summaryrefslogtreecommitdiffstats
path: root/u-boot/doc/README.mpc8315erdb
diff options
context:
space:
mode:
Diffstat (limited to 'u-boot/doc/README.mpc8315erdb')
-rw-r--r--u-boot/doc/README.mpc8315erdb105
1 files changed, 105 insertions, 0 deletions
diff --git a/u-boot/doc/README.mpc8315erdb b/u-boot/doc/README.mpc8315erdb
new file mode 100644
index 0000000..b32132d
--- /dev/null
+++ b/u-boot/doc/README.mpc8315erdb
@@ -0,0 +1,105 @@
+Freescale MPC8315ERDB Board
+-----------------------------------------
+
+1. Board Switches and Jumpers
+
+ S3 is used to set CONFIG_SYS_RESET_SOURCE.
+
+ To boot the image at 0xFE000000 in NOR flash, use these DIP
+ switch settings for S3 S4:
+
+ +------+ +------+
+ | | | **** |
+ | **** | | |
+ +------+ ON +------+ ON
+ 4321 4321
+ (where the '*' indicates the position of the tab of the switch.)
+
+ To boot the image at the beginning of NAND flash, use these
+ DIP switch settings for S3 S4:
+
+ +------+ +------+
+ | * | | *** |
+ | *** | | * |
+ +------+ ON +------+ ON
+ 4321 4321
+ (where the '*' indicates the position of the tab of the switch.)
+
+ When booting from NAND, use u-boot-nand.bin, not u-boot.bin.
+
+2. Memory Map
+ The memory map looks like this:
+
+ 0x0000_0000 0x07ff_ffff DDR 128M
+ 0x8000_0000 0x8fff_ffff PCI MEM 256M
+ 0x9000_0000 0x9fff_ffff PCI_MMIO 256M
+ 0xe000_0000 0xe00f_ffff IMMR 1M
+ 0xe030_0000 0xe03f_ffff PCI IO 1M
+ 0xe060_0000 0xe060_7fff NAND FLASH (CS1) 32K
+ 0xfe00_0000 0xfe7f_ffff NOR FLASH (CS0) 8M
+
+ When booting from NAND, NAND flash is CS0 and NOR flash
+ is CS1.
+
+3. Definitions
+
+3.1 Explanation of NEW definitions in:
+
+ include/configs/MPC8315ERDB.h
+
+ CONFIG_MPC83xx MPC83xx family
+ CONFIG_MPC831x MPC831x specific
+ CONFIG_MPC8315 MPC8315 specific
+ CONFIG_MPC8315ERDB MPC8315ERDB board specific
+
+4. Compilation
+
+ Assuming you're using BASH (or similar) as your shell:
+
+ export CROSS_COMPILE=your-cross-compiler-prefix-
+ make distclean
+ make MPC8315ERDB_config (or MPC8315ERDB_NAND_config for u-boot-nand.bin)
+ make all
+
+5. Downloading and Flashing Images
+
+5.1 Reflash U-boot Image using U-boot
+
+ NOR flash:
+
+ tftp 40000 u-boot.bin
+ protect off all
+ erase fe000000 fe1fffff
+
+ cp.b 40000 fe000000 xxxx
+ protect on all
+
+ You have to supply the correct byte count with 'xxxx'
+ from the TFTP result log.
+
+ NAND flash:
+
+ =>tftpboot $loadaddr <filename>
+ =>nand erase 0 0x80000
+ =>nand write $loadaddr 0 0x80000
+
+ ...where 0x80000 is the filesize rounded up to
+ the next 0x20000 increment.
+
+5.2 Downloading and Booting Linux Kernel
+
+ Ensure that all networking-related environment variables are set
+ properly (including ipaddr, serverip, gatewayip (if needed),
+ netmask, ethaddr, eth1addr, rootpath (if using NFS root),
+ fdtfile, and bootfile).
+
+ Then, do one of the following, depending on whether you
+ want an NFS root or a ramdisk root:
+
+ =>run nfsboot
+ or
+ =>run ramboot
+
+6 Notes
+
+ The console baudrate for MPC8315ERDB is 115200bps.