diff options
Diffstat (limited to 'u-boot/board/davinci/da8xxevm/da850evm.c')
| -rw-r--r-- | u-boot/board/davinci/da8xxevm/da850evm.c | 336 |
1 files changed, 336 insertions, 0 deletions
diff --git a/u-boot/board/davinci/da8xxevm/da850evm.c b/u-boot/board/davinci/da8xxevm/da850evm.c new file mode 100644 index 0000000..b088c9c --- /dev/null +++ b/u-boot/board/davinci/da8xxevm/da850evm.c @@ -0,0 +1,336 @@ +/* + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * + * Based on da830evm.c. Original Copyrights follow: + * + * Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. <nick.thompson@gefanuc.com> + * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <common.h> +#include <i2c.h> +#include <net.h> +#include <netdev.h> +#include <asm/arch/hardware.h> +#include <asm/arch/emif_defs.h> +#include <asm/arch/emac_defs.h> +#include <asm/io.h> +#include <asm/arch/davinci_misc.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define pinmux(x) (&davinci_syscfg_regs->pinmux[x]) + +/* SPI0 pin muxer settings */ +static const struct pinmux_config spi1_pins[] = { + { pinmux(5), 1, 1 }, + { pinmux(5), 1, 2 }, + { pinmux(5), 1, 4 }, + { pinmux(5), 1, 5 } +}; + +/* UART pin muxer settings */ +static const struct pinmux_config uart_pins[] = { + { pinmux(0), 4, 6 }, + { pinmux(0), 4, 7 }, + { pinmux(4), 2, 4 }, + { pinmux(4), 2, 5 } +}; + +#ifdef CONFIG_DRIVER_TI_EMAC +static const struct pinmux_config emac_pins[] = { +#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII + { pinmux(14), 8, 2 }, + { pinmux(14), 8, 3 }, + { pinmux(14), 8, 4 }, + { pinmux(14), 8, 5 }, + { pinmux(14), 8, 6 }, + { pinmux(14), 8, 7 }, + { pinmux(15), 8, 1 }, +#else /* ! CONFIG_DRIVER_TI_EMAC_USE_RMII */ + { pinmux(2), 8, 1 }, + { pinmux(2), 8, 2 }, + { pinmux(2), 8, 3 }, + { pinmux(2), 8, 4 }, + { pinmux(2), 8, 5 }, + { pinmux(2), 8, 6 }, + { pinmux(2), 8, 7 }, + { pinmux(3), 8, 0 }, + { pinmux(3), 8, 1 }, + { pinmux(3), 8, 2 }, + { pinmux(3), 8, 3 }, + { pinmux(3), 8, 4 }, + { pinmux(3), 8, 5 }, + { pinmux(3), 8, 6 }, + { pinmux(3), 8, 7 }, +#endif /* CONFIG_DRIVER_TI_EMAC_USE_RMII */ + { pinmux(4), 8, 0 }, + { pinmux(4), 8, 1 } +}; + +/* I2C pin muxer settings */ +static const struct pinmux_config i2c_pins[] = { + { pinmux(4), 2, 2 }, + { pinmux(4), 2, 3 } +}; + +#ifdef CONFIG_NAND_DAVINCI +const struct pinmux_config nand_pins[] = { + { pinmux(7), 1, 1 }, + { pinmux(7), 1, 2 }, + { pinmux(7), 1, 4 }, + { pinmux(7), 1, 5 }, + { pinmux(9), 1, 0 }, + { pinmux(9), 1, 1 }, + { pinmux(9), 1, 2 }, + { pinmux(9), 1, 3 }, + { pinmux(9), 1, 4 }, + { pinmux(9), 1, 5 }, + { pinmux(9), 1, 6 }, + { pinmux(9), 1, 7 }, + { pinmux(12), 1, 5 }, + { pinmux(12), 1, 6 } +}; +#endif + +#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII +#define HAS_RMII 1 +#else +#define HAS_RMII 0 +#endif +#endif /* CONFIG_DRIVER_TI_EMAC */ + +static const struct pinmux_resource pinmuxes[] = { +#ifdef CONFIG_SPI_FLASH + PINMUX_ITEM(spi1_pins), +#endif + PINMUX_ITEM(uart_pins), + PINMUX_ITEM(i2c_pins), +#ifdef CONFIG_NAND_DAVINCI + PINMUX_ITEM(nand_pins), +#endif +}; + +static const struct lpsc_resource lpsc[] = { + { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */ + { DAVINCI_LPSC_SPI1 }, /* Serial Flash */ + { DAVINCI_LPSC_EMAC }, /* image download */ + { DAVINCI_LPSC_UART2 }, /* console */ + { DAVINCI_LPSC_GPIO }, +}; + +#ifndef CONFIG_DA850_EVM_MAX_CPU_CLK +#define CONFIG_DA850_EVM_MAX_CPU_CLK 300000000 +#endif + +/* + * get_board_rev() - setup to pass kernel board revision information + * Returns: + * bit[0-3] Maximum cpu clock rate supported by onboard SoC + * 0000b - 300 MHz + * 0001b - 372 MHz + * 0010b - 408 MHz + * 0011b - 456 MHz + */ +u32 get_board_rev(void) +{ + char *s; + u32 maxcpuclk = CONFIG_DA850_EVM_MAX_CPU_CLK; + u32 rev = 0; + + s = getenv("maxcpuclk"); + if (s) + maxcpuclk = simple_strtoul(s, NULL, 10); + + if (maxcpuclk >= 456000000) + rev = 3; + else if (maxcpuclk >= 408000000) + rev = 2; + else if (maxcpuclk >= 372000000) + rev = 1; + + return rev; +} + +int board_init(void) +{ +#ifndef CONFIG_USE_IRQ + irq_init(); +#endif + + +#ifdef CONFIG_NAND_DAVINCI + /* + * NAND CS setup - cycle counts based on da850evm NAND timings in the + * Linux kernel @ 25MHz EMIFA + */ + writel((DAVINCI_ABCR_WSETUP(0) | + DAVINCI_ABCR_WSTROBE(0) | + DAVINCI_ABCR_WHOLD(0) | + DAVINCI_ABCR_RSETUP(0) | + DAVINCI_ABCR_RSTROBE(1) | + DAVINCI_ABCR_RHOLD(0) | + DAVINCI_ABCR_TA(0) | + DAVINCI_ABCR_ASIZE_8BIT), + &davinci_emif_regs->ab2cr); /* CS3 */ +#endif + + /* arch number of the board */ + gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DA850_EVM; + + /* address of boot parameters */ + gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR; + + /* + * Power on required peripherals + * ARM does not have access by default to PSC0 and PSC1 + * assuming here that the DSP bootloader has set the IOPU + * such that PSC access is available to ARM + */ + if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc))) + return 1; + + /* setup the SUSPSRC for ARM to control emulation suspend */ + writel(readl(&davinci_syscfg_regs->suspsrc) & + ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C | + DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 | + DAVINCI_SYSCFG_SUSPSRC_UART2), + &davinci_syscfg_regs->suspsrc); + + /* configure pinmux settings */ + if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes))) + return 1; + +#ifdef CONFIG_DRIVER_TI_EMAC + if (davinci_configure_pin_mux(emac_pins, ARRAY_SIZE(emac_pins)) != 0) + return 1; + + davinci_emac_mii_mode_sel(HAS_RMII); +#endif /* CONFIG_DRIVER_TI_EMAC */ + + /* enable the console UART */ + writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST | + DAVINCI_UART_PWREMU_MGMT_UTRST), + &davinci_uart2_ctrl_regs->pwremu_mgmt); + + return 0; +} + +#ifdef CONFIG_DRIVER_TI_EMAC + +#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII +/** + * rmii_hw_init + * + * DA850/OMAP-L138 EVM can interface to a daughter card for + * additional features. This card has an I2C GPIO Expander TCA6416 + * to select the required functions like camera, RMII Ethernet, + * character LCD, video. + * + * Initialization of the expander involves configuring the + * polarity and direction of the ports. P07-P05 are used here. + * These ports are connected to a Mux chip which enables only one + * functionality at a time. + * + * For RMII phy to respond, the MII MDIO clock has to be disabled + * since both the PHY devices have address as zero. The MII MDIO + * clock is controlled via GPIO2[6]. + * + * This code is valid for Beta version of the hardware + */ +int rmii_hw_init(void) +{ + const struct pinmux_config gpio_pins[] = { + { pinmux(6), 8, 1 } + }; + u_int8_t buf[2]; + unsigned int temp; + int ret; + + /* PinMux for GPIO */ + if (davinci_configure_pin_mux(gpio_pins, ARRAY_SIZE(gpio_pins)) != 0) + return 1; + + /* I2C Exapnder configuration */ + /* Set polarity to non-inverted */ + buf[0] = 0x0; + buf[1] = 0x0; + ret = i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 4, 1, buf, 2); + if (ret) { + printf("\nExpander @ 0x%02x write FAILED!!!\n", + CONFIG_SYS_I2C_EXPANDER_ADDR); + return ret; + } + + /* Configure P07-P05 as outputs */ + buf[0] = 0x1f; + buf[1] = 0xff; + ret = i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 6, 1, buf, 2); + if (ret) { + printf("\nExpander @ 0x%02x write FAILED!!!\n", + CONFIG_SYS_I2C_EXPANDER_ADDR); + } + + /* For Ethernet RMII selection + * P07(SelA)=0 + * P06(SelB)=1 + * P05(SelC)=1 + */ + if (i2c_read(CONFIG_SYS_I2C_EXPANDER_ADDR, 2, 1, buf, 1)) { + printf("\nExpander @ 0x%02x read FAILED!!!\n", + CONFIG_SYS_I2C_EXPANDER_ADDR); + } + + buf[0] &= 0x1f; + buf[0] |= (0 << 7) | (1 << 6) | (1 << 5); + if (i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 2, 1, buf, 1)) { + printf("\nExpander @ 0x%02x write FAILED!!!\n", + CONFIG_SYS_I2C_EXPANDER_ADDR); + } + + /* Set the output as high */ + temp = REG(GPIO_BANK2_REG_SET_ADDR); + temp |= (0x01 << 6); + REG(GPIO_BANK2_REG_SET_ADDR) = temp; + + /* Set the GPIO direction as output */ + temp = REG(GPIO_BANK2_REG_DIR_ADDR); + temp &= ~(0x01 << 6); + REG(GPIO_BANK2_REG_DIR_ADDR) = temp; + + return 0; +} +#endif /* CONFIG_DRIVER_TI_EMAC_USE_RMII */ + +/* + * Initializes on-board ethernet controllers. + */ +int board_eth_init(bd_t *bis) +{ +#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII + /* Select RMII fucntion through the expander */ + if (rmii_hw_init()) + printf("RMII hardware init failed!!!\n"); +#endif + if (!davinci_emac_initialize()) { + printf("Error: Ethernet init failed!\n"); + return -1; + } + + return 0; +} +#endif /* CONFIG_DRIVER_TI_EMAC */ |