diff options
Diffstat (limited to 'u-boot/board/esd/pmc440/pmc440.c')
| -rw-r--r-- | u-boot/board/esd/pmc440/pmc440.c | 904 |
1 files changed, 904 insertions, 0 deletions
diff --git a/u-boot/board/esd/pmc440/pmc440.c b/u-boot/board/esd/pmc440/pmc440.c new file mode 100644 index 0000000..5236f44 --- /dev/null +++ b/u-boot/board/esd/pmc440/pmc440.c @@ -0,0 +1,904 @@ +/* + * (Cg) Copyright 2007-2008 + * Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com. + * Based on board/amcc/sequoia/sequoia.c + * + * (C) Copyright 2006 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * (C) Copyright 2006 + * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com + * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <asm/ppc440.h> +#include <asm/processor.h> +#include <asm/io.h> +#include <asm/bitops.h> +#include <command.h> +#include <i2c.h> +#ifdef CONFIG_RESET_PHY_R +#include <miiphy.h> +#endif +#include <serial.h> +#include <asm/4xx_pci.h> + +#include "fpga.h" +#include "pmc440.h" + +DECLARE_GLOBAL_DATA_PTR; + +extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */ +extern void __ft_board_setup(void *blob, bd_t *bd); + +ulong flash_get_size(ulong base, int banknum); +int pci_is_66mhz(void); +int is_monarch(void); +int bootstrap_eeprom_read(unsigned dev_addr, unsigned offset, + uchar *buffer, unsigned cnt); + +struct serial_device *default_serial_console(void) +{ + uchar buf[4]; + ulong delay; + int i; + ulong val; + + /* + * Use default console on P4 when strapping jumper + * is installed (bootstrap option != 'H'). + */ + mfsdr(SDR0_PINSTP, val); + if (((val & 0xf0000000) >> 29) != 7) + return &eserial2_device; + + ulong scratchreg = in_be32((void*)GPIO0_ISR3L); + if (!(scratchreg & 0x80)) { + /* mark scratchreg valid */ + scratchreg = (scratchreg & 0xffffff00) | 0x80; + + i = bootstrap_eeprom_read(CONFIG_SYS_I2C_BOOT_EEPROM_ADDR, + 0x10, buf, 4); + if ((i != -1) && (buf[0] == 0x19) && (buf[1] == 0x75)) { + scratchreg |= buf[2]; + + /* bringup delay for console */ + for (delay=0; delay<(1000 * (ulong)buf[3]); delay++) { + udelay(1000); + } + } else + scratchreg |= 0x01; + out_be32((void*)GPIO0_ISR3L, scratchreg); + } + + if (scratchreg & 0x01) + return &eserial2_device; + else + return &eserial1_device; +} + +int board_early_init_f(void) +{ + u32 sdr0_cust0; + u32 sdr0_pfc1, sdr0_pfc2; + u32 reg; + + /* general EBC configuration (disable EBC timeouts) */ + mtdcr(EBC0_CFGADDR, EBC0_CFG); + mtdcr(EBC0_CFGDATA, 0xf8400000); + + /* + * Setup the GPIO pins + * TODO: setup GPIOs via CONFIG_SYS_4xx_GPIO_TABLE in board's config file + */ + out_be32((void *)GPIO0_OR, 0x40000102); + out_be32((void *)GPIO0_TCR, 0x4c90011f); + out_be32((void *)GPIO0_OSRL, 0x28051400); + out_be32((void *)GPIO0_OSRH, 0x55005000); + out_be32((void *)GPIO0_TSRL, 0x08051400); + out_be32((void *)GPIO0_TSRH, 0x55005000); + out_be32((void *)GPIO0_ISR1L, 0x54000000); + out_be32((void *)GPIO0_ISR1H, 0x00000000); + out_be32((void *)GPIO0_ISR2L, 0x44000000); + out_be32((void *)GPIO0_ISR2H, 0x00000100); + out_be32((void *)GPIO0_ISR3L, 0x00000000); + out_be32((void *)GPIO0_ISR3H, 0x00000000); + + out_be32((void *)GPIO1_OR, 0x80002408); + out_be32((void *)GPIO1_TCR, 0xd6003c08); + out_be32((void *)GPIO1_OSRL, 0x0a5a0000); + out_be32((void *)GPIO1_OSRH, 0x00000000); + out_be32((void *)GPIO1_TSRL, 0x00000000); + out_be32((void *)GPIO1_TSRH, 0x00000000); + out_be32((void *)GPIO1_ISR1L, 0x00005555); + out_be32((void *)GPIO1_ISR1H, 0x40000000); + out_be32((void *)GPIO1_ISR2L, 0x04010000); + out_be32((void *)GPIO1_ISR2H, 0x00000000); + out_be32((void *)GPIO1_ISR3L, 0x01400000); + out_be32((void *)GPIO1_ISR3H, 0x00000000); + + /* patch PLB:PCI divider for 66MHz PCI */ + mfcpr(CPR0_SPCID, reg); + if (pci_is_66mhz() && (reg != 0x02000000)) { + mtcpr(CPR0_SPCID, 0x02000000); /* 133MHZ : 2 for 66MHz PCI */ + + mfcpr(CPR0_ICFG, reg); + reg |= CPR0_ICFG_RLI_MASK; + mtcpr(CPR0_ICFG, reg); + + mtspr(SPRN_DBCR0, 0x20000000); /* do chip reset */ + } + + /* + * Setup the interrupt controller polarities, triggers, etc. + */ + mtdcr(UIC0SR, 0xffffffff); /* clear all */ + mtdcr(UIC0ER, 0x00000000); /* disable all */ + mtdcr(UIC0CR, 0x00000005); /* ATI & UIC1 crit are critical */ + mtdcr(UIC0PR, 0xfffff7ef); + mtdcr(UIC0TR, 0x00000000); + mtdcr(UIC0VR, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(UIC0SR, 0xffffffff); /* clear all */ + + mtdcr(UIC1SR, 0xffffffff); /* clear all */ + mtdcr(UIC1ER, 0x00000000); /* disable all */ + mtdcr(UIC1CR, 0x00000000); /* all non-critical */ + mtdcr(UIC1PR, 0xffffc7f5); + mtdcr(UIC1TR, 0x00000000); + mtdcr(UIC1VR, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(UIC1SR, 0xffffffff); /* clear all */ + + mtdcr(UIC2SR, 0xffffffff); /* clear all */ + mtdcr(UIC2ER, 0x00000000); /* disable all */ + mtdcr(UIC2CR, 0x00000000); /* all non-critical */ + mtdcr(UIC2PR, 0x27ffffff); + mtdcr(UIC2TR, 0x00000000); + mtdcr(UIC2VR, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(UIC2SR, 0xffffffff); /* clear all */ + + /* select Ethernet pins */ + mfsdr(SDR0_PFC1, sdr0_pfc1); + sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SELECT_MASK) | + SDR0_PFC1_SELECT_CONFIG_4; + mfsdr(SDR0_PFC2, sdr0_pfc2); + sdr0_pfc2 = (sdr0_pfc2 & ~SDR0_PFC2_SELECT_MASK) | + SDR0_PFC2_SELECT_CONFIG_4; + + /* enable 2nd IIC */ + sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SIS_MASK) | SDR0_PFC1_SIS_IIC1_SEL; + + mtsdr(SDR0_PFC2, sdr0_pfc2); + mtsdr(SDR0_PFC1, sdr0_pfc1); + + /* setup NAND FLASH */ + mfsdr(SDR0_CUST0, sdr0_cust0); + sdr0_cust0 = SDR0_CUST0_MUX_NDFC_SEL | + SDR0_CUST0_NDFC_ENABLE | + SDR0_CUST0_NDFC_BW_8_BIT | + SDR0_CUST0_NDFC_ARE_MASK | + (0x80000000 >> (28 + CONFIG_SYS_NAND_CS)); + mtsdr(SDR0_CUST0, sdr0_cust0); + + return 0; +} + +#if defined(CONFIG_MISC_INIT_F) +int misc_init_f(void) +{ + struct pci_controller hose; + hose.first_busno = 0; + hose.last_busno = 0; + hose.region_count = 0; + + if (getenv("pciearly") && (!is_monarch())) { + printf("PCI: early target init\n"); + pci_setup_indirect(&hose, PCIL0_CFGADR, PCIL0_CFGDATA); + pci_target_init(&hose); + } + return 0; +} +#endif + +/* + * misc_init_r. + */ +int misc_init_r(void) +{ + uint pbcr; + int size_val = 0; + u32 reg; + unsigned long usb2d0cr = 0; + unsigned long usb2phy0cr, usb2h0cr = 0; + unsigned long sdr0_pfc1; + unsigned long sdr0_srst0, sdr0_srst1; + char *act = getenv("usbact"); + + /* + * FLASH stuff... + */ + + /* Re-do sizing to get full correct info */ + + /* adjust flash start and offset */ + gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize; + gd->bd->bi_flashoffset = 0; + +#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) + mtdcr(EBC0_CFGADDR, PB2CR); +#else + mtdcr(EBC0_CFGADDR, PB0CR); +#endif + pbcr = mfdcr(EBC0_CFGDATA); + size_val = ffs(gd->bd->bi_flashsize) - 21; + pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17); +#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) + mtdcr(EBC0_CFGADDR, PB2CR); +#else + mtdcr(EBC0_CFGADDR, PB0CR); +#endif + mtdcr(EBC0_CFGDATA, pbcr); + + /* + * Re-check to get correct base address + */ + flash_get_size(gd->bd->bi_flashstart, 0); + +#ifdef CONFIG_ENV_IS_IN_FLASH + /* Monitor protection ON by default */ + (void)flash_protect(FLAG_PROTECT_SET, + -CONFIG_SYS_MONITOR_LEN, + 0xffffffff, + &flash_info[0]); + + /* Env protection ON by default */ + (void)flash_protect(FLAG_PROTECT_SET, + CONFIG_ENV_ADDR_REDUND, + CONFIG_ENV_ADDR_REDUND + 2*CONFIG_ENV_SECT_SIZE - 1, + &flash_info[0]); +#endif + + /* + * USB suff... + */ + if ((act == NULL || strcmp(act, "host") == 0) && + !(in_be32((void*)GPIO0_IR) & GPIO0_USB_PRSNT)){ + /* SDR Setting */ + mfsdr(SDR0_PFC1, sdr0_pfc1); + mfsdr(SDR0_USB2D0CR, usb2d0cr); + mfsdr(SDR0_USB2PHY0CR, usb2phy0cr); + mfsdr(SDR0_USB2H0CR, usb2h0cr); + + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ; + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS; + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; + + /* + * An 8-bit/60MHz interface is the only possible alternative + * when connecting the Device to the PHY + */ + usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK; + usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ; + + usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK; + sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK; + + mtsdr(SDR0_PFC1, sdr0_pfc1); + mtsdr(SDR0_USB2D0CR, usb2d0cr); + mtsdr(SDR0_USB2PHY0CR, usb2phy0cr); + mtsdr(SDR0_USB2H0CR, usb2h0cr); + + /* + * Take USB out of reset: + * -Initial status = all cores are in reset + * -deassert reset to OPB1, P4OPB0, OPB2, PLB42OPB1 OPB2PLB40 cores + * -wait 1 ms + * -deassert reset to PHY + * -wait 1 ms + * -deassert reset to HOST + * -wait 4 ms + * -deassert all other resets + */ + mfsdr(SDR0_SRST1, sdr0_srst1); + sdr0_srst1 &= ~(SDR0_SRST1_OPBA1 | \ + SDR0_SRST1_P4OPB0 | \ + SDR0_SRST1_OPBA2 | \ + SDR0_SRST1_PLB42OPB1 | \ + SDR0_SRST1_OPB2PLB40); + mtsdr(SDR0_SRST1, sdr0_srst1); + udelay(1000); + + mfsdr(SDR0_SRST1, sdr0_srst1); + sdr0_srst1 &= ~SDR0_SRST1_USB20PHY; + mtsdr(SDR0_SRST1, sdr0_srst1); + udelay(1000); + + mfsdr(SDR0_SRST0, sdr0_srst0); + sdr0_srst0 &= ~SDR0_SRST0_USB2H; + mtsdr(SDR0_SRST0, sdr0_srst0); + udelay(4000); + + /* finally all the other resets */ + mtsdr(SDR0_SRST1, 0x00000000); + mtsdr(SDR0_SRST0, 0x00000000); + + if (!(in_be32((void*)GPIO0_IR) & GPIO0_USB_PRSNT)) { + /* enable power on USB socket */ + out_be32((void*)GPIO1_OR, + in_be32((void*)GPIO1_OR) & ~GPIO1_USB_PWR_N); + } + + printf("USB: Host\n"); + + } else if ((strcmp(act, "dev") == 0) || + (in_be32((void*)GPIO0_IR) & GPIO0_USB_PRSNT)) { + mfsdr(SDR0_USB2PHY0CR, usb2phy0cr); + + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS; + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; + mtsdr(SDR0_USB2PHY0CR, usb2phy0cr); + + udelay (1000); + mtsdr(SDR0_SRST1, 0x672c6000); + + udelay (1000); + mtsdr(SDR0_SRST0, 0x00000080); + + udelay (1000); + mtsdr(SDR0_SRST1, 0x60206000); + + *(unsigned int *)(0xe0000350) = 0x00000001; + + udelay (1000); + mtsdr(SDR0_SRST1, 0x60306000); + + /* SDR Setting */ + mfsdr(SDR0_USB2PHY0CR, usb2phy0cr); + mfsdr(SDR0_USB2H0CR, usb2h0cr); + mfsdr(SDR0_USB2D0CR, usb2d0cr); + mfsdr(SDR0_PFC1, sdr0_pfc1); + + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ; + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PUREN; + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_DEV; + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_DEV; + + usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK; + usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_8BIT_60MHZ; + + usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK; + + sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK; + sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_EBCHR_SEL; + + mtsdr(SDR0_USB2H0CR, usb2h0cr); + mtsdr(SDR0_USB2PHY0CR, usb2phy0cr); + mtsdr(SDR0_USB2D0CR, usb2d0cr); + mtsdr(SDR0_PFC1, sdr0_pfc1); + + /*clear resets*/ + udelay(1000); + mtsdr(SDR0_SRST1, 0x00000000); + udelay(1000); + mtsdr(SDR0_SRST0, 0x00000000); + + printf("USB: Device\n"); + } + + /* + * Clear PLB4A0_ACR[WRP] + * This fix will make the MAL burst disabling patch for the Linux + * EMAC driver obsolete. + */ + reg = mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_WRP_MASK; + mtdcr(PLB4A0_ACR, reg); + +#ifdef CONFIG_FPGA + pmc440_init_fpga(); +#endif + + /* turn off POST LED */ + out_be32((void*)GPIO1_OR, in_be32((void*)GPIO1_OR) & ~GPIO1_POST_N); + /* turn on RUN LED */ + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) & ~GPIO0_LED_RUN_N); + return 0; +} + +int is_monarch(void) +{ + if (in_be32((void*)GPIO1_IR) & GPIO1_NONMONARCH) + return 0; + + return 1; +} + +int pci_is_66mhz(void) +{ + if (in_be32((void*)GPIO1_IR) & GPIO1_M66EN) + return 1; + return 0; +} + +int board_revision(void) +{ + return (int)((in_be32((void*)GPIO1_IR) & GPIO1_HWID_MASK) >> 4); +} + +int checkboard(void) +{ + puts("Board: esd GmbH - PMC440"); + + gd->board_type = board_revision(); + printf(", Rev 1.%ld, ", gd->board_type); + + if (!is_monarch()) { + puts("non-"); + } + + printf("monarch, PCI=%s MHz\n", pci_is_66mhz() ? "66" : "33"); + return (0); +} + + +#if defined(CONFIG_PCI) && defined(CONFIG_PCI_PNP) +/* + * Assign interrupts to PCI devices. Some OSs rely on this. + */ +void board_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev) +{ + unsigned char int_line[] = {IRQ_PCIC, IRQ_PCID, IRQ_PCIA, IRQ_PCIB}; + + pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, + int_line[PCI_DEV(dev) & 0x03]); +} +#endif + +/* + * pci_target_init + * + * The bootstrap configuration provides default settings for the pci + * inbound map (PIM). But the bootstrap config choices are limited and + * may not be sufficient for a given board. + */ +#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) +void pci_target_init(struct pci_controller *hose) +{ + char *ptmla_str, *ptmms_str; + + /* + * Set up Direct MMIO registers + */ + /* + * PowerPC440EPX PCI Master configuration. + * Map one 1Gig range of PLB/processor addresses to PCI memory space. + * PLB address 0x80000000-0xBFFFFFFF + * ==> PCI address 0x80000000-0xBFFFFFFF + * Use byte reversed out routines to handle endianess. + * Make this region non-prefetchable. + */ + out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */ + /* - disabled b4 setting */ + out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */ + out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */ + out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */ + out32r(PCIL0_PMM0MA, 0xc0000001); /* 1G + No prefetching, */ + /* and enable region */ + + if (!is_monarch()) { + ptmla_str = getenv("ptm1la"); + ptmms_str = getenv("ptm1ms"); + if(NULL != ptmla_str && NULL != ptmms_str ) { + out32r(PCIL0_PTM1MS, + simple_strtoul(ptmms_str, NULL, 16)); + out32r(PCIL0_PTM1LA, + simple_strtoul(ptmla_str, NULL, 16)); + } else { + /* BAR1: default top 64MB of RAM */ + out32r(PCIL0_PTM1MS, 0xfc000001); + out32r(PCIL0_PTM1LA, 0x0c000000); + } + } else { + /* BAR1: default: complete 256MB RAM */ + out32r(PCIL0_PTM1MS, 0xf0000001); + out32r(PCIL0_PTM1LA, 0x00000000); + } + + ptmla_str = getenv("ptm2la"); /* Local Addr. Reg */ + ptmms_str = getenv("ptm2ms"); /* Memory Size/Attribute */ + if(NULL != ptmla_str && NULL != ptmms_str ) { + out32r(PCIL0_PTM2MS, simple_strtoul(ptmms_str, NULL, 16)); + out32r(PCIL0_PTM2LA, simple_strtoul(ptmla_str, NULL, 16)); + } else { + /* BAR2: default: 4MB FPGA */ + out32r(PCIL0_PTM2MS, 0xffc00001); /* Memory Size/Attribute */ + out32r(PCIL0_PTM2LA, 0xef000000); /* Local Addr. Reg */ + } + + if (is_monarch()) { + /* BAR2: map FPGA registers behind system memory at 1GB */ + pci_hose_write_config_dword(hose, 0, PCI_BASE_ADDRESS_2, 0x40000008); + } + + /* + * Set up Configuration registers + */ + + /* Program the board's vendor id */ + pci_hose_write_config_word(hose, 0, PCI_SUBSYSTEM_VENDOR_ID, + CONFIG_SYS_PCI_SUBSYS_VENDORID); + + /* disabled for PMC405 backward compatibility */ + /* Configure command register as bus master */ + /* pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER); */ + + + /* 240nS PCI clock */ + pci_hose_write_config_word(hose, 0, PCI_LATENCY_TIMER, 1); + + /* No error reporting */ + pci_hose_write_config_word(hose, 0, PCI_ERREN, 0); + + pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101); + + if (!is_monarch()) { + /* Program the board's subsystem id/classcode */ + pci_hose_write_config_word(hose, 0, PCI_SUBSYSTEM_ID, + CONFIG_SYS_PCI_SUBSYS_ID_NONMONARCH); + pci_hose_write_config_word(hose, 0, PCI_CLASS_SUB_CODE, + CONFIG_SYS_PCI_CLASSCODE_NONMONARCH); + + /* PCI configuration done: release ERREADY */ + out_be32((void*)GPIO1_OR, + in_be32((void*)GPIO1_OR) | GPIO1_PPC_EREADY); + out_be32((void*)GPIO1_TCR, + in_be32((void*)GPIO1_TCR) | GPIO1_PPC_EREADY); + } else { + /* Program the board's subsystem id/classcode */ + pci_hose_write_config_word(hose, 0, PCI_SUBSYSTEM_ID, + CONFIG_SYS_PCI_SUBSYS_ID_MONARCH); + pci_hose_write_config_word(hose, 0, PCI_CLASS_SUB_CODE, + CONFIG_SYS_PCI_CLASSCODE_MONARCH); + } + + /* enable host configuration */ + pci_hose_write_config_dword(hose, 0, PCI_BRDGOPT2, 0x00000101); +} +#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ + +/* + * Override weak default pci_master_init() + */ +#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) +void pci_master_init(struct pci_controller *hose) +{ + /* + * Only configure the master in monach mode + */ + if (is_monarch()) + __pci_master_init(hose); +} +#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */ + +static void wait_for_pci_ready(void) +{ + int i; + char *s = getenv("pcidelay"); + /* + * We have our own handling of the pcidelay variable. + * Using CONFIG_PCI_BOOTDELAY enables pausing for host + * and adapter devices. For adapter devices we do not + * want this. + */ + if (s) { + int ms = simple_strtoul(s, NULL, 10); + printf("PCI: Waiting for %d ms\n", ms); + for (i=0; i<ms; i++) + udelay(1000); + } + + if (!(in_be32((void*)GPIO1_IR) & GPIO1_PPC_EREADY)) { + printf("PCI: Waiting for EREADY (CTRL-C to skip) ... "); + while (1) { + if (ctrlc()) { + puts("abort\n"); + break; + } + if (in_be32((void*)GPIO1_IR) & GPIO1_PPC_EREADY) { + printf("done\n"); + break; + } + } + } +} + +/* + * Override weak is_pci_host() + * + * This routine is called to determine if a pci scan should be + * performed. With various hardware environments (especially cPCI and + * PPMC) it's insufficient to depend on the state of the arbiter enable + * bit in the strap register, or generic host/adapter assumptions. + * + * Rather than hard-code a bad assumption in the general 440 code, the + * 440 pci code requires the board to decide at runtime. + * + * Return 0 for adapter mode, non-zero for host (monarch) mode. + */ +#if defined(CONFIG_PCI) +int is_pci_host(struct pci_controller *hose) +{ + char *s = getenv("pciscan"); + if (s == NULL) + if (is_monarch()) { + wait_for_pci_ready(); + return 1; + } else + return 0; + else if (!strcmp(s, "yes")) + return 1; + + return 0; +} +#endif /* defined(CONFIG_PCI) */ + +#ifdef CONFIG_RESET_PHY_R +void reset_phy(void) +{ + char *s; + unsigned short val_method, val_behavior; + + /* special LED setup for NGCC/CANDES */ + if ((s = getenv("bd_type")) && + ((!strcmp(s, "ngcc")) || (!strcmp(s, "candes")))) { + val_method = 0x0e0a; + val_behavior = 0x0cf2; + } else { + /* PMC440 standard type */ + val_method = 0x0e10; + val_behavior = 0x0cf0; + } + + if (miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, 0x1f, 0x0001) == 0) { + miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, 0x11, 0x0010); + miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, 0x11, val_behavior); + miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, 0x10, val_method); + miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, 0x1f, 0x0000); + } + + if (miiphy_write("ppc_4xx_eth1", CONFIG_PHY1_ADDR, 0x1f, 0x0001) == 0) { + miiphy_write("ppc_4xx_eth1", CONFIG_PHY1_ADDR, 0x11, 0x0010); + miiphy_write("ppc_4xx_eth1", CONFIG_PHY1_ADDR, 0x11, val_behavior); + miiphy_write("ppc_4xx_eth1", CONFIG_PHY1_ADDR, 0x10, val_method); + miiphy_write("ppc_4xx_eth1", CONFIG_PHY1_ADDR, 0x1f, 0x0000); + } +} +#endif + +#if defined(CONFIG_SYS_EEPROM_WREN) +/* + * Input: <dev_addr> I2C address of EEPROM device to enable. + * <state> -1: deliver current state + * 0: disable write + * 1: enable write + * Returns: -1: wrong device address + * 0: dis-/en- able done + * 0/1: current state if <state> was -1. + */ +int eeprom_write_enable(unsigned dev_addr, int state) +{ + if ((CONFIG_SYS_I2C_EEPROM_ADDR != dev_addr) && + (CONFIG_SYS_I2C_BOOT_EEPROM_ADDR != dev_addr)) { + return -1; + } else { + switch (state) { + case 1: + /* Enable write access, clear bit GPIO_SINT2. */ + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) & ~GPIO0_EP_EEP); + state = 0; + break; + case 0: + /* Disable write access, set bit GPIO_SINT2. */ + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) | GPIO0_EP_EEP); + state = 0; + break; + default: + /* Read current status back. */ + state = (0 == (in_be32((void *)GPIO0_OR) + & GPIO0_EP_EEP)); + break; + } + } + return state; +} +#endif /* #if defined(CONFIG_SYS_EEPROM_WREN) */ + +#define CONFIG_SYS_BOOT_EEPROM_PAGE_WRITE_BITS 3 +int bootstrap_eeprom_write(unsigned dev_addr, unsigned offset, + uchar *buffer, unsigned cnt) +{ + unsigned end = offset + cnt; + unsigned blk_off; + int rcode = 0; + +#if defined(CONFIG_SYS_EEPROM_WREN) + eeprom_write_enable(dev_addr, 1); +#endif + /* + * Write data until done or would cross a write page boundary. + * We must write the address again when changing pages + * because the address counter only increments within a page. + */ + + while (offset < end) { + unsigned alen, len; + unsigned maxlen; + uchar addr[2]; + + blk_off = offset & 0xFF; /* block offset */ + + addr[0] = offset >> 8; /* block number */ + addr[1] = blk_off; /* block offset */ + alen = 2; + addr[0] |= dev_addr; /* insert device address */ + + len = end - offset; + +#define BOOT_EEPROM_PAGE_SIZE (1 << CONFIG_SYS_BOOT_EEPROM_PAGE_WRITE_BITS) +#define BOOT_EEPROM_PAGE_OFFSET(x) ((x) & (BOOT_EEPROM_PAGE_SIZE - 1)) + + maxlen = BOOT_EEPROM_PAGE_SIZE - + BOOT_EEPROM_PAGE_OFFSET(blk_off); + if (maxlen > I2C_RXTX_LEN) + maxlen = I2C_RXTX_LEN; + + if (len > maxlen) + len = maxlen; + + if (i2c_write (addr[0], offset, alen-1, buffer, len) != 0) + rcode = 1; + + buffer += len; + offset += len; + +#if defined(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS) + udelay(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS * 1000); +#endif + } +#if defined(CONFIG_SYS_EEPROM_WREN) + eeprom_write_enable(dev_addr, 0); +#endif + return rcode; +} + +int bootstrap_eeprom_read (unsigned dev_addr, unsigned offset, + uchar *buffer, unsigned cnt) +{ + unsigned end = offset + cnt; + unsigned blk_off; + int rcode = 0; + + /* + * Read data until done or would cross a page boundary. + * We must write the address again when changing pages + * because the next page may be in a different device. + */ + while (offset < end) { + unsigned alen, len; + unsigned maxlen; + uchar addr[2]; + + blk_off = offset & 0xFF; /* block offset */ + + addr[0] = offset >> 8; /* block number */ + addr[1] = blk_off; /* block offset */ + alen = 2; + + addr[0] |= dev_addr; /* insert device address */ + + len = end - offset; + + maxlen = 0x100 - blk_off; + if (maxlen > I2C_RXTX_LEN) + maxlen = I2C_RXTX_LEN; + if (len > maxlen) + len = maxlen; + + if (i2c_read (addr[0], offset, alen-1, buffer, len) != 0) + rcode = 1; + buffer += len; + offset += len; + } + + return rcode; +} + +#if defined(CONFIG_USB_OHCI_NEW) && defined(CONFIG_SYS_USB_OHCI_BOARD_INIT) +int usb_board_init(void) +{ + char *act = getenv("usbact"); + int i; + + if ((act == NULL || strcmp(act, "host") == 0) && + !(in_be32((void*)GPIO0_IR) & GPIO0_USB_PRSNT)) + /* enable power on USB socket */ + out_be32((void*)GPIO1_OR, + in_be32((void*)GPIO1_OR) & ~GPIO1_USB_PWR_N); + + for (i=0; i<1000; i++) + udelay(1000); + + return 0; +} + +int usb_board_stop(void) +{ + /* disable power on USB socket */ + out_be32((void*)GPIO1_OR, in_be32((void*)GPIO1_OR) | GPIO1_USB_PWR_N); + return 0; +} + +int usb_board_init_fail(void) +{ + usb_board_stop(); + return 0; +} +#endif /* defined(CONFIG_USB_OHCI) && defined(CONFIG_SYS_USB_OHCI_BOARD_INIT) */ + +#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + int rc; + + __ft_board_setup(blob, bd); + + /* + * Disable PCI in non-monarch mode. + */ + if (!is_monarch()) { + rc = fdt_find_and_setprop(blob, "/plb/pci@1ec000000", "status", + "disabled", sizeof("disabled"), 1); + if (rc) { + printf("Unable to update property status in PCI node, err=%s\n", + fdt_strerror(rc)); + } + } +} +#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ |