diff options
Diffstat (limited to 'u-boot/board/sandburst/metrobox/metrobox.c')
| -rw-r--r-- | u-boot/board/sandburst/metrobox/metrobox.c | 583 |
1 files changed, 583 insertions, 0 deletions
diff --git a/u-boot/board/sandburst/metrobox/metrobox.c b/u-boot/board/sandburst/metrobox/metrobox.c new file mode 100644 index 0000000..76d8293 --- /dev/null +++ b/u-boot/board/sandburst/metrobox/metrobox.c @@ -0,0 +1,583 @@ +/* + * Copyright (c) 2005 + * Travis B. Sawyer, Sandburst Corporation, tsawyer@sandburst.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include <config.h> +#include <common.h> +#include <command.h> +#include "metrobox.h" +#include "metrobox_version.h" +#include <timestamp.h> +#include <asm/processor.h> +#include <asm/io.h> +#include <spd_sdram.h> +#include <i2c.h> +#include "../common/ppc440gx_i2c.h" +#include "../common/sb_common.h" +#if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) || \ + defined(CONFIG_HAS_ETH2) || defined(CONFIG_HAS_ETH3) +#include <net.h> +#endif + +void fpga_init (void); + +METROBOX_BOARD_ID_ST board_id_as[] = +{ {"Undefined"}, /* Not specified */ + {"2x10Gb"}, /* 2 ports, 10 GbE */ + {"20x1Gb"}, /* 20 ports, 1 GbE */ + {"Reserved"}, /* Reserved for future use */ +}; + +/************************************************************************* + * board_early_init_f + * + * Setup chip selects, initialize the Opto-FPGA, initialize + * interrupt polarity and triggers. + ************************************************************************/ +int board_early_init_f (void) +{ + ppc440_gpio_regs_t *gpio_regs; + + /* Enable GPIO interrupts */ + mtsdr(SDR0_PFC0, 0x00103E00); + + /* Setup access for LEDs, and system topology info */ + gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE; + gpio_regs->open_drain = SBCOMMON_GPIO_SYS_LEDS; + gpio_regs->tri_state = SBCOMMON_GPIO_DBGLEDS; + + /* Turn on all the leds for now */ + gpio_regs->out = SBCOMMON_GPIO_LEDS; + + /*--------------------------------------------------------------------+ + | Initialize EBC CONFIG + +-------------------------------------------------------------------*/ + mtebc(EBC0_CFG, + EBC_CFG_LE_UNLOCK | EBC_CFG_PTD_ENABLE | + EBC_CFG_RTC_64PERCLK | EBC_CFG_ATC_PREVIOUS | + EBC_CFG_DTC_PREVIOUS | EBC_CFG_CTC_PREVIOUS | + EBC_CFG_EMC_DEFAULT | EBC_CFG_PME_DISABLE | + EBC_CFG_PR_32); + + /*--------------------------------------------------------------------+ + | 1/2 MB FLASH. Initialize bank 0 with default values. + +-------------------------------------------------------------------*/ + mtebc(PB0AP, + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) | + EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) | + EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) | + EBC_BXAP_WBF_ENCODE(1)| EBC_BXAP_TH_ENCODE(1) | + EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY | + EBC_BXAP_PEN_DISABLED); + + mtebc(PB0CR, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) | + EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT); + /*--------------------------------------------------------------------+ + | 8KB NVRAM/RTC. Initialize bank 1 with default values. + +-------------------------------------------------------------------*/ + mtebc(PB1AP, + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(10) | + EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) | + EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) | + EBC_BXAP_WBF_ENCODE(1)| EBC_BXAP_TH_ENCODE(1) | + EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY | + EBC_BXAP_PEN_DISABLED); + + mtebc(PB1CR, EBC_BXCR_BAS_ENCODE(0x48000000) | + EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT); + + /*--------------------------------------------------------------------+ + | Compact Flash, uses 2 Chip Selects (2 & 6) + +-------------------------------------------------------------------*/ + mtebc(PB2AP, + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) | + EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) | + EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) | + EBC_BXAP_WBF_ENCODE(0)| EBC_BXAP_TH_ENCODE(1) | + EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY | + EBC_BXAP_PEN_DISABLED); + + mtebc(PB2CR, EBC_BXCR_BAS_ENCODE(0xF0000000) | + EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT); + + /*--------------------------------------------------------------------+ + | OPTO & OFEM FPGA. Initialize bank 3 with default values. + +-------------------------------------------------------------------*/ + mtebc(PB3AP, + EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED | + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) | + EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) | + EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED | + EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW); + + mtebc(PB3CR, EBC_BXCR_BAS_ENCODE(0x48200000) | + EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT); + + /*--------------------------------------------------------------------+ + | MAC A for metrobox + | MAC A & B for Kamino. OFEM FPGA decodes the addresses + | Initialize bank 4 with default values. + +-------------------------------------------------------------------*/ + mtebc(PB4AP, + EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED | + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) | + EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) | + EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED | + EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW); + + mtebc(PB4CR, EBC_BXCR_BAS_ENCODE(0x48600000) | + EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT); + + /*--------------------------------------------------------------------+ + | Metrobox MAC B Initialize bank 5 with default values. + | KA REF FPGA Initialize bank 5 with default values. + +-------------------------------------------------------------------*/ + mtebc(PB5AP, + EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED | + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) | + EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) | + EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED | + EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW); + + mtebc(PB5CR, EBC_BXCR_BAS_ENCODE(0x48700000) | + EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT); + + /*--------------------------------------------------------------------+ + | Compact Flash, uses 2 Chip Selects (2 & 6) + +-------------------------------------------------------------------*/ + mtebc(PB6AP, + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) | + EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) | + EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) | + EBC_BXAP_WBF_ENCODE(0)| EBC_BXAP_TH_ENCODE(1) | + EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY | + EBC_BXAP_PEN_DISABLED); + + mtebc(PB6CR, EBC_BXCR_BAS_ENCODE(0xF0100000) | + EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT); + + /*--------------------------------------------------------------------+ + | BME-32. Initialize bank 7 with default values. + +-------------------------------------------------------------------*/ + mtebc(PB7AP, + EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED | + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) | + EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) | + EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED | + EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW); + + mtebc(PB7CR, EBC_BXCR_BAS_ENCODE(0x48500000) | + EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT); + + /*--------------------------------------------------------------------+ + * Setup the interrupt controller polarities, triggers, etc. + +-------------------------------------------------------------------*/ + /* + * Because of the interrupt handling rework to handle 440GX interrupts + * with the common code, we needed to change names of the UIC registers. + * Here the new relationship: + * + * U-Boot name 440GX name + * ----------------------- + * UIC0 UICB0 + * UIC1 UIC0 + * UIC2 UIC1 + * UIC3 UIC2 + */ + mtdcr (UIC1SR, 0xffffffff); /* clear all */ + mtdcr (UIC1ER, 0x00000000); /* disable all */ + mtdcr (UIC1CR, 0x00000000); /* all non- critical */ + mtdcr (UIC1PR, 0xfffffe03); /* polarity */ + mtdcr (UIC1TR, 0x01c00000); /* trigger edge vs level */ + mtdcr (UIC1VR, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr (UIC1SR, 0xffffffff); /* clear all */ + + mtdcr (UIC2SR, 0xffffffff); /* clear all */ + mtdcr (UIC2ER, 0x00000000); /* disable all */ + mtdcr (UIC2CR, 0x00000000); /* all non-critical */ + mtdcr (UIC2PR, 0xffffc8ff); /* polarity */ + mtdcr (UIC2TR, 0x00ff0000); /* trigger edge vs level */ + mtdcr (UIC2VR, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr (UIC2SR, 0xffffffff); /* clear all */ + + mtdcr (UIC3SR, 0xffffffff); /* clear all */ + mtdcr (UIC3ER, 0x00000000); /* disable all */ + mtdcr (UIC3CR, 0x00000000); /* all non-critical */ + mtdcr (UIC3PR, 0xffff83ff); /* polarity */ + mtdcr (UIC3TR, 0x00ff8c0f); /* trigger edge vs level */ + mtdcr (UIC3VR, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr (UIC3SR, 0xffffffff); /* clear all */ + + mtdcr (UIC0SR, 0xfc000000); /* clear all */ + mtdcr (UIC0ER, 0x00000000); /* disable all */ + mtdcr (UIC0CR, 0x00000000); /* all non-critical */ + mtdcr (UIC0PR, 0xfc000000); + mtdcr (UIC0TR, 0x00000000); + mtdcr (UIC0VR, 0x00000001); + + fpga_init(); + + return 0; +} + +/************************************************************************* + * checkboard + * + * Dump pertinent info to the console + ************************************************************************/ +int checkboard (void) +{ + sys_info_t sysinfo; + unsigned char brd_rev, brd_id; + unsigned short sernum; + unsigned char opto_rev, opto_id; + OPTO_FPGA_REGS_ST *opto_ps; + + opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE; + + opto_rev = (unsigned char)((opto_ps->revision_ul & + SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_MASK) + >> SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_SHIFT); + + opto_id = (unsigned char)((opto_ps->revision_ul & + SAND_HAL_XC_XCVR_CNTL_REVISION_IDENTIFICATION_MASK) + >> SAND_HAL_XC_XCVR_CNTL_REVISION_IDENTIFICATION_SHIFT); + + brd_rev = (unsigned char)((opto_ps->boardinfo_ul & + SAND_HAL_XC_XCVR_CNTL_BRD_INFO_BRD_REV_MASK) + >> SAND_HAL_XC_XCVR_CNTL_BRD_INFO_BRD_REV_SHIFT); + + brd_id = (unsigned char)((opto_ps->boardinfo_ul & + SAND_HAL_XC_XCVR_CNTL_BRD_INFO_BRD_ID_MASK) + >> SAND_HAL_XC_XCVR_CNTL_BRD_INFO_BRD_ID_SHIFT); + + get_sys_info (&sysinfo); + + sernum = sbcommon_get_serial_number(); + printf ("Board: Sandburst Corporation MetroBox Serial Number: %d\n", sernum); + printf ("%s\n", METROBOX_U_BOOT_REL_STR); + + printf ("Built %s %s by %s\n", U_BOOT_DATE, U_BOOT_TIME, BUILDUSER); + if (sbcommon_get_master()) { + printf("Slot 0 - Master\nSlave board"); + if (sbcommon_secondary_present()) + printf(" present\n"); + else + printf(" not detected\n"); + } else { + printf("Slot 1 - Slave\n\n"); + } + + printf ("OptoFPGA ID:\t0x%02X\tRev: 0x%02X\n", opto_id, opto_rev); + printf ("Board Rev:\t0x%02X\tID: %s\n", brd_rev, board_id_as[brd_id].name); + + /* Fix the ack in the bme 32 */ + udelay(5000); + out32(CONFIG_SYS_BME32_BASE + 0x0000000C, 0x00000001); + asm("eieio"); + + + return (0); +} + +/************************************************************************* + * misc_init_f + * + * Initialize I2C bus one to gain access to the fans + ************************************************************************/ +int misc_init_f (void) +{ + /* Turn on i2c bus 1 */ + puts ("I2C1: "); + i2c1_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + puts ("ready\n"); + + /* Turn on fans */ + sbcommon_fans(); + + return (0); +} + +/************************************************************************* + * misc_init_r + * + * Do nothing. + ************************************************************************/ +int misc_init_r (void) +{ + unsigned short sernum; + char envstr[255]; + uchar enetaddr[6]; + unsigned char opto_rev; + OPTO_FPGA_REGS_ST *opto_ps; + + opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE; + + if(NULL != getenv("secondserial")) { + puts("secondserial is set, switching to second serial port\n"); + setenv("stderr", "serial1"); + setenv("stdout", "serial1"); + setenv("stdin", "serial1"); + } + + setenv("ubrelver", METROBOX_U_BOOT_REL_STR); + + memset(envstr, 0, 255); + sprintf (envstr, "Built %s %s by %s", + U_BOOT_DATE, U_BOOT_TIME, BUILDUSER); + setenv("bldstr", envstr); + saveenv(); + + if( getenv("autorecover")) { + setenv("autorecover", NULL); + saveenv(); + sernum = sbcommon_get_serial_number(); + + printf("\nSetting up environment for automatic filesystem recovery\n"); + /* + * Setup default bootargs + */ + memset(envstr, 0, 255); + sprintf(envstr, "console=ttyS0,9600 root=/dev/ram0 " + "rw ip=10.100.60.%d:::255.255.0.0:metrobox%d:eth0:none idebus=33", + sernum, sernum); + setenv("bootargs", envstr); + + /* + * Setup Default boot command + */ + setenv("bootcmd", "fatload ide 0 8000000 pimage.metrobox;" + "fatload ide 0 8100000 pramdisk;" + "bootm 8000000 8100000"); + + printf("Done. Please type allow the system to continue to boot\n"); + } + + if( getenv("fakeled")) { + setenv("bootdelay", "-1"); + saveenv(); + printf("fakeled is set. use 'setenv fakeled ; setenv bootdelay 5 ; saveenv' to recover\n"); + opto_rev = (unsigned char)((opto_ps->revision_ul & + SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_MASK) + >> SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_SHIFT); + + if(0x12 <= opto_rev) { + opto_ps->control_ul &= ~ SAND_HAL_XC_XCVR_CNTL_CNTL_ERROR_LED_MASK; + } + } + +#ifdef CONFIG_HAS_ETH0 + if (!eth_getenv_enetaddr("ethaddr", enetaddr)) { + board_get_enetaddr(0, enetaddr); + eth_setenv_enetaddr("ethaddr", enetaddr); + } +#endif + +#ifdef CONFIG_HAS_ETH1 + if (!eth_getenv_enetaddr("eth1addr", enetaddr)) { + board_get_enetaddr(1, enetaddr); + eth_setenv_enetaddr("eth1addr", enetaddr); + } +#endif + +#ifdef CONFIG_HAS_ETH2 + if (!eth_getenv_enetaddr("eth2addr", enetaddr)) { + board_get_enetaddr(2, enetaddr); + eth_setenv_enetaddr("eth2addr", enetaddr); + } +#endif + +#ifdef CONFIG_HAS_ETH3 + if (!eth_getenv_enetaddr("eth3addr", enetaddr)) { + board_get_enetaddr(3, enetaddr); + eth_setenv_enetaddr("eth3addr", enetaddr); + } +#endif + + return (0); +} + +/************************************************************************* + * ide_set_reset + ************************************************************************/ +#ifdef CONFIG_IDE_RESET +void ide_set_reset(int on) +{ + OPTO_FPGA_REGS_ST *opto_ps; + opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE; + + if (on) { /* assert RESET */ + opto_ps->reset_ul &= ~SAND_HAL_XC_XCVR_CNTL_RESET_CF_RESET_N_MASK; + } else { /* release RESET */ + opto_ps->reset_ul |= SAND_HAL_XC_XCVR_CNTL_RESET_CF_RESET_N_MASK; + } +} +#endif /* CONFIG_IDE_RESET */ + +/************************************************************************* + * fpga_init + ************************************************************************/ +void fpga_init(void) +{ + OPTO_FPGA_REGS_ST *opto_ps; + unsigned char opto_rev; + unsigned long tmp; + + /* Ensure we have power all around */ + udelay(500); + + /* + * Take appropriate hw bits out of reset + */ + opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE; + + tmp = + SAND_HAL_XC_XCVR_CNTL_RESET_MAC1_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_MAC0_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_BME_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_ACE_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_CF_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_QE_A_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_IFE_A_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_EFE_A_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_QE_B_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_IFE_B_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_EFE_B_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_LOCK1_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_LOCK0_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_I2C_MUX1_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_I2C_MUX0_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_PHY0_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_PHY1_RESET_N_MASK | + SAND_HAL_XC_XCVR_CNTL_RESET_SLAVE_RESET_N_MASK; + opto_ps->reset_ul = tmp; + /* + * Turn on the 'Slow Blink' for the System Error Led. + * Ensure FPGA rev is up to at least rev 0x12 + */ + opto_rev = (unsigned char)((opto_ps->revision_ul & + SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_MASK) + >> SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_SHIFT); + if(0x12 <= opto_rev) { + opto_ps->control_ul |= 1 << SAND_HAL_XC_XCVR_CNTL_CNTL_ERROR_LED_SHIFT; + } + + asm("eieio"); + + return; +} + +int metroboxSetupVars(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + unsigned short sernum; + char envstr[255]; + + sernum = sbcommon_get_serial_number(); + + memset(envstr, 0, 255); + /* + * Setup our ip address + */ + sprintf(envstr, "10.100.60.%d", sernum); + + setenv("ipaddr", envstr); + /* + * Setup the host ip address + */ + setenv("serverip", "10.100.17.10"); + + /* + * Setup default bootargs + */ + memset(envstr, 0, 255); + + sprintf(envstr, "console=ttyS0,9600 root=/dev/nfs " + "rw nfsroot=10.100.17.10:/home/metrobox/mbc%d " + "nfsaddrs=10.100.60.%d:10.100.17.10:10.100.1.1" + ":255.255.0.0:metrobox%d.sandburst.com:eth0:none idebus=33", + sernum, sernum, sernum); + + setenv("bootargs_nfs", envstr); + setenv("bootargs", envstr); + + /* + * Setup CF bootargs + */ + memset(envstr, 0, 255); + sprintf(envstr, "console=ttyS0,9600 root=/dev/hda2 " + "rw ip=10.100.60.%d:::255.255.0.0:metrobox%d:eth0:none idebus=33", + sernum, sernum); + + setenv("bootargs_cf", envstr); + + /* + * Setup Default boot command + */ + setenv("bootcmd_tftp", "tftp 8000000 pImage.metrobox;bootm 8000000"); + setenv("bootcmd", "tftp 8000000 pImage.metrobox;bootm 8000000"); + + /* + * Setup compact flash boot command + */ + setenv("bootcmd_cf", "fatload ide 0 8000000 pimage.metrobox;bootm 8000000"); + + saveenv(); + + + return(1); +} + +int metroboxRecover(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + unsigned short sernum; + char envstr[255]; + + sernum = sbcommon_get_serial_number(); + + printf("\nSetting up environment for filesystem recovery\n"); + /* + * Setup default bootargs + */ + memset(envstr, 0, 255); + sprintf(envstr, "console=ttyS0,9600 root=/dev/ram0 " + "rw ip=10.100.60.%d:::255.255.0.0:metrobox%d:eth0:none", + sernum, sernum); + + setenv("bootargs", envstr); + + /* + * Setup Default boot command + */ + setenv("bootcmd", "fatload ide 0 8000000 pimage.metrobox;" + "fatload ide 0 8100000 pramdisk;" + "bootm 8000000 8100000"); + + printf("Done. Please type boot<cr>.\nWhen the kernel has booted" + " please type fsrecover.sh<cr>\n"); + + return(1); +} + +U_BOOT_CMD(mbsetup, 1, 1, metroboxSetupVars, + "Set environment to factory defaults", ""); + +U_BOOT_CMD(mbrecover, 1, 1, metroboxRecover, + "Set environment to allow for fs recovery", ""); |