diff options
Diffstat (limited to 'binutils-2.20.1/gas/doc/c-i860.texi')
-rw-r--r-- | binutils-2.20.1/gas/doc/c-i860.texi | 172 |
1 files changed, 172 insertions, 0 deletions
diff --git a/binutils-2.20.1/gas/doc/c-i860.texi b/binutils-2.20.1/gas/doc/c-i860.texi new file mode 100644 index 0000000..22f1377 --- /dev/null +++ b/binutils-2.20.1/gas/doc/c-i860.texi @@ -0,0 +1,172 @@ +@c Copyright 2000, 2003 Free Software Foundation, Inc. +@c This is part of the GAS manual. +@c For copying conditions, see the file as.texinfo. +@ifset GENERIC +@page +@node i860-Dependent +@chapter Intel i860 Dependent Features +@end ifset +@ifclear GENERIC +@node Machine Dependencies +@chapter Intel i860 Dependent Features +@end ifclear + +@ignore +@c FIXME: This is basically a stub for i860. There is tons more information +that I will add later (jle@cygnus.com). +@end ignore + +@cindex i860 support +@menu +* Notes-i860:: i860 Notes +* Options-i860:: i860 Command-line Options +* Directives-i860:: i860 Machine Directives +* Opcodes for i860:: i860 Opcodes +@end menu + +@node Notes-i860 +@section i860 Notes +This is a fairly complete i860 assembler which is compatible with the +UNIX System V/860 Release 4 assembler. However, it does not currently +support SVR4 PIC (i.e., @code{@@GOT, @@GOTOFF, @@PLT}). + +Like the SVR4/860 assembler, the output object format is ELF32. Currently, +this is the only supported object format. If there is sufficient interest, +other formats such as COFF may be implemented. + +Both the Intel and AT&T/SVR4 syntaxes are supported, with the latter +being the default. One difference is that AT&T syntax requires the '%' +prefix on register names while Intel syntax does not. Another difference +is in the specification of relocatable expressions. The Intel syntax +is @code{ha%expression} whereas the SVR4 syntax is @code{[expression]@@ha} +(and similarly for the "l" and "h" selectors). +@node Options-i860 +@section i860 Command-line Options +@subsection SVR4 compatibility options +@table @code +@item -V +Print assembler version. +@item -Qy +Ignored. +@item -Qn +Ignored. +@end table +@subsection Other options +@table @code +@item -EL +Select little endian output (this is the default). +@item -EB +Select big endian output. Note that the i860 always reads instructions +as little endian data, so this option only effects data and not +instructions. +@item -mwarn-expand +Emit a warning message if any pseudo-instruction expansions occurred. +For example, a @code{or} instruction with an immediate larger than 16-bits +will be expanded into two instructions. This is a very undesirable feature to +rely on, so this flag can help detect any code where it happens. One +use of it, for instance, has been to find and eliminate any place +where @code{gcc} may emit these pseudo-instructions. +@item -mxp +Enable support for the i860XP instructions and control registers. By default, +this option is disabled so that only the base instruction set (i.e., i860XR) +is supported. +@item -mintel-syntax +The i860 assembler defaults to AT&T/SVR4 syntax. This option enables the +Intel syntax. +@end table + +@node Directives-i860 +@section i860 Machine Directives + +@cindex machine directives, i860 +@cindex i860 machine directives + +@table @code +@cindex @code{dual} directive, i860 +@item .dual +Enter dual instruction mode. While this directive is supported, the +preferred way to use dual instruction mode is to explicitly code +the dual bit with the @code{d.} prefix. +@end table + +@table @code +@cindex @code{enddual} directive, i860 +@item .enddual +Exit dual instruction mode. While this directive is supported, the +preferred way to use dual instruction mode is to explicitly code +the dual bit with the @code{d.} prefix. +@end table + +@table @code +@cindex @code{atmp} directive, i860 +@item .atmp +Change the temporary register used when expanding pseudo operations. The +default register is @code{r31}. +@end table + +The @code{.dual}, @code{.enddual}, and @code{.atmp} directives are available only in the Intel syntax mode. + +Both syntaxes allow for the standard @code{.align} directive. However, +the Intel syntax additionally allows keywords for the alignment +parameter: "@code{.align type}", where `type' is one of @code{.short}, @code{.long}, +@code{.quad}, @code{.single}, @code{.double} representing alignments of 2, 4, +16, 4, and 8, respectively. + +@node Opcodes for i860 +@section i860 Opcodes + +@cindex opcodes, i860 +@cindex i860 opcodes +All of the Intel i860XR and i860XP machine instructions are supported. Please see +either @emph{i860 Microprocessor Programmer's Reference Manual} or @emph{i860 Microprocessor Architecture} for more information. +@subsection Other instruction support (pseudo-instructions) +For compatibility with some other i860 assemblers, a number of +pseudo-instructions are supported. While these are supported, they are +a very undesirable feature that should be avoided -- in particular, when +they result in an expansion to multiple actual i860 instructions. Below +are the pseudo-instructions that result in expansions. +@itemize @bullet +@item Load large immediate into general register: + +The pseudo-instruction @code{mov imm,%rn} (where the immediate does +not fit within a signed 16-bit field) will be expanded into: +@smallexample +orh large_imm@@h,%r0,%rn +or large_imm@@l,%rn,%rn +@end smallexample +@item Load/store with relocatable address expression: + +For example, the pseudo-instruction @code{ld.b addr_exp(%rx),%rn} +will be expanded into: +@smallexample +orh addr_exp@@ha,%rx,%r31 +ld.l addr_exp@@l(%r31),%rn +@end smallexample + +The analogous expansions apply to @code{ld.x, st.x, fld.x, pfld.x, fst.x}, and @code{pst.x} as well. +@item Signed large immediate with add/subtract: + +If any of the arithmetic operations @code{adds, addu, subs, subu} are used +with an immediate larger than 16-bits (signed), then they will be expanded. +For instance, the pseudo-instruction @code{adds large_imm,%rx,%rn} expands to: +@smallexample +orh large_imm@@h,%r0,%r31 +or large_imm@@l,%r31,%r31 +adds %r31,%rx,%rn +@end smallexample +@item Unsigned large immediate with logical operations: + +Logical operations (@code{or, andnot, or, xor}) also result in expansions. +The pseudo-instruction @code{or large_imm,%rx,%rn} results in: +@smallexample +orh large_imm@@h,%rx,%r31 +or large_imm@@l,%r31,%rn +@end smallexample + +Similarly for the others, except for @code{and} which expands to: +@smallexample +andnot (-1 - large_imm)@@h,%rx,%r31 +andnot (-1 - large_imm)@@l,%r31,%rn +@end smallexample +@end itemize + |