diff options
Diffstat (limited to 'include/configs/TQM85xx.h')
| -rw-r--r-- | include/configs/TQM85xx.h | 380 |
1 files changed, 314 insertions, 66 deletions
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index fca5f74..d18f234 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -1,4 +1,7 @@ /* + * (C) Copyright 2007 + * Thomas Waehner, TQ-System GmbH, thomas.waehner@tqs.de. + * * (C) Copyright 2005 * Stefan Roese, DENX Software Engineering, sr@denx.de. * @@ -27,7 +30,7 @@ */ /* - * TQM85xx (8560/40/55/41) board configuration file + * TQM85xx (8560/40/55/41/48) board configuration file */ #ifndef __CONFIG_H @@ -39,25 +42,53 @@ #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */ #define CONFIG_PCI +#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ +#define CONFIG_PCIX_CHECK /* PCIX olny works at 66 MHz */ +#ifdef CONFIG_TQM8548 +#define CONFIG_PCI1 +#define CONFIG_PCIE1 +#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ +#endif + #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ + /* + * Configuration for big NOR Flashes + * + * Define CONFIG_TQM_BIGFLASH for boards with more than 128 MiB NOR Flash. + * Please be aware, that this changes the whole memory map (new CCSRBAR + * address, etc). You have to use an adapted Linux kernel or FDT blob + * if this option is set. + */ +#undef CONFIG_TQM_BIGFLASH + +/* + * NAND flash support (disabled by default) + * + * Warning: NAND support will likely increase the U-Boot image size + * to more than 256 KB. Please adjust TEXT_BASE if necessary. + */ +#undef CONFIG_NAND + /* - * Only MPC8540 doesn't have CPM module + * MPC8540 and MPC8548 don't have CPM module */ -#ifndef CONFIG_MPC8540 +#if !defined(CONFIG_MPC8540) && !defined(CONFIG_MPC8548) #define CONFIG_CPM2 1 /* has CPM2 */ #endif -#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ + +#undef CONFIG_CAN_DRIVER /* CAN Driver support */ /* * sysclk for MPC85xx * * Two valid values are: - * 33000000 - * 66000000 + * 33333333 + * 66666666 * * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz * is likely the desired value here, so that is now the default. @@ -88,10 +119,18 @@ * actual resources get mapped (not physical addresses) */ #define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ +#ifdef CONFIG_TQM_BIGFLASH +#define CFG_CCSRBAR 0xA0000000 /* relocated CCSRBAR */ +#else /* !CONFIG_TQM_BIGFLASH */ #define CFG_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ +#endif /* CONFIG_TQM_BIGFLASH */ #define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */ #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ +#define CFG_PCI1_ADDR (CFG_CCSRBAR + 0x8000) +#define CFG_PCI2_ADDR (CFG_CCSRBAR + 0x9000) +#define CFG_PCIE1_ADDR (CFG_CCSRBAR + 0xa000) + /* * DDR Setup */ @@ -102,65 +141,116 @@ /* TQM8540 & 8560 need DLL-override */ #define CONFIG_DDR_DLL /* DLL fix needed */ #define CONFIG_DDR_DEFAULT_CL 25 /* CAS latency 2,5 */ -#endif /* defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560) */ +#endif /* CONFIG_TQM8540 || CONFIG_TQM8560 */ -#if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) +#if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) || \ + defined(CONFIG_TQM8548) #define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */ -#endif /* defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) */ +#endif /* CONFIG_TQM8541 || CONFIG_TQM8555 || CONFIG_TQM8548 */ + +/* + * Old TQM85xx boards have 'M' type Spansion Flashes from the S29GLxxxM + * series while new boards have 'N' type Flashes from the S29GLxxxN + * series, which have bigger sectors: 2 x 128 instead of 2 x 64 KB. + */ +#ifdef CONFIG_TQM8548 +#define CONFIG_TQM_FLASH_N_TYPE +#endif /* CONFIG_TQM8548 */ /* * Flash on the Local Bus */ +#ifdef CONFIG_TQM_BIGFLASH +#define CFG_FLASH0 0xE0000000 +#define CFG_FLASH1 0xC0000000 +#else /* !CONFIG_TQM_BIGFLASH */ #define CFG_FLASH0 0xFC000000 #define CFG_FLASH1 0xF8000000 +#endif /* CONFIG_TQM_BIGFLASH */ #define CFG_FLASH_BANKS_LIST { CFG_FLASH1, CFG_FLASH0 } #define CFG_LBC_FLASH_BASE CFG_FLASH1 /* Localbus flash start */ -#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH */ +#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH */ +/* Default ORx timings are for <= 41.7 MHz Local Bus Clock. + * + * Note: According to timing specifications external addr latch delay + * (EAD, bit #0) must be set if Local Bus Clock is > 83 MHz. + * + * For other Local Bus Clocks see following table: + * + * Clock/MHz CFG_ORx_PRELIM + * 166 0x.....CA5 + * 133 0x.....C85 + * 100 0x.....C65 + * 83 0x.....FA2 + * 66 0x.....C82 + * 50 0x.....C60 + * 42 0x.....040 + * 33 0x.....030 + * 25 0x.....020 + * + */ +#ifdef CONFIG_TQM_BIGFLASH +#define CFG_BR0_PRELIM 0xE0001801 /* port size 32bit */ +#define CFG_OR0_PRELIM 0xE0000040 /* 512MB Flash */ +#define CFG_BR1_PRELIM 0xC0001801 /* port size 32bit */ +#define CFG_OR1_PRELIM 0xE0000040 /* 512MB Flash */ +#else /* !CONFIG_TQM_BIGFLASH */ #define CFG_BR0_PRELIM 0xfc001801 /* port size 32bit */ #define CFG_OR0_PRELIM 0xfc000040 /* 64MB Flash */ #define CFG_BR1_PRELIM 0xf8001801 /* port size 32bit */ #define CFG_OR1_PRELIM 0xfc000040 /* 64MB Flash */ +#endif /* CONFIG_TQM_BIGFLASH */ -#define CFG_FLASH_CFI /* flash is CFI compat. */ -#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver*/ +#define CFG_FLASH_CFI /* flash is CFI compat. */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */ #define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* speed up output to Flash */ -#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ -#define CFG_MAX_FLASH_SECT 512 /* sectors per device */ +#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ +#define CFG_MAX_FLASH_SECT 512 /* sectors per device */ #undef CFG_FLASH_CHECKSUM #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ -#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */ -#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ -#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ -#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ +/* + * Note: when changing the Local Bus clock divider you have to + * change the timing values in CFG_ORx_PRELIM. + * + * LCRR[00:03] CLKDIV: System (CCB) clock divider. Valid values are 2, 4, 8. + * LCRR[16:17] EADC : External address delay cycles. It should be set to 2 + * for Local Bus Clock > 83.3 MHz. + */ +#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */ +#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ +#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ +#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ #define CONFIG_L1_INIT_RAM #define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CFG_INIT_RAM_ADDR (CFG_CCSRBAR \ + + 0x04010000) /* Initial RAM address */ #define CFG_INIT_RAM_END 0x4000 /* End used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data*/ +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256kB for Mon*/ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CFG_MONITOR_LEN (~TEXT_BASE + 1)/* Reserved for Monitor */ +#define CFG_MALLOC_LEN (384 * 1024) /* Reserved for malloc */ /* Serial Port */ #if defined(CONFIG_TQM8560) -#define CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on something else */ -#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ +#define CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ -#else /* ! TQM8560 */ +#else /* !CONFIG_TQM8560 */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO @@ -173,20 +263,18 @@ #define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) /* PS/2 Keyboard */ -#if !defined(CONFIG_TQM8560) #define CONFIG_PS2KBD /* AT-PS/2 Keyboard */ #define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */ #define CONFIG_PS2SERIAL 2 /* .. on DUART2 */ #define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */ #define CONFIG_BOARD_EARLY_INIT_R 1 -#endif /* !CONFIG_TQM8560 */ #endif /* CONFIG_TQM8560 */ -#define CONFIG_BAUDRATE 115200 +#define CONFIG_BAUDRATE 115200 -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ @@ -194,11 +282,25 @@ #define CFG_PROMPT_HUSH_PS2 "> " #endif +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +/* CAN */ +#define CFG_CAN_BASE (CFG_CCSRBAR \ + + 0x03000000) /* CAN base address */ +#ifdef CONFIG_CAN_DRIVER +#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 KiB address mask */ +#define CFG_OR2_CAN (CFG_CAN_OR_AM | OR_UPM_BI) +#define CFG_BR2_CAN ((CFG_CAN_BASE & BR_BA) | \ + BR_PS_8 | BR_MS_UPMC | BR_V) +#endif /* CONFIG_CAN_DRIVER */ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ @@ -219,7 +321,7 @@ #define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ #define CFG_EEPROM_PAGE_WRITE_ENABLE #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 -#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ +#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ /* I2C SYSMON (LM75) */ #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ @@ -228,10 +330,64 @@ #define CFG_DTT_LOW_TEMP -30 #define CFG_DTT_HYSTERESIS 3 +#ifndef CONFIG_PCIE1 /* RapidIO MMU */ +#ifdef CONFIG_TQM_BIGFLASH +#define CFG_RIO_MEM_BASE 0xb0000000 /* base address */ +#define CFG_RIO_MEM_SIZE 0x10000000 /* 256M */ +#else /* !CONFIG_TQM_BIGFLASH */ #define CFG_RIO_MEM_BASE 0xc0000000 /* base address */ +#define CFG_RIO_MEM_SIZE 0x20000000 /* 512M */ +#endif /* CONFIG_TQM_BIGFLASH */ #define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE -#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */ +#endif /* CONFIG_PCIE1 */ + +/* NAND FLASH */ +#ifdef CONFIG_NAND + +#undef CFG_NAND_LEGACY + +#define CONFIG_NAND_FSL_UPM 1 + +#define CONFIG_MTD_NAND_ECC_JFFS2 1 /* use JFFS2 ECC */ + +/* address distance between chip selects */ +#define CFG_NAND_SELECT_DEVICE 1 +#define CFG_NAND_CS_DIST 0x200 + +#define CFG_NAND_SIZE 0x8000 +#define CFG_NAND0_BASE (CFG_CCSRBAR + 0x03010000) +#define CFG_NAND1_BASE (CFG_NAND0_BASE + CFG_NAND_CS_DIST) +#define CFG_NAND2_BASE (CFG_NAND1_BASE + CFG_NAND_CS_DIST) +#define CFG_NAND3_BASE (CFG_NAND2_BASE + CFG_NAND_CS_DIST) + +#define CFG_MAX_NAND_DEVICE 2 /* Max number of NAND devices */ +#define NAND_MAX_CHIPS 1 + +#if (CFG_MAX_NAND_DEVICE == 1) +#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE } +#elif (CFG_MAX_NAND_DEVICE == 2) +#define CFG_NAND_QUIET_TEST 1 +#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, \ + CFG_NAND1_BASE, \ +} +#elif (CFG_MAX_NAND_DEVICE == 4) +#define CFG_NAND_QUIET_TEST 1 +#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, \ + CFG_NAND1_BASE, \ + CFG_NAND2_BASE, \ + CFG_NAND3_BASE, \ +} +#endif + +/* CS3 for NAND Flash */ +#define CFG_BR3_PRELIM ((CFG_NAND0_BASE & BR_BA) | BR_PS_8 | \ + BR_MS_UPMB | BR_V) +#define CFG_OR3_PRELIM (P2SZ_TO_AM(CFG_NAND_SIZE) | OR_UPM_BI) + +#define NAND_BIG_DELAY_US 25 /* max tR for Samsung devices */ + +#endif /* CONFIG_NAND */ /* * General PCI @@ -240,9 +396,33 @@ #define CFG_PCI1_MEM_BASE 0x80000000 #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE #define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCI1_IO_BASE 0xe2000000 +#define CFG_PCI1_IO_BASE (CFG_CCSRBAR + 0x02000000) #define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE -#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ +#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ + +/* PCI view of System Memory */ +#define CFG_PCI_MEMORY_BUS 0x00000000 +#define CFG_PCI_MEMORY_PHYS 0x00000000 +#define CFG_PCI_MEMORY_SIZE 0x80000000 + +#ifdef CONFIG_PCIE1 +/* + * General PCI express + * Addresses are mapped 1-1. + */ +#ifdef CONFIG_TQM_BIGFLASH +#define CFG_PCIE1_MEM_BASE 0xb0000000 +#define CFG_PCIE1_MEM_SIZE 0x10000000 /* 512M */ +#define CFG_PCIE1_IO_BASE 0xaf000000 +#else /* !CONFIG_TQM_BIGFLASH */ +#define CFG_PCIE1_MEM_BASE 0xc0000000 +#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCIE1_IO_BASE 0xef000000 +#endif /* CONFIG_TQM_BIGFLASH */ +#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE +#define CFG_PCIE1_IO_PHYS CFG_PCIE1_IO_BASE +#define CFG_PCIE1_IO_SIZE 0x1000000 /* 16M */ +#endif /* CONFIG_PCIE1 */ #if defined(CONFIG_PCI) @@ -254,8 +434,7 @@ #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ -#endif /* CONFIG_PCI */ - +#endif /* CONFIG_PCI */ #define CONFIG_NET_MULTI 1 @@ -277,6 +456,27 @@ #define CONFIG_HAS_ETH1 #define CONFIG_HAS_ETH2 +#ifdef CONFIG_TQM8548 +/* + * TQM8548 has 4 ethernet ports. 4 ETSEC's. + * + * On the STK85xx Starterkit the ETSEC3/4 ports are on an + * additional adapter (AIO) between module and Starterkit. + */ +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "TSEC2" +#define CONFIG_TSEC4 1 +#define CONFIG_TSEC4_NAME "TSEC3" +#define TSEC3_PHY_ADDR 4 +#define TSEC4_PHY_ADDR 5 +#define TSEC3_PHYIDX 0 +#define TSEC4_PHYIDX 0 +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define CONFIG_HAS_ETH3 +#define CONFIG_HAS_ETH4 +#endif /* CONFIG_TQM8548 */ + /* Options are TSEC[0-1], FEC */ #define CONFIG_ETHPRIME "TSEC0" @@ -305,7 +505,7 @@ * FCC2: a - c (X50.2 - 1) */ #define CONFIG_ETHER_ON_FCC -#define CONFIG_ETHER_INDEX 1 /* FCC channel for ethernet */ +#define CONFIG_ETHER_INDEX 1 /* FCC channel for ethernet */ #endif #if defined(CONFIG_TQM8560) @@ -321,12 +521,13 @@ * FCC3: a - d (X50.2 - 3) */ #define CONFIG_ETHER_ON_FCC -#define CONFIG_ETHER_INDEX 3 /* FCC channel for ethernet */ +#define CONFIG_ETHER_INDEX 3 /* FCC channel for ethernet */ #endif #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1) #define CONFIG_ETHER_ON_FCC1 -#define CFG_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK) +#define CFG_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | \ + CMXFCR_TF1CS_MSK) #define CFG_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12) #define CFG_CPMFCR_RAMTYPE 0 #define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) @@ -334,7 +535,8 @@ #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) #define CONFIG_ETHER_ON_FCC2 -#define CFG_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) +#define CFG_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | \ + CMXFCR_TF2CS_MSK) #define CFG_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK16 | CMXFCR_TF2CS_CLK13) #define CFG_CPMFCR_RAMTYPE 0 #define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) @@ -342,7 +544,8 @@ #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3) #define CONFIG_ETHER_ON_FCC3 -#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK) +#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | \ + CMXFCR_TF3CS_MSK) #define CFG_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14) #define CFG_CPMFCR_RAMTYPE 0 #define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) @@ -352,17 +555,21 @@ * Environment */ #define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x20000) -#define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ + +#ifdef CONFIG_TQM_FLASH_N_TYPE +#define CFG_ENV_SECT_SIZE 0x40000 /* 256K (one sector) for env */ +#else /* !CONFIG_TQM_FLASH_N_TYPE */ +#define CFG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) for env */ +#endif /* CONFIG_TQM_FLASH_N_TYPE */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE 0x2000 -#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_TIMESTAMP /* Print image info with ts */ - +#define CONFIG_TIMESTAMP /* Print image info with ts */ /* * BOOTP options @@ -372,6 +579,25 @@ #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME +#ifdef CONFIG_NAND +/* + * Use NAND-FLash as JFFS2 device + */ +#define CONFIG_CMD_NAND +#define CONFIG_CMD_JFFS2 + +#define CONFIG_JFFS2_NAND 1 + +#ifdef CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT "nand0=TQM85xx-nand" +#define MTDPARTS_DEFAULT "mtdparts=TQM85xx-nand:-" +#else +#define CONFIG_JFFS2_DEV "nand0" /* NAND device jffs2 lives on */ +#define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */ +#define CONFIG_JFFS2_PART_SIZE 0x200000 /* size of jffs2 partition */ +#endif /* CONFIG_JFFS2_CMDLINE */ + +#endif /* CONFIG_NAND */ /* * Command line configuration. @@ -389,10 +615,9 @@ #define CONFIG_CMD_MII #if defined(CONFIG_PCI) - #define CONFIG_CMD_PCI +#define CONFIG_CMD_PCI #endif - #undef CONFIG_WATCHDOG /* watchdog disabled */ /* @@ -403,12 +628,13 @@ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) - #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else - #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buf Size */ +#define CFG_PBSIZE (CFG_CBSIZE + \ + sizeof(CFG_PROMPT) + 16) /* Print Buf Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ @@ -433,7 +659,6 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif - #define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/ #define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ @@ -444,10 +669,26 @@ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +/* + * Setup some board specific values for the default environment variables + */ +#ifdef CONFIG_CPM2 +#define CFG_ENV_CONSDEV "consdev=ttyCPM0\0" +#else +#define CFG_ENV_CONSDEV "consdev=ttyS0\0" +#endif +#define CFG_ENV_FDT_FILE "fdt_file="MK_STR(CONFIG_HOSTNAME)"/" \ + MK_STR(CONFIG_HOSTNAME)".dtb\0" +#define CFG_ENV_BOOTFILE "bootfile="MK_STR(CONFIG_HOSTNAME)"/uImage\0" +#define CFG_ENV_UBOOT "uboot="MK_STR(CONFIG_HOSTNAME)"/u-boot.bin\0" \ + "uboot_addr="MK_STR(TEXT_BASE)"\0" + #define CONFIG_EXTRA_ENV_SETTINGS \ - "bootfile="CFG_BOOTFILE_PATH"\0" \ + CFG_ENV_BOOTFILE \ + CFG_ENV_FDT_FILE \ + CFG_ENV_CONSDEV \ "netdev=eth0\0" \ - "consdev=ttyS0\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=$serverip:$rootpath\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ @@ -457,20 +698,27 @@ "addcons=setenv bootargs $bootargs " \ "console=$consdev,$baudrate\0" \ "flash_nfs=run nfsargs addip addcons;" \ - "bootm $kernel_addr\0" \ + "bootm $kernel_addr - $fdt_addr\0" \ "flash_self=run ramargs addip addcons;" \ - "bootm $kernel_addr $ramdisk_addr\0" \ - "net_nfs=tftp $loadaddr $bootfile;" \ - "run nfsargs addip addcons;bootm\0" \ + "bootm $kernel_addr $ramdisk_addr $fdt_addr\0" \ + "net_nfs=tftp $kernel_addr_r $bootfile;" \ + "tftp $fdt_addr_r $fdt_file;" \ + "run nfsargs addip addcons;" \ + "bootm $kernel_addr_r - $fdt_addr_r\0" \ "rootpath=/opt/eldk/ppc_85xx\0" \ - "kernel_addr=FE000000\0" \ - "ramdisk_addr=FE180000\0" \ - "load=tftp 100000 /tftpboot/$hostname/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ + "fdt_addr_r=900000\0" \ + "kernel_addr_r=1000000\0" \ + "fdt_addr=ffec0000\0" \ + "kernel_addr=ffd00000\0" \ + "ramdisk_addr=ff800000\0" \ + CFG_ENV_UBOOT \ + "load=tftp 100000 $uboot\0" \ + "update=protect off $uboot_addr +$filesize;" \ + "erase $uboot_addr +$filesize;" \ + "cp.b 100000 $uboot_addr $filesize;" \ "setenv filesize;saveenv\0" \ "upd=run load update\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" -#endif /* __CONFIG_H */ +#endif /* __CONFIG_H */ |