diff options
Diffstat (limited to 'u-boot/include/configs/APC405.h')
| -rw-r--r-- | u-boot/include/configs/APC405.h | 443 |
1 files changed, 443 insertions, 0 deletions
diff --git a/u-boot/include/configs/APC405.h b/u-boot/include/configs/APC405.h new file mode 100644 index 0000000..0adf3ed --- /dev/null +++ b/u-boot/include/configs/APC405.h @@ -0,0 +1,443 @@ +/* + * (C) Copyright 2005-2008 + * Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com + * + * (C) Copyright 2001-2004 + * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_405GP 1 /* This is a PPC405 CPU */ +#define CONFIG_4xx 1 /* ...member of PPC4xx family */ +#define CONFIG_APCG405 1 /* ...on a APC405 board */ + +#define CONFIG_SYS_TEXT_BASE 0xFFF80000 + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ +#define CONFIG_BOARD_EARLY_INIT_R 1 +#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ + +#define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */ + +#define CONFIG_BOARD_TYPES 1 /* support board types */ + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_BOOTDELAY 1 /* autoboot after 3 seconds */ +#define CONFIG_BOOTCOUNT_LIMIT 1 + +#undef CONFIG_BOOTARGS + +#define CONFIG_SYS_USB_LOAD_COMMAND "fatload usb 0 200000 pImage;" \ + "fatload usb 0 300000 pImage.initrd" +#define CONFIG_SYS_USB_SELF_COMMAND "usb start;run usb_load;usb stop;" \ + "run ramargs addip addcon usbargs;" \ + "bootm 200000 300000" +#define CONFIG_SYS_USB_ARGS "setenv bootargs $(bootargs) usbboot=1" +#define CONFIG_SYS_BOOTLIMIT "3" +#define CONFIG_SYS_ALT_BOOTCOMMAND "run usb_self;reset" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hostname=abg405\0" \ + "bd_type=abg405\0" \ + "serial#=AA0000\0" \ + "kernel_addr=fe000000\0" \ + "ramdisk_addr=fe100000\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath)\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ + ":$(hostname)::off panic=1\0" \ + "addcon=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)" \ + " $(optargs)\0" \ + "flash_self=run ramargs addip addcon;" \ + "bootm $(kernel_addr) $(ramdisk_addr)\0" \ + "net_nfs=tftp 200000 $(img);run nfsargs addip addcon;" \ + "bootm\0" \ + "rootpath=/tftpboot/abg405/target_root\0" \ + "img=/tftpboot/abg405/pImage\0" \ + "load=tftp 100000 /tftpboot/abg405/u-boot.bin\0" \ + "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \ + "cp.b 100000 fff80000 80000\0" \ + "ipaddr=10.0.111.111\0" \ + "netmask=255.255.0.0\0" \ + "serverip=10.0.0.190\0" \ + "splashimage=ffe80000\0" \ + "usb_load="CONFIG_SYS_USB_LOAD_COMMAND"\0" \ + "usb_self="CONFIG_SYS_USB_SELF_COMMAND"\0" \ + "usbargs="CONFIG_SYS_USB_ARGS"\0" \ + "bootlimit="CONFIG_SYS_BOOTLIMIT"\0" \ + "altbootcmd="CONFIG_SYS_ALT_BOOTCOMMAND"\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self;reset" + +#define CONFIG_ETHADDR 00:02:27:8e:00:00 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_NET_MULTI 1 +#undef CONFIG_HAS_ETH1 + +#define CONFIG_PPC4xx_EMAC +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0 /* PHY address */ +#define CONFIG_LXT971_NO_SLEEP 1 +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() */ + +#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FAT +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IDE +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_SOURCE +#define CONFIG_CMD_USB + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_SUPPORT_VFAT + +#define CONFIG_AUTO_UPDATE 1 /* autoupdate via CF or USB */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/ +#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */ + +#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ + +#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ + +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + +#define CONFIG_SYS_EXT_SERIAL_CLOCK 14745600 /* use external serial clock */ + +/* The following table includes the supported baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE \ + { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ + 57600, 115200, 230400, 460800, 921600 } + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ + +/* Only interrupt boot if space is pressed */ +/* If a long serial cable is connected but */ +/* other end is dead, garbage will be read */ +#define CONFIG_AUTOBOOT_KEYED 1 +#define CONFIG_AUTOBOOT_PROMPT \ + "Press SPACE to abort autoboot in %d seconds\n", bootdelay +#undef CONFIG_AUTOBOOT_DELAY_STR +#define CONFIG_AUTOBOOT_STOP_STR " " + +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ + +/* + * PCI stuff + */ +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + /* resource configuration */ + +#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ +#define CONFIG_PCI_SKIP_HOST_BRIDGE 1 +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ +#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ +#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ +#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ +#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ +#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ + +/* + * IDE/ATA stuff + */ +#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ +#undef CONFIG_IDE_LED /* no led for ide supported */ +#define CONFIG_IDE_RESET 1 /* reset for ide supported */ + +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS) /* max. 1 drives per IDE bus */ + +#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register access */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */ + +/* + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_MONITOR_BASE 0xFFF80000 +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (2*1024*1024) /* Reserve 2MB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Init. Memory map for Linux */ + +/* + * FLASH organization + */ +#define CONFIG_SYS_FLASH_BASE 0xFE000000 +#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 +#define CONFIG_SYS_FLASH_QUIET_TEST 1 +#define CONFIG_SYS_FLASH_INCREMENT 0x01000000 +#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */ +#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { \ + {0xfe000000, 0x500000}, \ + {0xffe80000, 0x180000} \ + } +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_BANKS_LIST { \ + CONFIG_SYS_FLASH_BASE, \ + CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_INCREMENT \ + } +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +/* + * Environment Variable setup + */ +#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the */ + /* beginning of the EEPROM */ +#define CONFIG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/ +#define CONFIG_ENV_OVERWRITE 1 /* allow overwriting vendor vars */ + +#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */ +#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */ + +/* + * I2C EEPROM (CAT24WC16) for environment + */ +#define CONFIG_HARD_I2C /* I2c with hardware support */ +#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ +#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ + /* 16 byte page write mode using*/ + /* last 4 bits of the address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +/* + * External Bus Controller (EBC) Setup + */ +#define FLASH0_BA (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_INCREMENT) /* FLASH 0 BA */ +#define FLASH1_BA CONFIG_SYS_FLASH_BASE /* FLASH 1 Base Address */ +#define CAN_BA 0xF0000000 /* CAN Base Address */ +#define DUART0_BA 0xF0000400 /* DUART Base Address */ +#define DUART1_BA 0xF0000408 /* DUART Base Address */ +#define RTC_BA 0xF0000500 /* RTC Base Address */ +#define PS2_BA 0xF0000600 /* PS/2 Base Address */ +#define CF_BA 0xF0100000 /* CompactFlash Base Address */ +#define FPGA_BA 0xF0100100 /* FPGA internal Base Address */ +#define FUJI_BA 0xF0100200 /* Fuji internal Base Address */ +#define PCMCIA1_BA 0x20000000 /* PCMCIA Slot 1 Base Address */ +#define PCMCIA2_BA 0x28000000 /* PCMCIA Slot 2 Base Address */ +#define VGA_BA 0xF1000000 /* Epson VGA Base Address */ + +#define CONFIG_SYS_FPGA_BASE_ADDR FPGA_BA /* FPGA internal Base Address */ + +/* Memory Bank 0 (Flash Bank 0) initialization */ +#define CONFIG_SYS_EBC_PB0AP 0x92015480 +#define CONFIG_SYS_EBC_PB0CR FLASH0_BA | 0x9A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit*/ +#define CONFIG_SYS_EBC_PB0AP_HWREV8 CONFIG_SYS_EBC_PB0AP +#define CONFIG_SYS_EBC_PB0CR_HWREV8 FLASH1_BA | 0xBA000 /* BS=32MB */ + +/* Memory Bank 1 (Flash Bank 1) initialization */ +#define CONFIG_SYS_EBC_PB1AP 0x92015480 +#define CONFIG_SYS_EBC_PB1CR FLASH1_BA | 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/ + +/* Memory Bank 2 (CAN0, 1, RTC, Duart) initialization */ +#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CONFIG_SYS_EBC_PB2CR CAN_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ + +/* Memory Bank 3 (CompactFlash IDE, FPGA internal) initialization */ +#define CONFIG_SYS_EBC_PB3AP 0x010059C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CONFIG_SYS_EBC_PB3CR CF_BA | 0x1A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ + +/* Memory Bank 4 (PCMCIA Slot 1) initialization */ +#define CONFIG_SYS_EBC_PB4AP 0x050007C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CONFIG_SYS_EBC_PB4CR PCMCIA1_BA | 0xFA000 /*BAS=0x200,BS=128MB,BU=R/W,BW=16bit*/ + +/* Memory Bank 5 (Epson VGA) initialization */ +#define CONFIG_SYS_EBC_PB5AP 0x03805380 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=0 */ +#define CONFIG_SYS_EBC_PB5CR VGA_BA | 0x5A000 /* BAS=0xF10,BS=4MB,BU=R/W,BW=16bit */ + +/* Memory Bank 6 (PCMCIA Slot 2) initialization */ +#define CONFIG_SYS_EBC_PB6AP 0x050007C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CONFIG_SYS_EBC_PB6CR PCMCIA2_BA | 0xFA000 /*BAS=0x280,BS=128MB,BU=R/W,BW=16bit*/ + +/* + * FPGA stuff + */ + +/* FPGA internal regs */ +#define CONFIG_SYS_FPGA_CTRL 0x008 +#define CONFIG_SYS_FPGA_CTRL2 0x00a + +/* FPGA Control Reg */ +#define CONFIG_SYS_FPGA_CTRL_CF_RESET 0x0001 +#define CONFIG_SYS_FPGA_CTRL_WDI 0x0002 +#define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020 + +#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ +#define CONFIG_SYS_FPGA_MAX_SIZE 80*1024 /* 80kByte is enough for XC2S50 */ + +/* FPGA program pin configuration */ +#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ +#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ +#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ +#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ +#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ + +/* + * LCD Setup + */ +#define CONFIG_SYS_LCD_BIG_MEM (VGA_BA + 0x200000) /* S1D13806 Mem Base */ +#define CONFIG_SYS_LCD_BIG_REG VGA_BA /* S1D13806 Reg Base */ + +#define CONFIG_LCD_BIG 2 /* Epson S1D13806 used */ + +/* Image information... */ +#define CONFIG_LCD_USED CONFIG_LCD_BIG + +#define CONFIG_SYS_LCD_MEM CONFIG_SYS_LCD_BIG_MEM +#define CONFIG_SYS_LCD_REG CONFIG_SYS_LCD_BIG_REG + +#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (1 << 20) + +/* + * Definitions for initial stack pointer and data area (in data cache) + */ + +/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ +#define CONFIG_SYS_TEMP_STACK_OCM 1 + +/* On Chip Memory location */ +#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 + +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ +#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +/* reserve some memory for BOOT limit info */ +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 16) + +#ifdef CONFIG_BOOTCOUNT_LIMIT /* reserve 2 word for bootcount limit */ +#define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 8) +#endif + +/* + * PCI OHCI controller + */ +#define CONFIG_USB_OHCI_NEW 1 +#define CONFIG_PCI_OHCI 1 +#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" +#define CONFIG_USB_STORAGE 1 +#define CONFIG_SYS_USB_OHCI_BOARD_INIT 1 + +#endif /* __CONFIG_H */ |