diff options
Diffstat (limited to 'u-boot/board/r360mpi/pcmcia.c')
| -rw-r--r-- | u-boot/board/r360mpi/pcmcia.c | 236 |
1 files changed, 236 insertions, 0 deletions
diff --git a/u-boot/board/r360mpi/pcmcia.c b/u-boot/board/r360mpi/pcmcia.c new file mode 100644 index 0000000..85da41b --- /dev/null +++ b/u-boot/board/r360mpi/pcmcia.c @@ -0,0 +1,236 @@ +#include <common.h> +#include <mpc8xx.h> +#include <pcmcia.h> + +#undef CONFIG_PCMCIA + +#if defined(CONFIG_CMD_PCMCIA) +#define CONFIG_PCMCIA +#endif + +#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD) +#define CONFIG_PCMCIA +#endif + +#ifdef CONFIG_PCMCIA + +#define PCMCIA_BOARD_MSG "R360MPI" + +int pcmcia_hardware_enable(int slot) +{ + volatile immap_t *immap; + volatile cpm8xx_t *cp; + volatile pcmconf8xx_t *pcmp; + volatile sysconf8xx_t *sysp; + uint reg, mask; + + debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot); + + udelay(10000); + + immap = (immap_t *)CONFIG_SYS_IMMR; + sysp = (sysconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_siu_conf)); + pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia)); + cp = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm)); + + /* + * Configure SIUMCR to enable PCMCIA port B + * (VFLS[0:1] are not used for debugging, we connect FRZ# instead) + */ + sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */ + + /* clear interrupt state, and disable interrupts */ + pcmp->pcmc_pscr = PCMCIA_MASK(_slot_); + pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_); + + /* + * Disable interrupts, DMA, and PCMCIA buffers + * (isolate the interface) and assert RESET signal + */ + debug ("Disable PCMCIA buffers and assert RESET\n"); + reg = 0; + reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX(_slot_) = reg; + udelay(500); + + /* + * Configure Ports A, B & C pins for + * 5 Volts Enable and 3 Volts enable + */ + immap->im_ioport.iop_pcpar &= ~(0x0400); + immap->im_ioport.iop_pcso &= ~(0x0400);/* + immap->im_ioport.iop_pcdir |= 0x0400;*/ + + immap->im_ioport.iop_papar &= ~(0x0200);/* + immap->im_ioport.iop_padir |= 0x0200;*/ +#if 0 + immap->im_ioport.iop_pbpar &= ~(0xC000); + immap->im_ioport.iop_pbdir &= ~(0xC000); +#endif + /* remove all power */ + + immap->im_ioport.iop_pcdat |= 0x0400; + immap->im_ioport.iop_padat |= 0x0200; + + /* + * Make sure there is a card in the slot, then configure the interface. + */ + udelay(10000); + debug ("[%d] %s: PIPR(%p)=0x%x\n", + __LINE__,__FUNCTION__, + &(pcmp->pcmc_pipr),pcmp->pcmc_pipr); + if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) { + printf (" No Card found\n"); + return (1); + } + + /* + * Power On. + */ + mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot); + reg = pcmp->pcmc_pipr; + debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", + reg, + (reg&PCMCIA_VS1(slot))?"n":"ff", + (reg&PCMCIA_VS2(slot))?"n":"ff"); + if ((reg & mask) == mask) { + immap->im_ioport.iop_pcdat &= ~(0x4000); + puts (" 5.0V card found: "); + } else { + immap->im_ioport.iop_padat &= ~(0x0002); + puts (" 3.3V card found: "); + } + immap->im_ioport.iop_pcdir |= 0x0400; + immap->im_ioport.iop_padir |= 0x0200; +#if 0 + /* VCC switch error flag, PCMCIA slot INPACK_ pin */ + cp->cp_pbdir &= ~(0x0020 | 0x0010); + cp->cp_pbpar &= ~(0x0020 | 0x0010); + udelay(500000); +#endif + debug ("Enable PCMCIA buffers and stop RESET\n"); + reg = PCMCIA_PGCRX(_slot_); + reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX(_slot_) = reg; + + udelay(250000); /* some cards need >150 ms to come up :-( */ + + debug ("# hardware_enable done\n"); + + return (0); +} + + +#if defined(CONFIG_CMD_PCMCIA) +int pcmcia_hardware_disable(int slot) +{ + volatile immap_t *immap; + volatile pcmconf8xx_t *pcmp; + u_long reg; + + debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot); + + immap = (immap_t *)CONFIG_SYS_IMMR; + pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia)); + + /* remove all power */ + immap->im_ioport.iop_pcdat |= 0x0400; + immap->im_ioport.iop_padat |= 0x0200; + + /* Configure PCMCIA General Control Register */ + debug ("Disable PCMCIA buffers and assert RESET\n"); + reg = 0; + reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX(_slot_) = reg; + + udelay(10000); + + return (0); +} +#endif + + +int pcmcia_voltage_set(int slot, int vcc, int vpp) +{ + volatile immap_t *immap; + volatile pcmconf8xx_t *pcmp; + u_long reg; + + debug ("voltage_set: " + PCMCIA_BOARD_MSG + " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n", + 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10); + + immap = (immap_t *)CONFIG_SYS_IMMR; + pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia)); + /* + * Disable PCMCIA buffers (isolate the interface) + * and assert RESET signal + */ + debug ("Disable PCMCIA buffers and assert RESET\n"); + reg = PCMCIA_PGCRX(_slot_); + reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX(_slot_) = reg; + udelay(500); + + /* + * Configure Ports A & C pins for + * 5 Volts Enable and 3 Volts enable, + * Turn off all power + */ + debug ("PCMCIA power OFF\n"); + immap->im_ioport.iop_pcpar &= ~(0x0400); + immap->im_ioport.iop_pcso &= ~(0x0400);/* + immap->im_ioport.iop_pcdir |= 0x0400;*/ + + immap->im_ioport.iop_papar &= ~(0x0200);/* + immap->im_ioport.iop_padir |= 0x0200;*/ + + immap->im_ioport.iop_pcdat |= 0x0400; + immap->im_ioport.iop_padat |= 0x0200; + + reg = 0; + switch(vcc) { + case 0: break; + case 33: reg |= 0x0200; break; + case 50: reg |= 0x0400; break; + default: goto done; + } + + /* Checking supported voltages */ + + debug ("PIPR: 0x%x --> %s\n", + pcmp->pcmc_pipr, + (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V"); + + if (reg & 0x0200) + immap->im_ioport.iop_pcdat &= !reg; + if (reg & 0x0400) + immap->im_ioport.iop_padat &= !reg; + immap->im_ioport.iop_pcdir |= 0x0200; + immap->im_ioport.iop_padir |= 0x0400; + if (reg) { + debug ("PCMCIA powered at %sV\n", + (reg&0x0400) ? "5.0" : "3.3"); + } else { + debug ("PCMCIA powered down\n"); + } + +done: + debug ("Enable PCMCIA buffers and stop RESET\n"); + reg = PCMCIA_PGCRX(_slot_); + reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX(_slot_) = reg; + udelay(500); + + debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n", + slot+'A'); + return (0); +} + +#endif /* CCONFIG_PCMCIA */ |