* Add support for Promess ATC board

* Patch by Keith Outwater, 28 Apr 2003:
  - Miscellaneous corrections and additions to GEN860T board specific code.
  - Added GEN860_SC variant to GEN860T.
  - Miscellaneous corrections to GEN860T documentation.
  - Correct duplicate entry in U-Boot CREDITS file.
  - Add GEN860T_SC entry in MAINTAINERS file.
  - Update CREDITS file with GEN860T_SC info.

* Update Smiths Aerospace addresses in MAINTAINERS file

* Fix error handling in hush's version of "run" command

6 files changed, 569 insertions, 59 deletions

diff --git a/include/asm-ppc/cpm_8260.h b/include/asm-ppc/cpm_8260.h
index bf2e2a2..5c70603 100644
--- a/include/asm-ppc/cpm_8260.h
+++ b/include/asm-ppc/cpm_8260.h
@@ -170,7 +170,7 @@ typedef struct cpm_buf_desc {
  */
 #define PROFF_SMC1	(0)
 #define PROFF_SMC2	(64)
-
+#define PROFF_SPI	((16*1024) - 128)
 
 /* Define enough so I can at least use the serial port as a UART.
  */
@@ -737,6 +737,17 @@ typedef struct spi {
 #define SPMODE_LEN(x)	((((x)-1)&0xF)<<4)
 #define SPMODE_PM(x)	((x) &0xF)
 
+/* SPI Event/Mask register.
+*/
+#define SPI_EMASK		0x37	/* Event Mask				*/
+#define SPI_MME			0x20	/* Multi-Master Error			*/
+#define SPI_TXE			0x10	/* Transmit Error			*/
+#define SPI_BSY			0x04	/* Busy					*/
+#define SPI_TXB			0x02	/* Tx Buffer Empty			*/
+#define SPI_RXB			0x01	/* RX Buffer full/closed		*/
+
+#define SPI_STR			0x80	/* SPCOM: Start transmit		*/
+
 #define SPI_EB		((u_char)0x10)		/* big endian byte order */
 
 #define BD_IIC_START		((ushort)0x0400)
diff --git a/include/common.h b/include/common.h
index 5096754..2ff1c8c 100644
--- a/include/common.h
+++ b/include/common.h
@@ -198,7 +198,7 @@ extern void  pic_write (uchar reg, uchar val);
 # define CFG_DEF_EEPROM_ADDR CFG_I2C_EEPROM_ADDR
 #endif /* CONFIG_SPI || !defined(CFG_I2C_EEPROM_ADDR) */
 
-#if defined(CONFIG_PCU_E) || defined(CONFIG_CCM)
+#if defined(CONFIG_PCU_E) || defined(CONFIG_CCM) || defined(CONFIG_ATC)
 extern void spi_init_f (void);
 extern void spi_init_r (void);
 extern ssize_t spi_read  (uchar *, int, uchar *, int);
diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h
index 29e4807..47a8786 100644
--- a/include/configs/GEN860T.h
+++ b/include/configs/GEN860T.h
@@ -38,14 +38,22 @@
 /*
  * Identify the board
  */
-#define CONFIG_IDENT_STRING				" GEN860T"
+#if !defined(CONFIG_SC)
+#define CONFIG_IDENT_STRING				" B2"
+#else
+#define CONFIG_IDENT_STRING				" SC"
+#endif
 
 /*
  * Don't depend on the RTC clock to determine clock frequency -
  * the 860's internal rtc uses a 32.768 KHz clock which is
  * generated by the DS1337 - and the DS1337 clock can be turned off.
  */
-#define	CONFIG_8xx_GCLK_FREQ			66600000
+#if !defined(CONFIG_SC)
+#define	CONFIG_8xx_GCLK_FREQ			66600000 
+#else
+#define	CONFIG_8xx_GCLK_FREQ			48000000
+#endif
 
 /*
  * The RS-232 console port is on SMC1
@@ -143,7 +151,7 @@
  * environment so that we can autoscript the full default environment.
  */
 #define CONFIG_ETHADDR					9a:52:63:15:85:25
-#define CONFIG_SERVERIP					10.0.4.200
+#define CONFIG_SERVERIP					10.0.4.201
 #define CONFIG_IPADDR					10.0.4.111
 
 /*
@@ -156,17 +164,20 @@
 #define	CFG_I2C_EEPROM_ADDR_LEN			2		/* need 16 bit address	*/
 #define CFG_ENV_EEPROM_SIZE				(32 * 1024)
 
-#undef	CONFIG_HARD_I2C
-#define CONFIG_SOFT_I2C
-
 /*
- * Configure software I2C support (taken from IP860 BSP).
- * The I2C bus is connected to the GEN860T's 'dedicated' I2C
- * pins, i.e. PB26 and PB27
+ * Enable I2C and select the hardware/software driver
  */
+#define CONFIG_HARD_I2C		1				/* CPM based I2C			*/
+#undef	CONFIG_SOFT_I2C        				/* Bit-banged I2C			*/
+
+#ifdef CONFIG_HARD_I2C
+#define	CFG_I2C_SPEED		100000			/* clock speed in Hz		*/
+#define CFG_I2C_SLAVE		0xFE			/* I2C slave address		*/
+#endif
+
+#ifdef CONFIG_SOFT_I2C
 #define PB_SCL				0x00000020		/* PB 26					*/
 #define PB_SDA				0x00000010		/* PB 27 					*/
-
 #define I2C_INIT			(immr->im_cpm.cp_pbdir |=  PB_SCL)
 #define I2C_ACTIVE			(immr->im_cpm.cp_pbdir |=  PB_SDA)
 #define I2C_TRISTATE		(immr->im_cpm.cp_pbdir &= ~PB_SDA)
@@ -176,15 +187,14 @@
 #define I2C_SCL(bit)		if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 								else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY			udelay(5)		/* 1/4 I2C clock duration	*/
-
-#define	CFG_I2C_SPEED		100000			/* clock speed in Hz		*/
-#define CFG_I2C_SLAVE		0xFE			/* I2C slave address		*/
+#endif
 
 /*
  * Allow environment overwrites by anyone
  */
 #define CONFIG_ENV_OVERWRITE
 
+#if !defined(CONFIG_SC)
 /*
  * The MPC860's internal RTC is horribly broken in rev D masks. Three
  * internal MPC860T circuit nodes were inadvertently left floating; this
@@ -193,35 +203,55 @@
  * reasonable battery can keep that kind RTC running during powerdown for any
  * length of time, so we use an external RTC on the I2C bus instead.
  */
-#undef	CONFIG_RTC_MPC8xx
 #define CONFIG_RTC_DS1337
-#define CFG_I2C_RTC_ADDR				0x68
+#define CFG_I2C_RTC_ADDR				0x68 
 
+#else
 /*
- * Allow partial commands to be matched to uniqueness.
+ * No external RTC on SC variant, so we're stuck with the internal one.
  */
-#define CFG_MATCH_PARTIAL_CMD
+#define	CONFIG_RTC_MPC8xx
+#endif
+
+/*
+ * Power On Self Test support
+ */
+#define CONFIG_POST			  ( CFG_POST_CACHE		| \
+								CFG_POST_MEMORY		| \
+								CFG_POST_CPU		| \
+								CFG_POST_UART		| \
+								CFG_POST_SPR )
+
+#ifdef CONFIG_POST
+#define CFG_CMD_POST_DIAG CFG_CMD_DIAG
+#else
+#define CFG_CMD_POST_DIAG		0
+#endif
 
 /*
  * List of available monitor commands.  Use the system default list
  * plus add some of the "non-standard" commands back in.
  * See ./cmd_confdefs.h
  */
-#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
+#define BASE_CONFIG_COMMANDS	( CONFIG_CMD_DFL	| \
 								CFG_CMD_ASKENV	| \
 								CFG_CMD_DHCP	| \
 								CFG_CMD_I2C		| \
-								CFG_CMD_DOC		| \
 								CFG_CMD_EEPROM	| \
 								CFG_CMD_REGINFO	| \
 								CFG_CMD_IMMAP	| \
 								CFG_CMD_ELF		| \
 								CFG_CMD_DATE	| \
-								CFG_CMD_DATE	| \
 								CFG_CMD_FPGA	| \
 								CFG_CMD_MII 	| \
-								CFG_CMD_BEDBUG	\
-						      )
+								CFG_CMD_BEDBUG	| \
+								CFG_CMD_POST_DIAG )
+
+#if !defined(CONFIG_SC)
+#define	CONFIG_COMMANDS ( BASE_CONFIG_COMMANDS | CFG_CMD_DOC ) 
+#else
+#define CONFIG_COMMANDS	BASE_CONFIG_COMMANDS
+#endif
 
 /*
  * There is no IDE/PCMCIA hardware support on the board.
@@ -258,7 +288,12 @@
  * Verbose help from command monitor.
  */
 #define	CFG_LONGHELP
-#define	CFG_PROMPT			"gen860t> "
+#if !defined(CONFIG_SC)
+#define	CFG_PROMPT			"B2> "
+#else
+#define	CFG_PROMPT			"SC> "
+#endif
+
 
 /*
  * Use the "hush" command parser
@@ -393,15 +428,9 @@
 /*
  * Reserve memory for U-Boot.
  */
-#define CFG_MAX_U_BOOT_SECT	3
-
-#if defined(DEBUG)
-#define	CFG_MONITOR_LEN		(512 * 1024)
-#else
-#define	CFG_MONITOR_LEN		(256 * 1024)
-#endif
-
-#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define CFG_MAX_UBOOT_SECTS		4
+#define	CFG_MONITOR_LEN			(CFG_MAX_UBOOT_SECTS * CFG_FLASH_SECT_SIZE)
+#define CFG_MONITOR_BASE		CFG_FLASH_BASE
 
 /*
  * Select environment placement.  NOTE that u-boot.lds must
@@ -414,8 +443,14 @@
 #define CFG_ENV_SIZE			(2 * 1024)
 #define CFG_ENV_OFFSET			(CFG_ENV_EEPROM_SIZE - (8 * 1024))
 #else
-#define CFG_ENV_SIZE			(4 * 1024)
-#define CFG_ENV_OFFSET			(CFG_MAX_U_BOOT_SECT * CFG_FLASH_SECT_SIZE)
+#define CFG_ENV_SIZE			0x1000
+#define CFG_ENV_SECT_SIZE		CFG_FLASH_SECT_SIZE
+
+/*
+ * This ultimately gets passed right into the linker script, so we have to
+ * use a number :(
+ */
+#define CFG_ENV_OFFSET			0x060000
 #endif
 
 /*
@@ -439,7 +474,7 @@
 #endif
 
 /*------------------------------------------------------------------------
- * SYPCR - System Protection Control				UM 11-9
+ * SYPCR - System Protection Control							UM 11-9
  * -----------------------------------------------------------------------
  * SYPCR can only be written once after reset!
  *
@@ -523,6 +558,7 @@
  */
 #define SCCR_MASK   SCCR_EBDF11
 
+#if !defined(CONFIG_SC)
 #define CFG_SCCR	( SCCR_TBS			| 	/* timebase = GCLK/2	*/ \
 					  SCCR_COM00   		| 	/* full strength CLKOUT	*/ \
 					  SCCR_DFSYNC00 	| 	/* SYNCLK / 1 (normal)	*/ \
@@ -530,6 +566,17 @@
 					  SCCR_DFNL000		| \
 					  SCCR_DFNH000		  \
 					)
+#else
+#define CFG_SCCR	( SCCR_TBS			| 	/* timebase = GCLK/2	*/ \
+					  SCCR_COM00   		| 	/* full strength CLKOUT	*/ \
+					  SCCR_DFSYNC00 	| 	/* SYNCLK / 1 (normal)	*/ \
+					  SCCR_DFBRG00		| 	/* BRGCLK / 1 (normal)	*/ \
+					  SCCR_DFNL000		| \
+					  SCCR_DFNH000		| \
+					  SCCR_RTDIV		| \
+					  SCCR_RTSEL		  \
+					)
+#endif
 
 /*-----------------------------------------------------------------------
  * DER - Debug Enable Register									UM 37-46
@@ -695,10 +742,12 @@
 /*
  * Disk On Chip (millenium) configuration
  */
+#if !defined(CONFIG_SC)
 #define CFG_MAX_DOC_DEVICE	1
 #undef	CFG_DOC_SUPPORT_2000
 #define CFG_DOC_SUPPORT_MILLENNIUM
 #undef	CFG_DOC_PASSIVE_PROBE
+#endif
 
 /*
  * FEC interrupt assignment
diff --git a/include/configs/TQM8260.h b/include/configs/TQM8260.h
index 86281dd..1ea9a5e 100644
--- a/include/configs/TQM8260.h
+++ b/include/configs/TQM8260.h
@@ -203,11 +203,15 @@
 
 
 /* system clock rate (CLKIN) - equal to the 60x and local bus speed */
-#ifndef CONFIG_300MHz
-#define CONFIG_8260_CLKIN	66666666	/* in Hz */
-#else
-#define CONFIG_8260_CLKIN	83333000	/* in Hz */
-#endif
+#ifdef CONFIG_MPC8255
+#  define CONFIG_8260_CLKIN	66666666	/* in Hz */
+#else	/* !CONFIG_MPC8255 */
+# ifndef CONFIG_300MHz
+#  define CONFIG_8260_CLKIN	66666666	/* in Hz */
+# else
+#  define CONFIG_8260_CLKIN	83333000	/* in Hz */
+# endif
+#endif	/* CONFIG_MPC8255 */
 
 #if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
 #define CONFIG_BAUDRATE		230400
@@ -311,15 +315,19 @@
  * defines for the various registers affected by the HRCW e.g. changing
  * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
  */
-#if defined(CONFIG_266MHz)
-#define CFG_HRCW_MASTER		(HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \
-				 HRCW_MODCK_H0111)
-#elif defined(CONFIG_300MHz)
-#define CFG_HRCW_MASTER		(HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \
-				 HRCW_MODCK_H0110)
-#else
-#define CFG_HRCW_MASTER		(HRCW_CIP | HRCW_ISB111 | HRCW_BMS)
-#endif
+#define	__HRCW__ALL__		(HRCW_CIP | HRCW_ISB111 | HRCW_BMS)
+
+#ifdef	CONFIG_MPC8255
+#  define CFG_HRCW_MASTER	(__HRCW__ALL__ | HRCW_MODCK_H0111)
+#else	/* ! MPC8255 */
+# if defined(CONFIG_266MHz)
+#  define CFG_HRCW_MASTER	(__HRCW__ALL__ | HRCW_MODCK_H0111)
+# elif defined(CONFIG_300MHz)
+#  define CFG_HRCW_MASTER	(__HRCW__ALL__ | HRCW_MODCK_H0110)
+# else
+#  define CFG_HRCW_MASTER	(__HRCW__ALL__)
+# endif
+#endif	/* CONFIG_MPC8255 */
 
 /* no slaves so just fill with zeros */
 #define CFG_HRCW_SLAVE1		0
diff --git a/include/configs/atc.h b/include/configs/atc.h
new file mode 100644
index 0000000..ca6b740
--- /dev/null
+++ b/include/configs/atc.h
@@ -0,0 +1,442 @@
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC8260		1	/* This is an MPC8260 CPU		*/
+#define CONFIG_ATC		1	/* ...on a ATC board	*/
+
+/*
+ * select serial console configuration
+ *
+ * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ *
+ * if CONFIG_CONS_NONE is defined, then the serial console routines must
+ * defined elsewhere (for example, on the cogent platform, there are serial
+ * ports on the motherboard which are used for the serial console - see
+ * cogent/cma101/serial.[ch]).
+ */
+#define  CONFIG_CONS_ON_SMC		/* define if console on SMC */
+#undef CONFIG_CONS_ON_SCC		/* define if console on SCC */
+#undef  CONFIG_CONS_NONE		/* define if console on something else*/
+#define CONFIG_CONS_INDEX	2	/* which serial channel for console */
+
+#define CONFIG_BAUDRATE		115200
+
+/*
+ * select ethernet configuration
+ *
+ * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
+ * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
+ * for FCC)
+ *
+ * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
+ * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
+ * from CONFIG_COMMANDS to remove support for networking.
+ *
+ */
+#undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC       */
+#undef	CONFIG_ETHER_NONE		/* define if ether on something else */
+#define CONFIG_ETHER_ON_FCC
+
+#define	CONFIG_NET_MULTI
+#define CONFIG_ETHER_ON_FCC2
+
+/*
+ * - Rx-CLK is CLK13
+ * - Tx-CLK is CLK14
+ * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
+ * - Enable Full Duplex in FSMR
+ */
+# define CFG_CMXFCR_MASK2	(CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
+# define CFG_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+# define CFG_CPMFCR_RAMTYPE	0
+# define CFG_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
+
+#define CONFIG_ETHER_ON_FCC3
+
+/*
+ * - Rx-CLK is CLK15
+ * - Tx-CLK is CLK16
+ * - RAM for BD/Buffers is on the local Bus (see 28-13)
+ * - Enable Half Duplex in FSMR
+ */
+# define CFG_CMXFCR_MASK3	(CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
+# define CFG_CMXFCR_VALUE3	(CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
+
+/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
+#define CONFIG_8260_CLKIN	64000000	/* in Hz */
+
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+
+#undef	CONFIG_CLOCKS_IN_MHZ		/* clocks passsed to Linux in Hz */
+
+#define CONFIG_PREBOOT							\
+	"echo;"								\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;"\
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND						\
+	"bootp;"							\
+	"setenv bootargs root=/dev/nfs rw "				\
+	"nfsroot=$(serverip):$(rootpath) " 				\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"\
+	"bootm"
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configuration options
+ */
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_COMMANDS		(CONFIG_CMD_DFL | CFG_CMD_EEPROM)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP			/* undef to save memory		*/
+#define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define	CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END	0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define	CFG_LOAD_ADDR	0x100000	/* default load address	*/
+
+#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#define	CFG_RESET_ADDRESS 0xFFF00100	/* "bad" address		*/
+
+#define CFG_ALLOC_DPRAM
+
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#define CONFIG_SPI
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * Flash configuration
+ */
+
+#define CFG_BOOTROM_BASE	0xFF800000
+#define CFG_BOOTROM_SIZE	0x00080000
+#define CFG_FLASH_BASE		0xFF000000
+#define CFG_FLASH_SIZE		0x00800000
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max num of memory banks      */
+#define CFG_MAX_FLASH_SECT	128	/* max num of sects on one chip */
+
+#define CFG_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
+#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
+
+#define CONFIG_FLASH_16BIT
+
+/*-----------------------------------------------------------------------
+ * Hard Reset Configuration Words
+ *
+ * if you change bits in the HRCW, you must also change the CFG_*
+ * defines for the various registers affected by the HRCW e.g. changing
+ * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
+ */
+#define CFG_HRCW_MASTER		(HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \
+				 HRCW_BPS10 | HRCW_DPPC10 |\
+				 HRCW_APPC10)
+
+/* no slaves so just fill with zeros */
+#define CFG_HRCW_SLAVE1		0
+#define CFG_HRCW_SLAVE2		0
+#define CFG_HRCW_SLAVE3		0
+#define CFG_HRCW_SLAVE4		0
+#define CFG_HRCW_SLAVE5		0
+#define CFG_HRCW_SLAVE6		0
+#define CFG_HRCW_SLAVE7		0
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR		0xF0000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define CFG_INIT_RAM_END	0x2F00  /* End of used area in DPRAM    */
+#define CFG_GBL_DATA_SIZE	128 /* size in bytes reserved for initial data*/
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ *
+ * 60x SDRAM is mapped at CFG_SDRAM_BASE.
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_SDRAM_MAX_SIZE	0x08000000	/* max. 128 MB		*/
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()*/
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+# define CFG_RAMBOOT
+#endif
+
+#if 1
+/* environment is in Flash */
+#define CFG_ENV_IS_IN_FLASH	1
+# define CFG_ENV_ADDR		(CFG_FLASH_BASE+0x40000)
+# define CFG_ENV_SIZE		0x10000
+# define CFG_ENV_SECT_SIZE	0x10000
+#else
+#define CFG_ENV_IS_IN_EEPROM	1
+#define CFG_ENV_OFFSET		0
+#define CFG_ENV_SIZE		2048
+#define CFG_EEPROM_PAGE_WRITE_BITS	4	/* 16-byte page size	*/
+#endif
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH*/
+#define BOOTFLAG_WARM		0x02	/* Software reboot                 */
+
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE      32      /* For MPC8260 CPU              */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * HIDx - Hardware Implementation-dependent Registers                    2-11
+ *-----------------------------------------------------------------------
+ * HID0 also contains cache control - initially enable both caches and
+ * invalidate contents, then the final state leaves only the instruction
+ * cache enabled. Note that Power-On and Hard reset invalidate the caches,
+ * but Soft reset does not.
+ *
+ * HID1 has only read-only information - nothing to set.
+ */
+#define CFG_HID0_INIT   (HID0_ICE|HID0_DCE|HID0_ICFI|\
+                         HID0_DCI|HID0_IFEM|HID0_ABE)
+#define CFG_HID0_FINAL  (HID0_IFEM|HID0_ABE)
+#define CFG_HID2        0
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register                                     5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CFG_RMR         RMR_CSRE
+
+/*-----------------------------------------------------------------------
+ * BCR - Bus Configuration                                       4-25
+ *-----------------------------------------------------------------------
+ */
+#define BCR_APD01	0x10000000
+#define CFG_BCR		(BCR_APD01|BCR_ETM|BCR_LETM)	/* 8260 mode */
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration                             4-31
+ *-----------------------------------------------------------------------
+ */
+#define CFG_SIUMCR      (SIUMCR_BBD|SIUMCR_DPPC10|SIUMCR_APPC10|\
+			 SIUMCR_CS10PC00|SIUMCR_BCTLC10)
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control                             4-35
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+                         SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
+#else
+#define CFG_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+                         SYPCR_SWRI|SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control                     4-40
+ *-----------------------------------------------------------------------
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ */
+#define CFG_TMCNTSC     (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control                 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CFG_PISCR       (PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control                                   9-8
+ *-----------------------------------------------------------------------
+ * Ensure DFBRG is Divide by 16
+ */
+#define CFG_SCCR        SCCR_DFBRG01
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration                         13-7
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RCCR        0
+
+#define CFG_MIN_AM_MASK	0xC0000000
+/*-----------------------------------------------------------------------
+ * MPTPR - Memory Refresh Timer Prescaler Register              10-18
+ *-----------------------------------------------------------------------
+ */
+#define CFG_MPTPR       0x1F00
+
+/*-----------------------------------------------------------------------
+ * PSRT - Refresh Timer Register                                10-16
+ *-----------------------------------------------------------------------
+ */
+#define CFG_PSRT        0x0f
+
+/*-----------------------------------------------------------------------
+ * PSRT - SDRAM Mode Register                                   10-10
+ *-----------------------------------------------------------------------
+ */
+
+	/* SDRAM initialization values for 8-column chips
+	 */
+#define CFG_OR2_8COL	(CFG_MIN_AM_MASK		|\
+			 ORxS_BPD_4			|\
+			 ORxS_ROWST_PBI0_A10		|\
+			 ORxS_NUMR_11)
+
+#define CFG_PSDMR_8COL	(PSDMR_SDAM_A13_IS_A5		|\
+			 PSDMR_BSMA_A16_A18		|\
+			 PSDMR_SDA10_PBI0_A10		|\
+			 PSDMR_RFRC_7_CLK		|\
+			 PSDMR_PRETOACT_2W		|\
+			 PSDMR_ACTTORW_1W		|\
+			 PSDMR_LDOTOPRE_1C		|\
+			 PSDMR_WRC_1C			|\
+			 PSDMR_CL_2)
+
+	/* SDRAM initialization values for 9-column chips
+	 */
+#define CFG_OR2_9COL	(CFG_MIN_AM_MASK		|\
+			 ORxS_BPD_4			|\
+			 ORxS_ROWST_PBI0_A7		|\
+			 ORxS_NUMR_13)
+
+#define CFG_PSDMR_9COL	(PSDMR_SDAM_A14_IS_A5		|\
+			 PSDMR_BSMA_A13_A15		|\
+			 PSDMR_SDA10_PBI0_A9		|\
+			 PSDMR_RFRC_7_CLK		|\
+			 PSDMR_PRETOACT_2W		|\
+			 PSDMR_ACTTORW_1W		|\
+			 PSDMR_LDOTOPRE_1C		|\
+			 PSDMR_WRC_1C			|\
+			 PSDMR_CL_2)
+
+/*
+ * Init Memory Controller:
+ *
+ * Bank Bus     Machine PortSz  Device
+ * ---- ---     ------- ------  ------
+ *  0   60x     GPCM    8  bit  Boot ROM
+ *  1   60x     GPCM    64 bit  FLASH
+ *  2   60x     SDRAM   64 bit  SDRAM
+ *
+ */
+
+#define CFG_MRS_OFFS	0x00000000
+
+/* Bank 0 - FLASH
+ */
+#define CFG_BR0_PRELIM  ((CFG_FLASH_BASE & BRx_BA_MSK)  |\
+                         BRx_PS_16                      |\
+                         BRx_MS_GPCM_P                  |\
+                         BRx_V)
+
+#define CFG_OR0_PRELIM  (P2SZ_TO_AM(CFG_FLASH_SIZE)     |\
+                         ORxG_CSNT                      |\
+                         ORxG_ACS_DIV1                  |\
+                         ORxG_SCY_3_CLK                 |\
+                         ORxU_EHTR_8IDLE)
+
+
+/* Bank 2 - 60x bus SDRAM
+ */
+#ifndef CFG_RAMBOOT
+#define CFG_BR2_PRELIM  ((CFG_SDRAM_BASE & BRx_BA_MSK)  |\
+                         BRx_PS_64                      |\
+                         BRx_MS_SDRAM_P                 |\
+                         BRx_V)
+
+#define CFG_OR2_PRELIM	 CFG_OR2_8COL
+
+#define CFG_PSDMR	 CFG_PSDMR_8COL
+#endif /* CFG_RAMBOOT */
+
+#endif	/* __CONFIG_H */
diff --git a/include/status_led.h b/include/status_led.h
index 773573d..0d5a56e 100644
--- a/include/status_led.h
+++ b/include/status_led.h
@@ -97,20 +97,20 @@ void status_led_set  (int led, int state);
 # define STATUS_LED_DAT			im_ioport.iop_padat
 
 # define STATUS_LED_BIT			0x0800	/* Red LED 0 is on PA.4	*/
-# define STATUS_LED_PERIOD		(CFG_HZ / 2)
-# define STATUS_LED_STATE		STATUS_LED_BLINKING
+# define STATUS_LED_PERIOD		(CFG_HZ / 4)
+# define STATUS_LED_STATE		STATUS_LED_OFF
 # define STATUS_LED_BIT1		0x0400	/* Grn LED 1 is on PA.5	*/
-# define STATUS_LED_PERIOD1		(CFG_HZ / 2)
+# define STATUS_LED_PERIOD1		(CFG_HZ / 8)
 # define STATUS_LED_STATE1		STATUS_LED_BLINKING
 # define STATUS_LED_BIT2		0x0080	/* Red LED 2 is on PA.8	*/
-# define STATUS_LED_PERIOD2		(CFG_HZ / 2)
-# define STATUS_LED_STATE2		STATUS_LED_BLINKING
+# define STATUS_LED_PERIOD2		(CFG_HZ / 4)
+# define STATUS_LED_STATE2		STATUS_LED_OFF
 # define STATUS_LED_BIT3		0x0040	/* Grn LED 3 is on PA.9	*/
-# define STATUS_LED_PERIOD3		(CFG_HZ / 2)
-# define STATUS_LED_STATE3		STATUS_LED_BLINKING
+# define STATUS_LED_PERIOD3		(CFG_HZ / 4)
+# define STATUS_LED_STATE3		STATUS_LED_OFF
 
 # define STATUS_LED_ACTIVE		1	/* LED on for bit == 1	*/
-# define STATUS_LED_BOOT		0	/* Boot status on LED 1	*/
+# define STATUS_LED_BOOT		1	/* Boot status on LED 1	*/
 
 /*****  IVMS8  **********************************************************/
 #elif defined(CONFIG_IVMS8)