Add DDR options setting on MPC8641HPCN board

* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay based on board ddr frequency and n_ranks.

* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.

Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>

1 files changed, 110 insertions, 36 deletions

diff --git a/board/freescale/mpc8641hpcn/ddr.c b/board/freescale/mpc8641hpcn/ddr.c
index 23497f9..517c6ee 100644
--- a/board/freescale/mpc8641hpcn/ddr.c
+++ b/board/freescale/mpc8641hpcn/ddr.c
@@ -46,46 +46,120 @@ void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
 	}
 }
 
+typedef struct {
+        u32 datarate_mhz_low;
+        u32 datarate_mhz_high;
+        u32 n_ranks;
+        u32 clk_adjust;
+        u32 cpo;
+        u32 write_data_delay;
+} board_specific_parameters_t;
+
+/* XXX: these values need to be checked for all interleaving modes.  */
+const board_specific_parameters_t board_specific_parameters[2][16] = {
+	{
+	/* 	memory controller 0		 	*/
+	/*	  lo|  hi|  num|  clk| cpo|wrdata	*/
+	/*	 mhz| mhz|ranks|adjst|    | delay	*/
+		{  0, 333,    4,    7,   7,     3},
+		{334, 400,    4,    7,   9,     3},
+		{401, 549,    4,    7,   9,     3},
+		{550, 650,    4,    7,  10,     4},
+
+		{  0, 333,    3,    7,   7,     3},
+		{334, 400,    3,    7,   9,     3},
+		{401, 549,    3,    7,   9,     3},
+		{550, 650,    3,    7,  10,     4},
+
+		{  0, 333,    2,    7,   7,     3},
+		{334, 400,    2,    7,   9,     3},
+		{401, 549,    2,    7,   9,     3},
+		{550, 650,    2,    7,  10,     4},
+
+		{  0, 333,    1,    7,   7,     3},
+		{334, 400,    1,    7,   9,     3},
+		{401, 549,    1,    7,   9,     3},
+		{550, 650,    1,    7,  10,     4}
+	},
+
+	{
+	/* 	memory controller 1			*/
+	/*        lo|  hi|  num|  clk| cpo|wrdata	*/
+	/*       mhz| mhz|ranks|adjst|    | delay	*/
+		{  0, 333,    4,    7,   7,    3},
+		{334, 400,    4,    7,   9,    3},
+		{401, 549,    4,    7,   9,    3},
+		{550, 650,    4,    7,  10,    4},
+
+		{  0, 333,    3,    7,   7,    3},
+		{334, 400,    3,    7,   9,    3},
+		{401, 549,    3,    7,   9,    3},
+		{550, 650,    3,    7,  10,    4},
+
+		{  0, 333,    2,    7,   7,    3},
+		{334, 400,    2,    7,   9,    3},
+		{401, 549,    2,    7,   9,    3},
+		{550, 650,    2,    7,  10,    4},
+
+		{  0, 333,    1,    7,   7,    3},
+		{334, 400,    1,    7,   9,    3},
+		{401, 549,    1,    7,   9,    3},
+		{550, 650,    1,    7,  10,    4}
+	}
+};
+
 void fsl_ddr_board_options(memctl_options_t *popts,
-				dimm_params_t *pdimm,
-				unsigned int ctrl_num)
+			dimm_params_t *pdimm,
+			unsigned int ctrl_num)
 {
-	/*
-	 * Factors to consider for clock adjust:
-	 *	- number of chips on bus
-	 *	- position of slot
-	 *	- DDR1 vs. DDR2?
-	 *	- ???
-	 *
-	 * This needs to be determined on a board-by-board basis.
-	 *	0110	3/4 cycle late
-	 *	0111	7/8 cycle late
-	 */
-	popts->clk_adjust = 7;
+	const board_specific_parameters_t *pbsp =
+			&(board_specific_parameters[ctrl_num][0]);
+	u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
+			sizeof(board_specific_parameters[0][0]);
+	u32 i;
+	u32 j;
+	ulong ddr_freq;
 
-	/*
-	 * Factors to consider for CPO:
-	 *	- frequency
-	 *	- ddr1 vs. ddr2
+	/* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
+	 * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
+	 * there are two dimms in the controller, set odt_rd_cfg to 3 and
+	 * odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
 	 */
-	popts->cpo_override = 10;
-
-	/*
-	 * Factors to consider for write data delay:
-	 *	- number of DIMMs
-	 *
-	 * 1 = 1/4 clock delay
-	 * 2 = 1/2 clock delay
-	 * 3 = 3/4 clock delay
-	 * 4 = 1   clock delay
-	 * 5 = 5/4 clock delay
-	 * 6 = 3/2 clock delay
-	 */
-	popts->write_data_delay = 3;
+	for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+		if (i&1) {      /* odd CS */
+			popts->cs_local_opts[i].odt_rd_cfg = 0;
+			popts->cs_local_opts[i].odt_wr_cfg = 0;
+		} else {        /* even CS */
+			if ((CONFIG_DIMM_SLOTS_PER_CTLR == 2) &&
+				(pdimm[i/2].n_ranks != 0)) {
+				popts->cs_local_opts[i].odt_rd_cfg = 3;
+				popts->cs_local_opts[i].odt_wr_cfg = 3;
+			} else {
+				popts->cs_local_opts[i].odt_rd_cfg = 0;
+				popts->cs_local_opts[i].odt_wr_cfg = 4;
+			}
+		}
+	}
 
-	/*
-	 * Factors to consider for half-strength driver enable:
-	 *	- number of DIMMs installed
+	/* Get clk_adjust, cpo, write_data_delay, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
 	 */
-	popts->half_strength_driver_enable = 0;
+	ddr_freq = fsl_ddr_get_mem_data_rate() / 1000000;
+	for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) {
+		if (pdimm[j].n_ranks > 0) {
+			for (i = 0; i < num_params; i++) {
+				if (ddr_freq >= pbsp->datarate_mhz_low &&
+				ddr_freq <= pbsp->datarate_mhz_high &&
+				pdimm[j].n_ranks == pbsp->n_ranks) {
+					popts->clk_adjust = pbsp->clk_adjust;
+					popts->cpo_override = pbsp->cpo;
+					popts->write_data_delay =
+						pbsp->write_data_delay;
+					break;
+				}
+				pbsp++;
+			}
+		}
+	}
+
 }