diff options
Diffstat (limited to 'binutils-2.20.1/gas/doc/c-d10v.texi')
-rw-r--r-- | binutils-2.20.1/gas/doc/c-d10v.texi | 257 |
1 files changed, 257 insertions, 0 deletions
diff --git a/binutils-2.20.1/gas/doc/c-d10v.texi b/binutils-2.20.1/gas/doc/c-d10v.texi new file mode 100644 index 0000000..0def48c --- /dev/null +++ b/binutils-2.20.1/gas/doc/c-d10v.texi @@ -0,0 +1,257 @@ +@c Copyright 1996, 2000, 2002 Free Software Foundation, Inc. +@c This is part of the GAS manual. +@c For copying conditions, see the file as.texinfo. +@ifset GENERIC +@page +@node D10V-Dependent +@chapter D10V Dependent Features +@end ifset +@ifclear GENERIC +@node Machine Dependencies +@chapter D10V Dependent Features +@end ifclear + +@cindex D10V support +@menu +* D10V-Opts:: D10V Options +* D10V-Syntax:: Syntax +* D10V-Float:: Floating Point +* D10V-Opcodes:: Opcodes +@end menu + +@node D10V-Opts +@section D10V Options +@cindex options, D10V +@cindex D10V options +The Mitsubishi D10V version of @code{@value{AS}} has a few machine +dependent options. + +@table @samp +@item -O +The D10V can often execute two sub-instructions in parallel. When this option +is used, @code{@value{AS}} will attempt to optimize its output by detecting when +instructions can be executed in parallel. +@item --nowarnswap +To optimize execution performance, @code{@value{AS}} will sometimes swap the +order of instructions. Normally this generates a warning. When this option +is used, no warning will be generated when instructions are swapped. +@item --gstabs-packing +@item --no-gstabs-packing +@code{@value{AS}} packs adjacent short instructions into a single packed +instruction. @samp{--no-gstabs-packing} turns instruction packing off if +@samp{--gstabs} is specified as well; @samp{--gstabs-packing} (the +default) turns instruction packing on even when @samp{--gstabs} is +specified. +@end table + +@node D10V-Syntax +@section Syntax +@cindex D10V syntax +@cindex syntax, D10V + +The D10V syntax is based on the syntax in Mitsubishi's D10V architecture manual. +The differences are detailed below. + +@menu +* D10V-Size:: Size Modifiers +* D10V-Subs:: Sub-Instructions +* D10V-Chars:: Special Characters +* D10V-Regs:: Register Names +* D10V-Addressing:: Addressing Modes +* D10V-Word:: @@WORD Modifier +@end menu + + +@node D10V-Size +@subsection Size Modifiers +@cindex D10V size modifiers +@cindex size modifiers, D10V +The D10V version of @code{@value{AS}} uses the instruction names in the D10V +Architecture Manual. However, the names in the manual are sometimes ambiguous. +There are instruction names that can assemble to a short or long form opcode. +How does the assembler pick the correct form? @code{@value{AS}} will always pick the +smallest form if it can. When dealing with a symbol that is not defined yet when a +line is being assembled, it will always use the long form. If you need to force the +assembler to use either the short or long form of the instruction, you can append +either @samp{.s} (short) or @samp{.l} (long) to it. For example, if you are writing +an assembly program and you want to do a branch to a symbol that is defined later +in your program, you can write @samp{bra.s foo}. +Objdump and GDB will always append @samp{.s} or @samp{.l} to instructions which +have both short and long forms. + +@node D10V-Subs +@subsection Sub-Instructions +@cindex D10V sub-instructions +@cindex sub-instructions, D10V +The D10V assembler takes as input a series of instructions, either one-per-line, +or in the special two-per-line format described in the next section. Some of these +instructions will be short-form or sub-instructions. These sub-instructions can be packed +into a single instruction. The assembler will do this automatically. It will also detect +when it should not pack instructions. For example, when a label is defined, the next +instruction will never be packaged with the previous one. Whenever a branch and link +instruction is called, it will not be packaged with the next instruction so the return +address will be valid. Nops are automatically inserted when necessary. + +If you do not want the assembler automatically making these decisions, you can control +the packaging and execution type (parallel or sequential) with the special execution +symbols described in the next section. + +@node D10V-Chars +@subsection Special Characters +@cindex line comment character, D10V +@cindex D10V line comment character +@samp{;} and @samp{#} are the line comment characters. +@cindex sub-instruction ordering, D10V +@cindex D10V sub-instruction ordering +Sub-instructions may be executed in order, in reverse-order, or in parallel. +Instructions listed in the standard one-per-line format will be executed sequentially. +To specify the executing order, use the following symbols: +@table @samp +@item -> +Sequential with instruction on the left first. +@item <- +Sequential with instruction on the right first. +@item || +Parallel +@end table +The D10V syntax allows either one instruction per line, one instruction per line with +the execution symbol, or two instructions per line. For example +@table @code +@item abs a1 -> abs r0 +Execute these sequentially. The instruction on the right is in the right +container and is executed second. +@item abs r0 <- abs a1 +Execute these reverse-sequentially. The instruction on the right is in the right +container, and is executed first. +@item ld2w r2,@@r8+ || mac a0,r0,r7 +Execute these in parallel. +@item ld2w r2,@@r8+ || +@itemx mac a0,r0,r7 +Two-line format. Execute these in parallel. +@item ld2w r2,@@r8+ +@itemx mac a0,r0,r7 +Two-line format. Execute these sequentially. Assembler will +put them in the proper containers. +@item ld2w r2,@@r8+ -> +@itemx mac a0,r0,r7 +Two-line format. Execute these sequentially. Same as above but +second instruction will always go into right container. +@end table +@cindex symbol names, @samp{$} in +@cindex @code{$} in symbol names +Since @samp{$} has no special meaning, you may use it in symbol names. + +@node D10V-Regs +@subsection Register Names +@cindex D10V registers +@cindex registers, D10V +You can use the predefined symbols @samp{r0} through @samp{r15} to refer to the D10V +registers. You can also use @samp{sp} as an alias for @samp{r15}. The accumulators +are @samp{a0} and @samp{a1}. There are special register-pair names that may +optionally be used in opcodes that require even-numbered registers. Register names are +not case sensitive. + +Register Pairs +@table @code +@item r0-r1 +@item r2-r3 +@item r4-r5 +@item r6-r7 +@item r8-r9 +@item r10-r11 +@item r12-r13 +@item r14-r15 +@end table + +The D10V also has predefined symbols for these control registers and status bits: +@table @code +@item psw +Processor Status Word +@item bpsw +Backup Processor Status Word +@item pc +Program Counter +@item bpc +Backup Program Counter +@item rpt_c +Repeat Count +@item rpt_s +Repeat Start address +@item rpt_e +Repeat End address +@item mod_s +Modulo Start address +@item mod_e +Modulo End address +@item iba +Instruction Break Address +@item f0 +Flag 0 +@item f1 +Flag 1 +@item c +Carry flag +@end table + +@node D10V-Addressing +@subsection Addressing Modes +@cindex addressing modes, D10V +@cindex D10V addressing modes +@code{@value{AS}} understands the following addressing modes for the D10V. +@code{R@var{n}} in the following refers to any of the numbered +registers, but @emph{not} the control registers. +@table @code +@item R@var{n} +Register direct +@item @@R@var{n} +Register indirect +@item @@R@var{n}+ +Register indirect with post-increment +@item @@R@var{n}- +Register indirect with post-decrement +@item @@-SP +Register indirect with pre-decrement +@item @@(@var{disp}, R@var{n}) +Register indirect with displacement +@item @var{addr} +PC relative address (for branch or rep). +@item #@var{imm} +Immediate data (the @samp{#} is optional and ignored) +@end table + +@node D10V-Word +@subsection @@WORD Modifier +@cindex D10V @@word modifier +@cindex @@word modifier, D10V +Any symbol followed by @code{@@word} will be replaced by the symbol's value +shifted right by 2. This is used in situations such as loading a register +with the address of a function (or any other code fragment). For example, if +you want to load a register with the location of the function @code{main} then +jump to that function, you could do it as follows: +@smallexample +@group +ldi r2, main@@word +jmp r2 +@end group +@end smallexample + +@node D10V-Float +@section Floating Point +@cindex floating point, D10V +@cindex D10V floating point +The D10V has no hardware floating point, but the @code{.float} and @code{.double} +directives generates @sc{ieee} floating-point numbers for compatibility +with other development tools. + +@node D10V-Opcodes +@section Opcodes +@cindex D10V opcode summary +@cindex opcode summary, D10V +@cindex mnemonics, D10V +@cindex instruction summary, D10V +For detailed information on the D10V machine instruction set, see +@cite{D10V Architecture: A VLIW Microprocessor for Multimedia Applications} +(Mitsubishi Electric Corp.). +@code{@value{AS}} implements all the standard D10V opcodes. The only changes are those +described in the section on size modifiers + |