diff options
Diffstat (limited to 'arch/ppc/cpu/mpc85xx/release.S')
| -rw-r--r-- | arch/ppc/cpu/mpc85xx/release.S | 311 |
1 files changed, 311 insertions, 0 deletions
diff --git a/arch/ppc/cpu/mpc85xx/release.S b/arch/ppc/cpu/mpc85xx/release.S new file mode 100644 index 0000000..0b5b9da --- /dev/null +++ b/arch/ppc/cpu/mpc85xx/release.S @@ -0,0 +1,311 @@ +/* + * Copyright 2008-2010 Freescale Semiconductor, Inc. + * Kumar Gala <kumar.gala@freescale.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> +#include <mpc85xx.h> +#include <version.h> + +#define _LINUX_CONFIG_H 1 /* avoid reading Linux autoconf.h file */ + +#include <ppc_asm.tmpl> +#include <ppc_defs.h> + +#include <asm/cache.h> +#include <asm/mmu.h> + +/* To boot secondary cpus, we need a place for them to start up. + * Normally, they start at 0xfffffffc, but that's usually the + * firmware, and we don't want to have to run the firmware again. + * Instead, the primary cpu will set the BPTR to point here to + * this page. We then set up the core, and head to + * start_secondary. Note that this means that the code below + * must never exceed 1023 instructions (the branch at the end + * would then be the 1024th). + */ + .globl __secondary_start_page + .align 12 +__secondary_start_page: +/* First do some preliminary setup */ + lis r3, HID0_EMCP@h /* enable machine check */ +#ifndef CONFIG_E500MC + ori r3,r3,HID0_TBEN@l /* enable Timebase */ +#endif +#ifdef CONFIG_PHYS_64BIT + ori r3,r3,HID0_ENMAS7@l /* enable MAS7 updates */ +#endif + mtspr SPRN_HID0,r3 + +#ifndef CONFIG_E500MC + li r3,(HID1_ASTME|HID1_ABE)@l /* Addr streaming & broadcast */ + mfspr r0,PVR + andi. r0,r0,0xff + cmpwi r0,0x50@l /* if we are rev 5.0 or greater set MBDD */ + blt 1f + /* Set MBDD bit also */ + ori r3, r3, HID1_MBDD@l +1: + mtspr SPRN_HID1,r3 +#endif + + /* Enable branch prediction */ + lis r3,BUCSR_ENABLE@h + ori r3,r3,BUCSR_ENABLE@l + mtspr SPRN_BUCSR,r3 + + /* Ensure TB is 0 */ + li r3,0 + mttbl r3 + mttbu r3 + + /* Enable/invalidate the I-Cache */ + lis r2,(L1CSR1_ICFI|L1CSR1_ICLFR)@h + ori r2,r2,(L1CSR1_ICFI|L1CSR1_ICLFR)@l + mtspr SPRN_L1CSR1,r2 +1: + mfspr r3,SPRN_L1CSR1 + and. r1,r3,r2 + bne 1b + + lis r3,(L1CSR1_CPE|L1CSR1_ICE)@h + ori r3,r3,(L1CSR1_CPE|L1CSR1_ICE)@l + mtspr SPRN_L1CSR1,r3 + isync +2: + mfspr r3,SPRN_L1CSR1 + andi. r1,r3,L1CSR1_ICE@l + beq 2b + + /* Enable/invalidate the D-Cache */ + lis r2,(L1CSR0_DCFI|L1CSR0_DCLFR)@h + ori r2,r2,(L1CSR0_DCFI|L1CSR0_DCLFR)@l + mtspr SPRN_L1CSR0,r2 +1: + mfspr r3,SPRN_L1CSR0 + and. r1,r3,r2 + bne 1b + + lis r3,(L1CSR0_CPE|L1CSR0_DCE)@h + ori r3,r3,(L1CSR0_CPE|L1CSR0_DCE)@l + mtspr SPRN_L1CSR0,r3 + isync +2: + mfspr r3,SPRN_L1CSR0 + andi. r1,r3,L1CSR0_DCE@l + beq 2b + +#define toreset(x) (x - __secondary_start_page + 0xfffff000) + + /* get our PIR to figure out our table entry */ + lis r3,toreset(__spin_table)@h + ori r3,r3,toreset(__spin_table)@l + + /* r10 has the base address for the entry */ + mfspr r0,SPRN_PIR +#ifdef CONFIG_E500MC + rlwinm r4,r0,27,27,31 +#else + mr r4,r0 +#endif + slwi r8,r4,5 + add r10,r3,r8 + +#if defined(CONFIG_E500MC) && defined(CONFIG_SYS_CACHE_STASHING) + /* set stash id to (coreID) * 2 + 32 + L1 CT (0) */ + slwi r8,r4,1 + addi r8,r8,32 + mtspr L1CSR2,r8 +#endif + +#ifdef CONFIG_BACKSIDE_L2_CACHE + /* Enable/invalidate the L2 cache */ + msync + lis r2,(L2CSR0_L2FI|L2CSR0_L2LFC)@h + ori r2,r2,(L2CSR0_L2FI|L2CSR0_L2LFC)@l + mtspr SPRN_L2CSR0,r2 +1: + mfspr r3,SPRN_L2CSR0 + and. r1,r3,r2 + bne 1b + +#ifdef CONFIG_SYS_CACHE_STASHING + /* set stash id to (coreID) * 2 + 32 + L2 (1) */ + addi r3,r8,1 + mtspr SPRN_L2CSR1,r3 +#endif + + lis r3,CONFIG_SYS_INIT_L2CSR0@h + ori r3,r3,CONFIG_SYS_INIT_L2CSR0@l + mtspr SPRN_L2CSR0,r3 + isync +2: + mfspr r3,SPRN_L2CSR0 + andis. r1,r3,L2CSR0_L2E@h + beq 2b +#endif + +#define EPAPR_MAGIC (0x45504150) +#define ENTRY_ADDR_UPPER 0 +#define ENTRY_ADDR_LOWER 4 +#define ENTRY_R3_UPPER 8 +#define ENTRY_R3_LOWER 12 +#define ENTRY_RESV 16 +#define ENTRY_PIR 20 +#define ENTRY_R6_UPPER 24 +#define ENTRY_R6_LOWER 28 +#define ENTRY_SIZE 32 + + /* setup the entry */ + li r3,0 + li r8,1 + stw r0,ENTRY_PIR(r10) + stw r3,ENTRY_ADDR_UPPER(r10) + stw r8,ENTRY_ADDR_LOWER(r10) + stw r3,ENTRY_R3_UPPER(r10) + stw r4,ENTRY_R3_LOWER(r10) + stw r3,ENTRY_R6_UPPER(r10) + stw r3,ENTRY_R6_LOWER(r10) + + /* load r13 with the address of the 'bootpg' in SDRAM */ + lis r13,toreset(__bootpg_addr)@h + ori r13,r13,toreset(__bootpg_addr)@l + lwz r13,0(r13) + + /* setup mapping for AS = 1, and jump there */ + lis r11,(MAS0_TLBSEL(1)|MAS0_ESEL(1))@h + mtspr SPRN_MAS0,r11 + lis r11,(MAS1_VALID|MAS1_IPROT)@h + ori r11,r11,(MAS1_TS|MAS1_TSIZE(BOOKE_PAGESZ_4K))@l + mtspr SPRN_MAS1,r11 + oris r11,r13,(MAS2_I|MAS2_G)@h + ori r11,r13,(MAS2_I|MAS2_G)@l + mtspr SPRN_MAS2,r11 + oris r11,r13,(MAS3_SX|MAS3_SW|MAS3_SR)@h + ori r11,r13,(MAS3_SX|MAS3_SW|MAS3_SR)@l + mtspr SPRN_MAS3,r11 + tlbwe + + bl 1f +1: mflr r11 + /* + * OR in 0xfff to create a mask of the bootpg SDRAM address. We use + * this mask to fixup the cpu spin table and the address that we want + * to jump to, eg change them from 0xfffffxxx to 0x7ffffxxx if the + * bootpg is at 0x7ffff000 in SDRAM. + */ + ori r13,r13,0xfff + and r11, r11, r13 + and r10, r10, r13 + + addi r11,r11,(2f-1b) + mfmsr r13 + ori r12,r13,MSR_IS|MSR_DS@l + + mtspr SPRN_SRR0,r11 + mtspr SPRN_SRR1,r12 + rfi + + /* spin waiting for addr */ +2: + lwz r4,ENTRY_ADDR_LOWER(r10) + andi. r11,r4,1 + bne 2b + isync + + /* setup IVORs to match fixed offsets */ +#include "fixed_ivor.S" + + /* get the upper bits of the addr */ + lwz r11,ENTRY_ADDR_UPPER(r10) + + /* setup branch addr */ + mtspr SPRN_SRR0,r4 + + /* mark the entry as released */ + li r8,3 + stw r8,ENTRY_ADDR_LOWER(r10) + + /* mask by ~64M to setup our tlb we will jump to */ + rlwinm r12,r4,0,0,5 + + /* setup r3, r4, r5, r6, r7, r8, r9 */ + lwz r3,ENTRY_R3_LOWER(r10) + li r4,0 + li r5,0 + lwz r6,ENTRY_R6_LOWER(r10) + lis r7,(64*1024*1024)@h + li r8,0 + li r9,0 + + /* load up the pir */ + lwz r0,ENTRY_PIR(r10) + mtspr SPRN_PIR,r0 + mfspr r0,SPRN_PIR + stw r0,ENTRY_PIR(r10) + + mtspr IVPR,r12 +/* + * Coming here, we know the cpu has one TLB mapping in TLB1[0] + * which maps 0xfffff000-0xffffffff one-to-one. We set up a + * second mapping that maps addr 1:1 for 64M, and then we jump to + * addr + */ + lis r10,(MAS0_TLBSEL(1)|MAS0_ESEL(0))@h + mtspr SPRN_MAS0,r10 + lis r10,(MAS1_VALID|MAS1_IPROT)@h + ori r10,r10,(MAS1_TSIZE(BOOKE_PAGESZ_64M))@l + mtspr SPRN_MAS1,r10 + /* WIMGE = 0b00000 for now */ + mtspr SPRN_MAS2,r12 + ori r12,r12,(MAS3_SX|MAS3_SW|MAS3_SR) + mtspr SPRN_MAS3,r12 +#ifdef CONFIG_ENABLE_36BIT_PHYS + mtspr SPRN_MAS7,r11 +#endif + tlbwe + +/* Now we have another mapping for this page, so we jump to that + * mapping + */ + mtspr SPRN_SRR1,r13 + rfi + + /* + * Allocate some space for the SDRAM address of the bootpg. + * This variable has to be in the boot page so that it can + * be accessed by secondary cores when they come out of reset. + */ + .globl __bootpg_addr +__bootpg_addr: + .long 0 + + .align L1_CACHE_SHIFT + .globl __spin_table +__spin_table: + .space CONFIG_MAX_CPUS*ENTRY_SIZE + + /* Fill in the empty space. The actual reset vector is + * the last word of the page */ +__secondary_start_code_end: + .space 4092 - (__secondary_start_code_end - __secondary_start_page) +__secondary_reset_vector: + b __secondary_start_page |