diff options
Diffstat (limited to 'u-boot/arch/mips/cpu/au1x00_eth.c')
| -rw-r--r-- | u-boot/arch/mips/cpu/au1x00_eth.c | 311 |
1 files changed, 311 insertions, 0 deletions
diff --git a/u-boot/arch/mips/cpu/au1x00_eth.c b/u-boot/arch/mips/cpu/au1x00_eth.c new file mode 100644 index 0000000..c510799 --- /dev/null +++ b/u-boot/arch/mips/cpu/au1x00_eth.c @@ -0,0 +1,311 @@ +/* Only eth0 supported for now + * + * (C) Copyright 2003 + * Thomas.Lange@corelatus.se + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include <config.h> + +#if defined(CONFIG_SYS_DISCOVER_PHY) +#error "PHY not supported yet" +/* We just assume that we are running 100FD for now */ +/* We all use switches, right? ;-) */ +#endif + +/* I assume ethernet behaves like au1000 */ + +#ifdef CONFIG_SOC_AU1000 +/* Base address differ between cpu:s */ +#define ETH0_BASE AU1000_ETH0_BASE +#define MAC0_ENABLE AU1000_MAC0_ENABLE +#else +#ifdef CONFIG_SOC_AU1100 +#define ETH0_BASE AU1100_ETH0_BASE +#define MAC0_ENABLE AU1100_MAC0_ENABLE +#else +#ifdef CONFIG_SOC_AU1500 +#define ETH0_BASE AU1500_ETH0_BASE +#define MAC0_ENABLE AU1500_MAC0_ENABLE +#else +#ifdef CONFIG_SOC_AU1550 +#define ETH0_BASE AU1550_ETH0_BASE +#define MAC0_ENABLE AU1550_MAC0_ENABLE +#else +#error "No valid cpu set" +#endif +#endif +#endif +#endif + +#include <common.h> +#include <malloc.h> +#include <net.h> +#include <command.h> +#include <asm/io.h> +#include <asm/au1x00.h> + +#if defined(CONFIG_CMD_MII) +#include <miiphy.h> +#endif + +/* Ethernet Transmit and Receive Buffers */ +#define DBUF_LENGTH 1520 +#define PKT_MAXBUF_SIZE 1518 + +static char txbuf[DBUF_LENGTH]; + +static int next_tx; +static int next_rx; + +/* 4 rx and 4 tx fifos */ +#define NO_OF_FIFOS 4 + +typedef struct{ + u32 status; + u32 addr; + u32 len; /* Only used for tx */ + u32 not_used; +} mac_fifo_t; + +mac_fifo_t mac_fifo[NO_OF_FIFOS]; + +#define MAX_WAIT 1000 + +#if defined(CONFIG_CMD_MII) +int au1x00_miiphy_read(const char *devname, unsigned char addr, + unsigned char reg, unsigned short * value) +{ + volatile u32 *mii_control_reg = (volatile u32*)(ETH0_BASE+MAC_MII_CNTRL); + volatile u32 *mii_data_reg = (volatile u32*)(ETH0_BASE+MAC_MII_DATA); + u32 mii_control; + unsigned int timedout = 20; + + while (*mii_control_reg & MAC_MII_BUSY) { + udelay(1000); + if (--timedout == 0) { + printf("au1x00_eth: miiphy_read busy timeout!!\n"); + return -1; + } + } + + mii_control = MAC_SET_MII_SELECT_REG(reg) | + MAC_SET_MII_SELECT_PHY(addr) | MAC_MII_READ; + + *mii_control_reg = mii_control; + + timedout = 20; + while (*mii_control_reg & MAC_MII_BUSY) { + udelay(1000); + if (--timedout == 0) { + printf("au1x00_eth: miiphy_read busy timeout!!\n"); + return -1; + } + } + *value = *mii_data_reg; + return 0; +} + +int au1x00_miiphy_write(const char *devname, unsigned char addr, + unsigned char reg, unsigned short value) +{ + volatile u32 *mii_control_reg = (volatile u32*)(ETH0_BASE+MAC_MII_CNTRL); + volatile u32 *mii_data_reg = (volatile u32*)(ETH0_BASE+MAC_MII_DATA); + u32 mii_control; + unsigned int timedout = 20; + + while (*mii_control_reg & MAC_MII_BUSY) { + udelay(1000); + if (--timedout == 0) { + printf("au1x00_eth: miiphy_write busy timeout!!\n"); + return -1; + } + } + + mii_control = MAC_SET_MII_SELECT_REG(reg) | + MAC_SET_MII_SELECT_PHY(addr) | MAC_MII_WRITE; + + *mii_data_reg = value; + *mii_control_reg = mii_control; + return 0; +} +#endif + +static int au1x00_send(struct eth_device* dev, volatile void *packet, int length){ + volatile mac_fifo_t *fifo_tx = + (volatile mac_fifo_t*)(MAC0_TX_DMA_ADDR+MAC_TX_BUFF0_STATUS); + int i; + int res; + + /* tx fifo should always be idle */ + fifo_tx[next_tx].len = length; + fifo_tx[next_tx].addr = (virt_to_phys(packet))|TX_DMA_ENABLE; + au_sync(); + + udelay(1); + i=0; + while(!(fifo_tx[next_tx].addr&TX_T_DONE)){ + if(i>MAX_WAIT){ + printf("TX timeout\n"); + break; + } + udelay(1); + i++; + } + + /* Clear done bit */ + fifo_tx[next_tx].addr = 0; + fifo_tx[next_tx].len = 0; + au_sync(); + + res = fifo_tx[next_tx].status; + + next_tx++; + if(next_tx>=NO_OF_FIFOS){ + next_tx=0; + } + return(res); +} + +static int au1x00_recv(struct eth_device* dev){ + volatile mac_fifo_t *fifo_rx = + (volatile mac_fifo_t*)(MAC0_RX_DMA_ADDR+MAC_RX_BUFF0_STATUS); + + int length; + u32 status; + + for(;;){ + if(!(fifo_rx[next_rx].addr&RX_T_DONE)){ + /* Nothing has been received */ + return(-1); + } + + status = fifo_rx[next_rx].status; + + length = status&0x3FFF; + + if(status&RX_ERROR){ + printf("Rx error 0x%x\n", status); + } + else{ + /* Pass the packet up to the protocol layers. */ + NetReceive(NetRxPackets[next_rx], length - 4); + } + + fifo_rx[next_rx].addr = (virt_to_phys(NetRxPackets[next_rx]))|RX_DMA_ENABLE; + + next_rx++; + if(next_rx>=NO_OF_FIFOS){ + next_rx=0; + } + } /* for */ + + return(0); /* Does anyone use this? */ +} + +static int au1x00_init(struct eth_device* dev, bd_t * bd){ + + volatile u32 *macen = (volatile u32*)MAC0_ENABLE; + volatile u32 *mac_ctrl = (volatile u32*)(ETH0_BASE+MAC_CONTROL); + volatile u32 *mac_addr_high = (volatile u32*)(ETH0_BASE+MAC_ADDRESS_HIGH); + volatile u32 *mac_addr_low = (volatile u32*)(ETH0_BASE+MAC_ADDRESS_LOW); + volatile u32 *mac_mcast_high = (volatile u32*)(ETH0_BASE+MAC_MCAST_HIGH); + volatile u32 *mac_mcast_low = (volatile u32*)(ETH0_BASE+MAC_MCAST_LOW); + volatile mac_fifo_t *fifo_tx = + (volatile mac_fifo_t*)(MAC0_TX_DMA_ADDR+MAC_TX_BUFF0_STATUS); + volatile mac_fifo_t *fifo_rx = + (volatile mac_fifo_t*)(MAC0_RX_DMA_ADDR+MAC_RX_BUFF0_STATUS); + int i; + + next_tx = TX_GET_DMA_BUFFER(fifo_tx[0].addr); + next_rx = RX_GET_DMA_BUFFER(fifo_rx[0].addr); + + /* We have to enable clocks before releasing reset */ + *macen = MAC_EN_CLOCK_ENABLE; + udelay(10); + + /* Enable MAC0 */ + /* We have to release reset before accessing registers */ + *macen = MAC_EN_CLOCK_ENABLE|MAC_EN_RESET0| + MAC_EN_RESET1|MAC_EN_RESET2; + udelay(10); + + for(i=0;i<NO_OF_FIFOS;i++){ + fifo_tx[i].len = 0; + fifo_tx[i].addr = virt_to_phys(&txbuf[0]); + fifo_rx[i].addr = (virt_to_phys(NetRxPackets[i]))|RX_DMA_ENABLE; + } + + /* Put mac addr in little endian */ +#define ea eth_get_dev()->enetaddr + *mac_addr_high = (ea[5] << 8) | (ea[4] ) ; + *mac_addr_low = (ea[3] << 24) | (ea[2] << 16) | + (ea[1] << 8) | (ea[0] ) ; +#undef ea + *mac_mcast_low = 0; + *mac_mcast_high = 0; + + /* Make sure the MAC buffer is in the correct endian mode */ +#ifdef __LITTLE_ENDIAN + *mac_ctrl = MAC_FULL_DUPLEX; + udelay(1); + *mac_ctrl = MAC_FULL_DUPLEX|MAC_RX_ENABLE|MAC_TX_ENABLE; +#else + *mac_ctrl = MAC_BIG_ENDIAN|MAC_FULL_DUPLEX; + udelay(1); + *mac_ctrl = MAC_BIG_ENDIAN|MAC_FULL_DUPLEX|MAC_RX_ENABLE|MAC_TX_ENABLE; +#endif + + return(1); +} + +static void au1x00_halt(struct eth_device* dev){ + volatile u32 *macen = (volatile u32*)MAC0_ENABLE; + + /* Put MAC0 in reset */ + *macen = 0; +} + +int au1x00_enet_initialize(bd_t *bis){ + struct eth_device* dev; + + if ((dev = (struct eth_device*)malloc(sizeof *dev)) == NULL) { + puts ("malloc failed\n"); + return -1; + } + + memset(dev, 0, sizeof *dev); + + sprintf(dev->name, "Au1X00 ethernet"); + dev->iobase = 0; + dev->priv = 0; + dev->init = au1x00_init; + dev->halt = au1x00_halt; + dev->send = au1x00_send; + dev->recv = au1x00_recv; + + eth_register(dev); + +#if defined(CONFIG_CMD_MII) + miiphy_register(dev->name, + au1x00_miiphy_read, au1x00_miiphy_write); +#endif + + return 1; +} |