated with this directive. See also *Note TIC54X-Block::. + +`.sect "SECTION_NAME"' + Define a named initialized section and make it the current section. + +`SYMBOL .set "VALUE"' +`SYMBOL .equ "VALUE"' + Equate a constant VALUE to a SYMBOL, which is placed in the symbol + table. SYMBOL may not be previously defined. + +`.space SIZE_IN_BITS' +`.bes SIZE_IN_BITS' + Reserve the given number of bits in the current section and + zero-fill them. If a label is used with `.space', it points to the + *first* word reserved. With `.bes', the label points to the + *last* word reserved. + +`.sslist' +`.ssnolist' + Controls the inclusion of subsym replacement in the listing + output. Ignored. + +`.string "STRING" [,...,"STRING_N"]' +`.pstring "STRING" [,...,"STRING_N"]' + Place 8-bit characters from STRING into the current section. + `.string' zero-fills the upper 8 bits of each word, while + `.pstring' puts two characters into each word, filling the + most-significant bits first. Unused space is zero-filled. If a + label is used, it points to the first word initialized. + +`[STAG] .struct [OFFSET]' +`[NAME_1] element [COUNT_1]' +`[NAME_2] element [COUNT_2]' +`[TNAME] .tag STAGX [TCOUNT]' +`...' +`[NAME_N] element [COUNT_N]' +`[SSIZE] .endstruct' +`LABEL .tag [STAG]' + Assign symbolic offsets to the elements of a structure. STAG + defines a symbol to use to reference the structure. OFFSET + indicates a starting value to use for the first element + encountered; otherwise it defaults to zero. Each element can have + a named offset, NAME, which is a symbol assigned the value of the + element's offset into the structure. If STAG is missing, these + become global symbols. COUNT adjusts the offset that many times, + as if `element' were an array. `element' may be one of `.byte', + `.word', `.long', `.float', or any equivalent of those, and the + structure offset is adjusted accordingly. `.field' and `.string' + are also allowed; the size of `.field' is one bit, and `.string' + is considered to be one word in size. Only element descriptors, + structure/union tags, `.align' and conditional assembly directives + are allowed within `.struct'/`.endstruct'. `.align' aligns member + offsets to word boundaries only. SSIZE, if provided, will always + be assigned the size of the structure. + + The `.tag' directive, in addition to being used to define a + structure/union element within a structure, may be used to apply a + structure to a symbol. Once applied to LABEL, the individual + structure elements may be applied to LABEL to produce the desired + offsets using LABEL as the structure base. + +`.tab' + Set the tab size in the output listing. Ignored. + +`[UTAG] .union' +`[NAME_1] element [COUNT_1]' +`[NAME_2] element [COUNT_2]' +`[TNAME] .tag UTAGX[,TCOUNT]' +`...' +`[NAME_N] element [COUNT_N]' +`[USIZE] .endstruct' +`LABEL .tag [UTAG]' + Similar to `.struct', but the offset after each element is reset to + zero, and the USIZE is set to the maximum of all defined elements. + Starting offset for the union is always zero. + +`[SYMBOL] .usect "SECTION_NAME", SIZE, [,[BLOCKING_FLAG] [,ALIGNMENT_FLAG]]' + Reserve space for variables in a named, uninitialized section + (similar to .bss). `.usect' allows definitions sections + independent of .bss. SYMBOL points to the first location reserved + by this allocation. The symbol may be used as a variable name. + SIZE is the allocated size in words. BLOCKING_FLAG indicates + whether to block this section on a page boundary (128 words) + (*note TIC54X-Block::). ALIGNMENT FLAG indicates whether the + section should be longword-aligned. + +`.var SYM[,..., SYM_N]' + Define a subsym to be a local variable within a macro. See *Note + TIC54X-Macros::. + +`.version VERSION' + Set which processor to build instructions for. Though the + following values are accepted, the op is ignored. + `541' + `542' + `543' + `545' + `545LP' + `546LP' + `548' + `549' + + +File: as.info, Node: TIC54X-Macros, Next: TIC54X-MMRegs, Prev: TIC54X-Directives, Up: TIC54X-Dependent + +9.35.10 Macros +-------------- + +Macros do not require explicit dereferencing of arguments (i.e., \ARG). + + During macro expansion, the macro parameters are converted to +subsyms. If the number of arguments passed the macro invocation +exceeds the number of parameters defined, the last parameter is +assigned the string equivalent of all remaining arguments. If fewer +arguments are given than parameters, the missing parameters are +assigned empty strings. To include a comma in an argument, you must +enclose the argument in quotes. + + The following built-in subsym functions allow examination of the +string value of subsyms (or ordinary strings). The arguments are +strings unless otherwise indicated (subsyms passed as args will be +replaced by the strings they represent). +``$symlen(STR)'' + Returns the length of STR. + +``$symcmp(STR1,STR2)'' + Returns 0 if STR1 == STR2, non-zero otherwise. + +``$firstch(STR,CH)'' + Returns index of the first occurrence of character constant CH in + STR. + +``$lastch(STR,CH)'' + Returns index of the last occurrence of character constant CH in + STR. + +``$isdefed(SYMBOL)'' + Returns zero if the symbol SYMBOL is not in the symbol table, + non-zero otherwise. + +``$ismember(SYMBOL,LIST)'' + Assign the first member of comma-separated string LIST to SYMBOL; + LIST is reassigned the remainder of the list. Returns zero if + LIST is a null string. Both arguments must be subsyms. + +``$iscons(EXPR)'' + Returns 1 if string EXPR is binary, 2 if octal, 3 if hexadecimal, + 4 if a character, 5 if decimal, and zero if not an integer. + +``$isname(NAME)'' + Returns 1 if NAME is a valid symbol name, zero otherwise. + +``$isreg(REG)'' + Returns 1 if REG is a valid predefined register name (AR0-AR7 + only). + +``$structsz(STAG)'' + Returns the size of the structure or union represented by STAG. + +``$structacc(STAG)'' + Returns the reference point of the structure or union represented + by STAG. Always returns zero. + + + +File: as.info, Node: TIC54X-MMRegs, Prev: TIC54X-Macros, Up: TIC54X-Dependent + +9.35.11 Memory-mapped Registers +------------------------------- + +The following symbols are recognized as memory-mapped registers: + + + +File: as.info, Node: Z80-Dependent, Next: Z8000-Dependent, Prev: Xtensa-Dependent, Up: Machine Dependencies + +9.36 Z80 Dependent Features +=========================== + +* Menu: + +* Z80 Options:: Options +* Z80 Syntax:: Syntax +* Z80 Floating Point:: Floating Point +* Z80 Directives:: Z80 Machine Directives +* Z80 Opcodes:: Opcodes + + +File: as.info, Node: Z80 Options, Next: Z80 Syntax, Up: Z80-Dependent + +9.36.1 Options +-------------- + +The Zilog Z80 and Ascii R800 version of `as' have a few machine +dependent options. +`-z80' + Produce code for the Z80 processor. There are additional options to + request warnings and error messages for undocumented instructions. + +`-ignore-undocumented-instructions' +`-Wnud' + Silently assemble undocumented Z80-instructions that have been + adopted as documented R800-instructions. + +`-ignore-unportable-instructions' +`-Wnup' + Silently assemble all undocumented Z80-instructions. + +`-warn-undocumented-instructions' +`-Wud' + Issue warnings for undocumented Z80-instructions that work on + R800, do not assemble other undocumented instructions without + warning. + +`-warn-unportable-instructions' +`-Wup' + Issue warnings for other undocumented Z80-instructions, do not + treat any undocumented instructions as errors. + +`-forbid-undocumented-instructions' +`-Fud' + Treat all undocumented z80-instructions as errors. + +`-forbid-unportable-instructions' +`-Fup' + Treat undocumented z80-instructions that do not work on R800 as + errors. + +`-r800' + Produce code for the R800 processor. The assembler does not support + undocumented instructions for the R800. In line with common + practice, `as' uses Z80 instruction names for the R800 processor, + as far as they exist. + + +File: as.info, Node: Z80 Syntax, Next: Z80 Floating Point, Prev: Z80 Options, Up: Z80-Dependent + +9.36.2 Syntax +------------- + +The assembler syntax closely follows the 'Z80 family CPU User Manual' by +Zilog. In expressions a single `=' may be used as "is equal to" +comparison operator. + + Suffices can be used to indicate the radix of integer constants; `H' +or `h' for hexadecimal, `D' or `d' for decimal, `Q', `O', `q' or `o' +for octal, and `B' for binary. + + The suffix `b' denotes a backreference to local label. + +* Menu: + +* Z80-Chars:: Special Characters +* Z80-Regs:: Register Names +* Z80-Case:: Case Sensitivity + + +File: as.info, Node: Z80-Chars, Next: Z80-Regs, Up: Z80 Syntax + +9.36.2.1 Special Characters +........................... + +The semicolon `;' is the line comment character; + + The dollar sign `$' can be used as a prefix for hexadecimal numbers +and as a symbol denoting the current location counter. + + A backslash `\' is an ordinary character for the Z80 assembler. + + The single quote `'' must be followed by a closing quote. If there +is one character in between, it is a character constant, otherwise it is +a string constant. + + +File: as.info, Node: Z80-Regs, Next: Z80-Case, Prev: Z80-Chars, Up: Z80 Syntax + +9.36.2.2 Register Names +....................... + +The registers are referred to with the letters assigned to them by +Zilog. In addition `as' recognizes `ixl' and `ixh' as the least and +most significant octet in `ix', and similarly `iyl' and `iyh' as parts +of `iy'. + + +File: as.info, Node: Z80-Case, Prev: Z80-Regs, Up: Z80 Syntax + +9.36.2.3 Case Sensitivity +......................... + +Upper and lower case are equivalent in register names, opcodes, +condition codes and assembler directives. The case of letters is +significant in labels and symbol names. The case is also important to +distinguish the suffix `b' for a backward reference to a local label +from the suffix `B' for a number in binary notation. + + +File: as.info, Node: Z80 Floating Point, Next: Z80 Directives, Prev: Z80 Syntax, Up: Z80-Dependent + +9.36.3 Floating Point +--------------------- + +Floating-point numbers are not supported. + + +File: as.info, Node: Z80 Directives, Next: Z80 Opcodes, Prev: Z80 Floating Point, Up: Z80-Dependent + +9.36.4 Z80 Assembler Directives +------------------------------- + +`as' for the Z80 supports some additional directives for compatibility +with other assemblers. + + These are the additional directives in `as' for the Z80: + +`db EXPRESSION|STRING[,EXPRESSION|STRING...]' +`defb EXPRESSION|STRING[,EXPRESSION|STRING...]' + For each STRING the characters are copied to the object file, for + each other EXPRESSION the value is stored in one byte. A warning + is issued in case of an overflow. + +`dw EXPRESSION[,EXPRESSION...]' +`defw EXPRESSION[,EXPRESSION...]' + For each EXPRESSION the value is stored in two bytes, ignoring + overflow. + +`d24 EXPRESSION[,EXPRESSION...]' +`def24 EXPRESSION[,EXPRESSION...]' + For each EXPRESSION the value is stored in three bytes, ignoring + overflow. + +`d32 EXPRESSION[,EXPRESSION...]' +`def32 EXPRESSION[,EXPRESSION...]' + For each EXPRESSION the value is stored in four bytes, ignoring + overflow. + +`ds COUNT[, VALUE]' +`defs COUNT[, VALUE]' + Fill COUNT bytes in the object file with VALUE, if VALUE is + omitted it defaults to zero. + +`SYMBOL equ EXPRESSION' +`SYMBOL defl EXPRESSION' + These directives set the value of SYMBOL to EXPRESSION. If `equ' + is used, it is an error if SYMBOL is already defined. Symbols + defined with `equ' are not protected from redefinition. + +`set' + This is a normal instruction on Z80, and not an assembler + directive. + +`psect NAME' + A synonym for *Note Section::, no second argument should be given. + + + +File: as.info, Node: Z80 Opcodes, Prev: Z80 Directives, Up: Z80-Dependent + +9.36.5 Opcodes +-------------- + +In line with common practice, Z80 mnemonics are used for both the Z80 +and the R800. + + In many instructions it is possible to use one of the half index +registers (`ixl',`ixh',`iyl',`iyh') in stead of an 8-bit general +purpose register. This yields instructions that are documented on the +R800 and undocumented on the Z80. Similarly `in f,(c)' is documented +on the R800 and undocumented on the Z80. + + The assembler also supports the following undocumented +Z80-instructions, that have not been adopted in the R800 instruction +set: +`out (c),0' + Sends zero to the port pointed to by register c. + +`sli M' + Equivalent to `M = (M<<1)+1', the operand M can be any operand + that is valid for `sla'. One can use `sll' as a synonym for `sli'. + +`OP (ix+D), R' + This is equivalent to + + ld R, (ix+D) + OPC R + ld (ix+D), R + + The operation `OPC' may be any of `res B,', `set B,', `rl', `rlc', + `rr', `rrc', `sla', `sli', `sra' and `srl', and the register `R' + may be any of `a', `b', `c', `d', `e', `h' and `l'. + +`OPC (iy+D), R' + As above, but with `iy' instead of `ix'. + + The web site at `http://www.z80.info' is a good starting place to +find more information on programming the Z80. + + +File: as.info, Node: Z8000-Dependent, Next: Vax-Dependent, Prev: Z80-Dependent, Up: Machine Dependencies + +9.37 Z8000 Dependent Features +============================= + + The Z8000 as supports both members of the Z8000 family: the +unsegmented Z8002, with 16 bit addresses, and the segmented Z8001 with +24 bit addresses. + + When the assembler is in unsegmented mode (specified with the +`unsegm' directive), an address takes up one word (16 bit) sized +register. When the assembler is in segmented mode (specified with the +`segm' directive), a 24-bit address takes up a long (32 bit) register. +*Note Assembler Directives for the Z8000: Z8000 Directives, for a list +of other Z8000 specific assembler directives. + +* Menu: + +* Z8000 Options:: Command-line options for the Z8000 +* Z8000 Syntax:: Assembler syntax for the Z8000 +* Z8000 Directives:: Special directives for the Z8000 +* Z8000 Opcodes:: Opcodes + + +File: as.info, Node: Z8000 Options, Next: Z8000 Syntax, Up: Z8000-Dependent + +9.37.1 Options +-------------- + +`-z8001' + Generate segmented code by default. + +`-z8002' + Generate unsegmented code by default. + + +File: as.info, Node: Z8000 Syntax, Next: Z8000 Directives, Prev: Z8000 Options, Up: Z8000-Dependent + +9.37.2 Syntax +------------- + +* Menu: + +* Z8000-Chars:: Special Characters +* Z8000-Regs:: Register Names +* Z8000-Addressing:: Addressing Modes + + +File: as.info, Node: Z8000-Chars, Next: Z8000-Regs, Up: Z8000 Syntax + +9.37.2.1 Special Characters +........................... + +`!' is the line comment character. + + You can use `;' instead of a newline to separate statements. + + +File: as.info, Node: Z8000-Regs, Next: Z8000-Addressing, Prev: Z8000-Chars, Up: Z8000 Syntax + +9.37.2.2 Register Names +....................... + +The Z8000 has sixteen 16 bit registers, numbered 0 to 15. You can refer +to different sized groups of registers by register number, with the +prefix `r' for 16 bit registers, `rr' for 32 bit registers and `rq' for +64 bit registers. You can also refer to the contents of the first +eight (of the sixteen 16 bit registers) by bytes. They are named `rlN' +and `rhN'. + +_byte registers_ + rl0 rh0 rl1 rh1 rl2 rh2 rl3 rh3 + rl4 rh4 rl5 rh5 rl6 rh6 rl7 rh7 + +_word registers_ + r0 r1 r2 r3 r4 r5 r6 r7 r8 r9 r10 r11 r12 r13 r14 r15 + +_long word registers_ + rr0 rr2 rr4 rr6 rr8 rr10 rr12 rr14 + +_quad word registers_ + rq0 rq4 rq8 rq12 + + +File: as.info, Node: Z8000-Addressing, Prev: Z8000-Regs, Up: Z8000 Syntax + +9.37.2.3 Addressing Modes +......................... + +as understands the following addressing modes for the Z8000: + +`rlN' +`rhN' +`rN' +`rrN' +`rqN' + Register direct: 8bit, 16bit, 32bit, and 64bit registers. + +`@rN' +`@rrN' + Indirect register: @rrN in segmented mode, @rN in unsegmented + mode. + +`ADDR' + Direct: the 16 bit or 24 bit address (depending on whether the + assembler is in segmented or unsegmented mode) of the operand is + in the instruction. + +`address(rN)' + Indexed: the 16 or 24 bit address is added to the 16 bit register + to produce the final address in memory of the operand. + +`rN(#IMM)' +`rrN(#IMM)' + Base Address: the 16 or 24 bit register is added to the 16 bit sign + extended immediate displacement to produce the final address in + memory of the operand. + +`rN(rM)' +`rrN(rM)' + Base Index: the 16 or 24 bit register rN or rrN is added to the + sign extended 16 bit index register rM to produce the final + address in memory of the operand. + +`#XX' + Immediate data XX. + + +File: as.info, Node: Z8000 Directives, Next: Z8000 Opcodes, Prev: Z8000 Syntax, Up: Z8000-Dependent + +9.37.3 Assembler Directives for the Z8000 +----------------------------------------- + +The Z8000 port of as includes additional assembler directives, for +compatibility with other Z8000 assemblers. These do not begin with `.' +(unlike the ordinary as directives). + +`segm' +`.z8001' + Generate code for the segmented Z8001. + +`unsegm' +`.z8002' + Generate code for the unsegmented Z8002. + +`name' + Synonym for `.file' + +`global' + Synonym for `.global' + +`wval' + Synonym for `.word' + +`lval' + Synonym for `.long' + +`bval' + Synonym for `.byte' + +`sval' + Assemble a string. `sval' expects one string literal, delimited by + single quotes. It assembles each byte of the string into + consecutive addresses. You can use the escape sequence `%XX' + (where XX represents a two-digit hexadecimal number) to represent + the character whose ASCII value is XX. Use this feature to + describe single quote and other characters that may not appear in + string literals as themselves. For example, the C statement + `char *a = "he said \"it's 50% off\"";' is represented in Z8000 + assembly language (shown with the assembler output in hex at the + left) as + + 68652073 sval 'he said %22it%27s 50%25 off%22%00' + 61696420 + 22697427 + 73203530 + 25206F66 + 662200 + +`rsect' + synonym for `.section' + +`block' + synonym for `.space' + +`even' + special case of `.align'; aligns output to even byte boundary. + + +File: as.info, Node: Z8000 Opcodes, Prev: Z8000 Directives, Up: Z8000-Dependent + +9.37.4 Opcodes +-------------- + +For detailed information on the Z8000 machine instruction set, see +`Z8000 Technical Manual'. + + The following table summarizes the opcodes and their arguments: + + rs 16 bit source register + rd 16 bit destination register + rbs 8 bit source register + rbd 8 bit destination register + rrs 32 bit source register + rrd 32 bit destination register + rqs 64 bit source register + rqd 64 bit destination register + addr 16/24 bit address + imm immediate data + + adc rd,rs clrb addr cpsir @rd,@rs,rr,cc + adcb rbd,rbs clrb addr(rd) cpsirb @rd,@rs,rr,cc + add rd,@rs clrb rbd dab rbd + add rd,addr com @rd dbjnz rbd,disp7 + add rd,addr(rs) com addr dec @rd,imm4m1 + add rd,imm16 com addr(rd) dec addr(rd),imm4m1 + add rd,rs com rd dec addr,imm4m1 + addb rbd,@rs comb @rd dec rd,imm4m1 + addb rbd,addr comb addr decb @rd,imm4m1 + addb rbd,addr(rs) comb addr(rd) decb addr(rd),imm4m1 + addb rbd,imm8 comb rbd decb addr,imm4m1 + addb rbd,rbs comflg flags decb rbd,imm4m1 + addl rrd,@rs cp @rd,imm16 di i2 + addl rrd,addr cp addr(rd),imm16 div rrd,@rs + addl rrd,addr(rs) cp addr,imm16 div rrd,addr + addl rrd,imm32 cp rd,@rs div rrd,addr(rs) + addl rrd,rrs cp rd,addr div rrd,imm16 + and rd,@rs cp rd,addr(rs) div rrd,rs + and rd,addr cp rd,imm16 divl rqd,@rs + and rd,addr(rs) cp rd,rs divl rqd,addr + and rd,imm16 cpb @rd,imm8 divl rqd,addr(rs) + and rd,rs cpb addr(rd),imm8 divl rqd,imm32 + andb rbd,@rs cpb addr,imm8 divl rqd,rrs + andb rbd,addr cpb rbd,@rs djnz rd,disp7 + andb rbd,addr(rs) cpb rbd,addr ei i2 + andb rbd,imm8 cpb rbd,addr(rs) ex rd,@rs + andb rbd,rbs cpb rbd,imm8 ex rd,addr + bit @rd,imm4 cpb rbd,rbs ex rd,addr(rs) + bit addr(rd),imm4 cpd rd,@rs,rr,cc ex rd,rs + bit addr,imm4 cpdb rbd,@rs,rr,cc exb rbd,@rs + bit rd,imm4 cpdr rd,@rs,rr,cc exb rbd,addr + bit rd,rs cpdrb rbd,@rs,rr,cc exb rbd,addr(rs) + bitb @rd,imm4 cpi rd,@rs,rr,cc exb rbd,rbs + bitb addr(rd),imm4 cpib rbd,@rs,rr,cc ext0e imm8 + bitb addr,imm4 cpir rd,@rs,rr,cc ext0f imm8 + bitb rbd,imm4 cpirb rbd,@rs,rr,cc ext8e imm8 + bitb rbd,rs cpl rrd,@rs ext8f imm8 + bpt cpl rrd,addr exts rrd + call @rd cpl rrd,addr(rs) extsb rd + call addr cpl rrd,imm32 extsl rqd + call addr(rd) cpl rrd,rrs halt + calr disp12 cpsd @rd,@rs,rr,cc in rd,@rs + clr @rd cpsdb @rd,@rs,rr,cc in rd,imm16 + clr addr cpsdr @rd,@rs,rr,cc inb rbd,@rs + clr addr(rd) cpsdrb @rd,@rs,rr,cc inb rbd,imm16 + clr rd cpsi @rd,@rs,rr,cc inc @rd,imm4m1 + clrb @rd cpsib @rd,@rs,rr,cc inc addr(rd),imm4m1 + inc addr,imm4m1 ldb rbd,rs(rx) mult rrd,addr(rs) + inc rd,imm4m1 ldb rd(imm16),rbs mult rrd,imm16 + incb @rd,imm4m1 ldb rd(rx),rbs mult rrd,rs + incb addr(rd),imm4m1 ldctl ctrl,rs multl rqd,@rs + incb addr,imm4m1 ldctl rd,ctrl multl rqd,addr + incb rbd,imm4m1 ldd @rs,@rd,rr multl rqd,addr(rs) + ind @rd,@rs,ra lddb @rs,@rd,rr multl rqd,imm32 + indb @rd,@rs,rba lddr @rs,@rd,rr multl rqd,rrs + inib @rd,@rs,ra lddrb @rs,@rd,rr neg @rd + inibr @rd,@rs,ra ldi @rd,@rs,rr neg addr + iret ldib @rd,@rs,rr neg addr(rd) + jp cc,@rd ldir @rd,@rs,rr neg rd + jp cc,addr ldirb @rd,@rs,rr negb @rd + jp cc,addr(rd) ldk rd,imm4 negb addr + jr cc,disp8 ldl @rd,rrs negb addr(rd) + ld @rd,imm16 ldl addr(rd),rrs negb rbd + ld @rd,rs ldl addr,rrs nop + ld addr(rd),imm16 ldl rd(imm16),rrs or rd,@rs + ld addr(rd),rs ldl rd(rx),rrs or rd,addr + ld addr,imm16 ldl rrd,@rs or rd,addr(rs) + ld addr,rs ldl rrd,addr or rd,imm16 + ld rd(imm16),rs ldl rrd,addr(rs) or rd,rs + ld rd(rx),rs ldl rrd,imm32 orb rbd,@rs + ld rd,@rs ldl rrd,rrs orb rbd,addr + ld rd,addr ldl rrd,rs(imm16) orb rbd,addr(rs) + ld rd,addr(rs) ldl rrd,rs(rx) orb rbd,imm8 + ld rd,imm16 ldm @rd,rs,n orb rbd,rbs + ld rd,rs ldm addr(rd),rs,n out @rd,rs + ld rd,rs(imm16) ldm addr,rs,n out imm16,rs + ld rd,rs(rx) ldm rd,@rs,n outb @rd,rbs + lda rd,addr ldm rd,addr(rs),n outb imm16,rbs + lda rd,addr(rs) ldm rd,addr,n outd @rd,@rs,ra + lda rd,rs(imm16) ldps @rs outdb @rd,@rs,rba + lda rd,rs(rx) ldps addr outib @rd,@rs,ra + ldar rd,disp16 ldps addr(rs) outibr @rd,@rs,ra + ldb @rd,imm8 ldr disp16,rs pop @rd,@rs + ldb @rd,rbs ldr rd,disp16 pop addr(rd),@rs + ldb addr(rd),imm8 ldrb disp16,rbs pop addr,@rs + ldb addr(rd),rbs ldrb rbd,disp16 pop rd,@rs + ldb addr,imm8 ldrl disp16,rrs popl @rd,@rs + ldb addr,rbs ldrl rrd,disp16 popl addr(rd),@rs + ldb rbd,@rs mbit popl addr,@rs + ldb rbd,addr mreq rd popl rrd,@rs + ldb rbd,addr(rs) mres push @rd,@rs + ldb rbd,imm8 mset push @rd,addr + ldb rbd,rbs mult rrd,@rs push @rd,addr(rs) + ldb rbd,rs(imm16) mult rrd,addr push @rd,imm16 + push @rd,rs set addr,imm4 subl rrd,imm32 + pushl @rd,@rs set rd,imm4 subl rrd,rrs + pushl @rd,addr set rd,rs tcc cc,rd + pushl @rd,addr(rs) setb @rd,imm4 tccb cc,rbd + pushl @rd,rrs setb addr(rd),imm4 test @rd + res @rd,imm4 setb addr,imm4 test addr + res addr(rd),imm4 setb rbd,imm4 test addr(rd) + res addr,imm4 setb rbd,rs test rd + res rd,imm4 setflg imm4 testb @rd + res rd,rs sinb rbd,imm16 testb addr + resb @rd,imm4 sinb rd,imm16 testb addr(rd) + resb addr(rd),imm4 sind @rd,@rs,ra testb rbd + resb addr,imm4 sindb @rd,@rs,rba testl @rd + resb rbd,imm4 sinib @rd,@rs,ra testl addr + resb rbd,rs sinibr @rd,@rs,ra testl addr(rd) + resflg imm4 sla rd,imm8 testl rrd + ret cc slab rbd,imm8 trdb @rd,@rs,rba + rl rd,imm1or2 slal rrd,imm8 trdrb @rd,@rs,rba + rlb rbd,imm1or2 sll rd,imm8 trib @rd,@rs,rbr + rlc rd,imm1or2 sllb rbd,imm8 trirb @rd,@rs,rbr + rlcb rbd,imm1or2 slll rrd,imm8 trtdrb @ra,@rb,rbr + rldb rbb,rba sout imm16,rs trtib @ra,@rb,rr + rr rd,imm1or2 soutb imm16,rbs trtirb @ra,@rb,rbr + rrb rbd,imm1or2 soutd @rd,@rs,ra trtrb @ra,@rb,rbr + rrc rd,imm1or2 soutdb @rd,@rs,rba tset @rd + rrcb rbd,imm1or2 soutib @rd,@rs,ra tset addr + rrdb rbb,rba soutibr @rd,@rs,ra tset addr(rd) + rsvd36 sra rd,imm8 tset rd + rsvd38 srab rbd,imm8 tsetb @rd + rsvd78 sral rrd,imm8 tsetb addr + rsvd7e srl rd,imm8 tsetb addr(rd) + rsvd9d srlb rbd,imm8 tsetb rbd + rsvd9f srll rrd,imm8 xor rd,@rs + rsvdb9 sub rd,@rs xor rd,addr + rsvdbf sub rd,addr xor rd,addr(rs) + sbc rd,rs sub rd,addr(rs) xor rd,imm16 + sbcb rbd,rbs sub rd,imm16 xor rd,rs + sc imm8 sub rd,rs xorb rbd,@rs + sda rd,rs subb rbd,@rs xorb rbd,addr + sdab rbd,rs subb rbd,addr xorb rbd,addr(rs) + sdal rrd,rs subb rbd,addr(rs) xorb rbd,imm8 + sdl rd,rs subb rbd,imm8 xorb rbd,rbs + sdlb rbd,rs subb rbd,rbs xorb rbd,rbs + sdll rrd,rs subl rrd,@rs + set @rd,imm4 subl rrd,addr + set addr(rd),imm4 subl rrd,addr(rs) + + +File: as.info, Node: Vax-Dependent, Prev: Z8000-Dependent, Up: Machine Dependencies + +9.38 VAX Dependent Features +=========================== + +* Menu: + +* VAX-Opts:: VAX Command-Line Options +* VAX-float:: VAX Floating Point +* VAX-directives:: Vax Machine Directives +* VAX-opcodes:: VAX Opcodes +* VAX-branch:: VAX Branch Improvement +* VAX-operands:: VAX Operands +* VAX-no:: Not Supported on VAX + + +File: as.info, Node: VAX-Opts, Next: VAX-float, Up: Vax-Dependent + +9.38.1 VAX Command-Line Options +------------------------------- + +The Vax version of `as' accepts any of the following options, gives a +warning message that the option was ignored and proceeds. These +options are for compatibility with scripts designed for other people's +assemblers. + +``-D' (Debug)' +``-S' (Symbol Table)' +``-T' (Token Trace)' + These are obsolete options used to debug old assemblers. + +``-d' (Displacement size for JUMPs)' + This option expects a number following the `-d'. Like options + that expect filenames, the number may immediately follow the `-d' + (old standard) or constitute the whole of the command line + argument that follows `-d' (GNU standard). + +``-V' (Virtualize Interpass Temporary File)' + Some other assemblers use a temporary file. This option commanded + them to keep the information in active memory rather than in a + disk file. `as' always does this, so this option is redundant. + +``-J' (JUMPify Longer Branches)' + Many 32-bit computers permit a variety of branch instructions to + do the same job. Some of these instructions are short (and fast) + but have a limited range; others are long (and slow) but can + branch anywhere in virtual memory. Often there are 3 flavors of + branch: short, medium and long. Some other assemblers would emit + short and medium branches, unless told by this option to emit + short and long branches. + +``-t' (Temporary File Directory)' + Some other assemblers may use a temporary file, and this option + takes a filename being the directory to site the temporary file. + Since `as' does not use a temporary disk file, this option makes + no difference. `-t' needs exactly one filename. + + The Vax version of the assembler accepts additional options when +compiled for VMS: + +`-h N' + External symbol or section (used for global variables) names are + not case sensitive on VAX/VMS and always mapped to upper case. + This is contrary to the C language definition which explicitly + distinguishes upper and lower case. To implement a standard + conforming C compiler, names must be changed (mapped) to preserve + the case information. The default mapping is to convert all lower + case characters to uppercase and adding an underscore followed by + a 6 digit hex value, representing a 24 digit binary value. The + one digits in the binary value represent which characters are + uppercase in the original symbol name. + + The `-h N' option determines how we map names. This takes several + values. No `-h' switch at all allows case hacking as described + above. A value of zero (`-h0') implies names should be upper + case, and inhibits the case hack. A value of 2 (`-h2') implies + names should be all lower case, with no case hack. A value of 3 + (`-h3') implies that case should be preserved. The value 1 is + unused. The `-H' option directs `as' to display every mapped + symbol during assembly. + + Symbols whose names include a dollar sign `$' are exceptions to the + general name mapping. These symbols are normally only used to + reference VMS library names. Such symbols are always mapped to + upper case. + +`-+' + The `-+' option causes `as' to truncate any symbol name larger + than 31 characters. The `-+' option also prevents some code + following the `_main' symbol normally added to make the object + file compatible with Vax-11 "C". + +`-1' + This option is ignored for backward compatibility with `as' + version 1.x. + +`-H' + The `-H' option causes `as' to print every symbol which was + changed by case mapping. + + +File: as.info, Node: VAX-float, Next: VAX-directives, Prev: VAX-Opts, Up: Vax-Dependent + +9.38.2 VAX Floating Point +------------------------- + +Conversion of flonums to floating point is correct, and compatible with +previous assemblers. Rounding is towards zero if the remainder is +exactly half the least significant bit. + + `D', `F', `G' and `H' floating point formats are understood. + + Immediate floating literals (_e.g._ `S`$6.9') are rendered +correctly. Again, rounding is towards zero in the boundary case. + + The `.float' directive produces `f' format numbers. The `.double' +directive produces `d' format numbers. + + +File: as.info, Node: VAX-directives, Next: VAX-opcodes, Prev: VAX-float, Up: Vax-Dependent + +9.38.3 Vax Machine Directives +----------------------------- + +The Vax version of the assembler supports four directives for +generating Vax floating point constants. They are described in the +table below. + +`.dfloat' + This expects zero or more flonums, separated by commas, and + assembles Vax `d' format 64-bit floating point constants. + +`.ffloat' + This expects zero or more flonums, separated by commas, and + assembles Vax `f' format 32-bit floating point constants. + +`.gfloat' + This expects zero or more flonums, separated by commas, and + assembles Vax `g' format 64-bit floating point constants. + +`.hfloat' + This expects zero or more flonums, separated by commas, and + assembles Vax `h' format 128-bit floating point constants. + + + +File: as.info, Node: VAX-opcodes, Next: VAX-branch, Prev: VAX-directives, Up: Vax-Dependent + +9.38.4 VAX Opcodes +------------------ + +All DEC mnemonics are supported. Beware that `case...' instructions +have exactly 3 operands. The dispatch table that follows the `case...' +instruction should be made with `.word' statements. This is compatible +with all unix assemblers we know of. + + +File: as.info, Node: VAX-branch, Next: VAX-operands, Prev: VAX-opcodes, Up: Vax-Dependent + +9.38.5 VAX Branch Improvement +----------------------------- + +Certain pseudo opcodes are permitted. They are for branch +instructions. They expand to the shortest branch instruction that +reaches the target. Generally these mnemonics are made by substituting +`j' for `b' at the start of a DEC mnemonic. This feature is included +both for compatibility and to help compilers. If you do not need this +feature, avoid these opcodes. Here are the mnemonics, and the code +they can expand into. + +`jbsb' + `Jsb' is already an instruction mnemonic, so we chose `jbsb'. + (byte displacement) + `bsbb ...' + + (word displacement) + `bsbw ...' + + (long displacement) + `jsb ...' + +`jbr' +`jr' + Unconditional branch. + (byte displacement) + `brb ...' + + (word displacement) + `brw ...' + + (long displacement) + `jmp ...' + +`jCOND' + COND may be any one of the conditional branches `neq', `nequ', + `eql', `eqlu', `gtr', `geq', `lss', `gtru', `lequ', `vc', `vs', + `gequ', `cc', `lssu', `cs'. COND may also be one of the bit tests + `bs', `bc', `bss', `bcs', `bsc', `bcc', `bssi', `bcci', `lbs', + `lbc'. NOTCOND is the opposite condition to COND. + (byte displacement) + `bCOND ...' + + (word displacement) + `bNOTCOND foo ; brw ... ; foo:' + + (long displacement) + `bNOTCOND foo ; jmp ... ; foo:' + +`jacbX' + X may be one of `b d f g h l w'. + (word displacement) + `OPCODE ...' + + (long displacement) + OPCODE ..., foo ; + brb bar ; + foo: jmp ... ; + bar: + +`jaobYYY' + YYY may be one of `lss leq'. + +`jsobZZZ' + ZZZ may be one of `geq gtr'. + (byte displacement) + `OPCODE ...' + + (word displacement) + OPCODE ..., foo ; + brb bar ; + foo: brw DESTINATION ; + bar: + + (long displacement) + OPCODE ..., foo ; + brb bar ; + foo: jmp DESTINATION ; + bar: + +`aobleq' +`aoblss' +`sobgeq' +`sobgtr' + + (byte displacement) + `OPCODE ...' + + (word displacement) + OPCODE ..., foo ; + brb bar ; + foo: brw DESTINATION ; + bar: + + (long displacement) + OPCODE ..., foo ; + brb bar ; + foo: jmp DESTINATION ; + bar: + + +File: as.info, Node: VAX-operands, Next: VAX-no, Prev: VAX-branch, Up: Vax-Dependent + +9.38.6 VAX Operands +------------------- + +The immediate character is `$' for Unix compatibility, not `#' as DEC +writes it. + + The indirect character is `*' for Unix compatibility, not `@' as DEC +writes it. + + The displacement sizing character is ``' (an accent grave) for Unix +compatibility, not `^' as DEC writes it. The letter preceding ``' may +have either case. `G' is not understood, but all other letters (`b i l +s w') are understood. + + Register names understood are `r0 r1 r2 ... r15 ap fp sp pc'. Upper +and lower case letters are equivalent. + + For instance + tstb *w`$4(r5) + + Any expression is permitted in an operand. Operands are comma +separated. + + +File: as.info, Node: VAX-no, Prev: VAX-operands, Up: Vax-Dependent + +9.38.7 Not Supported on VAX +--------------------------- + +Vax bit fields can not be assembled with `as'. Someone can add the +required code if they really need it. + + +File: as.info, Node: V850-Dependent, Next: Xtensa-Dependent, Prev: TIC54X-Dependent, Up: Machine Dependencies + +9.39 v850 Dependent Features +============================ + +* Menu: + +* V850 Options:: Options +* V850 Syntax:: Syntax +* V850 Floating Point:: Floating Point +* V850 Directives:: V850 Machine Directives +* V850 Opcodes:: Opcodes + + +File: as.info, Node: V850 Options, Next: V850 Syntax, Up: V850-Dependent + +9.39.1 Options +-------------- + +`as' supports the following additional command-line options for the +V850 processor family: + +`-wsigned_overflow' + Causes warnings to be produced when signed immediate values + overflow the space available for then within their opcodes. By + default this option is disabled as it is possible to receive + spurious warnings due to using exact bit patterns as immediate + constants. + +`-wunsigned_overflow' + Causes warnings to be produced when unsigned immediate values + overflow the space available for then within their opcodes. By + default this option is disabled as it is possible to receive + spurious warnings due to using exact bit patterns as immediate + constants. + +`-mv850' + Specifies that the assembled code should be marked as being + targeted at the V850 processor. This allows the linker to detect + attempts to link such code with code assembled for other + processors. + +`-mv850e' + Specifies that the assembled code should be marked as being + targeted at the V850E processor. This allows the linker to detect + attempts to link such code with code assembled for other + processors. + +`-mv850e1' + Specifies that the assembled code should be marked as being + targeted at the V850E1 processor. This allows the linker to + detect attempts to link such code with code assembled for other + processors. + +`-mv850any' + Specifies that the assembled code should be marked as being + targeted at the V850 processor but support instructions that are + specific to the extended variants of the process. This allows the + production of binaries that contain target specific code, but + which are also intended to be used in a generic fashion. For + example libgcc.a contains generic routines used by the code + produced by GCC for all versions of the v850 architecture, + together with support routines only used by the V850E architecture. + +`-mrelax' + Enables relaxation. This allows the .longcall and .longjump pseudo + ops to be used in the assembler source code. These ops label + sections of code which are either a long function call or a long + branch. The assembler will then flag these sections of code and + the linker will attempt to relax them. + + + +File: as.info, Node: V850 Syntax, Next: V850 Floating Point, Prev: V850 Options, Up: V850-Dependent + +9.39.2 Syntax +------------- + +* Menu: + +* V850-Chars:: Special Characters +* V850-Regs:: Register Names + + +File: as.info, Node: V850-Chars, Next: V850-Regs, Up: V850 Syntax + +9.39.2.1 Special Characters +........................... + +`#' is the line comment character. + + +File: as.info, Node: V850-Regs, Prev: V850-Chars, Up: V850 Syntax + +9.39.2.2 Register Names +....................... + +`as' supports the following names for registers: +`general register 0' + r0, zero + +`general register 1' + r1 + +`general register 2' + r2, hp + +`general register 3' + r3, sp + +`general register 4' + r4, gp + +`general register 5' + r5, tp + +`general register 6' + r6 + +`general register 7' + r7 + +`general register 8' + r8 + +`general register 9' + r9 + +`general register 10' + r10 + +`general register 11' + r11 + +`general register 12' + r12 + +`general register 13' + r13 + +`general register 14' + r14 + +`general register 15' + r15 + +`general register 16' + r16 + +`general register 17' + r17 + +`general register 18' + r18 + +`general register 19' + r19 + +`general register 20' + r20 + +`general register 21' + r21 + +`general register 22' + r22 + +`general register 23' + r23 + +`general register 24' + r24 + +`general register 25' + r25 + +`general register 26' + r26 + +`general register 27' + r27 + +`general register 28' + r28 + +`general register 29' + r29 + +`general register 30' + r30, ep + +`general register 31' + r31, lp + +`system register 0' + eipc + +`system register 1' + eipsw + +`system register 2' + fepc + +`system register 3' + fepsw + +`system register 4' + ecr + +`system register 5' + psw + +`system register 16' + ctpc + +`system register 17' + ctpsw + +`system register 18' + dbpc + +`system register 19' + dbpsw + +`system register 20' + ctbp + + +File: as.info, Node: V850 Floating Point, Next: V850 Directives, Prev: V850 Syntax, Up: V850-Dependent + +9.39.3 Floating Point +--------------------- + +The V850 family uses IEEE floating-point numbers. + + +File: as.info, Node: V850 Directives, Next: V850 Opcodes, Prev: V850 Floating Point, Up: V850-Dependent + +9.39.4 V850 Machine Directives +------------------------------ + +`.offset <EXPRESSION>' + Moves the offset into the current section to the specified amount. + +`.section "name", <type>' + This is an extension to the standard .section directive. It sets + the current section to be <type> and creates an alias for this + section called "name". + +`.v850' + Specifies that the assembled code should be marked as being + targeted at the V850 processor. This allows the linker to detect + attempts to link such code with code assembled for other + processors. + +`.v850e' + Specifies that the assembled code should be marked as being + targeted at the V850E processor. This allows the linker to detect + attempts to link such code with code assembled for other + processors. + +`.v850e1' + Specifies that the assembled code should be marked as being + targeted at the V850E1 processor. This allows the linker to + detect attempts to link such code with code assembled for other + processors. + + + +File: as.info, Node: V850 Opcodes, Prev: V850 Directives, Up: V850-Dependent + +9.39.5 Opcodes +-------------- + +`as' implements all the standard V850 opcodes. + + `as' also implements the following pseudo ops: + +`hi0()' + Computes the higher 16 bits of the given expression and stores it + into the immediate operand field of the given instruction. For + example: + + `mulhi hi0(here - there), r5, r6' + + computes the difference between the address of labels 'here' and + 'there', takes the upper 16 bits of this difference, shifts it + down 16 bits and then multiplies it by the lower 16 bits in + register 5, putting the result into register 6. + +`lo()' + Computes the lower 16 bits of the given expression and stores it + into the immediate operand field of the given instruction. For + example: + + `addi lo(here - there), r5, r6' + + computes the difference between the address of labels 'here' and + 'there', takes the lower 16 bits of this difference and adds it to + register 5, putting the result into register 6. + +`hi()' + Computes the higher 16 bits of the given expression and then adds + the value of the most significant bit of the lower 16 bits of the + expression and stores the result into the immediate operand field + of the given instruction. For example the following code can be + used to compute the address of the label 'here' and store it into + register 6: + + `movhi hi(here), r0, r6' `movea lo(here), r6, r6' + + The reason for this special behaviour is that movea performs a sign + extension on its immediate operand. So for example if the address + of 'here' was 0xFFFFFFFF then without the special behaviour of the + hi() pseudo-op the movhi instruction would put 0xFFFF0000 into r6, + then the movea instruction would takes its immediate operand, + 0xFFFF, sign extend it to 32 bits, 0xFFFFFFFF, and then add it + into r6 giving 0xFFFEFFFF which is wrong (the fifth nibble is E). + With the hi() pseudo op adding in the top bit of the lo() pseudo + op, the movhi instruction actually stores 0 into r6 (0xFFFF + 1 = + 0x0000), so that the movea instruction stores 0xFFFFFFFF into r6 - + the right value. + +`hilo()' + Computes the 32 bit value of the given expression and stores it + into the immediate operand field of the given instruction (which + must be a mov instruction). For example: + + `mov hilo(here), r6' + + computes the absolute address of label 'here' and puts the result + into register 6. + +`sdaoff()' + Computes the offset of the named variable from the start of the + Small Data Area (whoes address is held in register 4, the GP + register) and stores the result as a 16 bit signed value in the + immediate operand field of the given instruction. For example: + + `ld.w sdaoff(_a_variable)[gp],r6' + + loads the contents of the location pointed to by the label + '_a_variable' into register 6, provided that the label is located + somewhere within +/- 32K of the address held in the GP register. + [Note the linker assumes that the GP register contains a fixed + address set to the address of the label called '__gp'. This can + either be set up automatically by the linker, or specifically set + by using the `--defsym __gp=<value>' command line option]. + +`tdaoff()' + Computes the offset of the named variable from the start of the + Tiny Data Area (whoes address is held in register 30, the EP + register) and stores the result as a 4,5, 7 or 8 bit unsigned + value in the immediate operand field of the given instruction. + For example: + + `sld.w tdaoff(_a_variable)[ep],r6' + + loads the contents of the location pointed to by the label + '_a_variable' into register 6, provided that the label is located + somewhere within +256 bytes of the address held in the EP + register. [Note the linker assumes that the EP register contains + a fixed address set to the address of the label called '__ep'. + This can either be set up automatically by the linker, or + specifically set by using the `--defsym __ep=<value>' command line + option]. + +`zdaoff()' + Computes the offset of the named variable from address 0 and + stores the result as a 16 bit signed value in the immediate + operand field of the given instruction. For example: + + `movea zdaoff(_a_variable),zero,r6' + + puts the address of the label '_a_variable' into register 6, + assuming that the label is somewhere within the first 32K of + memory. (Strictly speaking it also possible to access the last + 32K of memory as well, as the offsets are signed). + +`ctoff()' + Computes the offset of the named variable from the start of the + Call Table Area (whoes address is helg in system register 20, the + CTBP register) and stores the result a 6 or 16 bit unsigned value + in the immediate field of then given instruction or piece of data. + For example: + + `callt ctoff(table_func1)' + + will put the call the function whoes address is held in the call + table at the location labeled 'table_func1'. + +`.longcall `name'' + Indicates that the following sequence of instructions is a long + call to function `name'. The linker will attempt to shorten this + call sequence if `name' is within a 22bit offset of the call. Only + valid if the `-mrelax' command line switch has been enabled. + +`.longjump `name'' + Indicates that the following sequence of instructions is a long + jump to label `name'. The linker will attempt to shorten this code + sequence if `name' is within a 22bit offset of the jump. Only + valid if the `-mrelax' command line switch has been enabled. + + + For information on the V850 instruction set, see `V850 Family +32-/16-Bit single-Chip Microcontroller Architecture Manual' from NEC. +Ltd. + + +File: as.info, Node: Xtensa-Dependent, Next: Z80-Dependent, Prev: V850-Dependent, Up: Machine Dependencies + +9.40 Xtensa Dependent Features +============================== + + This chapter covers features of the GNU assembler that are specific +to the Xtensa architecture. For details about the Xtensa instruction +set, please consult the `Xtensa Instruction Set Architecture (ISA) +Reference Manual'. + +* Menu: + +* Xtensa Options:: Command-line Options. +* Xtensa Syntax:: Assembler Syntax for Xtensa Processors. +* Xtensa Optimizations:: Assembler Optimizations. +* Xtensa Relaxation:: Other Automatic Transformations. +* Xtensa Directives:: Directives for Xtensa Processors. + + +File: as.info, Node: Xtensa Options, Next: Xtensa Syntax, Up: Xtensa-Dependent + +9.40.1 Command Line Options +--------------------------- + +The Xtensa version of the GNU assembler supports these special options: + +`--text-section-literals | --no-text-section-literals' + Control the treatment of literal pools. The default is + `--no-text-section-literals', which places literals in separate + sections in the output file. This allows the literal pool to be + placed in a data RAM/ROM. With `--text-section-literals', the + literals are interspersed in the text section in order to keep + them as close as possible to their references. This may be + necessary for large assembly files, where the literals would + otherwise be out of range of the `L32R' instructions in the text + section. These options only affect literals referenced via + PC-relative `L32R' instructions; literals for absolute mode `L32R' + instructions are handled separately. *Note literal: Literal + Directive. + +`--absolute-literals | --no-absolute-literals' + Indicate to the assembler whether `L32R' instructions use absolute + or PC-relative addressing. If the processor includes the absolute + addressing option, the default is to use absolute `L32R' + relocations. Otherwise, only the PC-relative `L32R' relocations + can be used. + +`--target-align | --no-target-align' + Enable or disable automatic alignment to reduce branch penalties + at some expense in code size. *Note Automatic Instruction + Alignment: Xtensa Automatic Alignment. This optimization is + enabled by default. Note that the assembler will always align + instructions like `LOOP' that have fixed alignment requirements. + +`--longcalls | --no-longcalls' + Enable or disable transformation of call instructions to allow + calls across a greater range of addresses. *Note Function Call + Relaxation: Xtensa Call Relaxation. This option should be used + when call targets can potentially be out of range. It may degrade + both code size and performance, but the linker can generally + optimize away the unnecessary overhead when a call ends up within + range. The default is `--no-longcalls'. + +`--transform | --no-transform' + Enable or disable all assembler transformations of Xtensa + instructions, including both relaxation and optimization. The + default is `--transform'; `--no-transform' should only be used in + the rare cases when the instructions must be exactly as specified + in the assembly source. Using `--no-transform' causes out of range + instruction operands to be errors. + +`--rename-section OLDNAME=NEWNAME' + Rename the OLDNAME section to NEWNAME. This option can be used + multiple times to rename multiple sections. + + +File: as.info, Node: Xtensa Syntax, Next: Xtensa Optimizations, Prev: Xtensa Options, Up: Xtensa-Dependent + +9.40.2 Assembler Syntax +----------------------- + +Block comments are delimited by `/*' and `*/'. End of line comments +may be introduced with either `#' or `//'. + + Instructions consist of a leading opcode or macro name followed by +whitespace and an optional comma-separated list of operands: + + OPCODE [OPERAND, ...] + + Instructions must be separated by a newline or semicolon. + + FLIX instructions, which bundle multiple opcodes together in a single +instruction, are specified by enclosing the bundled opcodes inside +braces: + + { + [FORMAT] + OPCODE0 [OPERANDS] + OPCODE1 [OPERANDS] + OPCODE2 [OPERANDS] + ... + } + + The opcodes in a FLIX instruction are listed in the same order as the +corresponding instruction slots in the TIE format declaration. +Directives and labels are not allowed inside the braces of a FLIX +instruction. A particular TIE format name can optionally be specified +immediately after the opening brace, but this is usually unnecessary. +The assembler will automatically search for a format that can encode the +specified opcodes, so the format name need only be specified in rare +cases where there is more than one applicable format and where it +matters which of those formats is used. A FLIX instruction can also be +specified on a single line by separating the opcodes with semicolons: + + { [FORMAT;] OPCODE0 [OPERANDS]; OPCODE1 [OPERANDS]; OPCODE2 [OPERANDS]; ... } + + If an opcode can only be encoded in a FLIX instruction but is not +specified as part of a FLIX bundle, the assembler will choose the +smallest format where the opcode can be encoded and will fill unused +instruction slots with no-ops. + +* Menu: + +* Xtensa Opcodes:: Opcode Naming Conventions. +* Xtensa Registers:: Register Naming. + + +File: as.info, Node: Xtensa Opcodes, Next: Xtensa Registers, Up: Xtensa Syntax + +9.40.2.1 Opcode Names +..................... + +See the `Xtensa Instruction Set Architecture (ISA) Reference Manual' +for a complete list of opcodes and descriptions of their semantics. + + If an opcode name is prefixed with an underscore character (`_'), +`as' will not transform that instruction in any way. The underscore +prefix disables both optimization (*note Xtensa Optimizations: Xtensa +Optimizations.) and relaxation (*note Xtensa Relaxation: Xtensa +Relaxation.) for that particular instruction. Only use the underscore +prefix when it is essential to select the exact opcode produced by the +assembler. Using this feature unnecessarily makes the code less +efficient by disabling assembler optimization and less flexible by +disabling relaxation. + + Note that this special handling of underscore prefixes only applies +to Xtensa opcodes, not to either built-in macros or user-defined macros. +When an underscore prefix is used with a macro (e.g., `_MOV'), it +refers to a different macro. The assembler generally provides built-in +macros both with and without the underscore prefix, where the underscore +versions behave as if the underscore carries through to the instructions +in the macros. For example, `_MOV' may expand to `_MOV.N'. + + The underscore prefix only applies to individual instructions, not to +series of instructions. For example, if a series of instructions have +underscore prefixes, the assembler will not transform the individual +instructions, but it may insert other instructions between them (e.g., +to align a `LOOP' instruction). To prevent the assembler from +modifying a series of instructions as a whole, use the `no-transform' +directive. *Note transform: Transform Directive. + + +File: as.info, Node: Xtensa Registers, Prev: Xtensa Opcodes, Up: Xtensa Syntax + +9.40.2.2 Register Names +....................... + +The assembly syntax for a register file entry is the "short" name for a +TIE register file followed by the index into that register file. For +example, the general-purpose `AR' register file has a short name of +`a', so these registers are named `a0'...`a15'. As a special feature, +`sp' is also supported as a synonym for `a1'. Additional registers may +be added by processor configuration options and by designer-defined TIE +extensions. An initial `$' character is optional in all register names. + + +File: as.info, Node: Xtensa Optimizations, Next: Xtensa Relaxation, Prev: Xtensa Syntax, Up: Xtensa-Dependent + +9.40.3 Xtensa Optimizations +--------------------------- + +The optimizations currently supported by `as' are generation of density +instructions where appropriate and automatic branch target alignment. + +* Menu: + +* Density Instructions:: Using Density Instructions. +* Xtensa Automatic Alignment:: Automatic Instruction Alignment. + + +File: as.info, Node: Density Instructions, Next: Xtensa Automatic Alignment, Up: Xtensa Optimizations + +9.40.3.1 Using Density Instructions +................................... + +The Xtensa instruction set has a code density option that provides +16-bit versions of some of the most commonly used opcodes. Use of these +opcodes can significantly reduce code size. When possible, the +assembler automatically translates instructions from the core Xtensa +instruction set into equivalent instructions from the Xtensa code +density option. This translation can be disabled by using underscore +prefixes (*note Opcode Names: Xtensa Opcodes.), by using the +`--no-transform' command-line option (*note Command Line Options: +Xtensa Options.), or by using the `no-transform' directive (*note +transform: Transform Directive.). + + It is a good idea _not_ to use the density instructions directly. +The assembler will automatically select dense instructions where +possible. If you later need to use an Xtensa processor without the code +density option, the same assembly code will then work without +modification. + + +File: as.info, Node: Xtensa Automatic Alignment, Prev: Density Instructions, Up: Xtensa Optimizations + +9.40.3.2 Automatic Instruction Alignment +........................................ + +The Xtensa assembler will automatically align certain instructions, both +to optimize performance and to satisfy architectural requirements. + + As an optimization to improve performance, the assembler attempts to +align branch targets so they do not cross instruction fetch boundaries. +(Xtensa processors can be configured with either 32-bit or 64-bit +instruction fetch widths.) An instruction immediately following a call +is treated as a branch target in this context, because it will be the +target of a return from the call. This alignment has the potential to +reduce branch penalties at some expense in code size. This +optimization is enabled by default. You can disable it with the +`--no-target-align' command-line option (*note Command Line Options: +Xtensa Options.). + + The target alignment optimization is done without adding instructions +that could increase the execution time of the program. If there are +density instructions in the code preceding a target, the assembler can +change the target alignment by widening some of those instructions to +the equivalent 24-bit instructions. Extra bytes of padding can be +inserted immediately following unconditional jump and return +instructions. This approach is usually successful in aligning many, +but not all, branch targets. + + The `LOOP' family of instructions must be aligned such that the +first instruction in the loop body does not cross an instruction fetch +boundary (e.g., with a 32-bit fetch width, a `LOOP' instruction must be +on either a 1 or 2 mod 4 byte boundary). The assembler knows about +this restriction and inserts the minimal number of 2 or 3 byte no-op +instructions to satisfy it. When no-op instructions are added, any +label immediately preceding the original loop will be moved in order to +refer to the loop instruction, not the newly generated no-op +instruction. To preserve binary compatibility across processors with +different fetch widths, the assembler conservatively assumes a 32-bit +fetch width when aligning `LOOP' instructions (except if the first +instruction in the loop is a 64-bit instruction). + + Previous versions of the assembler automatically aligned `ENTRY' +instructions to 4-byte boundaries, but that alignment is now the +programmer's responsibility. + + +File: as.info, Node: Xtensa Relaxation, Next: Xtensa Directives, Prev: Xtensa Optimizations, Up: Xtensa-Dependent + +9.40.4 Xtensa Relaxation +------------------------ + +When an instruction operand is outside the range allowed for that +particular instruction field, `as' can transform the code to use a +functionally-equivalent instruction or sequence of instructions. This +process is known as "relaxation". This is typically done for branch +instructions because the distance of the branch targets is not known +until assembly-time. The Xtensa assembler offers branch relaxation and +also extends this concept to function calls, `MOVI' instructions and +other instructions with immediate fields. + +* Menu: + +* Xtensa Branch Relaxation:: Relaxation of Branches. +* Xtensa Call Relaxation:: Relaxation of Function Calls. +* Xtensa Immediate Relaxation:: Relaxation of other Immediate Fields. + + +File: as.info, Node: Xtensa Branch Relaxation, Next: Xtensa Call Relaxation, Up: Xtensa Relaxation + +9.40.4.1 Conditional Branch Relaxation +...................................... + +When the target of a branch is too far away from the branch itself, +i.e., when the offset from the branch to the target is too large to fit +in the immediate field of the branch instruction, it may be necessary to +replace the branch with a branch around a jump. For example, + + beqz a2, L + + may result in: + + bnez.n a2, M + j L + M: + + (The `BNEZ.N' instruction would be used in this example only if the +density option is available. Otherwise, `BNEZ' would be used.) + + This relaxation works well because the unconditional jump instruction +has a much larger offset range than the various conditional branches. +However, an error will occur if a branch target is beyond the range of a +jump instruction. `as' cannot relax unconditional jumps. Similarly, +an error will occur if the original input contains an unconditional +jump to a target that is out of range. + + Branch relaxation is enabled by default. It can be disabled by using +underscore prefixes (*note Opcode Names: Xtensa Opcodes.), the +`--no-transform' command-line option (*note Command Line Options: +Xtensa Options.), or the `no-transform' directive (*note transform: +Transform Directive.). + + +File: as.info, Node: Xtensa Call Relaxation, Next: Xtensa Immediate Relaxation, Prev: Xtensa Branch Relaxation, Up: Xtensa Relaxation + +9.40.4.2 Function Call Relaxation +................................. + +Function calls may require relaxation because the Xtensa immediate call +instructions (`CALL0', `CALL4', `CALL8' and `CALL12') provide a +PC-relative offset of only 512 Kbytes in either direction. For larger +programs, it may be necessary to use indirect calls (`CALLX0', +`CALLX4', `CALLX8' and `CALLX12') where the target address is specified +in a register. The Xtensa assembler can automatically relax immediate +call instructions into indirect call instructions. This relaxation is +done by loading the address of the called function into the callee's +return address register and then using a `CALLX' instruction. So, for +example: + + call8 func + + might be relaxed to: + + .literal .L1, func + l32r a8, .L1 + callx8 a8 + + Because the addresses of targets of function calls are not generally +known until link-time, the assembler must assume the worst and relax all +the calls to functions in other source files, not just those that really +will be out of range. The linker can recognize calls that were +unnecessarily relaxed, and it will remove the overhead introduced by the +assembler for those cases where direct calls are sufficient. + + Call relaxation is disabled by default because it can have a negative +effect on both code size and performance, although the linker can +usually eliminate the unnecessary overhead. If a program is too large +and some of the calls are out of range, function call relaxation can be +enabled using the `--longcalls' command-line option or the `longcalls' +directive (*note longcalls: Longcalls Directive.). + + +File: as.info, Node: Xtensa Immediate Relaxation, Prev: Xtensa Call Relaxation, Up: Xtensa Relaxation + +9.40.4.3 Other Immediate Field Relaxation +......................................... + +The assembler normally performs the following other relaxations. They +can be disabled by using underscore prefixes (*note Opcode Names: +Xtensa Opcodes.), the `--no-transform' command-line option (*note +Command Line Options: Xtensa Options.), or the `no-transform' directive +(*note transform: Transform Directive.). + + The `MOVI' machine instruction can only materialize values in the +range from -2048 to 2047. Values outside this range are best +materialized with `L32R' instructions. Thus: + + movi a0, 100000 + + is assembled into the following machine code: + + .literal .L1, 100000 + l32r a0, .L1 + + The `L8UI' machine instruction can only be used with immediate +offsets in the range from 0 to 255. The `L16SI' and `L16UI' machine +instructions can only be used with offsets from 0 to 510. The `L32I' +machine instruction can only be used with offsets from 0 to 1020. A +load offset outside these ranges can be materialized with an `L32R' +instruction if the destination register of the load is different than +the source address register. For example: + + l32i a1, a0, 2040 + + is translated to: + + .literal .L1, 2040 + l32r a1, .L1 + add a1, a0, a1 + l32i a1, a1, 0 + +If the load destination and source address register are the same, an +out-of-range offset causes an error. + + The Xtensa `ADDI' instruction only allows immediate operands in the +range from -128 to 127. There are a number of alternate instruction +sequences for the `ADDI' operation. First, if the immediate is 0, the +`ADDI' will be turned into a `MOV.N' instruction (or the equivalent +`OR' instruction if the code density option is not available). If the +`ADDI' immediate is outside of the range -128 to 127, but inside the +range -32896 to 32639, an `ADDMI' instruction or `ADDMI'/`ADDI' +sequence will be used. Finally, if the immediate is outside of this +range and a free register is available, an `L32R'/`ADD' sequence will +be used with a literal allocated from the literal pool. + + For example: + + addi a5, a6, 0 + addi a5, a6, 512 + addi a5, a6, 513 + addi a5, a6, 50000 + + is assembled into the following: + + .literal .L1, 50000 + mov.n a5, a6 + addmi a5, a6, 0x200 + addmi a5, a6, 0x200 + addi a5, a5, 1 + l32r a5, .L1 + add a5, a6, a5 + + +File: as.info, Node: Xtensa Directives, Prev: Xtensa Relaxation, Up: Xtensa-Dependent + +9.40.5 Directives +----------------- + +The Xtensa assembler supports a region-based directive syntax: + + .begin DIRECTIVE [OPTIONS] + ... + .end DIRECTIVE + + All the Xtensa-specific directives that apply to a region of code use +this syntax. + + The directive applies to code between the `.begin' and the `.end'. +The state of the option after the `.end' reverts to what it was before +the `.begin'. A nested `.begin'/`.end' region can further change the +state of the directive without having to be aware of its outer state. +For example, consider: + + .begin no-transform + L: add a0, a1, a2 + .begin transform + M: add a0, a1, a2 + .end transform + N: add a0, a1, a2 + .end no-transform + + The `ADD' opcodes at `L' and `N' in the outer `no-transform' region +both result in `ADD' machine instructions, but the assembler selects an +`ADD.N' instruction for the `ADD' at `M' in the inner `transform' +region. + + The advantage of this style is that it works well inside macros +which can preserve the context of their callers. + + The following directives are available: + +* Menu: + +* Schedule Directive:: Enable instruction scheduling. +* Longcalls Directive:: Use Indirect Calls for Greater Range. +* Transform Directive:: Disable All Assembler Transformations. +* Literal Directive:: Intermix Literals with Instructions. +* Literal Position Directive:: Specify Inline Literal Pool Locations. +* Literal Prefix Directive:: Specify Literal Section Name Prefix. +* Absolute Literals Directive:: Control PC-Relative vs. Absolute Literals. + + +File: as.info, Node: Schedule Directive, Next: Longcalls Directive, Up: Xtensa Directives + +9.40.5.1 schedule +................. + +The `schedule' directive is recognized only for compatibility with +Tensilica's assembler. + + .begin [no-]schedule + .end [no-]schedule + + This directive is ignored and has no effect on `as'. + + +File: as.info, Node: Longcalls Directive, Next: Transform Directive, Prev: Schedule Directive, Up: Xtensa Directives + +9.40.5.2 longcalls +.................. + +The `longcalls' directive enables or disables function call relaxation. +*Note Function Call Relaxation: Xtensa Call Relaxation. + + .begin [no-]longcalls + .end [no-]longcalls + + Call relaxation is disabled by default unless the `--longcalls' +command-line option is specified. The `longcalls' directive overrides +the default determined by the command-line options. + + +File: as.info, Node: Transform Directive, Next: Literal Directive, Prev: Longcalls Directive, Up: Xtensa Directives + +9.40.5.3 transform +.................. + +This directive enables or disables all assembler transformation, +including relaxation (*note Xtensa Relaxation: Xtensa Relaxation.) and +optimization (*note Xtensa Optimizations: Xtensa Optimizations.). + + .begin [no-]transform + .end [no-]transform + + Transformations are enabled by default unless the `--no-transform' +option is used. The `transform' directive overrides the default +determined by the command-line options. An underscore opcode prefix, +disabling transformation of that opcode, always takes precedence over +both directives and command-line flags. + + +File: as.info, Node: Literal Directive, Next: Literal Position Directive, Prev: Transform Directive, Up: Xtensa Directives + +9.40.5.4 literal +................ + +The `.literal' directive is used to define literal pool data, i.e., +read-only 32-bit data accessed via `L32R' instructions. + + .literal LABEL, VALUE[, VALUE...] + + This directive is similar to the standard `.word' directive, except +that the actual location of the literal data is determined by the +assembler and linker, not by the position of the `.literal' directive. +Using this directive gives the assembler freedom to locate the literal +data in the most appropriate place and possibly to combine identical +literals. For example, the code: + + entry sp, 40 + .literal .L1, sym + l32r a4, .L1 + + can be used to load a pointer to the symbol `sym' into register +`a4'. The value of `sym' will not be placed between the `ENTRY' and +`L32R' instructions; instead, the assembler puts the data in a literal +pool. + + Literal pools are placed by default in separate literal sections; +however, when using the `--text-section-literals' option (*note Command +Line Options: Xtensa Options.), the literal pools for PC-relative mode +`L32R' instructions are placed in the current section.(1) These text +section literal pools are created automatically before `ENTRY' +instructions and manually after `.literal_position' directives (*note +literal_position: Literal Position Directive.). If there are no +preceding `ENTRY' instructions, explicit `.literal_position' directives +must be used to place the text section literal pools; otherwise, `as' +will report an error. + + When literals are placed in separate sections, the literal section +names are derived from the names of the sections where the literals are +defined. The base literal section names are `.literal' for PC-relative +mode `L32R' instructions and `.lit4' for absolute mode `L32R' +instructions (*note absolute-literals: Absolute Literals Directive.). +These base names are used for literals defined in the default `.text' +section. For literals defined in other sections or within the scope of +a `literal_prefix' directive (*note literal_prefix: Literal Prefix +Directive.), the following rules determine the literal section name: + + 1. If the current section is a member of a section group, the literal + section name includes the group name as a suffix to the base + `.literal' or `.lit4' name, with a period to separate the base + name and group name. The literal section is also made a member of + the group. + + 2. If the current section name (or `literal_prefix' value) begins with + "`.gnu.linkonce.KIND.'", the literal section name is formed by + replacing "`.KIND'" with the base `.literal' or `.lit4' name. For + example, for literals defined in a section named + `.gnu.linkonce.t.func', the literal section will be + `.gnu.linkonce.literal.func' or `.gnu.linkonce.lit4.func'. + + 3. If the current section name (or `literal_prefix' value) ends with + `.text', the literal section name is formed by replacing that + suffix with the base `.literal' or `.lit4' name. For example, for + literals defined in a section named `.iram0.text', the literal + section will be `.iram0.literal' or `.iram0.lit4'. + + 4. If none of the preceding conditions apply, the literal section + name is formed by adding the base `.literal' or `.lit4' name as a + suffix to the current section name (or `literal_prefix' value). + + ---------- Footnotes ---------- + + (1) Literals for the `.init' and `.fini' sections are always placed +in separate sections, even when `--text-section-literals' is enabled. + + +File: as.info, Node: Literal Position Directive, Next: Literal Prefix Directive, Prev: Literal Directive, Up: Xtensa Directives + +9.40.5.5 literal_position +......................... + +When using `--text-section-literals' to place literals inline in the +section being assembled, the `.literal_position' directive can be used +to mark a potential location for a literal pool. + + .literal_position + + The `.literal_position' directive is ignored when the +`--text-section-literals' option is not used or when `L32R' +instructions use the absolute addressing mode. + + The assembler will automatically place text section literal pools +before `ENTRY' instructions, so the `.literal_position' directive is +only needed to specify some other location for a literal pool. You may +need to add an explicit jump instruction to skip over an inline literal +pool. + + For example, an interrupt vector does not begin with an `ENTRY' +instruction so the assembler will be unable to automatically find a good +place to put a literal pool. Moreover, the code for the interrupt +vector must be at a specific starting address, so the literal pool +cannot come before the start of the code. The literal pool for the +vector must be explicitly positioned in the middle of the vector (before +any uses of the literals, due to the negative offsets used by +PC-relative `L32R' instructions). The `.literal_position' directive +can be used to do this. In the following code, the literal for `M' +will automatically be aligned correctly and is placed after the +unconditional jump. + + .global M + code_start: + j continue + .literal_position + .align 4 + continue: + movi a4, M + + +File: as.info, Node: Literal Prefix Directive, Next: Absolute Literals Directive, Prev: Literal Position Directive, Up: Xtensa Directives + +9.40.5.6 literal_prefix +....................... + +The `literal_prefix' directive allows you to override the default +literal section names, which are derived from the names of the sections +where the literals are defined. + + .begin literal_prefix [NAME] + .end literal_prefix + + For literals defined within the delimited region, the literal section +names are derived from the NAME argument instead of the name of the +current section. The rules used to derive the literal section names do +not change. *Note literal: Literal Directive. If the NAME argument is +omitted, the literal sections revert to the defaults. This directive +has no effect when using the `--text-section-literals' option (*note +Command Line Options: Xtensa Options.). + + +File: as.info, Node: Absolute Literals Directive, Prev: Literal Prefix Directive, Up: Xtensa Directives + +9.40.5.7 absolute-literals +.......................... + +The `absolute-literals' and `no-absolute-literals' directives control +the absolute vs. PC-relative mode for `L32R' instructions. These are +relevant only for Xtensa configurations that include the absolute +addressing option for `L32R' instructions. + + .begin [no-]absolute-literals + .end [no-]absolute-literals + + These directives do not change the `L32R' mode--they only cause the +assembler to emit the appropriate kind of relocation for `L32R' +instructions and to place the literal values in the appropriate section. +To change the `L32R' mode, the program must write the `LITBASE' special +register. It is the programmer's responsibility to keep track of the +mode and indicate to the assembler which mode is used in each region of +code. + + If the Xtensa configuration includes the absolute `L32R' addressing +option, the default is to assume absolute `L32R' addressing unless the +`--no-absolute-literals' command-line option is specified. Otherwise, +the default is to assume PC-relative `L32R' addressing. The +`absolute-literals' directive can then be used to override the default +determined by the command-line options. + + +File: as.info, Node: Reporting Bugs, Next: Acknowledgements, Prev: Machine Dependencies, Up: Top + +10 Reporting Bugs +***************** + +Your bug reports play an essential role in making `as' reliable. + + Reporting a bug may help you by bringing a solution to your problem, +or it may not. But in any case the principal function of a bug report +is to help the entire community by making the next version of `as' work +better. Bug reports are your contribution to the maintenance of `as'. + + In order for a bug report to serve its purpose, you must include the +information that enables us to fix the bug. + +* Menu: + +* Bug Criteria:: Have you found a bug? +* Bug Reporting:: How to report bugs + + +File: as.info, Node: Bug Criteria, Next: Bug Reporting, Up: Reporting Bugs + +10.1 Have You Found a Bug? +========================== + +If you are not sure whether you have found a bug, here are some +guidelines: + + * If the assembler gets a fatal signal, for any input whatever, that + is a `as' bug. Reliable assemblers never crash. + + * If `as' produces an error message for valid input, that is a bug. + + * If `as' does not produce an error message for invalid input, that + is a bug. However, you should note that your idea of "invalid + input" might be our idea of "an extension" or "support for + traditional practice". + + * If you are an experienced user of assemblers, your suggestions for + improvement of `as' are welcome in any case. + + +File: as.info, Node: Bug Reporting, Prev: Bug Criteria, Up: Reporting Bugs + +10.2 How to Report Bugs +======================= + +A number of companies and individuals offer support for GNU products. +If you obtained `as' from a support organization, we recommend you +contact that organization first. + + You can find contact information for many support companies and +individuals in the file `etc/SERVICE' in the GNU Emacs distribution. + + In any event, we also recommend that you send bug reports for `as' +to `http://www.sourceware.org/bugzilla/'. + + The fundamental principle of reporting bugs usefully is this: +*report all the facts*. If you are not sure whether to state a fact or +leave it out, state it! + + Often people omit facts because they think they know what causes the +problem and assume that some details do not matter. Thus, you might +assume that the name of a symbol you use in an example does not matter. +Well, probably it does not, but one cannot be sure. Perhaps the bug +is a stray memory reference which happens to fetch from the location +where that name is stored in memory; perhaps, if the name were +different, the contents of that location would fool the assembler into +doing the right thing despite the bug. Play it safe and give a +specific, complete example. That is the easiest thing for you to do, +and the most helpful. + + Keep in mind that the purpose of a bug report is to enable us to fix +the bug if it is new to us. Therefore, always write your bug reports +on the assumption that the bug has not been reported previously. + + Sometimes people give a few sketchy facts and ask, "Does this ring a +bell?" This cannot help us fix a bug, so it is basically useless. We +respond by asking for enough details to enable us to investigate. You +might as well expedite matters by sending them to begin with. + + To enable us to fix the bug, you should include all these things: + + * The version of `as'. `as' announces it if you start it with the + `--version' argument. + + Without this, we will not know whether there is any point in + looking for the bug in the current version of `as'. + + * Any patches you may have applied to the `as' source. + + * The type of machine you are using, and the operating system name + and version number. + + * What compiler (and its version) was used to compile `as'--e.g. + "`gcc-2.7'". + + * The command arguments you gave the assembler to assemble your + example and observe the bug. To guarantee you will not omit + something important, list them all. A copy of the Makefile (or + the output from make) is sufficient. + + If we were to try to guess the arguments, we would probably guess + wrong and then we might not encounter the bug. + + * A complete input file that will reproduce the bug. If the bug is + observed when the assembler is invoked via a compiler, send the + assembler source, not the high level language source. Most + compilers will produce the assembler source when run with the `-S' + option. If you are using `gcc', use the options `-v + --save-temps'; this will save the assembler source in a file with + an extension of `.s', and also show you exactly how `as' is being + run. + + * A description of what behavior you observe that you believe is + incorrect. For example, "It gets a fatal signal." + + Of course, if the bug is that `as' gets a fatal signal, then we + will certainly notice it. But if the bug is incorrect output, we + might not notice unless it is glaringly wrong. You might as well + not give us a chance to make a mistake. + + Even if the problem you experience is a fatal signal, you should + still say so explicitly. Suppose something strange is going on, + such as, your copy of `as' is out of sync, or you have encountered + a bug in the C library on your system. (This has happened!) Your + copy might crash and ours would not. If you told us to expect a + crash, then when ours fails to crash, we would know that the bug + was not happening for us. If you had not told us to expect a + crash, then we would not be able to draw any conclusion from our + observations. + + * If you wish to suggest changes to the `as' source, send us context + diffs, as generated by `diff' with the `-u', `-c', or `-p' option. + Always send diffs from the old file to the new file. If you even + discuss something in the `as' source, refer to it by context, not + by line number. + + The line numbers in our development sources will not match those + in your sources. Your line numbers would convey no useful + information to us. + + Here are some things that are not necessary: + + * A description of the envelope of the bug. + + Often people who encounter a bug spend a lot of time investigating + which changes to the input file will make the bug go away and which + changes will not affect it. + + This is often time consuming and not very useful, because the way + we will find the bug is by running a single example under the + debugger with breakpoints, not by pure deduction from a series of + examples. We recommend that you save your time for something else. + + Of course, if you can find a simpler example to report _instead_ + of the original one, that is a convenience for us. Errors in the + output will be easier to spot, running under the debugger will take + less time, and so on. + + However, simplification is not vital; if you do not want to do + this, report the bug anyway and send us the entire test case you + used. + + * A patch for the bug. + + A patch for the bug does help us if it is a good one. But do not + omit the necessary information, such as the test case, on the + assumption that a patch is all we need. We might see problems + with your patch and decide to fix the problem another way, or we + might not understand it at all. + + Sometimes with a program as complicated as `as' it is very hard to + construct an example that will make the program follow a certain + path through the code. If you do not send us the example, we will + not be able to construct one, so we will not be able to verify + that the bug is fixed. + + And if we cannot understand what bug you are trying to fix, or why + your patch should be an improvement, we will not install it. A + test case will help us to understand. + + * A guess about what the bug is or what it depends on. + + Such guesses are usually wrong. Even we cannot guess right about + such things without first using the debugger to find the facts. + + +File: as.info, Node: Acknowledgements, Next: GNU Free Documentation License, Prev: Reporting Bugs, Up: Top + +11 Acknowledgements +******************* + +If you have contributed to GAS and your name isn't listed here, it is +not meant as a slight. We just don't know about it. Send mail to the +maintainer, and we'll correct the situation. Currently the maintainer +is Ken Raeburn (email address `raeburn@cygnus.com'). + + Dean Elsner wrote the original GNU assembler for the VAX.(1) + + Jay Fenlason maintained GAS for a while, adding support for +GDB-specific debug information and the 68k series machines, most of the +preprocessing pass, and extensive changes in `messages.c', +`input-file.c', `write.c'. + + K. Richard Pixley maintained GAS for a while, adding various +enhancements and many bug fixes, including merging support for several +processors, breaking GAS up to handle multiple object file format back +ends (including heavy rewrite, testing, an integration of the coff and +b.out back ends), adding configuration including heavy testing and +verification of cross assemblers and file splits and renaming, +converted GAS to strictly ANSI C including full prototypes, added +support for m680[34]0 and cpu32, did considerable work on i960 +including a COFF port (including considerable amounts of reverse +engineering), a SPARC opcode file rewrite, DECstation, rs6000, and +hp300hpux host ports, updated "know" assertions and made them work, +much other reorganization, cleanup, and lint. + + Ken Raeburn wrote the high-level BFD interface code to replace most +of the code in format-specific I/O modules. + + The original VMS support was contributed by David L. Kashtan. Eric +Youngdale has done much work with it since. + + The Intel 80386 machine description was written by Eliot Dresselhaus. + + Minh Tran-Le at IntelliCorp contributed some AIX 386 support. + + The Motorola 88k machine description was contributed by Devon Bowen +of Buffalo University and Torbjorn Granlund of the Swedish Institute of +Computer Science. + + Keith Knowles at the Open Software Foundation wrote the original +MIPS back end (`tc-mips.c', `tc-mips.h'), and contributed Rose format +support (which hasn't been merged in yet). Ralph Campbell worked with +the MIPS code to support a.out format. + + Support for the Zilog Z8k and Renesas H8/300 processors (tc-z8k, +tc-h8300), and IEEE 695 object file format (obj-ieee), was written by +Steve Chamberlain of Cygnus Support. Steve also modified the COFF back +end to use BFD for some low-level operations, for use with the H8/300 +and AMD 29k targets. + + John Gilmore built the AMD 29000 support, added `.include' support, +and simplified the configuration of which versions accept which +directives. He updated the 68k machine description so that Motorola's +opcodes always produced fixed-size instructions (e.g., `jsr'), while +synthetic instructions remained shrinkable (`jbsr'). John fixed many +bugs, including true tested cross-compilation support, and one bug in +relaxation that took a week and required the proverbial one-bit fix. + + Ian Lance Taylor of Cygnus Support merged the Motorola and MIT +syntax for the 68k, completed support for some COFF targets (68k, i386 +SVR3, and SCO Unix), added support for MIPS ECOFF and ELF targets, +wrote the initial RS/6000 and PowerPC assembler, and made a few other +minor patches. + + Steve Chamberlain made GAS able to generate listings. + + Hewlett-Packard contributed support for the HP9000/300. + + Jeff Law wrote GAS and BFD support for the native HPPA object format +(SOM) along with a fairly extensive HPPA testsuite (for both SOM and +ELF object formats). This work was supported by both the Center for +Software Science at the University of Utah and Cygnus Support. + + Support for ELF format files has been worked on by Mark Eichin of +Cygnus Support (original, incomplete implementation for SPARC), Pete +Hoogenboom and Jeff Law at the University of Utah (HPPA mainly), +Michael Meissner of the Open Software Foundation (i386 mainly), and Ken +Raeburn of Cygnus Support (sparc, and some initial 64-bit support). + + Linas Vepstas added GAS support for the ESA/390 "IBM 370" +architecture. + + Richard Henderson rewrote the Alpha assembler. Klaus Kaempf wrote +GAS and BFD support for openVMS/Alpha. + + Timothy Wall, Michael Hayes, and Greg Smart contributed to the +various tic* flavors. + + David Heine, Sterling Augustine, Bob Wilson and John Ruttenberg from +Tensilica, Inc. added support for Xtensa processors. + + Several engineers at Cygnus Support have also provided many small +bug fixes and configuration enhancements. + + Jon Beniston added support for the Lattice Mico32 architecture. + + Many others have contributed large or small bugfixes and +enhancements. If you have contributed significant work and are not +mentioned on this list, and want to be, let us know. Some of the +history has been lost; we are not intentionally leaving anyone out. + + ---------- Footnotes ---------- + + (1) Any more details? + + +File: as.info, Node: GNU Free Documentation License, Next: AS Index, Prev: Acknowledgements, Up: Top + +Appendix A GNU Free Documentation License +***************************************** + + Version 1.3, 3 November 2008 + + Copyright (C) 2000, 2001, 2002, 2007, 2008 Free Software Foundation, Inc. + `http://fsf.org/' + + Everyone is permitted to copy and distribute verbatim copies + of this license document, but changing it is not allowed. + + 0. PREAMBLE + + The purpose of this License is to make a manual, textbook, or other + functional and useful document "free" in the sense of freedom: to + assure everyone the effective freedom to copy and redistribute it, + with or without modifying it, either commercially or + noncommercially. Secondarily, this License preserves for the + author and publisher a way to get credit for their work, while not + being considered responsible for modifications made by others. + + This License is a kind of "copyleft", which means that derivative + works of the document must themselves be free in the same sense. + It complements the GNU General Public License, which is a copyleft + license designed for free software. + + We have designed this License in order to use it for manuals for + free software, because free software needs free documentation: a + free program should come with manuals providing the same freedoms + that the software does. But this License is not limited to + software manuals; it can be used for any textual work, regardless + of subject matter or whether it is published as a printed book. + We recommend this License principally for works whose purpose is + instruction or reference. + + 1. APPLICABILITY AND DEFINITIONS + + This License applies to any manual or other work, in any medium, + that contains a notice placed by the copyright holder saying it + can be distributed under the terms of this License. Such a notice + grants a world-wide, royalty-free license, unlimited in duration, + to use that work under the conditions stated herein. The + "Document", below, refers to any such manual or work. Any member + of the public is a licensee, and is addressed as "you". You + accept the license if you copy, modify or distribute the work in a + way requiring permission under copyright law. + + A "Modified Version" of the Document means any work containing the + Document or a portion of it, either copied verbatim, or with + modifications and/or translated into another language. + + A "Secondary Section" is a named appendix or a front-matter section + of the Document that deals exclusively with the relationship of the + publishers or authors of the Document to the Document's overall + subject (or to related matters) and contains nothing that could + fall directly within that overall subject. (Thus, if the Document + is in part a textbook of mathematics, a Secondary Section may not + explain any mathematics.) The relationship could be a matter of + historical connection with the subject or with related matters, or + of legal, commercial, philosophical, ethical or political position + regarding them. + + The "Invariant Sections" are certain Secondary Sections whose + titles are designated, as being those of Invariant Sections, in + the notice that says that the Document is released under this + License. If a section does not fit the above definition of + Secondary then it is not allowed to be designated as Invariant. + The Document may contain zero Invariant Sections. If the Document + does not identify any Invariant Sections then there are none. + + The "Cover Texts" are certain short passages of text that are + listed, as Front-Cover Texts or Back-Cover Texts, in the notice + that says that the Document is released under this License. A + Front-Cover Text may be at most 5 words, and a Back-Cover Text may + be at most 25 words. + + A "Transparent" copy of the Document means a machine-readable copy, + represented in a format whose specification is available to the + general public, that is suitable for revising the document + straightforwardly with generic text editors or (for images + composed of pixels) generic paint programs or (for drawings) some + widely available drawing editor, and that is suitable for input to + text formatters or for automatic translation to a variety of + formats suitable for input to text formatters. A copy made in an + otherwise Transparent file format whose markup, or absence of + markup, has been arranged to thwart or discourage subsequent + modification by readers is not Transparent. An image format is + not Transparent if used for any substantial amount of text. A + copy that is not "Transparent" is called "Opaque". + + Examples of suitable formats for Transparent copies include plain + ASCII without markup, Texinfo input format, LaTeX input format, + SGML or XML using a publicly available DTD, and + standard-conforming simple HTML, PostScript or PDF designed for + human modification. Examples of transparent image formats include + PNG, XCF and JPG. Opaque formats include proprietary formats that + can be read and edited only by proprietary word processors, SGML or + XML for which the DTD and/or processing tools are not generally + available, and the machine-generated HTML, PostScript or PDF + produced by some word processors for output purposes only. + + The "Title Page" means, for a printed book, the title page itself, + plus such following pages as are needed to hold, legibly, the + material this License requires to appear in the title page. For + works in formats which do not have any title page as such, "Title + Page" means the text near the most prominent appearance of the + work's title, preceding the beginning of the body of the text. + + The "publisher" means any person or entity that distributes copies + of the Document to the public. + + A section "Entitled XYZ" means a named subunit of the Document + whose title either is precisely XYZ or contains XYZ in parentheses + following text that translates XYZ in another language. (Here XYZ + stands for a specific section name mentioned below, such as + "Acknowledgements", "Dedications", "Endorsements", or "History".) + To "Preserve the Title" of such a section when you modify the + Document means that it remains a section "Entitled XYZ" according + to this definition. + + The Document may include Warranty Disclaimers next to the notice + which states that this License applies to the Document. These + Warranty Disclaimers are considered to be included by reference in + this License, but only as regards disclaiming warranties: any other + implication that these Warranty Disclaimers may have is void and + has no effect on the meaning of this License. + + 2. VERBATIM COPYING + + You may copy and distribute the Document in any medium, either + commercially or noncommercially, provided that this License, the + copyright notices, and the license notice saying this License + applies to the Document are reproduced in all copies, and that you + add no other conditions whatsoever to those of this License. You + may not use technical measures to obstruct or control the reading + or further copying of the copies you make or distribute. However, + you may accept compensation in exchange for copies. If you + distribute a large enough number of copies you must also follow + the conditions in section 3. + + You may also lend copies, under the same conditions stated above, + and you may publicly display copies. + + 3. COPYING IN QUANTITY + + If you publish printed copies (or copies in media that commonly + have printed covers) of the Document, numbering more than 100, and + the Document's license notice requires Cover Texts, you must + enclose the copies in covers that carry, clearly and legibly, all + these Cover Texts: Front-Cover Texts on the front cover, and + Back-Cover Texts on the back cover. Both covers must also clearly + and legibly identify you as the publisher of these copies. The + front cover must present the full title with all words of the + title equally prominent and visible. You may add other material + on the covers in addition. Copying with changes limited to the + covers, as long as they preserve the title of the Document and + satisfy these conditions, can be treated as verbatim copying in + other respects. + + If the required texts for either cover are too voluminous to fit + legibly, you should put the first ones listed (as many as fit + reasonably) on the actual cover, and continue the rest onto + adjacent pages. + + If you publish or distribute Opaque copies of the Document + numbering more than 100, you must either include a + machine-readable Transparent copy along with each Opaque copy, or + state in or with each Opaque copy a computer-network location from + which the general network-using public has access to download + using public-standard network protocols a complete Transparent + copy of the Document, free of added material. If you use the + latter option, you must take reasonably prudent steps, when you + begin distribution of Opaque copies in quantity, to ensure that + this Transparent copy will remain thus accessible at the stated + location until at least one year after the last time you + distribute an Opaque copy (directly or through your agents or + retailers) of that edition to the public. + + It is requested, but not required, that you contact the authors of + the Document well before redistributing any large number of + copies, to give them a chance to provide you with an updated + version of the Document. + + 4. MODIFICATIONS + + You may copy and distribute a Modified Version of the Document + under the conditions of sections 2 and 3 above, provided that you + release the Modified Version under precisely this License, with + the Modified Version filling the role of the Document, thus + licensing distribution and modification of the Modified Version to + whoever possesses a copy of it. In addition, you must do these + things in the Modified Version: + + A. Use in the Title Page (and on the covers, if any) a title + distinct from that of the Document, and from those of + previous versions (which should, if there were any, be listed + in the History section of the Document). You may use the + same title as a previous version if the original publisher of + that version gives permission. + + B. List on the Title Page, as authors, one or more persons or + entities responsible for authorship of the modifications in + the Modified Version, together with at least five of the + principal authors of the Document (all of its principal + authors, if it has fewer than five), unless they release you + from this requirement. + + C. State on the Title page the name of the publisher of the + Modified Version, as the publisher. + + D. Preserve all the copyright notices of the Document. + + E. Add an appropriate copyright notice for your modifications + adjacent to the other copyright notices. + + F. Include, immediately after the copyright notices, a license + notice giving the public permission to use the Modified + Version under the terms of this License, in the form shown in + the Addendum below. + + G. Preserve in that license notice the full lists of Invariant + Sections and required Cover Texts given in the Document's + license notice. + + H. Include an unaltered copy of this License. + + I. Preserve the section Entitled "History", Preserve its Title, + and add to it an item stating at least the title, year, new + authors, and publisher of the Modified Version as given on + the Title Page. If there is no section Entitled "History" in + the Document, create one stating the title, year, authors, + and publisher of the Document as given on its Title Page, + then add an item describing the Modified Version as stated in + the previous sentence. + + J. Preserve the network location, if any, given in the Document + for public access to a Transparent copy of the Document, and + likewise the network locations given in the Document for + previous versions it was based on. These may be placed in + the "History" section. You may omit a network location for a + work that was published at least four years before the + Document itself, or if the original publisher of the version + it refers to gives permission. + + K. For any section Entitled "Acknowledgements" or "Dedications", + Preserve the Title of the section, and preserve in the + section all the substance and tone of each of the contributor + acknowledgements and/or dedications given therein. + + L. Preserve all the Invariant Sections of the Document, + unaltered in their text and in their titles. Section numbers + or the equivalent are not considered part of the section + titles. + + M. Delete any section Entitled "Endorsements". Such a section + may not be included in the Modified Version. + + N. Do not retitle any existing section to be Entitled + "Endorsements" or to conflict in title with any Invariant + Section. + + O. Preserve any Warranty Disclaimers. + + If the Modified Version includes new front-matter sections or + appendices that qualify as Secondary Sections and contain no + material copied from the Document, you may at your option + designate some or all of these sections as invariant. To do this, + add their titles to the list of Invariant Sections in the Modified + Version's license notice. These titles must be distinct from any + other section titles. + + You may add a section Entitled "Endorsements", provided it contains + nothing but endorsements of your Modified Version by various + parties--for example, statements of peer review or that the text + has been approved by an organization as the authoritative + definition of a standard. + + You may add a passage of up to five words as a Front-Cover Text, + and a passage of up to 25 words as a Back-Cover Text, to the end + of the list of Cover Texts in the Modified Version. Only one + passage of Front-Cover Text and one of Back-Cover Text may be + added by (or through arrangements made by) any one entity. If the + Document already includes a cover text for the same cover, + previously added by you or by arrangement made by the same entity + you are acting on behalf of, you may not add another; but you may + replace the old one, on explicit permission from the previous + publisher that added the old one. + + The author(s) and publisher(s) of the Document do not by this + License give permission to use their names for publicity for or to + assert or imply endorsement of any Modified Version. + + 5. COMBINING DOCUMENTS + + You may combine the Document with other documents released under + this License, under the terms defined in section 4 above for + modified versions, provided that you include in the combination + all of the Invariant Sections of all of the original documents, + unmodified, and list them all as Invariant Sections of your + combined work in its license notice, and that you preserve all + their Warranty Disclaimers. + + The combined work need only contain one copy of this License, and + multiple identical Invariant Sections may be replaced with a single + copy. If there are multiple Invariant Sections with the same name + but different contents, make the title of each such section unique + by adding at the end of it, in parentheses, the name of the + original author or publisher of that section if known, or else a + unique number. Make the same adjustment to the section titles in + the list of Invariant Sections in the license notice of the + combined work. + + In the combination, you must combine any sections Entitled + "History" in the various original documents, forming one section + Entitled "History"; likewise combine any sections Entitled + "Acknowledgements", and any sections Entitled "Dedications". You + must delete all sections Entitled "Endorsements." + + 6. COLLECTIONS OF DOCUMENTS + + You may make a collection consisting of the Document and other + documents released under this License, and replace the individual + copies of this License in the various documents with a single copy + that is included in the collection, provided that you follow the + rules of this License for verbatim copying of each of the + documents in all other respects. + + You may extract a single document from such a collection, and + distribute it individually under this License, provided you insert + a copy of this License into the extracted document, and follow + this License in all other respects regarding verbatim copying of + that document. + + 7. AGGREGATION WITH INDEPENDENT WORKS + + A compilation of the Document or its derivatives with other + separate and independent documents or works, in or on a volume of + a storage or distribution medium, is called an "aggregate" if the + copyright resulting from the compilation is not used to limit the + legal rights of the compilation's users beyond what the individual + works permit. When the Document is included in an aggregate, this + License does not apply to the other works in the aggregate which + are not themselves derivative works of the Document. + + If the Cover Text requirement of section 3 is applicable to these + copies of the Document, then if the Document is less than one half + of the entire aggregate, the Document's Cover Texts may be placed + on covers that bracket the Document within the aggregate, or the + electronic equivalent of covers if the Document is in electronic + form. Otherwise they must appear on printed covers that bracket + the whole aggregate. + + 8. TRANSLATION + + Translation is considered a kind of modification, so you may + distribute translations of the Document under the terms of section + 4. Replacing Invariant Sections with translations requires special + permission from their copyright holders, but you may include + translations of some or all Invariant Sections in addition to the + original versions of these Invariant Sections. You may include a + translation of this License, and all the license notices in the + Document, and any Warranty Disclaimers, provided that you also + include the original English version of this License and the + original versions of those notices and disclaimers. In case of a + disagreement between the translation and the original version of + this License or a notice or disclaimer, the original version will + prevail. + + If a section in the Document is Entitled "Acknowledgements", + "Dedications", or "History", the requirement (section 4) to + Preserve its Title (section 1) will typically require changing the + actual title. + + 9. TERMINATION + + You may not copy, modify, sublicense, or distribute the Document + except as expressly provided under this License. Any attempt + otherwise to copy, modify, sublicense, or distribute it is void, + and will automatically terminate your rights under this License. + + However, if you cease all violation of this License, then your + license from a particular copyright holder is reinstated (a) + provisionally, unless and until the copyright holder explicitly + and finally terminates your license, and (b) permanently, if the + copyright holder fails to notify you of the violation by some + reasonable means prior to 60 days after the cessation. + + Moreover, your license from a particular copyright holder is + reinstated permanently if the copyright holder notifies you of the + violation by some reasonable means, this is the first time you have + received notice of violation of this License (for any work) from + that copyright holder, and you cure the violation prior to 30 days + after your receipt of the notice. + + Termination of your rights under this section does not terminate + the licenses of parties who have received copies or rights from + you under this License. If your rights have been terminated and + not permanently reinstated, receipt of a copy of some or all of + the same material does not give you any rights to use it. + + 10. FUTURE REVISIONS OF THIS LICENSE + + The Free Software Foundation may publish new, revised versions of + the GNU Free Documentation License from time to time. Such new + versions will be similar in spirit to the present version, but may + differ in detail to address new problems or concerns. See + `http://www.gnu.org/copyleft/'. + + Each version of the License is given a distinguishing version + number. If the Document specifies that a particular numbered + version of this License "or any later version" applies to it, you + have the option of following the terms and conditions either of + that specified version or of any later version that has been + published (not as a draft) by the Free Software Foundation. If + the Document does not specify a version number of this License, + you may choose any version ever published (not as a draft) by the + Free Software Foundation. If the Document specifies that a proxy + can decide which future versions of this License can be used, that + proxy's public statement of acceptance of a version permanently + authorizes you to choose that version for the Document. + + 11. RELICENSING + + "Massive Multiauthor Collaboration Site" (or "MMC Site") means any + World Wide Web server that publishes copyrightable works and also + provides prominent facilities for anybody to edit those works. A + public wiki that anybody can edit is an example of such a server. + A "Massive Multiauthor Collaboration" (or "MMC") contained in the + site means any set of copyrightable works thus published on the MMC + site. + + "CC-BY-SA" means the Creative Commons Attribution-Share Alike 3.0 + license published by Creative Commons Corporation, a not-for-profit + corporation with a principal place of business in San Francisco, + California, as well as future copyleft versions of that license + published by that same organization. + + "Incorporate" means to publish or republish a Document, in whole or + in part, as part of another Document. + + An MMC is "eligible for relicensing" if it is licensed under this + License, and if all works that were first published under this + License somewhere other than this MMC, and subsequently + incorporated in whole or in part into the MMC, (1) had no cover + texts or invariant sections, and (2) were thus incorporated prior + to November 1, 2008. + + The operator of an MMC Site may republish an MMC contained in the + site under CC-BY-SA on the same site at any time before August 1, + 2009, provided the MMC is eligible for relicensing. + + +ADDENDUM: How to use this License for your documents +==================================================== + +To use this License in a document you have written, include a copy of +the License in the document and put the following copyright and license +notices just after the title page: + + Copyright (C) YEAR YOUR NAME. + Permission is granted to copy, distribute and/or modify this document + under the terms of the GNU Free Documentation License, Version 1.3 + or any later version published by the Free Software Foundation; + with no Invariant Sections, no Front-Cover Texts, and no Back-Cover + Texts. A copy of the license is included in the section entitled ``GNU + Free Documentation License''. + + If you have Invariant Sections, Front-Cover Texts and Back-Cover +Texts, replace the "with...Texts." line with this: + + with the Invariant Sections being LIST THEIR TITLES, with + the Front-Cover Texts being LIST, and with the Back-Cover Texts + being LIST. + + If you have Invariant Sections without Cover Texts, or some other +combination of the three, merge those two alternatives to suit the +situation. + + If your document contains nontrivial examples of program code, we +recommend releasing these examples in parallel under your choice of +free software license, such as the GNU General Public License, to +permit their use in free software. + + +File: as.info, Node: AS Index, Prev: GNU Free Documentation License, Up: Top + +AS Index +******** + + +* Menu: + +* #: Comments. (line 39) +* #APP: Preprocessing. (line 27) +* #NO_APP: Preprocessing. (line 27) +* $ in symbol names <1>: D30V-Chars. (line 63) +* $ in symbol names <2>: SH64-Chars. (line 10) +* $ in symbol names <3>: D10V-Chars. (line 46) +* $ in symbol names: SH-Chars. (line 10) +* $a: ARM Mapping Symbols. (line 9) +* $acos math builtin, TIC54X: TIC54X-Builtins. (line 10) +* $asin math builtin, TIC54X: TIC54X-Builtins. (line 13) +* $atan math builtin, TIC54X: TIC54X-Builtins. (line 16) +* $atan2 math builtin, TIC54X: TIC54X-Builtins. (line 19) +* $ceil math builtin, TIC54X: TIC54X-Builtins. (line 22) +* $cos math builtin, TIC54X: TIC54X-Builtins. (line 28) +* $cosh math builtin, TIC54X: TIC54X-Builtins. (line 25) +* $cvf math builtin, TIC54X: TIC54X-Builtins. (line 31) +* $cvi math builtin, TIC54X: TIC54X-Builtins. (line 34) +* $d: ARM Mapping Symbols. (line 15) +* $exp math builtin, TIC54X: TIC54X-Builtins. (line 37) +* $fabs math builtin, TIC54X: TIC54X-Builtins. (line 40) +* $firstch subsym builtin, TIC54X: TIC54X-Macros. (line 26) +* $floor math builtin, TIC54X: TIC54X-Builtins. (line 43) +* $fmod math builtin, TIC54X: TIC54X-Builtins. (line 47) +* $int math builtin, TIC54X: TIC54X-Builtins. (line 50) +* $iscons subsym builtin, TIC54X: TIC54X-Macros. (line 43) +* $isdefed subsym builtin, TIC54X: TIC54X-Macros. (line 34) +* $ismember subsym builtin, TIC54X: TIC54X-Macros. (line 38) +* $isname subsym builtin, TIC54X: TIC54X-Macros. (line 47) +* $isreg subsym builtin, TIC54X: TIC54X-Macros. (line 50) +* $lastch subsym builtin, TIC54X: TIC54X-Macros. (line 30) +* $ldexp math builtin, TIC54X: TIC54X-Builtins. (line 53) +* $log math builtin, TIC54X: TIC54X-Builtins. (line 59) +* $log10 math builtin, TIC54X: TIC54X-Builtins. (line 56) +* $max math builtin, TIC54X: TIC54X-Builtins. (line 62) +* $min math builtin, TIC54X: TIC54X-Builtins. (line 65) +* $pow math builtin, TIC54X: TIC54X-Builtins. (line 68) +* $round math builtin, TIC54X: TIC54X-Builtins. (line 71) +* $sgn math builtin, TIC54X: TIC54X-Builtins. (line 74) +* $sin math builtin, TIC54X: TIC54X-Builtins. (line 77) +* $sinh math builtin, TIC54X: TIC54X-Builtins. (line 80) +* $sqrt math builtin, TIC54X: TIC54X-Builtins. (line 83) +* $structacc subsym builtin, TIC54X: TIC54X-Macros. (line 57) +* $structsz subsym builtin, TIC54X: TIC54X-Macros. (line 54) +* $symcmp subsym builtin, TIC54X: TIC54X-Macros. (line 23) +* $symlen subsym builtin, TIC54X: TIC54X-Macros. (line 20) +* $t: ARM Mapping Symbols. (line 12) +* $tan math builtin, TIC54X: TIC54X-Builtins. (line 86) +* $tanh math builtin, TIC54X: TIC54X-Builtins. (line 89) +* $trunc math builtin, TIC54X: TIC54X-Builtins. (line 92) +* -+ option, VAX/VMS: VAX-Opts. (line 71) +* --: Command Line. (line 10) +* --32 option, i386: i386-Options. (line 8) +* --32 option, x86-64: i386-Options. (line 8) +* --64 option, i386: i386-Options. (line 8) +* --64 option, x86-64: i386-Options. (line 8) +* --absolute-literals: Xtensa Options. (line 23) +* --allow-reg-prefix: SH Options. (line 9) +* --alternate: alternate. (line 6) +* --base-size-default-16: M68K-Opts. (line 71) +* --base-size-default-32: M68K-Opts. (line 71) +* --big: SH Options. (line 9) +* --bitwise-or option, M680x0: M68K-Opts. (line 64) +* --disp-size-default-16: M68K-Opts. (line 80) +* --disp-size-default-32: M68K-Opts. (line 80) +* --divide option, i386: i386-Options. (line 24) +* --dsp: SH Options. (line 9) +* --emulation=crisaout command line option, CRIS: CRIS-Opts. (line 9) +* --emulation=criself command line option, CRIS: CRIS-Opts. (line 9) +* --enforce-aligned-data: Sparc-Aligned-Data. (line 11) +* --fatal-warnings: W. (line 16) +* --fix-v4bx command line option, ARM: ARM Options. (line 143) +* --fixed-special-register-names command line option, MMIX: MMIX-Opts. + (line 8) +* --force-long-branches: M68HC11-Opts. (line 69) +* --generate-example: M68HC11-Opts. (line 86) +* --globalize-symbols command line option, MMIX: MMIX-Opts. (line 12) +* --gnu-syntax command line option, MMIX: MMIX-Opts. (line 16) +* --hash-size=NUMBER: Overview. (line 326) +* --linker-allocated-gregs command line option, MMIX: MMIX-Opts. + (line 67) +* --listing-cont-lines: listing. (line 34) +* --listing-lhs-width: listing. (line 16) +* --listing-lhs-width2: listing. (line 21) +* --listing-rhs-width: listing. (line 28) +* --little: SH Options. (line 9) +* --longcalls: Xtensa Options. (line 37) +* --march=ARCHITECTURE command line option, CRIS: CRIS-Opts. (line 33) +* --MD: MD. (line 6) +* --mul-bug-abort command line option, CRIS: CRIS-Opts. (line 61) +* --no-absolute-literals: Xtensa Options. (line 23) +* --no-expand command line option, MMIX: MMIX-Opts. (line 31) +* --no-longcalls: Xtensa Options. (line 37) +* --no-merge-gregs command line option, MMIX: MMIX-Opts. (line 36) +* --no-mul-bug-abort command line option, CRIS: CRIS-Opts. (line 61) +* --no-predefined-syms command line option, MMIX: MMIX-Opts. (line 22) +* --no-pushj-stubs command line option, MMIX: MMIX-Opts. (line 54) +* --no-stubs command line option, MMIX: MMIX-Opts. (line 54) +* --no-target-align: Xtensa Options. (line 30) +* --no-text-section-literals: Xtensa Options. (line 9) +* --no-transform: Xtensa Options. (line 46) +* --no-underscore command line option, CRIS: CRIS-Opts. (line 15) +* --no-warn: W. (line 11) +* --pcrel: M68K-Opts. (line 92) +* --pic command line option, CRIS: CRIS-Opts. (line 27) +* --print-insn-syntax: M68HC11-Opts. (line 75) +* --print-opcodes: M68HC11-Opts. (line 79) +* --register-prefix-optional option, M680x0: M68K-Opts. (line 51) +* --relax: SH Options. (line 9) +* --relax command line option, MMIX: MMIX-Opts. (line 19) +* --rename-section: Xtensa Options. (line 54) +* --renesas: SH Options. (line 9) +* --short-branches: M68HC11-Opts. (line 54) +* --small: SH Options. (line 9) +* --statistics: statistics. (line 6) +* --strict-direct-mode: M68HC11-Opts. (line 44) +* --target-align: Xtensa Options. (line 30) +* --text-section-literals: Xtensa Options. (line 9) +* --traditional-format: traditional-format. (line 6) +* --transform: Xtensa Options. (line 46) +* --underscore command line option, CRIS: CRIS-Opts. (line 15) +* --warn: W. (line 19) +* -1 option, VAX/VMS: VAX-Opts. (line 77) +* -32addr command line option, Alpha: Alpha Options. (line 58) +* -a: a. (line 6) +* -A options, i960: Options-i960. (line 6) +* -ac: a. (line 6) +* -ad: a. (line 6) +* -ag: a. (line 6) +* -ah: a. (line 6) +* -al: a. (line 6) +* -an: a. (line 6) +* -as: a. (line 6) +* -Asparclet: Sparc-Opts. (line 25) +* -Asparclite: Sparc-Opts. (line 25) +* -Av6: Sparc-Opts. (line 25) +* -Av8: Sparc-Opts. (line 25) +* -Av9: Sparc-Opts. (line 25) +* -Av9a: Sparc-Opts. (line 25) +* -b option, i960: Options-i960. (line 22) +* -big option, M32R: M32R-Opts. (line 35) +* -D: D. (line 6) +* -D, ignored on VAX: VAX-Opts. (line 11) +* -d, VAX option: VAX-Opts. (line 16) +* -eabi= command line option, ARM: ARM Options. (line 126) +* -EB command line option, ARC: ARC Options. (line 31) +* -EB command line option, ARM: ARM Options. (line 131) +* -EB option (MIPS): MIPS Opts. (line 13) +* -EB option, M32R: M32R-Opts. (line 39) +* -EL command line option, ARC: ARC Options. (line 35) +* -EL command line option, ARM: ARM Options. (line 135) +* -EL option (MIPS): MIPS Opts. (line 13) +* -EL option, M32R: M32R-Opts. (line 32) +* -f: f. (line 6) +* -F command line option, Alpha: Alpha Options. (line 58) +* -G command line option, Alpha: Alpha Options. (line 54) +* -g command line option, Alpha: Alpha Options. (line 48) +* -G option (MIPS): MIPS Opts. (line 8) +* -H option, VAX/VMS: VAX-Opts. (line 81) +* -h option, VAX/VMS: VAX-Opts. (line 45) +* -I PATH: I. (line 6) +* -ignore-parallel-conflicts option, M32RX: M32R-Opts. (line 87) +* -Ip option, M32RX: M32R-Opts. (line 97) +* -J, ignored on VAX: VAX-Opts. (line 27) +* -K: K. (line 6) +* -k command line option, ARM: ARM Options. (line 139) +* -KPIC option, M32R: M32R-Opts. (line 42) +* -KPIC option, MIPS: MIPS Opts. (line 21) +* -L: L. (line 6) +* -l option, M680x0: M68K-Opts. (line 39) +* -little option, M32R: M32R-Opts. (line 27) +* -M: M. (line 6) +* -m11/03: PDP-11-Options. (line 140) +* -m11/04: PDP-11-Options. (line 143) +* -m11/05: PDP-11-Options. (line 146) +* -m11/10: PDP-11-Options. (line 146) +* -m11/15: PDP-11-Options. (line 149) +* -m11/20: PDP-11-Options. (line 149) +* -m11/21: PDP-11-Options. (line 152) +* -m11/23: PDP-11-Options. (line 155) +* -m11/24: PDP-11-Options. (line 155) +* -m11/34: PDP-11-Options. (line 158) +* -m11/34a: PDP-11-Options. (line 161) +* -m11/35: PDP-11-Options. (line 164) +* -m11/40: PDP-11-Options. (line 164) +* -m11/44: PDP-11-Options. (line 167) +* -m11/45: PDP-11-Options. (line 170) +* -m11/50: PDP-11-Options. (line 170) +* -m11/53: PDP-11-Options. (line 173) +* -m11/55: PDP-11-Options. (line 170) +* -m11/60: PDP-11-Options. (line 176) +* -m11/70: PDP-11-Options. (line 170) +* -m11/73: PDP-11-Options. (line 173) +* -m11/83: PDP-11-Options. (line 173) +* -m11/84: PDP-11-Options. (line 173) +* -m11/93: PDP-11-Options. (line 173) +* -m11/94: PDP-11-Options. (line 173) +* -m16c option, M16C: M32C-Opts. (line 12) +* -m31 option, s390: s390 Options. (line 8) +* -m32c option, M32C: M32C-Opts. (line 9) +* -m32r option, M32R: M32R-Opts. (line 21) +* -m32rx option, M32R2: M32R-Opts. (line 17) +* -m32rx option, M32RX: M32R-Opts. (line 9) +* -m64 option, s390: s390 Options. (line 8) +* -m68000 and related options: M68K-Opts. (line 104) +* -m68hc11: M68HC11-Opts. (line 9) +* -m68hc12: M68HC11-Opts. (line 14) +* -m68hcs12: M68HC11-Opts. (line 21) +* -m[no-]68851 command line option, M680x0: M68K-Opts. (line 21) +* -m[no-]68881 command line option, M680x0: M68K-Opts. (line 21) +* -m[no-]div command line option, M680x0: M68K-Opts. (line 21) +* -m[no-]emac command line option, M680x0: M68K-Opts. (line 21) +* -m[no-]float command line option, M680x0: M68K-Opts. (line 21) +* -m[no-]mac command line option, M680x0: M68K-Opts. (line 21) +* -m[no-]usp command line option, M680x0: M68K-Opts. (line 21) +* -mall: PDP-11-Options. (line 26) +* -mall-enabled command line option, LM32: LM32 Options. (line 30) +* -mall-extensions: PDP-11-Options. (line 26) +* -mall-opcodes command line option, AVR: AVR Options. (line 62) +* -mapcs command line option, ARM: ARM Options. (line 99) +* -mapcs-float command line option, ARM: ARM Options. (line 112) +* -mapcs-reentrant command line option, ARM: ARM Options. (line 117) +* -marc[5|6|7|8] command line option, ARC: ARC Options. (line 6) +* -march= command line option, ARM: ARM Options. (line 40) +* -march= command line option, M680x0: M68K-Opts. (line 8) +* -march= option, i386: i386-Options. (line 31) +* -march= option, s390: s390 Options. (line 25) +* -march= option, x86-64: i386-Options. (line 31) +* -matpcs command line option, ARM: ARM Options. (line 104) +* -mbarrel-shift-enabled command line option, LM32: LM32 Options. + (line 12) +* -mbreak-enabled command line option, LM32: LM32 Options. (line 27) +* -mcis: PDP-11-Options. (line 32) +* -mconstant-gp command line option, IA-64: IA-64 Options. (line 6) +* -mCPU command line option, Alpha: Alpha Options. (line 6) +* -mcpu option, cpu: TIC54X-Opts. (line 15) +* -mcpu= command line option, ARM: ARM Options. (line 6) +* -mcpu= command line option, Blackfin: Blackfin Options. (line 6) +* -mcpu= command line option, M680x0: M68K-Opts. (line 14) +* -mcsm: PDP-11-Options. (line 43) +* -mdcache-enabled command line option, LM32: LM32 Options. (line 24) +* -mdebug command line option, Alpha: Alpha Options. (line 25) +* -mdivide-enabled command line option, LM32: LM32 Options. (line 9) +* -me option, stderr redirect: TIC54X-Opts. (line 20) +* -meis: PDP-11-Options. (line 46) +* -merrors-to-file option, stderr redirect: TIC54X-Opts. (line 20) +* -mesa option, s390: s390 Options. (line 17) +* -mf option, far-mode: TIC54X-Opts. (line 8) +* -mf11: PDP-11-Options. (line 122) +* -mfar-mode option, far-mode: TIC54X-Opts. (line 8) +* -mfis: PDP-11-Options. (line 51) +* -mfloat-abi= command line option, ARM: ARM Options. (line 121) +* -mfp-11: PDP-11-Options. (line 56) +* -mfpp: PDP-11-Options. (line 56) +* -mfpu: PDP-11-Options. (line 56) +* -mfpu= command line option, ARM: ARM Options. (line 55) +* -micache-enabled command line option, LM32: LM32 Options. (line 21) +* -mimplicit-it command line option, ARM: ARM Options. (line 83) +* -mip2022 option, IP2K: IP2K-Opts. (line 14) +* -mip2022ext option, IP2022: IP2K-Opts. (line 9) +* -mj11: PDP-11-Options. (line 126) +* -mka11: PDP-11-Options. (line 92) +* -mkb11: PDP-11-Options. (line 95) +* -mkd11a: PDP-11-Options. (line 98) +* -mkd11b: PDP-11-Options. (line 101) +* -mkd11d: PDP-11-Options. (line 104) +* -mkd11e: PDP-11-Options. (line 107) +* -mkd11f: PDP-11-Options. (line 110) +* -mkd11h: PDP-11-Options. (line 110) +* -mkd11k: PDP-11-Options. (line 114) +* -mkd11q: PDP-11-Options. (line 110) +* -mkd11z: PDP-11-Options. (line 118) +* -mkev11: PDP-11-Options. (line 51) +* -mlimited-eis: PDP-11-Options. (line 64) +* -mlong: M68HC11-Opts. (line 32) +* -mlong-double: M68HC11-Opts. (line 40) +* -mmcu= command line option, AVR: AVR Options. (line 6) +* -mmfpt: PDP-11-Options. (line 70) +* -mmicrocode: PDP-11-Options. (line 83) +* -mmnemonic= option, i386: i386-Options. (line 80) +* -mmnemonic= option, x86-64: i386-Options. (line 80) +* -mmultiply-enabled command line option, LM32: LM32 Options. (line 6) +* -mmutiproc: PDP-11-Options. (line 73) +* -mmxps: PDP-11-Options. (line 77) +* -mnaked-reg option, i386: i386-Options. (line 94) +* -mnaked-reg option, x86-64: i386-Options. (line 94) +* -mno-cis: PDP-11-Options. (line 32) +* -mno-csm: PDP-11-Options. (line 43) +* -mno-eis: PDP-11-Options. (line 46) +* -mno-extensions: PDP-11-Options. (line 29) +* -mno-fis: PDP-11-Options. (line 51) +* -mno-fp-11: PDP-11-Options. (line 56) +* -mno-fpp: PDP-11-Options. (line 56) +* -mno-fpu: PDP-11-Options. (line 56) +* -mno-kev11: PDP-11-Options. (line 51) +* -mno-limited-eis: PDP-11-Options. (line 64) +* -mno-mfpt: PDP-11-Options. (line 70) +* -mno-microcode: PDP-11-Options. (line 83) +* -mno-mutiproc: PDP-11-Options. (line 73) +* -mno-mxps: PDP-11-Options. (line 77) +* -mno-pic: PDP-11-Options. (line 11) +* -mno-regnames option, s390: s390 Options. (line 35) +* -mno-skip-bug command line option, AVR: AVR Options. (line 65) +* -mno-spl: PDP-11-Options. (line 80) +* -mno-sym32: MIPS Opts. (line 189) +* -mno-wrap command line option, AVR: AVR Options. (line 68) +* -mpic: PDP-11-Options. (line 11) +* -mregnames option, s390: s390 Options. (line 32) +* -mrelax command line option, V850: V850 Options. (line 51) +* -mshort: M68HC11-Opts. (line 27) +* -mshort-double: M68HC11-Opts. (line 36) +* -msign-extend-enabled command line option, LM32: LM32 Options. + (line 15) +* -mspl: PDP-11-Options. (line 80) +* -msse-check= option, i386: i386-Options. (line 68) +* -msse-check= option, x86-64: i386-Options. (line 68) +* -msse2avx option, i386: i386-Options. (line 64) +* -msse2avx option, x86-64: i386-Options. (line 64) +* -msym32: MIPS Opts. (line 189) +* -msyntax= option, i386: i386-Options. (line 87) +* -msyntax= option, x86-64: i386-Options. (line 87) +* -mt11: PDP-11-Options. (line 130) +* -mthumb command line option, ARM: ARM Options. (line 74) +* -mthumb-interwork command line option, ARM: ARM Options. (line 79) +* -mtune= option, i386: i386-Options. (line 56) +* -mtune= option, x86-64: i386-Options. (line 56) +* -muser-enabled command line option, LM32: LM32 Options. (line 18) +* -mv850 command line option, V850: V850 Options. (line 23) +* -mv850any command line option, V850: V850 Options. (line 41) +* -mv850e command line option, V850: V850 Options. (line 29) +* -mv850e1 command line option, V850: V850 Options. (line 35) +* -mvxworks-pic option, MIPS: MIPS Opts. (line 26) +* -mwarn-areg-zero option, s390: s390 Options. (line 38) +* -mwarn-deprecated command line option, ARM: ARM Options. (line 147) +* -mzarch option, s390: s390 Options. (line 17) +* -N command line option, CRIS: CRIS-Opts. (line 57) +* -nIp option, M32RX: M32R-Opts. (line 101) +* -no-bitinst, M32R2: M32R-Opts. (line 54) +* -no-ignore-parallel-conflicts option, M32RX: M32R-Opts. (line 93) +* -no-mdebug command line option, Alpha: Alpha Options. (line 25) +* -no-parallel option, M32RX: M32R-Opts. (line 51) +* -no-relax option, i960: Options-i960. (line 66) +* -no-warn-explicit-parallel-conflicts option, M32RX: M32R-Opts. + (line 79) +* -no-warn-unmatched-high option, M32R: M32R-Opts. (line 111) +* -nocpp ignored (MIPS): MIPS Opts. (line 192) +* -noreplace command line option, Alpha: Alpha Options. (line 40) +* -o: o. (line 6) +* -O option, M32RX: M32R-Opts. (line 59) +* -parallel option, M32RX: M32R-Opts. (line 46) +* -R: R. (line 6) +* -r800 command line option, Z80: Z80 Options. (line 41) +* -relax command line option, Alpha: Alpha Options. (line 32) +* -replace command line option, Alpha: Alpha Options. (line 40) +* -S, ignored on VAX: VAX-Opts. (line 11) +* -t, ignored on VAX: VAX-Opts. (line 36) +* -T, ignored on VAX: VAX-Opts. (line 11) +* -v: v. (line 6) +* -V, redundant on VAX: VAX-Opts. (line 22) +* -version: v. (line 6) +* -W: W. (line 11) +* -warn-explicit-parallel-conflicts option, M32RX: M32R-Opts. (line 65) +* -warn-unmatched-high option, M32R: M32R-Opts. (line 105) +* -Wnp option, M32RX: M32R-Opts. (line 83) +* -Wnuh option, M32RX: M32R-Opts. (line 117) +* -Wp option, M32RX: M32R-Opts. (line 75) +* -wsigned_overflow command line option, V850: V850 Options. (line 9) +* -Wuh option, M32RX: M32R-Opts. (line 114) +* -wunsigned_overflow command line option, V850: V850 Options. + (line 16) +* -x command line option, MMIX: MMIX-Opts. (line 44) +* -z80 command line option, Z80: Z80 Options. (line 8) +* -z8001 command line option, Z8000: Z8000 Options. (line 6) +* -z8002 command line option, Z8000: Z8000 Options. (line 9) +* . (symbol): Dot. (line 6) +* .2byte directive, ARM: ARM Directives. (line 6) +* .4byte directive, ARM: ARM Directives. (line 6) +* .8byte directive, ARM: ARM Directives. (line 6) +* .align directive, ARM: ARM Directives. (line 11) +* .arch directive, ARM: ARM Directives. (line 18) +* .arm directive, ARM: ARM Directives. (line 22) +* .big directive, M32RX: M32R-Directives. (line 88) +* .bss directive, ARM: ARM Directives. (line 30) +* .cantunwind directive, ARM: ARM Directives. (line 33) +* .code directive, ARM: ARM Directives. (line 37) +* .cpu directive, ARM: ARM Directives. (line 41) +* .dn and .qn directives, ARM: ARM Directives. (line 45) +* .eabi_attribute directive, ARM: ARM Directives. (line 69) +* .even directive, ARM: ARM Directives. (line 93) +* .extend directive, ARM: ARM Directives. (line 96) +* .fnend directive, ARM: ARM Directives. (line 102) +* .fnstart directive, ARM: ARM Directives. (line 111) +* .force_thumb directive, ARM: ARM Directives. (line 114) +* .fpu directive, ARM: ARM Directives. (line 118) +* .global: MIPS insn. (line 12) +* .handlerdata directive, ARM: ARM Directives. (line 122) +* .insn: MIPS insn. (line 6) +* .insn directive, s390: s390 Directives. (line 11) +* .inst directive, ARM: ARM Directives. (line 131) +* .ldouble directive, ARM: ARM Directives. (line 96) +* .little directive, M32RX: M32R-Directives. (line 82) +* .long directive, s390: s390 Directives. (line 16) +* .ltorg directive, ARM: ARM Directives. (line 143) +* .ltorg directive, s390: s390 Directives. (line 88) +* .m32r directive, M32R: M32R-Directives. (line 66) +* .m32r2 directive, M32R2: M32R-Directives. (line 77) +* .m32rx directive, M32RX: M32R-Directives. (line 72) +* .movsp directive, ARM: ARM Directives. (line 157) +* .o: Object. (line 6) +* .object_arch directive, ARM: ARM Directives. (line 162) +* .packed directive, ARM: ARM Directives. (line 168) +* .pad directive, ARM: ARM Directives. (line 25) +* .param on HPPA: HPPA Directives. (line 19) +* .personality directive, ARM: ARM Directives. (line 178) +* .personalityindex directive, ARM: ARM Directives. (line 181) +* .pool directive, ARM: ARM Directives. (line 185) +* .quad directive, s390: s390 Directives. (line 16) +* .req directive, ARM: ARM Directives. (line 188) +* .save directive, ARM: ARM Directives. (line 193) +* .secrel32 directive, ARM: ARM Directives. (line 231) +* .set arch=CPU: MIPS ISA. (line 18) +* .set autoextend: MIPS autoextend. (line 6) +* .set doublefloat: MIPS floating-point. (line 12) +* .set dsp: MIPS ASE instruction generation overrides. + (line 21) +* .set dspr2: MIPS ASE instruction generation overrides. + (line 26) +* .set hardfloat: MIPS floating-point. (line 6) +* .set mdmx: MIPS ASE instruction generation overrides. + (line 16) +* .set mips3d: MIPS ASE instruction generation overrides. + (line 6) +* .set mipsN: MIPS ISA. (line 6) +* .set mt: MIPS ASE instruction generation overrides. + (line 32) +* .set noautoextend: MIPS autoextend. (line 6) +* .set nodsp: MIPS ASE instruction generation overrides. + (line 21) +* .set nodspr2: MIPS ASE instruction generation overrides. + (line 26) +* .set nomdmx: MIPS ASE instruction generation overrides. + (line 16) +* .set nomips3d: MIPS ASE instruction generation overrides. + (line 6) +* .set nomt: MIPS ASE instruction generation overrides. + (line 32) +* .set nosmartmips: MIPS ASE instruction generation overrides. + (line 11) +* .set nosym32: MIPS symbol sizes. (line 6) +* .set pop: MIPS option stack. (line 6) +* .set push: MIPS option stack. (line 6) +* .set singlefloat: MIPS floating-point. (line 12) +* .set smartmips: MIPS ASE instruction generation overrides. + (line 11) +* .set softfloat: MIPS floating-point. (line 6) +* .set sym32: MIPS symbol sizes. (line 6) +* .setfp directive, ARM: ARM Directives. (line 217) +* .short directive, s390: s390 Directives. (line 16) +* .syntax directive, ARM: ARM Directives. (line 236) +* .thumb directive, ARM: ARM Directives. (line 240) +* .thumb_func directive, ARM: ARM Directives. (line 243) +* .thumb_set directive, ARM: ARM Directives. (line 254) +* .unreq directive, ARM: ARM Directives. (line 261) +* .unwind_raw directive, ARM: ARM Directives. (line 272) +* .v850 directive, V850: V850 Directives. (line 14) +* .v850e directive, V850: V850 Directives. (line 20) +* .v850e1 directive, V850: V850 Directives. (line 26) +* .vsave directive, ARM: ARM Directives. (line 279) +* .z8001: Z8000 Directives. (line 11) +* .z8002: Z8000 Directives. (line 15) +* 16-bit code, i386: i386-16bit. (line 6) +* 2byte directive, ARC: ARC Directives. (line 9) +* 3byte directive, ARC: ARC Directives. (line 12) +* 3DNow!, i386: i386-SIMD. (line 6) +* 3DNow!, x86-64: i386-SIMD. (line 6) +* 430 support: MSP430-Dependent. (line 6) +* 4byte directive, ARC: ARC Directives. (line 15) +* : (label): Statements. (line 30) +* @word modifier, D10V: D10V-Word. (line 6) +* \" (doublequote character): Strings. (line 43) +* \\ (\ character): Strings. (line 40) +* \b (backspace character): Strings. (line 15) +* \DDD (octal character code): Strings. (line 30) +* \f (formfeed character): Strings. (line 18) +* \n (newline character): Strings. (line 21) +* \r (carriage return character): Strings. (line 24) +* \t (tab): Strings. (line 27) +* \XD... (hex character code): Strings. (line 36) +* _ opcode prefix: Xtensa Opcodes. (line 9) +* a.out: Object. (line 6) +* a.out symbol attributes: a.out Symbols. (line 6) +* A_DIR environment variable, TIC54X: TIC54X-Env. (line 6) +* ABI options, SH64: SH64 Options. (line 29) +* abort directive: Abort. (line 6) +* ABORT directive: ABORT (COFF). (line 6) +* absolute section: Ld Sections. (line 29) +* absolute-literals directive: Absolute Literals Directive. + (line 6) +* ADDI instructions, relaxation: Xtensa Immediate Relaxation. + (line 43) +* addition, permitted arguments: Infix Ops. (line 44) +* addresses: Expressions. (line 6) +* addresses, format of: Secs Background. (line 68) +* addressing modes, D10V: D10V-Addressing. (line 6) +* addressing modes, D30V: D30V-Addressing. (line 6) +* addressing modes, H8/300: H8/300-Addressing. (line 6) +* addressing modes, M680x0: M68K-Syntax. (line 21) +* addressing modes, M68HC11: M68HC11-Syntax. (line 17) +* addressing modes, SH: SH-Addressing. (line 6) +* addressing modes, SH64: SH64-Addressing. (line 6) +* addressing modes, Z8000: Z8000-Addressing. (line 6) +* ADR reg,<label> pseudo op, ARM: ARM Opcodes. (line 25) +* ADRL reg,<label> pseudo op, ARM: ARM Opcodes. (line 35) +* advancing location counter: Org. (line 6) +* align directive: Align. (line 6) +* align directive, SPARC: Sparc-Directives. (line 9) +* align directive, TIC54X: TIC54X-Directives. (line 6) +* alignment of branch targets: Xtensa Automatic Alignment. + (line 6) +* alignment of LOOP instructions: Xtensa Automatic Alignment. + (line 6) +* Alpha floating point (IEEE): Alpha Floating Point. + (line 6) +* Alpha line comment character: Alpha-Chars. (line 6) +* Alpha line separator: Alpha-Chars. (line 8) +* Alpha notes: Alpha Notes. (line 6) +* Alpha options: Alpha Options. (line 6) +* Alpha registers: Alpha-Regs. (line 6) +* Alpha relocations: Alpha-Relocs. (line 6) +* Alpha support: Alpha-Dependent. (line 6) +* Alpha Syntax: Alpha Options. (line 62) +* Alpha-only directives: Alpha Directives. (line 10) +* altered difference tables: Word. (line 12) +* alternate syntax for the 680x0: M68K-Moto-Syntax. (line 6) +* ARC floating point (IEEE): ARC Floating Point. (line 6) +* ARC machine directives: ARC Directives. (line 6) +* ARC opcodes: ARC Opcodes. (line 6) +* ARC options (none): ARC Options. (line 6) +* ARC register names: ARC-Regs. (line 6) +* ARC special characters: ARC-Chars. (line 6) +* ARC support: ARC-Dependent. (line 6) +* arc5 arc5, ARC: ARC Options. (line 10) +* arc6 arc6, ARC: ARC Options. (line 13) +* arc7 arc7, ARC: ARC Options. (line 21) +* arc8 arc8, ARC: ARC Options. (line 24) +* arch directive, i386: i386-Arch. (line 6) +* arch directive, M680x0: M68K-Directives. (line 22) +* arch directive, x86-64: i386-Arch. (line 6) +* architecture options, i960: Options-i960. (line 6) +* architecture options, IP2022: IP2K-Opts. (line 9) +* architecture options, IP2K: IP2K-Opts. (line 14) +* architecture options, M16C: M32C-Opts. (line 12) +* architecture options, M32C: M32C-Opts. (line 9) +* architecture options, M32R: M32R-Opts. (line 21) +* architecture options, M32R2: M32R-Opts. (line 17) +* architecture options, M32RX: M32R-Opts. (line 9) +* architecture options, M680x0: M68K-Opts. (line 104) +* Architecture variant option, CRIS: CRIS-Opts. (line 33) +* architectures, PowerPC: PowerPC-Opts. (line 6) +* architectures, SCORE: SCORE-Opts. (line 6) +* architectures, SPARC: Sparc-Opts. (line 6) +* arguments for addition: Infix Ops. (line 44) +* arguments for subtraction: Infix Ops. (line 49) +* arguments in expressions: Arguments. (line 6) +* arithmetic functions: Operators. (line 6) +* arithmetic operands: Arguments. (line 6) +* ARM data relocations: ARM-Relocations. (line 6) +* ARM floating point (IEEE): ARM Floating Point. (line 6) +* ARM identifiers: ARM-Chars. (line 15) +* ARM immediate character: ARM-Chars. (line 13) +* ARM line comment character: ARM-Chars. (line 6) +* ARM line separator: ARM-Chars. (line 10) +* ARM machine directives: ARM Directives. (line 6) +* ARM opcodes: ARM Opcodes. (line 6) +* ARM options (none): ARM Options. (line 6) +* ARM register names: ARM-Regs. (line 6) +* ARM support: ARM-Dependent. (line 6) +* ascii directive: Ascii. (line 6) +* asciz directive: Asciz. (line 6) +* asg directive, TIC54X: TIC54X-Directives. (line 20) +* assembler bugs, reporting: Bug Reporting. (line 6) +* assembler crash: Bug Criteria. (line 9) +* assembler directive .arch, CRIS: CRIS-Pseudos. (line 45) +* assembler directive .dword, CRIS: CRIS-Pseudos. (line 12) +* assembler directive .far, M68HC11: M68HC11-Directives. (line 20) +* assembler directive .interrupt, M68HC11: M68HC11-Directives. + (line 26) +* assembler directive .mode, M68HC11: M68HC11-Directives. (line 16) +* assembler directive .relax, M68HC11: M68HC11-Directives. (line 10) +* assembler directive .syntax, CRIS: CRIS-Pseudos. (line 17) +* assembler directive .xrefb, M68HC11: M68HC11-Directives. (line 31) +* assembler directive BSPEC, MMIX: MMIX-Pseudos. (line 131) +* assembler directive BYTE, MMIX: MMIX-Pseudos. (line 97) +* assembler directive ESPEC, MMIX: MMIX-Pseudos. (line 131) +* assembler directive GREG, MMIX: MMIX-Pseudos. (line 50) +* assembler directive IS, MMIX: MMIX-Pseudos. (line 42) +* assembler directive LOC, MMIX: MMIX-Pseudos. (line 7) +* assembler directive LOCAL, MMIX: MMIX-Pseudos. (line 28) +* assembler directive OCTA, MMIX: MMIX-Pseudos. (line 108) +* assembler directive PREFIX, MMIX: MMIX-Pseudos. (line 120) +* assembler directive TETRA, MMIX: MMIX-Pseudos. (line 108) +* assembler directive WYDE, MMIX: MMIX-Pseudos. (line 108) +* assembler directives, CRIS: CRIS-Pseudos. (line 6) +* assembler directives, M68HC11: M68HC11-Directives. (line 6) +* assembler directives, M68HC12: M68HC11-Directives. (line 6) +* assembler directives, MMIX: MMIX-Pseudos. (line 6) +* assembler internal logic error: As Sections. (line 13) +* assembler version: v. (line 6) +* assembler, and linker: Secs Background. (line 10) +* assembly listings, enabling: a. (line 6) +* assigning values to symbols <1>: Setting Symbols. (line 6) +* assigning values to symbols: Equ. (line 6) +* atmp directive, i860: Directives-i860. (line 16) +* att_syntax pseudo op, i386: i386-Syntax. (line 6) +* att_syntax pseudo op, x86-64: i386-Syntax. (line 6) +* attributes, symbol: Symbol Attributes. (line 6) +* auxiliary attributes, COFF symbols: COFF Symbols. (line 19) +* auxiliary symbol information, COFF: Dim. (line 6) +* Av7: Sparc-Opts. (line 25) +* AVR line comment character: AVR-Chars. (line 6) +* AVR line separator: AVR-Chars. (line 10) +* AVR modifiers: AVR-Modifiers. (line 6) +* AVR opcode summary: AVR Opcodes. (line 6) +* AVR options (none): AVR Options. (line 6) +* AVR register names: AVR-Regs. (line 6) +* AVR support: AVR-Dependent. (line 6) +* backslash (\\): Strings. (line 40) +* backspace (\b): Strings. (line 15) +* balign directive: Balign. (line 6) +* balignl directive: Balign. (line 27) +* balignw directive: Balign. (line 27) +* bes directive, TIC54X: TIC54X-Directives. (line 197) +* big endian output, MIPS: Overview. (line 641) +* big endian output, PJ: Overview. (line 548) +* big-endian output, MIPS: MIPS Opts. (line 13) +* bignums: Bignums. (line 6) +* binary constants, TIC54X: TIC54X-Constants. (line 8) +* binary files, including: Incbin. (line 6) +* binary integers: Integers. (line 6) +* bit names, IA-64: IA-64-Bits. (line 6) +* bitfields, not supported on VAX: VAX-no. (line 6) +* Blackfin directives: Blackfin Directives. (line 6) +* Blackfin options (none): Blackfin Options. (line 6) +* Blackfin support: Blackfin-Dependent. (line 6) +* Blackfin syntax: Blackfin Syntax. (line 6) +* block: Z8000 Directives. (line 55) +* branch improvement, M680x0: M68K-Branch. (line 6) +* branch improvement, M68HC11: M68HC11-Branch. (line 6) +* branch improvement, VAX: VAX-branch. (line 6) +* branch instructions, relaxation: Xtensa Branch Relaxation. + (line 6) +* branch recording, i960: Options-i960. (line 22) +* branch statistics table, i960: Options-i960. (line 40) +* branch target alignment: Xtensa Automatic Alignment. + (line 6) +* break directive, TIC54X: TIC54X-Directives. (line 143) +* BSD syntax: PDP-11-Syntax. (line 6) +* bss directive, i960: Directives-i960. (line 6) +* bss directive, TIC54X: TIC54X-Directives. (line 29) +* bss section <1>: bss. (line 6) +* bss section: Ld Sections. (line 20) +* bug criteria: Bug Criteria. (line 6) +* bug reports: Bug Reporting. (line 6) +* bugs in assembler: Reporting Bugs. (line 6) +* Built-in symbols, CRIS: CRIS-Symbols. (line 6) +* builtin math functions, TIC54X: TIC54X-Builtins. (line 6) +* builtin subsym functions, TIC54X: TIC54X-Macros. (line 16) +* bus lock prefixes, i386: i386-Prefixes. (line 36) +* bval: Z8000 Directives. (line 30) +* byte directive: Byte. (line 6) +* byte directive, TIC54X: TIC54X-Directives. (line 36) +* C54XDSP_DIR environment variable, TIC54X: TIC54X-Env. (line 6) +* c_mode directive, TIC54X: TIC54X-Directives. (line 51) +* call instructions, i386: i386-Mnemonics. (line 55) +* call instructions, relaxation: Xtensa Call Relaxation. + (line 6) +* call instructions, x86-64: i386-Mnemonics. (line 55) +* callj, i960 pseudo-opcode: callj-i960. (line 6) +* carriage return (\r): Strings. (line 24) +* case sensitivity, Z80: Z80-Case. (line 6) +* cfi_endproc directive: CFI directives. (line 26) +* cfi_sections directive: CFI directives. (line 13) +* cfi_startproc directive: CFI directives. (line 6) +* char directive, TIC54X: TIC54X-Directives. (line 36) +* character constant, Z80: Z80-Chars. (line 13) +* character constants: Characters. (line 6) +* character escape codes: Strings. (line 15) +* character escapes, Z80: Z80-Chars. (line 11) +* character, single: Chars. (line 6) +* characters used in symbols: Symbol Intro. (line 6) +* clink directive, TIC54X: TIC54X-Directives. (line 45) +* code16 directive, i386: i386-16bit. (line 6) +* code16gcc directive, i386: i386-16bit. (line 6) +* code32 directive, i386: i386-16bit. (line 6) +* code64 directive, i386: i386-16bit. (line 6) +* code64 directive, x86-64: i386-16bit. (line 6) +* COFF auxiliary symbol information: Dim. (line 6) +* COFF structure debugging: Tag. (line 6) +* COFF symbol attributes: COFF Symbols. (line 6) +* COFF symbol descriptor: Desc. (line 6) +* COFF symbol storage class: Scl. (line 6) +* COFF symbol type: Type. (line 11) +* COFF symbols, debugging: Def. (line 6) +* COFF value attribute: Val. (line 6) +* COMDAT: Linkonce. (line 6) +* comm directive: Comm. (line 6) +* command line conventions: Command Line. (line 6) +* command line options, V850: V850 Options. (line 9) +* command-line options ignored, VAX: VAX-Opts. (line 6) +* comments: Comments. (line 6) +* comments, M680x0: M68K-Chars. (line 6) +* comments, removed by preprocessor: Preprocessing. (line 11) +* common directive, SPARC: Sparc-Directives. (line 12) +* common sections: Linkonce. (line 6) +* common variable storage: bss. (line 6) +* compare and jump expansions, i960: Compare-and-branch-i960. + (line 13) +* compare/branch instructions, i960: Compare-and-branch-i960. + (line 6) +* comparison expressions: Infix Ops. (line 55) +* conditional assembly: If. (line 6) +* constant, single character: Chars. (line 6) +* constants: Constants. (line 6) +* constants, bignum: Bignums. (line 6) +* constants, character: Characters. (line 6) +* constants, converted by preprocessor: Preprocessing. (line 14) +* constants, floating point: Flonums. (line 6) +* constants, integer: Integers. (line 6) +* constants, number: Numbers. (line 6) +* constants, Sparc: Sparc-Constants. (line 6) +* constants, string: Strings. (line 6) +* constants, TIC54X: TIC54X-Constants. (line 6) +* conversion instructions, i386: i386-Mnemonics. (line 36) +* conversion instructions, x86-64: i386-Mnemonics. (line 36) +* coprocessor wait, i386: i386-Prefixes. (line 40) +* copy directive, TIC54X: TIC54X-Directives. (line 54) +* cpu directive, M680x0: M68K-Directives. (line 30) +* CR16 Operand Qualifiers: CR16 Operand Qualifiers. + (line 6) +* CR16 support: CR16-Dependent. (line 6) +* crash of assembler: Bug Criteria. (line 9) +* CRIS --emulation=crisaout command line option: CRIS-Opts. (line 9) +* CRIS --emulation=criself command line option: CRIS-Opts. (line 9) +* CRIS --march=ARCHITECTURE command line option: CRIS-Opts. (line 33) +* CRIS --mul-bug-abort command line option: CRIS-Opts. (line 61) +* CRIS --no-mul-bug-abort command line option: CRIS-Opts. (line 61) +* CRIS --no-underscore command line option: CRIS-Opts. (line 15) +* CRIS --pic command line option: CRIS-Opts. (line 27) +* CRIS --underscore command line option: CRIS-Opts. (line 15) +* CRIS -N command line option: CRIS-Opts. (line 57) +* CRIS architecture variant option: CRIS-Opts. (line 33) +* CRIS assembler directive .arch: CRIS-Pseudos. (line 45) +* CRIS assembler directive .dword: CRIS-Pseudos. (line 12) +* CRIS assembler directive .syntax: CRIS-Pseudos. (line 17) +* CRIS assembler directives: CRIS-Pseudos. (line 6) +* CRIS built-in symbols: CRIS-Symbols. (line 6) +* CRIS instruction expansion: CRIS-Expand. (line 6) +* CRIS line comment characters: CRIS-Chars. (line 6) +* CRIS options: CRIS-Opts. (line 6) +* CRIS position-independent code: CRIS-Opts. (line 27) +* CRIS pseudo-op .arch: CRIS-Pseudos. (line 45) +* CRIS pseudo-op .dword: CRIS-Pseudos. (line 12) +* CRIS pseudo-op .syntax: CRIS-Pseudos. (line 17) +* CRIS pseudo-ops: CRIS-Pseudos. (line 6) +* CRIS register names: CRIS-Regs. (line 6) +* CRIS support: CRIS-Dependent. (line 6) +* CRIS symbols in position-independent code: CRIS-Pic. (line 6) +* ctbp register, V850: V850-Regs. (line 131) +* ctoff pseudo-op, V850: V850 Opcodes. (line 111) +* ctpc register, V850: V850-Regs. (line 119) +* ctpsw register, V850: V850-Regs. (line 122) +* current address: Dot. (line 6) +* current address, advancing: Org. (line 6) +* D10V @word modifier: D10V-Word. (line 6) +* D10V addressing modes: D10V-Addressing. (line 6) +* D10V floating point: D10V-Float. (line 6) +* D10V line comment character: D10V-Chars. (line 6) +* D10V opcode summary: D10V-Opcodes. (line 6) +* D10V optimization: Overview. (line 420) +* D10V options: D10V-Opts. (line 6) +* D10V registers: D10V-Regs. (line 6) +* D10V size modifiers: D10V-Size. (line 6) +* D10V sub-instruction ordering: D10V-Chars. (line 6) +* D10V sub-instructions: D10V-Subs. (line 6) +* D10V support: D10V-Dependent. (line 6) +* D10V syntax: D10V-Syntax. (line 6) +* D30V addressing modes: D30V-Addressing. (line 6) +* D30V floating point: D30V-Float. (line 6) +* D30V Guarded Execution: D30V-Guarded. (line 6) +* D30V line comment character: D30V-Chars. (line 6) +* D30V nops: Overview. (line 428) +* D30V nops after 32-bit multiply: Overview. (line 431) +* D30V opcode summary: D30V-Opcodes. (line 6) +* D30V optimization: Overview. (line 425) +* D30V options: D30V-Opts. (line 6) +* D30V registers: D30V-Regs. (line 6) +* D30V size modifiers: D30V-Size. (line 6) +* D30V sub-instruction ordering: D30V-Chars. (line 6) +* D30V sub-instructions: D30V-Subs. (line 6) +* D30V support: D30V-Dependent. (line 6) +* D30V syntax: D30V-Syntax. (line 6) +* data alignment on SPARC: Sparc-Aligned-Data. (line 6) +* data and text sections, joining: R. (line 6) +* data directive: Data. (line 6) +* data directive, TIC54X: TIC54X-Directives. (line 61) +* data relocations, ARM: ARM-Relocations. (line 6) +* data section: Ld Sections. (line 9) +* data1 directive, M680x0: M68K-Directives. (line 9) +* data2 directive, M680x0: M68K-Directives. (line 12) +* datalabel, SH64: SH64-Addressing. (line 16) +* dbpc register, V850: V850-Regs. (line 125) +* dbpsw register, V850: V850-Regs. (line 128) +* debuggers, and symbol order: Symbols. (line 10) +* debugging COFF symbols: Def. (line 6) +* DEC syntax: PDP-11-Syntax. (line 6) +* decimal integers: Integers. (line 12) +* def directive: Def. (line 6) +* def directive, TIC54X: TIC54X-Directives. (line 103) +* density instructions: Density Instructions. + (line 6) +* dependency tracking: MD. (line 6) +* deprecated directives: Deprecated. (line 6) +* desc directive: Desc. (line 6) +* descriptor, of a.out symbol: Symbol Desc. (line 6) +* dfloat directive, VAX: VAX-directives. (line 10) +* difference tables altered: Word. (line 12) +* difference tables, warning: K. (line 6) +* differences, mmixal: MMIX-mmixal. (line 6) +* dim directive: Dim. (line 6) +* directives and instructions: Statements. (line 19) +* directives for PowerPC: PowerPC-Pseudo. (line 6) +* directives for SCORE: SCORE-Pseudo. (line 6) +* directives, Blackfin: Blackfin Directives. (line 6) +* directives, M32R: M32R-Directives. (line 6) +* directives, M680x0: M68K-Directives. (line 6) +* directives, machine independent: Pseudo Ops. (line 6) +* directives, Xtensa: Xtensa Directives. (line 6) +* directives, Z8000: Z8000 Directives. (line 6) +* Disable floating-point instructions: MIPS floating-point. (line 6) +* Disable single-precision floating-point operations: MIPS floating-point. + (line 12) +* displacement sizing character, VAX: VAX-operands. (line 12) +* dollar local symbols: Symbol Names. (line 105) +* dot (symbol): Dot. (line 6) +* double directive: Double. (line 6) +* double directive, i386: i386-Float. (line 14) +* double directive, M680x0: M68K-Float. (line 14) +* double directive, M68HC11: M68HC11-Float. (line 14) +* double directive, TIC54X: TIC54X-Directives. (line 64) +* double directive, VAX: VAX-float. (line 15) +* double directive, x86-64: i386-Float. (line 14) +* doublequote (\"): Strings. (line 43) +* drlist directive, TIC54X: TIC54X-Directives. (line 73) +* drnolist directive, TIC54X: TIC54X-Directives. (line 73) +* dual directive, i860: Directives-i860. (line 6) +* ECOFF sections: MIPS Object. (line 6) +* ecr register, V850: V850-Regs. (line 113) +* eight-byte integer: Quad. (line 9) +* eipc register, V850: V850-Regs. (line 101) +* eipsw register, V850: V850-Regs. (line 104) +* eject directive: Eject. (line 6) +* ELF symbol type: Type. (line 22) +* else directive: Else. (line 6) +* elseif directive: Elseif. (line 6) +* empty expressions: Empty Exprs. (line 6) +* emsg directive, TIC54X: TIC54X-Directives. (line 77) +* emulation: Overview. (line 744) +* encoding options, i386: i386-Mnemonics. (line 32) +* encoding options, x86-64: i386-Mnemonics. (line 32) +* end directive: End. (line 6) +* enddual directive, i860: Directives-i860. (line 11) +* endef directive: Endef. (line 6) +* endfunc directive: Endfunc. (line 6) +* endianness, MIPS: Overview. (line 641) +* endianness, PJ: Overview. (line 548) +* endif directive: Endif. (line 6) +* endloop directive, TIC54X: TIC54X-Directives. (line 143) +* endm directive: Macro. (line 138) +* endm directive, TIC54X: TIC54X-Directives. (line 153) +* endstruct directive, TIC54X: TIC54X-Directives. (line 217) +* endunion directive, TIC54X: TIC54X-Directives. (line 251) +* environment settings, TIC54X: TIC54X-Env. (line 6) +* EOF, newline must precede: Statements. (line 13) +* ep register, V850: V850-Regs. (line 95) +* equ directive: Equ. (line 6) +* equ directive, TIC54X: TIC54X-Directives. (line 192) +* equiv directive: Equiv. (line 6) +* eqv directive: Eqv. (line 6) +* err directive: Err. (line 6) +* error directive: Error. (line 6) +* error messages: Errors. (line 6) +* error on valid input: Bug Criteria. (line 12) +* errors, caused by warnings: W. (line 16) +* errors, continuing after: Z. (line 6) +* ESA/390 floating point (IEEE): ESA/390 Floating Point. + (line 6) +* ESA/390 support: ESA/390-Dependent. (line 6) +* ESA/390 Syntax: ESA/390 Options. (line 8) +* ESA/390-only directives: ESA/390 Directives. (line 12) +* escape codes, character: Strings. (line 15) +* eval directive, TIC54X: TIC54X-Directives. (line 24) +* even: Z8000 Directives. (line 58) +* even directive, M680x0: M68K-Directives. (line 15) +* even directive, TIC54X: TIC54X-Directives. (line 6) +* exitm directive: Macro. (line 141) +* expr (internal section): As Sections. (line 17) +* expression arguments: Arguments. (line 6) +* expressions: Expressions. (line 6) +* expressions, comparison: Infix Ops. (line 55) +* expressions, empty: Empty Exprs. (line 6) +* expressions, integer: Integer Exprs. (line 6) +* extAuxRegister directive, ARC: ARC Directives. (line 18) +* extCondCode directive, ARC: ARC Directives. (line 41) +* extCoreRegister directive, ARC: ARC Directives. (line 53) +* extend directive M680x0: M68K-Float. (line 17) +* extend directive M68HC11: M68HC11-Float. (line 17) +* extended directive, i960: Directives-i960. (line 13) +* extern directive: Extern. (line 6) +* extInstruction directive, ARC: ARC Directives. (line 78) +* fail directive: Fail. (line 6) +* far_mode directive, TIC54X: TIC54X-Directives. (line 82) +* faster processing (-f): f. (line 6) +* fatal signal: Bug Criteria. (line 9) +* fclist directive, TIC54X: TIC54X-Directives. (line 87) +* fcnolist directive, TIC54X: TIC54X-Directives. (line 87) +* fepc register, V850: V850-Regs. (line 107) +* fepsw register, V850: V850-Regs. (line 110) +* ffloat directive, VAX: VAX-directives. (line 14) +* field directive, TIC54X: TIC54X-Directives. (line 91) +* file directive: File. (line 6) +* file directive, MSP 430: MSP430 Directives. (line 6) +* file name, logical: File. (line 13) +* files, including: Include. (line 6) +* files, input: Input Files. (line 6) +* fill directive: Fill. (line 6) +* filling memory <1>: Skip. (line 6) +* filling memory: Space. (line 6) +* FLIX syntax: Xtensa Syntax. (line 6) +* float directive: Float. (line 6) +* float directive, i386: i386-Float. (line 14) +* float directive, M680x0: M68K-Float. (line 11) +* float directive, M68HC11: M68HC11-Float. (line 11) +* float directive, TIC54X: TIC54X-Directives. (line 64) +* float directive, VAX: VAX-float. (line 15) +* float directive, x86-64: i386-Float. (line 14) +* floating point numbers: Flonums. (line 6) +* floating point numbers (double): Double. (line 6) +* floating point numbers (single) <1>: Float. (line 6) +* floating point numbers (single): Single. (line 6) +* floating point, Alpha (IEEE): Alpha Floating Point. + (line 6) +* floating point, ARC (IEEE): ARC Floating Point. (line 6) +* floating point, ARM (IEEE): ARM Floating Point. (line 6) +* floating point, D10V: D10V-Float. (line 6) +* floating point, D30V: D30V-Float. (line 6) +* floating point, ESA/390 (IEEE): ESA/390 Floating Point. + (line 6) +* floating point, H8/300 (IEEE): H8/300 Floating Point. + (line 6) +* floating point, HPPA (IEEE): HPPA Floating Point. (line 6) +* floating point, i386: i386-Float. (line 6) +* floating point, i960 (IEEE): Floating Point-i960. (line 6) +* floating point, M680x0: M68K-Float. (line 6) +* floating point, M68HC11: M68HC11-Float. (line 6) +* floating point, MSP 430 (IEEE): MSP430 Floating Point. + (line 6) +* floating point, s390: s390 Floating Point. (line 6) +* floating point, SH (IEEE): SH Floating Point. (line 6) +* floating point, SPARC (IEEE): Sparc-Float. (line 6) +* floating point, V850 (IEEE): V850 Floating Point. (line 6) +* floating point, VAX: VAX-float. (line 6) +* floating point, x86-64: i386-Float. (line 6) +* floating point, Z80: Z80 Floating Point. (line 6) +* flonums: Flonums. (line 6) +* format of error messages: Errors. (line 24) +* format of warning messages: Errors. (line 12) +* formfeed (\f): Strings. (line 18) +* func directive: Func. (line 6) +* functions, in expressions: Operators. (line 6) +* gbr960, i960 postprocessor: Options-i960. (line 40) +* gfloat directive, VAX: VAX-directives. (line 18) +* global: Z8000 Directives. (line 21) +* global directive: Global. (line 6) +* global directive, TIC54X: TIC54X-Directives. (line 103) +* gp register, MIPS: MIPS Object. (line 11) +* gp register, V850: V850-Regs. (line 17) +* grouping data: Sub-Sections. (line 6) +* H8/300 addressing modes: H8/300-Addressing. (line 6) +* H8/300 floating point (IEEE): H8/300 Floating Point. + (line 6) +* H8/300 line comment character: H8/300-Chars. (line 6) +* H8/300 line separator: H8/300-Chars. (line 8) +* H8/300 machine directives (none): H8/300 Directives. (line 6) +* H8/300 opcode summary: H8/300 Opcodes. (line 6) +* H8/300 options: H8/300 Options. (line 6) +* H8/300 registers: H8/300-Regs. (line 6) +* H8/300 size suffixes: H8/300 Opcodes. (line 163) +* H8/300 support: H8/300-Dependent. (line 6) +* H8/300H, assembling for: H8/300 Directives. (line 8) +* half directive, ARC: ARC Directives. (line 156) +* half directive, SPARC: Sparc-Directives. (line 17) +* half directive, TIC54X: TIC54X-Directives. (line 111) +* hex character code (\XD...): Strings. (line 36) +* hexadecimal integers: Integers. (line 15) +* hexadecimal prefix, Z80: Z80-Chars. (line 8) +* hfloat directive, VAX: VAX-directives. (line 22) +* hi pseudo-op, V850: V850 Opcodes. (line 33) +* hi0 pseudo-op, V850: V850 Opcodes. (line 10) +* hidden directive: Hidden. (line 6) +* high directive, M32R: M32R-Directives. (line 18) +* hilo pseudo-op, V850: V850 Opcodes. (line 55) +* HPPA directives not supported: HPPA Directives. (line 11) +* HPPA floating point (IEEE): HPPA Floating Point. (line 6) +* HPPA Syntax: HPPA Options. (line 8) +* HPPA-only directives: HPPA Directives. (line 24) +* hword directive: hword. (line 6) +* i370 support: ESA/390-Dependent. (line 6) +* i386 16-bit code: i386-16bit. (line 6) +* i386 arch directive: i386-Arch. (line 6) +* i386 att_syntax pseudo op: i386-Syntax. (line 6) +* i386 conversion instructions: i386-Mnemonics. (line 36) +* i386 floating point: i386-Float. (line 6) +* i386 immediate operands: i386-Syntax. (line 15) +* i386 instruction naming: i386-Mnemonics. (line 6) +* i386 instruction prefixes: i386-Prefixes. (line 6) +* i386 intel_syntax pseudo op: i386-Syntax. (line 6) +* i386 jump optimization: i386-Jumps. (line 6) +* i386 jump, call, return: i386-Syntax. (line 38) +* i386 jump/call operands: i386-Syntax. (line 15) +* i386 memory references: i386-Memory. (line 6) +* i386 mnemonic compatibility: i386-Mnemonics. (line 61) +* i386 mul, imul instructions: i386-Notes. (line 6) +* i386 options: i386-Options. (line 6) +* i386 register operands: i386-Syntax. (line 15) +* i386 registers: i386-Regs. (line 6) +* i386 sections: i386-Syntax. (line 44) +* i386 size suffixes: i386-Syntax. (line 29) +* i386 source, destination operands: i386-Syntax. (line 22) +* i386 support: i386-Dependent. (line 6) +* i386 syntax compatibility: i386-Syntax. (line 6) +* i80386 support: i386-Dependent. (line 6) +* i860 machine directives: Directives-i860. (line 6) +* i860 opcodes: Opcodes for i860. (line 6) +* i860 support: i860-Dependent. (line 6) +* i960 architecture options: Options-i960. (line 6) +* i960 branch recording: Options-i960. (line 22) +* i960 callj pseudo-opcode: callj-i960. (line 6) +* i960 compare and jump expansions: Compare-and-branch-i960. + (line 13) +* i960 compare/branch instructions: Compare-and-branch-i960. + (line 6) +* i960 floating point (IEEE): Floating Point-i960. (line 6) +* i960 machine directives: Directives-i960. (line 6) +* i960 opcodes: Opcodes for i960. (line 6) +* i960 options: Options-i960. (line 6) +* i960 support: i960-Dependent. (line 6) +* IA-64 line comment character: IA-64-Chars. (line 6) +* IA-64 line separator: IA-64-Chars. (line 8) +* IA-64 options: IA-64 Options. (line 6) +* IA-64 Processor-status-Register bit names: IA-64-Bits. (line 6) +* IA-64 registers: IA-64-Regs. (line 6) +* IA-64 support: IA-64-Dependent. (line 6) +* IA-64 Syntax: IA-64 Options. (line 96) +* ident directive: Ident. (line 6) +* identifiers, ARM: ARM-Chars. (line 15) +* identifiers, MSP 430: MSP430-Chars. (line 8) +* if directive: If. (line 6) +* ifb directive: If. (line 21) +* ifc directive: If. (line 25) +* ifdef directive: If. (line 16) +* ifeq directive: If. (line 33) +* ifeqs directive: If. (line 36) +* ifge directive: If. (line 40) +* ifgt directive: If. (line 44) +* ifle directive: If. (line 48) +* iflt directive: If. (line 52) +* ifnb directive: If. (line 56) +* ifnc directive: If. (line 61) +* ifndef directive: If. (line 65) +* ifne directive: If. (line 72) +* ifnes directive: If. (line 76) +* ifnotdef directive: If. (line 65) +* immediate character, ARM: ARM-Chars. (line 13) +* immediate character, M680x0: M68K-Chars. (line 6) +* immediate character, VAX: VAX-operands. (line 6) +* immediate fields, relaxation: Xtensa Immediate Relaxation. + (line 6) +* immediate operands, i386: i386-Syntax. (line 15) +* immediate operands, x86-64: i386-Syntax. (line 15) +* imul instruction, i386: i386-Notes. (line 6) +* imul instruction, x86-64: i386-Notes. (line 6) +* incbin directive: Incbin. (line 6) +* include directive: Include. (line 6) +* include directive search path: I. (line 6) +* indirect character, VAX: VAX-operands. (line 9) +* infix operators: Infix Ops. (line 6) +* inhibiting interrupts, i386: i386-Prefixes. (line 36) +* input: Input Files. (line 6) +* input file linenumbers: Input Files. (line 35) +* instruction aliases, s390: s390 Aliases. (line 6) +* instruction expansion, CRIS: CRIS-Expand. (line 6) +* instruction expansion, MMIX: MMIX-Expand. (line 6) +* instruction formats, s390: s390 Formats. (line 6) +* instruction marker, s390: s390 Instruction Marker. + (line 6) +* instruction mnemonics, s390: s390 Mnemonics. (line 6) +* instruction naming, i386: i386-Mnemonics. (line 6) +* instruction naming, x86-64: i386-Mnemonics. (line 6) +* instruction operand modifier, s390: s390 Operand Modifier. + (line 6) +* instruction operands, s390: s390 Operands. (line 6) +* instruction prefixes, i386: i386-Prefixes. (line 6) +* instruction set, M680x0: M68K-opcodes. (line 6) +* instruction set, M68HC11: M68HC11-opcodes. (line 6) +* instruction summary, AVR: AVR Opcodes. (line 6) +* instruction summary, D10V: D10V-Opcodes. (line 6) +* instruction summary, D30V: D30V-Opcodes. (line 6) +* instruction summary, H8/300: H8/300 Opcodes. (line 6) +* instruction summary, LM32: LM32 Opcodes. (line 6) +* instruction summary, SH: SH Opcodes. (line 6) +* instruction summary, SH64: SH64 Opcodes. (line 6) +* instruction summary, Z8000: Z8000 Opcodes. (line 6) +* instruction syntax, s390: s390 Syntax. (line 6) +* instructions and directives: Statements. (line 19) +* int directive: Int. (line 6) +* int directive, H8/300: H8/300 Directives. (line 6) +* int directive, i386: i386-Float. (line 21) +* int directive, TIC54X: TIC54X-Directives. (line 111) +* int directive, x86-64: i386-Float. (line 21) +* integer expressions: Integer Exprs. (line 6) +* integer, 16-byte: Octa. (line 6) +* integer, 8-byte: Quad. (line 9) +* integers: Integers. (line 6) +* integers, 16-bit: hword. (line 6) +* integers, 32-bit: Int. (line 6) +* integers, binary: Integers. (line 6) +* integers, decimal: Integers. (line 12) +* integers, hexadecimal: Integers. (line 15) +* integers, octal: Integers. (line 9) +* integers, one byte: Byte. (line 6) +* intel_syntax pseudo op, i386: i386-Syntax. (line 6) +* intel_syntax pseudo op, x86-64: i386-Syntax. (line 6) +* internal assembler sections: As Sections. (line 6) +* internal directive: Internal. (line 6) +* invalid input: Bug Criteria. (line 14) +* invocation summary: Overview. (line 6) +* IP2K architecture options: IP2K-Opts. (line 14) +* IP2K options: IP2K-Opts. (line 6) +* IP2K support: IP2K-Dependent. (line 6) +* irp directive: Irp. (line 6) +* irpc directive: Irpc. (line 6) +* ISA options, SH64: SH64 Options. (line 6) +* joining text and data sections: R. (line 6) +* jump instructions, i386: i386-Mnemonics. (line 55) +* jump instructions, x86-64: i386-Mnemonics. (line 55) +* jump optimization, i386: i386-Jumps. (line 6) +* jump optimization, x86-64: i386-Jumps. (line 6) +* jump/call operands, i386: i386-Syntax. (line 15) +* jump/call operands, x86-64: i386-Syntax. (line 15) +* L16SI instructions, relaxation: Xtensa Immediate Relaxation. + (line 23) +* L16UI instructions, relaxation: Xtensa Immediate Relaxation. + (line 23) +* L32I instructions, relaxation: Xtensa Immediate Relaxation. + (line 23) +* L8UI instructions, relaxation: Xtensa Immediate Relaxation. + (line 23) +* label (:): Statements. (line 30) +* label directive, TIC54X: TIC54X-Directives. (line 123) +* labels: Labels. (line 6) +* lcomm directive: Lcomm. (line 6) +* lcomm directive, COFF: i386-Directives. (line 6) +* ld: Object. (line 15) +* ldouble directive M680x0: M68K-Float. (line 17) +* ldouble directive M68HC11: M68HC11-Float. (line 17) +* ldouble directive, TIC54X: TIC54X-Directives. (line 64) +* LDR reg,=<label> pseudo op, ARM: ARM Opcodes. (line 15) +* leafproc directive, i960: Directives-i960. (line 18) +* length directive, TIC54X: TIC54X-Directives. (line 127) +* length of symbols: Symbol Intro. (line 14) +* lflags directive (ignored): Lflags. (line 6) +* line comment character: Comments. (line 19) +* line comment character, Alpha: Alpha-Chars. (line 6) +* line comment character, ARM: ARM-Chars. (line 6) +* line comment character, AVR: AVR-Chars. (line 6) +* line comment character, D10V: D10V-Chars. (line 6) +* line comment character, D30V: D30V-Chars. (line 6) +* line comment character, H8/300: H8/300-Chars. (line 6) +* line comment character, IA-64: IA-64-Chars. (line 6) +* line comment character, M680x0: M68K-Chars. (line 6) +* line comment character, MSP 430: MSP430-Chars. (line 6) +* line comment character, s390: s390 Characters. (line 6) +* line comment character, SH: SH-Chars. (line 6) +* line comment character, SH64: SH64-Chars. (line 6) +* line comment character, Sparc: Sparc-Chars. (line 6) +* line comment character, V850: V850-Chars. (line 6) +* line comment character, Z80: Z80-Chars. (line 6) +* line comment character, Z8000: Z8000-Chars. (line 6) +* line comment characters, CRIS: CRIS-Chars. (line 6) +* line comment characters, MMIX: MMIX-Chars. (line 6) +* line directive: Line. (line 6) +* line directive, MSP 430: MSP430 Directives. (line 14) +* line numbers, in input files: Input Files. (line 35) +* line numbers, in warnings/errors: Errors. (line 16) +* line separator character: Statements. (line 6) +* line separator, Alpha: Alpha-Chars. (line 8) +* line separator, ARM: ARM-Chars. (line 10) +* line separator, AVR: AVR-Chars. (line 10) +* line separator, H8/300: H8/300-Chars. (line 8) +* line separator, IA-64: IA-64-Chars. (line 8) +* line separator, SH: SH-Chars. (line 8) +* line separator, SH64: SH64-Chars. (line 8) +* line separator, Sparc: Sparc-Chars. (line 8) +* line separator, Z8000: Z8000-Chars. (line 8) +* lines starting with #: Comments. (line 39) +* linker: Object. (line 15) +* linker, and assembler: Secs Background. (line 10) +* linkonce directive: Linkonce. (line 6) +* list directive: List. (line 6) +* list directive, TIC54X: TIC54X-Directives. (line 131) +* listing control, turning off: Nolist. (line 6) +* listing control, turning on: List. (line 6) +* listing control: new page: Eject. (line 6) +* listing control: paper size: Psize. (line 6) +* listing control: subtitle: Sbttl. (line 6) +* listing control: title line: Title. (line 6) +* listings, enabling: a. (line 6) +* literal directive: Literal Directive. (line 6) +* literal pool entries, s390: s390 Literal Pool Entries. + (line 6) +* literal_position directive: Literal Position Directive. + (line 6) +* literal_prefix directive: Literal Prefix Directive. + (line 6) +* little endian output, MIPS: Overview. (line 644) +* little endian output, PJ: Overview. (line 551) +* little-endian output, MIPS: MIPS Opts. (line 13) +* LM32 modifiers: LM32-Modifiers. (line 6) +* LM32 opcode summary: LM32 Opcodes. (line 6) +* LM32 options (none): LM32 Options. (line 6) +* LM32 register names: LM32-Regs. (line 6) +* LM32 support: LM32-Dependent. (line 6) +* ln directive: Ln. (line 6) +* lo pseudo-op, V850: V850 Opcodes. (line 22) +* loc directive: Loc. (line 6) +* loc_mark_labels directive: Loc_mark_labels. (line 6) +* local common symbols: Lcomm. (line 6) +* local directive: Local. (line 6) +* local labels: Symbol Names. (line 35) +* local symbol names: Symbol Names. (line 22) +* local symbols, retaining in output: L. (line 6) +* location counter: Dot. (line 6) +* location counter, advancing: Org. (line 6) +* location counter, Z80: Z80-Chars. (line 8) +* logical file name: File. (line 13) +* logical line number: Line. (line 6) +* logical line numbers: Comments. (line 39) +* long directive: Long. (line 6) +* long directive, ARC: ARC Directives. (line 159) +* long directive, i386: i386-Float. (line 21) +* long directive, TIC54X: TIC54X-Directives. (line 135) +* long directive, x86-64: i386-Float. (line 21) +* longcall pseudo-op, V850: V850 Opcodes. (line 123) +* longcalls directive: Longcalls Directive. (line 6) +* longjump pseudo-op, V850: V850 Opcodes. (line 129) +* loop directive, TIC54X: TIC54X-Directives. (line 143) +* LOOP instructions, alignment: Xtensa Automatic Alignment. + (line 6) +* low directive, M32R: M32R-Directives. (line 9) +* lp register, V850: V850-Regs. (line 98) +* lval: Z8000 Directives. (line 27) +* M16C architecture option: M32C-Opts. (line 12) +* M32C architecture option: M32C-Opts. (line 9) +* M32C modifiers: M32C-Modifiers. (line 6) +* M32C options: M32C-Opts. (line 6) +* M32C support: M32C-Dependent. (line 6) +* M32R architecture options: M32R-Opts. (line 9) +* M32R directives: M32R-Directives. (line 6) +* M32R options: M32R-Opts. (line 6) +* M32R support: M32R-Dependent. (line 6) +* M32R warnings: M32R-Warnings. (line 6) +* M680x0 addressing modes: M68K-Syntax. (line 21) +* M680x0 architecture options: M68K-Opts. (line 104) +* M680x0 branch improvement: M68K-Branch. (line 6) +* M680x0 directives: M68K-Directives. (line 6) +* M680x0 floating point: M68K-Float. (line 6) +* M680x0 immediate character: M68K-Chars. (line 6) +* M680x0 line comment character: M68K-Chars. (line 6) +* M680x0 opcodes: M68K-opcodes. (line 6) +* M680x0 options: M68K-Opts. (line 6) +* M680x0 pseudo-opcodes: M68K-Branch. (line 6) +* M680x0 size modifiers: M68K-Syntax. (line 8) +* M680x0 support: M68K-Dependent. (line 6) +* M680x0 syntax: M68K-Syntax. (line 8) +* M68HC11 addressing modes: M68HC11-Syntax. (line 17) +* M68HC11 and M68HC12 support: M68HC11-Dependent. (line 6) +* M68HC11 assembler directive .far: M68HC11-Directives. (line 20) +* M68HC11 assembler directive .interrupt: M68HC11-Directives. (line 26) +* M68HC11 assembler directive .mode: M68HC11-Directives. (line 16) +* M68HC11 assembler directive .relax: M68HC11-Directives. (line 10) +* M68HC11 assembler directive .xrefb: M68HC11-Directives. (line 31) +* M68HC11 assembler directives: M68HC11-Directives. (line 6) +* M68HC11 branch improvement: M68HC11-Branch. (line 6) +* M68HC11 floating point: M68HC11-Float. (line 6) +* M68HC11 modifiers: M68HC11-Modifiers. (line 6) +* M68HC11 opcodes: M68HC11-opcodes. (line 6) +* M68HC11 options: M68HC11-Opts. (line 6) +* M68HC11 pseudo-opcodes: M68HC11-Branch. (line 6) +* M68HC11 syntax: M68HC11-Syntax. (line 6) +* M68HC12 assembler directives: M68HC11-Directives. (line 6) +* machine dependencies: Machine Dependencies. + (line 6) +* machine directives, ARC: ARC Directives. (line 6) +* machine directives, ARM: ARM Directives. (line 6) +* machine directives, H8/300 (none): H8/300 Directives. (line 6) +* machine directives, i860: Directives-i860. (line 6) +* machine directives, i960: Directives-i960. (line 6) +* machine directives, MSP 430: MSP430 Directives. (line 6) +* machine directives, SH: SH Directives. (line 6) +* machine directives, SH64: SH64 Directives. (line 9) +* machine directives, SPARC: Sparc-Directives. (line 6) +* machine directives, TIC54X: TIC54X-Directives. (line 6) +* machine directives, V850: V850 Directives. (line 6) +* machine directives, VAX: VAX-directives. (line 6) +* machine directives, x86: i386-Directives. (line 6) +* machine independent directives: Pseudo Ops. (line 6) +* machine instructions (not covered): Manual. (line 14) +* machine-independent syntax: Syntax. (line 6) +* macro directive: Macro. (line 28) +* macro directive, TIC54X: TIC54X-Directives. (line 153) +* macros: Macro. (line 6) +* macros, count executed: Macro. (line 143) +* Macros, MSP 430: MSP430-Macros. (line 6) +* macros, TIC54X: TIC54X-Macros. (line 6) +* make rules: MD. (line 6) +* manual, structure and purpose: Manual. (line 6) +* math builtins, TIC54X: TIC54X-Builtins. (line 6) +* Maximum number of continuation lines: listing. (line 34) +* memory references, i386: i386-Memory. (line 6) +* memory references, x86-64: i386-Memory. (line 6) +* memory-mapped registers, TIC54X: TIC54X-MMRegs. (line 6) +* merging text and data sections: R. (line 6) +* messages from assembler: Errors. (line 6) +* MicroBlaze architectures: MicroBlaze-Dependent. + (line 6) +* MicroBlaze directives: MicroBlaze Directives. + (line 6) +* MicroBlaze support: MicroBlaze-Dependent. + (line 13) +* minus, permitted arguments: Infix Ops. (line 49) +* MIPS architecture options: MIPS Opts. (line 29) +* MIPS big-endian output: MIPS Opts. (line 13) +* MIPS CPU override: MIPS ISA. (line 18) +* MIPS debugging directives: MIPS Stabs. (line 6) +* MIPS DSP Release 1 instruction generation override: MIPS ASE instruction generation overrides. + (line 21) +* MIPS DSP Release 2 instruction generation override: MIPS ASE instruction generation overrides. + (line 26) +* MIPS ECOFF sections: MIPS Object. (line 6) +* MIPS endianness: Overview. (line 641) +* MIPS ISA: Overview. (line 647) +* MIPS ISA override: MIPS ISA. (line 6) +* MIPS little-endian output: MIPS Opts. (line 13) +* MIPS MDMX instruction generation override: MIPS ASE instruction generation overrides. + (line 16) +* MIPS MIPS-3D instruction generation override: MIPS ASE instruction generation overrides. + (line 6) +* MIPS MT instruction generation override: MIPS ASE instruction generation overrides. + (line 32) +* MIPS option stack: MIPS option stack. (line 6) +* MIPS processor: MIPS-Dependent. (line 6) +* MIT: M68K-Syntax. (line 6) +* mlib directive, TIC54X: TIC54X-Directives. (line 159) +* mlist directive, TIC54X: TIC54X-Directives. (line 164) +* MMIX assembler directive BSPEC: MMIX-Pseudos. (line 131) +* MMIX assembler directive BYTE: MMIX-Pseudos. (line 97) +* MMIX assembler directive ESPEC: MMIX-Pseudos. (line 131) +* MMIX assembler directive GREG: MMIX-Pseudos. (line 50) +* MMIX assembler directive IS: MMIX-Pseudos. (line 42) +* MMIX assembler directive LOC: MMIX-Pseudos. (line 7) +* MMIX assembler directive LOCAL: MMIX-Pseudos. (line 28) +* MMIX assembler directive OCTA: MMIX-Pseudos. (line 108) +* MMIX assembler directive PREFIX: MMIX-Pseudos. (line 120) +* MMIX assembler directive TETRA: MMIX-Pseudos. (line 108) +* MMIX assembler directive WYDE: MMIX-Pseudos. (line 108) +* MMIX assembler directives: MMIX-Pseudos. (line 6) +* MMIX line comment characters: MMIX-Chars. (line 6) +* MMIX options: MMIX-Opts. (line 6) +* MMIX pseudo-op BSPEC: MMIX-Pseudos. (line 131) +* MMIX pseudo-op BYTE: MMIX-Pseudos. (line 97) +* MMIX pseudo-op ESPEC: MMIX-Pseudos. (line 131) +* MMIX pseudo-op GREG: MMIX-Pseudos. (line 50) +* MMIX pseudo-op IS: MMIX-Pseudos. (line 42) +* MMIX pseudo-op LOC: MMIX-Pseudos. (line 7) +* MMIX pseudo-op LOCAL: MMIX-Pseudos. (line 28) +* MMIX pseudo-op OCTA: MMIX-Pseudos. (line 108) +* MMIX pseudo-op PREFIX: MMIX-Pseudos. (line 120) +* MMIX pseudo-op TETRA: MMIX-Pseudos. (line 108) +* MMIX pseudo-op WYDE: MMIX-Pseudos. (line 108) +* MMIX pseudo-ops: MMIX-Pseudos. (line 6) +* MMIX register names: MMIX-Regs. (line 6) +* MMIX support: MMIX-Dependent. (line 6) +* mmixal differences: MMIX-mmixal. (line 6) +* mmregs directive, TIC54X: TIC54X-Directives. (line 170) +* mmsg directive, TIC54X: TIC54X-Directives. (line 77) +* MMX, i386: i386-SIMD. (line 6) +* MMX, x86-64: i386-SIMD. (line 6) +* mnemonic compatibility, i386: i386-Mnemonics. (line 61) +* mnemonic suffixes, i386: i386-Syntax. (line 29) +* mnemonic suffixes, x86-64: i386-Syntax. (line 29) +* mnemonics for opcodes, VAX: VAX-opcodes. (line 6) +* mnemonics, AVR: AVR Opcodes. (line 6) +* mnemonics, D10V: D10V-Opcodes. (line 6) +* mnemonics, D30V: D30V-Opcodes. (line 6) +* mnemonics, H8/300: H8/300 Opcodes. (line 6) +* mnemonics, LM32: LM32 Opcodes. (line 6) +* mnemonics, SH: SH Opcodes. (line 6) +* mnemonics, SH64: SH64 Opcodes. (line 6) +* mnemonics, Z8000: Z8000 Opcodes. (line 6) +* mnolist directive, TIC54X: TIC54X-Directives. (line 164) +* Motorola syntax for the 680x0: M68K-Moto-Syntax. (line 6) +* MOVI instructions, relaxation: Xtensa Immediate Relaxation. + (line 12) +* MOVW and MOVT relocations, ARM: ARM-Relocations. (line 20) +* MRI compatibility mode: M. (line 6) +* mri directive: MRI. (line 6) +* MRI mode, temporarily: MRI. (line 6) +* MSP 430 floating point (IEEE): MSP430 Floating Point. + (line 6) +* MSP 430 identifiers: MSP430-Chars. (line 8) +* MSP 430 line comment character: MSP430-Chars. (line 6) +* MSP 430 machine directives: MSP430 Directives. (line 6) +* MSP 430 macros: MSP430-Macros. (line 6) +* MSP 430 opcodes: MSP430 Opcodes. (line 6) +* MSP 430 options (none): MSP430 Options. (line 6) +* MSP 430 profiling capability: MSP430 Profiling Capability. + (line 6) +* MSP 430 register names: MSP430-Regs. (line 6) +* MSP 430 support: MSP430-Dependent. (line 6) +* MSP430 Assembler Extensions: MSP430-Ext. (line 6) +* mul instruction, i386: i386-Notes. (line 6) +* mul instruction, x86-64: i386-Notes. (line 6) +* name: Z8000 Directives. (line 18) +* named section: Section. (line 6) +* named sections: Ld Sections. (line 8) +* names, symbol: Symbol Names. (line 6) +* naming object file: o. (line 6) +* new page, in listings: Eject. (line 6) +* newblock directive, TIC54X: TIC54X-Directives. (line 176) +* newline (\n): Strings. (line 21) +* newline, required at file end: Statements. (line 13) +* no-absolute-literals directive: Absolute Literals Directive. + (line 6) +* no-longcalls directive: Longcalls Directive. (line 6) +* no-schedule directive: Schedule Directive. (line 6) +* no-transform directive: Transform Directive. (line 6) +* nolist directive: Nolist. (line 6) +* nolist directive, TIC54X: TIC54X-Directives. (line 131) +* NOP pseudo op, ARM: ARM Opcodes. (line 9) +* notes for Alpha: Alpha Notes. (line 6) +* null-terminated strings: Asciz. (line 6) +* number constants: Numbers. (line 6) +* number of macros executed: Macro. (line 143) +* numbered subsections: Sub-Sections. (line 6) +* numbers, 16-bit: hword. (line 6) +* numeric values: Expressions. (line 6) +* nword directive, SPARC: Sparc-Directives. (line 20) +* object attributes: Object Attributes. (line 6) +* object file: Object. (line 6) +* object file format: Object Formats. (line 6) +* object file name: o. (line 6) +* object file, after errors: Z. (line 6) +* obsolescent directives: Deprecated. (line 6) +* octa directive: Octa. (line 6) +* octal character code (\DDD): Strings. (line 30) +* octal integers: Integers. (line 9) +* offset directive, V850: V850 Directives. (line 6) +* opcode mnemonics, VAX: VAX-opcodes. (line 6) +* opcode names, Xtensa: Xtensa Opcodes. (line 6) +* opcode summary, AVR: AVR Opcodes. (line 6) +* opcode summary, D10V: D10V-Opcodes. (line 6) +* opcode summary, D30V: D30V-Opcodes. (line 6) +* opcode summary, H8/300: H8/300 Opcodes. (line 6) +* opcode summary, LM32: LM32 Opcodes. (line 6) +* opcode summary, SH: SH Opcodes. (line 6) +* opcode summary, SH64: SH64 Opcodes. (line 6) +* opcode summary, Z8000: Z8000 Opcodes. (line 6) +* opcodes for ARC: ARC Opcodes. (line 6) +* opcodes for ARM: ARM Opcodes. (line 6) +* opcodes for MSP 430: MSP430 Opcodes. (line 6) +* opcodes for V850: V850 Opcodes. (line 6) +* opcodes, i860: Opcodes for i860. (line 6) +* opcodes, i960: Opcodes for i960. (line 6) +* opcodes, M680x0: M68K-opcodes. (line 6) +* opcodes, M68HC11: M68HC11-opcodes. (line 6) +* operand delimiters, i386: i386-Syntax. (line 15) +* operand delimiters, x86-64: i386-Syntax. (line 15) +* operand notation, VAX: VAX-operands. (line 6) +* operands in expressions: Arguments. (line 6) +* operator precedence: Infix Ops. (line 11) +* operators, in expressions: Operators. (line 6) +* operators, permitted arguments: Infix Ops. (line 6) +* optimization, D10V: Overview. (line 420) +* optimization, D30V: Overview. (line 425) +* optimizations: Xtensa Optimizations. + (line 6) +* option directive, ARC: ARC Directives. (line 162) +* option directive, TIC54X: TIC54X-Directives. (line 180) +* option summary: Overview. (line 6) +* options for Alpha: Alpha Options. (line 6) +* options for ARC (none): ARC Options. (line 6) +* options for ARM (none): ARM Options. (line 6) +* options for AVR (none): AVR Options. (line 6) +* options for Blackfin (none): Blackfin Options. (line 6) +* options for i386: i386-Options. (line 6) +* options for IA-64: IA-64 Options. (line 6) +* options for LM32 (none): LM32 Options. (line 6) +* options for MSP430 (none): MSP430 Options. (line 6) +* options for PDP-11: PDP-11-Options. (line 6) +* options for PowerPC: PowerPC-Opts. (line 6) +* options for s390: s390 Options. (line 6) +* options for SCORE: SCORE-Opts. (line 6) +* options for SPARC: Sparc-Opts. (line 6) +* options for V850 (none): V850 Options. (line 6) +* options for VAX/VMS: VAX-Opts. (line 42) +* options for x86-64: i386-Options. (line 6) +* options for Z80: Z80 Options. (line 6) +* options, all versions of assembler: Invoking. (line 6) +* options, command line: Command Line. (line 13) +* options, CRIS: CRIS-Opts. (line 6) +* options, D10V: D10V-Opts. (line 6) +* options, D30V: D30V-Opts. (line 6) +* options, H8/300: H8/300 Options. (line 6) +* options, i960: Options-i960. (line 6) +* options, IP2K: IP2K-Opts. (line 6) +* options, M32C: M32C-Opts. (line 6) +* options, M32R: M32R-Opts. (line 6) +* options, M680x0: M68K-Opts. (line 6) +* options, M68HC11: M68HC11-Opts. (line 6) +* options, MMIX: MMIX-Opts. (line 6) +* options, PJ: PJ Options. (line 6) +* options, SH: SH Options. (line 6) +* options, SH64: SH64 Options. (line 6) +* options, TIC54X: TIC54X-Opts. (line 6) +* options, Z8000: Z8000 Options. (line 6) +* org directive: Org. (line 6) +* other attribute, of a.out symbol: Symbol Other. (line 6) +* output file: Object. (line 6) +* p2align directive: P2align. (line 6) +* p2alignl directive: P2align. (line 28) +* p2alignw directive: P2align. (line 28) +* padding the location counter: Align. (line 6) +* padding the location counter given a power of two: P2align. (line 6) +* padding the location counter given number of bytes: Balign. (line 6) +* page, in listings: Eject. (line 6) +* paper size, for listings: Psize. (line 6) +* paths for .include: I. (line 6) +* patterns, writing in memory: Fill. (line 6) +* PDP-11 comments: PDP-11-Syntax. (line 16) +* PDP-11 floating-point register syntax: PDP-11-Syntax. (line 13) +* PDP-11 general-purpose register syntax: PDP-11-Syntax. (line 10) +* PDP-11 instruction naming: PDP-11-Mnemonics. (line 6) +* PDP-11 support: PDP-11-Dependent. (line 6) +* PDP-11 syntax: PDP-11-Syntax. (line 6) +* PIC code generation for ARM: ARM Options. (line 139) +* PIC code generation for M32R: M32R-Opts. (line 42) +* PIC selection, MIPS: MIPS Opts. (line 21) +* PJ endianness: Overview. (line 548) +* PJ options: PJ Options. (line 6) +* PJ support: PJ-Dependent. (line 6) +* plus, permitted arguments: Infix Ops. (line 44) +* popsection directive: PopSection. (line 6) +* Position-independent code, CRIS: CRIS-Opts. (line 27) +* Position-independent code, symbols in, CRIS: CRIS-Pic. (line 6) +* PowerPC architectures: PowerPC-Opts. (line 6) +* PowerPC directives: PowerPC-Pseudo. (line 6) +* PowerPC options: PowerPC-Opts. (line 6) +* PowerPC support: PPC-Dependent. (line 6) +* precedence of operators: Infix Ops. (line 11) +* precision, floating point: Flonums. (line 6) +* prefix operators: Prefix Ops. (line 6) +* prefixes, i386: i386-Prefixes. (line 6) +* preprocessing: Preprocessing. (line 6) +* preprocessing, turning on and off: Preprocessing. (line 27) +* previous directive: Previous. (line 6) +* primary attributes, COFF symbols: COFF Symbols. (line 13) +* print directive: Print. (line 6) +* proc directive, SPARC: Sparc-Directives. (line 25) +* profiler directive, MSP 430: MSP430 Directives. (line 22) +* profiling capability for MSP 430: MSP430 Profiling Capability. + (line 6) +* protected directive: Protected. (line 6) +* pseudo-op .arch, CRIS: CRIS-Pseudos. (line 45) +* pseudo-op .dword, CRIS: CRIS-Pseudos. (line 12) +* pseudo-op .syntax, CRIS: CRIS-Pseudos. (line 17) +* pseudo-op BSPEC, MMIX: MMIX-Pseudos. (line 131) +* pseudo-op BYTE, MMIX: MMIX-Pseudos. (line 97) +* pseudo-op ESPEC, MMIX: MMIX-Pseudos. (line 131) +* pseudo-op GREG, MMIX: MMIX-Pseudos. (line 50) +* pseudo-op IS, MMIX: MMIX-Pseudos. (line 42) +* pseudo-op LOC, MMIX: MMIX-Pseudos. (line 7) +* pseudo-op LOCAL, MMIX: MMIX-Pseudos. (line 28) +* pseudo-op OCTA, MMIX: MMIX-Pseudos. (line 108) +* pseudo-op PREFIX, MMIX: MMIX-Pseudos. (line 120) +* pseudo-op TETRA, MMIX: MMIX-Pseudos. (line 108) +* pseudo-op WYDE, MMIX: MMIX-Pseudos. (line 108) +* pseudo-opcodes, M680x0: M68K-Branch. (line 6) +* pseudo-opcodes, M68HC11: M68HC11-Branch. (line 6) +* pseudo-ops for branch, VAX: VAX-branch. (line 6) +* pseudo-ops, CRIS: CRIS-Pseudos. (line 6) +* pseudo-ops, machine independent: Pseudo Ops. (line 6) +* pseudo-ops, MMIX: MMIX-Pseudos. (line 6) +* psize directive: Psize. (line 6) +* PSR bits: IA-64-Bits. (line 6) +* pstring directive, TIC54X: TIC54X-Directives. (line 209) +* psw register, V850: V850-Regs. (line 116) +* purgem directive: Purgem. (line 6) +* purpose of GNU assembler: GNU Assembler. (line 12) +* pushsection directive: PushSection. (line 6) +* quad directive: Quad. (line 6) +* quad directive, i386: i386-Float. (line 21) +* quad directive, x86-64: i386-Float. (line 21) +* real-mode code, i386: i386-16bit. (line 6) +* ref directive, TIC54X: TIC54X-Directives. (line 103) +* register directive, SPARC: Sparc-Directives. (line 29) +* register names, Alpha: Alpha-Regs. (line 6) +* register names, ARC: ARC-Regs. (line 6) +* register names, ARM: ARM-Regs. (line 6) +* register names, AVR: AVR-Regs. (line 6) +* register names, CRIS: CRIS-Regs. (line 6) +* register names, H8/300: H8/300-Regs. (line 6) +* register names, IA-64: IA-64-Regs. (line 6) +* register names, LM32: LM32-Regs. (line 6) +* register names, MMIX: MMIX-Regs. (line 6) +* register names, MSP 430: MSP430-Regs. (line 6) +* register names, Sparc: Sparc-Regs. (line 6) +* register names, V850: V850-Regs. (line 6) +* register names, VAX: VAX-operands. (line 17) +* register names, Xtensa: Xtensa Registers. (line 6) +* register names, Z80: Z80-Regs. (line 6) +* register naming, s390: s390 Register. (line 6) +* register operands, i386: i386-Syntax. (line 15) +* register operands, x86-64: i386-Syntax. (line 15) +* registers, D10V: D10V-Regs. (line 6) +* registers, D30V: D30V-Regs. (line 6) +* registers, i386: i386-Regs. (line 6) +* registers, SH: SH-Regs. (line 6) +* registers, SH64: SH64-Regs. (line 6) +* registers, TIC54X memory-mapped: TIC54X-MMRegs. (line 6) +* registers, x86-64: i386-Regs. (line 6) +* registers, Z8000: Z8000-Regs. (line 6) +* relaxation: Xtensa Relaxation. (line 6) +* relaxation of ADDI instructions: Xtensa Immediate Relaxation. + (line 43) +* relaxation of branch instructions: Xtensa Branch Relaxation. + (line 6) +* relaxation of call instructions: Xtensa Call Relaxation. + (line 6) +* relaxation of immediate fields: Xtensa Immediate Relaxation. + (line 6) +* relaxation of L16SI instructions: Xtensa Immediate Relaxation. + (line 23) +* relaxation of L16UI instructions: Xtensa Immediate Relaxation. + (line 23) +* relaxation of L32I instructions: Xtensa Immediate Relaxation. + (line 23) +* relaxation of L8UI instructions: Xtensa Immediate Relaxation. + (line 23) +* relaxation of MOVI instructions: Xtensa Immediate Relaxation. + (line 12) +* reloc directive: Reloc. (line 6) +* relocation: Sections. (line 6) +* relocation example: Ld Sections. (line 40) +* relocations, Alpha: Alpha-Relocs. (line 6) +* relocations, Sparc: Sparc-Relocs. (line 6) +* repeat prefixes, i386: i386-Prefixes. (line 44) +* reporting bugs in assembler: Reporting Bugs. (line 6) +* rept directive: Rept. (line 6) +* reserve directive, SPARC: Sparc-Directives. (line 39) +* return instructions, i386: i386-Syntax. (line 38) +* return instructions, x86-64: i386-Syntax. (line 38) +* REX prefixes, i386: i386-Prefixes. (line 46) +* rsect: Z8000 Directives. (line 52) +* s390 floating point: s390 Floating Point. (line 6) +* s390 instruction aliases: s390 Aliases. (line 6) +* s390 instruction formats: s390 Formats. (line 6) +* s390 instruction marker: s390 Instruction Marker. + (line 6) +* s390 instruction mnemonics: s390 Mnemonics. (line 6) +* s390 instruction operand modifier: s390 Operand Modifier. + (line 6) +* s390 instruction operands: s390 Operands. (line 6) +* s390 instruction syntax: s390 Syntax. (line 6) +* s390 line comment character: s390 Characters. (line 6) +* s390 literal pool entries: s390 Literal Pool Entries. + (line 6) +* s390 options: s390 Options. (line 6) +* s390 register naming: s390 Register. (line 6) +* s390 support: S/390-Dependent. (line 6) +* sblock directive, TIC54X: TIC54X-Directives. (line 183) +* sbttl directive: Sbttl. (line 6) +* schedule directive: Schedule Directive. (line 6) +* scl directive: Scl. (line 6) +* SCORE architectures: SCORE-Opts. (line 6) +* SCORE directives: SCORE-Pseudo. (line 6) +* SCORE options: SCORE-Opts. (line 6) +* SCORE processor: SCORE-Dependent. (line 6) +* sdaoff pseudo-op, V850: V850 Opcodes. (line 65) +* search path for .include: I. (line 6) +* sect directive, MSP 430: MSP430 Directives. (line 18) +* sect directive, TIC54X: TIC54X-Directives. (line 189) +* section directive (COFF version): Section. (line 16) +* section directive (ELF version): Section. (line 73) +* section directive, V850: V850 Directives. (line 9) +* section override prefixes, i386: i386-Prefixes. (line 23) +* Section Stack <1>: Section. (line 68) +* Section Stack <2>: SubSection. (line 6) +* Section Stack <3>: PopSection. (line 6) +* Section Stack <4>: PushSection. (line 6) +* Section Stack: Previous. (line 6) +* section-relative addressing: Secs Background. (line 68) +* sections: Sections. (line 6) +* sections in messages, internal: As Sections. (line 6) +* sections, i386: i386-Syntax. (line 44) +* sections, named: Ld Sections. (line 8) +* sections, x86-64: i386-Syntax. (line 44) +* seg directive, SPARC: Sparc-Directives. (line 44) +* segm: Z8000 Directives. (line 10) +* set directive: Set. (line 6) +* set directive, TIC54X: TIC54X-Directives. (line 192) +* SH addressing modes: SH-Addressing. (line 6) +* SH floating point (IEEE): SH Floating Point. (line 6) +* SH line comment character: SH-Chars. (line 6) +* SH line separator: SH-Chars. (line 8) +* SH machine directives: SH Directives. (line 6) +* SH opcode summary: SH Opcodes. (line 6) +* SH options: SH Options. (line 6) +* SH registers: SH-Regs. (line 6) +* SH support: SH-Dependent. (line 6) +* SH64 ABI options: SH64 Options. (line 29) +* SH64 addressing modes: SH64-Addressing. (line 6) +* SH64 ISA options: SH64 Options. (line 6) +* SH64 line comment character: SH64-Chars. (line 6) +* SH64 line separator: SH64-Chars. (line 8) +* SH64 machine directives: SH64 Directives. (line 9) +* SH64 opcode summary: SH64 Opcodes. (line 6) +* SH64 options: SH64 Options. (line 6) +* SH64 registers: SH64-Regs. (line 6) +* SH64 support: SH64-Dependent. (line 6) +* shigh directive, M32R: M32R-Directives. (line 26) +* short directive: Short. (line 6) +* short directive, ARC: ARC Directives. (line 171) +* short directive, TIC54X: TIC54X-Directives. (line 111) +* SIMD, i386: i386-SIMD. (line 6) +* SIMD, x86-64: i386-SIMD. (line 6) +* single character constant: Chars. (line 6) +* single directive: Single. (line 6) +* single directive, i386: i386-Float. (line 14) +* single directive, x86-64: i386-Float. (line 14) +* single quote, Z80: Z80-Chars. (line 13) +* sixteen bit integers: hword. (line 6) +* sixteen byte integer: Octa. (line 6) +* size directive (COFF version): Size. (line 11) +* size directive (ELF version): Size. (line 19) +* size modifiers, D10V: D10V-Size. (line 6) +* size modifiers, D30V: D30V-Size. (line 6) +* size modifiers, M680x0: M68K-Syntax. (line 8) +* size prefixes, i386: i386-Prefixes. (line 27) +* size suffixes, H8/300: H8/300 Opcodes. (line 163) +* size, translations, Sparc: Sparc-Size-Translations. + (line 6) +* sizes operands, i386: i386-Syntax. (line 29) +* sizes operands, x86-64: i386-Syntax. (line 29) +* skip directive: Skip. (line 6) +* skip directive, M680x0: M68K-Directives. (line 19) +* skip directive, SPARC: Sparc-Directives. (line 48) +* sleb128 directive: Sleb128. (line 6) +* small objects, MIPS ECOFF: MIPS Object. (line 11) +* SmartMIPS instruction generation override: MIPS ASE instruction generation overrides. + (line 11) +* SOM symbol attributes: SOM Symbols. (line 6) +* source program: Input Files. (line 6) +* source, destination operands; i386: i386-Syntax. (line 22) +* source, destination operands; x86-64: i386-Syntax. (line 22) +* sp register: Xtensa Registers. (line 6) +* sp register, V850: V850-Regs. (line 14) +* space directive: Space. (line 6) +* space directive, TIC54X: TIC54X-Directives. (line 197) +* space used, maximum for assembly: statistics. (line 6) +* SPARC architectures: Sparc-Opts. (line 6) +* Sparc constants: Sparc-Constants. (line 6) +* SPARC data alignment: Sparc-Aligned-Data. (line 6) +* SPARC floating point (IEEE): Sparc-Float. (line 6) +* Sparc line comment character: Sparc-Chars. (line 6) +* Sparc line separator: Sparc-Chars. (line 8) +* SPARC machine directives: Sparc-Directives. (line 6) +* SPARC options: Sparc-Opts. (line 6) +* Sparc registers: Sparc-Regs. (line 6) +* Sparc relocations: Sparc-Relocs. (line 6) +* Sparc size translations: Sparc-Size-Translations. + (line 6) +* SPARC support: Sparc-Dependent. (line 6) +* SPARC syntax: Sparc-Aligned-Data. (line 21) +* special characters, ARC: ARC-Chars. (line 6) +* special characters, M680x0: M68K-Chars. (line 6) +* special purpose registers, MSP 430: MSP430-Regs. (line 11) +* sslist directive, TIC54X: TIC54X-Directives. (line 204) +* ssnolist directive, TIC54X: TIC54X-Directives. (line 204) +* stabd directive: Stab. (line 38) +* stabn directive: Stab. (line 48) +* stabs directive: Stab. (line 51) +* stabX directives: Stab. (line 6) +* standard assembler sections: Secs Background. (line 27) +* standard input, as input file: Command Line. (line 10) +* statement separator character: Statements. (line 6) +* statement separator, Alpha: Alpha-Chars. (line 8) +* statement separator, ARM: ARM-Chars. (line 10) +* statement separator, AVR: AVR-Chars. (line 10) +* statement separator, H8/300: H8/300-Chars. (line 8) +* statement separator, IA-64: IA-64-Chars. (line 8) +* statement separator, SH: SH-Chars. (line 8) +* statement separator, SH64: SH64-Chars. (line 8) +* statement separator, Sparc: Sparc-Chars. (line 8) +* statement separator, Z8000: Z8000-Chars. (line 8) +* statements, structure of: Statements. (line 6) +* statistics, about assembly: statistics. (line 6) +* stopping the assembly: Abort. (line 6) +* string constants: Strings. (line 6) +* string directive: String. (line 8) +* string directive on HPPA: HPPA Directives. (line 137) +* string directive, TIC54X: TIC54X-Directives. (line 209) +* string literals: Ascii. (line 6) +* string, copying to object file: String. (line 8) +* string16 directive: String. (line 8) +* string16, copying to object file: String. (line 8) +* string32 directive: String. (line 8) +* string32, copying to object file: String. (line 8) +* string64 directive: String. (line 8) +* string64, copying to object file: String. (line 8) +* string8 directive: String. (line 8) +* string8, copying to object file: String. (line 8) +* struct directive: Struct. (line 6) +* struct directive, TIC54X: TIC54X-Directives. (line 217) +* structure debugging, COFF: Tag. (line 6) +* sub-instruction ordering, D10V: D10V-Chars. (line 6) +* sub-instruction ordering, D30V: D30V-Chars. (line 6) +* sub-instructions, D10V: D10V-Subs. (line 6) +* sub-instructions, D30V: D30V-Subs. (line 6) +* subexpressions: Arguments. (line 24) +* subsection directive: SubSection. (line 6) +* subsym builtins, TIC54X: TIC54X-Macros. (line 16) +* subtitles for listings: Sbttl. (line 6) +* subtraction, permitted arguments: Infix Ops. (line 49) +* summary of options: Overview. (line 6) +* support: HPPA-Dependent. (line 6) +* supporting files, including: Include. (line 6) +* suppressing warnings: W. (line 11) +* sval: Z8000 Directives. (line 33) +* symbol attributes: Symbol Attributes. (line 6) +* symbol attributes, a.out: a.out Symbols. (line 6) +* symbol attributes, COFF: COFF Symbols. (line 6) +* symbol attributes, SOM: SOM Symbols. (line 6) +* symbol descriptor, COFF: Desc. (line 6) +* symbol modifiers <1>: AVR-Modifiers. (line 12) +* symbol modifiers <2>: LM32-Modifiers. (line 12) +* symbol modifiers <3>: M32C-Modifiers. (line 11) +* symbol modifiers: M68HC11-Modifiers. (line 12) +* symbol names: Symbol Names. (line 6) +* symbol names, $ in <1>: SH-Chars. (line 10) +* symbol names, $ in <2>: SH64-Chars. (line 10) +* symbol names, $ in <3>: D30V-Chars. (line 63) +* symbol names, $ in: D10V-Chars. (line 46) +* symbol names, local: Symbol Names. (line 22) +* symbol names, temporary: Symbol Names. (line 35) +* symbol storage class (COFF): Scl. (line 6) +* symbol type: Symbol Type. (line 6) +* symbol type, COFF: Type. (line 11) +* symbol type, ELF: Type. (line 22) +* symbol value: Symbol Value. (line 6) +* symbol value, setting: Set. (line 6) +* symbol values, assigning: Setting Symbols. (line 6) +* symbol versioning: Symver. (line 6) +* symbol, common: Comm. (line 6) +* symbol, making visible to linker: Global. (line 6) +* symbolic debuggers, information for: Stab. (line 6) +* symbols: Symbols. (line 6) +* Symbols in position-independent code, CRIS: CRIS-Pic. (line 6) +* symbols with uppercase, VAX/VMS: VAX-Opts. (line 42) +* symbols, assigning values to: Equ. (line 6) +* Symbols, built-in, CRIS: CRIS-Symbols. (line 6) +* Symbols, CRIS, built-in: CRIS-Symbols. (line 6) +* symbols, local common: Lcomm. (line 6) +* symver directive: Symver. (line 6) +* syntax compatibility, i386: i386-Syntax. (line 6) +* syntax compatibility, x86-64: i386-Syntax. (line 6) +* syntax, AVR: AVR-Modifiers. (line 6) +* syntax, Blackfin: Blackfin Syntax. (line 6) +* syntax, D10V: D10V-Syntax. (line 6) +* syntax, D30V: D30V-Syntax. (line 6) +* syntax, LM32: LM32-Modifiers. (line 6) +* syntax, M32C: M32C-Modifiers. (line 6) +* syntax, M680x0: M68K-Syntax. (line 8) +* syntax, M68HC11 <1>: M68HC11-Modifiers. (line 6) +* syntax, M68HC11: M68HC11-Syntax. (line 6) +* syntax, machine-independent: Syntax. (line 6) +* syntax, SPARC: Sparc-Aligned-Data. (line 21) +* syntax, Xtensa assembler: Xtensa Syntax. (line 6) +* sysproc directive, i960: Directives-i960. (line 37) +* tab (\t): Strings. (line 27) +* tab directive, TIC54X: TIC54X-Directives. (line 248) +* tag directive: Tag. (line 6) +* tag directive, TIC54X: TIC54X-Directives. (line 251) +* tdaoff pseudo-op, V850: V850 Opcodes. (line 81) +* temporary symbol names: Symbol Names. (line 35) +* text and data sections, joining: R. (line 6) +* text directive: Text. (line 6) +* text section: Ld Sections. (line 9) +* tfloat directive, i386: i386-Float. (line 14) +* tfloat directive, x86-64: i386-Float. (line 14) +* Thumb support: ARM-Dependent. (line 6) +* TIC54X builtin math functions: TIC54X-Builtins. (line 6) +* TIC54X machine directives: TIC54X-Directives. (line 6) +* TIC54X memory-mapped registers: TIC54X-MMRegs. (line 6) +* TIC54X options: TIC54X-Opts. (line 6) +* TIC54X subsym builtins: TIC54X-Macros. (line 16) +* TIC54X support: TIC54X-Dependent. (line 6) +* TIC54X-specific macros: TIC54X-Macros. (line 6) +* time, total for assembly: statistics. (line 6) +* title directive: Title. (line 6) +* tp register, V850: V850-Regs. (line 20) +* transform directive: Transform Directive. (line 6) +* trusted compiler: f. (line 6) +* turning preprocessing on and off: Preprocessing. (line 27) +* type directive (COFF version): Type. (line 11) +* type directive (ELF version): Type. (line 22) +* type of a symbol: Symbol Type. (line 6) +* ualong directive, SH: SH Directives. (line 6) +* uaword directive, SH: SH Directives. (line 6) +* ubyte directive, TIC54X: TIC54X-Directives. (line 36) +* uchar directive, TIC54X: TIC54X-Directives. (line 36) +* uhalf directive, TIC54X: TIC54X-Directives. (line 111) +* uint directive, TIC54X: TIC54X-Directives. (line 111) +* uleb128 directive: Uleb128. (line 6) +* ulong directive, TIC54X: TIC54X-Directives. (line 135) +* undefined section: Ld Sections. (line 36) +* union directive, TIC54X: TIC54X-Directives. (line 251) +* unsegm: Z8000 Directives. (line 14) +* usect directive, TIC54X: TIC54X-Directives. (line 263) +* ushort directive, TIC54X: TIC54X-Directives. (line 111) +* uword directive, TIC54X: TIC54X-Directives. (line 111) +* V850 command line options: V850 Options. (line 9) +* V850 floating point (IEEE): V850 Floating Point. (line 6) +* V850 line comment character: V850-Chars. (line 6) +* V850 machine directives: V850 Directives. (line 6) +* V850 opcodes: V850 Opcodes. (line 6) +* V850 options (none): V850 Options. (line 6) +* V850 register names: V850-Regs. (line 6) +* V850 support: V850-Dependent. (line 6) +* val directive: Val. (line 6) +* value attribute, COFF: Val. (line 6) +* value of a symbol: Symbol Value. (line 6) +* var directive, TIC54X: TIC54X-Directives. (line 273) +* VAX bitfields not supported: VAX-no. (line 6) +* VAX branch improvement: VAX-branch. (line 6) +* VAX command-line options ignored: VAX-Opts. (line 6) +* VAX displacement sizing character: VAX-operands. (line 12) +* VAX floating point: VAX-float. (line 6) +* VAX immediate character: VAX-operands. (line 6) +* VAX indirect character: VAX-operands. (line 9) +* VAX machine directives: VAX-directives. (line 6) +* VAX opcode mnemonics: VAX-opcodes. (line 6) +* VAX operand notation: VAX-operands. (line 6) +* VAX register names: VAX-operands. (line 17) +* VAX support: Vax-Dependent. (line 6) +* Vax-11 C compatibility: VAX-Opts. (line 42) +* VAX/VMS options: VAX-Opts. (line 42) +* version directive: Version. (line 6) +* version directive, TIC54X: TIC54X-Directives. (line 277) +* version of assembler: v. (line 6) +* versions of symbols: Symver. (line 6) +* visibility <1>: Internal. (line 6) +* visibility <2>: Protected. (line 6) +* visibility: Hidden. (line 6) +* VMS (VAX) options: VAX-Opts. (line 42) +* vtable_entry directive: VTableEntry. (line 6) +* vtable_inherit directive: VTableInherit. (line 6) +* warning directive: Warning. (line 6) +* warning for altered difference tables: K. (line 6) +* warning messages: Errors. (line 6) +* warnings, causing error: W. (line 16) +* warnings, M32R: M32R-Warnings. (line 6) +* warnings, suppressing: W. (line 11) +* warnings, switching on: W. (line 19) +* weak directive: Weak. (line 6) +* weakref directive: Weakref. (line 6) +* whitespace: Whitespace. (line 6) +* whitespace, removed by preprocessor: Preprocessing. (line 7) +* wide floating point directives, VAX: VAX-directives. (line 10) +* width directive, TIC54X: TIC54X-Directives. (line 127) +* Width of continuation lines of disassembly output: listing. (line 21) +* Width of first line disassembly output: listing. (line 16) +* Width of source line output: listing. (line 28) +* wmsg directive, TIC54X: TIC54X-Directives. (line 77) +* word directive: Word. (line 6) +* word directive, ARC: ARC Directives. (line 174) +* word directive, H8/300: H8/300 Directives. (line 6) +* word directive, i386: i386-Float. (line 21) +* word directive, SPARC: Sparc-Directives. (line 51) +* word directive, TIC54X: TIC54X-Directives. (line 111) +* word directive, x86-64: i386-Float. (line 21) +* writing patterns in memory: Fill. (line 6) +* wval: Z8000 Directives. (line 24) +* x86 machine directives: i386-Directives. (line 6) +* x86-64 arch directive: i386-Arch. (line 6) +* x86-64 att_syntax pseudo op: i386-Syntax. (line 6) +* x86-64 conversion instructions: i386-Mnemonics. (line 36) +* x86-64 floating point: i386-Float. (line 6) +* x86-64 immediate operands: i386-Syntax. (line 15) +* x86-64 instruction naming: i386-Mnemonics. (line 6) +* x86-64 intel_syntax pseudo op: i386-Syntax. (line 6) +* x86-64 jump optimization: i386-Jumps. (line 6) +* x86-64 jump, call, return: i386-Syntax. (line 38) +* x86-64 jump/call operands: i386-Syntax. (line 15) +* x86-64 memory references: i386-Memory. (line 6) +* x86-64 options: i386-Options. (line 6) +* x86-64 register operands: i386-Syntax. (line 15) +* x86-64 registers: i386-Regs. (line 6) +* x86-64 sections: i386-Syntax. (line 44) +* x86-64 size suffixes: i386-Syntax. (line 29) +* x86-64 source, destination operands: i386-Syntax. (line 22) +* x86-64 support: i386-Dependent. (line 6) +* x86-64 syntax compatibility: i386-Syntax. (line 6) +* xfloat directive, TIC54X: TIC54X-Directives. (line 64) +* xlong directive, TIC54X: TIC54X-Directives. (line 135) +* Xtensa architecture: Xtensa-Dependent. (line 6) +* Xtensa assembler syntax: Xtensa Syntax. (line 6) +* Xtensa directives: Xtensa Directives. (line 6) +* Xtensa opcode names: Xtensa Opcodes. (line 6) +* Xtensa register names: Xtensa Registers. (line 6) +* xword directive, SPARC: Sparc-Directives. (line 55) +* Z80 $: Z80-Chars. (line 8) +* Z80 ': Z80-Chars. (line 13) +* Z80 floating point: Z80 Floating Point. (line 6) +* Z80 line comment character: Z80-Chars. (line 6) +* Z80 options: Z80 Options. (line 6) +* Z80 registers: Z80-Regs. (line 6) +* Z80 support: Z80-Dependent. (line 6) +* Z80 Syntax: Z80 Options. (line 47) +* Z80, \: Z80-Chars. (line 11) +* Z80, case sensitivity: Z80-Case. (line 6) +* Z80-only directives: Z80 Directives. (line 9) +* Z800 addressing modes: Z8000-Addressing. (line 6) +* Z8000 directives: Z8000 Directives. (line 6) +* Z8000 line comment character: Z8000-Chars. (line 6) +* Z8000 line separator: Z8000-Chars. (line 8) +* Z8000 opcode summary: Z8000 Opcodes. (line 6) +* Z8000 options: Z8000 Options. (line 6) +* Z8000 registers: Z8000-Regs. (line 6) +* Z8000 support: Z8000-Dependent. (line 6) +* zdaoff pseudo-op, V850: V850 Opcodes. (line 99) +* zero register, V850: V850-Regs. (line 7) +* zero-terminated strings: Asciz. (line 6) + + + +Tag Table: +Node: Top770 +Node: Overview1758 +Node: Manual30675 +Node: GNU Assembler31619 +Node: Object Formats32790 +Node: Command Line33242 +Node: Input Files34329 +Node: Object36310 +Node: Errors37206 +Node: Invoking38401 +Node: a40356 +Node: alternate42267 +Node: D42439 +Node: f42672 +Node: I43180 +Node: K43724 +Node: L44028 +Node: listing44767 +Node: M46426 +Node: MD50827 +Node: o51253 +Node: R51708 +Node: statistics52738 +Node: traditional-format53145 +Node: v53618 +Node: W53893 +Node: Z54800 +Node: Syntax55322 +Node: Preprocessing55913 +Node: Whitespace57476 +Node: Comments57872 +Node: Symbol Intro60071 +Node: Statements60761 +Node: Constants62682 +Node: Characters63313 +Node: Strings63815 +Node: Chars65981 +Node: Numbers66735 +Node: Integers67275 +Node: Bignums67931 +Node: Flonums68287 +Node: Sections70034 +Node: Secs Background70412 +Node: Ld Sections75451 +Node: As Sections77835 +Node: Sub-Sections78745 +Node: bss81890 +Node: Symbols82840 +Node: Labels83488 +Node: Setting Symbols84219 +Node: Symbol Names84773 +Node: Dot89814 +Node: Symbol Attributes90261 +Node: Symbol Value90998 +Node: Symbol Type92043 +Node: a.out Symbols92431 +Node: Symbol Desc92693 +Node: Symbol Other92988 +Node: COFF Symbols93157 +Node: SOM Symbols93830 +Node: Expressions94272 +Node: Empty Exprs95021 +Node: Integer Exprs95368 +Node: Arguments95763 +Node: Operators96869 +Node: Prefix Ops97204 +Node: Infix Ops97532 +Node: Pseudo Ops99922 +Node: Abort105423 +Node: ABORT (COFF)105835 +Node: Align106043 +Node: Altmacro108325 +Node: Ascii109654 +Node: Asciz109963 +Node: Balign110208 +Node: Byte112071 +Node: CFI directives112319 +Node: Comm117946 +Ref: Comm-Footnote-1119547 +Node: Data119909 +Node: Def120226 +Node: Desc120458 +Node: Dim120958 +Node: Double121215 +Node: Eject121553 +Node: Else121728 +Node: Elseif122028 +Node: End122322 +Node: Endef122537 +Node: Endfunc122714 +Node: Endif122889 +Node: Equ123150 +Node: Equiv123664 +Node: Eqv124220 +Node: Err124584 +Node: Error124895 +Node: Exitm125340 +Node: Extern125509 +Node: Fail125770 +Node: File126215 +Node: Fill127544 +Node: Float128508 +Node: Func128850 +Node: Global129440 +Node: Gnu_attribute130197 +Node: Hidden130422 +Node: hword131008 +Node: Ident131336 +Node: If131910 +Node: Incbin134969 +Node: Include135664 +Node: Int136215 +Node: Internal136596 +Node: Irp137244 +Node: Irpc138123 +Node: Lcomm139040 +Node: Lflags139788 +Node: Line139982 +Node: Linkonce140895 +Node: List142124 +Node: Ln142732 +Node: Loc142882 +Node: Loc_mark_labels144268 +Node: Local144752 +Node: Long145364 +Node: Macro145542 +Node: MRI151464 +Node: Noaltmacro151802 +Node: Nolist151971 +Node: Octa152401 +Node: Org152735 +Node: P2align154018 +Node: PopSection155946 +Node: Previous156454 +Node: Print157867 +Node: Protected158096 +Node: Psize158743 +Node: Purgem159427 +Node: PushSection159648 +Node: Quad160391 +Node: Reloc160847 +Node: Rept161608 +Node: Sbttl162022 +Node: Scl162387 +Node: Section162728 +Node: Set168237 +Node: Short168874 +Node: Single169195 +Node: Size169540 +Node: Skip170214 +Node: Sleb128170538 +Node: Space170862 +Node: Stab171503 +Node: String173507 +Node: Struct174501 +Node: SubSection175226 +Node: Symver175789 +Node: Tag178182 +Node: Text178564 +Node: Title178885 +Node: Type179266 +Node: Uleb128181560 +Node: Val181884 +Node: Version182134 +Node: VTableEntry182409 +Node: VTableInherit182699 +Node: Warning183149 +Node: Weak183383 +Node: Weakref184052 +Node: Word185017 +Node: Deprecated186863 +Node: Object Attributes187098 +Node: GNU Object Attributes188818 +Node: Defining New Object Attributes191371 +Node: Machine Dependencies192168 +Node: Alpha-Dependent195293 +Node: Alpha Notes195707 +Node: Alpha Options195988 +Node: Alpha Syntax198464 +Node: Alpha-Chars198933 +Node: Alpha-Regs199164 +Node: Alpha-Relocs199551 +Node: Alpha Floating Point205809 +Node: Alpha Directives206031 +Node: Alpha Opcodes211554 +Node: ARC-Dependent211849 +Node: ARC Options212232 +Node: ARC Syntax213301 +Node: ARC-Chars213533 +Node: ARC-Regs213665 +Node: ARC Floating Point213789 +Node: ARC Directives214100 +Node: ARC Opcodes220072 +Node: ARM-Dependent220298 +Node: ARM Options220763 +Node: ARM Syntax227896 +Node: ARM-Instruction-Set228210 +Node: ARM-Chars229442 +Node: ARM-Regs229994 +Node: ARM Floating Point230203 +Node: ARM-Relocations230402 +Node: ARM Directives231355 +Ref: arm_pad232219 +Ref: arm_fnend235291 +Ref: arm_fnstart235615 +Ref: arm_save238627 +Ref: arm_setfp239328 +Node: ARM Opcodes242409 +Node: ARM Mapping Symbols244497 +Node: ARM Unwinding Tutorial245307 +Node: AVR-Dependent251509 +Node: AVR Options251799 +Node: AVR Syntax255003 +Node: AVR-Chars255290 +Node: AVR-Regs255696 +Node: AVR-Modifiers256275 +Node: AVR Opcodes258335 +Node: Blackfin-Dependent263581 +Node: Blackfin Options263893 +Node: Blackfin Syntax264751 +Node: Blackfin Directives270484 +Node: CR16-Dependent270903 +Node: CR16 Operand Qualifiers271151 +Node: CRIS-Dependent273792 +Node: CRIS-Opts274138 +Ref: march-option275756 +Node: CRIS-Expand277573 +Node: CRIS-Symbols278756 +Node: CRIS-Syntax279925 +Node: CRIS-Chars280261 +Node: CRIS-Pic280812 +Ref: crispic281008 +Node: CRIS-Regs284548 +Node: CRIS-Pseudos284965 +Ref: crisnous285741 +Node: D10V-Dependent287023 +Node: D10V-Opts287374 +Node: D10V-Syntax288337 +Node: D10V-Size288866 +Node: D10V-Subs289839 +Node: D10V-Chars290874 +Node: D10V-Regs292478 +Node: D10V-Addressing293523 +Node: D10V-Word294209 +Node: D10V-Float294724 +Node: D10V-Opcodes295035 +Node: D30V-Dependent295428 +Node: D30V-Opts295781 +Node: D30V-Syntax296456 +Node: D30V-Size296988 +Node: D30V-Subs297959 +Node: D30V-Chars298994 +Node: D30V-Guarded301292 +Node: D30V-Regs301972 +Node: D30V-Addressing303111 +Node: D30V-Float303779 +Node: D30V-Opcodes304090 +Node: H8/300-Dependent304483 +Node: H8/300 Options304895 +Node: H8/300 Syntax305162 +Node: H8/300-Chars305463 +Node: H8/300-Regs305762 +Node: H8/300-Addressing306681 +Node: H8/300 Floating Point307722 +Node: H8/300 Directives308049 +Node: H8/300 Opcodes309177 +Node: HPPA-Dependent317499 +Node: HPPA Notes317934 +Node: HPPA Options318692 +Node: HPPA Syntax318887 +Node: HPPA Floating Point320157 +Node: HPPA Directives320363 +Node: HPPA Opcodes329049 +Node: ESA/390-Dependent329308 +Node: ESA/390 Notes329768 +Node: ESA/390 Options330559 +Node: ESA/390 Syntax330769 +Node: ESA/390 Floating Point332942 +Node: ESA/390 Directives333221 +Node: ESA/390 Opcodes336510 +Node: i386-Dependent336772 +Node: i386-Options337896 +Node: i386-Directives341863 +Node: i386-Syntax342601 +Node: i386-Mnemonics345034 +Node: i386-Regs348273 +Node: i386-Prefixes350318 +Node: i386-Memory353078 +Node: i386-Jumps356015 +Node: i386-Float357136 +Node: i386-SIMD358967 +Node: i386-16bit360078 +Node: i386-Bugs362118 +Node: i386-Arch362872 +Node: i386-Notes365429 +Node: i860-Dependent366287 +Node: Notes-i860366683 +Node: Options-i860367588 +Node: Directives-i860368951 +Node: Opcodes for i860370020 +Node: i960-Dependent372187 +Node: Options-i960372590 +Node: Floating Point-i960376475 +Node: Directives-i960376743 +Node: Opcodes for i960378777 +Node: callj-i960379394 +Node: Compare-and-branch-i960379883 +Node: IA-64-Dependent381787 +Node: IA-64 Options382088 +Node: IA-64 Syntax385248 +Node: IA-64-Chars385611 +Node: IA-64-Regs385841 +Node: IA-64-Bits386767 +Node: IA-64 Opcodes387276 +Node: IP2K-Dependent387548 +Node: IP2K-Opts387776 +Node: LM32-Dependent388256 +Node: LM32 Options388551 +Node: LM32 Syntax389185 +Node: LM32-Regs389432 +Node: LM32-Modifiers390391 +Node: LM32 Opcodes391747 +Node: M32C-Dependent392051 +Node: M32C-Opts392575 +Node: M32C-Modifiers392998 +Node: M32R-Dependent394785 +Node: M32R-Opts395106 +Node: M32R-Directives399273 +Node: M32R-Warnings403248 +Node: M68K-Dependent406254 +Node: M68K-Opts406721 +Node: M68K-Syntax414113 +Node: M68K-Moto-Syntax415953 +Node: M68K-Float418543 +Node: M68K-Directives419063 +Node: M68K-opcodes420391 +Node: M68K-Branch420617 +Node: M68K-Chars424815 +Node: M68HC11-Dependent425228 +Node: M68HC11-Opts425765 +Node: M68HC11-Syntax429586 +Node: M68HC11-Modifiers431800 +Node: M68HC11-Directives433628 +Node: M68HC11-Float435004 +Node: M68HC11-opcodes435532 +Node: M68HC11-Branch435714 +Node: MicroBlaze-Dependent438163 +Node: MicroBlaze Directives438793 +Node: MIPS-Dependent440150 +Node: MIPS Opts441313 +Node: MIPS Object451057 +Node: MIPS Stabs452623 +Node: MIPS symbol sizes453345 +Node: MIPS ISA455014 +Node: MIPS autoextend456488 +Node: MIPS insn457218 +Node: MIPS option stack458488 +Node: MIPS ASE instruction generation overrides459262 +Node: MIPS floating-point461076 +Node: MMIX-Dependent461962 +Node: MMIX-Opts462342 +Node: MMIX-Expand465946 +Node: MMIX-Syntax467261 +Ref: mmixsite467618 +Node: MMIX-Chars468459 +Node: MMIX-Symbols469113 +Node: MMIX-Regs471181 +Node: MMIX-Pseudos472206 +Ref: MMIX-loc472347 +Ref: MMIX-local473427 +Ref: MMIX-is473959 +Ref: MMIX-greg474230 +Ref: GREG-base475149 +Ref: MMIX-byte476466 +Ref: MMIX-constants476937 +Ref: MMIX-prefix477583 +Ref: MMIX-spec477957 +Node: MMIX-mmixal478291 +Node: MSP430-Dependent481789 +Node: MSP430 Options482255 +Node: MSP430 Syntax482541 +Node: MSP430-Macros482857 +Node: MSP430-Chars483588 +Node: MSP430-Regs483901 +Node: MSP430-Ext484461 +Node: MSP430 Floating Point486282 +Node: MSP430 Directives486506 +Node: MSP430 Opcodes487297 +Node: MSP430 Profiling Capability487692 +Node: PDP-11-Dependent490021 +Node: PDP-11-Options490410 +Node: PDP-11-Pseudos495481 +Node: PDP-11-Syntax495826 +Node: PDP-11-Mnemonics496578 +Node: PDP-11-Synthetic496880 +Node: PJ-Dependent497098 +Node: PJ Options497323 +Node: PPC-Dependent497600 +Node: PowerPC-Opts497887 +Node: PowerPC-Pseudo500439 +Node: S/390-Dependent501038 +Node: s390 Options501741 +Node: s390 Characters503279 +Node: s390 Syntax503472 +Node: s390 Register504373 +Node: s390 Mnemonics505186 +Node: s390 Operands508206 +Node: s390 Formats510825 +Node: s390 Aliases518696 +Node: s390 Operand Modifier522593 +Node: s390 Instruction Marker526394 +Node: s390 Literal Pool Entries527410 +Node: s390 Directives529333 +Node: s390 Floating Point533248 +Node: SCORE-Dependent533694 +Node: SCORE-Opts533968 +Node: SCORE-Pseudo535256 +Node: SH-Dependent537312 +Node: SH Options537724 +Node: SH Syntax538732 +Node: SH-Chars539005 +Node: SH-Regs539299 +Node: SH-Addressing539913 +Node: SH Floating Point540822 +Node: SH Directives541916 +Node: SH Opcodes542286 +Node: SH64-Dependent546608 +Node: SH64 Options546971 +Node: SH64 Syntax548768 +Node: SH64-Chars549051 +Node: SH64-Regs549351 +Node: SH64-Addressing550447 +Node: SH64 Directives551630 +Node: SH64 Opcodes552740 +Node: Sparc-Dependent553456 +Node: Sparc-Opts553868 +Node: Sparc-Aligned-Data556125 +Node: Sparc-Syntax556957 +Node: Sparc-Chars557531 +Node: Sparc-Regs557764 +Node: Sparc-Constants562875 +Node: Sparc-Relocs567635 +Node: Sparc-Size-Translations572315 +Node: Sparc-Float573964 +Node: Sparc-Directives574159 +Node: TIC54X-Dependent576119 +Node: TIC54X-Opts576845 +Node: TIC54X-Block577888 +Node: TIC54X-Env578248 +Node: TIC54X-Constants578596 +Node: TIC54X-Subsyms578998 +Node: TIC54X-Locals580907 +Node: TIC54X-Builtins581651 +Node: TIC54X-Ext584122 +Node: TIC54X-Directives584693 +Node: TIC54X-Macros595595 +Node: TIC54X-MMRegs597706 +Node: Z80-Dependent597922 +Node: Z80 Options598310 +Node: Z80 Syntax599733 +Node: Z80-Chars600405 +Node: Z80-Regs600939 +Node: Z80-Case601291 +Node: Z80 Floating Point601736 +Node: Z80 Directives601930 +Node: Z80 Opcodes603555 +Node: Z8000-Dependent604899 +Node: Z8000 Options605860 +Node: Z8000 Syntax606077 +Node: Z8000-Chars606367 +Node: Z8000-Regs606600 +Node: Z8000-Addressing607390 +Node: Z8000 Directives608507 +Node: Z8000 Opcodes610116 +Node: Vax-Dependent620058 +Node: VAX-Opts620575 +Node: VAX-float624310 +Node: VAX-directives624942 +Node: VAX-opcodes625803 +Node: VAX-branch626192 +Node: VAX-operands628699 +Node: VAX-no629462 +Node: V850-Dependent629699 +Node: V850 Options630097 +Node: V850 Syntax632486 +Node: V850-Chars632726 +Node: V850-Regs632891 +Node: V850 Floating Point634459 +Node: V850 Directives634665 +Node: V850 Opcodes635808 +Node: Xtensa-Dependent641700 +Node: Xtensa Options642429 +Node: Xtensa Syntax645239 +Node: Xtensa Opcodes647128 +Node: Xtensa Registers648922 +Node: Xtensa Optimizations649555 +Node: Density Instructions650007 +Node: Xtensa Automatic Alignment651109 +Node: Xtensa Relaxation653556 +Node: Xtensa Branch Relaxation654464 +Node: Xtensa Call Relaxation655836 +Node: Xtensa Immediate Relaxation657622 +Node: Xtensa Directives660196 +Node: Schedule Directive661905 +Node: Longcalls Directive662245 +Node: Transform Directive662789 +Node: Literal Directive663531 +Ref: Literal Directive-Footnote-1667070 +Node: Literal Position Directive667212 +Node: Literal Prefix Directive668911 +Node: Absolute Literals Directive669809 +Node: Reporting Bugs671116 +Node: Bug Criteria671842 +Node: Bug Reporting672609 +Node: Acknowledgements679258 +Ref: Acknowledgements-Footnote-1684224 +Node: GNU Free Documentation License684250 +Node: AS Index709419 + +End Tag Table |